diff options
307 files changed, 13194 insertions, 7254 deletions
@@ -901,7 +901,7 @@ MKIMAGEFLAGS_u-boot-spl.ais = -s -n $(if $(CONFIG_AIS_CONFIG_FILE), \ spl/u-boot-spl.ais: spl/u-boot-spl.bin FORCE $(call if_changed,mkimage) -OBJCOPYFLAGS_u-boot.ais = -I binary -O binary --pad-to=$(CONFIG_SPL_MAX_SIZE) +OBJCOPYFLAGS_u-boot.ais = -I binary -O binary --pad-to=$(CONFIG_SPL_PAD_TO) u-boot.ais: spl/u-boot-spl.ais u-boot.img FORCE $(call if_changed,pad_cat) @@ -1534,6 +1534,16 @@ The following options need to be configured: CONFIG_SH_MMCIF_CLK Define the clock frequency for MMCIF + CONFIG_GENERIC_MMC + Enable the generic MMC driver + + CONFIG_SUPPORT_EMMC_BOOT + Enable some additional features of the eMMC boot partitions. + + CONFIG_SUPPORT_EMMC_RPMB + Enable the commands for reading, writing and programming the + key for the Replay Protection Memory Block partition in eMMC. + - USB Device Firmware Update (DFU) class support: CONFIG_DFU_FUNCTION This enables the USB portion of the DFU USB class @@ -1579,6 +1589,28 @@ The following options need to be configured: entering dfuMANIFEST state. Host waits this timeout, before sending again an USB request to the device. +- USB Device Android Fastboot support: + CONFIG_CMD_FASTBOOT + This enables the command "fastboot" which enables the Android + fastboot mode for the platform's USB device. Fastboot is a USB + protocol for downloading images, flashing and device control + used on Android devices. + See doc/README.android-fastboot for more information. + + CONFIG_ANDROID_BOOT_IMAGE + This enables support for booting images which use the Android + image format header. + + CONFIG_USB_FASTBOOT_BUF_ADDR + The fastboot protocol requires a large memory buffer for + downloads. Define this to the starting RAM address to use for + downloaded images. + + CONFIG_USB_FASTBOOT_BUF_SIZE + The fastboot protocol requires a large memory buffer for + downloads. This buffer should be as large as possible for a + platform. Define this to the size available RAM for fastboot. + - Journaling Flash filesystem support: CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE, CONFIG_JFFS2_NAND_DEV @@ -2550,6 +2582,19 @@ CBFS (Coreboot Filesystem) support Specify the number of FPGA devices to support. + CONFIG_CMD_FPGA_LOADMK + + Enable support for fpga loadmk command + + CONFIG_CMD_FPGA_LOADP + + Enable support for fpga loadp command - load partial bitstream + + CONFIG_CMD_FPGA_LOADBP + + Enable support for fpga loadbp command - load partial bitstream + (Xilinx only) + CONFIG_SYS_FPGA_PROG_FEEDBACK Enable printing of hash marks during FPGA configuration. diff --git a/arch/arm/cpu/arm1136/start.S b/arch/arm/cpu/arm1136/start.S index 3e2358e132..1cfcca9fa6 100644 --- a/arch/arm/cpu/arm1136/start.S +++ b/arch/arm/cpu/arm1136/start.S @@ -15,48 +15,7 @@ #include <asm-offsets.h> #include <config.h> #include <version.h> -.globl _start -_start: b reset -#ifdef CONFIG_SPL_BUILD - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang -_hang: - .word do_hang - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 /* now 16*4=64 */ -#else - ldr pc, _undefined_instruction - ldr pc, _software_interrupt - ldr pc, _prefetch_abort - ldr pc, _data_abort - ldr pc, _not_used - ldr pc, _irq - ldr pc, _fiq - -_undefined_instruction: .word undefined_instruction -_software_interrupt: .word software_interrupt -_prefetch_abort: .word prefetch_abort -_data_abort: .word data_abort -_not_used: .word not_used -_irq: .word irq -_fiq: .word fiq -_pad: .word 0x12345678 /* now 16*4=64 */ -#endif /* CONFIG_SPL_BUILD */ -.global _end_vect -_end_vect: - - .balignl 16,0xdeadbeef /* ************************************************************************* * @@ -70,26 +29,7 @@ _end_vect: ************************************************************************* */ -#ifdef CONFIG_USE_IRQ -/* IRQ stack memory (calculated at run-time) */ -.globl IRQ_STACK_START -IRQ_STACK_START: - .word 0x0badc0de - -/* IRQ stack memory (calculated at run-time) */ -.globl FIQ_STACK_START -FIQ_STACK_START: - .word 0x0badc0de -#endif - -/* IRQ stack memory (calculated at run-time) + 8 bytes */ -.globl IRQ_STACK_START_IN -IRQ_STACK_START_IN: - .word 0x0badc0de - -/* - * the actual reset code - */ + .globl reset reset: /* @@ -152,195 +92,3 @@ cpu_init_crit: mov lr, ip /* restore link */ mov pc, lr /* back to my caller */ #endif /* CONFIG_SKIP_LOWLEVEL_INIT */ - -#ifndef CONFIG_SPL_BUILD -/* - ************************************************************************* - * - * Interrupt handling - * - ************************************************************************* - */ -@ -@ IRQ stack frame. -@ -#define S_FRAME_SIZE 72 - -#define S_OLD_R0 68 -#define S_PSR 64 -#define S_PC 60 -#define S_LR 56 -#define S_SP 52 - -#define S_IP 48 -#define S_FP 44 -#define S_R10 40 -#define S_R9 36 -#define S_R8 32 -#define S_R7 28 -#define S_R6 24 -#define S_R5 20 -#define S_R4 16 -#define S_R3 12 -#define S_R2 8 -#define S_R1 4 -#define S_R0 0 - -#define MODE_SVC 0x13 -#define I_BIT 0x80 - -/* - * use bad_save_user_regs for abort/prefetch/undef/swi ... - * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling - */ - - .macro bad_save_user_regs - sub sp, sp, #S_FRAME_SIZE @ carve out a frame on current user stack - stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12 - - ldr r2, IRQ_STACK_START_IN @ set base 2 words into abort stack - ldmia r2, {r2 - r3} @ get values for "aborted" pc and cpsr (into parm regs) - add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack - - add r5, sp, #S_SP - mov r1, lr - stmia r5, {r0 - r3} @ save sp_SVC, lr_SVC, pc, cpsr - mov r0, sp @ save current stack into r0 (param register) - .endm - - .macro irq_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - add r8, sp, #S_PC @ !!!! R8 NEEDS to be saved !!!! a reserved stack spot would be good. - stmdb r8, {sp, lr}^ @ Calling SP, LR - str lr, [r8, #0] @ Save calling PC - mrs r6, spsr - str r6, [r8, #4] @ Save CPSR - str r0, [r8, #8] @ Save OLD_R0 - mov r0, sp - .endm - - .macro irq_restore_user_regs - ldmia sp, {r0 - lr}^ @ Calling r0 - lr - mov r0, r0 - ldr lr, [sp, #S_PC] @ Get PC - add sp, sp, #S_FRAME_SIZE - subs pc, lr, #4 @ return & move spsr_svc into cpsr - .endm - - .macro get_bad_stack - ldr r13, IRQ_STACK_START_IN @ setup our mode stack (enter in banked mode) - - str lr, [r13] @ save caller lr in position 0 of saved stack - mrs lr, spsr @ get the spsr - str lr, [r13, #4] @ save spsr in position 1 of saved stack - - mov r13, #MODE_SVC @ prepare SVC-Mode - @ msr spsr_c, r13 - msr spsr, r13 @ switch modes, make sure moves will execute - mov lr, pc @ capture return pc - movs pc, lr @ jump to next instruction & switch modes. - .endm - - .macro get_bad_stack_swi - sub r13, r13, #4 @ space on current stack for scratch reg. - str r0, [r13] @ save R0's value. - ldr r0, IRQ_STACK_START_IN @ get data regions start - str lr, [r0] @ save caller lr in position 0 of saved stack - mrs lr, spsr @ get the spsr - str lr, [r0, #4] @ save spsr in position 1 of saved stack - ldr lr, [r0] @ restore lr - ldr r0, [r13] @ restore r0 - add r13, r13, #4 @ pop stack entry - .endm - - .macro get_irq_stack @ setup IRQ stack - ldr sp, IRQ_STACK_START - .endm - - .macro get_fiq_stack @ setup FIQ stack - ldr sp, FIQ_STACK_START - .endm -#endif /* CONFIG_SPL_BUILD */ - -/* - * exception handlers - */ -#ifdef CONFIG_SPL_BUILD - .align 5 -do_hang: - bl hang /* hang and never return */ -#else /* !CONFIG_SPL_BUILD */ - .align 5 -undefined_instruction: - get_bad_stack - bad_save_user_regs - bl do_undefined_instruction - - .align 5 -software_interrupt: - get_bad_stack_swi - bad_save_user_regs - bl do_software_interrupt - - .align 5 -prefetch_abort: - get_bad_stack - bad_save_user_regs - bl do_prefetch_abort - - .align 5 -data_abort: - get_bad_stack - bad_save_user_regs - bl do_data_abort - - .align 5 -not_used: - get_bad_stack - bad_save_user_regs - bl do_not_used - -#ifdef CONFIG_USE_IRQ - - .align 5 -irq: - get_irq_stack - irq_save_user_regs - bl do_irq - irq_restore_user_regs - - .align 5 -fiq: - get_fiq_stack - /* someone ought to write a more effiction fiq_save_user_regs */ - irq_save_user_regs - bl do_fiq - irq_restore_user_regs - -#else - - .align 5 -irq: - get_bad_stack - bad_save_user_regs - bl do_irq - - .align 5 -fiq: - get_bad_stack - bad_save_user_regs - bl do_fiq - -#endif - .align 5 -.global arm1136_cache_flush -arm1136_cache_flush: -#if !defined(CONFIG_SYS_ICACHE_OFF) - mcr p15, 0, r1, c7, c5, 0 @ invalidate I cache -#endif -#if !defined(CONFIG_SYS_DCACHE_OFF) - mcr p15, 0, r1, c7, c14, 0 @ invalidate D cache -#endif - mov pc, lr @ back to caller -#endif /* CONFIG_SPL_BUILD */ diff --git a/arch/arm/cpu/arm1176/start.S b/arch/arm/cpu/arm1176/start.S index ce620115d4..0704bdde27 100644 --- a/arch/arm/cpu/arm1176/start.S +++ b/arch/arm/cpu/arm1176/start.S @@ -25,48 +25,6 @@ /* ************************************************************************* * - * Jump vector table as in table 3.1 in [1] - * - ************************************************************************* - */ - -.globl _start -_start: b reset -#ifndef CONFIG_SPL_BUILD - ldr pc, _undefined_instruction - ldr pc, _software_interrupt - ldr pc, _prefetch_abort - ldr pc, _data_abort - ldr pc, _not_used - ldr pc, _irq - ldr pc, _fiq - -_undefined_instruction: - .word undefined_instruction -_software_interrupt: - .word software_interrupt -_prefetch_abort: - .word prefetch_abort -_data_abort: - .word data_abort -_not_used: - .word not_used -_irq: - .word irq -_fiq: - .word fiq -_pad: - .word 0x12345678 /* now 16*4=64 */ -#else - . = _start + 64 -#endif - -.global _end_vect -_end_vect: - .balignl 16,0xdeadbeef -/* - ************************************************************************* - * * Startup Code (reset vector) * * do important init only if we don't start from memory! @@ -77,14 +35,7 @@ _end_vect: ************************************************************************* */ -/* IRQ stack memory (calculated at run-time) + 8 bytes */ -.globl IRQ_STACK_START_IN -IRQ_STACK_START_IN: - .word 0x0badc0de - -/* - * the actual reset code - */ + .globl reset reset: /* @@ -182,150 +133,3 @@ skip_tcmdisable: c_runtime_cpu_setup: mov pc, lr - -#ifndef CONFIG_SPL_BUILD -/* - ************************************************************************* - * - * Interrupt handling - * - ************************************************************************* - */ -@ -@ IRQ stack frame. -@ -#define S_FRAME_SIZE 72 - -#define S_OLD_R0 68 -#define S_PSR 64 -#define S_PC 60 -#define S_LR 56 -#define S_SP 52 - -#define S_IP 48 -#define S_FP 44 -#define S_R10 40 -#define S_R9 36 -#define S_R8 32 -#define S_R7 28 -#define S_R6 24 -#define S_R5 20 -#define S_R4 16 -#define S_R3 12 -#define S_R2 8 -#define S_R1 4 -#define S_R0 0 - -#define MODE_SVC 0x13 -#define I_BIT 0x80 - -/* - * use bad_save_user_regs for abort/prefetch/undef/swi ... - */ - - .macro bad_save_user_regs - /* carve out a frame on current user stack */ - sub sp, sp, #S_FRAME_SIZE - /* Save user registers (now in svc mode) r0-r12 */ - stmia sp, {r0 - r12} - - ldr r2, IRQ_STACK_START_IN - /* get values for "aborted" pc and cpsr (into parm regs) */ - ldmia r2, {r2 - r3} - /* grab pointer to old stack */ - add r0, sp, #S_FRAME_SIZE - - add r5, sp, #S_SP - mov r1, lr - /* save sp_SVC, lr_SVC, pc, cpsr */ - stmia r5, {r0 - r3} - /* save current stack into r0 (param register) */ - mov r0, sp - .endm - - .macro get_bad_stack - ldr r13, IRQ_STACK_START_IN @ setup our mode stack - - /* save caller lr in position 0 of saved stack */ - str lr, [r13] - /* get the spsr */ - mrs lr, spsr - /* save spsr in position 1 of saved stack */ - str lr, [r13, #4] - - /* prepare SVC-Mode */ - mov r13, #MODE_SVC - @ msr spsr_c, r13 - /* switch modes, make sure moves will execute */ - msr spsr, r13 - /* capture return pc */ - mov lr, pc - /* jump to next instruction & switch modes. */ - movs pc, lr - .endm - - .macro get_bad_stack_swi - /* space on current stack for scratch reg. */ - sub r13, r13, #4 - /* save R0's value. */ - str r0, [r13] - ldr r13, IRQ_STACK_START_IN @ setup our mode stack - /* save caller lr in position 0 of saved stack */ - str lr, [r0] - /* get the spsr */ - mrs lr, spsr - /* save spsr in position 1 of saved stack */ - str lr, [r0, #4] - /* restore lr */ - ldr lr, [r0] - /* restore r0 */ - ldr r0, [r13] - /* pop stack entry */ - add r13, r13, #4 - .endm - -/* - * exception handlers - */ - .align 5 -undefined_instruction: - get_bad_stack - bad_save_user_regs - bl do_undefined_instruction - - .align 5 -software_interrupt: - get_bad_stack_swi - bad_save_user_regs - bl do_software_interrupt - - .align 5 -prefetch_abort: - get_bad_stack - bad_save_user_regs - bl do_prefetch_abort - - .align 5 -data_abort: - get_bad_stack - bad_save_user_regs - bl do_data_abort - - .align 5 -not_used: - get_bad_stack - bad_save_user_regs - bl do_not_used - - .align 5 -irq: - get_bad_stack - bad_save_user_regs - bl do_irq - - .align 5 -fiq: - get_bad_stack - bad_save_user_regs - bl do_fiq -#endif /* CONFIG_SPL_BUILD */ diff --git a/arch/arm/cpu/arm720t/start.S b/arch/arm/cpu/arm720t/start.S index 1a34842690..01c85be64b 100644 --- a/arch/arm/cpu/arm720t/start.S +++ b/arch/arm/cpu/arm720t/start.S @@ -15,48 +15,6 @@ /* ************************************************************************* * - * Jump vector table as in table 3.1 in [1] - * - ************************************************************************* - */ - - -.globl _start -_start: b reset - ldr pc, _undefined_instruction - ldr pc, _software_interrupt - ldr pc, _prefetch_abort - ldr pc, _data_abort - ldr pc, _not_used - ldr pc, _irq - ldr pc, _fiq - -#ifdef CONFIG_SPL_BUILD -_undefined_instruction: .word _undefined_instruction -_software_interrupt: .word _software_interrupt -_prefetch_abort: .word _prefetch_abort -_data_abort: .word _data_abort -_not_used: .word _not_used -_irq: .word _irq -_fiq: .word _fiq -_pad: .word 0x12345678 /* now 16*4=64 */ -#else -_undefined_instruction: .word undefined_instruction -_software_interrupt: .word software_interrupt -_prefetch_abort: .word prefetch_abort -_data_abort: .word data_abort -_not_used: .word not_used -_irq: .word irq -_fiq: .word fiq -_pad: .word 0x12345678 /* now 16*4=64 */ -#endif /* CONFIG_SPL_BUILD */ - - .balignl 16,0xdeadbeef - - -/* - ************************************************************************* - * * Startup Code (reset vector) * * do important init only if we don't start from RAM! @@ -67,26 +25,7 @@ _pad: .word 0x12345678 /* now 16*4=64 */ ************************************************************************* */ -#ifdef CONFIG_USE_IRQ -/* IRQ stack memory (calculated at run-time) */ -.globl IRQ_STACK_START -IRQ_STACK_START: - .word 0x0badc0de - -/* IRQ stack memory (calculated at run-time) */ -.globl FIQ_STACK_START -FIQ_STACK_START: - .word 0x0badc0de -#endif - -/* IRQ stack memory (calculated at run-time) + 8 bytes */ -.globl IRQ_STACK_START_IN -IRQ_STACK_START_IN: - .word 0x0badc0de - -/* - * the actual reset code - */ + .globl reset reset: /* @@ -139,169 +78,3 @@ cpu_init_crit: mov pc, lr #endif /* CONFIG_SKIP_LOWLEVEL_INIT */ - - -#ifndef CONFIG_SPL_BUILD -/* - ************************************************************************* - * - * Interrupt handling - * - ************************************************************************* - */ - -@ -@ IRQ stack frame. -@ -#define S_FRAME_SIZE 72 - -#define S_OLD_R0 68 -#define S_PSR 64 -#define S_PC 60 -#define S_LR 56 -#define S_SP 52 - -#define S_IP 48 -#define S_FP 44 -#define S_R10 40 -#define S_R9 36 -#define S_R8 32 -#define S_R7 28 -#define S_R6 24 -#define S_R5 20 -#define S_R4 16 -#define S_R3 12 -#define S_R2 8 -#define S_R1 4 -#define S_R0 0 - -#define MODE_SVC 0x13 -#define I_BIT 0x80 - -/* - * use bad_save_user_regs for abort/prefetch/undef/swi ... - * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling - */ - - .macro bad_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - add r8, sp, #S_PC - - ldr r2, IRQ_STACK_START_IN - ldmia r2, {r2 - r4} @ get pc, cpsr, old_r0 - add r0, sp, #S_FRAME_SIZE @ restore sp_SVC - - add r5, sp, #S_SP - mov r1, lr - stmia r5, {r0 - r4} @ save sp_SVC, lr_SVC, pc, cpsr, old_r - mov r0, sp - .endm - - .macro irq_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - add r8, sp, #S_PC - stmdb r8, {sp, lr}^ @ Calling SP, LR - str lr, [r8, #0] @ Save calling PC - mrs r6, spsr - str r6, [r8, #4] @ Save CPSR - str r0, [r8, #8] @ Save OLD_R0 - mov r0, sp - .endm - - .macro irq_restore_user_regs - ldmia sp, {r0 - lr}^ @ Calling r0 - lr - mov r0, r0 - ldr lr, [sp, #S_PC] @ Get PC - add sp, sp, #S_FRAME_SIZE - subs pc, lr, #4 @ return & move spsr_svc into cpsr - .endm - - .macro get_bad_stack - ldr r13, IRQ_STACK_START_IN @ setup our mode stack - - str lr, [r13] @ save caller lr / spsr - mrs lr, spsr - str lr, [r13, #4] - - mov r13, #MODE_SVC @ prepare SVC-Mode - msr spsr_c, r13 - mov lr, pc - movs pc, lr - .endm - - .macro get_irq_stack @ setup IRQ stack - ldr sp, IRQ_STACK_START - .endm - - .macro get_fiq_stack @ setup FIQ stack - ldr sp, FIQ_STACK_START - .endm - -/* - * exception handlers - */ - .align 5 -undefined_instruction: - get_bad_stack - bad_save_user_regs - bl do_undefined_instruction - - .align 5 -software_interrupt: - get_bad_stack - bad_save_user_regs - bl do_software_interrupt - - .align 5 -prefetch_abort: - get_bad_stack - bad_save_user_regs - bl do_prefetch_abort - - .align 5 -data_abort: - get_bad_stack - bad_save_user_regs - bl do_data_abort - - .align 5 -not_used: - get_bad_stack - bad_save_user_regs - bl do_not_used - -#ifdef CONFIG_USE_IRQ - - .align 5 -irq: - get_irq_stack - irq_save_user_regs - bl do_irq - irq_restore_user_regs - - .align 5 -fiq: - get_fiq_stack - /* someone ought to write a more effiction fiq_save_user_regs */ - irq_save_user_regs - bl do_fiq - irq_restore_user_regs - -#else - - .align 5 -irq: - get_bad_stack - bad_save_user_regs - bl do_irq - - .align 5 -fiq: - get_bad_stack - bad_save_user_regs - bl do_fiq - -#endif -#endif /* CONFIG_SPL_BUILD */ diff --git a/arch/arm/cpu/arm720t/tegra-common/cpu.c b/arch/arm/cpu/arm720t/tegra-common/cpu.c index 168f525ec7..c6f3b029a1 100644 --- a/arch/arm/cpu/arm720t/tegra-common/cpu.c +++ b/arch/arm/cpu/arm720t/tegra-common/cpu.c @@ -82,7 +82,7 @@ struct clk_pll_table tegra_pll_x_table[TEGRA_SOC_CNT][CLOCK_OSC_FREQ_COUNT] = { { .n = 600, .m = 13, .p = 0, .cpcon = 12 }, /* OSC: 26.0 MHz */ }, /* - * T30: 1.4 GHz + * T30: 600 MHz * * Register Field Bits Width * ------------------------------ @@ -92,10 +92,10 @@ struct clk_pll_table tegra_pll_x_table[TEGRA_SOC_CNT][CLOCK_OSC_FREQ_COUNT] = { * PLLX_MISC cpcon 11: 8 4 */ { - { .n = 862, .m = 8, .p = 0, .cpcon = 8 }, /* OSC: 13.0 MHz */ - { .n = 583, .m = 8, .p = 0, .cpcon = 4 }, /* OSC: 19.2 MHz */ - { .n = 700, .m = 6, .p = 0, .cpcon = 8 }, /* OSC: 12.0 MHz */ - { .n = 700, .m = 13, .p = 0, .cpcon = 8 }, /* OSC: 26.0 MHz */ + { .n = 600, .m = 13, .p = 0, .cpcon = 8 }, /* OSC: 13.0 MHz */ + { .n = 500, .m = 16, .p = 0, .cpcon = 8 }, /* OSC: 19.2 MHz */ + { .n = 600, .m = 12, .p = 0, .cpcon = 8 }, /* OSC: 12.0 MHz */ + { .n = 600, .m = 26, .p = 0, .cpcon = 8 }, /* OSC: 26.0 MHz */ }, /* * T114: 700 MHz diff --git a/arch/arm/cpu/arm720t/tegra30/cpu.c b/arch/arm/cpu/arm720t/tegra30/cpu.c index a80648389c..9003902e3f 100644 --- a/arch/arm/cpu/arm720t/tegra30/cpu.c +++ b/arch/arm/cpu/arm720t/tegra30/cpu.c @@ -41,10 +41,18 @@ void tegra_i2c_ll_write_data(uint data, uint config) writel(config, ®->cnfg); } +#define TPS62366A_I2C_ADDR 0xC0 +#define TPS62366A_SET1_REG 0x01 +#define TPS62366A_SET1_DATA (0x4600 | TPS62366A_SET1_REG) + +#define TPS62361B_I2C_ADDR 0xC0 +#define TPS62361B_SET3_REG 0x03 +#define TPS62361B_SET3_DATA (0x4600 | TPS62361B_SET3_REG) + #define TPS65911_I2C_ADDR 0x5A #define TPS65911_VDDCTRL_OP_REG 0x28 #define TPS65911_VDDCTRL_SR_REG 0x27 -#define TPS65911_VDDCTRL_OP_DATA (0x2300 | TPS65911_VDDCTRL_OP_REG) +#define TPS65911_VDDCTRL_OP_DATA (0x2400 | TPS65911_VDDCTRL_OP_REG) #define TPS65911_VDDCTRL_SR_DATA (0x0100 | TPS65911_VDDCTRL_SR_REG) #define I2C_SEND_2_BYTES 0x0A02 @@ -58,9 +66,20 @@ static void enable_cpu_power_rail(void) reg |= CPUPWRREQ_OE; writel(reg, &pmc->pmc_cntrl); + /* Set VDD_CORE to 1.200V. */ +#ifdef CONFIG_TEGRA_VDD_CORE_TPS62366A_SET1 + tegra_i2c_ll_write_addr(TPS62366A_I2C_ADDR, 2); + tegra_i2c_ll_write_data(TPS62366A_SET1_DATA, I2C_SEND_2_BYTES); +#endif +#ifdef CONFIG_TEGRA_VDD_CORE_TPS62361B_SET3 + tegra_i2c_ll_write_addr(TPS62361B_I2C_ADDR, 2); + tegra_i2c_ll_write_data(TPS62361B_SET3_DATA, I2C_SEND_2_BYTES); +#endif + udelay(1000); + /* * Bring up CPU VDD via the TPS65911x PMIC on the DVC I2C bus. - * First set VDD to 1.4V, then enable the VDD regulator. + * First set VDD to 1.0125V, then enable the VDD regulator. */ tegra_i2c_ll_write_addr(TPS65911_I2C_ADDR, 2); tegra_i2c_ll_write_data(TPS65911_VDDCTRL_OP_DATA, I2C_SEND_2_BYTES); diff --git a/arch/arm/cpu/arm920t/ep93xx/u-boot.lds b/arch/arm/cpu/arm920t/ep93xx/u-boot.lds index 96994043e4..623a635208 100644 --- a/arch/arm/cpu/arm920t/ep93xx/u-boot.lds +++ b/arch/arm/cpu/arm920t/ep93xx/u-boot.lds @@ -16,7 +16,8 @@ SECTIONS .text : { *(.