diff options
Diffstat (limited to 'board/esd/hh405/hh405.c')
| -rw-r--r-- | board/esd/hh405/hh405.c | 426 |
1 files changed, 411 insertions, 15 deletions
diff --git a/board/esd/hh405/hh405.c b/board/esd/hh405/hh405.c index 64690ac1b0..9c582b121c 100644 --- a/board/esd/hh405/hh405.c +++ b/board/esd/hh405/hh405.c @@ -2,6 +2,9 @@ * (C) Copyright 2001-2004 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com * + * (C) Copyright 2005 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * * See file CREDITS for list of people who contributed to this * project. * @@ -25,8 +28,176 @@ #include <asm/processor.h> #include <command.h> #include <malloc.h> +#include <pci.h> +#include <sm501.h> + + +#ifdef CONFIG_VIDEO_SM501 + +#define SWAP32(x) ((((x) & 0x000000ff) << 24) | (((x) & 0x0000ff00) << 8)|\ + (((x) & 0x00ff0000) >> 8) | (((x) & 0xff000000) >> 24) ) + +#ifdef CONFIG_VIDEO_SM501_8BPP +#error CONFIG_VIDEO_SM501_8BPP not supported. +#endif /* CONFIG_VIDEO_SM501_8BPP */ + +#ifdef CONFIG_VIDEO_SM501_16BPP +#define BPP 16 + +/* + * 800x600 display B084SN03: PCLK = 40MHz + * => 2*PCLK = 80MHz + * 336/4 = 84MHz + * => PCLK = 84MHz + */ +static const SMI_REGS init_regs_800x600 [] = +{ +#if 1 /* test-only */ + {0x0005c, SWAP32(0xffffffff)}, /* set endianess to big endian */ +#else + {0x0005c, SWAP32(0x00000000)}, /* set endianess to little endian */ +#endif + {0x00004, SWAP32(0x00000000)}, + /* clocks for pm1... */ + {0x00048, SWAP32(0x00021807)}, + {0x0004C, SWAP32(0x221a0a01)}, + {0x00054, SWAP32(0x00000001)}, + /* clocks for pm0... */ + {0x00040, SWAP32(0x00021807)}, + {0x00044, SWAP32(0x221a0a01)}, + {0x00054, SWAP32(0x00000000)}, + /* panel control regs... */ + {0x80000, SWAP32(0x0f013105)}, /* panel display control: 16-bit RGB 5:6:5 mode */ + {0x80004, SWAP32(0xc428bb17)}, /* panel panning control ??? */ + {0x8000C, SWAP32(0x00000000)}, /* panel fb address */ + {0x80010, SWAP32(0x06400640)}, /* panel fb offset/window width */ + {0x80014, SWAP32(0x03200000)}, /* panel fb width (0x320=800) */ + {0x80018, SWAP32(0x02580000)}, /* panel fb height (0x258=600) */ + {0x8001C, SWAP32(0x00000000)}, /* panel plane tl location */ + {0x80020, SWAP32(0x02580320)}, /* panel plane br location */ + {0x80024, SWAP32(0x041f031f)}, /* panel horizontal total */ + {0x80028, SWAP32(0x00800347)}, /* panel horizontal sync */ + {0x8002C, SWAP32(0x02730257)}, /* panel vertical total */ + {0x80030, SWAP32(0x00040258)}, /* panel vertical sync */ + {0x80200, SWAP32(0x00010000)}, /* crt display control */ + {0, 0} +}; + +/* + * 1024x768 display G150XG02: PCLK = 65MHz + * => 2*PCLK = 130MHz + * 288/2 = 144MHz + * => PCLK = 72MHz + */ +static const SMI_REGS init_regs_1024x768 [] = +{ + {0x00004, SWAP32(0x00000000)}, + /* clocks for pm1... */ + {0x00048, SWAP32(0x00021807)}, + {0x0004C, SWAP32(0x011a0a01)}, + {0x00054, SWAP32(0x00000001)}, + /* clocks for pm0... */ + {0x00040, SWAP32(0x00021807)}, + {0x00044, SWAP32(0x011a0a01)}, + {0x00054, SWAP32(0x00000000)}, + /* panel control regs... */ + {0x80000, SWAP32(0x0f013105)}, /* panel display control: 16-bit RGB 5:6:5 mode */ + {0x80004, SWAP32(0xc428bb17)}, /* panel panning control ??? */ + {0x8000C, SWAP32(0x00000000)}, /* panel fb address */ + {0x80010, SWAP32(0x08000800)}, /* panel fb offset/window width */ + {0x80014, SWAP32(0x04000000)}, /* panel fb width (0x400=1024) */ + {0x80018, SWAP32(0x03000000)}, /* panel fb height (0x300=768) */ + {0x8001C, SWAP32(0x00000000)}, /* panel plane tl location */ + {0x80020, SWAP32(0x03000400)}, /* panel plane br location */ + {0x80024, SWAP32(0x053f03ff)}, /* panel horizontal total */ + {0x80028, SWAP32(0x0140040f)}, /* panel horizontal sync */ + {0x8002C, SWAP32(0x032502ff)}, /* panel vertical total */ + {0x80030, SWAP32(0x00260301)}, /* panel vertical sync */ + {0x80200, SWAP32(0x00010000)}, /* crt display control */ + {0, 0} +}; -/* ------------------------------------------------------------------------- */ +#endif /* CONFIG_VIDEO_SM501_16BPP */ + +#ifdef CONFIG_VIDEO_SM501_32BPP +#define BPP 32 + +/* + * 800x600 display B084SN03: PCLK = 40MHz + * => 2*PCLK = 80MHz + * 336/4 = 84MHz + * => PCLK = 84MHz + */ +static const SMI_REGS init_regs_800x600 [] = +{ +#if 0 /* test-only */ + {0x0005c, SWAP32(0xffffffff)}, /* set endianess to big endian */ +#else + {0x0005c, SWAP32(0x00000000)}, /* set endianess to little endian */ +#endif + {0x00004, SWAP32(0x00000000)}, + /* clocks for pm1... */ + {0x00048, SWAP32(0x00021807)}, + {0x0004C, SWAP32(0x221a0a01)}, + {0x00054, SWAP32(0x00000001)}, + /* clocks for pm0... */ + {0x00040, SWAP32(0x00021807)}, + {0x00044, SWAP32(0x221a0a01)}, + {0x00054, SWAP32(0x00000000)}, + /* panel control regs... */ + {0x80000, SWAP32(0x0f013106)}, /* panel display control: 32-bit RGB 8:8:8 mode */ + {0x80004, SWAP32(0xc428bb17)}, /* panel panning control ??? */ + {0x8000C, SWAP32(0x00000000)}, /* panel fb address */ + {0x80010, SWAP32(0x0c800c80)}, /* panel fb offset/window width */ + {0x80014, SWAP32(0x03200000)}, /* panel fb width (0x320=800) */ + {0x80018, SWAP32(0x02580000)}, /* panel fb height (0x258=600) */ + {0x8001C, SWAP32(0x00000000)}, /* panel plane tl location */ + {0x80020, SWAP32(0x02580320)}, /* panel plane br location */ + {0x80024, SWAP32(0x041f031f)}, /* panel horizontal total */ + {0x80028, SWAP32(0x00800347)}, /* panel horizontal sync */ + {0x8002C, SWAP32(0x02730257)}, /* panel vertical total */ + {0x80030, SWAP32(0x00040258)}, /* panel vertical sync */ + {0x80200, SWAP32(0x00010000)}, /* crt display control */ + {0, 0} +}; + +/* + * 1024x768 display G150XG02: PCLK = 65MHz + * => 2*PCLK = 130MHz + * 288/2 = 144MHz + * => PCLK = 72MHz + */ +static const SMI_REGS init_regs_1024x768 [] = +{ + {0x00004, SWAP32(0x00000000)}, + /* clocks for pm1... */ + {0x00048, SWAP32(0x00021807)}, + {0x0004C, SWAP32(0x011a0a01)}, + {0x00054, SWAP32(0x00000001)}, + /* clocks for pm0... */ + {0x00040, SWAP32(0x00021807)}, + {0x00044, SWAP32(0x011a0a01)}, + {0x00054, SWAP32(0x00000000)}, + /* panel control regs... */ + {0x80000, SWAP32(0x0f013106)}, /* panel display control: 32-bit RGB 8:8:8 mode */ + {0x80004, SWAP32(0xc428bb17)}, /* panel panning control ??? */ + {0x8000C, SWAP32(0x00000000)}, /* panel fb address */ + {0x80010, SWAP32(0x10001000)}, /* panel fb offset/window width */ + {0x80014, SWAP32(0x04000000)}, /* panel fb width (0x400=1024) */ + {0x80018, SWAP32(0x03000000)}, /* panel fb height (0x300=768) */ + {0x8001C, SWAP32(0x00000000)}, /* panel plane tl location */ + {0x80020, SWAP32(0x03000400)}, /* panel plane br location */ + {0x80024, SWAP32(0x053f03ff)}, /* panel horizontal total */ + {0x80028, SWAP32(0x0140040f)}, /* panel horizontal sync */ + {0x8002C, SWAP32(0x032502ff)}, /* panel vertical total */ + {0x80030, SWAP32(0x00260301)}, /* panel vertical sync */ + {0x80200, SWAP32(0x00010000)}, /* crt display control */ + {0, 0} +}; + +#endif /* CONFIG_VIDEO_SM501_32BPP */ + +#endif /* CONFIG_VIDEO_SM501 */ #if 0 #define FPGA_DEBUG @@ -92,7 +263,7 @@ unsigned char logo_bmp_1024[] = au_image_t au_image[] = { {"hh405/preinst.img", 0, -1, AU_SCRIPT}, {"hh405/u-boot.img", 0xfff80000, 0x00080000, AU_FIRMWARE}, - {"hh405/pImage_$(bd_type)", 0x00000000, 0x00100000, AU_NAND}, + {"hh405/pImage_${bd_type}", 0x00000000, 