diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 104 |
1 files changed, 104 insertions, 0 deletions
@@ -2288,6 +2288,21 @@ CBFS (Coreboot Filesystem) support 9 i2c buses for Exynos4 and 1 for S3C24X0 SoCs from Samsung) with a fix speed from 100000 and the slave addr 0! + - drivers/i2c/ihs_i2c.c + - activate this driver with CONFIG_SYS_I2C_IHS + - CONFIG_SYS_I2C_IHS_CH0 activate hardware channel 0 + - CONFIG_SYS_I2C_IHS_SPEED_0 speed channel 0 + - CONFIG_SYS_I2C_IHS_SLAVE_0 slave addr channel 0 + - CONFIG_SYS_I2C_IHS_CH1 activate hardware channel 1 + - CONFIG_SYS_I2C_IHS_SPEED_1 speed channel 1 + - CONFIG_SYS_I2C_IHS_SLAVE_1 slave addr channel 1 + - CONFIG_SYS_I2C_IHS_CH2 activate hardware channel 2 + - CONFIG_SYS_I2C_IHS_SPEED_2 speed channel 2 + - CONFIG_SYS_I2C_IHS_SLAVE_2 slave addr channel 2 + - CONFIG_SYS_I2C_IHS_CH3 activate hardware channel 3 + - CONFIG_SYS_I2C_IHS_SPEED_3 speed channel 3 + - CONFIG_SYS_I2C_IHS_SLAVE_3 slave addr channel 3 + additional defines: CONFIG_SYS_NUM_I2C_BUSES @@ -3254,6 +3269,11 @@ FIT uImage format: disabled. If a board need legacy image format support enable this through CONFIG_IMAGE_FORMAT_LEGACY + CONFIG_FIT_DISABLE_SHA256 + Supporting SHA256 hashes has quite an impact on binary size. + For constrained systems sha256 hash support can be disabled + with this option. + - Standalone program support: CONFIG_STANDALONE_LOAD_ADDR @@ -3716,6 +3736,22 @@ Configuration Settings: - CONFIG_SYS_MALLOC_LEN: Size of DRAM reserved for malloc() use. +- CONFIG_SYS_MALLOC_F_LEN + Size of the malloc() pool for use before relocation. If + this is defined, then a very simple malloc() implementation + will become available before relocation. The address is just + below the global data, and the stack is moved down to make + space. + + This feature allocates regions with increasing addresses + within the region. calloc() is supported, but realloc() + is not available. free() is supported but does nothing. + The memory will be freed (or in fact just forgotton) when + U-Boot relocates itself. + + Pre-relocation malloc() is only supported on sandbox + at present but is fairly easy to enable for other archs. + - CONFIG_SYS_BOOTM_LEN: Normally compressed uImages are limited to an uncompressed size of 8 MBytes. If this is not enough, @@ -4069,6 +4105,43 @@ to save the current settings. environment area within the total memory of your DataFlash placed at the specified address. +- CONFIG_ENV_IS_IN_SPI_FLASH: + + Define this if you have a SPI Flash memory device which you + want to use for the environment. + + - CONFIG_ENV_OFFSET: + - CONFIG_ENV_SIZE: + + These two #defines specify the offset and size of the + environment area within the SPI Flash. CONFIG_ENV_OFFSET must be + aligned to an erase sector boundary. + + - CONFIG_ENV_SECT_SIZE: + + Define the SPI flash's sector size. + + - CONFIG_ENV_OFFSET_REDUND (optional): + + This setting describes a second storage area of CONFIG_ENV_SIZE + size used to hold a redundant copy of the environment data, so + that there is a valid backup copy in case there is a power failure + during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be + aligned to an erase sector boundary. + + - CONFIG_ENV_SPI_BUS (optional): + - CONFIG_ENV_SPI_CS (optional): + + Define the SPI bus and chip select. If not defined they will be 0. + + - CONFIG_ENV_SPI_MAX_HZ (optional): + + Define the SPI max work clock. If not defined then use 1MHz. + + - CONFIG_ENV_SPI_MODE (optional): + + Define the SPI work mode. If not defined then use SPI_MODE_3. + - CONFIG_ENV_IS_IN_REMOTE: Define this if you have a remote memory space which you @@ -4156,6 +4229,37 @@ but it can not erase, write this NOR flash by SRIO or PCIE interface. You will probably want to define these to avoid a really noisy system when storing the env in UBI. +- CONFIG_ENV_IS_IN_FAT: + Define this if you want to use the FAT file system for the environment. + + - FAT_ENV_INTERFACE: + + Define this to a string that is the name of the block device. + + - FAT_ENV_DEV_AND_PART: + + Define this to a string to specify the partition of the device. It can + be as following: + + "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1) + - "D:P": device D partition P. Error occurs if device D has no + partition table. + - "D:0": device D. + - "D" or "D:": device D partition 1 if device D has partition + table, or the whole device D if has no partition + table. + - "D:auto": first partition in device D with bootable flag set. + If none, first valid paratition in device D. If no + partition table then means device D. + + - FAT_ENV_FILE: + + It's a string of the FAT file name. This file use to store the + envrionment. + + - CONFIG_FAT_WRITE: + This should be defined. Otherwise it cannot save the envrionment file. + - CONFIG_ENV_IS_IN_MMC: Define this if you have an MMC device which you want to use for the |
