diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 16 |
1 files changed, 8 insertions, 8 deletions
@@ -183,7 +183,7 @@ Directory Hierarchy: /nios2 Files generic to Altera NIOS2 architecture /cpu CPU specific files /lib Architecture specific library files - /ppc Files generic to PowerPC architecture + /powerpc Files generic to PowerPC architecture /cpu CPU specific files /74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs /mpc5xx Files specific to Freescale MPC5xx CPUs @@ -1417,7 +1417,7 @@ The following options need to be configured: the CPU's i2c node address). Now, the u-boot i2c code for the mpc8xx - (arch/ppc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node + (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node and so its address should therefore be cleared to 0 (See, eg, MPC823e User's Manual p.16-473). So, set CONFIG_SYS_I2C_SLAVE to 0. @@ -1966,7 +1966,7 @@ Legacy uImage format: 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS - -30 arch/ppc/lib/board.c Fatal error, hang the system + -30 arch/powerpc/lib/board.c Fatal error, hang the system -31 post/post.c POST test failed, detected by post_output_backlog() -32 post/post.c POST test failed, detected by post_run_single() @@ -2727,7 +2727,7 @@ Low Level (hardware related) configuration options: CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL, CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE, CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only) - Overrides the default PCI memory map in arch/ppc/cpu/mpc8260/pci.c if set. + Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set. - CONFIG_PCI_DISABLE_PCIE: Disable PCI-Express on systems where it is supported but not @@ -3373,7 +3373,7 @@ configure the Linux device drivers for use with your target hardware (no, we don't intend to provide a full virtual machine interface to Linux :-). -But now you can ignore ALL boot loader code (in arch/ppc/mbxboot). +But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot). Just make sure your machine specific header file (for instance include/asm-ppc/tqm8xx.h) includes the same definition of the Board @@ -3471,7 +3471,7 @@ So a typical call to build a U-Boot image would read: -> tools/mkimage -n '2.4.4 kernel for TQM850L' \ > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \ - > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \ + > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \ > examples/uImage.TQM850L Image Name: 2.4.4 kernel for TQM850L Created: Wed Jul 19 02:34:59 2000 @@ -3495,10 +3495,10 @@ speed for memory and install an UNCOMPRESSED image instead: this needs more space in Flash, but boots much faster since it does not need to be uncompressed: - -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz + -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz -> tools/mkimage -n '2.4.4 kernel for TQM850L' \ > -A ppc -O linux -T kernel -C none -a 0 -e 0 \ - > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \ + > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \ > examples/uImage.TQM850L-uncompressed Image Name: 2.4.4 kernel for TQM850L Created: Wed Jul 19 02:34:59 2000 |