0x00100000, AU_NAND}, {"hh405/pImage.initrd", 0x00100000, 0x00200000, AU_NAND}, {"hh405/yaffsmt2.img", 0x00300000, 0x01c00000, AU_NAND}, {"hh405/postinst.img", 0, 0, AU_SCRIPT}, @@ -134,14 +305,15 @@ int board_revision(void) if (value & 0x80000000) { /* Revision 1.0 or 1.1 detected */ - return 1; + return 0x0101; } else { if (value & 0x00400000) { - /* Revision 1.3 detected */ - return 3; + /* unused */ + return 0x0103; } else { - /* Revision 1.2 detected */ - return 2; + /* Revision >= 2.0 detected */ + /* rev. 2.x uses four SM501 GPIOs for revision coding */ + return 0x0200; } } } @@ -261,10 +433,15 @@ int misc_init_r (void) * Write Board revision into FPGA */ *fpga_ctrl |= gd->board_type & 0x0003; - if (gd->board_type >= 2) { + if (gd->board_type >= 0x0200) { *fpga_ctrl |= CFG_FPGA_CTRL_CF_BUS_EN; } + /* + * Setup and enable EEPROM write protection + */ + out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP); + /* * Set NAND-FLASH GPIO signals to default */ @@ -301,6 +478,7 @@ int misc_init_r (void) /* * Init lcd interface and display logo */ + str = getenv("bd_type"); if (strcmp(str, "ppc230") == 0) { /* @@ -375,9 +553,29 @@ int misc_init_r (void) regs_13704_320_240_4bpp, sizeof(regs_13704_320_240_4bpp)/sizeof(regs_13704_320_240_4bpp[0]), logo_bmp_320, sizeof(logo_bmp_320)); +#ifdef CONFIG_VIDEO_SM501 } else { - printf("Unsupported bd_type defined (%s) -> No display configured!\n", str); - return 0; + pci_dev_t devbusfn; + + /* + * Is SM501 connected (ppc221/ppc231)? + */ + devbusfn = pci_find_device(PCI_VENDOR_SM, PCI_DEVICE_SM501, 0); + if (devbusfn != -1) { + puts("VGA: SM501 with 8 MB "); + if (strcmp(str, "ppc221") == 0) { + printf("(800*600, %dbpp)\n", BPP); + } else if (strcmp(str, "ppc231") == 0) { + printf("(1024*768, %dbpp)\n", BPP); + } else { + printf("Unsupported bd_type defined (%s) -> No display configured!\n", str); + return 0; + } + } else { + printf("Unsupported bd_type defined (%s) -> No display configured!\n", str); + return 0; + } +#endif /* CONFIG_VIDEO_SM501 */ } return (0); @@ -392,7 +590,7 @@ int checkboard (void) { DECLARE_GLOBAL_DATA_PTR; - unsigned char str[64]; + char str[64]; int i = getenv_r ("serial#", str, sizeof(str)); puts ("Board: "); @@ -410,7 +608,9 @@ int checkboard (void) } gd->board_type = board_revision(); - printf(", Rev 1.%ld)\n", gd->board_type); + printf(", Rev %ld.%ld)\n", + (gd->board_type >> 8) & 0xff, + gd->board_type & 0xff); /* * Disable sleep mode in LXT971 @@ -420,7 +620,6 @@ int checkboard (void) return 0; } -/* ------------------------------------------------------------------------- */ long int initdram (int board_type) { @@ -437,7 +636,6 @@ long int initdram (int board_type) return (4*1024*1024 << ((val & 0x000e0000) >> 17)); } -/* ------------------------------------------------------------------------- */ int testdram (void) { @@ -447,7 +645,6 @@ int testdram (void) return (0); } -/* ------------------------------------------------------------------------- */ #ifdef CONFIG_IDE_RESET void ide_set_reset(int on) @@ -479,3 +676,202 @@ void nand_init(void) } } #endif + + +#if defined(CFG_EEPROM_WREN) +/* Input: <dev_addr> I2C address of EEPROM device to enable. + * <state> -1: deliver current state + * 0: disable write + * 1: enable write + * Returns: -1: wrong device address + * 0: dis-/en- able done + * 0/1: current state if <state> was -1. + */ +int eeprom_write_enable (unsigned dev_addr, int state) +{ + if (CFG_I2C_EEPROM_ADDR != dev_addr) { + return -1; + } else { + switch (state) { + case 1: + /* Enable write access, clear bit GPIO_SINT2. */ + out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_EEPROM_WP); + state = 0; + break; + case 0: + /* Disable write access, set bit GPIO_SINT2. */ + out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP); + state = 0; + break; + default: + /* Read current status back. */ + state = (0 == (in32(GPIO0_OR) & CFG_EEPROM_WP)); + break; + } + } + return state; +} + +int do_eep_wren (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + int query = argc == 1; + int state = 0; + + if (query) { + /* Query write access state. */ + state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, -1); + if (state < 0) { + puts ("Query of write access state failed.\n"); + } else { + printf ("Write access for device 0x%0x is %sabled.\n", + CFG_I2C_EEPROM_ADDR, state ? "en" : "dis"); + state = 0; + } + } else { + if ('0' == argv[1][0]) { + /* Disable write access. */ + state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, 0); + } else { + /* Enable write access. */ + state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, 1); + } + if (state < 0) { + puts ("Setup of write access state failed.\n"); + } + } + + return state; +} + +U_BOOT_CMD(eepwren, 2, 0, do_eep_wren, + "eepwren - Enable / disable / query EEPROM write access\n", + NULL); +#endif /* #if defined(CFG_EEPROM_WREN) */ + + +#ifdef CONFIG_VIDEO_SM501 +#ifdef CONFIG_CONSOLE_EXTRA_INFO +/* + * Return text to be printed besides the logo. + */ +void video_get_info_str (int line_number, char *info) +{ + DECLARE_GLOBAL_DATA_PTR; + + char str[64]; + char str2[64]; + int i = getenv_r("serial#", str2, sizeof(str)); + + if (line_number == 1) { + sprintf(str, " Board: "); + + if (i == -1) { + strcat(str, "### No HW ID - assuming HH405"); + } else { + strcat(str, str2); + } + + if (getenv_r("bd_type", str2, sizeof(str2)) != -1) { + strcat(str, " ("); + strcat(str, str2); + } else { + strcat(str, " (Missing bd_type!"); + } + + sprintf(str2, ", Rev %ld.%ld)", + (gd->board_type >> 8) & 0xff, gd->board_type & 0xff); + strcat(str, str2); + strcpy(info, str); + } else { + info [0] = '\0'; + } +} +#endif /* CONFIG_CONSOLE_EXTRA_INFO */ + +/* + * Returns SM501 register base address. First thing called in the driver. + */ +unsigned int board_video_init (void) +{ + pci_dev_t devbusfn; + u32 addr; + + /* + * Is SM501 connected (ppc221/ppc231)? + */ + devbusfn = pci_find_device(PCI_VENDOR_SM, PCI_DEVICE_SM501, 0); + if (devbusfn != -1) { + pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_1, (u32 *)&addr); + return (addr & 0xfffffffe); + } + + return 0; +} + +/* + * Returns SM501 framebuffer address + */ +unsigned int board_video_get_fb (void) +{ + pci_dev_t devbusfn; + u32 addr; + + /* + * Is SM501 connected (ppc221/ppc231)? + */ + devbusfn = pci_find_device(PCI_VENDOR_SM, PCI_DEVICE_SM501, 0); + if (devbusfn != -1) { + pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_0, (u32 *)&addr); + return (addr & 0xfffffffe); + } + + return 0; +} + +/* + * Called after initializing the SM501 and before clearing the screen. + */ +void board_validate_screen (unsigned int base) +{ +} + +/* + * Return a pointer to the initialization sequence. + */ +const SMI_REGS *board_get_regs (void) +{ + char *str; + + str = getenv("bd_type"); + if (strcmp(str, "ppc221") == 0) { + return init_regs_800x600; + } else { + return init_regs_1024x768; + } +} + +int board_get_width (void) +{ + char *str; + + str = getenv("bd_type"); + if (strcmp(str, "ppc221") == 0) { + return 800; + } else { + return 1024; + } +} + +int board_get_height (void) +{ + char *str; + + str = getenv("bd_type"); + if (strcmp(str, "ppc221") == 0) { + return 600; + } else { + return 768; + } +} + +#endif /* CONFIG_VIDEO_SM501 */ |