__image_copy_start) - arch/arm/cpu/arm920t/start.o (.text*) + *(.vectors) + arch/arm/cpu/arm920t/start.o (.text*) /* the EP93xx expects to find the pattern 'CRUS' at 0x1000 */ . = 0x1000; LONG(0x53555243) diff --git a/arch/arm/cpu/arm920t/start.S b/arch/arm/cpu/arm920t/start.S index 7bf094aec1..07404502c8 100644 --- a/arch/arm/cpu/arm920t/start.S +++ b/arch/arm/cpu/arm920t/start.S @@ -15,36 +15,6 @@ /* ************************************************************************* * - * Jump vector table as in table 3.1 in [1] - * - ************************************************************************* - */ - - -.globl _start -_start: b start_code - ldr pc, _undefined_instruction - ldr pc, _software_interrupt - ldr pc, _prefetch_abort - ldr pc, _data_abort - ldr pc, _not_used - ldr pc, _irq - ldr pc, _fiq - -_undefined_instruction: .word undefined_instruction -_software_interrupt: .word software_interrupt -_prefetch_abort: .word prefetch_abort -_data_abort: .word data_abort -_not_used: .word not_used -_irq: .word irq -_fiq: .word fiq - - .balignl 16,0xdeadbeef - - -/* - ************************************************************************* - * * Startup Code (called from the ARM reset exception vector) * * do important init only if we don't start from memory! @@ -55,28 +25,9 @@ _fiq: .word fiq ************************************************************************* */ -#ifdef CONFIG_USE_IRQ -/* IRQ stack memory (calculated at run-time) */ -.globl IRQ_STACK_START -IRQ_STACK_START: - .word 0x0badc0de - -/* IRQ stack memory (calculated at run-time) */ -.globl FIQ_STACK_START -FIQ_STACK_START: - .word 0x0badc0de -#endif - -/* IRQ stack memory (calculated at run-time) + 8 bytes */ -.globl IRQ_STACK_START_IN -IRQ_STACK_START_IN: - .word 0x0badc0de + .globl reset -/* - * the actual start code - */ - -start_code: +reset: /* * set the cpu to SVC32 mode */ @@ -196,166 +147,3 @@ cpu_init_crit: mov lr, ip mov pc, lr #endif /* CONFIG_SKIP_LOWLEVEL_INIT */ - -/* - ************************************************************************* - * - * Interrupt handling - * - ************************************************************************* - */ - -@ -@ IRQ stack frame. -@ -#define S_FRAME_SIZE 72 - -#define S_OLD_R0 68 -#define S_PSR 64 -#define S_PC 60 -#define S_LR 56 -#define S_SP 52 - -#define S_IP 48 -#define S_FP 44 -#define S_R10 40 -#define S_R9 36 -#define S_R8 32 -#define S_R7 28 -#define S_R6 24 -#define S_R5 20 -#define S_R4 16 -#define S_R3 12 -#define S_R2 8 -#define S_R1 4 -#define S_R0 0 - -#define MODE_SVC 0x13 -#define I_BIT 0x80 - -/* - * use bad_save_user_regs for abort/prefetch/undef/swi ... - * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling - */ - - .macro bad_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - ldr r2, IRQ_STACK_START_IN - ldmia r2, {r2 - r3} @ get pc, cpsr - add r0, sp, #S_FRAME_SIZE @ restore sp_SVC - - add r5, sp, #S_SP - mov r1, lr - stmia r5, {r0 - r3} @ save sp_SVC, lr_SVC, pc, cpsr - mov r0, sp - .endm - - .macro irq_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - add r7, sp, #S_PC - stmdb r7, {sp, lr}^ @ Calling SP, LR - str lr, [r7, #0] @ Save calling PC - mrs r6, spsr - str r6, [r7, #4] @ Save CPSR - str r0, [r7, #8] @ Save OLD_R0 - mov r0, sp - .endm - - .macro irq_restore_user_regs - ldmia sp, {r0 - lr}^ @ Calling r0 - lr - mov r0, r0 - ldr lr, [sp, #S_PC] @ Get PC - add sp, sp, #S_FRAME_SIZE - /* return & move spsr_svc into cpsr */ - subs pc, lr, #4 - .endm - - .macro get_bad_stack - ldr r13, IRQ_STACK_START_IN @ setup our mode stack - - str lr, [r13] @ save caller lr / spsr - mrs lr, spsr - str lr, [r13, #4] - - mov r13, #MODE_SVC @ prepare SVC-Mode - @ msr spsr_c, r13 - msr spsr, r13 - mov lr, pc - movs pc, lr - .endm - - .macro get_irq_stack @ setup IRQ stack - ldr sp, IRQ_STACK_START - .endm - - .macro get_fiq_stack @ setup FIQ stack - ldr sp, FIQ_STACK_START - .endm - -/* - * exception handlers - */ - .align 5 -undefined_instruction: - get_bad_stack - bad_save_user_regs - bl do_undefined_instruction - - .align 5 -software_interrupt: - get_bad_stack - bad_save_user_regs - bl do_software_interrupt - - .align 5 -prefetch_abort: - get_bad_stack - bad_save_user_regs - bl do_prefetch_abort - - .align 5 -data_abort: - get_bad_stack - bad_save_user_regs - bl do_data_abort - - .align 5 -not_used: - get_bad_stack - bad_save_user_regs - bl do_not_used - -#ifdef CONFIG_USE_IRQ - - .align 5 -irq: - get_irq_stack - irq_save_user_regs - bl do_irq - irq_restore_user_regs - - .align 5 -fiq: - get_fiq_stack - /* someone ought to write a more effiction fiq_save_user_regs */ - irq_save_user_regs - bl do_fiq - irq_restore_user_regs - -#else - - .align 5 -irq: - get_bad_stack - bad_save_user_regs - bl do_irq - - .align 5 -fiq: - get_bad_stack - bad_save_user_regs - bl do_fiq - -#endif diff --git a/arch/arm/cpu/arm926ejs/mxs/start.S b/arch/arm/cpu/arm926ejs/mxs/start.S index 34a0fcb462..9b60436539 100644 --- a/arch/arm/cpu/arm926ejs/mxs/start.S +++ b/arch/arm/cpu/arm926ejs/mxs/start.S @@ -27,70 +27,6 @@ /* ************************************************************************* * - * Jump vector table as in table 3.1 in [1] - * - ************************************************************************* - */ - - -.globl _start -_start: - b reset - b undefined_instruction - b software_interrupt - b prefetch_abort - b data_abort - b not_used - b irq - b fiq - -/* - * Vector table, located at address 0x20. - * This table allows the code running AFTER SPL, the U-Boot, to install it's - * interrupt handlers here. The problem is that the U-Boot is loaded into RAM, - * including it's interrupt vectoring table and the table at 0x0 is still the - * SPLs. So if interrupt happens in U-Boot, the SPLs interrupt vectoring table - * is still used. - */ -_vt_reset: - .word _reset -_vt_undefined_instruction: - .word _hang -_vt_software_interrupt: - .word _hang -_vt_prefetch_abort: - .word _hang -_vt_data_abort: - .word _hang -_vt_not_used: - .word _reset -_vt_irq: - .word _hang -_vt_fiq: - .word _hang - -reset: - ldr pc, _vt_reset -undefined_instruction: - ldr pc, _vt_undefined_instruction -software_interrupt: - ldr pc, _vt_software_interrupt -prefetch_abort: - ldr pc, _vt_prefetch_abort -data_abort: - ldr pc, _vt_data_abort -not_used: - ldr pc, _vt_not_used -irq: - ldr pc, _vt_irq -fiq: - ldr pc, _vt_fiq - - .balignl 16,0xdeadbeef - -/* - ************************************************************************* - * * Startup Code (reset vector) * * do important init only if we don't start from memory! @@ -101,28 +37,8 @@ fiq: ************************************************************************* */ -#ifdef CONFIG_USE_IRQ -/* IRQ stack memory (calculated at run-time) */ -.globl IRQ_STACK_START -IRQ_STACK_START: - .word 0x0badc0de - -/* IRQ stack memory (calculated at run-time) */ -.globl FIQ_STACK_START -FIQ_STACK_START: - .word 0x0badc0de -#endif - -/* IRQ stack memory (calculated at run-time) + 8 bytes */ -.globl IRQ_STACK_START_IN -IRQ_STACK_START_IN: - .word 0x0badc0de - -/* - * the actual reset code - */ - -_reset: + .globl reset +reset: /* * If the CPU is configured in "Wait JTAG connection mode", the stack * pointer is not configured and is zero. This will cause crash when @@ -179,7 +95,3 @@ _reset: mov r0, #0 bx lr - -_hang: -1: - bl 1b /* hang and never return */ diff --git a/arch/arm/cpu/arm926ejs/spear/start.S b/arch/arm/cpu/arm926ejs/spear/start.S index 7dbd5dbf99..290ac2e561 100644 --- a/arch/arm/cpu/arm926ejs/spear/start.S +++ b/arch/arm/cpu/arm926ejs/spear/start.S @@ -17,29 +17,6 @@ #include <config.h> -.globl _start -_start: - b reset - ldr pc, _undefined_instruction - ldr pc, _software_interrupt - ldr pc, _prefetch_abort - ldr pc, _data_abort - ldr pc, _not_used - ldr pc, _irq - ldr pc, _fiq - -_undefined_instruction: -_software_interrupt: -_prefetch_abort: -_data_abort: -_not_used: -_irq: -_fiq: - .word infinite_loop - -infinite_loop: - b infinite_loop - /* ************************************************************************* * @@ -53,9 +30,7 @@ infinite_loop: ************************************************************************* */ -/* - * the actual reset code - */ + .globl reset reset: /* diff --git a/arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds b/arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds index b6d0f65b66..c7ee19912f 100644 --- a/arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds +++ b/arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds @@ -21,6 +21,7 @@ SECTIONS . = ALIGN(4); .text : { + *(.vectors) arch/arm/cpu/arm926ejs/spear/start.o (.text*) *(.text*) } diff --git a/arch/arm/cpu/arm926ejs/start.S b/arch/arm/cpu/arm926ejs/start.S index 0717327050..8eb249475e 100644 --- a/arch/arm/cpu/arm926ejs/start.S +++ b/arch/arm/cpu/arm926ejs/start.S @@ -23,75 +23,6 @@ /* ************************************************************************* * - * Jump vector table as in table 3.1 in [1] - * - ************************************************************************* - */ - - -#ifdef CONFIG_SYS_DV_NOR_BOOT_CFG -.globl _start -_start: -.globl _NOR_BOOT_CFG -_NOR_BOOT_CFG: - .word CONFIG_SYS_DV_NOR_BOOT_CFG - b reset -#else -.globl _start -_start: - b reset -#endif -#ifdef CONFIG_SPL_BUILD -/* No exception handlers in preloader */ - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - -_hang: - .word do_hang -/* pad to 64 byte boundary */ - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 -#else - ldr pc, _undefined_instruction - ldr pc, _software_interrupt - ldr pc, _prefetch_abort - ldr pc, _data_abort - ldr pc, _not_used - ldr pc, _irq - ldr pc, _fiq - -_undefined_instruction: - .word undefined_instruction -_software_interrupt: - .word software_interrupt -_prefetch_abort: - .word prefetch_abort -_data_abort: - .word data_abort -_not_used: - .word not_used -_irq: - .word irq -_fiq: - .word fiq - -#endif /* CONFIG_SPL_BUILD */ - .balignl 16,0xdeadbeef - - -/* - ************************************************************************* - * * Startup Code (reset vector) * * do important init only if we don't start from memory! @@ -102,26 +33,7 @@ _fiq: ************************************************************************* */ -#ifdef CONFIG_USE_IRQ -/* IRQ stack memory (calculated at run-time) */ -.globl IRQ_STACK_START -IRQ_STACK_START: - .word 0x0badc0de - -/* IRQ stack memory (calculated at run-time) */ -.globl FIQ_STACK_START -FIQ_STACK_START: - .word 0x0badc0de -#endif - -/* IRQ stack memory (calculated at run-time) + 8 bytes */ -.globl IRQ_STACK_START_IN -IRQ_STACK_START_IN: - .word 0x0badc0de - -/* - * the actual reset code - */ + .globl reset reset: /* @@ -198,175 +110,3 @@ flush_dcache: mov lr, ip /* restore link */ mov pc, lr /* back to my caller */ #endif /* CONFIG_SKIP_LOWLEVEL_INIT */ - -#ifndef CONFIG_SPL_BUILD -/* - ************************************************************************* - * - * Interrupt handling - * - ************************************************************************* - */ - -@ -@ IRQ stack frame. -@ -#define S_FRAME_SIZE 72 - -#define S_OLD_R0 68 -#define S_PSR 64 -#define S_PC 60 -#define S_LR 56 -#define S_SP 52 - -#define S_IP 48 -#define S_FP 44 -#define S_R10 40 -#define S_R9 36 -#define S_R8 32 -#define S_R7 28 -#define S_R6 24 -#define S_R5 20 -#define S_R4 16 -#define S_R3 12 -#define S_R2 8 -#define S_R1 4 -#define S_R0 0 - -#define MODE_SVC 0x13 -#define I_BIT 0x80 - -/* - * use bad_save_user_regs for abort/prefetch/undef/swi ... - * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling - */ - - .macro bad_save_user_regs - @ carve out a frame on current user stack - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12 - ldr r2, IRQ_STACK_START_IN - @ get values for "aborted" pc and cpsr (into parm regs) - ldmia r2, {r2 - r3} - add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack - add r5, sp, #S_SP - mov r1, lr - stmia r5, {r0 - r3} @ save sp_SVC, lr_SVC, pc, cpsr - mov r0, sp @ save current stack into r0 (param register) - .endm - - .macro irq_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - @ !!!! R8 NEEDS to be saved !!!! a reserved stack spot would be good. - add r8, sp, #S_PC - stmdb r8, {sp, lr}^ @ Calling SP, LR - str lr, [r8, #0] @ Save calling PC - mrs r6, spsr - str r6, [r8, #4] @ Save CPSR - str r0, [r8, #8] @ Save OLD_R0 - mov r0, sp - .endm - - .macro irq_restore_user_regs - ldmia sp, {r0 - lr}^ @ Calling r0 - lr - mov r0, r0 - ldr lr, [sp, #S_PC] @ Get PC - add sp, sp, #S_FRAME_SIZE - subs pc, lr, #4 @ return & move spsr_svc into cpsr - .endm - - .macro get_bad_stack - ldr r13, IRQ_STACK_START_IN @ setup our mode stack - - str lr, [r13] @ save caller lr in position 0 of saved stack - mrs lr, spsr @ get the spsr - str lr, [r13, #4] @ save spsr in position 1 of saved stack - mov r13, #MODE_SVC @ prepare SVC-Mode - @ msr spsr_c, r13 - msr spsr, r13 @ switch modes, make sure moves will execute - mov lr, pc @ capture return pc - movs pc, lr @ jump to next instruction & switch modes. - .endm - - .macro get_irq_stack @ setup IRQ stack - ldr sp, IRQ_STACK_START - .endm - - .macro get_fiq_stack @ setup FIQ stack - ldr sp, FIQ_STACK_START - .endm -#endif /* CONFIG_SPL_BUILD */ - -/* - * exception handlers - */ -#ifdef CONFIG_SPL_BUILD - .align 5 -do_hang: -1: - bl 1b /* hang and never return */ -#else /* !CONFIG_SPL_BUILD */ - .align 5 -undefined_instruction: - get_bad_stack - bad_save_user_regs - bl do_undefined_instruction - - .align 5 -software_interrupt: - get_bad_stack - bad_save_user_regs - bl do_software_interrupt - - .align 5 -prefetch_abort: - get_bad_stack - bad_save_user_regs - bl do_prefetch_abort - - .align 5 -data_abort: - get_bad_stack - bad_save_user_regs - bl do_data_abort - - .align 5 -not_used: - get_bad_stack - bad_save_user_regs - bl do_not_used - -#ifdef CONFIG_USE_IRQ - - .align 5 -irq: - get_irq_stack - irq_save_user_regs - bl do_irq - irq_restore_user_regs - - .align 5 -fiq: - get_fiq_stack - /* someone ought to write a more effiction fiq_save_user_regs */ - irq_save_user_regs - bl do_fiq - irq_restore_user_regs - -#else - - .align 5 -irq: - get_bad_stack - bad_save_user_regs - bl do_irq - - .align 5 -fiq: - get_bad_stack - bad_save_user_regs - bl do_fiq - -#endif -#endif /* CONFIG_SPL_BUILD */ diff --git a/arch/arm/cpu/arm946es/cpu.c b/arch/arm/cpu/arm946es/cpu.c index 0c8d92d737..e20e5a89aa 100644 --- a/arch/arm/cpu/arm946es/cpu.c +++ b/arch/arm/cpu/arm946es/cpu.c @@ -16,6 +16,7 @@ #include <common.h> #include <command.h> #include <asm/system.h> +#include <asm/io.h> static void cache_flush(void); @@ -51,3 +52,15 @@ static void cache_flush (void) asm ("mcr p15, 0, %0, c7, c5, 0": :"r" (i)); asm ("mcr p15, 0, %0, c7, c6, 0": :"r" (i)); } + +#ifndef CONFIG_INTEGRATOR + +__attribute__((noreturn)) void reset_cpu(ulong addr __attribute__((unused))) +{ + writew(0x0, 0xfffece10); + writew(0x8, 0xfffece10); + for (;;) + ; +} + +#endif /* #ifdef CONFIG_INTEGRATOR */ diff --git a/arch/arm/cpu/arm946es/start.S b/arch/arm/cpu/arm946es/start.S index 7d50145836..41123716a7 100644 --- a/arch/arm/cpu/arm946es/start.S +++ b/arch/arm/cpu/arm946es/start.S @@ -22,45 +22,6 @@ /* ************************************************************************* * - * Jump vector table as in table 3.1 in [1] - * - ************************************************************************* - */ - - -.globl _start -_start: - b reset - ldr pc, _undefined_instruction - ldr pc, _software_interrupt - ldr pc, _prefetch_abort - ldr pc, _data_abort - ldr pc, _not_used - ldr pc, _irq - ldr pc, _fiq - -_undefined_instruction: - .word undefined_instruction -_software_interrupt: - .word software_interrupt -_prefetch_abort: - .word prefetch_abort -_data_abort: - .word data_abort -_not_used: - .word not_used -_irq: - .word irq -_fiq: - .word fiq - - .balignl 16,0xdeadbeef - -_vectors_end: - -/* - ************************************************************************* - * * Startup Code (reset vector) * * do important init only if we don't start from memory! @@ -71,26 +32,7 @@ _vectors_end: ************************************************************************* */ -#ifdef CONFIG_USE_IRQ -/* IRQ stack memory (calculated at run-time) */ -.globl IRQ_STACK_START -IRQ_STACK_START: - .word 0x0badc0de - -/* IRQ stack memory (calculated at run-time) */ -.globl FIQ_STACK_START -FIQ_STACK_START: - .word 0x0badc0de -#endif - -/* IRQ stack memory (calculated at run-time) + 8 bytes */ -.globl IRQ_STACK_START_IN -IRQ_STACK_START_IN: - .word 0x0badc0de - -/* - * the actual reset code - */ + .globl reset reset: /* @@ -157,189 +99,3 @@ cpu_init_crit: mov lr, ip /* restore link */ mov pc, lr /* back to my caller */ #endif -/* - ************************************************************************* - * - * Interrupt handling - * - ************************************************************************* - */ - -@ -@ IRQ stack frame. -@ -#define S_FRAME_SIZE 72 - -#define S_OLD_R0 68 -#define S_PSR 64 -#define S_PC 60 -#define S_LR 56 -#define S_SP 52 - -#define S_IP 48 -#define S_FP 44 -#define S_R10 40 -#define S_R9 36 -#define S_R8 32 -#define S_R7 28 -#define S_R6 24 -#define S_R5 20 -#define S_R4 16 -#define S_R3 12 -#define S_R2 8 -#define S_R1 4 -#define S_R0 0 - -#define MODE_SVC 0x13 -#define I_BIT 0x80 - -/* - * use bad_save_user_regs for abort/prefetch/undef/swi ... - * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling - */ - - .macro bad_save_user_regs - @ carve out a frame on current user stack - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12 - - ldr r2, IRQ_STACK_START_IN - @ get values for "aborted" pc and cpsr (into parm regs) - ldmia r2, {r2 - r3} - add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack - add r5, sp, #S_SP - mov r1, lr - stmia r5, {r0 - r3} @ save sp_SVC, lr_SVC, pc, cpsr - mov r0, sp @ save current stack into r0 (param register) - .endm - - .macro irq_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - @ !!!! R8 NEEDS to be saved !!!! a reserved stack spot would be good. - add r8, sp, #S_PC - stmdb r8, {sp, lr}^ @ Calling SP, LR - str lr, [r8, #0] @ Save calling PC - mrs r6, spsr - str r6, [r8, #4] @ Save CPSR - str r0, [r8, #8] @ Save OLD_R0 - mov r0, sp - .endm - - .macro irq_restore_user_regs - ldmia sp, {r0 - lr}^ @ Calling r0 - lr - mov r0, r0 - ldr lr, [sp, #S_PC] @ Get PC - add sp, sp, #S_FRAME_SIZE - subs pc, lr, #4 @ return & move spsr_svc into cpsr - .endm - - .macro get_bad_stack - ldr r13, IRQ_STACK_START_IN @ setup our mode stack - - str lr, [r13] @ save caller lr in position 0 of saved stack - mrs lr, spsr @ get the spsr - str lr, [r13, #4] @ save spsr in position 1 of saved stack - mov r13, #MODE_SVC @ prepare SVC-Mode - @ msr spsr_c, r13 - msr spsr, r13 @ switch modes, make sure moves will execute - mov lr, pc @ capture return pc - movs pc, lr @ jump to next instruction & switch modes. - .endm - - .macro get_irq_stack @ setup IRQ stack - ldr sp, IRQ_STACK_START - .endm - - .macro get_fiq_stack @ setup FIQ stack - ldr sp, FIQ_STACK_START - .endm - -/* - * exception handlers - */ - .align 5 -undefined_instruction: - get_bad_stack - bad_save_user_regs - bl do_undefined_instruction - - .align 5 -software_interrupt: - get_bad_stack - bad_save_user_regs - bl do_software_interrupt - - .align 5 -prefetch_abort: - get_bad_stack - bad_save_user_regs - bl do_prefetch_abort - - .align 5 -data_abort: - get_bad_stack - bad_save_user_regs - bl do_data_abort - - .align 5 -not_used: - get_bad_stack - bad_save_user_regs - bl do_not_used - -#ifdef CONFIG_USE_IRQ - - .align 5 -irq: - get_irq_stack - irq_save_user_regs - bl do_irq - irq_restore_user_regs - - .align 5 -fiq: - get_fiq_stack - /* someone ought to write a more effiction fiq_save_user_regs */ - irq_save_user_regs - bl do_fiq - irq_restore_user_regs - -#else - - .align 5 -irq: - get_bad_stack - bad_save_user_regs - bl do_irq - - .align 5 -fiq: - get_bad_stack - bad_save_user_regs - bl do_fiq - -#endif - -# ifdef CONFIG_INTEGRATOR - - /* Satisfied by general board level routine */ - -#else - - .align 5 -.globl reset_cpu -reset_cpu: - - ldr r1, rstctl1 /* get clkm1 reset ctl */ - mov r3, #0x0 - strh r3, [r1] /* clear it */ - mov r3, #0x8 - strh r3, [r1] /* force dsp+arm reset */ -_loop_forever: - b _loop_forever - -rstctl1: - .word 0xfffece10 - -#endif /* #ifdef CONFIG_INTEGRATOR */ diff --git a/arch/arm/cpu/arm_intcm/start.S b/arch/arm/cpu/arm_intcm/start.S index 7404ea7348..c0c07b6a11 100644 --- a/arch/arm/cpu/arm_intcm/start.S +++ b/arch/arm/cpu/arm_intcm/start.S @@ -21,42 +21,6 @@ /* ************************************************************************* * - * Jump vector table - * - ************************************************************************* - */ - -.globl _start -_start: - b reset - ldr pc, _undefined_instruction - ldr pc, _software_interrupt - ldr pc, _prefetch_abort - ldr pc, _data_abort - ldr pc, _not_used - ldr pc, _irq - ldr pc, _fiq - -_undefined_instruction: - .word undefined_instruction -_software_interrupt: - .word software_interrupt -_prefetch_abort: - .word prefetch_abort -_data_abort: - .word data_abort -_not_used: - .word not_used -_irq: - .word irq -_fiq: - .word fiq - - .balignl 16,0xdeadbeef - -/* - ************************************************************************* - * * Startup Code (reset vector) * * do important init only if we don't start from memory! @@ -67,26 +31,7 @@ _fiq: ************************************************************************* */ -#ifdef CONFIG_USE_IRQ -/* IRQ stack memory (calculated at run-time) */ -.globl IRQ_STACK_START -IRQ_STACK_START: - .word 0x0badc0de - -/* IRQ stack memory (calculated at run-time) */ -.globl FIQ_STACK_START -FIQ_STACK_START: - .word 0x0badc0de -#endif - -/* IRQ stack memory (calculated at run-time) + 8 bytes */ -.globl IRQ_STACK_START_IN -IRQ_STACK_START_IN: - .word 0x0badc0de - -/* - * the actual reset code - */ + .globl reset reset: /* @@ -132,174 +77,3 @@ cpu_init_crit: */ mov pc, lr /* back to my caller */ #endif -/* - ************************************************************************* - * - * Interrupt handling - * - ************************************************************************* - */ - -@ -@ IRQ stack frame. -@ -#define S_FRAME_SIZE 72 - -#define S_OLD_R0 68 -#define S_PSR 64 -#define S_PC 60 -#define S_LR 56 -#define S_SP 52 - -#define S_IP 48 -#define S_FP 44 -#define S_R10 40 -#define S_R9 36 -#define S_R8 32 -#define S_R7 28 -#define S_R6 24 -#define S_R5 20 -#define S_R4 16 -#define S_R3 12 -#define S_R2 8 -#define S_R1 4 -#define S_R0 0 - -#define MODE_SVC 0x13 -#define I_BIT 0x80 - -/* - * use bad_save_user_regs for abort/prefetch/undef/swi ... - * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling - */ - - .macro bad_save_user_regs - @ carve out a frame on current user stack - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12 - - ldr r2, IRQ_STACK_START_IN - @ get values for "aborted" pc and cpsr (into parm regs) - ldmia r2, {r2 - r3} - add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack - add r5, sp, #S_SP - mov r1, lr - stmia r5, {r0 - r3} @ save sp_SVC, lr_SVC, pc, cpsr - mov r0, sp @ save current stack into r0 (param register) - .endm - - .macro irq_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - @ !!!! R8 NEEDS to be saved !!!! a reserved stack spot would be good. - add r8, sp, #S_PC - stmdb r8, {sp, lr}^ @ Calling SP, LR - str lr, [r8, #0] @ Save calling PC - mrs r6, spsr - str r6, [r8, #4] @ Save CPSR - str r0, [r8, #8] @ Save OLD_R0 - mov r0, sp - .endm - - .macro irq_restore_user_regs - ldmia sp, {r0 - lr}^ @ Calling r0 - lr - mov r0, r0 - ldr lr, [sp, #S_PC] @ Get PC - add sp, sp, #S_FRAME_SIZE - subs pc, lr, #4 @ return & move spsr_svc into cpsr - .endm - - .macro get_bad_stack - ldr r13, IRQ_STACK_START_IN @ setup our mode stack - - str lr, [r13] @ save caller lr in position 0 of saved stack - mrs lr, spsr @ get the spsr - str lr, [r13, #4] @ save spsr in position 1 of saved stack - mov r13, #MODE_SVC @ prepare SVC-Mode - @ msr spsr_c, r13 - msr spsr, r13 @ switch modes, make sure moves will execute - mov lr, pc @ capture return pc - movs pc, lr @ jump to next instruction & switch modes. - .endm - - .macro get_irq_stack @ setup IRQ stack - ldr sp, IRQ_STACK_START - .endm - - .macro get_fiq_stack @ setup FIQ stack - ldr sp, FIQ_STACK_START - .endm - -/* - * exception handlers - */ - .align 5 -.globl undefined_instruction -undefined_instruction: - get_bad_stack - bad_save_user_regs - bl do_undefined_instruction - - .align 5 -.globl software_interrupt -software_interrupt: - get_bad_stack - bad_save_user_regs - bl do_software_interrupt - - .align 5 -.globl prefetch_abort -prefetch_abort: - get_bad_stack - bad_save_user_regs - bl do_prefetch_abort - - .align 5 -.globl data_abort -data_abort: - get_bad_stack - bad_save_user_regs - bl do_data_abort - - .align 5 -.globl not_used -not_used: - get_bad_stack - bad_save_user_regs - bl do_not_used - -#ifdef CONFIG_USE_IRQ - .align 5 -.globl irq -irq: - get_irq_stack - irq_save_user_regs - bl do_irq - irq_restore_user_regs - - .align 5 -.globl fiq -fiq: - get_fiq_stack - /* someone ought to write a more effiction fiq_save_user_regs */ - irq_save_user_regs - bl do_fiq - irq_restore_user_regs - -#else - - .align 5 -.globl irq -irq: - get_bad_stack - bad_save_user_regs - bl do_irq - - .align 5 -.globl fiq -fiq: - get_bad_stack - bad_save_user_regs - bl do_fiq - -#endif diff --git a/arch/arm/cpu/armv7/exynos/pinmux.c b/arch/arm/cpu/armv7/exynos/pinmux.c index 9edb47502c..ee7c2e5a4b 100644 --- a/arch/arm/cpu/armv7/exynos/pinmux.c +++ b/arch/arm/cpu/armv7/exynos/pinmux.c @@ -13,30 +13,23 @@ static void exynos5_uart_config(int peripheral) { - struct exynos5_gpio_part1 *gpio1 = - (struct exynos5_gpio_part1 *) samsung_get_base_gpio_part1(); - struct s5p_gpio_bank *bank; int i, start, count; switch (peripheral) { case PERIPH_ID_UART0: - bank = &gpio1->a0; - start = 0; + start = EXYNOS5_GPIO_A00; count = 4; break; case PERIPH_ID_UART1: - bank = &gpio1->d0; - start = 0; + start = EXYNOS5_GPIO_D00; count = 4; break; case PERIPH_ID_UART2: - bank = &gpio1->a1; - start = 0; + start = EXYNOS5_GPIO_A10; count = 4; break; case PERIPH_ID_UART3: - bank = &gpio1->a1; - start = 4; + start = EXYNOS5_GPIO_A14; count = 2; break; default: @@ -44,37 +37,30 @@ static void exynos5_uart_config(int peripheral) return; } for (i = start; i < start + count; i++) { - s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE); - s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2)); + gpio_set_pull(i, S5P_GPIO_PULL_NONE); + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x2)); } } static void exynos5420_uart_config(int peripheral) { - struct exynos5420_gpio_part1 *gpio1 = - (struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1(); - struct s5p_gpio_bank *bank; int i, start, count; switch (peripheral) { case PERIPH_ID_UART0: - bank = &gpio1->a0; - start = 0; + start = EXYNOS5420_GPIO_A00; count = 4; break; case PERIPH_ID_UART1: - bank = &gpio1->a0; - start = 4; + start = EXYNOS5420_GPIO_A04; count = 4; break; case PERIPH_ID_UART2: - bank = &gpio1->a1; - start = 0; + start = EXYNOS5420_GPIO_A10; count = 4; break; case PERIPH_ID_UART3: - bank = &gpio1->a1; - start = 4; + start = EXYNOS5420_GPIO_A14; count = 2; break; default: @@ -83,64 +69,59 @@ static void exynos5420_uart_config(int peripheral) } for (i = start; i < start + count; i++) { - s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE); - s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2)); + gpio_set_pull(i, S5P_GPIO_PULL_NONE); + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x2)); } } static int exynos5_mmc_config(int peripheral, int flags) { - struct exynos5_gpio_part1 *gpio1 = - (struct exynos5_gpio_part1 *) samsung_get_base_gpio_part1(); - struct s5p_gpio_bank *bank, *bank_ext; - int i, start = 0, gpio_func = 0; + int i, start, start_ext, gpio_func = 0; switch (peripheral) { case PERIPH_ID_SDMMC0: - bank = &gpio1->c0; - bank_ext = &gpio1->c1; - start = 0; - gpio_func = GPIO_FUNC(0x2); + start = EXYNOS5_GPIO_C00; + start_ext = EXYNOS5_GPIO_C10; + gpio_func = S5P_GPIO_FUNC(0x2); break; case PERIPH_ID_SDMMC1: - bank = &gpio1->c2; - bank_ext = NULL; + start = EXYNOS5_GPIO_C20; + start_ext = 0; break; case PERIPH_ID_SDMMC2: - bank = &gpio1->c3; - bank_ext = &gpio1->c4; - start = 3; - gpio_func = GPIO_FUNC(0x3); + start = EXYNOS5_GPIO_C30; + start_ext = EXYNOS5_GPIO_C43; + gpio_func = S5P_GPIO_FUNC(0x3); break; case PERIPH_ID_SDMMC3: - bank = &gpio1->c4; - bank_ext = NULL; + start = EXYNOS5_GPIO_C40; + start_ext = 0; break; default: debug("%s: invalid peripheral %d", __func__, peripheral); return -1; } - if ((flags & PINMUX_FLAG_8BIT_MODE) && !bank_ext) { + if ((flags & PINMUX_FLAG_8BIT_MODE) && !start_ext) { debug("SDMMC device %d does not support 8bit mode", peripheral); return -1; } if (flags & PINMUX_FLAG_8BIT_MODE) { - for (i = start; i <= (start + 3); i++) { - s5p_gpio_cfg_pin(bank_ext, i, gpio_func); - s5p_gpio_set_pull(bank_ext, i, GPIO_PULL_UP); - s5p_gpio_set_drv(bank_ext, i, GPIO_DRV_4X); + for (i = start_ext; i <= (start_ext + 3); i++) { + gpio_cfg_pin(i, gpio_func); + gpio_set_pull(i, S5P_GPIO_PULL_UP); + gpio_set_drv(i, S5P_GPIO_DRV_4X); } } - for (i = 0; i < 2; i++) { - s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2)); - s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE); - s5p_gpio_set_drv(bank, i, GPIO_DRV_4X); + for (i = start; i < (start + 2); i++) { + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x2)); + gpio_set_pull(i, S5P_GPIO_PULL_NONE); + gpio_set_drv(i, S5P_GPIO_DRV_4X); } - for (i = 3; i <= 6; i++) { - s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2)); - s5p_gpio_set_pull(bank, i, GPIO_PULL_UP); - s5p_gpio_set_drv(bank, i, GPIO_DRV_4X); + for (i = (start + 3); i <= (start + 6); i++) { + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x2)); + gpio_set_pull(i, S5P_GPIO_PULL_UP); + gpio_set_drv(i, S5P_GPIO_DRV_4X); } return 0; @@ -148,26 +129,20 @@ static int exynos5_mmc_config(int peripheral, int flags) static int exynos5420_mmc_config(int peripheral, int flags) { - struct exynos5420_gpio_part3 *gpio3 = - (struct exynos5420_gpio_part3 *)samsung_get_base_gpio_part3(); - struct s5p_gpio_bank *bank = NULL, *bank_ext = NULL; - int i, start; + int i, start = 0, start_ext = 0; switch (peripheral) { case PERIPH_ID_SDMMC0: - bank = &gpio3->c0; - bank_ext = &gpio3->c3; - start = 0; + start = EXYNOS5420_GPIO_C00; + start_ext = EXYNOS5420_GPIO_C30; break; case PERIPH_ID_SDMMC1: - bank = &gpio3->c1; - bank_ext = &gpio3->d1; - start = 4; + start = EXYNOS5420_GPIO_C10; + start_ext = EXYNOS5420_GPIO_D14; break; case PERIPH_ID_SDMMC2: - bank = &gpio3->c2; - bank_ext = NULL; - start = 0; + start = EXYNOS5420_GPIO_C20; + start_ext = 0; break; default: start = 0; @@ -175,41 +150,41 @@ static int exynos5420_mmc_config(int peripheral, int flags) return -1; } - if ((flags & PINMUX_FLAG_8BIT_MODE) && !bank_ext) { + if ((flags & PINMUX_FLAG_8BIT_MODE) && !start_ext) { debug("SDMMC device %d does not support 8bit mode", peripheral); return -1; } if (flags & PINMUX_FLAG_8BIT_MODE) { - for (i = start; i <= (start + 3); i++) { - s5p_gpio_cfg_pin(bank_ext, i, GPIO_FUNC(0x2)); - s5p_gpio_set_pull(bank_ext, i, GPIO_PULL_UP); - s5p_gpio_set_drv(bank_ext, i, GPIO_DRV_4X); + for (i = start_ext; i <= (start_ext + 3); i++) { + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x2)); + gpio_set_pull(i, S5P_GPIO_PULL_UP); + gpio_set_drv(i, S5P_GPIO_DRV_4X); } } - for (i = 0; i < 3; i++) { + for (i = start; i < (start + 3); i++) { /* * MMC0 is intended to be used for eMMC. The * card detect pin is used as a VDDEN signal to * power on the eMMC. The 5420 iROM makes * this same assumption. */ - if ((peripheral == PERIPH_ID_SDMMC0) && (i == 2)) { - s5p_gpio_set_value(bank, i, 1); - s5p_gpio_cfg_pin(bank, i, GPIO_OUTPUT); + if ((peripheral == PERIPH_ID_SDMMC0) && (i == (start + 2))) { + gpio_set_value(i, 1); + gpio_cfg_pin(i, S5P_GPIO_OUTPUT); } else { - s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2)); + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x2)); } - s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE); - s5p_gpio_set_drv(bank, i, GPIO_DRV_4X); + gpio_set_pull(i, S5P_GPIO_PULL_NONE); + gpio_set_drv(i, S5P_GPIO_DRV_4X); } - for (i = 3; i <= 6; i++) { - s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2)); - s5p_gpio_set_pull(bank, i, GPIO_PULL_UP); - s5p_gpio_set_drv(bank, i, GPIO_DRV_4X); + for (i = (start + 3); i <= (start + 6); i++) { + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x2)); + gpio_set_pull(i, S5P_GPIO_PULL_UP); + gpio_set_drv(i, S5P_GPIO_DRV_4X); } return 0; @@ -217,8 +192,6 @@ static int exynos5420_mmc_config(int peripheral, int flags) static void exynos5_sromc_config(int flags) { - struct exynos5_gpio_part1 *gpio1 = - (struct exynos5_gpio_part1 *) samsung_get_base_gpio_part1(); int i; /* @@ -236,13 +209,13 @@ static void exynos5_sromc_config(int flags) * GPY1[2] SROM_WAIT(2) * GPY1[3] EBI_DATA_RDn(2) */ - s5p_gpio_cfg_pin(&gpio1->y0, (flags & PINMUX_FLAG_BANK), - GPIO_FUNC(2)); - s5p_gpio_cfg_pin(&gpio1->y0, 4, GPIO_FUNC(2)); - s5p_gpio_cfg_pin(&gpio1->y0, 5, GPIO_FUNC(2)); + gpio_cfg_pin(EXYNOS5_GPIO_Y00 + (flags & PINMUX_FLAG_BANK), + S5P_GPIO_FUNC(2)); + gpio_cfg_pin(EXYNOS5_GPIO_Y04, S5P_GPIO_FUNC(2)); + gpio_cfg_pin(EXYNOS5_GPIO_Y05, S5P_GPIO_FUNC(2)); for (i = 0; i < 4; i++) - s5p_gpio_cfg_pin(&gpio1->y1, i, GPIO_FUNC(2)); + gpio_cfg_pin(EXYNOS5_GPIO_Y10 + i, S5P_GPIO_FUNC(2)); /* * EBI: 8 Addrss Lines @@ -277,108 +250,101 @@ static void exynos5_sromc_config(int flags) * GPY6[7] EBI_DATA[15](2) */ for (i = 0; i < 8; i++) { - s5p_gpio_cfg_pin(&gpio1->y3, i, GPIO_FUNC(2)); - s5p_gpio_set_pull(&gpio1->y3, i, GPIO_PULL_UP); + gpio_cfg_pin(EXYNOS5_GPIO_Y30 + i, S5P_GPIO_FUNC(2)); + gpio_set_pull(EXYNOS5_GPIO_Y30 + i, S5P_GPIO_PULL_UP); - s5p_gpio_cfg_pin(&gpio1->y5, i, GPIO_FUNC(2)); - s5p_gpio_set_pull(&gpio1->y5, i, GPIO_PULL_UP); + gpio_cfg_pin(EXYNOS5_GPIO_Y50 + i, S5P_GPIO_FUNC(2)); + gpio_set_pull(EXYNOS5_GPIO_Y50 + i, S5P_GPIO_PULL_UP); - s5p_gpio_cfg_pin(&gpio1->y6, i, GPIO_FUNC(2)); - s5p_gpio_set_pull(&gpio1->y6, i, GPIO_PULL_UP); + gpio_cfg_pin(EXYNOS5_GPIO_Y60 + i, S5P_GPIO_FUNC(2)); + gpio_set_pull(EXYNOS5_GPIO_Y60 + i, S5P_GPIO_PULL_UP); } } static void exynos5_i2c_config(int peripheral, int flags) { - - struct exynos5_gpio_part1 *gpio1 = - (struct exynos5_gpio_part1 *) samsung_get_base_gpio_part1(); - switch (peripheral) { case PERIPH_ID_I2C0: - s5p_gpio_cfg_pin(&gpio1->b3, 0, GPIO_FUNC(0x2)); - s5p_gpio_cfg_pin(&gpio1->b3, 1, GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5_GPIO_B30, S5P_GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5_GPIO_B31, S5P_GPIO_FUNC(0x2)); break; case PERIPH_ID_I2C1: - s5p_gpio_cfg_pin(&gpio1->b3, 2, GPIO_FUNC(0x2)); - s5p_gpio_cfg_pin(&gpio1->b3, 3, GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5_GPIO_B32, S5P_GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5_GPIO_B33, S5P_GPIO_FUNC(0x2)); break; case PERIPH_ID_I2C2: - s5p_gpio_cfg_pin(&gpio1->a0, 6, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->a0, 7, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5_GPIO_A06, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5_GPIO_A07, S5P_GPIO_FUNC(0x3)); break; case PERIPH_ID_I2C3: - s5p_gpio_cfg_pin(&gpio1->a1, 2, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->a1, 3, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5_GPIO_A12, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5_GPIO_A13, S5P_GPIO_FUNC(0x3)); break; case PERIPH_ID_I2C4: - s5p_gpio_cfg_pin(&gpio1->a2, 0, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->a2, 1, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5_GPIO_A20, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5_GPIO_A21, S5P_GPIO_FUNC(0x3)); break; case PERIPH_ID_I2C5: - s5p_gpio_cfg_pin(&gpio1->a2, 2, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->a2, 3, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5_GPIO_A22, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5_GPIO_A23, S5P_GPIO_FUNC(0x3)); break; case PERIPH_ID_I2C6: - s5p_gpio_cfg_pin(&gpio1->b1, 3, GPIO_FUNC(0x4)); - s5p_gpio_cfg_pin(&gpio1->b1, 4, GPIO_FUNC(0x4)); + gpio_cfg_pin(EXYNOS5_GPIO_B13, S5P_GPIO_FUNC(0x4)); + gpio_cfg_pin(EXYNOS5_GPIO_B14, S5P_GPIO_FUNC(0x4)); break; case PERIPH_ID_I2C7: - s5p_gpio_cfg_pin(&gpio1->b2, 2, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->b2, 3, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5_GPIO_B22, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5_GPIO_B23, S5P_GPIO_FUNC(0x3)); break; } } static void exynos5420_i2c_config(int peripheral) { - struct exynos5420_gpio_part1 *gpio1 = - (struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1(); - switch (peripheral) { case PERIPH_ID_I2C0: - s5p_gpio_cfg_pin(&gpio1->b3, 0, GPIO_FUNC(0x2)); - s5p_gpio_cfg_pin(&gpio1->b3, 1, GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5420_GPIO_B30, S5P_GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5420_GPIO_B31, S5P_GPIO_FUNC(0x2)); break; case PERIPH_ID_I2C1: - s5p_gpio_cfg_pin(&gpio1->b3, 2, GPIO_FUNC(0x2)); - s5p_gpio_cfg_pin(&gpio1->b3, 3, GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5420_GPIO_B32, S5P_GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5420_GPIO_B33, S5P_GPIO_FUNC(0x2)); break; case PERIPH_ID_I2C2: - s5p_gpio_cfg_pin(&gpio1->a0, 6, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->a0, 7, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5420_GPIO_A06, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5420_GPIO_A07, S5P_GPIO_FUNC(0x3)); break; case PERIPH_ID_I2C3: - s5p_gpio_cfg_pin(&gpio1->a1, 2, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->a1, 3, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5420_GPIO_A12, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5420_GPIO_A13, S5P_GPIO_FUNC(0x3)); break; case PERIPH_ID_I2C4: - s5p_gpio_cfg_pin(&gpio1->a2, 0, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->a2, 1, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5420_GPIO_A20, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5420_GPIO_A21, S5P_GPIO_FUNC(0x3)); break; case PERIPH_ID_I2C5: - s5p_gpio_cfg_pin(&gpio1->a2, 2, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->a2, 3, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5420_GPIO_A22, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5420_GPIO_A23, S5P_GPIO_FUNC(0x3)); break; case PERIPH_ID_I2C6: - s5p_gpio_cfg_pin(&gpio1->b1, 3, GPIO_FUNC(0x4)); - s5p_gpio_cfg_pin(&gpio1->b1, 4, GPIO_FUNC(0x4)); + gpio_cfg_pin(EXYNOS5420_GPIO_B13, S5P_GPIO_FUNC(0x4)); + gpio_cfg_pin(EXYNOS5420_GPIO_B14, S5P_GPIO_FUNC(0x4)); break; case PERIPH_ID_I2C7: - s5p_gpio_cfg_pin(&gpio1->b2, 2, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->b2, 3, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5420_GPIO_B22, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5420_GPIO_B23, S5P_GPIO_FUNC(0x3)); break; case PERIPH_ID_I2C8: - s5p_gpio_cfg_pin(&gpio1->b3, 4, GPIO_FUNC(0x2)); - s5p_gpio_cfg_pin(&gpio1->b3, 5, GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5420_GPIO_B34, S5P_GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5420_GPIO_B35, S5P_GPIO_FUNC(0x2)); break; case PERIPH_ID_I2C9: - s5p_gpio_cfg_pin(&gpio1->b3, 6, GPIO_FUNC(0x2)); - s5p_gpio_cfg_pin(&gpio1->b3, 7, GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5420_GPIO_B36, S5P_GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5420_GPIO_B37, S5P_GPIO_FUNC(0x2)); break; case PERIPH_ID_I2C10: - s5p_gpio_cfg_pin(&gpio1->b4, 0, GPIO_FUNC(0x2)); - s5p_gpio_cfg_pin(&gpio1->b4, 1, GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5420_GPIO_B40, S5P_GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS5420_GPIO_B41, S5P_GPIO_FUNC(0x2)); break; } } @@ -386,19 +352,15 @@ static void exynos5420_i2c_config(int peripheral) static void exynos5_i2s_config(int peripheral) { int i; - struct exynos5_gpio_part1 *gpio1 = - (struct exynos5_gpio_part1 *)samsung_get_base_gpio_part1(); - struct exynos5_gpio_part4 *gpio4 = - (struct exynos5_gpio_part4 *)samsung_get_base_gpio_part4(); switch (peripheral) { case PERIPH_ID_I2S0: for (i = 0; i < 5; i++) - s5p_gpio_cfg_pin(&gpio4->z, i, GPIO_FUNC(0x02)); + gpio_cfg_pin(EXYNOS5_GPIO_Z0 + i, S5P_GPIO_FUNC(0x02)); break; case PERIPH_ID_I2S1: for (i = 0; i < 5; i++) - s5p_gpio_cfg_pin(&gpio1->b0, i, GPIO_FUNC(0x02)); + gpio_cfg_pin(EXYNOS5_GPIO_B00 + i, S5P_GPIO_FUNC(0x02)); break; } } @@ -406,75 +368,57 @@ static void exynos5_i2s_config(int peripheral) void exynos5_spi_config(int peripheral) { int cfg = 0, pin = 0, i; - struct s5p_gpio_bank *bank = NULL; - struct exynos5_gpio_part1 *gpio1 = - (struct exynos5_gpio_part1 *) samsung_get_base_gpio_part1(); - struct exynos5_gpio_part2 *gpio2 = - (struct exynos5_gpio_part2 *) samsung_get_base_gpio_part2(); switch (peripheral) { case PERIPH_ID_SPI0: - bank = &gpio1->a2; - cfg = GPIO_FUNC(0x2); - pin = 0; + cfg = S5P_GPIO_FUNC(0x2); + pin = EXYNOS5_GPIO_A20; break; case PERIPH_ID_SPI1: - bank = &gpio1->a2; - cfg = GPIO_FUNC(0x2); - pin = 4; + cfg = S5P_GPIO_FUNC(0x2); + pin = EXYNOS5_GPIO_A24; break; case PERIPH_ID_SPI2: - bank = &gpio1->b1; - cfg = GPIO_FUNC(0x5); - pin = 1; + cfg = S5P_GPIO_FUNC(0x5); + pin = EXYNOS5_GPIO_B11; break; case PERIPH_ID_SPI3: - bank = &gpio2->f1; - cfg = GPIO_FUNC(0x2); - pin = 0; + cfg = S5P_GPIO_FUNC(0x2); + pin = EXYNOS5_GPIO_F10; break; case PERIPH_ID_SPI4: for (i = 0; i < 2; i++) { - s5p_gpio_cfg_pin(&gpio2->f0, i + 2, GPIO_FUNC(0x4)); - s5p_gpio_cfg_pin(&gpio2->e0, i + 4, GPIO_FUNC(0x4)); + gpio_cfg_pin(EXYNOS5_GPIO_F02 + i, S5P_GPIO_FUNC(0x4)); + gpio_cfg_pin(EXYNOS5_GPIO_E04 + i, S5P_GPIO_FUNC(0x4)); } break; } if (peripheral != PERIPH_ID_SPI4) { for (i = pin; i < pin + 4; i++) - s5p_gpio_cfg_pin(bank, i, cfg); + gpio_cfg_pin(i, cfg); } } void exynos5420_spi_config(int peripheral) { int cfg, pin, i; - struct s5p_gpio_bank *bank = NULL; - struct exynos5420_gpio_part1 *gpio1 = - (struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1(); - struct exynos5420_gpio_part4 *gpio4 = - (struct exynos5420_gpio_part4 *)samsung_get_base_gpio_part4(); switch (peripheral) { case PERIPH_ID_SPI0: - bank = &gpio1->a2; - cfg = GPIO_FUNC(0x2); - pin = 0; + pin = EXYNOS5420_GPIO_A20; + cfg = S5P_GPIO_FUNC(0x2); break; case PERIPH_ID_SPI1: - bank = &gpio1->a2; - cfg = GPIO_FUNC(0x2); - pin = 4; + pin = EXYNOS5420_GPIO_A24; + cfg = S5P_GPIO_FUNC(0x2); break; case PERIPH_ID_SPI2: - bank = &gpio1->b1; - cfg = GPIO_FUNC(0x5); - pin = 1; + pin = EXYNOS5420_GPIO_B11; + cfg = S5P_GPIO_FUNC(0x5); break; case PERIPH_ID_SPI3: - bank = &gpio4->f1; - cfg = GPIO_FUNC(0x2); - pin = 0; + pin = EXYNOS5420_GPIO_F10; + cfg = S5P_GPIO_FUNC(0x2); break; case PERIPH_ID_SPI4: cfg = 0; @@ -489,11 +433,13 @@ void exynos5420_spi_config(int peripheral) if (peripheral != PERIPH_ID_SPI4) { for (i = pin; i < pin + 4; i++) - s5p_gpio_cfg_pin(bank, i, cfg); + gpio_cfg_pin(i, cfg); } else { for (i = 0; i < 2; i++) { - s5p_gpio_cfg_pin(&gpio4->f0, i + 2, GPIO_FUNC(0x4)); - s5p_gpio_cfg_pin(&gpio4->e0, i + 4, GPIO_FUNC(0x4)); + gpio_cfg_pin(EXYNOS5420_GPIO_F02 + i, + S5P_GPIO_FUNC(0x4)); + gpio_cfg_pin(EXYNOS5420_GPIO_E04 + i, + S5P_GPIO_FUNC(0x4)); } } } @@ -588,76 +534,70 @@ static int exynos5420_pinmux_config(int peripheral, int flags) static void exynos4_i2c_config(int peripheral, int flags) { - struct exynos4_gpio_part1 *gpio1 = - (struct exynos4_gpio_part1 *) samsung_get_base_gpio_part1(); - switch (peripheral) { case PERIPH_ID_I2C0: - s5p_gpio_cfg_pin(&gpio1->d1, 0, GPIO_FUNC(0x2)); - s5p_gpio_cfg_pin(&gpio1->d1, 1, GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS4_GPIO_D10, S5P_GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS4_GPIO_D11, S5P_GPIO_FUNC(0x2)); break; case PERIPH_ID_I2C1: - s5p_gpio_cfg_pin(&gpio1->d1, 2, GPIO_FUNC(0x2)); - s5p_gpio_cfg_pin(&gpio1->d1, 3, GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS4_GPIO_D12, S5P_GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS4_GPIO_D13, S5P_GPIO_FUNC(0x2)); break; case PERIPH_ID_I2C2: - s5p_gpio_cfg_pin(&gpio1->a0, 6, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->a0, 7, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4_GPIO_A06, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4_GPIO_A07, S5P_GPIO_FUNC(0x3)); break; case PERIPH_ID_I2C3: - s5p_gpio_cfg_pin(&gpio1->a1, 2, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->a1, 3, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4_GPIO_A12, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4_GPIO_A13, S5P_GPIO_FUNC(0x3)); break; case PERIPH_ID_I2C4: - s5p_gpio_cfg_pin(&gpio1->b, 2, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->b, 3, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4_GPIO_B2, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4_GPIO_B3, S5P_GPIO_FUNC(0x3)); break; case PERIPH_ID_I2C5: - s5p_gpio_cfg_pin(&gpio1->b, 6, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->b, 7, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4_GPIO_B6, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4_GPIO_B7, S5P_GPIO_FUNC(0x3)); break; case PERIPH_ID_I2C6: - s5p_gpio_cfg_pin(&gpio1->c1, 3, GPIO_FUNC(0x4)); - s5p_gpio_cfg_pin(&gpio1->c1, 4, GPIO_FUNC(0x4)); + gpio_cfg_pin(EXYNOS4_GPIO_C13, S5P_GPIO_FUNC(0x4)); + gpio_cfg_pin(EXYNOS4_GPIO_C14, S5P_GPIO_FUNC(0x4)); break; case PERIPH_ID_I2C7: - s5p_gpio_cfg_pin(&gpio1->d0, 2, GPIO_FUNC(0x3)); - s5p_gpio_cfg_pin(&gpio1->d0, 3, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4_GPIO_D02, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4_GPIO_D03, S5P_GPIO_FUNC(0x3)); break; } } static int exynos4_mmc_config(int peripheral, int flags) { - struct exynos4_gpio_part2 *gpio2 = - (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); - struct s5p_gpio_bank *bank, *bank_ext; - int i; + int i, start = 0, start_ext = 0; switch (peripheral) { case PERIPH_ID_SDMMC0: - bank = &gpio2->k0; - bank_ext = &gpio2->k1; + start = EXYNOS4_GPIO_K00; + start_ext = EXYNOS4_GPIO_K13; break; case PERIPH_ID_SDMMC2: - bank = &gpio2->k2; - bank_ext = &gpio2->k3; + start = EXYNOS4_GPIO_K20; + start_ext = EXYNOS4_GPIO_K33; break; default: return -1; } - for (i = 0; i < 7; i++) { - if (i == 2) + for (i = start; i < (start + 7); i++) { + if (i == (start + 2)) continue; - s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2)); - s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE); - s5p_gpio_set_drv(bank, i, GPIO_DRV_4X); + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x2)); + gpio_set_pull(i, S5P_GPIO_PULL_NONE); + gpio_set_drv(i, S5P_GPIO_DRV_4X); } if (flags & PINMUX_FLAG_8BIT_MODE) { - for (i = 3; i < 7; i++) { - s5p_gpio_cfg_pin(bank_ext, i, GPIO_FUNC(0x3)); - s5p_gpio_set_pull(bank_ext, i, GPIO_PULL_NONE); - s5p_gpio_set_drv(bank_ext, i, GPIO_DRV_4X); + for (i = start_ext; i < (start_ext + 4); i++) { + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x3)); + gpio_set_pull(i, S5P_GPIO_PULL_NONE); + gpio_set_drv(i, S5P_GPIO_DRV_4X); } } @@ -666,41 +606,138 @@ static int exynos4_mmc_config(int peripheral, int flags) static void exynos4_uart_config(int peripheral) { - struct exynos4_gpio_part1 *gpio1 = - (struct exynos4_gpio_part1 *)samsung_get_base_gpio_part1(); - struct s5p_gpio_bank *bank; int i, start, count; switch (peripheral) { case PERIPH_ID_UART0: - bank = &gpio1->a0; - start = 0; + start = EXYNOS4_GPIO_A00; count = 4; break; case PERIPH_ID_UART1: - bank = &gpio1->a0; - start = 4; + start = EXYNOS4_GPIO_A04; count = 4; break; case PERIPH_ID_UART2: - bank = &gpio1->a1; - start = 0; + start = EXYNOS4_GPIO_A10; count = 4; break; case PERIPH_ID_UART3: - bank = &gpio1->a1; - start = 4; + start = EXYNOS4_GPIO_A14; count = 2; break; default: debug("%s: invalid peripheral %d", __func__, peripheral); return; } - for (i = start; i < start + count; i++) { - s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE); - s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2)); + for (i = start; i < (start + count); i++) { + gpio_set_pull(i, S5P_GPIO_PULL_NONE); + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x2)); + } +} + +static void exynos4x12_i2c_config(int peripheral, int flags) +{ + switch (peripheral) { + case PERIPH_ID_I2C0: + gpio_cfg_pin(EXYNOS4X12_GPIO_D10, S5P_GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS4X12_GPIO_D11, S5P_GPIO_FUNC(0x2)); + break; + case PERIPH_ID_I2C1: + gpio_cfg_pin(EXYNOS4X12_GPIO_D12, S5P_GPIO_FUNC(0x2)); + gpio_cfg_pin(EXYNOS4X12_GPIO_D13, S5P_GPIO_FUNC(0x2)); + break; + case PERIPH_ID_I2C2: + gpio_cfg_pin(EXYNOS4X12_GPIO_A06, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4X12_GPIO_A07, S5P_GPIO_FUNC(0x3)); + break; + case