diff options
Diffstat (limited to 'board/amcc/yellowstone/yellowstone.c')
| -rw-r--r-- | board/amcc/yellowstone/yellowstone.c | 549 |
1 files changed, 0 insertions, 549 deletions
diff --git a/board/amcc/yellowstone/yellowstone.c b/board/amcc/yellowstone/yellowstone.c deleted file mode 100644 index 04f58e0419..0000000000 --- a/board/amcc/yellowstone/yellowstone.c +++ /dev/null @@ -1,549 +0,0 @@ -/* - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <common.h> -#include <ppc4xx.h> -#include <asm/processor.h> -#include <spd_sdram.h> - -DECLARE_GLOBAL_DATA_PTR; - -extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ - -int board_early_init_f(void) -{ - register uint reg; - - /*-------------------------------------------------------------------- - * Setup the external bus controller/chip selects - *-------------------------------------------------------------------*/ - mtdcr(ebccfga, xbcfg); - reg = mfdcr(ebccfgd); - mtdcr(ebccfgd, reg | 0x04000000); /* Set ATC */ - - /*-------------------------------------------------------------------- - * Setup the GPIO pins - *-------------------------------------------------------------------*/ - /*CPLD cs */ - /*setup Address lines for flash size 64Meg. */ - out32(GPIO0_OSRL, in32(GPIO0_OSRL) | 0x50010000); - out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x50010000); - out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x50000000); - - /*setup emac */ - out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xC080); - out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x40); - out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x55); - out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0x50004000); - out32(GPIO0_ISR1H, in32(GPIO0_ISR1H) | 0x00440000); - - /*UART1 */ - out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x02000000); - out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x00080000); - out32(GPIO1_ISR2L, in32(GPIO1_ISR2L) | 0x00010000); - - /* external interrupts IRQ0...3 */ - out32(GPIO1_TCR, in32(GPIO1_TCR) & ~0x00f00000); - out32(GPIO1_TSRL, in32(GPIO1_TSRL) & ~0x0000ff00); - out32(GPIO1_ISR1L, in32(GPIO1_ISR1L) | 0x00005500); - -#if 0 /* test-only */ - /*setup USB 2.0 */ - out32(GPIO1_TCR, in32(GPIO1_TCR) | 0xc0000000); - out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x50000000); - out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xf); - out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0xaa); - out32(GPIO0_ISR2H, in32(GPIO0_ISR2H) | 0x00000500); -#endif - - /*-------------------------------------------------------------------- - * Setup the interrupt controller polarities, triggers, etc. - *-------------------------------------------------------------------*/ - mtdcr(uic0sr, 0xffffffff); /* clear all */ - mtdcr(uic0er, 0x00000000); /* disable all */ - mtdcr(uic0cr, 0x00000009); /* ATI & UIC1 crit are critical */ - mtdcr(uic0pr, 0xfffffe13); /* per ref-board manual */ - mtdcr(uic0tr, 0x01c00008); /* per ref-board manual */ - mtdcr(uic0vr, 0x00000001); /* int31 highest, base=0x000 */ - mtdcr(uic0sr, 0xffffffff); /* clear all */ - - mtdcr(uic1sr, 0xffffffff); /* clear all */ - mtdcr(uic1er, 0x00000000); /* disable all */ - mtdcr(uic1cr, 0x00000000); /* all non-critical */ - mtdcr(uic1pr, 0xffffe0ff); /* per ref-board manual */ - mtdcr(uic1tr, 0x00ffc000); /* per ref-board manual */ - mtdcr(uic1vr, 0x00000001); /* int31 highest, base=0x000 */ - mtdcr(uic1sr, 0xffffffff); /* clear all */ - - /*-------------------------------------------------------------------- - * Setup other serial configuration - *-------------------------------------------------------------------*/ - mfsdr(sdr_pci0, reg); - mtsdr(sdr_pci0, 0x80000000 | reg); /* PCI arbiter enabled */ - mtsdr(sdr_pfc0, 0x00003e00); /* Pin function */ - mtsdr(sdr_pfc1, 0x00048000); /* Pin function: UART0 has 4 pins */ - - /*clear tmrclk divisor */ - *(unsigned char *)(CFG_BCSR_BASE | 0x04) = 0x00; - - /*enable ethernet */ - *(unsigned char *)(CFG_BCSR_BASE | 0x08) = 0xf0; - -#if 0 /* test-only */ - /*enable usb 1.1 fs device and remove usb 2.0 reset */ - *(unsigned char *)(CFG_BCSR_BASE | 0x09) = 0x00; -#endif - - /*get rid of flash write protect */ - *(unsigned char *)(CFG_BCSR_BASE | 0x07) = 0x00; - - return 0; -} - -int misc_init_r (void) -{ - uint pbcr; - int size_val = 0; - - /* Re-do sizing to get full correct info */ - mtdcr(ebccfga, pb0cr); - pbcr = mfdcr(ebccfgd); - switch (gd->bd->bi_flashsize) { - case 1 << 20: - size_val = 0; - break; - case 2 << 20: - size_val = 1; - break; - case 4 << 20: - size_val = 2; - break; - case 8 << 20: - size_val = 3; - break; - case 16 << 20: - size_val = 4; - break; - case 32 << 20: - size_val = 5; - break; - case 64 << 20: - size_val = 6; - break; - case 128 << 20: - size_val = 7; - break; - } - pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17); - mtdcr(ebccfga, pb0cr); - mtdcr(ebccfgd, pbcr); - - /* adjust flash start and offset */ - gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize; - gd->bd->bi_flashoffset = 0; - - /* Monitor protection ON by default */ - (void)flash_protect(FLAG_PROTECT_SET, - -CFG_MONITOR_LEN, - 0xffffffff, - &flash_info[0]); - - return 0; -} - -int checkboard(void) -{ - char *s = getenv("serial#"); - u8 rev; - u8 val; - - printf("Board: Yellowstone - AMCC PPC440GR Evaluation Board"); - - rev = *(u8 *)(CFG_CPLD + 0); - val = *(u8 *)(CFG_CPLD + 5) & 0x01; - printf(", Rev. %X, PCI=%d MHz", rev, val ? 66 : 33); - - if (s != NULL) { - puts(", serial# "); - puts(s); - } - putc('\n'); - - return (0); -} - -/************************************************************************* - * sdram_init -- doesn't use serial presence detect. - * - * Assumes: 256 MB, ECC, non-registered - * PLB @ 133 MHz - * - ************************************************************************/ -#define NUM_TRIES 64 -#define NUM_READS 10 - -void sdram_tr1_set(int ram_address, int* tr1_value) -{ - int i; - int j, k; - volatile unsigned int* ram_pointer = (unsigned int*)ram_address; - int first_good = -1, last_bad = 0x1ff; - - unsigned long test[NUM_TRIES] = { - 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF, - 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000, - 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000, - 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555, - 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555, - 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA, - 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA, - 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A, - 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A, - 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5, - 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5, - 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA, - 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA, - 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55, - 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55 }; - - /* go through all possible SDRAM0_TR1[RDCT] values */ - for (i=0; i<=0x1ff; i++) { - /* set the current value for TR1 */ - mtsdram(mem_tr1, (0x80800800 | i)); - - /* write values */ - for (j=0; j<NUM_TRIES; j++) { - ram_pointer[j] = test[j]; - - /* clear any cache at ram location */ - __asm__("dcbf 0,%0": :"r" (&ram_pointer[j])); - } - - /* read values back */ - for (j=0; j<NUM_TRIES; j++) { - for (k=0; k<NUM_READS; k++) { - /* clear any cache at ram location */ - __asm__("dcbf 0,%0": :"r" (&ram_pointer[j])); - - if (ram_pointer[j] != test[j]) - break; - } - - /* read error */ - if (k != NUM_READS) { - break; - } - } - - /* we have a SDRAM0_TR1[RDCT] that is part of the window */ - if (j == NUM_TRIES) { - if (first_good == -1) - first_good = i; /* found beginning of window */ - } else { /* bad read */ - /* if we have not had a good read then don't care */ - if(first_good != -1) { - /* first failure after a good read */ - last_bad = i-1; - break; - } - } - } - - /* return the current value for TR1 */ - *tr1_value = (first_good + last_bad) / 2; -} - -void sdram_init(void) -{ - register uint reg; - int tr1_bank1, tr1_bank2; - - /*-------------------------------------------------------------------- - * Setup some default - *------------------------------------------------------------------*/ - mtsdram(mem_uabba, 0x00000000); /* ubba=0 (default) */ - mtsdram(mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */ - mtsdram(mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */ - mtsdram(mem_clktr, 0x40000000); /* ?? */ - mtsdram(mem_wddctr, 0x40000000); /* ?? */ - - /*clear this first, if the DDR is enabled by a debugger - then you can not make changes. */ - mtsdram(mem_cfg0, 0x00000000); /* Disable EEC */ - - /*-------------------------------------------------------------------- - * Setup for board-specific specific mem - *------------------------------------------------------------------*/ - /* - * Following for CAS Latency = 2.5 @ 133 MHz PLB - */ - mtsdram(mem_b0cr, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */ - mtsdram(mem_b1cr, 0x080a4001); /* SDBA=0x080 128MB, Mode 3, enabled */ - - mtsdram(mem_tr0, 0x410a4012); /* ?? */ - mtsdram(mem_rtr, 0x04080000); /* ?? */ - mtsdram(mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM */ - mtsdram(mem_cfg0, 0x30000000); /* Disable EEC */ - udelay(400); /* Delay 200 usecs (min) */ - - /*-------------------------------------------------------------------- - * Enable the controller, then wait for DCEN to complete - *------------------------------------------------------------------*/ - mtsdram(mem_cfg0, 0x80000000); /* Enable */ - - for (;;) { - mfsdram(mem_mcsts, reg); - if (reg & 0x80000000) - break; - } - - sdram_tr1_set(0x00000000, &tr1_bank1); - sdram_tr1_set(0x08000000, &tr1_bank2); - mtsdram(mem_tr1, (((tr1_bank1+tr1_bank2)/2) | 0x80800800) ); -} - -/************************************************************************* - * long int initdram - * - ************************************************************************/ -long int initdram(int board) -{ - sdram_init(); - return CFG_SDRAM_BANKS * (CFG_KBYTES_SDRAM * 1024); /* return bytes */ -} - -#if defined(CFG_DRAM_TEST) -int testdram(void) -{ - unsigned long *mem = (unsigned long *)0; - const unsigned long kend = (1024 / sizeof(unsigned long)); - unsigned long k, n; - - mtmsr(0); - - for (k = 0; k < CFG_KBYTES_SDRAM; - ++k, mem += (1024 / sizeof(unsigned long))) { - if ((k & 1023) == 0) { - printf("%3d MB\r", k / 1024); - } - - memset(mem, 0xaaaaaaaa, 1024); - for (n = 0; n < kend; ++n) { - if (mem[n] != 0xaaaaaaaa) { - printf("SDRAM test fails at: %08x\n", - (uint) & mem[n]); - return 1; - } - } - - memset(mem, 0x55555555, 1024); - for (n = 0; n < kend; ++n) { - if (mem[n] != 0x55555555) { - printf("SDRAM test fails at: %08x\n", - (uint) & mem[n]); - return 1; - } - } - } - printf("SDRAM test passes\n"); - return 0; -} -#endif - -/************************************************************************* - * pci_pre_init - * - * This routine is called just prior to registering the hose and gives - * the board the opportunity to check things. Returning a value of zero - * indicates that things are bad & PCI initialization should be aborted. - * - * Different boards may wish to customize the pci controller structure - * (add regions, override default access routines, etc) or perform - * certain pre-initialization actions. - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) -int pci_pre_init(struct pci_controller *hose) -{ - unsigned long addr; - - /*-------------------------------------------------------------------------+ - | Set priority for all PLB3 devices to 0. - | Set PLB3 arbiter to fair mode. - +-------------------------------------------------------------------------*/ - mfsdr(sdr_amp1, addr); - mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00); - addr = mfdcr(plb3_acr); - mtdcr(plb3_acr, addr | 0x80000000); - - /*-------------------------------------------------------------------------+ - | Set priority for all PLB4 devices to 0. - +-------------------------------------------------------------------------*/ - mfsdr(sdr_amp0, addr); - mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00); - addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */ - mtdcr(plb4_acr, addr); - - /*-------------------------------------------------------------------------+ - | Set Nebula PLB4 arbiter to fair mode. - +-------------------------------------------------------------------------*/ - /* Segment0 */ - addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair; - addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled; - addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep; - addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep; - mtdcr(plb0_acr, addr); - - /* Segment1 */ - addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair; - addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled; - addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep; - addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep; - mtdcr(plb1_acr, addr); - - return 1; -} -#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */ - -/************************************************************************* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller *hose) -{ - /*--------------------------------------------------------------------------+ - * Set up Direct MMIO registers - *--------------------------------------------------------------------------*/ - /*--------------------------------------------------------------------------+ - | PowerPC440 EP PCI Master configuration. - | Map one 1Gig range of PLB/processor addresses to PCI memory space. - | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF - | Use byte reversed out routines to handle endianess. - | Make this region non-prefetchable. - +--------------------------------------------------------------------------*/ - out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */ - out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE); /* PMM0 Local Address */ - out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE); /* PMM0 PCI Low Address */ - out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */ - out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */ - - out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */ - out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2); /* PMM0 Local Address */ - out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2); /* PMM0 PCI Low Address */ - out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */ - out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */ - - out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */ - out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */ - out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */ - out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */ - - /*--------------------------------------------------------------------------+ - * Set up Configuration registers - *--------------------------------------------------------------------------*/ - - /* Program the board's subsystem id/vendor id */ - pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID, - CFG_PCI_SUBSYS_VENDORID); - pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID); - - /* Configure command register as bus master */ - pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER); - - /* 240nS PCI clock */ - pci_write_config_word(0, PCI_LATENCY_TIMER, 1); - - /* No error reporting */ - pci_write_config_word(0, PCI_ERREN, 0); - - pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101); - -} -#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */ - -/************************************************************************* - * pci_master_init - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) -void pci_master_init(struct pci_controller *hose) -{ - unsigned short temp_short; - - /*--------------------------------------------------------------------------+ - | Write the PowerPC440 EP PCI Configuration regs. - | Enable PowerPC440 EP to be a master on the PCI bus (PMM). - | Enable PowerPC440 EP to act as a PCI memory target (PTM). - +--------------------------------------------------------------------------*/ - pci_read_config_word(0, PCI_COMMAND, &temp_short); - pci_write_config_word(0, PCI_COMMAND, - temp_short | PCI_COMMAND_MASTER | - PCI_COMMAND_MEMORY); -} -#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) */ - -/************************************************************************* - * is_pci_host - * - * This routine is called to determine if a pci scan should be - * performed. With various hardware environments (especially cPCI and - * PPMC) it's insufficient to depend on the state of the arbiter enable - * bit in the strap register, or generic host/adapter assumptions. - * - * Rather than hard-code a bad assumption in the general 440 code, the - * 440 pci code requires the board to decide at runtime. - * - * Return 0 for adapter mode, non-zero for host (monarch) mode. - * - * - ************************************************************************/ -#if defined(CONFIG_PCI) -int is_pci_host(struct pci_controller *hose) -{ - /* Bamboo is always configured as host. */ - return (1); -} -#endif /* defined(CONFIG_PCI) */ - -/************************************************************************* - * hw_watchdog_reset - * - * This routine is called to reset (keep alive) the watchdog timer - * - ************************************************************************/ -#if defined(CONFIG_HW_WATCHDOG) -void hw_watchdog_reset(void) -{ - -} -#endif - -void board_reset(void) -{ - /* give reset to BCSR */ - *(unsigned char *)(CFG_BCSR_BASE | 0x06) = 0x09; -} |
