diff options
Diffstat (limited to 'board/BuR/brppt1/board.c')
| -rw-r--r-- | board/BuR/brppt1/board.c | 174 |
1 files changed, 174 insertions, 0 deletions
diff --git a/board/BuR/brppt1/board.c b/board/BuR/brppt1/board.c new file mode 100644 index 0000000000..a22722122b --- /dev/null +++ b/board/BuR/brppt1/board.c @@ -0,0 +1,174 @@ +/* + * board.c + * + * Board functions for B&R BRPPT1 + * + * Copyright (C) 2013 Hannes Schmelzer <oe5hpm@oevsv.at> + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + * + */ + +#include <common.h> +#include <errno.h> +#include <spl.h> +#include <asm/arch/cpu.h> +#include <asm/arch/hardware.h> +#include <asm/arch/omap.h> +#include <asm/arch/ddr_defs.h> +#include <asm/arch/clock.h> +#include <asm/arch/gpio.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/mem.h> +#include <asm/io.h> +#include <asm/emif.h> +#include <asm/gpio.h> +#include <i2c.h> +#include <power/tps65217.h> +#include "../common/bur_common.h" +#include <lcd.h> +#include <watchdog.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* --------------------------------------------------------------------------*/ +/* -- defines for GPIO -- */ +#define REPSWITCH (0+20) /* GPIO0_20 */ + +#if defined(CONFIG_SPL_BUILD) +/* TODO: check ram-timing ! */ +static const struct ddr_data ddr3_data = { + .datardsratio0 = MT41K256M16HA125E_RD_DQS, + .datawdsratio0 = MT41K256M16HA125E_WR_DQS, + .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE, + .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA, +}; + +static const struct cmd_control ddr3_cmd_ctrl_data = { + .cmd0csratio = MT41K256M16HA125E_RATIO, + .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT, + + .cmd1csratio = MT41K256M16HA125E_RATIO, + .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT, + + .cmd2csratio = MT41K256M16HA125E_RATIO, + .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT, +}; + +static struct emif_regs ddr3_emif_reg_data = { + .sdram_config = MT41K256M16HA125E_EMIF_SDCFG, + .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF, + .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1, + .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2, + .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3, + .zq_config = MT41K256M16HA125E_ZQ_CFG, + .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY, +}; + +static const struct ctrl_ioregs ddr3_ioregs = { + .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, + .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, + .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE, + .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, + .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, +}; + +#ifdef CONFIG_SPL_OS_BOOT +/* + * called from spl_nand.c + * return 0 for loading linux, return 1 for loading u-boot + */ +int spl_start_uboot(void) +{ + if (0 == gpio_get_value(REPSWITCH)) { + mdelay(1000); + printf("SPL: entering u-boot instead kernel image.\n"); + return 1; + } + return 0; +} +#endif /* CONFIG_SPL_OS_BOOT */ + +#define OSC (V_OSCK/1000000) +static const struct dpll_params dpll_ddr3 = { 400, OSC-1, 1, -1, -1, -1, -1}; + +void am33xx_spl_board_init(void) +{ + struct cm_perpll *const cmper = (struct cm_perpll *)CM_PER; + /*struct cm_wkuppll *const cmwkup = (struct cm_wkuppll *)CM_WKUP;*/ + struct cm_dpll *const cmdpll = (struct cm_dpll *)CM_DPLL; + + /* + * in TRM they write a reset value of 1 (=CLK_M_OSC) for the + * CLKSEL_TIMER6_CLK Register, in fact reset value is 0, so we need set + * the source of timer6 clk to CLK_M_OSC + */ + writel(0x01, &cmdpll->clktimer6clk); + + /* enable additional clocks of modules which are accessed later */ + u32 *const clk_domains[] = { + &cmper->lcdcclkstctrl, + 0 + }; + + u32 *const clk_modules_tsspecific[] = { + &cmper->lcdclkctrl, + &cmper->timer5clkctrl, + &cmper->timer6clkctrl, + 0 + }; + do_enable_clocks(clk_domains, clk_modules_tsspecific, 1); + + /* setup LCD-Pixel Clock */ + writel(0x2, &cmdpll->clklcdcpixelclk); /* clock comes from perPLL M2 */ + + /* setup I2C */ + enable_i2c_pin_mux(); + i2c_set_bus_num(0); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); + pmicsetup(0); + + gpio_direction_output(64+29, 1); /* switch NAND_RnB to GPMC_WAIT1 */ + gpio_direction_output(64+28, 1); /* switch MII2_CRS to GPMC_WAIT0 */ +} + +const struct dpll_params *get_dpll_ddr_params(void) +{ + return &dpll_ddr3; +} + +void sdram_init(void) +{ + config_ddr(400, &ddr3_ioregs, + &ddr3_data, + &ddr3_cmd_ctrl_data, + &ddr3_emif_reg_data, 0); +} +#endif /* CONFIG_SPL_BUILD */ + +/* Basic board specific setup. Pinmux has been handled already. */ +int board_init(void) +{ +#if defined(CONFIG_HW_WATCHDOG) + hw_watchdog_init(); +#endif + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; +#ifdef CONFIG_NAND + gpmc_init(); +#endif + return 0; +} + +#ifdef CONFIG_BOARD_LATE_INIT +int board_late_init(void) +{ + if (0 == gpio_get_value(REPSWITCH)) { + lcd_position_cursor(1, 8); + lcd_puts( + "switching to network-console ... "); + setenv("bootcmd", "run netconsole"); + } + return 0; +} +#endif /* CONFIG_BOARD_LATE_INIT */ |