PERIPH_ID_I2C3: + gpio_cfg_pin(EXYNOS4X12_GPIO_A12, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4X12_GPIO_A13, S5P_GPIO_FUNC(0x3)); + break; + case PERIPH_ID_I2C4: + gpio_cfg_pin(EXYNOS4X12_GPIO_B2, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4X12_GPIO_B3, S5P_GPIO_FUNC(0x3)); + break; + case PERIPH_ID_I2C5: + gpio_cfg_pin(EXYNOS4X12_GPIO_B6, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4X12_GPIO_B7, S5P_GPIO_FUNC(0x3)); + break; + case PERIPH_ID_I2C6: + gpio_cfg_pin(EXYNOS4X12_GPIO_C13, S5P_GPIO_FUNC(0x4)); + gpio_cfg_pin(EXYNOS4X12_GPIO_C14, S5P_GPIO_FUNC(0x4)); + break; + case PERIPH_ID_I2C7: + gpio_cfg_pin(EXYNOS4X12_GPIO_D02, S5P_GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS4X12_GPIO_D03, S5P_GPIO_FUNC(0x3)); + break; + } +} + +static int exynos4x12_mmc_config(int peripheral, int flags) +{ + int i, start = 0, start_ext = 0; + + switch (peripheral) { + case PERIPH_ID_SDMMC0: + start = EXYNOS4X12_GPIO_K00; + start_ext = EXYNOS4X12_GPIO_K13; + break; + case PERIPH_ID_SDMMC2: + start = EXYNOS4X12_GPIO_K20; + start_ext = EXYNOS4X12_GPIO_K33; + break; + default: + return -1; } + for (i = start; i < (start + 7); i++) { + if (i == (start + 2)) + continue; + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x2)); + gpio_set_pull(i, S5P_GPIO_PULL_NONE); + gpio_set_drv(i, S5P_GPIO_DRV_4X); + } + if (flags & PINMUX_FLAG_8BIT_MODE) { + for (i = start_ext; i < (start_ext + 4); i++) { + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x3)); + gpio_set_pull(i, S5P_GPIO_PULL_NONE); + gpio_set_drv(i, S5P_GPIO_DRV_4X); + } + } + + return 0; } + +static void exynos4x12_uart_config(int peripheral) +{ + int i, start, count; + + switch (peripheral) { + case PERIPH_ID_UART0: + start = EXYNOS4X12_GPIO_A00; + count = 4; + break; + case PERIPH_ID_UART1: + start = EXYNOS4X12_GPIO_A04; + count = 4; + break; + case PERIPH_ID_UART2: + start = EXYNOS4X12_GPIO_A10; + count = 4; + break; + case PERIPH_ID_UART3: + start = EXYNOS4X12_GPIO_A14; + count = 2; + break; + default: + debug("%s: invalid peripheral %d", __func__, peripheral); + return; + } + for (i = start; i < (start + count); i++) { + gpio_set_pull(i, S5P_GPIO_PULL_NONE); + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x2)); + } +} + static int exynos4_pinmux_config(int peripheral, int flags) { switch (peripheral) { @@ -736,6 +773,41 @@ static int exynos4_pinmux_config(int peripheral, int flags) return 0; } +static int exynos4x12_pinmux_config(int peripheral, int flags) +{ + switch (peripheral) { + case PERIPH_ID_UART0: + case PERIPH_ID_UART1: + case PERIPH_ID_UART2: + case PERIPH_ID_UART3: + exynos4x12_uart_config(peripheral); + break; + case PERIPH_ID_I2C0: + case PERIPH_ID_I2C1: + case PERIPH_ID_I2C2: + case PERIPH_ID_I2C3: + case PERIPH_ID_I2C4: + case PERIPH_ID_I2C5: + case PERIPH_ID_I2C6: + case PERIPH_ID_I2C7: + exynos4x12_i2c_config(peripheral, flags); + break; + case PERIPH_ID_SDMMC0: + case PERIPH_ID_SDMMC2: + return exynos4x12_mmc_config(peripheral, flags); + case PERIPH_ID_SDMMC1: + case PERIPH_ID_SDMMC3: + case PERIPH_ID_SDMMC4: + debug("SDMMC device %d not implemented\n", peripheral); + return -1; + default: + debug("%s: invalid peripheral %d", __func__, peripheral); + return -1; + } + + return 0; +} + int exynos_pinmux_config(int peripheral, int flags) { if (cpu_is_exynos5()) { @@ -744,11 +816,14 @@ int exynos_pinmux_config(int peripheral, int flags) else if (proid_is_exynos5250()) return exynos5_pinmux_config(peripheral, flags); } else if (cpu_is_exynos4()) { - return exynos4_pinmux_config(peripheral, flags); - } else { - debug("pinmux functionality not supported\n"); + if (proid_is_exynos4412()) + return exynos4x12_pinmux_config(peripheral, flags); + else + return exynos4_pinmux_config(peripheral, flags); } + debug("pinmux functionality not supported\n"); + return -1; } @@ -787,7 +862,7 @@ int pinmux_decode_periph_id(const void *blob, int node) return exynos5_pinmux_decode_periph_id(blob, node); else if (cpu_is_exynos4()) return exynos4_pinmux_decode_periph_id(blob, node); - else - return PERIPH_ID_NONE; + + return PERIPH_ID_NONE; } #endif diff --git a/arch/arm/cpu/armv7/rmobile/Makefile b/arch/arm/cpu/armv7/rmobile/Makefile index 22219990dd..fad004ca64 100644 --- a/arch/arm/cpu/armv7/rmobile/Makefile +++ b/arch/arm/cpu/armv7/rmobile/Makefile @@ -11,7 +11,7 @@ obj-y += emac.o obj-$(CONFIG_DISPLAY_BOARDINFO) += board.o obj-$(CONFIG_GLOBAL_TIMER) += timer.o obj-$(CONFIG_R8A7740) += lowlevel_init.o cpu_info-r8a7740.o pfc-r8a7740.o -obj-$(CONFIG_R8A7790) += lowlevel_init_ca15.o cpu_info-r8a7790.o pfc-r8a7790.o -obj-$(CONFIG_R8A7791) += lowlevel_init_ca15.o cpu_info-r8a7791.o pfc-r8a7791.o +obj-$(CONFIG_R8A7790) += lowlevel_init_ca15.o cpu_info-rcar.o pfc-r8a7790.o +obj-$(CONFIG_R8A7791) += lowlevel_init_ca15.o cpu_info-rcar.o pfc-r8a7791.o obj-$(CONFIG_SH73A0) += lowlevel_init.o cpu_info-sh73a0.o pfc-sh73a0.o obj-$(CONFIG_TMU_TIMER) += ../../../../sh/lib/time.o diff --git a/arch/arm/cpu/armv7/rmobile/cpu_info-r8a7791.c b/arch/arm/cpu/armv7/rmobile/cpu_info-r8a7791.c deleted file mode 100644 index 2de58ed273..0000000000 --- a/arch/arm/cpu/armv7/rmobile/cpu_info-r8a7791.c +++ /dev/null @@ -1,29 +0,0 @@ -/* - * arch/arm/cpu/armv7/rmobile/cpu_info-r8a7791.c - * - * Copyright (C) 2013 Renesas Electronics Corporation - * - * SPDX-License-Identifier: GPL-2.0 - */ -#include <common.h> -#include <asm/io.h> - -#define PRR 0xFF000044 - -u32 rmobile_get_cpu_type(void) -{ - u32 product; - - product = readl(PRR); - - return (u32)((product & 0x00007F00) >> 8); -} - -u32 rmobile_get_cpu_rev_integer(void) -{ - u32 product; - - product = readl(PRR); - - return (u32)((product & 0x000000F0) >> 4); -} diff --git a/arch/arm/cpu/armv7/rmobile/cpu_info-r8a7790.c b/arch/arm/cpu/armv7/rmobile/cpu_info-rcar.c index 7232e23774..42ee30fbe7 100644 --- a/arch/arm/cpu/armv7/rmobile/cpu_info-r8a7790.c +++ b/arch/arm/cpu/armv7/rmobile/cpu_info-rcar.c @@ -1,8 +1,7 @@ /* - * arch/arm/cpu/armv7/rmobile/cpu_info-r8a7790.c - * This file is r8a7790 processor support. + * arch/arm/cpu/armv7/rmobile/cpu_info-rcar.c * - * Copyright (C) 2013 Renesas Electronics Corporation + * Copyright (C) 2013,2014 Renesas Electronics Corporation * * SPDX-License-Identifier: GPL-2.0 */ @@ -18,5 +17,10 @@ u32 rmobile_get_cpu_type(void) u32 rmobile_get_cpu_rev_integer(void) { - return (readl(PRR) & 0x000000F0) >> 4; + return ((readl(PRR) & 0x000000F0) >> 4) + 1; +} + +u32 rmobile_get_cpu_rev_fraction(void) +{ + return readl(PRR) & 0x0000000F; } diff --git a/arch/arm/cpu/armv7/rmobile/cpu_info.c b/arch/arm/cpu/armv7/rmobile/cpu_info.c index 83d5282e3e..7a7c97d791 100644 --- a/arch/arm/cpu/armv7/rmobile/cpu_info.c +++ b/arch/arm/cpu/armv7/rmobile/cpu_info.c @@ -44,35 +44,30 @@ static u32 __rmobile_get_cpu_rev_fraction(void) u32 rmobile_get_cpu_rev_fraction(void) __attribute__((weak, alias("__rmobile_get_cpu_rev_fraction"))); +/* CPU infomation table */ +static const struct { + u16 cpu_type; + u8 cpu_name[10]; +} rmobile_cpuinfo[] = { + { 0x37, "SH73A0" }, + { 0x40, "R8A7740" }, + { 0x45, "R8A7790" }, + { 0x47, "R8A7791" }, + { 0x0, "CPU" }, +}; + int print_cpuinfo(void) { - switch (rmobile_get_cpu_type()) { - case 0x37: - printf("CPU: Renesas Electronics SH73A0 rev %d.%d\n", - rmobile_get_cpu_rev_integer(), - rmobile_get_cpu_rev_fraction()); - break; - case 0x40: - printf("CPU: Renesas Electronics R8A7740 rev %d.%d\n", - rmobile_get_cpu_rev_integer(), - rmobile_get_cpu_rev_fraction()); - break; - - case 0x45: - printf("CPU: Renesas Electronics R8A7790 rev %d\n", - rmobile_get_cpu_rev_integer()); - break; - - case 0x47: - printf("CPU: Renesas Electronics R8A7791 rev %d\n", - rmobile_get_cpu_rev_integer()); - break; - - default: - printf("CPU: Renesas Electronics CPU rev %d.%d\n", - rmobile_get_cpu_rev_integer(), - rmobile_get_cpu_rev_fraction()); - break; + int i = 0; + u32 cpu_type = rmobile_get_cpu_type(); + for (; i < ARRAY_SIZE(rmobile_cpuinfo); i++) { + if (rmobile_cpuinfo[i].cpu_type == cpu_type) { + printf("CPU: Renesas Electronics %s rev %d.%d\n", + rmobile_cpuinfo[i].cpu_name, + rmobile_get_cpu_rev_integer(), + rmobile_get_cpu_rev_fraction()); + break; + } } return 0; } diff --git a/arch/arm/cpu/armv7/rmobile/lowlevel_init_ca15.S b/arch/arm/cpu/armv7/rmobile/lowlevel_init_ca15.S index e07cc8093a..287f8d74af 100644 --- a/arch/arm/cpu/armv7/rmobile/lowlevel_init_ca15.S +++ b/arch/arm/cpu/armv7/rmobile/lowlevel_init_ca15.S @@ -2,7 +2,7 @@ * arch/arm/cpu/armv7/rmobile/lowlevel_init_ca15.S * This file is lager low level initialize. * - * Copyright (C) 2013 Renesas Electronics Corporation + * Copyright (C) 2013, 2014 Renesas Electronics Corporation * * SPDX-License-Identifier: GPL-2.0 */ @@ -36,16 +36,32 @@ do_cpu_waiting: .align 4 do_lowlevel_init: /* surpress wfe if ca15 */ - tst r4, #4 + tst r4, #4 mrceq p15, 0, r0, c1, c0, 1 /* actlr */ orreq r0, r0, #(1<<7) mcreq p15, 0, r0, c1, c0, 1 + /* and set l2 latency */ mrceq p15, 1, r0, c9, c0, 2 /* l2ctlr */ orreq r0, r0, #0x00000800 orreq r0, r0, #0x00000003 mcreq p15, 1, r0, c9, c0, 2 + mrc p15, 0, r0, c0, c0, 5 /* r0 = MPIDR */ + and r0, r0, #0xf00 + lsr r0, r0, #8 + tst r0, #1 /* only need for cluster 0 */ + bne _exit_init_l2_a15 + + mrc p15, 1, r0, c9, c0, 2 /* r0 = L2CTLR */ + and r1, r0, #7 + cmp r1, #3 /* has already been set up */ + bicne r0, r0, #0xe7 + orrne r0, r0, #0x83 /* L2CTLR[7:6] + L2CTLR[2:0] */ + orrne r0, r0, #0x20 /* L2CTLR[5] */ + mcrne p15, 1, r0, c9, c0, 2 + +_exit_init_l2_a15: ldr r3, =(CONFIG_SYS_INIT_SP_ADDR) sub sp, r3, #4 str lr, [sp] diff --git a/arch/arm/cpu/armv7/socfpga/lowlevel_init.S b/arch/arm/cpu/armv7/socfpga/lowlevel_init.S index 1caaa2759f..2f2e9fcc7c 100644 --- a/arch/arm/cpu/armv7/socfpga/lowlevel_init.S +++ b/arch/arm/cpu/armv7/socfpga/lowlevel_init.S @@ -10,20 +10,7 @@ /* Save the parameter pass in by previous boot loader */ .global save_boot_params save_boot_params: - /* save the parameter here */ - - /* - * Setup stack for exception, which is located - * at the end of on-chip RAM. We don't expect exception prior to - * relocation and if that happens, we won't worry -- it will overide - * global data region as the code will goto reset. After relocation, - * this region won't be used by other part of program. - * Hence it is safe. - */ - ldr r0, =(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE) - ldr r1, =IRQ_STACK_START_IN - str r0, [r1] - + /* no parameter to save */ bx lr diff --git a/arch/arm/cpu/armv7/start.S b/arch/arm/cpu/armv7/start.S index 27be451a89..fedd7c8f7e 100644 --- a/arch/arm/cpu/armv7/start.S +++ b/arch/arm/cpu/armv7/start.S @@ -19,46 +19,6 @@ #include <asm/system.h> #include <linux/linkage.h> -.globl _start -_start: b reset - ldr pc, _undefined_instruction - ldr pc, _software_interrupt - ldr pc, _prefetch_abort - ldr pc, _data_abort - ldr pc, _not_used - ldr pc, _irq - ldr pc, _fiq -#ifdef CONFIG_SPL_BUILD -_undefined_instruction: .word _undefined_instruction -_software_interrupt: .word _software_interrupt -_prefetch_abort: .word _prefetch_abort -_data_abort: .word _data_abort -_not_used: .word _not_used -_irq: .word _irq -_fiq: .word _fiq -_pad: .word 0x12345678 /* now 16*4=64 */ -#else -.globl _undefined_instruction -_undefined_instruction: .word undefined_instruction -.globl _software_interrupt -_software_interrupt: .word software_interrupt -.globl _prefetch_abort -_prefetch_abort: .word prefetch_abort -.globl _data_abort -_data_abort: .word data_abort -.globl _not_used -_not_used: .word not_used -.globl _irq -_irq: .word irq -.globl _fiq -_fiq: .word fiq -_pad: .word 0x12345678 /* now 16*4=64 */ -#endif /* CONFIG_SPL_BUILD */ - -.global _end_vect -_end_vect: - - .balignl 16,0xdeadbeef /************************************************************************* * * Startup Code (reset vector) @@ -70,26 +30,7 @@ _end_vect: * *************************************************************************/ -#ifdef CONFIG_USE_IRQ -/* IRQ stack memory (calculated at run-time) */ -.globl IRQ_STACK_START -IRQ_STACK_START: - .word 0x0badc0de - -/* IRQ stack memory (calculated at run-time) */ -.globl FIQ_STACK_START -FIQ_STACK_START: - .word 0x0badc0de -#endif - -/* IRQ stack memory (calculated at run-time) + 8 bytes */ -.globl IRQ_STACK_START_IN -IRQ_STACK_START_IN: - .word 0x0badc0de - -/* - * the actual reset code - */ + .globl reset reset: bl save_boot_params @@ -250,195 +191,3 @@ ENTRY(cpu_init_crit) b lowlevel_init @ go setup pll,mux,memory ENDPROC(cpu_init_crit) #endif - -#ifndef CONFIG_SPL_BUILD -/* - ************************************************************************* - * - * Interrupt handling - * - ************************************************************************* - */ -@ -@ IRQ stack frame. -@ -#define S_FRAME_SIZE 72 - -#define S_OLD_R0 68 -#define S_PSR 64 -#define S_PC 60 -#define S_LR 56 -#define S_SP 52 - -#define S_IP 48 -#define S_FP 44 -#define S_R10 40 -#define S_R9 36 -#define S_R8 32 -#define S_R7 28 -#define S_R6 24 -#define S_R5 20 -#define S_R4 16 -#define S_R3 12 -#define S_R2 8 -#define S_R1 4 -#define S_R0 0 - -#define MODE_SVC 0x13 -#define I_BIT 0x80 - -/* - * use bad_save_user_regs for abort/prefetch/undef/swi ... - * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling - */ - - .macro bad_save_user_regs - sub sp, sp, #S_FRAME_SIZE @ carve out a frame on current - @ user stack - stmia sp, {r0 - r12} @ Save user registers (now in - @ svc mode) r0-r12 - ldr r2, IRQ_STACK_START_IN @ set base 2 words into abort - @ stack - ldmia r2, {r2 - r3} @ get values for "aborted" pc - @ and cpsr (into parm regs) - add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack - - add r5, sp, #S_SP - mov r1, lr - stmia r5, {r0 - r3} @ save sp_SVC, lr_SVC, pc, cpsr - mov r0, sp @ save current stack into r0 - @ (param register) - .endm - - .macro irq_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - add r8, sp, #S_PC @ !! R8 NEEDS to be saved !! - @ a reserved stack spot would - @ be good. - stmdb r8, {sp, lr}^ @ Calling SP, LR - str lr, [r8, #0] @ Save calling PC - mrs r6, spsr - str r6, [r8, #4] @ Save CPSR - str r0, [r8, #8] @ Save OLD_R0 - mov r0, sp - .endm - - .macro irq_restore_user_regs - ldmia sp, {r0 - lr}^ @ Calling r0 - lr - mov r0, r0 - ldr lr, [sp, #S_PC] @ Get PC - add sp, sp, #S_FRAME_SIZE - subs pc, lr, #4 @ return & move spsr_svc into - @ cpsr - .endm - - .macro get_bad_stack - ldr r13, IRQ_STACK_START_IN @ setup our mode stack (enter - @ in banked mode) - - str lr, [r13] @ save caller lr in position 0 - @ of saved stack - mrs lr, spsr @ get the spsr - str lr, [r13, #4] @ save spsr in position 1 of - @ saved stack - - mov r13, #MODE_SVC @ prepare SVC-Mode - @ msr spsr_c, r13 - msr spsr, r13 @ switch modes, make sure - @ moves will execute - mov lr, pc @ capture return pc - movs pc, lr @ jump to next instruction & - @ switch modes. - .endm - - .macro get_bad_stack_swi - sub r13, r13, #4 @ space on current stack for - @ scratch reg. - str r0, [r13] @ save R0's value. - ldr r0, IRQ_STACK_START_IN @ get data regions start - @ spots for abort stack - str lr, [r0] @ save caller lr in position 0 - @ of saved stack - mrs lr, spsr @ get the spsr - str lr, [r0, #4] @ save spsr in position 1 of - @ saved stack - ldr lr, [r0] @ restore lr - ldr r0, [r13] @ restore r0 - add r13, r13, #4 @ pop stack entry - .endm - - .macro get_irq_stack @ setup IRQ stack - ldr sp, IRQ_STACK_START - .endm - - .macro get_fiq_stack @ setup FIQ stack - ldr sp, FIQ_STACK_START - .endm - -/* - * exception handlers - */ - .align 5 -undefined_instruction: - get_bad_stack - bad_save_user_regs - bl do_undefined_instruction - - .align 5 -software_interrupt: - get_bad_stack_swi - bad_save_user_regs - bl do_software_interrupt - - .align 5 -prefetch_abort: - get_bad_stack - bad_save_user_regs - bl do_prefetch_abort - - .align 5 -data_abort: - get_bad_stack - bad_save_user_regs - bl do_data_abort - - .align 5 -not_used: - get_bad_stack - bad_save_user_regs - bl do_not_used - -#ifdef CONFIG_USE_IRQ - - .align 5 -irq: - get_irq_stack - irq_save_user_regs - bl do_irq - irq_restore_user_regs - - .align 5 -fiq: - get_fiq_stack - /* someone ought to write a more effective fiq_save_user_regs */ - irq_save_user_regs - bl do_fiq - irq_restore_user_regs - -#else - - .align 5 -irq: - get_bad_stack - bad_save_user_regs - bl do_irq - - .align 5 -fiq: - get_bad_stack - bad_save_user_regs - bl do_fiq - -#endif /* CONFIG_USE_IRQ */ -#endif /* CONFIG_SPL_BUILD */ diff --git a/arch/arm/cpu/armv7/zynq/u-boot.lds b/arch/arm/cpu/armv7/zynq/u-boot.lds index f2a5965988..69500a64e2 100644 --- a/arch/arm/cpu/armv7/zynq/u-boot.lds +++ b/arch/arm/cpu/armv7/zynq/u-boot.lds @@ -88,7 +88,7 @@ SECTIONS } /* - * Zynq needs to discard more sections because the user + * Zynq needs to discard these sections because the user * is expected to pass this image on to tools for boot.bin * generation that require them to be dropped. */ diff --git a/arch/arm/cpu/pxa/cpuinfo.c b/arch/arm/cpu/pxa/cpuinfo.c index 9d16079956..17d8be5b5b 100644 --- a/arch/arm/cpu/pxa/cpuinfo.c +++ b/arch/arm/cpu/pxa/cpuinfo.c @@ -11,6 +11,12 @@ #include <errno.h> #include <linux/compiler.h> +#ifdef CONFIG_CPU_PXA25X +#if ((CONFIG_SYS_INIT_SP_ADDR) != 0xfffff800) +#error "Init SP address must be set to 0xfffff800 for PXA250" +#endif +#endif + #define CPU_MASK_PXA_PRODID 0x000003f0 #define CPU_MASK_PXA_REVID 0x0000000f diff --git a/arch/arm/cpu/pxa/start.S b/arch/arm/cpu/pxa/start.S index ae0d13ce8f..c77d51e6d8 100644 --- a/arch/arm/cpu/pxa/start.S +++ b/arch/arm/cpu/pxa/start.S @@ -23,54 +23,6 @@ #include <config.h> #include <version.h> -#ifdef CONFIG_CPU_PXA25X -#if ((CONFIG_SYS_INIT_SP_ADDR) != 0xfffff800) -#error "Init SP address must be set to 0xfffff800 for PXA250" -#endif -#endif - -.globl _start -_start: b reset -#ifdef CONFIG_SPL_BUILD - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - ldr pc, _hang - -_hang: - .word do_hang - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 - .word 0x12345678 /* now 16*4=64 */ -#else - ldr pc, _undefined_instruction - ldr pc, _software_interrupt - ldr pc, _prefetch_abort - ldr pc, _data_abort - ldr pc, _not_used - ldr pc, _irq - ldr pc, _fiq - -_undefined_instruction: .word undefined_instruction -_software_interrupt: .word software_interrupt -_prefetch_abort: .word prefetch_abort -_data_abort: .word data_abort -_not_used: .word not_used -_irq: .word irq -_fiq: .word fiq -_pad: .word 0x12345678 /* now 16*4=64 */ -#endif /* CONFIG_SPL_BUILD */ -.global _end_vect -_end_vect: - - .balignl 16,0xdeadbeef /* ************************************************************************* * @@ -84,26 +36,7 @@ _end_vect: ************************************************************************* */ -#ifdef CONFIG_USE_IRQ -/* IRQ stack memory (calculated at run-time) */ -.globl IRQ_STACK_START -IRQ_STACK_START: - .word 0x0badc0de - -/* IRQ stack memory (calculated at run-time) */ -.globl FIQ_STACK_START -FIQ_STACK_START: - .word 0x0badc0de -#endif - -/* IRQ stack memory (calculated at run-time) + 8 bytes */ -.globl IRQ_STACK_START_IN -IRQ_STACK_START_IN: - .word 0x0badc0de - -/* - * the actual reset code - */ + .globl reset reset: /* @@ -174,190 +107,6 @@ cpu_init_crit: mov pc, lr /* back to my caller */ #endif /* !CONFIG_SKIP_LOWLEVEL_INIT || CONFIG_CPU_PXA25X */ -#ifndef CONFIG_SPL_BUILD -/* - ************************************************************************* - * - * Interrupt handling - * - ************************************************************************* - */ -@ -@ IRQ stack frame. -@ -#define S_FRAME_SIZE 72 - -#define S_OLD_R0 68 -#define S_PSR 64 -#define S_PC 60 -#define S_LR 56 -#define S_SP 52 - -#define S_IP 48 -#define S_FP 44 -#define S_R10 40 -#define S_R9 36 -#define S_R8 32 -#define S_R7 28 -#define S_R6 24 -#define S_R5 20 -#define S_R4 16 -#define S_R3 12 -#define S_R2 8 -#define S_R1 4 -#define S_R0 0 - -#define MODE_SVC 0x13 -#define I_BIT 0x80 - -/* - * use bad_save_user_regs for abort/prefetch/undef/swi ... - * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling - */ - - .macro bad_save_user_regs - sub sp, sp, #S_FRAME_SIZE @ carve out a frame on current user stack - stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12 - - ldr r2, IRQ_STACK_START_IN @ set base 2 words into abort stack - ldmia r2, {r2 - r3} @ get values for "aborted" pc and cpsr (into parm regs) - add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack - - add r5, sp, #S_SP - mov r1, lr - stmia r5, {r0 - r3} @ save sp_SVC, lr_SVC, pc, cpsr - mov r0, sp @ save current stack into r0 (param register) - .endm - - .macro irq_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - add r8, sp, #S_PC @ !!!! R8 NEEDS to be saved !!!! a reserved stack spot would be good. - stmdb r8, {sp, lr}^ @ Calling SP, LR - str lr, [r8, #0] @ Save calling PC - mrs r6, spsr - str r6, [r8, #4] @ Save CPSR - str r0, [r8, #8] @ Save OLD_R0 - mov r0, sp - .endm - - .macro irq_restore_user_regs - ldmia sp, {r0 - lr}^ @ Calling r0 - lr - mov r0, r0 - ldr lr, [sp, #S_PC] @ Get PC - add sp, sp, #S_FRAME_SIZE - subs pc, lr, #4 @ return & move spsr_svc into cpsr - .endm - - .macro get_bad_stack - ldr r13, IRQ_STACK_START_IN @ setup our mode stack (enter in banked mode) - - str lr, [r13] @ save caller lr in position 0 of saved stack - mrs lr, spsr @ get the spsr - str lr, [r13, #4] @ save spsr in position 1 of saved stack - - mov r13, #MODE_SVC @ prepare SVC-Mode - @ msr spsr_c, r13 - msr spsr, r13 @ switch modes, make sure moves will execute - mov lr, pc @ capture return pc - movs pc, lr @ jump to next instruction & switch modes. - .endm - - .macro get_bad_stack_swi - sub r13, r13, #4 @ space on current stack for scratch reg. - str r0, [r13] @ save R0's value. - ldr r0, IRQ_STACK_START_IN @ get data regions start - str lr, [r0] @ save caller lr in position 0 of saved stack - mrs lr, spsr @ get the spsr - str lr, [r0, #4] @ save spsr in position 1 of saved stack - ldr lr, [r0] @ restore lr - ldr r0, [r13] @ restore r0 - add r13, r13, #4 @ pop stack entry - .endm - - .macro get_irq_stack @ setup IRQ stack - ldr sp, IRQ_STACK_START - .endm - - .macro get_fiq_stack @ setup FIQ stack - ldr sp, FIQ_STACK_START - .endm -#endif /* CONFIG_SPL_BUILD */ - -/* - * exception handlers - */ -#ifdef CONFIG_SPL_BUILD - .align 5 -do_hang: - bl hang /* hang and never return */ -#else /* !CONFIG_SPL_BUILD */ - .align 5 -undefined_instruction: - get_bad_stack - bad_save_user_regs - bl do_undefined_instruction - - .align 5 -software_interrupt: - get_bad_stack_swi - bad_save_user_regs - bl do_software_interrupt - - .align 5 -prefetch_abort: - get_bad_stack - bad_save_user_regs - bl do_prefetch_abort - - .align 5 -data_abort: - get_bad_stack - bad_save_user_regs - bl do_data_abort - - .align 5 -not_used: - get_bad_stack - bad_save_user_regs - bl do_not_used - -#ifdef CONFIG_USE_IRQ - - .align 5 -irq: - get_irq_stack - irq_save_user_regs - bl do_irq - irq_restore_user_regs - - .align 5 -fiq: - get_fiq_stack - /* someone ought to write a more effiction fiq_save_user_regs */ - irq_save_user_regs - bl do_fiq - irq_restore_user_regs - -#else - - .align 5 -irq: - get_bad_stack - bad_save_user_regs - bl do_irq - - .align 5 -fiq: - get_bad_stack - bad_save_user_regs - bl do_fiq - -#endif - .align 5 -#endif /* CONFIG_SPL_BUILD */ - - /* * Enable MMU to use DCache as DRAM. * diff --git a/arch/arm/cpu/sa1100/cpu.c b/arch/arm/cpu/sa1100/cpu.c index 6651898de2..4c9752a1c8 100644 --- a/arch/arm/cpu/sa1100/cpu.c +++ b/arch/arm/cpu/sa1100/cpu.c @@ -17,6 +17,7 @@ #include <common.h> #include <command.h> #include <asm/system.h> +#include <asm/io.h> #ifdef CONFIG_USE_IRQ DECLARE_GLOBAL_DATA_PTR; @@ -52,3 +53,16 @@ static void cache_flush (void) asm ("mcr p15, 0, %0, c7, c5, 0": :"r" (i)); } + +#define RST_BASE 0x90030000 +#define RSRR 0x00 +#define RCSR 0x04 + +__attribute__((noreturn)) void reset_cpu(ulong addr __attribute__((unused))) +{ + /* repeat endlessly */ + while (1) { + writel(0, RST_BASE + RCSR); + writel(1, RST_BASE + RSRR); + } +} diff --git a/arch/arm/cpu/sa1100/start.S b/arch/arm/cpu/sa1100/start.S index bf80937a7c..78e0cb8868 100644 --- a/arch/arm/cpu/sa1100/start.S +++ b/arch/arm/cpu/sa1100/start.S @@ -16,36 +16,6 @@ /* ************************************************************************* * - * Jump vector table as in table 3.1 in [1] - * - ************************************************************************* - */ - - -.globl _start -_start: b reset - ldr pc, _undefined_instruction - ldr pc, _software_interrupt - ldr pc, _prefetch_abort - ldr pc, _data_abort - ldr pc, _not_used - ldr pc, _irq - ldr pc, _fiq - -_undefined_instruction: .word undefined_instruction -_software_interrupt: .word software_interrupt -_prefetch_abort: .word prefetch_abort -_data_abort: .word data_abort -_not_used: .word not_used -_irq: .word irq -_fiq: .word fiq - - .balignl 16,0xdeadbeef - - -/* - ************************************************************************* - * * Startup Code (reset vector) * * do important init only if we don't start from memory! @@ -56,26 +26,7 @@ _fiq: .word fiq ************************************************************************* */ -#ifdef CONFIG_USE_IRQ -/* IRQ stack memory (calculated at run-time) */ -.globl IRQ_STACK_START -IRQ_STACK_START: - .word 0x0badc0de - -/* IRQ stack memory (calculated at run-time) */ -.globl FIQ_STACK_START -FIQ_STACK_START: - .word 0x0badc0de -#endif - -/* IRQ stack memory (calculated at run-time) + 8 bytes */ -.globl IRQ_STACK_START_IN -IRQ_STACK_START_IN: - .word 0x0badc0de - -/* - * the actual reset code - */ + .globl reset reset: /* @@ -173,177 +124,3 @@ cpu_init_crit: mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */ mov pc, lr - - -/* - ************************************************************************* - * - * Interrupt handling - * - ************************************************************************* - */ - -@ -@ IRQ stack frame. -@ -#define S_FRAME_SIZE 72 - -#define S_OLD_R0 68 -#define S_PSR 64 -#define S_PC 60 -#define S_LR 56 -#define S_SP 52 - -#define S_IP 48 -#define S_FP 44 -#define S_R10 40 -#define S_R9 36 -#define S_R8 32 -#define S_R7 28 -#define S_R6 24 -#define S_R5 20 -#define S_R4 16 -#define S_R3 12 -#define S_R2 8 -#define S_R1 4 -#define S_R0 0 - -#define MODE_SVC 0x13 -#define I_BIT 0x80 - -/* - * use bad_save_user_regs for abort/prefetch/undef/swi ... - * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling - */ - - .macro bad_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - add r8, sp, #S_PC - - ldr r2, IRQ_STACK_START_IN - ldmia r2, {r2 - r4} @ get pc, cpsr, old_r0 - add r0, sp, #S_FRAME_SIZE @ restore sp_SVC - - add r5, sp, #S_SP - mov r1, lr - stmia r5, {r0 - r4} @ save sp_SVC, lr_SVC, pc, cpsr, old_r - mov r0, sp - .endm - - .macro irq_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - add r8, sp, #S_PC - stmdb r8, {sp, lr}^ @ Calling SP, LR - str lr, [r8, #0] @ Save calling PC - mrs r6, spsr - str r6, [r8, #4] @ Save CPSR - str r0, [r8, #8] @ Save OLD_R0 - mov r0, sp - .endm - - .macro irq_restore_user_regs - ldmia sp, {r0 - lr}^ @ Calling r0 - lr - mov r0, r0 - ldr lr, [sp, #S_PC] @ Get PC - add sp, sp, #S_FRAME_SIZE - subs pc, lr, #4 @ return & move spsr_svc into cpsr - .endm - - .macro get_bad_stack - ldr r13, IRQ_STACK_START_IN @ setup our mode stack - - str lr, [r13] @ save caller lr / spsr - mrs lr, spsr - str lr, [r13, #4] - - mov r13, #MODE_SVC @ prepare SVC-Mode - msr spsr_c, r13 - mov lr, pc - movs pc, lr - .endm - - .macro get_irq_stack @ setup IRQ stack - ldr sp, IRQ_STACK_START - .endm - - .macro get_fiq_stack @ setup FIQ stack - ldr sp, FIQ_STACK_START - .endm - -/* - * exception handlers - */ - .align 5 -undefined_instruction: - get_bad_stack - bad_save_user_regs - bl do_undefined_instruction - - .align 5 -software_interrupt: - get_bad_stack - bad_save_user_regs - bl do_software_interrupt - - .align 5 -prefetch_abort: - get_bad_stack - bad_save_user_regs - bl do_prefetch_abort - - .align 5 -data_abort: - get_bad_stack - bad_save_user_regs - bl do_data_abort - - .align 5 -not_used: - get_bad_stack - bad_save_user_regs - bl do_not_used - -#ifdef CONFIG_USE_IRQ - - .align 5 -irq: - get_irq_stack - irq_save_user_regs - bl do_irq - irq_restore_user_regs - - .align 5 -fiq: - get_fiq_stack - /* someone ought to write a more effiction fiq_save_user_regs */ - irq_save_user_regs - bl do_fiq - irq_restore_user_regs - -#else - - .align 5 -irq: - get_bad_stack - bad_save_user_regs - bl do_irq - - .align 5 -fiq: - get_bad_stack - bad_save_user_regs - bl do_fiq - -#endif - - .align 5 -.globl reset_cpu -reset_cpu: - ldr r0, RST_BASE - mov r1, #0x0 @ set bit 3-0 ... - str r1, [r0, #RCSR] @ ... to clear in RCSR - mov r1, #0x1 - str r1, [r0, #RSRR] @ and perform reset - b reset_cpu @ silly, but repeat endlessly diff --git a/arch/arm/cpu/tegra-common/pinmux-common.c b/arch/arm/cpu/tegra-common/pinmux-common.c index d62618cd0f..6e3ab0c14c 100644 --- a/arch/arm/cpu/tegra-common/pinmux-common.c +++ b/arch/arm/cpu/tegra-common/pinmux-common.c @@ -86,12 +86,31 @@ #define IO_RESET_SHIFT 8 #define RCV_SEL_SHIFT 9 +#if !defined(CONFIG_TEGRA20) && !defined(CONFIG_TEGRA30) +/* This register/field only exists on Tegra114 and later */ +#define APB_MISC_PP_PINMUX_GLOBAL_0 0x40 +#define CLAMP_INPUTS_WHEN_TRISTATED 1 + +void pinmux_set_tristate_input_clamping(void) +{ + u32 *reg = _R(APB_MISC_PP_PINMUX_GLOBAL_0); + u32 val; + + val = readl(reg); + val |= CLAMP_INPUTS_WHEN_TRISTATED; + writel(val, reg); +} +#endif + void pinmux_set_func(enum pmux_pingrp pin, enum pmux_func func) { u32 *reg = MUX_REG(pin); int i, mux = -1; u32 val; + if (func == PMUX_FUNC_DEFAULT) + return; + /* Error check on pin and func */ assert(pmux_pingrp_isvalid(pin)); assert(pmux_func_isvalid(func)); diff --git a/arch/arm/cpu/u-boot-spl.lds b/arch/arm/cpu/u-boot-spl.lds index 3e886680e8..4beddf08e7 100644 --- a/arch/arm/cpu/u-boot-spl.lds +++ b/arch/arm/cpu/u-boot-spl.lds @@ -18,6 +18,7 @@ SECTIONS .text : { __image_copy_start = .; + *(.vectors) CPUDIR/start.o (.text*) *(.text*) } diff --git a/arch/arm/cpu/u-boot.lds b/arch/arm/cpu/u-boot.lds index 33c1f99fc0..a7728e0a2d 100644 --- a/arch/arm/cpu/u-boot.lds +++ b/arch/arm/cpu/u-boot.lds @@ -18,6 +18,7 @@ SECTIONS .text : { *(.__image_copy_start) + *(.vectors) CPUDIR/start.o (.text*) *(.text*) } diff --git a/arch/arm/dts/exynos4210-origen.dts b/arch/arm/dts/exynos4210-origen.dts index 5c9d2aed68..15059d2202 100644 --- a/arch/arm/dts/exynos4210-origen.dts +++ b/arch/arm/dts/exynos4210-origen.dts @@ -36,10 +36,10 @@ sdhci@12530000 { samsung,bus-width = <4>; samsung,timing = <1 2 3>; - cd-gpios = <&gpio 0x2008002 0>; + cd-gpios = <&gpio 0xA2 0>; }; sdhci@12540000 { status = "disabled"; }; -};
\ No newline at end of file +}; diff --git a/arch/arm/dts/exynos4210-trats.dts b/arch/arm/dts/exynos4210-trats.dts index 992e0234c9..0ff69393b7 100644 --- a/arch/arm/dts/exynos4210-trats.dts +++ b/arch/arm/dts/exynos4210-trats.dts @@ -101,7 +101,7 @@ sdhci@12510000 { samsung,bus-width = <8>; samsung,timing = <1 3 3>; - pwr-gpios = <&gpio 0x2008002 0>; + pwr-gpios = <&gpio 0xA2 0>; }; sdhci@12520000 { @@ -111,10 +111,10 @@ sdhci@12530000 { samsung,bus-width = <4>; samsung,timing = <1 2 3>; - cd-gpios = <&gpio 0x20c6004 0>; + cd-gpios = <&gpio 0x39C 0>; }; sdhci@12540000 { status = "disabled"; }; -};
\ No newline at end of file +}; diff --git a/arch/arm/dts/exynos4210-universal_c210.dts b/arch/arm/dts/exynos4210-universal_c210.dts index 1cdd981d6d..6941906aaa 100644 --- a/arch/arm/dts/exynos4210-universal_c210.dts +++ b/arch/arm/dts/exynos4210-universal_c210.dts @@ -24,7 +24,7 @@ sdhci@12510000 { samsung,bus-width = <8>; samsung,timing = <1 3 3>; - pwr-gpios = <&gpio 0x2008002 0>; + pwr-gpios = <&gpio 0xA2 0>; }; sdhci@12520000 { @@ -34,7 +34,7 @@ sdhci@12530000 { samsung,bus-width = <4>; samsung,timing = <1 2 3>; - cd-gpios = <&gpio 0x20c6004 0>; + cd-gpios = <&gpio 0x39C 0>; }; sdhci@12540000 { diff --git a/arch/arm/dts/exynos4412-trats2.dts b/arch/arm/dts/exynos4412-trats2.dts index 7d32067fdd..1596f8328a 100644 --- a/arch/arm/dts/exynos4412-trats2.dts +++ b/arch/arm/dts/exynos4412-trats2.dts @@ -415,7 +415,7 @@ sdhci@12510000 { samsung,bus-width = <8>; samsung,timing = <1 3 3>; - pwr-gpios = <&gpio 0x2004002 0>; + pwr-gpios = <&gpio 0xB2 0>; }; sdhci@12520000 { @@ -425,7 +425,7 @@ sdhci@12530000 { samsung,bus-width = <4>; samsung,timing = <1 2 3>; - cd-gpios = <&gpio 0x20C6004 0>; + cd-gpios = <&gpio 0x3BC 0>; }; sdhci@12540000 { diff --git a/arch/arm/dts/imx6q-sabreauto.dts b/arch/arm/dts/imx6q-sabreauto.dts index a3c9c91f32..7af2a88fd0 100644 --- a/arch/arm/dts/imx6q-sabreauto.dts +++ b/arch/arm/dts/imx6q-sabreauto.dts @@ -1,9 +1,9 @@ /* - + * Copyright 2012 Freescale Semiconductor, Inc. - + * Copyright 2011 Linaro Ltd. - + * - + * SPDX-License-Identifier: GPL-2.0+ - + */ + * Copyright 2012 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * SPDX-License-Identifier: GPL-2.0+ + */ /dts-v1/; diff --git a/arch/arm/imx-common/Makefile b/arch/arm/imx-common/Makefile index b04dfbbcb9..0e713952dc 100644 --- a/arch/arm/imx-common/Makefile +++ b/arch/arm/imx-common/Makefile @@ -19,6 +19,7 @@ obj-y += misc.o endif ifeq ($(SOC),$(filter $(SOC),mx6)) obj-$(CONFIG_CMD_SATA) += sata.o +obj-$(CONFIG_IMX_VIDEO_SKIP) += video.o endif obj-$(CONFIG_CMD_BMODE) += cmd_bmode.o obj-$(CONFIG_CMD_HDMIDETECT) += cmd_hdmidet.o diff --git a/arch/arm/imx-common/iomux-v3.c b/arch/arm/imx-common/iomux-v3.c index b59b802830..6e46ea8dcd 100644 --- a/arch/arm/imx-common/iomux-v3.c +++ b/arch/arm/imx-common/iomux-v3.c @@ -30,6 +30,14 @@ void imx_iomux_v3_setup_pad(iomux_v3_cfg_t pad) (pad & MUX_PAD_CTRL_OFS_MASK) >> MUX_PAD_CTRL_OFS_SHIFT; u32 pad_ctrl = (pad & MUX_PAD_CTRL_MASK) >> MUX_PAD_CTRL_SHIFT; +#if defined CONFIG_MX6SL + /* Check whether LVE bit needs to be set */ + if (pad_ctrl & PAD_CTL_LVE) { + pad_ctrl &= ~PAD_CTL_LVE; + pad_ctrl |= PAD_CTL_LVE_BIT; + } +#endif + if (mux_ctrl_ofs) __raw_writel(mux_mode, base + mux_ctrl_ofs); diff --git a/arch/arm/imx-common/video.c b/arch/arm/imx-common/video.c new file mode 100644 index 0000000000..0121cd78f2 --- /dev/null +++ b/arch/arm/imx-common/video.c @@ -0,0 +1,65 @@ +/* + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/errno.h> +#include <asm/imx-common/video.h> + +extern struct display_info_t const displays[]; +extern size_t display_count; + +int board_video_skip(void) +{ + int i; + int ret; + char const *panel = getenv("panel"); + if (!panel) { + for (i = 0; i < display_count; i++) { + struct display_info_t const *dev = displays+i; + if (dev->detect && dev->detect(dev)) { + panel = dev->mode.name; + printf("auto-detected panel %s\n", panel); + break; + } + } + if (!panel) { + panel = displays[0].mode.name; + printf("No panel detected: default to %s\n", panel); + i = 0; + } + } else { + for (i = 0; i < display_count; i++) { + if (!strcmp(panel, displays[i].mode.name)) + break; + } + } + if (i < display_count) { + ret = ipuv3_fb_init(&displays[i].mode, 0, + displays[i].pixfmt); + if (!ret) { + displays[i].enable(displays+i); + printf("Display: %s (%ux%u)\n", + displays[i].mode.name, + displays[i].mode.xres, + displays[i].mode.yres); + } else + printf("LCD %s cannot be configured: %d\n", + displays[i].mode.name, ret); + } else { + printf("unsupported panel %s\n", panel); + return -EINVAL; + } + + return 0; +} + +#ifdef CONFIG_IMX_HDMI +#include <asm/arch/mxc_hdmi.h> +#include <asm/io.h> +int detect_hdmi(struct display_info_t const *dev) +{ + struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; + return readb(&hdmi->phy_stat0) & HDMI_DVI_STAT; +} +#endif diff --git a/arch/arm/include/asm/arch-am33xx/clock.h b/arch/arm/include/asm/arch-am33xx/clock.h index 7637457549..f00fad38fe 100644 --- a/arch/arm/include/asm/arch-am33xx/clock.h +++ b/arch/arm/include/asm/arch-am33xx/clock.h @@ -42,6 +42,8 @@ #define MODULE_CLKCTRL_IDLEST_DISABLED 3 /* CM_CLKMODE_DPLL */ +#define CM_CLKMODE_DPLL_SSC_EN_SHIFT 12 +#define CM_CLKMODE_DPLL_SSC_EN_MASK (1 << 12) #define CM_CLKMODE_DPLL_REGM4XEN_SHIFT 11 #define CM_CLKMODE_DPLL_REGM4XEN_MASK (1 << 11) #define CM_CLKMODE_DPLL_LPMODE_EN_SHIFT 10 diff --git a/arch/arm/include/asm/arch-exynos/cpu.h b/arch/arm/include/asm/arch-exynos/cpu.h index fdf73b507a..ba717146f5 100644 --- a/arch/arm/include/asm/arch-exynos/cpu.h +++ b/arch/arm/include/asm/arch-exynos/cpu.h @@ -98,7 +98,7 @@ #define EXYNOS5_I2C_SPACING 0x10000 #define EXYNOS5_AUDIOSS_BASE 0x03810000 -#define EXYNOS5_GPIO_PART4_BASE 0x03860000 +#define EXYNOS5_GPIO_PART8_BASE 0x03860000 #define EXYNOS5_PRO_ID 0x10000000 #define EXYNOS5_CLOCK_BASE 0x10010000 #define EXYNOS5_POWER_BASE 0x10040000 @@ -108,9 +108,13 @@ #define EXYNOS5_WATCHDOG_BASE 0x101D0000 #define EXYNOS5_ACE_SFR_BASE 0x10830000 #define EXYNOS5_DMC_PHY_BASE 0x10C00000 -#define EXYNOS5_GPIO_PART3_BASE 0x10D10000 +#define EXYNOS5_GPIO_PART5_BASE 0x10D10000 +#define EXYNOS5_GPIO_PART6_BASE 0x10D10060 +#define EXYNOS5_GPIO_PART7_BASE 0x10D100C0 #define EXYNOS5_DMC_CTRL_BASE 0x10DD0000 #define EXYNOS5_GPIO_PART1_BASE 0x11400000 +#define EXYNOS5_GPIO_PART2_BASE 0x114002E0 +#define EXYNOS5_GPIO_PART3_BASE 0x11400C00 #define EXYNOS5_MIPI_DSIM_BASE 0x11D00000 #define EXYNOS5_USB_HOST_XHCI_BASE 0x12000000 #define EXYNOS5_USB3PHY_BASE 0x12100000 @@ -125,7 +129,7 @@ #define EXYNOS5_I2S_BASE 0x12D60000 #define EXYNOS5_PWMTIMER_BASE 0x12DD0000 #define EXYNOS5_SPI_ISP_BASE 0x131A0000 -#define EXYNOS5_GPIO_PART2_BASE 0x13400000 +#define EXYNOS5_GPIO_PART4_BASE 0x13400000 #define EXYNOS5_FIMD_BASE 0x14400000 #define EXYNOS5_DP_BASE 0x145B0000 @@ -135,7 +139,7 @@ /* EXYNOS5420 */ #define EXYNOS5420_AUDIOSS_BASE 0x03810000 -#define EXYNOS5420_GPIO_PART5_BASE 0x03860000 +#define EXYNOS5420_GPIO_PART6_BASE 0x03860000 #define EXYNOS5420_PRO_ID 0x10000000 #define EXYNOS5420_CLOCK_BASE 0x10010000 #define EXYNOS5420_POWER_BASE 0x10040000 @@ -158,8 +162,9 @@ #define EXYNOS5420_PWMTIMER_BASE 0x12DD0000 #define EXYNOS5420_SPI_ISP_BASE 0x131A0000 #define EXYNOS5420_GPIO_PART2_BASE 0x13400000 -#define EXYNOS5420_GPIO_PART3_BASE 0x13410000 -#define EXYNOS5420_GPIO_PART4_BASE 0x14000000 +#define EXYNOS5420_GPIO_PART3_BASE 0x13400C00 +#define EXYNOS5420_GPIO_PART4_BASE 0x13410000 +#define EXYNOS5420_GPIO_PART5_BASE 0x14000000 #define EXYNOS5420_GPIO_PART1_BASE 0x14010000 #define EXYNOS5420_MIPI_DSIM_BASE 0x14500000 #define EXYNOS5420_DP_BASE 0x145B0000 diff --git a/arch/arm/include/asm/arch-exynos/gpio.h b/arch/arm/include/asm/arch-exynos/gpio.h index d6868fa25d..be5113f0e2 100644 --- a/arch/arm/include/asm/arch-exynos/gpio.h +++ b/arch/arm/include/asm/arch-exynos/gpio.h @@ -19,328 +19,1515 @@ struct s5p_gpio_bank { unsigned char res1[8]; }; -struct exynos4_gpio_part1 { - struct s5p_gpio_bank a0; - struct s5p_gpio_bank a1; - struct s5p_gpio_bank b; - struct s5p_gpio_bank c0; - struct s5p_gpio_bank c1; - struct s5p_gpio_bank d0; - struct s5p_gpio_bank d1; - struct s5p_gpio_bank e0; - struct s5p_gpio_bank e1; - struct s5p_gpio_bank e2; - struct s5p_gpio_bank e3; - struct s5p_gpio_bank e4; - struct s5p_gpio_bank f0; - struct s5p_gpio_bank f1; - struct s5p_gpio_bank f2; - struct s5p_gpio_bank f3; -}; +/* GPIO pins per bank */ +#define GPIO_PER_BANK 8 -struct exynos4_gpio_part2 { - struct s5p_gpio_bank j0; - struct s5p_gpio_bank j1; - struct s5p_gpio_bank k0; - struct s5p_gpio_bank k1; - struct s5p_gpio_bank k2; - struct s5p_gpio_bank k3; - struct s5p_gpio_bank l0; - struct s5p_gpio_bank l1; - struct s5p_gpio_bank l2; - struct s5p_gpio_bank y0; - struct s5p_gpio_bank y1; - struct s5p_gpio_bank y2; - struct s5p_gpio_bank y3; - struct s5p_gpio_bank y4; - struct s5p_gpio_bank y5; - struct s5p_gpio_bank y6; - struct s5p_gpio_bank res1[80]; - struct s5p_gpio_bank x0; - struct s5p_gpio_bank x1; - struct s5p_gpio_bank x2; - struct s5p_gpio_bank x3; -}; +/* A list of valid GPIO numbers for the asm-generic/gpio.h interface */ +enum exynos4_gpio_pin { + /* GPIO_PART1_STARTS */ + EXYNOS4_GPIO_A00, /* 0 */ + EXYNOS4_GPIO_A01, + EXYNOS4_GPIO_A02, + EXYNOS4_GPIO_A03, + EXYNOS4_GPIO_A04, + EXYNOS4_GPIO_A05, + EXYNOS4_GPIO_A06, + EXYNOS4_GPIO_A07, + EXYNOS4_GPIO_A10, /* 8 */ + EXYNOS4_GPIO_A11, + EXYNOS4_GPIO_A12, + EXYNOS4_GPIO_A13, + EXYNOS4_GPIO_A14, + EXYNOS4_GPIO_A15, + EXYNOS4_GPIO_A16, + EXYNOS4_GPIO_A17, + EXYNOS4_GPIO_B0, /* 16 0x10 */ + EXYNOS4_GPIO_B1, + EXYNOS4_GPIO_B2, + EXYNOS4_GPIO_B3, + EXYNOS4_GPIO_B4, + EXYNOS4_GPIO_B5, + EXYNOS4_GPIO_B6, + EXYNOS4_GPIO_B7, + EXYNOS4_GPIO_C00, /* 24 0x18 */ + EXYNOS4_GPIO_C01, + EXYNOS4_GPIO_C02, + EXYNOS4_GPIO_C03, + EXYNOS4_GPIO_C04, + EXYNOS4_GPIO_C05, + EXYNOS4_GPIO_C06, + EXYNOS4_GPIO_C07, + EXYNOS4_GPIO_C10, /* 32 0x20*/ + EXYNOS4_GPIO_C11, + EXYNOS4_GPIO_C12, + EXYNOS4_GPIO_C13, + EXYNOS4_GPIO_C14, + EXYNOS4_GPIO_C15, + EXYNOS4_GPIO_C16, + EXYNOS4_GPIO_C17, + EXYNOS4_GPIO_D00, /* 40 0x28 */ + EXYNOS4_GPIO_D01, + EXYNOS4_GPIO_D02, + EXYNOS4_GPIO_D03, + EXYNOS4_GPIO_D04, + EXYNOS4_GPIO_D05, + EXYNOS4_GPIO_D06, + EXYNOS4_GPIO_D07, + EXYNOS4_GPIO_D10, /* 48 0x30 */ + EXYNOS4_GPIO_D11, + EXYNOS4_GPIO_D12, + EXYNOS4_GPIO_D13, + EXYNOS4_GPIO_D14, + EXYNOS4_GPIO_D15, + EXYNOS4_GPIO_D16, + EXYNOS4_GPIO_D17, + EXYNOS4_GPIO_E00, /* 56 0x38 */ + EXYNOS4_GPIO_E01, + EXYNOS4_GPIO_E02, + EXYNOS4_GPIO_E03, + EXYNOS4_GPIO_E04, + EXYNOS4_GPIO_E05, + EXYNOS4_GPIO_E06, + EXYNOS4_GPIO_E07, + EXYNOS4_GPIO_E10, /* 64 0x40 */ + EXYNOS4_GPIO_E11, + EXYNOS4_GPIO_E12, + EXYNOS4_GPIO_E13, + EXYNOS4_GPIO_E14, + EXYNOS4_GPIO_E15, + EXYNOS4_GPIO_E16, + EXYNOS4_GPIO_E17, + EXYNOS4_GPIO_E20, /* 72 0x48 */ + EXYNOS4_GPIO_E21, + EXYNOS4_GPIO_E22, + EXYNOS4_GPIO_E23, + EXYNOS4_GPIO_E24, + EXYNOS4_GPIO_E25, + EXYNOS4_GPIO_E26, + EXYNOS4_GPIO_E27, + EXYNOS4_GPIO_E30, /* 80 0x50 */ + EXYNOS4_GPIO_E31, + EXYNOS4_GPIO_E32, + EXYNOS4_GPIO_E33, + EXYNOS4_GPIO_E34, + EXYNOS4_GPIO_E35, + EXYNOS4_GPIO_E36, + EXYNOS4_GPIO_E37, + EXYNOS4_GPIO_E40, /* 88 0x58 */ + EXYNOS4_GPIO_E41, + EXYNOS4_GPIO_E42, + EXYNOS4_GPIO_E43, + EXYNOS4_GPIO_E44, + EXYNOS4_GPIO_E45, + EXYNOS4_GPIO_E46, + EXYNOS4_GPIO_E47, + EXYNOS4_GPIO_F00, /* 96 0x60 */ + EXYNOS4_GPIO_F01, + EXYNOS4_GPIO_F02, + EXYNOS4_GPIO_F03, + EXYNOS4_GPIO_F04, + EXYNOS4_GPIO_F05, + EXYNOS4_GPIO_F06, + EXYNOS4_GPIO_F07, + EXYNOS4_GPIO_F10, /* 104 0x68 */ + EXYNOS4_GPIO_F11, + EXYNOS4_GPIO_F12, + EXYNOS4_GPIO_F13, + EXYNOS4_GPIO_F14, + EXYNOS4_GPIO_F15, + EXYNOS4_GPIO_F16, + EXYNOS4_GPIO_F17, + EXYNOS4_GPIO_F20, /* 112 0x70 */ + EXYNOS4_GPIO_F21, + EXYNOS4_GPIO_F22, + EXYNOS4_GPIO_F23, + EXYNOS4_GPIO_F24, + EXYNOS4_GPIO_F25, + EXYNOS4_GPIO_F26, + EXYNOS4_GPIO_F27, + EXYNOS4_GPIO_F30, /* 120 0x78 */ + EXYNOS4_GPIO_F31, + EXYNOS4_GPIO_F32, + EXYNOS4_GPIO_F33, + EXYNOS4_GPIO_F34, + EXYNOS4_GPIO_F35, + EXYNOS4_GPIO_F36, + EXYNOS4_GPIO_F37, -struct exynos4_gpio_part3 { - struct s5p_gpio_bank z; -}; + /* GPIO_PART2_STARTS */ + EXYNOS4_GPIO_MAX_PORT_PART_1, /* 128 0x80 */ + EXYNOS4_GPIO_J00 = EXYNOS4_GPIO_MAX_PORT_PART_1, + EXYNOS4_GPIO_J01, + EXYNOS4_GPIO_J02, + EXYNOS4_GPIO_J03, + EXYNOS4_GPIO_J04, + EXYNOS4_GPIO_J05, + EXYNOS4_GPIO_J06, + EXYNOS4_GPIO_J07, + EXYNOS4_GPIO_J10, /* 136 0x88 */ + EXYNOS4_GPIO_J11, + EXYNOS4_GPIO_J12, + EXYNOS4_GPIO_J13, + EXYNOS4_GPIO_J14, + EXYNOS4_GPIO_J15, + EXYNOS4_GPIO_J16, + EXYNOS4_GPIO_J17, + EXYNOS4_GPIO_K00, /* 144 0x90 */ + EXYNOS4_GPIO_K01, + EXYNOS4_GPIO_K02, + EXYNOS4_GPIO_K03, + EXYNOS4_GPIO_K04, + EXYNOS4_GPIO_K05, + EXYNOS4_GPIO_K06, + EXYNOS4_GPIO_K07, + EXYNOS4_GPIO_K10, /* 152 0x98 */ + EXYNOS4_GPIO_K11, + EXYNOS4_GPIO_K12, + EXYNOS4_GPIO_K13, + EXYNOS4_GPIO_K14, + EXYNOS4_GPIO_K15, + EXYNOS4_GPIO_K16, + EXYNOS4_GPIO_K17, + EXYNOS4_GPIO_K20, /* 160 0xA0 */ + EXYNOS4_GPIO_K21, + EXYNOS4_GPIO_K22, + EXYNOS4_GPIO_K23, + EXYNOS4_GPIO_K24, + EXYNOS4_GPIO_K25, + EXYNOS4_GPIO_K26, + EXYNOS4_GPIO_K27, + EXYNOS4_GPIO_K30, /* 168 0xA8 */ + EXYNOS4_GPIO_K31, + EXYNOS4_GPIO_K32, + EXYNOS4_GPIO_K33, + EXYNOS4_GPIO_K34, + EXYNOS4_GPIO_K35, + EXYNOS4_GPIO_K36, + EXYNOS4_GPIO_K37, + EXYNOS4_GPIO_L00, /* 176 0xB0 */ + EXYNOS4_GPIO_L01, + EXYNOS4_GPIO_L02, + EXYNOS4_GPIO_L03, + EXYNOS4_GPIO_L04, + EXYNOS4_GPIO_L05, + EXYNOS4_GPIO_L06, + EXYNOS4_GPIO_L07, + EXYNOS4_GPIO_L10, /* 184 0xB8 */ + EXYNOS4_GPIO_L11, + EXYNOS4_GPIO_L12, + EXYNOS4_GPIO_L13, + EXYNOS4_GPIO_L14, + EXYNOS4_GPIO_L15, + EXYNOS4_GPIO_L16, + EXYNOS4_GPIO_L17, + EXYNOS4_GPIO_L20, /* 192 0xC0 */ + EXYNOS4_GPIO_L21, + EXYNOS4_GPIO_L22, + EXYNOS4_GPIO_L23, + EXYNOS4_GPIO_L24, + EXYNOS4_GPIO_L25, + EXYNOS4_GPIO_L26, + EXYNOS4_GPIO_L27, + EXYNOS4_GPIO_Y00, /* 200 0xC8 */ + EXYNOS4_GPIO_Y01, + EXYNOS4_GPIO_Y02, + EXYNOS4_GPIO_Y03, + EXYNOS4_GPIO_Y04, + EXYNOS4_GPIO_Y05, + EXYNOS4_GPIO_Y06, + EXYNOS4_GPIO_Y07, + EXYNOS4_GPIO_Y10, /* 208 0xD0 */ + EXYNOS4_GPIO_Y11, + EXYNOS4_GPIO_Y12, + EXYNOS4_GPIO_Y13, + EXYNOS4_GPIO_Y14, + EXYNOS4_GPIO_Y15, + EXYNOS4_GPIO_Y16, + EXYNOS4_GPIO_Y17, + EXYNOS4_GPIO_Y20, /* 216 0xD8 */ + EXYNOS4_GPIO_Y21, + EXYNOS4_GPIO_Y22, + EXYNOS4_GPIO_Y23, + EXYNOS4_GPIO_Y24, + EXYNOS4_GPIO_Y25, + EXYNOS4_GPIO_Y26, + EXYNOS4_GPIO_Y27, + EXYNOS4_GPIO_Y30, /* 224 0xE0 */ + EXYNOS4_GPIO_Y31, + EXYNOS4_GPIO_Y32, + EXYNOS4_GPIO_Y33, + EXYNOS4_GPIO_Y34, + EXYNOS4_GPIO_Y35, + EXYNOS4_GPIO_Y36, + EXYNOS4_GPIO_Y37, + EXYNOS4_GPIO_Y40, /* 232 0xE8 */ + EXYNOS4_GPIO_Y41, + EXYNOS4_GPIO_Y42, + EXYNOS4_GPIO_Y43, + EXYNOS4_GPIO_Y44, + EXYNOS4_GPIO_Y45, + EXYNOS4_GPIO_Y46, + EXYNOS4_GPIO_Y47, + EXYNOS4_GPIO_Y50, /* 240 0xF0 */ + EXYNOS4_GPIO_Y51, + EXYNOS4_GPIO_Y52, + EXYNOS4_GPIO_Y53, + EXYNOS4_GPIO_Y54, + EXYNOS4_GPIO_Y55, + EXYNOS4_GPIO_Y56, + EXYNOS4_GPIO_Y57, + EXYNOS4_GPIO_Y60, /* 248 0xF8 */ + EXYNOS4_GPIO_Y61, + EXYNOS4_GPIO_Y62, + EXYNOS4_GPIO_Y63, + EXYNOS4_GPIO_Y64, + EXYNOS4_GPIO_Y65, + EXYNOS4_GPIO_Y66, + EXYNOS4_GPIO_Y67, + EXYNOS4_GPIO_X00 = 896, /* 896 0x380 */ + EXYNOS4_GPIO_X01, + EXYNOS4_GPIO_X02, + EXYNOS4_GPIO_X03, + EXYNOS4_GPIO_X04, + EXYNOS4_GPIO_X05, + EXYNOS4_GPIO_X06, + EXYNOS4_GPIO_X07, + EXYNOS4_GPIO_X10, /* 904 0x388 */ + EXYNOS4_GPIO_X11, + EXYNOS4_GPIO_X12, + EXYNOS4_GPIO_X13, + EXYNOS4_GPIO_X14, + EXYNOS4_GPIO_X15, + EXYNOS4_GPIO_X16, + EXYNOS4_GPIO_X17, + EXYNOS4_GPIO_X20, /* 912 0x390 */ + EXYNOS4_GPIO_X21, + EXYNOS4_GPIO_X22, + EXYNOS4_GPIO_X23, + EXYNOS4_GPIO_X24, + EXYNOS4_GPIO_X25, + EXYNOS4_GPIO_X26, + EXYNOS4_GPIO_X27, + EXYNOS4_GPIO_X30, /* 920 0x398 */ + EXYNOS4_GPIO_X31, + EXYNOS4_GPIO_X32, + EXYNOS4_GPIO_X33, + EXYNOS4_GPIO_X34, + EXYNOS4_GPIO_X35, + EXYNOS4_GPIO_X36, + EXYNOS4_GPIO_X37, + + /* GPIO_PART3_STARTS */ + EXYNOS4_GPIO_MAX_PORT_PART_2, /* 928 0x3A0 */ + EXYNOS4_GPIO_Z0 = EXYNOS4_GPIO_MAX_PORT_PART_2, + EXYNOS4_GPIO_Z1, + EXYNOS4_GPIO_Z2, + EXYNOS4_GPIO_Z3, + EXYNOS4_GPIO_Z4, + EXYNOS4_GPIO_Z5, + EXYNOS4_GPIO_Z6, + EXYNOS4_GPIO_Z7, -struct exynos4x12_gpio_part1 { - struct s5p_gpio_bank a0; - struct s5p_gpio_bank a1; - struct s5p_gpio_bank b; - struct s5p_gpio_bank c0; - struct s5p_gpio_bank c1; - struct s5p_gpio_bank d0; - struct s5p_gpio_bank d1; - struct s5p_gpio_bank res1[0x5]; - struct s5p_gpio_bank f0; - struct s5p_gpio_bank f1; - struct s5p_gpio_bank f2; - struct s5p_gpio_bank f3; - struct s5p_gpio_bank res2[0x2]; - struct s5p_gpio_bank j0; - struct s5p_gpio_bank j1; + EXYNOS4_GPIO_MAX_PORT }; -struct exynos4x12_gpio_part2 { - struct s5p_gpio_bank res1[0x2]; - struct s5p_gpio_bank k0; - struct s5p_gpio_bank k1; - struct s5p_gpio_bank k2; - struct s5p_gpio_bank k3; - struct s5p_gpio_bank l0; - struct s5p_gpio_bank l1; - struct s5p_gpio_bank l2; - struct s5p_gpio_bank y0; - struct s5p_gpio_bank y1; - struct s5p_gpio_bank y2; - struct s5p_gpio_bank y3; - struct s5p_gpio_bank y4; - struct s5p_gpio_bank y5; - struct s5p_gpio_bank y6; - struct s5p_gpio_bank res2[0x3]; - struct s5p_gpio_bank m0; - struct s5p_gpio_bank m1; - struct s5p_gpio_bank m2; - struct s5p_gpio_bank m3; - struct s5p_gpio_bank m4; - struct s5p_gpio_bank res3[0x48]; - struct s5p_gpio_bank x0; - struct s5p_gpio_bank x1; - struct s5p_gpio_bank x2; - struct s5p_gpio_bank x3; +enum exynos4X12_gpio_pin { + /* GPIO_PART1_STARTS */ + EXYNOS4X12_GPIO_A00, /* 0 */ + EXYNOS4X12_GPIO_A01, + EXYNOS4X12_GPIO_A02, + EXYNOS4X12_GPIO_A03, + EXYNOS4X12_GPIO_A04, + EXYNOS4X12_GPIO_A05, + EXYNOS4X12_GPIO_A06, + EXYNOS4X12_GPIO_A07, + EXYNOS4X12_GPIO_A10, /* 8 */ + EXYNOS4X12_GPIO_A11, + EXYNOS4X12_GPIO_A12, + EXYNOS4X12_GPIO_A13, + EXYNOS4X12_GPIO_A14, + EXYNOS4X12_GPIO_A15, + EXYNOS4X12_GPIO_A16, + EXYNOS4X12_GPIO_A17, + EXYNOS4X12_GPIO_B0, /* 16 0x10 */ + EXYNOS4X12_GPIO_B1, + EXYNOS4X12_GPIO_B2, + EXYNOS4X12_GPIO_B3, + EXYNOS4X12_GPIO_B4, + EXYNOS4X12_GPIO_B5, + EXYNOS4X12_GPIO_B6, + EXYNOS4X12_GPIO_B7, + EXYNOS4X12_GPIO_C00, /* 24 0x18 */ + EXYNOS4X12_GPIO_C01, + EXYNOS4X12_GPIO_C02, + EXYNOS4X12_GPIO_C03, + EXYNOS4X12_GPIO_C04, + EXYNOS4X12_GPIO_C05, + EXYNOS4X12_GPIO_C06, + EXYNOS4X12_GPIO_C07, + EXYNOS4X12_GPIO_C10, /* 32 0x20 */ + EXYNOS4X12_GPIO_C11, + EXYNOS4X12_GPIO_C12, + EXYNOS4X12_GPIO_C13, + EXYNOS4X12_GPIO_C14, + EXYNOS4X12_GPIO_C15, + EXYNOS4X12_GPIO_C16, + EXYNOS4X12_GPIO_C17, + EXYNOS4X12_GPIO_D00, /* 40 0x28 */ + EXYNOS4X12_GPIO_D01, + EXYNOS4X12_GPIO_D02, + EXYNOS4X12_GPIO_D03, + EXYNOS4X12_GPIO_D04, + EXYNOS4X12_GPIO_D05, + EXYNOS4X12_GPIO_D06, + EXYNOS4X12_GPIO_D07, + EXYNOS4X12_GPIO_D10, /* 48 0x30 */ + EXYNOS4X12_GPIO_D11, + EXYNOS4X12_GPIO_D12, + EXYNOS4X12_GPIO_D13, + EXYNOS4X12_GPIO_D14, + EXYNOS4X12_GPIO_D15, + EXYNOS4X12_GPIO_D16, + EXYNOS4X12_GPIO_D17, + EXYNOS4X12_GPIO_F00 = 96, /* 96 0x60 */ + EXYNOS4X12_GPIO_F01, + EXYNOS4X12_GPIO_F02, + EXYNOS4X12_GPIO_F03, + EXYNOS4X12_GPIO_F04, + EXYNOS4X12_GPIO_F05, + EXYNOS4X12_GPIO_F06, + EXYNOS4X12_GPIO_F07, + EXYNOS4X12_GPIO_F10, /* 104 0x68 */ + EXYNOS4X12_GPIO_F11, + EXYNOS4X12_GPIO_F12, + EXYNOS4X12_GPIO_F13, + EXYNOS4X12_GPIO_F14, + EXYNOS4X12_GPIO_F15, + EXYNOS4X12_GPIO_F16, + EXYNOS4X12_GPIO_F17, + EXYNOS4X12_GPIO_F20, /* 112 0x70 */ + EXYNOS4X12_GPIO_F21, + EXYNOS4X12_GPIO_F22, + EXYNOS4X12_GPIO_F23, + EXYNOS4X12_GPIO_F24, + EXYNOS4X12_GPIO_F25, + EXYNOS4X12_GPIO_F26, + EXYNOS4X12_GPIO_F27, + EXYNOS4X12_GPIO_F30, /* 120 0x78 */ + EXYNOS4X12_GPIO_F31, + EXYNOS4X12_GPIO_F32, + EXYNOS4X12_GPIO_F33, + EXYNOS4X12_GPIO_F34, + EXYNOS4X12_GPIO_F35, + EXYNOS4X12_GPIO_F36, + EXYNOS4X12_GPIO_F37, + EXYNOS4X12_GPIO_J00 = 144, /* 144 0x90 */ + EXYNOS4X12_GPIO_J01, + EXYNOS4X12_GPIO_J02, + EXYNOS4X12_GPIO_J03, + EXYNOS4X12_GPIO_J04, + EXYNOS4X12_GPIO_J05, + EXYNOS4X12_GPIO_J06, + EXYNOS4X12_GPIO_J07, + EXYNOS4X12_GPIO_J10, /* 152 0x98 */ + EXYNOS4X12_GPIO_J11, + EXYNOS4X12_GPIO_J12, + EXYNOS4X12_GPIO_J13, + EXYNOS4X12_GPIO_J14, + EXYNOS4X12_GPIO_J15, + EXYNOS4X12_GPIO_J16, + EXYNOS4X12_GPIO_J17, + + /* GPIO_PART2_STARTS */ + EXYNOS4X12_GPIO_MAX_PORT_PART_1,/* 160 0xA0 */ + EXYNOS4X12_GPIO_K00 = 176, /* 176 0xB0 */ + EXYNOS4X12_GPIO_K01, + EXYNOS4X12_GPIO_K02, + EXYNOS4X12_GPIO_K03, + EXYNOS4X12_GPIO_K04, + EXYNOS4X12_GPIO_K05, + EXYNOS4X12_GPIO_K06, + EXYNOS4X12_GPIO_K07, + EXYNOS4X12_GPIO_K10, /* 184 0xB8 */ + EXYNOS4X12_GPIO_K11, + EXYNOS4X12_GPIO_K12, + EXYNOS4X12_GPIO_K13, + EXYNOS4X12_GPIO_K14, + EXYNOS4X12_GPIO_K15, + EXYNOS4X12_GPIO_K16, + EXYNOS4X12_GPIO_K17, + EXYNOS4X12_GPIO_K20, /* 192 0xC0 */ + EXYNOS4X12_GPIO_K21, + EXYNOS4X12_GPIO_K22, + EXYNOS4X12_GPIO_K23, + EXYNOS4X12_GPIO_K24, + EXYNOS4X12_GPIO_K25, + EXYNOS4X12_GPIO_K26, + EXYNOS4X12_GPIO_K27, + EXYNOS4X12_GPIO_K30, /* 200 0xC8 */ + EXYNOS4X12_GPIO_K31, + EXYNOS4X12_GPIO_K32, + EXYNOS4X12_GPIO_K33, + EXYNOS4X12_GPIO_K34, + EXYNOS4X12_GPIO_K35, + EXYNOS4X12_GPIO_K36, + EXYNOS4X12_GPIO_K37, + EXYNOS4X12_GPIO_L00, /* 208 0xD0 */ + EXYNOS4X12_GPIO_L01, + EXYNOS4X12_GPIO_L02, + EXYNOS4X12_GPIO_L03, + EXYNOS4X12_GPIO_L04, + EXYNOS4X12_GPIO_L05, + EXYNOS4X12_GPIO_L06, + EXYNOS4X12_GPIO_L07, + EXYNOS4X12_GPIO_L10, /* 216 0xD8 */ + EXYNOS4X12_GPIO_L11, + EXYNOS4X12_GPIO_L12, + EXYNOS4X12_GPIO_L13, + EXYNOS4X12_GPIO_L14, + EXYNOS4X12_GPIO_L15, + EXYNOS4X12_GPIO_L16, + EXYNOS4X12_GPIO_L17, + EXYNOS4X12_GPIO_L20, /* 224 0xE0 */ + EXYNOS4X12_GPIO_L21, + EXYNOS4X12_GPIO_L22, + EXYNOS4X12_GPIO_L23, + EXYNOS4X12_GPIO_L24, + EXYNOS4X12_GPIO_L25, + EXYNOS4X12_GPIO_L26, + EXYNOS4X12_GPIO_L27, + EXYNOS4X12_GPIO_Y00, /* 232 0xE8 */ + EXYNOS4X12_GPIO_Y01, + EXYNOS4X12_GPIO_Y02, + EXYNOS4X12_GPIO_Y03, + EXYNOS4X12_GPIO_Y04, + EXYNOS4X12_GPIO_Y05, + EXYNOS4X12_GPIO_Y06, + EXYNOS4X12_GPIO_Y07, + EXYNOS4X12_GPIO_Y10, /* 240 0xF0 */ + EXYNOS4X12_GPIO_Y11, + EXYNOS4X12_GPIO_Y12, + EXYNOS4X12_GPIO_Y13, + EXYNOS4X12_GPIO_Y14, + EXYNOS4X12_GPIO_Y15, + EXYNOS4X12_GPIO_Y16, + EXYNOS4X12_GPIO_Y17, + EXYNOS4X12_GPIO_Y20, /* 248 0xF8 */ + EXYNOS4X12_GPIO_Y21, + EXYNOS4X12_GPIO_Y22, + EXYNOS4X12_GPIO_Y23, + EXYNOS4X12_GPIO_Y24, + EXYNOS4X12_GPIO_Y25, + EXYNOS4X12_GPIO_Y26, + EXYNOS4X12_GPIO_Y27, + EXYNOS4X12_GPIO_Y30, /* 256 0x100 */ + EXYNOS4X12_GPIO_Y31, + EXYNOS4X12_GPIO_Y32, + EXYNOS4X12_GPIO_Y33, + EXYNOS4X12_GPIO_Y34, + EXYNOS4X12_GPIO_Y35, + EXYNOS4X12_GPIO_Y36, + EXYNOS4X12_GPIO_Y37, + EXYNOS4X12_GPIO_Y40, /* 264 0x108 */ + EXYNOS4X12_GPIO_Y41, + EXYNOS4X12_GPIO_Y42, + EXYNOS4X12_GPIO_Y43, + EXYNOS4X12_GPIO_Y44, + EXYNOS4X12_GPIO_Y45, + EXYNOS4X12_GPIO_Y46, + EXYNOS4X12_GPIO_Y47, + EXYNOS4X12_GPIO_Y50, /* 272 0x110 */ + EXYNOS4X12_GPIO_Y51, + EXYNOS4X12_GPIO_Y52, + EXYNOS4X12_GPIO_Y53, + EXYNOS4X12_GPIO_Y54, + EXYNOS4X12_GPIO_Y55, + EXYNOS4X12_GPIO_Y56, + EXYNOS4X12_GPIO_Y57, + EXYNOS4X12_GPIO_Y60, /* 280 0x118 */ + EXYNOS4X12_GPIO_Y61, + EXYNOS4X12_GPIO_Y62, + EXYNOS4X12_GPIO_Y63, + EXYNOS4X12_GPIO_Y64, + EXYNOS4X12_GPIO_Y65, + EXYNOS4X12_GPIO_Y66, + EXYNOS4X12_GPIO_Y67, + EXYNOS4X12_GPIO_M00 = 312, /* 312 0xF0 */ + EXYNOS4X12_GPIO_M01, + EXYNOS4X12_GPIO_M02, + EXYNOS4X12_GPIO_M03, + EXYNOS4X12_GPIO_M04, + EXYNOS4X12_GPIO_M05, + EXYNOS4X12_GPIO_M06, + EXYNOS4X12_GPIO_M07, + EXYNOS4X12_GPIO_M10, /* 320 0xF8 */ + EXYNOS4X12_GPIO_M11, + EXYNOS4X12_GPIO_M12, + EXYNOS4X12_GPIO_M13, + EXYNOS4X12_GPIO_M14, + EXYNOS4X12_GPIO_M15, + EXYNOS4X12_GPIO_M16, + EXYNOS4X12_GPIO_M17, + EXYNOS4X12_GPIO_M20, /* 328 0x100 */ + EXYNOS4X12_GPIO_M21, + EXYNOS4X12_GPIO_M22, + EXYNOS4X12_GPIO_M23, + EXYNOS4X12_GPIO_M24, + EXYNOS4X12_GPIO_M25, + EXYNOS4X12_GPIO_M26, + EXYNOS4X12_GPIO_M27, + EXYNOS4X12_GPIO_M30, /* 336 0x108 */ + EXYNOS4X12_GPIO_M31, + EXYNOS4X12_GPIO_M32, + EXYNOS4X12_GPIO_M33, + EXYNOS4X12_GPIO_M34, + EXYNOS4X12_GPIO_M35, + EXYNOS4X12_GPIO_M36, + EXYNOS4X12_GPIO_M37, + EXYNOS4X12_GPIO_M40, /* 344 0x110 */ + EXYNOS4X12_GPIO_M41, + EXYNOS4X12_GPIO_M42, + EXYNOS4X12_GPIO_M43, + EXYNOS4X12_GPIO_M44, + EXYNOS4X12_GPIO_M45, + EXYNOS4X12_GPIO_M46, + EXYNOS4X12_GPIO_M47, + EXYNOS4X12_GPIO_X00 = 928, /* 928 0x3A0 */ + EXYNOS4X12_GPIO_X01, + EXYNOS4X12_GPIO_X02, + EXYNOS4X12_GPIO_X03, + EXYNOS4X12_GPIO_X04, + EXYNOS4X12_GPIO_X05, + EXYNOS4X12_GPIO_X06, + EXYNOS4X12_GPIO_X07, + EXYNOS4X12_GPIO_X10, /* 936 0x3A8 */ + EXYNOS4X12_GPIO_X11, + EXYNOS4X12_GPIO_X12, + EXYNOS4X12_GPIO_X13, + EXYNOS4X12_GPIO_X14, + EXYNOS4X12_GPIO_X15, + EXYNOS4X12_GPIO_X16, + EXYNOS4X12_GPIO_X17, + EXYNOS4X12_GPIO_X20, /* 944 0x3B0 */ + EXYNOS4X12_GPIO_X21, + EXYNOS4X12_GPIO_X22, + EXYNOS4X12_GPIO_X23, + EXYNOS4X12_GPIO_X24, + EXYNOS4X12_GPIO_X25, + EXYNOS4X12_GPIO_X26, + EXYNOS4X12_GPIO_X27, + EXYNOS4X12_GPIO_X30, /* 952 0x3B8 */ + EXYNOS4X12_GPIO_X31, + EXYNOS4X12_GPIO_X32, + EXYNOS4X12_GPIO_X33, + EXYNOS4X12_GPIO_X34, + EXYNOS4X12_GPIO_X35, + EXYNOS4X12_GPIO_X36, + EXYNOS4X12_GPIO_X37, + + /* GPIO_PART3_STARTS */ + EXYNOS4X12_GPIO_MAX_PORT_PART_2,/* 960 0x3C0 */ + EXYNOS4X12_GPIO_Z0 = EXYNOS4X12_GPIO_MAX_PORT_PART_2, + EXYNOS4X12_GPIO_Z1, + EXYNOS4X12_GPIO_Z2, + EXYNOS4X12_GPIO_Z3, + EXYNOS4X12_GPIO_Z4, + EXYNOS4X12_GPIO_Z5, + EXYNOS4X12_GPIO_Z6, + EXYNOS4X12_GPIO_Z7, + + /* GPIO_PART4_STARTS */ + EXYNOS4X12_GPIO_MAX_PORT_PART_3,/* 968 0x3C8 */ + EXYNOS4X12_GPIO_V00 = EXYNOS4X12_GPIO_MAX_PORT_PART_3, + EXYNOS4X12_GPIO_V01, + EXYNOS4X12_GPIO_V02, + EXYNOS4X12_GPIO_V03, + EXYNOS4X12_GPIO_V04, + EXYNOS4X12_GPIO_V05, + EXYNOS4X12_GPIO_V06, + EXYNOS4X12_GPIO_V07, + EXYNOS4X12_GPIO_V10, /* 976 0x3D0 */ + EXYNOS4X12_GPIO_V11, + EXYNOS4X12_GPIO_V12, + EXYNOS4X12_GPIO_V13, + EXYNOS4X12_GPIO_V14, + EXYNOS4X12_GPIO_V15, + EXYNOS4X12_GPIO_V16, + EXYNOS4X12_GPIO_V17, + EXYNOS4X12_GPIO_V20 = 992, /* 992 0x3E0 */ + EXYNOS4X12_GPIO_V21, + EXYNOS4X12_GPIO_V22, + EXYNOS4X12_GPIO_V23, + EXYNOS4X12_GPIO_V24, + EXYNOS4X12_GPIO_V25, + EXYNOS4X12_GPIO_V26, + EXYNOS4X12_GPIO_V27, + EXYNOS4X12_GPIO_V30 = 1000, /* 1000 0x3E8 */ + EXYNOS4X12_GPIO_V31, + EXYNOS4X12_GPIO_V32, + EXYNOS4X12_GPIO_V33, + EXYNOS4X12_GPIO_V34, + EXYNOS4X12_GPIO_V35, + EXYNOS4X12_GPIO_V36, + EXYNOS4X12_GPIO_V37, + EXYNOS4X12_GPIO_V40 = 1016, /* 1016 0x3F8 */ + EXYNOS4X12_GPIO_V41, + EXYNOS4X12_GPIO_V42, + EXYNOS4X12_GPIO_V43, + EXYNOS4X12_GPIO_V44, + EXYNOS4X12_GPIO_V45, + EXYNOS4X12_GPIO_V46, + EXYNOS4X12_GPIO_V47, + + EXYNOS4X12_GPIO_MAX_PORT }; -struct exynos4x12_gpio_part3 { - struct s5p_gpio_bank z; +enum exynos5_gpio_pin { + /* GPIO_PART1_STARTS */ + EXYNOS5_GPIO_A00, /* 0 */ + EXYNOS5_GPIO_A01, + EXYNOS5_GPIO_A02, + EXYNOS5_GPIO_A03, + EXYNOS5_GPIO_A04, + EXYNOS5_GPIO_A05, + EXYNOS5_GPIO_A06, + EXYNOS5_GPIO_A07, + EXYNOS5_GPIO_A10, /* 8 */ + EXYNOS5_GPIO_A11, + EXYNOS5_GPIO_A12, + EXYNOS5_GPIO_A13, + EXYNOS5_GPIO_A14, + EXYNOS5_GPIO_A15, + EXYNOS5_GPIO_A16, + EXYNOS5_GPIO_A17, + EXYNOS5_GPIO_A20, /* 16 0x10 */ + EXYNOS5_GPIO_A21, + EXYNOS5_GPIO_A22, + EXYNOS5_GPIO_A23, + EXYNOS5_GPIO_A24, + EXYNOS5_GPIO_A25, + EXYNOS5_GPIO_A26, + EXYNOS5_GPIO_A27, + EXYNOS5_GPIO_B00, /* 24 0x18 */ + EXYNOS5_GPIO_B01, + EXYNOS5_GPIO_B02, + EXYNOS5_GPIO_B03, + EXYNOS5_GPIO_B04, + EXYNOS5_GPIO_B05, + EXYNOS5_GPIO_B06, + EXYNOS5_GPIO_B07, + EXYNOS5_GPIO_B10, /* 32 0x20 */ + EXYNOS5_GPIO_B11, + EXYNOS5_GPIO_B12, + EXYNOS5_GPIO_B13, + EXYNOS5_GPIO_B14, + EXYNOS5_GPIO_B15, + EXYNOS5_GPIO_B16, + EXYNOS5_GPIO_B17, + EXYNOS5_GPIO_B20, /* 40 0x28 */ + EXYNOS5_GPIO_B21, + EXYNOS5_GPIO_B22, + EXYNOS5_GPIO_B23, + EXYNOS5_GPIO_B24, + EXYNOS5_GPIO_B25, + EXYNOS5_GPIO_B26, + EXYNOS5_GPIO_B27, + EXYNOS5_GPIO_B30, /* 48 0x39 */ + EXYNOS5_GPIO_B31, + EXYNOS5_GPIO_B32, + EXYNOS5_GPIO_B33, + EXYNOS5_GPIO_B34, + EXYNOS5_GPIO_B35, + EXYNOS5_GPIO_B36, + EXYNOS5_GPIO_B37, + EXYNOS5_GPIO_C00, /* 56 0x38 */ + EXYNOS5_GPIO_C01, + EXYNOS5_GPIO_C02, + EXYNOS5_GPIO_C03, + EXYNOS5_GPIO_C04, + EXYNOS5_GPIO_C05, + EXYNOS5_GPIO_C06, + EXYNOS5_GPIO_C07, + EXYNOS5_GPIO_C10, /* 64 0x40 */ + EXYNOS5_GPIO_C11, + EXYNOS5_GPIO_C12, + EXYNOS5_GPIO_C13, + EXYNOS5_GPIO_C14, + EXYNOS5_GPIO_C15, + EXYNOS5_GPIO_C16, + EXYNOS5_GPIO_C17, + EXYNOS5_GPIO_C20, /* 72 0x48 */ + EXYNOS5_GPIO_C21, + EXYNOS5_GPIO_C22, + EXYNOS5_GPIO_C23, + EXYNOS5_GPIO_C24, + EXYNOS5_GPIO_C25, + EXYNOS5_GPIO_C26, + EXYNOS5_GPIO_C27, + EXYNOS5_GPIO_C30, /* 80 0x50 */ + EXYNOS5_GPIO_C31, + EXYNOS5_GPIO_C32, + EXYNOS5_GPIO_C33, + EXYNOS5_GPIO_C34, + EXYNOS5_GPIO_C35, + EXYNOS5_GPIO_C36, + EXYNOS5_GPIO_C37, + EXYNOS5_GPIO_D00, /* 88 0x58 */ + EXYNOS5_GPIO_D01, + EXYNOS5_GPIO_D02, + EXYNOS5_GPIO_D03, + EXYNOS5_GPIO_D04, + EXYNOS5_GPIO_D05, + EXYNOS5_GPIO_D06, + EXYNOS5_GPIO_D07, + EXYNOS5_GPIO_D10, /* 96 0x60 */ + EXYNOS5_GPIO_D11, + EXYNOS5_GPIO_D12, + EXYNOS5_GPIO_D13, + EXYNOS5_GPIO_D14, + EXYNOS5_GPIO_D15, + EXYNOS5_GPIO_D16, + EXYNOS5_GPIO_D17, + EXYNOS5_GPIO_Y00, /* 104 0x68 */ + EXYNOS5_GPIO_Y01, + EXYNOS5_GPIO_Y02, + EXYNOS5_GPIO_Y03, + EXYNOS5_GPIO_Y04, + EXYNOS5_GPIO_Y05, + EXYNOS5_GPIO_Y06, + EXYNOS5_GPIO_Y07, + EXYNOS5_GPIO_Y10, /* 112 0x70 */ + EXYNOS5_GPIO_Y11, + EXYNOS5_GPIO_Y12, + EXYNOS5_GPIO_Y13, + EXYNOS5_GPIO_Y14, + EXYNOS5_GPIO_Y15, + EXYNOS5_GPIO_Y16, + EXYNOS5_GPIO_Y17, + EXYNOS5_GPIO_Y20, /* 120 0x78 */ + EXYNOS5_GPIO_Y21, + EXYNOS5_GPIO_Y22, + EXYNOS5_GPIO_Y23, + EXYNOS5_GPIO_Y24, + EXYNOS5_GPIO_Y25, + EXYNOS5_GPIO_Y26, + EXYNOS5_GPIO_Y27, + EXYNOS5_GPIO_Y30, /* 128 0x80 */ + EXYNOS5_GPIO_Y31, + EXYNOS5_GPIO_Y32, + EXYNOS5_GPIO_Y33, + EXYNOS5_GPIO_Y34, + EXYNOS5_GPIO_Y35, + EXYNOS5_GPIO_Y36, + EXYNOS5_GPIO_Y37, + EXYNOS5_GPIO_Y40, /* 136 0x88 */ + EXYNOS5_GPIO_Y41, + EXYNOS5_GPIO_Y42, + EXYNOS5_GPIO_Y43, + EXYNOS5_GPIO_Y44, + EXYNOS5_GPIO_Y45, + EXYNOS5_GPIO_Y46, + EXYNOS5_GPIO_Y47, + EXYNOS5_GPIO_Y50, /* 144 0x90 */ + EXYNOS5_GPIO_Y51, + EXYNOS5_GPIO_Y52, + EXYNOS5_GPIO_Y53, + EXYNOS5_GPIO_Y54, + EXYNOS5_GPIO_Y55, + EXYNOS5_GPIO_Y56, + EXYNOS5_GPIO_Y57, + EXYNOS5_GPIO_Y60, /* 152 0x98 */ + EXYNOS5_GPIO_Y61, + EXYNOS5_GPIO_Y62, + EXYNOS5_GPIO_Y63, + EXYNOS5_GPIO_Y64, + EXYNOS5_GPIO_Y65, + EXYNOS5_GPIO_Y66, + EXYNOS5_GPIO_Y67, + + /* GPIO_PART2_STARTS */ + EXYNOS5_GPIO_MAX_PORT_PART_1, /* 160 0xa0 */ + EXYNOS5_GPIO_C40 = EXYNOS5_GPIO_MAX_PORT_PART_1, + EXYNOS5_GPIO_C41, + EXYNOS5_GPIO_C42, + EXYNOS5_GPIO_C43, + EXYNOS5_GPIO_C44, + EXYNOS5_GPIO_C45, + EXYNOS5_GPIO_C46, + EXYNOS5_GPIO_C47, + + /* GPIO_PART3_STARTS */ + EXYNOS5_GPIO_MAX_PORT_PART_2, /* 168 0xa8 */ + EXYNOS5_GPIO_X00 = EXYNOS5_GPIO_MAX_PORT_PART_2, + EXYNOS5_GPIO_X01, + EXYNOS5_GPIO_X02, + EXYNOS5_GPIO_X03, + EXYNOS5_GPIO_X04, + EXYNOS5_GPIO_X05, + EXYNOS5_GPIO_X06, + EXYNOS5_GPIO_X07, + EXYNOS5_GPIO_X10, /* 176 0xb0 */ + EXYNOS5_GPIO_X11, + EXYNOS5_GPIO_X12, + EXYNOS5_GPIO_X13, + EXYNOS5_GPIO_X14, + EXYNOS5_GPIO_X15, + EXYNOS5_GPIO_X16, + EXYNOS5_GPIO_X17, + EXYNOS5_GPIO_X20, /* 184 0xb8 */ + EXYNOS5_GPIO_X21, + EXYNOS5_GPIO_X22, + EXYNOS5_GPIO_X23, + EXYNOS5_GPIO_X24, + EXYNOS5_GPIO_X25, + EXYNOS5_GPIO_X26, + EXYNOS5_GPIO_X27, + EXYNOS5_GPIO_X30, /* 192 0xc0 */ + EXYNOS5_GPIO_X31, + EXYNOS5_GPIO_X32, + EXYNOS5_GPIO_X33, + EXYNOS5_GPIO_X34, + EXYNOS5_GPIO_X35, + EXYNOS5_GPIO_X36, + EXYNOS5_GPIO_X37, + + /* GPIO_PART4_STARTS */ + EXYNOS5_GPIO_MAX_PORT_PART_3, /* 200 0xc8 */ + EXYNOS5_GPIO_E00 = EXYNOS5_GPIO_MAX_PORT_PART_3, + EXYNOS5_GPIO_E01, + EXYNOS5_GPIO_E02, + EXYNOS5_GPIO_E03, + EXYNOS5_GPIO_E04, + EXYNOS5_GPIO_E05, + EXYNOS5_GPIO_E06, + EXYNOS5_GPIO_E07, + EXYNOS5_GPIO_E10, /* 208 0xd0 */ + EXYNOS5_GPIO_E11, + EXYNOS5_GPIO_E12, + EXYNOS5_GPIO_E13, + EXYNOS5_GPIO_E14, + EXYNOS5_GPIO_E15, + EXYNOS5_GPIO_E16, + EXYNOS5_GPIO_E17, + EXYNOS5_GPIO_F00, /* 216 0xd8 */ + EXYNOS5_GPIO_F01, + EXYNOS5_GPIO_F02, + EXYNOS5_GPIO_F03, + EXYNOS5_GPIO_F04, + EXYNOS5_GPIO_F05, + EXYNOS5_GPIO_F06, + EXYNOS5_GPIO_F07, + EXYNOS5_GPIO_F10, /* 224 0xe0 */ + EXYNOS5_GPIO_F11, + EXYNOS5_GPIO_F12, + EXYNOS5_GPIO_F13, + EXYNOS5_GPIO_F14, + EXYNOS5_GPIO_F15, + EXYNOS5_GPIO_F16, + EXYNOS5_GPIO_F17, + EXYNOS5_GPIO_G00, /* 232 0xe8 */ + EXYNOS5_GPIO_G01, + EXYNOS5_GPIO_G02, + EXYNOS5_GPIO_G03, + EXYNOS5_GPIO_G04, + EXYNOS5_GPIO_G05, + EXYNOS5_GPIO_G06, + EXYNOS5_GPIO_G07, + EXYNOS5_GPIO_G10, /* 240 0xf0 */ + EXYNOS5_GPIO_G11, + EXYNOS5_GPIO_G12, + EXYNOS5_GPIO_G13, + EXYNOS5_GPIO_G14, + EXYNOS5_GPIO_G15, + EXYNOS5_GPIO_G16, + EXYNOS5_GPIO_G17, + EXYNOS5_GPIO_G20, /* 248 0xf8 */ + EXYNOS5_GPIO_G21, + EXYNOS5_GPIO_G22, + EXYNOS5_GPIO_G23, + EXYNOS5_GPIO_G24, + EXYNOS5_GPIO_G25, + EXYNOS5_GPIO_G26, + EXYNOS5_GPIO_G27, + EXYNOS5_GPIO_H00, /* 256 0x100 */ + EXYNOS5_GPIO_H01, + EXYNOS5_GPIO_H02, + EXYNOS5_GPIO_H03, + EXYNOS5_GPIO_H04, + EXYNOS5_GPIO_H05, + EXYNOS5_GPIO_H06, + EXYNOS5_GPIO_H07, + EXYNOS5_GPIO_H10, /* 264 0x108 */ + EXYNOS5_GPIO_H11, + EXYNOS5_GPIO_H12, + EXYNOS5_GPIO_H13, + EXYNOS5_GPIO_H14, + EXYNOS5_GPIO_H15, + EXYNOS5_GPIO_H16, + EXYNOS5_GPIO_H17, + + /* GPIO_PART4_STARTS */ + EXYNOS5_GPIO_MAX_PORT_PART_4, /* 272 0x110 */ + EXYNOS5_GPIO_V00 = EXYNOS5_GPIO_MAX_PORT_PART_4, + EXYNOS5_GPIO_V01, + EXYNOS5_GPIO_V02, + EXYNOS5_GPIO_V03, + EXYNOS5_GPIO_V04, + EXYNOS5_GPIO_V05, + EXYNOS5_GPIO_V06, + EXYNOS5_GPIO_V07, + EXYNOS5_GPIO_V10, /* 280 0x118 */ + EXYNOS5_GPIO_V11, + EXYNOS5_GPIO_V12, + EXYNOS5_GPIO_V13, + EXYNOS5_GPIO_V14, + EXYNOS5_GPIO_V15, + EXYNOS5_GPIO_V16, + EXYNOS5_GPIO_V17, + + /* GPIO_PART5_STARTS */ + EXYNOS5_GPIO_MAX_PORT_PART_5, /* 288 0x120 */ + EXYNOS5_GPIO_V20 = EXYNOS5_GPIO_MAX_PORT_PART_5, + EXYNOS5_GPIO_V21, + EXYNOS5_GPIO_V22, + EXYNOS5_GPIO_V23, + EXYNOS5_GPIO_V24, + EXYNOS5_GPIO_V25, + EXYNOS5_GPIO_V26, + EXYNOS5_GPIO_V27, + EXYNOS5_GPIO_V30, /* 296 0x128 */ + EXYNOS5_GPIO_V31, + EXYNOS5_GPIO_V32, + EXYNOS5_GPIO_V33, + EXYNOS5_GPIO_V34, + EXYNOS5_GPIO_V35, + EXYNOS5_GPIO_V36, + EXYNOS5_GPIO_V37, + + /* GPIO_PART6_STARTS */ + EXYNOS5_GPIO_MAX_PORT_PART_6, /* 304 0x130 */ + EXYNOS5_GPIO_V40 = EXYNOS5_GPIO_MAX_PORT_PART_6, + EXYNOS5_GPIO_V41, + EXYNOS5_GPIO_V42, + EXYNOS5_GPIO_V43, + EXYNOS5_GPIO_V44, + EXYNOS5_GPIO_V45, + EXYNOS5_GPIO_V46, + EXYNOS5_GPIO_V47, + + /* GPIO_PART7_STARTS */ /* 312 0x138 */ + EXYNOS5_GPIO_MAX_PORT_PART_7, + EXYNOS5_GPIO_Z0 = EXYNOS5_GPIO_MAX_PORT_PART_7, + EXYNOS5_GPIO_Z1, + EXYNOS5_GPIO_Z2, + EXYNOS5_GPIO_Z3, + EXYNOS5_GPIO_Z4, + EXYNOS5_GPIO_Z5, + EXYNOS5_GPIO_Z6, + EXYNOS5_GPIO_MAX_PORT }; -struct exynos4x12_gpio_part4 { - struct s5p_gpio_bank v0; - struct s5p_gpio_bank v1; - struct s5p_gpio_bank res1[0x1]; - struct s5p_gpio_bank v2; - struct s5p_gpio_bank v3; - struct s5p_gpio_bank res2[0x1]; - struct s5p_gpio_bank v4; +enum exynos5420_gpio_pin { + /* GPIO_PART1_STARTS */ + EXYNOS5420_GPIO_A00, /* 0 */ + EXYNOS5420_GPIO_A01, + EXYNOS5420_GPIO_A02, + EXYNOS5420_GPIO_A03, + EXYNOS5420_GPIO_A04, + EXYNOS5420_GPIO_A05, + EXYNOS5420_GPIO_A06, + EXYNOS5420_GPIO_A07, + EXYNOS5420_GPIO_A10, /* 8 */ + EXYNOS5420_GPIO_A11, + EXYNOS5420_GPIO_A12, + EXYNOS5420_GPIO_A13, + EXYNOS5420_GPIO_A14, + EXYNOS5420_GPIO_A15, + EXYNOS5420_GPIO_A16, + EXYNOS5420_GPIO_A17, + EXYNOS5420_GPIO_A20, /* 16 0x10 */ + EXYNOS5420_GPIO_A21, + EXYNOS5420_GPIO_A22, + EXYNOS5420_GPIO_A23, + EXYNOS5420_GPIO_A24, + EXYNOS5420_GPIO_A25, + EXYNOS5420_GPIO_A26, + EXYNOS5420_GPIO_A27, + EXYNOS5420_GPIO_B00, /* 24 0x18 */ + EXYNOS5420_GPIO_B01, + EXYNOS5420_GPIO_B02, + EXYNOS5420_GPIO_B03, + EXYNOS5420_GPIO_B04, + EXYNOS5420_GPIO_B05, + EXYNOS5420_GPIO_B06, + EXYNOS5420_GPIO_B07, + EXYNOS5420_GPIO_B10, /* 32 0x20 */ + EXYNOS5420_GPIO_B11, + EXYNOS5420_GPIO_B12, + EXYNOS5420_GPIO_B13, + EXYNOS5420_GPIO_B14, + EXYNOS5420_GPIO_B15, + EXYNOS5420_GPIO_B16, + EXYNOS5420_GPIO_B17, + EXYNOS5420_GPIO_B20, /* 40 0x28 */ + EXYNOS5420_GPIO_B21, + EXYNOS5420_GPIO_B22, + EXYNOS5420_GPIO_B23, + EXYNOS5420_GPIO_B24, + EXYNOS5420_GPIO_B25, + EXYNOS5420_GPIO_B26, + EXYNOS5420_GPIO_B27, + EXYNOS5420_GPIO_B30, /* 48 0x30 */ + EXYNOS5420_GPIO_B31, + EXYNOS5420_GPIO_B32, + EXYNOS5420_GPIO_B33, + EXYNOS5420_GPIO_B34, + EXYNOS5420_GPIO_B35, + EXYNOS5420_GPIO_B36, + EXYNOS5420_GPIO_B37, + EXYNOS5420_GPIO_B40, /* 56 0x38 */ + EXYNOS5420_GPIO_B41, + EXYNOS5420_GPIO_B42, + EXYNOS5420_GPIO_B43, + EXYNOS5420_GPIO_B44, + EXYNOS5420_GPIO_B45, + EXYNOS5420_GPIO_B46, + EXYNOS5420_GPIO_B47, + EXYNOS5420_GPIO_H00, /* 64 0x40 */ + EXYNOS5420_GPIO_H01, + EXYNOS5420_GPIO_H02, + EXYNOS5420_GPIO_H03, + EXYNOS5420_GPIO_H04, + EXYNOS5420_GPIO_H05, + EXYNOS5420_GPIO_H06, + EXYNOS5420_GPIO_H07, + + /* GPIO PART 2 STARTS*/ + EXYNOS5420_GPIO_MAX_PORT_PART_1,/* 72 0x48 */ + EXYNOS5420_GPIO_Y70 = EXYNOS5420_GPIO_MAX_PORT_PART_1, + EXYNOS5420_GPIO_Y71, + EXYNOS5420_GPIO_Y72, + EXYNOS5420_GPIO_Y73, + EXYNOS5420_GPIO_Y74, + EXYNOS5420_GPIO_Y75, + EXYNOS5420_GPIO_Y76, + EXYNOS5420_GPIO_Y77, + + /* GPIO PART 3 STARTS*/ + EXYNOS5420_GPIO_MAX_PORT_PART_2,/* 80 0x50 */ + EXYNOS5420_GPIO_X00 = EXYNOS5420_GPIO_MAX_PORT_PART_2, + EXYNOS5420_GPIO_X01, + EXYNOS5420_GPIO_X02, + EXYNOS5420_GPIO_X03, + EXYNOS5420_GPIO_X04, + EXYNOS5420_GPIO_X05, + EXYNOS5420_GPIO_X06, + EXYNOS5420_GPIO_X07, + EXYNOS5420_GPIO_X10, /* 88 0x58 */ + EXYNOS5420_GPIO_X11, + EXYNOS5420_GPIO_X12, + EXYNOS5420_GPIO_X13, + EXYNOS5420_GPIO_X14, + EXYNOS5420_GPIO_X15, + EXYNOS5420_GPIO_X16, + EXYNOS5420_GPIO_X17, + EXYNOS5420_GPIO_X20, /* 96 0x60 */ + EXYNOS5420_GPIO_X21, + EXYNOS5420_GPIO_X22, + EXYNOS5420_GPIO_X23, + EXYNOS5420_GPIO_X24, + EXYNOS5420_GPIO_X25, + EXYNOS5420_GPIO_X26, + EXYNOS5420_GPIO_X27, + EXYNOS5420_GPIO_X30, /* 104 0x68 */ + EXYNOS5420_GPIO_X31, + EXYNOS5420_GPIO_X32, + EXYNOS5420_GPIO_X33, + EXYNOS5420_GPIO_X34, + EXYNOS5420_GPIO_X35, + EXYNOS5420_GPIO_X36, + EXYNOS5420_GPIO_X37, + + /* GPIO PART 4 STARTS*/ + EXYNOS5420_GPIO_MAX_PORT_PART_3,/* 112 0x70 */ + EXYNOS5420_GPIO_C00 = EXYNOS5420_GPIO_MAX_PORT_PART_3, + EXYNOS5420_GPIO_C01, + EXYNOS5420_GPIO_C02, + EXYNOS5420_GPIO_C03, + EXYNOS5420_GPIO_C04, + EXYNOS5420_GPIO_C05, + EXYNOS5420_GPIO_C06, + EXYNOS5420_GPIO_C07, + EXYNOS5420_GPIO_C10, /* 120 0x78 */ + EXYNOS5420_GPIO_C11, + EXYNOS5420_GPIO_C12, + EXYNOS5420_GPIO_C13, + EXYNOS5420_GPIO_C14, + EXYNOS5420_GPIO_C15, + EXYNOS5420_GPIO_C16, + EXYNOS5420_GPIO_C17, + EXYNOS5420_GPIO_C20, /* 128 0x80 */ + EXYNOS5420_GPIO_C21, + EXYNOS5420_GPIO_C22, + EXYNOS5420_GPIO_C23, + EXYNOS5420_GPIO_C24, + EXYNOS5420_GPIO_C25, + EXYNOS5420_GPIO_C26, + EXYNOS5420_GPIO_C27, + EXYNOS5420_GPIO_C30, /* 136 0x88 */ + EXYNOS5420_GPIO_C31, + EXYNOS5420_GPIO_C32, + EXYNOS5420_GPIO_C33, + EXYNOS5420_GPIO_C34, + EXYNOS5420_GPIO_C35, + EXYNOS5420_GPIO_C36, + EXYNOS5420_GPIO_C37, + EXYNOS5420_GPIO_C40, /* 144 0x90 */ + EXYNOS5420_GPIO_C41, + EXYNOS5420_GPIO_C42, + EXYNOS5420_GPIO_C43, + EXYNOS5420_GPIO_C44, + EXYNOS5420_GPIO_C45, + EXYNOS5420_GPIO_C46, + EXYNOS5420_GPIO_C47, + EXYNOS5420_GPIO_D10, /* 152 0x98 */ + EXYNOS5420_GPIO_D11, + EXYNOS5420_GPIO_D12, + EXYNOS5420_GPIO_D13, + EXYNOS5420_GPIO_D14, + EXYNOS5420_GPIO_D15, + EXYNOS5420_GPIO_D16, + EXYNOS5420_GPIO_D17, + EXYNOS5420_GPIO_Y00, /* 160 0xa0 */ + EXYNOS5420_GPIO_Y01, + EXYNOS5420_GPIO_Y02, + EXYNOS5420_GPIO_Y03, + EXYNOS5420_GPIO_Y04, + EXYNOS5420_GPIO_Y05, + EXYNOS5420_GPIO_Y06, + EXYNOS5420_GPIO_Y07, + EXYNOS5420_GPIO_Y10, /* 168 0xa8 */ + EXYNOS5420_GPIO_Y11, + EXYNOS5420_GPIO_Y12, + EXYNOS5420_GPIO_Y13, + EXYNOS5420_GPIO_Y14, + EXYNOS5420_GPIO_Y15, + EXYNOS5420_GPIO_Y16, + EXYNOS5420_GPIO_Y17, + EXYNOS5420_GPIO_Y20, /* 176 0xb0 */ + EXYNOS5420_GPIO_Y21, + EXYNOS5420_GPIO_Y22, + EXYNOS5420_GPIO_Y23, + EXYNOS5420_GPIO_Y24, + EXYNOS5420_GPIO_Y25, + EXYNOS5420_GPIO_Y26, + EXYNOS5420_GPIO_Y27, + EXYNOS5420_GPIO_Y30, /* 184 0xb8 */ + EXYNOS5420_GPIO_Y31, + EXYNOS5420_GPIO_Y32, + EXYNOS5420_GPIO_Y33, + EXYNOS5420_GPIO_Y34, + EXYNOS5420_GPIO_Y35, + EXYNOS5420_GPIO_Y36, + EXYNOS5420_GPIO_Y37, + EXYNOS5420_GPIO_Y40, /* 192 0xc0 */ + EXYNOS5420_GPIO_Y41, + EXYNOS5420_GPIO_Y42, + EXYNOS5420_GPIO_Y43, + EXYNOS5420_GPIO_Y44, + EXYNOS5420_GPIO_Y45, + EXYNOS5420_GPIO_Y46, + EXYNOS5420_GPIO_Y47, + EXYNOS5420_GPIO_Y50, /* 200 0xc8 */ + EXYNOS5420_GPIO_Y51, + EXYNOS5420_GPIO_Y52, + EXYNOS5420_GPIO_Y53, + EXYNOS5420_GPIO_Y54, + EXYNOS5420_GPIO_Y55, + EXYNOS5420_GPIO_Y56, + EXYNOS5420_GPIO_Y57, + EXYNOS5420_GPIO_Y60, /* 208 0xd0 */ + EXYNOS5420_GPIO_Y61, + EXYNOS5420_GPIO_Y62, + EXYNOS5420_GPIO_Y63, + EXYNOS5420_GPIO_Y64, + EXYNOS5420_GPIO_Y65, + EXYNOS5420_GPIO_Y66, + EXYNOS5420_GPIO_Y67, + + /* GPIO_PART5_STARTS */ + EXYNOS5420_GPIO_MAX_PORT_PART_4,/* 216 0xd8 */ + EXYNOS5420_GPIO_E00 = EXYNOS5420_GPIO_MAX_PORT_PART_4, + EXYNOS5420_GPIO_E01, + EXYNOS5420_GPIO_E02, + EXYNOS5420_GPIO_E03, + EXYNOS5420_GPIO_E04, + EXYNOS5420_GPIO_E05, + EXYNOS5420_GPIO_E06, + EXYNOS5420_GPIO_E07, + EXYNOS5420_GPIO_E10, /* 224 0xe0 */ + EXYNOS5420_GPIO_E11, + EXYNOS5420_GPIO_E12, + EXYNOS5420_GPIO_E13, + EXYNOS5420_GPIO_E14, + EXYNOS5420_GPIO_E15, + EXYNOS5420_GPIO_E16, + EXYNOS5420_GPIO_E17, + EXYNOS5420_GPIO_F00, /* 232 0xe8 */ + EXYNOS5420_GPIO_F01, + EXYNOS5420_GPIO_F02, + EXYNOS5420_GPIO_F03, + EXYNOS5420_GPIO_F04, + EXYNOS5420_GPIO_F05, + EXYNOS5420_GPIO_F06, + EXYNOS5420_GPIO_F07, + EXYNOS5420_GPIO_F10, /* 240 0xf0 */ + EXYNOS5420_GPIO_F11, + EXYNOS5420_GPIO_F12, + EXYNOS5420_GPIO_F13, + EXYNOS5420_GPIO_F14, + EXYNOS5420_GPIO_F15, + EXYNOS5420_GPIO_F16, + EXYNOS5420_GPIO_F17, + EXYNOS5420_GPIO_G00, /* 248 0xf8 */ + EXYNOS5420_GPIO_G01, + EXYNOS5420_GPIO_G02, + EXYNOS5420_GPIO_G03, + EXYNOS5420_GPIO_G04, + EXYNOS5420_GPIO_G05, + EXYNOS5420_GPIO_G06, + EXYNOS5420_GPIO_G07, + EXYNOS5420_GPIO_G10, /* 256 0x100 */ + EXYNOS5420_GPIO_G11, + EXYNOS5420_GPIO_G12, + EXYNOS5420_GPIO_G13, + EXYNOS5420_GPIO_G14, + EXYNOS5420_GPIO_G15, + EXYNOS5420_GPIO_G16, + EXYNOS5420_GPIO_G17, + EXYNOS5420_GPIO_G20, /* 264 0x108 */ + EXYNOS5420_GPIO_G21, + EXYNOS5420_GPIO_G22, + EXYNOS5420_GPIO_G23, + EXYNOS5420_GPIO_G24, + EXYNOS5420_GPIO_G25, + EXYNOS5420_GPIO_G26, + EXYNOS5420_GPIO_G27, + EXYNOS5420_GPIO_J40, /* 272 0x110 */ + EXYNOS5420_GPIO_J41, + EXYNOS5420_GPIO_J42, + EXYNOS5420_GPIO_J43, + EXYNOS5420_GPIO_J44, + EXYNOS5420_GPIO_J45, + EXYNOS5420_GPIO_J46, + EXYNOS5420_GPIO_J47, + + /* GPIO_PART6_STARTS */ + EXYNOS5420_GPIO_MAX_PORT_PART_5,/* 280 0x118 */ + EXYNOS5420_GPIO_Z0 = EXYNOS5420_GPIO_MAX_PORT_PART_5, + EXYNOS5420_GPIO_Z1, + EXYNOS5420_GPIO_Z2, + EXYNOS5420_GPIO_Z3, + EXYNOS5420_GPIO_Z4, + EXYNOS5420_GPIO_Z5, + EXYNOS5420_GPIO_Z6, + EXYNOS5420_GPIO_MAX_PORT }; -struct exynos5420_gpio_part1 { - struct s5p_gpio_bank a0; - struct s5p_gpio_bank a1; - struct s5p_gpio_bank a2; - struct s5p_gpio_bank b0; - struct s5p_gpio_bank b1; - struct s5p_gpio_bank b2; - struct s5p_gpio_bank b3; - struct s5p_gpio_bank b4; - struct s5p_gpio_bank h0; +struct gpio_info { + unsigned int reg_addr; /* Address of register for this part */ + unsigned int max_gpio; /* Maximum GPIO in this part */ }; -struct exynos5420_gpio_part2 { - struct s5p_gpio_bank y7; /* 0x1340_0000 */ - struct s5p_gpio_bank res[0x5f]; /* */ - struct s5p_gpio_bank x0; /* 0x1340_0C00 */ - struct s5p_gpio_bank x1; /* 0x1340_0C20 */ - struct s5p_gpio_bank x2; /* 0x1340_0C40 */ - struct s5p_gpio_bank x3; /* 0x1340_0C60 */ +#define EXYNOS4_GPIO_NUM_PARTS 3 +static struct gpio_info exynos4_gpio_data[EXYNOS4_GPIO_NUM_PARTS] = { + { EXYNOS4_GPIO_PART1_BASE, EXYNOS4_GPIO_MAX_PORT_PART_1 }, + { EXYNOS4_GPIO_PART2_BASE, EXYNOS4_GPIO_MAX_PORT_PART_2 }, + { EXYNOS4_GPIO_PART3_BASE, EXYNOS4_GPIO_MAX_PORT }, }; -struct exynos5420_gpio_part3 { - struct s5p_gpio_bank c0; - struct s5p_gpio_bank c1; - struct s5p_gpio_bank c2; - struct s5p_gpio_bank c3; - struct s5p_gpio_bank c4; - struct s5p_gpio_bank d1; - struct s5p_gpio_bank y0; - struct s5p_gpio_bank y1; - struct s5p_gpio_bank y2; - struct s5p_gpio_bank y3; - struct s5p_gpio_bank y4; - struct s5p_gpio_bank y5; - struct s5p_gpio_bank y6; +#define EXYNOS4X12_GPIO_NUM_PARTS 4 +static struct gpio_info exynos4x12_gpio_data[EXYNOS4X12_GPIO_NUM_PARTS] = { + { EXYNOS4X12_GPIO_PART1_BASE, EXYNOS4X12_GPIO_MAX_PORT_PART_1 }, + { EXYNOS4X12_GPIO_PART2_BASE, EXYNOS4X12_GPIO_MAX_PORT_PART_2 }, + { EXYNOS4X12_GPIO_PART3_BASE, EXYNOS4X12_GPIO_MAX_PORT_PART_3 }, + { EXYNOS4X12_GPIO_PART4_BASE, EXYNOS4X12_GPIO_MAX_PORT }, }; -struct exynos5420_gpio_part4 { - struct s5p_gpio_bank e0; /* 0x1400_0000 */ - struct s5p_gpio_bank e1; /* 0x1400_0020 */ - struct s5p_gpio_bank f0; /* 0x1400_0040 */ - struct s5p_gpio_bank f1; /* 0x1400_0060 */ - struct s5p_gpio_bank g0; /* 0x1400_0080 */ - struct s5p_gpio_bank g1; /* 0x1400_00A0 */ - struct s5p_gpio_bank g2; /* 0x1400_00C0 */ - struct s5p_gpio_bank j4; /* 0x1400_00E0 */ +#define EXYNOS5_GPIO_NUM_PARTS 8 +static struct gpio_info exynos5_gpio_data[EXYNOS5_GPIO_NUM_PARTS] = { + { EXYNOS5_GPIO_PART1_BASE, EXYNOS5_GPIO_MAX_PORT_PART_1 }, + { EXYNOS5_GPIO_PART2_BASE, EXYNOS5_GPIO_MAX_PORT_PART_2 }, + { EXYNOS5_GPIO_PART3_BASE, EXYNOS5_GPIO_MAX_PORT_PART_3 }, + { EXYNOS5_GPIO_PART4_BASE, EXYNOS5_GPIO_MAX_PORT_PART_4 }, + { EXYNOS5_GPIO_PART5_BASE, EXYNOS5_GPIO_MAX_PORT_PART_5 }, + { EXYNOS5_GPIO_PART6_BASE, EXYNOS5_GPIO_MAX_PORT_PART_6 }, + { EXYNOS5_GPIO_PART7_BASE, EXYNOS5_GPIO_MAX_PORT_PART_7 }, + { EXYNOS5_GPIO_PART8_BASE, EXYNOS5_GPIO_MAX_PORT }, }; -struct exynos5420_gpio_part5 { - struct s5p_gpio_bank z0; /* 0x0386_0000 */ +#define EXYNOS5420_GPIO_NUM_PARTS 6 +static struct gpio_info exynos5420_gpio_data[EXYNOS5420_GPIO_NUM_PARTS] = { + { EXYNOS5420_GPIO_PART1_BASE, EXYNOS5420_GPIO_MAX_PORT_PART_1 }, + { EXYNOS5420_GPIO_PART2_BASE, EXYNOS5420_GPIO_MAX_PORT_PART_2 }, + { EXYNOS5420_GPIO_PART3_BASE, EXYNOS5420_GPIO_MAX_PORT_PART_3 }, + { EXYNOS5420_GPIO_PART4_BASE, EXYNOS5420_GPIO_MAX_PORT_PART_4 }, + { EXYNOS5420_GPIO_PART5_BASE, EXYNOS5420_GPIO_MAX_PORT_PART_5 }, + { EXYNOS5420_GPIO_PART6_BASE, EXYNOS5420_GPIO_MAX_PORT }, }; -struct exynos5_gpio_part1 { - struct s5p_gpio_bank a0; - struct s5p_gpio_bank a1; - struct s5p_gpio_bank a2; - struct s5p_gpio_bank b0; - struct s5p_gpio_bank b1; - struct s5p_gpio_bank b2; - struct s5p_gpio_bank b3; - struct s5p_gpio_bank c0; - struct s5p_gpio_bank c1; - struct s5p_gpio_bank c2; - struct s5p_gpio_bank c3; - struct s5p_gpio_bank d0; - struct s5p_gpio_bank d1; - struct s5p_gpio_bank y0; - struct s5p_gpio_bank y1; - struct s5p_gpio_bank y2; - struct s5p_gpio_bank y3; - struct s5p_gpio_bank y4; - struct s5p_gpio_bank y5; - struct s5p_gpio_bank y6; - struct s5p_gpio_bank res1[0x3]; - struct s5p_gpio_bank c4; - struct s5p_gpio_bank res2[0x48]; - struct s5p_gpio_bank x0; - struct s5p_gpio_bank x1; - struct s5p_gpio_bank x2; - struct s5p_gpio_bank x3; +static inline struct gpio_info *get_gpio_data(void) +{ + if (cpu_is_exynos5()) { + if (proid_is_exynos5420()) + return exynos5420_gpio_data; + else + return exynos5_gpio_data; + } else if (cpu_is_exynos4()) { + if (proid_is_exynos4412()) + return exynos4x12_gpio_data; + else + return exynos4_gpio_data; + } + + return NULL; +} + +static inline unsigned int get_bank_num(void) +{ + if (cpu_is_exynos5()) { + if (proid_is_exynos5420()) + return EXYNOS5420_GPIO_NUM_PARTS; + else + return EXYNOS5_GPIO_NUM_PARTS; + } else if (cpu_is_exynos4()) { + if (proid_is_exynos4412()) + return EXYNOS4X12_GPIO_NUM_PARTS; + else + return EXYNOS4_GPIO_NUM_PARTS; + } + + return 0; +} + +/* + * This structure helps mapping symbolic GPIO names into indices from + * exynos5_gpio_pin/exynos5420_gpio_pin enums. + * + * By convention, symbolic GPIO name is defined as follows: + * + * g[p]<bank><set><bit>, where + * p is optional + * <bank> - a single character bank name, as defined by the SOC + * <set> - a single digit set number + * <bit> - bit number within the set (in 0..7 range). + * + * <set><bit> essentially form an octal number of the GPIO pin within the bank + * space. On the 5420 architecture some banks' sets do not start not from zero + * ('d' starts from 1 and 'j' starts from 4). To compensate for that and + * maintain flat number space withoout holes, those banks use offsets to be + * deducted from the pin number. + */ +struct gpio_name_num_table { + char bank; /* bank name symbol */ + unsigned int bank_size; /* total number of pins in the bank */ + char bank_offset; /* offset of the first bank's pin */ + unsigned int base; /* index of the first bank's pin in the enum */ }; -struct exynos5_gpio_part2 { - struct s5p_gpio_bank e0; - struct s5p_gpio_bank e1; - struct s5p_gpio_bank f0; - struct s5p_gpio_bank f1; - struct s5p_gpio_bank g0; - struct s5p_gpio_bank g1; - struct s5p_gpio_bank g2; - struct s5p_gpio_bank h0; - struct s5p_gpio_bank h1; +#define GPIO_ENTRY(name, base, top, offset) { name, top - base, offset, base } +static const struct gpio_name_num_table exynos4_gpio_table[] = { + GPIO_ENTRY('a', EXYNOS4_GPIO_A00, EXYNOS4_GPIO_B0, 0), + GPIO_ENTRY('b', EXYNOS4_GPIO_B0, EXYNOS4_GPIO_C00, 0), + GPIO_ENTRY('c', EXYNOS4_GPIO_C00, EXYNOS4_GPIO_D00, 0), + GPIO_ENTRY('d', EXYNOS4_GPIO_D00, EXYNOS4_GPIO_E00, 0), + GPIO_ENTRY('e', EXYNOS4_GPIO_E00, EXYNOS4_GPIO_F00, 0), + GPIO_ENTRY('f', EXYNOS4_GPIO_F00, EXYNOS4_GPIO_J00, 0), + GPIO_ENTRY('j', EXYNOS4_GPIO_J00, EXYNOS4_GPIO_K00, 0), + GPIO_ENTRY('k', EXYNOS4_GPIO_K00, EXYNOS4_GPIO_L00, 0), + GPIO_ENTRY('l', EXYNOS4_GPIO_L00, EXYNOS4_GPIO_Y00, 0), + GPIO_ENTRY('y', EXYNOS4_GPIO_Y00, EXYNOS4_GPIO_X00, 0), + GPIO_ENTRY('x', EXYNOS4_GPIO_X00, EXYNOS4_GPIO_Z0, 0), + GPIO_ENTRY('z', EXYNOS4_GPIO_Z0, EXYNOS4_GPIO_MAX_PORT, 0), + { 0 } }; -struct exynos5_gpio_part3 { - struct s5p_gpio_bank v0; - struct s5p_gpio_bank v1; - struct s5p_gpio_bank res1[0x1]; - struct s5p_gpio_bank v2; - struct s5p_gpio_bank v3; - struct s5p_gpio_bank res2[0x1]; - struct s5p_gpio_bank v4; +static const struct gpio_name_num_table exynos4x12_gpio_table[] = { + GPIO_ENTRY('a', EXYNOS4X12_GPIO_A00, EXYNOS4X12_GPIO_B0, 0), + GPIO_ENTRY('b', EXYNOS4X12_GPIO_B0, EXYNOS4X12_GPIO_C00, 0), + GPIO_ENTRY('c', EXYNOS4X12_GPIO_C00, EXYNOS4X12_GPIO_D00, 0), + GPIO_ENTRY('d', EXYNOS4X12_GPIO_D00, EXYNOS4X12_GPIO_F00, 0), + GPIO_ENTRY('f', EXYNOS4X12_GPIO_F00, EXYNOS4X12_GPIO_J00, 0), + GPIO_ENTRY('j', EXYNOS4X12_GPIO_J00, EXYNOS4X12_GPIO_K00, 0), + GPIO_ENTRY('k', EXYNOS4X12_GPIO_K00, EXYNOS4X12_GPIO_L00, 0), + GPIO_ENTRY('l', EXYNOS4X12_GPIO_L00, EXYNOS4X12_GPIO_Y00, 0), + GPIO_ENTRY('y', EXYNOS4X12_GPIO_Y00, EXYNOS4X12_GPIO_M00, 0), + GPIO_ENTRY('m', EXYNOS4X12_GPIO_M00, EXYNOS4X12_GPIO_X00, 0), + GPIO_ENTRY('x', EXYNOS4X12_GPIO_X00, EXYNOS4X12_GPIO_Z0, 0), + GPIO_ENTRY('z', EXYNOS4X12_GPIO_Z0, EXYNOS4X12_GPIO_V00, 0), + GPIO_ENTRY('v', EXYNOS4X12_GPIO_V00, EXYNOS4X12_GPIO_MAX_PORT, 0), + { 0 } }; -struct exynos5_gpio_part4 { - struct s5p_gpio_bank z; +static const struct gpio_name_num_table exynos5_gpio_table[] = { + GPIO_ENTRY('a', EXYNOS5_GPIO_A00, EXYNOS5_GPIO_B00, 0), + GPIO_ENTRY('b', EXYNOS5_GPIO_B00, EXYNOS5_GPIO_C00, 0), + GPIO_ENTRY('c', EXYNOS5_GPIO_C00, EXYNOS5_GPIO_D00, 0), + GPIO_ENTRY('d', EXYNOS5_GPIO_D00, EXYNOS5_GPIO_Y00, 0), + GPIO_ENTRY('y', EXYNOS5_GPIO_Y00, EXYNOS5_GPIO_C40, 0), + GPIO_ENTRY('x', EXYNOS5_GPIO_X00, EXYNOS5_GPIO_E00, 0), + GPIO_ENTRY('e', EXYNOS5_GPIO_E00, EXYNOS5_GPIO_F00, 0), + GPIO_ENTRY('f', EXYNOS5_GPIO_F00, EXYNOS5_GPIO_G00, 0), + GPIO_ENTRY('g', EXYNOS5_GPIO_G00, EXYNOS5_GPIO_H00, 0), + GPIO_ENTRY('h', EXYNOS5_GPIO_H00, EXYNOS5_GPIO_V00, 0), + GPIO_ENTRY('v', EXYNOS5_GPIO_V00, EXYNOS5_GPIO_Z0, 0), + GPIO_ENTRY('z', EXYNOS5_GPIO_Z0, EXYNOS5_GPIO_MAX_PORT, 0), + { 0 } }; -/* functions */ -void s5p_gpio_cfg_pin(struct s5p_gpio_bank *bank, int gpio, int cfg); -void s5p_gpio_direction_output(struct s5p_gpio_bank *bank, int gpio, int en); -void s5p_gpio_direction_input(struct s5p_gpio_bank *bank, int gpio); -void s5p_gpio_set_value(struct s5p_gpio_bank *bank, int gpio, int en); -unsigned int s5p_gpio_get_value(struct s5p_gpio_bank *bank, int gpio); -void s5p_gpio_set_pull(struct s5p_gpio_bank *bank, int gpio, int mode); -void s5p_gpio_set_drv(struct s5p_gpio_bank *bank, int gpio, int mode); -void s5p_gpio_set_rate(struct s5p_gpio_bank *bank, int gpio, int mode); +static const struct gpio_name_num_table exynos5420_gpio_table[] = { + GPIO_ENTRY('a', EXYNOS5420_GPIO_A00, EXYNOS5420_GPIO_B00, 0), + GPIO_ENTRY('b', EXYNOS5420_GPIO_B00, EXYNOS5420_GPIO_H00, 0), + GPIO_ENTRY('h', EXYNOS5420_GPIO_H00, EXYNOS5420_GPIO_Y70, 0), + GPIO_ENTRY('x', EXYNOS5420_GPIO_X00, EXYNOS5420_GPIO_C00, 0), + GPIO_ENTRY('c', EXYNOS5420_GPIO_C00, EXYNOS5420_GPIO_D10, 0), + GPIO_ENTRY('d', EXYNOS5420_GPIO_D10, EXYNOS5420_GPIO_Y00, 010), + GPIO_ENTRY('y', EXYNOS5420_GPIO_Y00, EXYNOS5420_GPIO_E00, 0), + GPIO_ENTRY('e', EXYNOS5420_GPIO_E00, EXYNOS5420_GPIO_F00, 0), + GPIO_ENTRY('f', EXYNOS5420_GPIO_F00, EXYNOS5420_GPIO_G00, 0), + GPIO_ENTRY('g', EXYNOS5420_GPIO_G00, EXYNOS5420_GPIO_J40, 0), + GPIO_ENTRY('j', EXYNOS5420_GPIO_J40, EXYNOS5420_GPIO_Z0, 040), + GPIO_ENTRY('z', EXYNOS5420_GPIO_Z0, EXYNOS5420_GPIO_MAX_PORT, 0), + { 0 } +}; -/* GPIO pins per bank */ -#define GPIO_PER_BANK 8 -#define S5P_GPIO_PART_SHIFT (24) -#define S5P_GPIO_PART_MASK (0xff) -#define S5P_GPIO_BANK_SHIFT (8) -#define S5P_GPIO_BANK_MASK (0xffff) -#define S5P_GPIO_PIN_MASK (0xff) - -#define S5P_GPIO_SET_PART(x) \ - (((x) & S5P_GPIO_PART_MASK) << S5P_GPIO_PART_SHIFT) - -#define S5P_GPIO_GET_PART(x) \ - (((x) >> S5P_GPIO_PART_SHIFT) & S5P_GPIO_PART_MASK) - -#define S5P_GPIO_SET_PIN(x) \ - ((x) & S5P_GPIO_PIN_MASK) - -#define EXYNOS4_GPIO_SET_BANK(part, bank) \ - ((((unsigned)&(((struct exynos4_gpio_part##part *) \ - EXYNOS4_GPIO_PART##part##_BASE)->bank) \ - - EXYNOS4_GPIO_PART##part##_BASE) \ - & S5P_GPIO_BANK_MASK) << S5P_GPIO_BANK_SHIFT) - -#define EXYNOS4X12_GPIO_SET_BANK(part, bank) \ - ((((unsigned)&(((struct exynos4x12_gpio_part##part *) \ - EXYNOS4X12_GPIO_PART##part##_BASE)->bank) \ - - EXYNOS4X12_GPIO_PART##part##_BASE) \ - & S5P_GPIO_BANK_MASK) << S5P_GPIO_BANK_SHIFT) - -#define EXYNOS5_GPIO_SET_BANK(part, bank) \ - ((((unsigned)&(((struct exynos5420_gpio_part##part *) \ - EXYNOS5420_GPIO_PART##part##_BASE)->bank) \ - - EXYNOS5_GPIO_PART##part##_BASE) \ - & S5P_GPIO_BANK_MASK) << S5P_GPIO_BANK_SHIFT) - -#define EXYNOS5420_GPIO_SET_BANK(part, bank) \ - ((((unsigned)&(((struct exynos5420_gpio_part##part *) \ - EXYNOS5420_GPIO_PART##part##_BASE)->bank) \ - - EXYNOS5420_GPIO_PART##part##_BASE) \ - & S5P_GPIO_BANK_MASK) << S5P_GPIO_BANK_SHIFT) - -#define exynos4_gpio_get(part, bank, pin) \ - (S5P_GPIO_SET_PART(part) | \ - EXYNOS4_GPIO_SET_BANK(part, bank) | \ - S5P_GPIO_SET_PIN(pin)) - -#define exynos4x12_gpio_get(part, bank, pin) \ - (S5P_GPIO_SET_PART(part) | \ - EXYNOS4X12_GPIO_SET_BANK(part, bank) | \ - S5P_GPIO_SET_PIN(pin)) - -#define exynos5420_gpio_get(part, bank, pin) \ - (S5P_GPIO_SET_PART(part) | \ - EXYNOS5420_GPIO_SET_BANK(part, bank) | \ - S5P_GPIO_SET_PIN(pin)) - -#define exynos5_gpio_get(part, bank, pin) \ - (S5P_GPIO_SET_PART(part) | \ - EXYNOS5_GPIO_SET_BANK(part, bank) | \ - S5P_GPIO_SET_PIN(pin)) - -static inline unsigned int s5p_gpio_base(int gpio) -{ - unsigned gpio_part = S5P_GPIO_GET_PART(gpio); - - switch (gpio_part) { - case 1: - return samsung_get_base_gpio_part1(); - case 2: - return samsung_get_base_gpio_part2(); - case 3: - return samsung_get_base_gpio_part3(); - case 4: - return samsung_get_base_gpio_part4(); - default: - return 0; - } -} +void gpio_cfg_pin(int gpio, int cfg); +void gpio_set_pull(int gpio, int mode); +void gpio_set_drv(int gpio, int mode); +int gpio_direction_output(unsigned gpio, int value); +int gpio_set_value(unsigned gpio, int value); +int gpio_get_value(unsigned gpio); +void gpio_set_rate(int gpio, int mode); +struct s5p_gpio_bank *s5p_gpio_get_bank(unsigned gpio); +int s5p_gpio_get_pin(unsigned gpio); #endif /* Pin configurations */ -#define GPIO_INPUT 0x0 -#define GPIO_OUTPUT 0x1 -#define GPIO_IRQ 0xf -#define GPIO_FUNC(x) (x) +#define S5P_GPIO_INPUT 0x0 +#define S5P_GPIO_OUTPUT 0x1 +#define S5P_GPIO_IRQ 0xf +#define S5P_GPIO_FUNC(x) (x) /* Pull mode */ -#define GPIO_PULL_NONE 0x0 -#define GPIO_PULL_DOWN 0x1 -#define GPIO_PULL_UP 0x3 +#define S5P_GPIO_PULL_NONE 0x0 +#define S5P_GPIO_PULL_DOWN 0x1 +#define S5P_GPIO_PULL_UP 0x3 /* Drive Strength level */ -#define GPIO_DRV_1X 0x0 -#define GPIO_DRV_3X 0x1 -#define GPIO_DRV_2X 0x2 -#define GPIO_DRV_4X 0x3 -#define GPIO_DRV_FAST 0x0 -#define GPIO_DRV_SLOW 0x1 +#define S5P_GPIO_DRV_1X 0x0 +#define S5P_GPIO_DRV_3X 0x1 +#define S5P_GPIO_DRV_2X 0x2 +#define S5P_GPIO_DRV_4X 0x3 +#define S5P_GPIO_DRV_FAST 0x0 +#define S5P_GPIO_DRV_SLOW 0x1 #endif diff --git a/arch/arm/include/asm/arch-mx25/imx-regs.h b/arch/arm/include/asm/arch-mx25/imx-regs.h index a17f828342..3dffa4a396 100644 --- a/arch/arm/include/asm/arch-mx25/imx-regs.h +++ b/arch/arm/include/asm/arch-mx25/imx-regs.h @@ -161,6 +161,126 @@ struct aips_regs { u32 mpr_0_7; u32 mpr_8_15; }; +/* LCD controller registers */ +struct lcdc_regs { + u32 lssar; /* Screen Start Address */ + u32 lsr; /* Size */ + u32 lvpwr; /* Virtual Page Width */ + u32 lcpr; /* Cursor Position */ + u32 lcwhb; /* Cursor Width Height and Blink */ + u32 lccmr; /* Color Cursor Mapping */ + u32 lpcr; /* Panel Configuration */ + u32 lhcr; /* Horizontal Configuration */ + u32 lvcr; /* Vertical Configuration */ + u32 lpor; /* Panning Offset */ + u32 lscr; /* Sharp Configuration */ + u32 lpccr; /* PWM Contrast Control */ + u32 ldcr; /* DMA Control */ + u32 lrmcr; /* Refresh Mode Control */ + u32 licr; /* Interrupt Configuration */ + u32 lier; /* Interrupt Enable */ + u32 lisr; /* Interrupt Status */ + u32 res0[3]; + u32 lgwsar; /* Graphic Window Start Address */ + u32 lgwsr; /* Graphic Window Size */ + u32 lgwvpwr; /* Graphic Window Virtual Page Width Regist */ + u32 lgwpor; /* Graphic Window Panning Offset */ + u32 lgwpr; /* Graphic Window Position */ + u32 lgwcr; /* Graphic Window Control */ + u32 lgwdcr; /* Graphic Window DMA Control */ + u32 res1[5]; + u32 lauscr; /* AUS Mode Control */ + u32 lausccr; /* AUS mode Cursor Control */ + u32 res2[31 + 64*7]; + u32 bglut; /* Background Lookup Table */ + u32 gwlut; /* Graphic Window Lookup Table */ +}; + +/* Wireless External Interface Module Registers */ +struct weim_regs { + u32 cscr0u; /* Chip Select 0 Upper Register */ + u32 cscr0l; /* Chip Select 0 Lower Register */ + u32 cscr0a; /* Chip Select 0 Addition Register */ + u32 pad0; + u32 cscr1u; /* Chip Select 1 Upper Register */ + u32 cscr1l; /* Chip Select 1 Lower Register */ + u32 cscr1a; /* Chip Select 1 Addition Register */ + u32 pad1; + u32 cscr2u; /* Chip Select 2 Upper Register */ + u32 cscr2l; /* Chip Select 2 Lower Register */ + u32 cscr2a; /* Chip Select 2 Addition Register */ + u32 pad2; + u32 cscr3u; /* Chip Select 3 Upper Register */ + u32 cscr3l; /* Chip Select 3 Lower Register */ + u32 cscr3a; /* Chip Select 3 Addition Register */ + u32 pad3; + u32 cscr4u; /* Chip Select 4 Upper Register */ + u32 cscr4l; /* Chip Select 4 Lower Register */ + u32 cscr4a; /* Chip Select 4 Addition Register */ + u32 pad4; + u32 cscr5u; /* Chip Select 5 Upper Register */ + u32 cscr5l; /* Chip Select 5 Lower Register */ + u32 cscr5a; /* Chip Select 5 Addition Register */ + u32 pad5; + u32 wcr; /* WEIM Configuration Register */ +}; + +/* Multi-Master Memory Interface */ +struct m3if_regs { + u32 ctl; /* Control Register */ + u32 wcfg0; /* Watermark Configuration Register 0 */ + u32 wcfg1; /* Watermark Configuration Register1 */ + u32 wcfg2; /* Watermark Configuration Register2 */ + u32 wcfg3; /* Watermark Configuration Register 3 */ + u32 wcfg4; /* Watermark Configuration Register 4 */ + u32 wcfg5; /* Watermark Configuration Register 5 */ + u32 wcfg6; /* Watermark Configuration Register 6 */ + u32 wcfg7; /* Watermark Configuration Register 7 */ + u32 wcsr; /* Watermark Control and Status Register */ + u32 scfg0; /* Snooping Configuration Register 0 */ + u32 scfg1; /* Snooping Configuration Register 1 */ + u32 scfg2; /* Snooping Configuration Register 2 */ + u32 ssr0; /* Snooping Status Register 0 */ + u32 ssr1; /* Snooping Status Register 1 */ + u32 res0; + u32 mlwe0; /* Master Lock WEIM CS0 Register */ + u32 mlwe1; /* Master Lock WEIM CS1 Register */ + u32 mlwe2; /* Master Lock WEIM CS2 Register */ + u32 mlwe3; /* Master Lock WEIM CS3 Register */ + u32 mlwe4; /* Master Lock WEIM CS4 Register */ + u32 mlwe5; /* Master Lock WEIM CS5 Register */ +}; + +/* Pulse width modulation */ +struct pwm_regs { + u32 cr; /* Control Register */ + u32 sr; /* Status Register */ + u32 ir; /* Interrupt Register */ + u32 sar; /* Sample Register */ + u32 pr; /* Period Register */ + u32 cnr; /* Counter Register */ +}; + +/* Enhanced Periodic Interrupt Timer */ +struct epit_regs { + u32 cr; /* Control register */ + u32 sr; /* Status register */ + u32 lr; /* Load register */ + u32 cmpr; /* Compare register */ + u32 cnr; /* Counter register */ +}; + +/* CSPI registers */ +struct cspi_regs { + u32 rxdata; + u32 txdata; + u32 ctrl; + u32 intr; + u32 dma; + u32 stat; + u32 period; + u32 test; +}; #endif @@ -289,6 +409,8 @@ struct aips_regs { #define CCM_PERCLK_MASK 0x3f #define CCM_RCSR_NF_16BIT_SEL (1 << 14) #define CCM_RCSR_NF_PS(v) ((v >> 26) & 3) +#define CCM_CRDR_BT_UART_SRC_SHIFT 29 +#define CCM_CRDR_BT_UART_SRC_MASK 7 /* ESDRAM Controller register bitfields */ #define ESDCTL_PRCT(x) (((x) & 0x3f) << 0) @@ -345,12 +467,65 @@ struct aips_regs { #define WSR_UNLOCK1 0x5555 #define WSR_UNLOCK2 0xAAAA +/* MAX bits */ +#define MAX_MGPCR_AULB(x) (((x) & 0x7) << 0) + +/* M3IF bits */ +#define M3IF_CTL_MRRP(x) (((x) & 0xff) << 0) + +/* WEIM bits */ +/* 13 fields of the upper CS control register */ +#define WEIM_CSCR_U(sp, wp, bcd, bcs, psz, pme, sync, dol, \ + cnc, wsc, ew, wws, edc) \ + ((sp) << 31 | (wp) << 30 | (bcd) << 28 | (bcs) << 24 | \ + (psz) << 22 | (pme) << 21 | (sync) << 20 | (dol) << 16 | \ + (cnc) << 14 | (wsc) << 8 | (ew) << 7 | (wws) << 4 | (edc) << 0) +/* 12 fields of the lower CS control register */ +#define WEIM_CSCR_L(oea, oen, ebwa, ebwn, \ + csa, ebc, dsz, csn, psr, cre, wrap, csen) \ + ((oea) << 28 | (oen) << 24 | (ebwa) << 20 | (ebwn) << 16 |\ + (csa) << 12 | (ebc) << 11 | (dsz) << 8 | (csn) << 4 |\ + (psr) << 3 | (cre) << 2 | (wrap) << 1 | (csen) << 0) +/* 14 fields of the additional CS control register */ +#define WEIM_CSCR_A(ebra, ebrn, rwa, rwn, mum, lah, lbn, lba, dww, dct, \ + wwu, age, cnc2, fce) \ + ((ebra) << 28 | (ebrn) << 24 | (rwa) << 20 | (rwn) << 16 |\ + (mum) << 15 | (lah) << 13 | (lbn) << 10 | (lba) << 8 |\ + (dww) << 6 | (dct) << 4 | (wwu) << 3 |\ + (age) << 2 | (cnc2) << 1 | (fce) << 0) + /* Names used in GPIO driver */ #define GPIO1_BASE_ADDR IMX_GPIO1_BASE #define GPIO2_BASE_ADDR IMX_GPIO2_BASE #define GPIO3_BASE_ADDR IMX_GPIO3_BASE #define GPIO4_BASE_ADDR IMX_GPIO4_BASE +/* + * CSPI register definitions + */ +#define MXC_CSPI +#define MXC_CSPICTRL_EN (1 << 0) +#define MXC_CSPICTRL_MODE (1 << 1) +#define MXC_CSPICTRL_XCH (1 << 2) +#define MXC_CSPICTRL_SMC (1 << 3) +#define MXC_CSPICTRL_POL (1 << 4) +#define MXC_CSPICTRL_PHA (1 << 5) +#define MXC_CSPICTRL_SSCTL (1 << 6) +#define MXC_CSPICTRL_SSPOL (1 << 7) +#define MXC_CSPICTRL_CHIPSELECT(x) (((x) & 0x3) << 12) +#define MXC_CSPICTRL_BITCOUNT(x) (((x) & 0xfff) << 20) +#define MXC_CSPICTRL_DATARATE(x) (((x) & 0x7) << 16) +#define MXC_CSPICTRL_TC (1 << 7) +#define MXC_CSPICTRL_RXOVF (1 << 6) +#define MXC_CSPICTRL_MAXBITS 0xfff +#define MXC_CSPIPERIOD_32KHZ (1 << 15) +#define MAX_SPI_BYTES 4 + +#define MXC_SPI_BASE_ADDRESSES \ + IMX_CSPI1_BASE, \ + IMX_CSPI2_BASE, \ + IMX_CSPI3_BASE + #define CHIP_REV_1_0 0x10 #define CHIP_REV_1_1 0x11 #define CHIP_REV_1_2 0x12 diff --git a/arch/arm/include/asm/arch-mx6/mx6sl_pins.h b/arch/arm/include/asm/arch-mx6/mx6sl_pins.h index 5f9c90ad87..045ccc4512 100644 --- a/arch/arm/include/asm/arch-mx6/mx6sl_pins.h +++ b/arch/arm/include/asm/arch-mx6/mx6sl_pins.h @@ -10,6 +10,10 @@ #include <asm/imx-common/iomux-v3.h> enum { + MX6_PAD_ECSPI1_MISO__ECSPI_MISO = IOMUX_PAD(0x0358, 0x0068, 0, 0x0684, 0, 0), + MX6_PAD_ECSPI1_MOSI__ECSPI_MOSI = IOMUX_PAD(0x035C, 0x006C, 0, 0x0688, 0, 0), + MX6_PAD_ECSPI1_SCLK__ECSPI_SCLK = IOMUX_PAD(0x0360, 0x0070, 0, 0x067C, 0, 0), + MX6_PAD_ECSPI1_SS0__GPIO4_IO11 = IOMUX_PAD(0x0364, 0x0074, 5, 0x0000, 0, 0), MX6_PAD_SD2_CLK__USDHC2_CLK = IOMUX_PAD(0x055C, 0x0254, 0, 0x0000, 0, 0), MX6_PAD_SD2_CMD__USDHC2_CMD = IOMUX_PAD(0x0560, 0x0258, 0, 0x0000, 0, 0), MX6_PAD_SD2_DAT0__USDHC2_DAT0 = IOMUX_PAD(0x0564, 0x025C, 0, 0x0000, 0, 0), diff --git a/arch/arm/include/asm/arch-omap5/clock.h b/arch/arm/include/asm/arch-omap5/clock.h index 2dfe4efb4b..30d9de2764 100644 --- a/arch/arm/include/asm/arch-omap5/clock.h +++ b/arch/arm/include/asm/arch-omap5/clock.h @@ -322,6 +322,9 @@ #define V_SCLK V_OSCK +/* CKO buffer control */ +#define CKOBUFFER_CLK_ENABLE_MASK (1 << 28) + /* AUXCLKx reg fields */ #define AUXCLK_ENABLE_MASK (1 << 8) #define AUXCLK_SRCSELECT_SHIFT 1 diff --git a/arch/arm/include/asm/arch-omap5/omap.h b/arch/arm/include/asm/arch-omap5/omap.h index 19fdecec01..e35a81a8af 100644 --- a/arch/arm/include/asm/arch-omap5/omap.h +++ b/arch/arm/include/asm/arch-omap5/omap.h @@ -50,6 +50,7 @@ #define UART1_BASE (OMAP54XX_L4_PER_BASE + 0x6a000) #define UART2_BASE (OMAP54XX_L4_PER_BASE + 0x6c000) #define UART3_BASE (OMAP54XX_L4_PER_BASE + 0x20000) +#define UART4_BASE (OMAP54XX_L4_PER_BASE + 0x6e000) /* General Purpose Timers */ #define GPT1_BASE (OMAP54XX_L4_WKUP_BASE + 0x18000) diff --git a/arch/arm/include/asm/arch-rmobile/r8a7790.h b/arch/arm/include/asm/arch-rmobile/r8a7790.h index d9ea71fa14..6ef665d583 100644 --- a/arch/arm/include/asm/arch-rmobile/r8a7790.h +++ b/arch/arm/include/asm/arch-rmobile/r8a7790.h @@ -1,615 +1,18 @@ /* * arch/arm/include/asm/arch-rmobile/r8a7790.h * - * Copyright (C) 2013 Renesas Electronics Corporation + * Copyright (C) 2013,2014 Renesas Electronics Corporation * * SPDX-License-Identifier: GPL-2.0 - */ +*/ #ifndef __ASM_ARCH_R8A7790_H #define __ASM_ARCH_R8A7790_H -/* - * R8A7790 I/O Addresses - */ -#define RWDT_BASE 0xE6020000 -#define SWDT_BASE 0xE6030000 -#define LBSC_BASE 0xFEC00200 -#define DBSC3_0_BASE 0xE6790000 -#define DBSC3_1_BASE 0xE67A0000 -#define TMU_BASE 0xE61E0000 -#define GPIO5_BASE 0xE6055000 -#define SH_QSPI_BASE 0xE6B10000 - -#define S3C_BASE 0xE6784000 -#define S3C_INT_BASE 0xE6784A00 -#define S3C_MEDIA_BASE 0xE6784B00 - -#define S3C_QOS_DCACHE_BASE 0xE6784BDC -#define S3C_QOS_CCI0_BASE 0xE6784C00 -#define S3C_QOS_CCI1_BASE 0xE6784C24 -#define S3C_QOS_MXI_BASE 0xE6784C48 -#define S3C_QOS_AXI_BASE 0xE6784C6C - -#define DBSC3_0_QOS_R0_BASE 0xE6791000 -#define DBSC3_0_QOS_R1_BASE 0xE6791100 -#define DBSC3_0_QOS_R2_BASE 0xE6791200 -#define DBSC3_0_QOS_R3_BASE 0xE6791300 -#define DBSC3_0_QOS_R4_BASE 0xE6791400 -#define DBSC3_0_QOS_R5_BASE 0xE6791500 -#define DBSC3_0_QOS_R6_BASE 0xE6791600 -#define DBSC3_0_QOS_R7_BASE 0xE6791700 -#define DBSC3_0_QOS_R8_BASE 0xE6791800 -#define DBSC3_0_QOS_R9_BASE 0xE6791900 -#define DBSC3_0_QOS_R10_BASE 0xE6791A00 -#define DBSC3_0_QOS_R11_BASE 0xE6791B00 -#define DBSC3_0_QOS_R12_BASE 0xE6791C00 -#define DBSC3_0_QOS_R13_BASE 0xE6791D00 -#define DBSC3_0_QOS_R14_BASE 0xE6791E00 -#define DBSC3_0_QOS_R15_BASE 0xE6791F00 -#define DBSC3_0_QOS_W0_BASE 0xE6792000 -#define DBSC3_0_QOS_W1_BASE 0xE6792100 -#define DBSC3_0_QOS_W2_BASE 0xE6792200 -#define DBSC3_0_QOS_W3_BASE 0xE6792300 -#define DBSC3_0_QOS_W4_BASE 0xE6792400 -#define DBSC3_0_QOS_W5_BASE 0xE6792500 -#define DBSC3_0_QOS_W6_BASE 0xE6792600 -#define DBSC3_0_QOS_W7_BASE 0xE6792700 -#define DBSC3_0_QOS_W8_BASE 0xE6792800 -#define DBSC3_0_QOS_W9_BASE 0xE6792900 -#define DBSC3_0_QOS_W10_BASE 0xE6792A00 -#define DBSC3_0_QOS_W11_BASE 0xE6792B00 -#define DBSC3_0_QOS_W12_BASE 0xE6792C00 -#define DBSC3_0_QOS_W13_BASE 0xE6792D00 -#define DBSC3_0_QOS_W14_BASE 0xE6792E00 -#define DBSC3_0_QOS_W15_BASE 0xE6792F00 - -#define DBSC3_0_DBADJ2 0xE67900C8 - -#define CCI_400_MAXOT_1 0xF0091110 -#define CCI_400_MAXOT_2 0xF0092110 -#define CCI_400_QOSCNTL_1 0xF009110C -#define CCI_400_QOSCNTL_2 0xF009210C - -#define MXI_BASE 0xFE960000 -#define MXI_QOS_BASE 0xFE960300 - -#define SYS_AXI_SYX64TO128_BASE 0xFF800300 -#define SYS_AXI_AVB_BASE 0xFF800340 -#define SYS_AXI_G2D_BASE 0xFF800540 -#define SYS_AXI_IMP0_BASE 0xFF800580 -#define SYS_AXI_IMP1_BASE 0xFF8005C0 -#define SYS_AXI_IMUX0_BASE 0xFF800600 -#define SYS_AXI_IMUX1_BASE 0xFF800640 -#define SYS_AXI_IMUX2_BASE 0xFF800680 -#define SYS_AXI_LBS_BASE 0xFF8006C0 -#define SYS_AXI_MMUDS_BASE 0xFF800700 -#define SYS_AXI_MMUM_BASE 0xFF800740 -#define SYS_AXI_MMUR_BASE 0xFF800780 -#define SYS_AXI_MMUS0_BASE 0xFF8007C0 -#define SYS_AXI_MMUS1_BASE 0xFF800800 -#define SYS_AXI_MTSB0_BASE 0xFF800880 -#define SYS_AXI_MTSB1_BASE 0xFF8008C0 -#define SYS_AXI_PCI_BASE 0xFF800900 -#define SYS_AXI_RTX_BASE 0xFF800940 -#define SYS_AXI_SDS0_BASE 0xFF800A80 -#define SYS_AXI_SDS1_BASE 0xFF800AC0 -#define SYS_AXI_USB20_BASE 0xFF800C00 -#define SYS_AXI_USB21_BASE 0xFF800C40 -#define SYS_AXI_USB22_BASE 0xFF800C80 -#define SYS_AXI_USB30_BASE 0xFF800CC0 - -#define RT_AXI_SHX_BASE 0xFF810100 -#define RT_AXI_RDS_BASE 0xFF8101C0 -#define RT_AXI_RTX64TO128_BASE 0xFF810200 -#define RT_AXI_STPRO_BASE 0xFF810240 - -#define MP_AXI_ADSP_BASE 0xFF820100 -#define MP_AXI_ASDS0_BASE 0xFF8201C0 -#define MP_AXI_ASDS1_BASE 0xFF820200 -#define MP_AXI_MLP_BASE 0xFF820240 -#define MP_AXI_MMUMP_BASE 0xFF820280 -#define MP_AXI_SPU_BASE 0xFF8202C0 -#define MP_AXI_SPUC_BASE 0xFF820300 - -#define SYS_AXI256_AXI128TO256_BASE 0xFF860100 -#define SYS_AXI256_SYX_BASE 0xFF860140 -#define SYS_AXI256_MPX_BASE 0xFF860180 -#define SYS_AXI256_MXI_BASE 0xFF8601C0 - -#define CCI_AXI_MMUS0_BASE 0xFF880100 -#define CCI_AXI_SYX2_BASE 0xFF880140 -#define CCI_AXI_MMUR_BASE 0xFF880180 -#define CCI_AXI_MMUDS_BASE 0xFF8801C0 -#define CCI_AXI_MMUM_BASE 0xFF880200 -#define CCI_AXI_MXI_BASE 0xFF880240 -#define CCI_AXI_MMUS1_BASE 0xFF880280 -#define CCI_AXI_MMUMP_BASE 0xFF8802C0 - -#define MEDIA_AXI_JPR_BASE 0xFE964100 -#define MEDIA_AXI_JPW_BASE 0xFE966100 -#define MEDIA_AXI_GCU0R_BASE 0xFE964140 -#define MEDIA_AXI_GCU0W_BASE 0xFE966140 -#define MEDIA_AXI_GCU1R_BASE 0xFE964180 -#define MEDIA_AXI_GCU1W_BASE 0xFE966180 -#define MEDIA_AXI_TDMR_BASE 0xFE964500 -#define MEDIA_AXI_TDMW_BASE 0xFE966500 -#define MEDIA_AXI_VSP0CR_BASE 0xFE964540 -#define MEDIA_AXI_VSP0CW_BASE 0xFE966540 -#define MEDIA_AXI_VSP1CR_BASE 0xFE964580 -#define MEDIA_AXI_VSP1CW_BASE 0xFE966580 -#define MEDIA_AXI_VSPDU0CR_BASE 0xFE9645C0 -#define MEDIA_AXI_VSPDU0CW_BASE 0xFE9665C0 -#define MEDIA_AXI_VSPDU1CR_BASE 0xFE964600 -#define MEDIA_AXI_VSPDU1CW_BASE 0xFE966600 -#define MEDIA_AXI_VIN0W_BASE 0xFE966900 -#define MEDIA_AXI_VSP0R_BASE 0xFE964D00 -#define MEDIA_AXI_VSP0W_BASE 0xFE966D00 -#define MEDIA_AXI_FDP0R_BASE 0xFE964D40 -#define MEDIA_AXI_FDP0W_BASE 0xFE966D40 -#define MEDIA_AXI_IMSR_BASE 0xFE964D80 -#define MEDIA_AXI_IMSW_BASE 0xFE966D80 -#define MEDIA_AXI_VSP1R_BASE 0xFE965100 -#define MEDIA_AXI_VSP1W_BASE 0xFE967100 -#define MEDIA_AXI_FDP1R_BASE 0xFE965140 -#define MEDIA_AXI_FDP1W_BASE 0xFE967140 -#define MEDIA_AXI_IMRR_BASE 0xFE965180 -#define MEDIA_AXI_IMRW_BASE 0xFE967180 -#define MEDIA_AXI_FDP2R_BASE 0xFE9651C0 -#define MEDIA_AXI_FDP2W_BASE 0xFE966DC0 -#define MEDIA_AXI_VSPD0R_BASE 0xFE965500 -#define MEDIA_AXI_VSPD0W_BASE 0xFE967500 -#define MEDIA_AXI_VSPD1R_BASE 0xFE965540 -#define MEDIA_AXI_VSPD1W_BASE 0xFE967540 -#define MEDIA_AXI_DU0R_BASE 0xFE965580 -#define MEDIA_AXI_DU0W_BASE 0xFE967580 -#define MEDIA_AXI_DU1R_BASE 0xFE9655C0 -#define MEDIA_AXI_DU1W_BASE 0xFE9675C0 -#define MEDIA_AXI_VCP0CR_BASE 0xFE965900 -#define MEDIA_AXI_VCP0CW_BASE 0xFE967900 -#define MEDIA_AXI_VCP0VR_BASE 0xFE965940 -#define MEDIA_AXI_VCP0VW_BASE 0xFE967940 -#define MEDIA_AXI_VPC0R_BASE 0xFE965980 -#define MEDIA_AXI_VCP1CR_BASE 0xFE965D00 -#define MEDIA_AXI_VCP1CW_BASE 0xFE967D00 -#define MEDIA_AXI_VCP1VR_BASE 0xFE965D40 -#define MEDIA_AXI_VCP1VW_BASE 0xFE967D40 -#define MEDIA_AXI_VPC1R_BASE 0xFE965D80 - -#define SYS_AXI_AVBDMSCR 0xFF802000 -#define SYS_AXI_SYX2DMSCR 0xFF802004 -#define SYS_AXI_CC50DMSCR 0xFF802008 -#define SYS_AXI_CC51DMSCR 0xFF80200C -#define SYS_AXI_CCIDMSCR 0xFF802010 -#define SYS_AXI_CSDMSCR 0xFF802014 -#define SYS_AXI_DDMDMSCR 0xFF802018 -#define SYS_AXI_ETHDMSCR 0xFF80201C -#define SYS_AXI_G2DDMSCR 0xFF802020 -#define SYS_AXI_IMP0DMSCR 0xFF802024 -#define SYS_AXI_IMP1DMSCR 0xFF802028 -#define SYS_AXI_LBSDMSCR 0xFF80202C -#define SYS_AXI_MMUDSDMSCR 0xFF802030 -#define SYS_AXI_MMUMXDMSCR 0xFF802034 -#define SYS_AXI_MMURDDMSCR 0xFF802038 -#define SYS_AXI_MMUS0DMSCR 0xFF80203C -#define SYS_AXI_MMUS1DMSCR 0xFF802040 -#define SYS_AXI_MPXDMSCR 0xFF802044 -#define SYS_AXI_MTSB0DMSCR 0xFF802048 -#define SYS_AXI_MTSB1DMSCR 0xFF80204C -#define SYS_AXI_PCIDMSCR 0xFF802050 -#define SYS_AXI_RTXDMSCR 0xFF802054 -#define SYS_AXI_SAT0DMSCR 0xFF802058 -#define SYS_AXI_SAT1DMSCR 0xFF80205C -#define SYS_AXI_SDM0DMSCR 0xFF802060 -#define SYS_AXI_SDM1DMSCR 0xFF802064 -#define SYS_AXI_SDS0DMSCR 0xFF802068 -#define SYS_AXI_SDS1DMSCR 0xFF80206C -#define SYS_AXI_ETRABDMSCR 0xFF802070 -#define SYS_AXI_ETRKFDMSCR 0xFF802074 -#define SYS_AXI_UDM0DMSCR 0xFF802078 -#define SYS_AXI_UDM1DMSCR 0xFF80207C -#define SYS_AXI_USB20DMSCR 0xFF802080 -#define SYS_AXI_USB21DMSCR 0xFF802084 -#define SYS_AXI_USB22DMSCR 0xFF802088 -#define SYS_AXI_USB30DMSCR 0xFF80208C -#define SYS_AXI_X128TO64SLVDMSCR 0xFF802100 -#define SYS_AXI_X64TO128SLVDMSCR 0xFF802104 -#define SYS_AXI_AVBSLVDMSCR 0xFF802108 -#define SYS_AXI_SYX2SLVDMSCR 0xFF80210C -#define SYS_AXI_ETHSLVDMSCR 0xFF802110 -#define SYS_AXI_GICSLVDMSCR 0xFF802114 -#define SYS_AXI_IMPSLVDMSCR 0xFF802118 -#define SYS_AXI_IMX0SLVDMSCR 0xFF80211C -#define SYS_AXI_IMX1SLVDMSCR 0xFF802120 -#define SYS_AXI_IMX2SLVDMSCR 0xFF802124 -#define SYS_AXI_LBSSLVDMSCR 0xFF802128 -#define SYS_AXI_MMC0SLVDMSCR 0xFF80212C -#define SYS_AXI_MMC1SLVDMSCR 0xFF802130 -#define SYS_AXI_MPXSLVDMSCR 0xFF802134 -#define SYS_AXI_MTSB0SLVDMSCR 0xFF802138 -#define SYS_AXI_MTSB1SLVDMSCR 0xFF80213C -#define SYS_AXI_MXTSLVDMSCR 0xFF802140 -#define SYS_AXI_PCISLVDMSCR 0xFF802144 -#define SYS_AXI_SYAPBSLVDMSCR 0xFF802148 -#define SYS_AXI_QSAPBSLVDMSCR 0xFF80214C -#define SYS_AXI_RTXSLVDMSCR 0xFF802150 -#define SYS_AXI_SAT0SLVDMSCR 0xFF802168 -#define SYS_AXI_SAT1SLVDMSCR 0xFF80216C -#define SYS_AXI_SDAP0SLVDMSCR 0xFF802170 -#define SYS_AXI_SDAP1SLVDMSCR 0xFF802174 -#define SYS_AXI_SDAP2SLVDMSCR 0xFF802178 -#define SYS_AXI_SDAP3SLVDMSCR 0xFF80217C -#define SYS_AXI_SGXSLVDMSCR 0xFF802180 -#define SYS_AXI_STBSLVDMSCR 0xFF802188 -#define SYS_AXI_STMSLVDMSCR 0xFF80218C -#define SYS_AXI_TSPL0SLVDMSCR 0xFF802194 -#define SYS_AXI_TSPL1SLVDMSCR 0xFF802198 -#define SYS_AXI_TSPL2SLVDMSCR 0xFF80219C -#define SYS_AXI_USB20SLVDMSCR 0xFF8021A0 -#define SYS_AXI_USB21SLVDMSCR 0xFF8021A4 -#define SYS_AXI_USB22SLVDMSCR 0xFF8021A8 -#define SYS_AXI_USB30SLVDMSCR 0xFF8021AC - -#define RT_AXI_CBMDMSCR 0xFF812000 -#define RT_AXI_DBDMSCR 0xFF812004 -#define RT_AXI_RDMDMSCR 0xFF812008 -#define RT_AXI_RDSDMSCR 0xFF81200C -#define RT_AXI_STRDMSCR 0xFF812010 -#define RT_AXI_SY2RTDMSCR 0xFF812014 -#define RT_AXI_CBSSLVDMSCR 0xFF812100 -#define RT_AXI_DBSSLVDMSCR 0xFF812104 -#define RT_AXI_RTAP1SLVDMSCR 0xFF812108 -#define RT_AXI_RTAP2SLVDMSCR 0xFF81210C -#define RT_AXI_RTAP3SLVDMSCR 0xFF812110 -#define RT_AXI_RT2SYSLVDMSCR 0xFF812114 -#define RT_AXI_A128TO64SLVDMSCR 0xFF812118 -#define RT_AXI_A64TO128SLVDMSCR 0xFF81211C -#define RT_AXI_A64TO128CSLVDMSCR 0xFF812120 -#define RT_AXI_UTLBRSLVDMSCR 0xFF812128 - -#define MP_AXI_ADSPDMSCR 0xFF822000 -#define MP_AXI_ASDM0DMSCR 0xFF822004 -#define MP_AXI_ASDM1DMSCR 0xFF822008 -#define MP_AXI_ASDS0DMSCR 0xFF82200C -#define MP_AXI_ASDS1DMSCR 0xFF822010 -#define MP_AXI_MLPDMSCR 0xFF822014 -#define MP_AXI_MMUMPDMSCR 0xFF822018 -#define MP_AXI_SPUDMSCR 0xFF82201C -#define MP_AXI_SPUCDMSCR 0xFF822020 -#define MP_AXI_SY2MPDMSCR 0xFF822024 -#define MP_AXI_ADSPSLVDMSCR 0xFF822100 -#define MP_AXI_MLMSLVDMSCR 0xFF822104 -#define MP_AXI_MPAP4SLVDMSCR 0xFF822108 -#define MP_AXI_MPAP5SLVDMSCR 0xFF82210C -#define MP_AXI_MPAP6SLVDMSCR 0xFF822110 -#define MP_AXI_MPAP7SLVDMSCR 0xFF822114 -#define MP_AXI_MP2SYSLVDMSCR 0xFF822118 -#define MP_AXI_MP2SY2SLVDMSCR 0xFF82211C -#define MP_AXI_MPXAPSLVDMSCR 0xFF822124 -#define MP_AXI_SPUSLVDMSCR 0xFF822128 -#define MP_AXI_UTLBMPSLVDMSCR 0xFF82212C - -#define ADM_AXI_ASDM0DMSCR 0xFF842000 -#define ADM_AXI_ASDM1DMSCR 0xFF842004 -#define ADM_AXI_MPAP1SLVDMSCR 0xFF842104 -#define ADM_AXI_MPAP2SLVDMSCR 0xFF842108 -#define ADM_AXI_MPAP3SLVDMSCR 0xFF84210C - -#define DM_AXI_RDMDMSCR 0xFF852000 -#define DM_AXI_SDM0DMSCR 0xFF852004 -#define DM_AXI_SDM1DMSCR 0xFF852008 -#define DM_AXI_MMAP0SLVDMSCR 0xFF852100 -#define DM_AXI_MMAP1SLVDMSCR 0xFF852104 -#define DM_AXI_QSPAPSLVDMSCR 0xFF852108 -#define DM_AXI_RAP4SLVDMSCR 0xFF85210C -#define DM_AXI_RAP5SLVDMSCR 0xFF852110 -#define DM_AXI_SAP4SLVDMSCR 0xFF852114 -#define DM_AXI_SAP5SLVDMSCR 0xFF852118 -#define DM_AXI_SAP6SLVDMSCR 0xFF85211C -#define DM_AXI_SAP65SLVDMSCR 0xFF852120 -#define DM_AXI_SDAP0SLVDMSCR 0xFF852124 -#define DM_AXI_SDAP1SLVDMSCR 0xFF852128 -#define DM_AXI_SDAP2SLVDMSCR 0xFF85212C -#define DM_AXI_SDAP3SLVDMSCR 0xFF852130 - -#define SYS_AXI256_SYXDMSCR 0xFF862000 -#define SYS_AXI256_MPXDMSCR 0xFF862004 -#define SYS_AXI256_MXIDMSCR 0xFF862008 -#define SYS_AXI256_X128TO256SLVDMSCR 0xFF862100 -#define SYS_AXI256_X256TO128SLVDMSCR 0xFF862104 -#define SYS_AXI256_SYXSLVDMSCR 0xFF862108 -#define SYS_AXI256_CCXSLVDMSCR 0xFF86210C -#define SYS_AXI256_S3CSLVDMSCR 0xFF862110 - -#define MXT_SYXDMSCR 0xFF872000 -#define MXT_CMM0SLVDMSCR 0xFF872100 -#define MXT_CMM1SLVDMSCR 0xFF872104 -#define MXT_CMM2SLVDMSCR 0xFF872108 -#define MXT_FDPSLVDMSCR 0xFF87210C -#define MXT_IMRSLVDMSCR 0xFF872110 -#define MXT_VINSLVDMSCR 0xFF872114 -#define MXT_VPC0SLVDMSCR 0xFF872118 -#define MXT_VPC1SLVDMSCR 0xFF87211C -#define MXT_VSP0SLVDMSCR 0xFF872120 -#define MXT_VSP1SLVDMSCR 0xFF872124 -#define MXT_VSPD0SLVDMSCR 0xFF872128 -#define MXT_VSPD1SLVDMSCR 0xFF87212C -#define MXT_MAP1SLVDMSCR 0xFF872130 -#define MXT_MAP2SLVDMSCR 0xFF872134 - -#define CCI_AXI_MMUS0DMSCR 0xFF882000 -#define CCI_AXI_SYX2DMSCR 0xFF882004 -#define CCI_AXI_MMURDMSCR 0xFF882008 -#define CCI_AXI_MMUDSDMSCR 0xFF88200C -#define CCI_AXI_MMUMDMSCR 0xFF882010 -#define CCI_AXI_MXIDMSCR 0xFF882014 -#define CCI_AXI_MMUS1DMSCR 0xFF882018 -#define CCI_AXI_MMUMPDMSCR 0xFF88201C -#define CCI_AXI_DVMDMSCR 0xFF882020 -#define CCI_AXI_CCISLVDMSCR 0xFF882100 - -#define CCI_AXI_IPMMUIDVMCR 0xFF880400 -#define CCI_AXI_IPMMURDVMCR 0xFF880404 -#define CCI_AXI_IPMMUS0DVMCR 0xFF880408 -#define CCI_AXI_IPMMUS1DVMCR 0xFF88040C -#define CCI_AXI_IPMMUMPDVMCR 0xFF880410 -#define CCI_AXI_IPMMUDSDVMCR 0xFF880414 -#define CCI_AXI_AX2ADDRMASK 0xFF88041C - -#ifndef __ASSEMBLY__ -#include <asm/types.h> - -/* RWDT */ -struct r8a7790_rwdt { - u32 rwtcnt; /* 0x00 */ - u32 rwtcsra; /* 0x04 */ - u16 rwtcsrb; /* 0x08 */ -}; - -/* SWDT */ -struct r8a7790_swdt { - u32 swtcnt; /* 0x00 */ - u32 swtcsra; /* 0x04 */ - u16 swtcsrb; /* 0x08 */ -}; - -/* LBSC */ -struct r8a7790_lbsc { - u32 cs0ctrl; - u32 cs1ctrl; - u32 ecs0ctrl; - u32 ecs1ctrl; - u32 ecs2ctrl; - u32 ecs3ctrl; - u32 ecs4ctrl; - u32 ecs5ctrl; - u32 dummy0[4]; /* 0x20 .. 0x2C */ - u32 cswcr0; - u32 cswcr1; - u32 ecswcr0; - u32 ecswcr1; - u32 ecswcr2; - u32 ecswcr3; - u32 ecswcr4; - u32 ecswcr5; - u32 exdmawcr0; - u32 exdmawcr1; - u32 exdmawcr2; - u32 dummy1[9]; /* 0x5C .. 0x7C */ - u32 cspwcr0; - u32 cspwcr1; - u32 ecspwcr0; - u32 ecspwcr1; - u32 ecspwcr2; - u32 ecspwcr3; - u32 ecspwcr4; - u32 ecspwcr5; - u32 exwtsync; - u32 dummy2[3]; /* 0xA4 .. 0xAC */ - u32 cs0bstctl; - u32 cs0btph; - u32 dummy3[2]; /* 0xB8 .. 0xBC */ - u32 cs1gdst; - u32 ecs0gdst; - u32 ecs1gdst; - u32 ecs2gdst; - u32 ecs3gdst; - u32 ecs4gdst; - u32 ecs5gdst; - u32 dummy4[5]; /* 0xDC .. 0xEC */ - u32 exdmaset0; - u32 exdmaset1; - u32 exdmaset2; - u32 dummy5[5]; /* 0xFC .. 0x10C */ - u32 exdmcr0; - u32 exdmcr1; - u32 exdmcr2; - u32 dummy6[5]; /* 0x11C .. 0x12C */ - u32 bcintsr; - u32 bcintcr; - u32 bcintmr; - u32 dummy7; /* 0x13C */ - u32 exbatlv; - u32 exwtsts; - u32 dummy8[14]; /* 0x148 .. 0x17C */ - u32 atacsctrl; - u32 dummy9[15]; /* 0x184 .. 0x1BC */ - u32 exbct; - u32 extct; -}; - -/* DBSC3 */ -struct r8a7790_dbsc3 { - u32 dummy0[3]; /* 0x00 .. 0x08 */ - u32 dbstate1; - u32 dbacen; - u32 dbrfen; - u32 dbcmd; - u32 dbwait; - u32 dbkind; - u32 dbconf0; - u32 dummy1[2]; /* 0x28 .. 0x2C */ - u32 dbphytype; - u32 dummy2[3]; /* 0x34 .. 0x3C */ - u32 dbtr0; - u32 dbtr1; - u32 dbtr2; - u32 dummy3; /* 0x4C */ - u32 dbtr3; - u32 dbtr4; - u32 dbtr5; - u32 dbtr6; - u32 dbtr7; - u32 dbtr8; - u32 dbtr9; - u32 dbtr10; - u32 dbtr11; - u32 dbtr12; - u32 dbtr13; - u32 dbtr14; - u32 dbtr15; - u32 dbtr16; - u32 dbtr17; - u32 dbtr18; - u32 dbtr19; - u32 dummy4[7]; /* 0x94 .. 0xAC */ - u32 dbbl; - u32 dummy5[3]; /* 0xB4 .. 0xBC */ - u32 dbadj0; - u32 dummy6; /* 0xC4 */ - u32 dbadj2; - u32 dummy7[5]; /* 0xCC .. 0xDC */ - u32 dbrfcnf0; - u32 dbrfcnf1; - u32 dbrfcnf2; - u32 dummy8[2]; /* 0xEC .. 0xF0 */ - u32 dbcalcnf; - u32 dbcaltr; - u32 dummy9; /* 0xFC */ - u32 dbrnk0; - u32 dummy10[31]; /* 0x104 .. 0x17C */ - u32 dbpdncnf; - u32 dummy11[47]; /* 0x184 ..0x23C */ - u32 dbdfistat; - u32 dbdficnt; - u32 dummy12[14]; /* 0x248 .. 0x27C */ - u32 dbpdlck; - u32 dummy13[3]; /* 0x284 .. 0x28C */ - u32 dbpdrga; - u32 dummy14[3]; /* 0x294 .. 0x29C */ - u32 dbpdrgd; - u32 dummy15[24]; /* 0x2A4 .. 0x300 */ - u32 dbbs0cnt1; - u32 dummy16[30]; /* 0x308 .. 0x37C */ - u32 dbwt0cnf0; - u32 dbwt0cnf1; - u32 dbwt0cnf2; - u32 dbwt0cnf3; - u32 dbwt0cnf4; -}; - -/* GPIO */ -struct r8a7790_gpio { - u32 iointsel; - u32 inoutsel; - u32 outdt; - u32 indt; - u32 intdt; - u32 intclr; - u32 intmsk; - u32 posneg; - u32 edglevel; - u32 filonoff; - u32 intmsks; - u32 mskclrs; - u32 outdtsel; - u32 outdth; - u32 outdtl; - u32 bothedge; -}; - -/* S3C(QoS) */ -struct r8a7790_s3c { - u32 s3cexcladdmsk; - u32 s3cexclidmsk; - u32 s3cadsplcr; - u32 s3cmaar; - u32 s3carcr11; - u32 s3crorr; - u32 s3cworr; - u32 s3carcr22; - u32 dummy1[2]; /* 0x20 .. 0x24 */ - u32 s3cmctr; - u32 dummy2; /* 0x2C */ - u32 cconf0; - u32 cconf1; - u32 cconf2; - u32 cconf3; -}; - -struct r8a7790_s3c_qos { - u32 s3cqos0; - u32 s3cqos1; - u32 s3cqos2; - u32 s3cqos3; - u32 s3cqos4; - u32 s3cqos5; - u32 s3cqos6; - u32 s3cqos7; - u32 s3cqos8; -}; - -/* DBSC(QoS) */ -struct r8a7790_dbsc3_qos { - u32 dblgcnt; - u32 dbtmval0; - u32 dbtmval1; - u32 dbtmval2; - u32 dbtmval3; - u32 dbrqctr; - u32 dbthres0; - u32 dbthres1; - u32 dbthres2; - u32 dummy0; /* 0x24 */ - u32 dblgqon; -}; - -/* MXI(QoS) */ -struct r8a7790_mxi { - u32 mxsaar0; - u32 mxsaar1; - u32 dummy0[7]; /* 0x08 .. 0x20 */ - u32 mxaxiracr; - u32 mxs3cracr; - u32 dummy1[2]; /* 0x2C .. 0x30 */ - u32 mxaxiwacr; - u32 mxs3cwacr; - u32 dummy2; /* 0x3C */ - u32 mxrtcr; - u32 mxwtcr; -}; - -struct r8a7790_mxi_qos { - u32 vspdu0; - u32 vspdu1; - u32 du0; - u32 du1; -}; - -/* AXI(QoS) */ -struct r8a7790_axi_qos { - u32 qosconf; - u32 qosctset0; - u32 qosctset1; - u32 qosctset2; - u32 qosctset3; - u32 qosreqctr; - u32 qosthres0; - u32 qosthres1; - u32 qosthres2; - u32 qosqon; -}; +#include "rcar-base.h" -#endif +#define R8A7790_CUT_ES2X 2 +#define IS_R8A7790_ES2() \ + (rmobile_get_cpu_rev_integer() == R8A7790_CUT_ES2X) #endif /* __ASM_ARCH_R8A7790_H */ diff --git a/arch/arm/include/asm/arch-rmobile/r8a7791.h b/arch/arm/include/asm/arch-rmobile/r8a7791.h index ff30180591..479182571e 100644 --- a/arch/arm/include/asm/arch-rmobile/r8a7791.h +++ b/arch/arm/include/asm/arch-rmobile/r8a7791.h @@ -1,69 +1,18 @@ /* * arch/arm/include/asm/arch-rmobile/r8a7791.h * - * Copyright (C) 2013 Renesas Electronics Corporation + * Copyright (C) 2013,2014 Renesas Electronics Corporation * * SPDX-License-Identifier: GPL-2.0 - */ +*/ #ifndef __ASM_ARCH_R8A7791_H #define __ASM_ARCH_R8A7791_H +#include "rcar-base.h" /* - * R8A7791 I/O Addresses + * R-Car (R8A7791) I/O Addresses */ -#define RWDT_BASE 0xE6020000 -#define SWDT_BASE 0xE6030000 -#define LBSC_BASE 0xFEC00200 -#define DBSC3_0_BASE 0xE6790000 -#define DBSC3_1_BASE 0xE67A0000 -#define TMU_BASE 0xE61E0000 -#define GPIO5_BASE 0xE6055000 -#define SH_QSPI_BASE 0xE6B10000 - -#define S3C_BASE 0xE6784000 -#define S3C_INT_BASE 0xE6784A00 -#define S3C_MEDIA_BASE 0xE6784B00 - -#define S3C_QOS_DCACHE_BASE 0xE6784BDC -#define S3C_QOS_CCI0_BASE 0xE6784C00 -#define S3C_QOS_CCI1_BASE 0xE6784C24 -#define S3C_QOS_MXI_BASE 0xE6784C48 -#define S3C_QOS_AXI_BASE 0xE6784C6C - -#define DBSC3_0_QOS_R0_BASE 0xE6791000 -#define DBSC3_0_QOS_R1_BASE 0xE6791100 -#define DBSC3_0_QOS_R2_BASE 0xE6791200 -#define DBSC3_0_QOS_R3_BASE 0xE6791300 -#define DBSC3_0_QOS_R4_BASE 0xE6791400 -#define DBSC3_0_QOS_R5_BASE 0xE6791500 -#define DBSC3_0_QOS_R6_BASE 0xE6791600 -#define DBSC3_0_QOS_R7_BASE 0xE6791700 -#define DBSC3_0_QOS_R8_BASE 0xE6791800 -#define DBSC3_0_QOS_R9_BASE 0xE6791900 -#define DBSC3_0_QOS_R10_BASE 0xE6791A00 -#define DBSC3_0_QOS_R11_BASE 0xE6791B00 -#define DBSC3_0_QOS_R12_BASE 0xE6791C00 -#define DBSC3_0_QOS_R13_BASE 0xE6791D00 -#define DBSC3_0_QOS_R14_BASE 0xE6791E00 -#define DBSC3_0_QOS_R15_BASE 0xE6791F00 -#define DBSC3_0_QOS_W0_BASE 0xE6792000 -#define DBSC3_0_QOS_W1_BASE 0xE6792100 -#define DBSC3_0_QOS_W2_BASE 0xE6792200 -#define DBSC3_0_QOS_W3_BASE 0xE6792300 -#define DBSC3_0_QOS_W4_BASE 0xE6792400 -#define DBSC3_0_QOS_W5_BASE 0xE6792500 -#define DBSC3_0_QOS_W6_BASE 0xE6792600 -#define DBSC3_0_QOS_W7_BASE 0xE6792700 -#define DBSC3_0_QOS_W8_BASE 0xE6792800 -#define DBSC3_0_QOS_W9_BASE 0xE6792900 -#define DBSC3_0_QOS_W10_BASE 0xE6792A00 -#define DBSC3_0_QOS_W11_BASE 0xE6792B00 -#define DBSC3_0_QOS_W12_BASE 0xE6792C00 -#define DBSC3_0_QOS_W13_BASE 0xE6792D00 -#define DBSC3_0_QOS_W14_BASE 0xE6792E00 -#define DBSC3_0_QOS_W15_BASE 0xE6792F00 - #define DBSC3_1_QOS_R0_BASE 0xE67A1000 #define DBSC3_1_QOS_R1_BASE 0xE67A1100 #define DBSC3_1_QOS_R2_BASE 0xE67A1200 @@ -97,569 +46,8 @@ #define DBSC3_1_QOS_W14_BASE 0xE67A2E00 #define DBSC3_1_QOS_W15_BASE 0xE67A2F00 -#define DBSC3_0_DBADJ2 0xE67900C8 - -#define CCI_400_MAXOT_1 0xF0091110 -#define CCI_400_MAXOT_2 0xF0092110 -#define CCI_400_QOSCNTL_1 0xF009110C -#define CCI_400_QOSCNTL_2 0xF009210C - -#define MXI_BASE 0xFE960000 -#define MXI_QOS_BASE 0xFE960300 - -#define SYS_AXI_SYX64TO128_BASE 0xFF800300 -#define SYS_AXI_AVB_BASE 0xFF800340 -#define SYS_AXI_G2D_BASE 0xFF800540 -#define SYS_AXI_IMP0_BASE 0xFF800580 -#define SYS_AXI_IMP1_BASE 0xFF8005C0 -#define SYS_AXI_IMUX0_BASE 0xFF800600 -#define SYS_AXI_IMUX1_BASE 0xFF800640 -#define SYS_AXI_IMUX2_BASE 0xFF800680 -#define SYS_AXI_LBS_BASE 0xFF8006C0 -#define SYS_AXI_MMUDS_BASE 0xFF800700 -#define SYS_AXI_MMUM_BASE 0xFF800740 -#define SYS_AXI_MMUR_BASE 0xFF800780 -#define SYS_AXI_MMUS0_BASE 0xFF8007C0 -#define SYS_AXI_MMUS1_BASE 0xFF800800 -#define SYS_AXI_MTSB0_BASE 0xFF800880 -#define SYS_AXI_MTSB1_BASE 0xFF8008C0 -#define SYS_AXI_PCI_BASE 0xFF800900 -#define SYS_AXI_RTX_BASE 0xFF800940 -#define SYS_AXI_SDS0_BASE 0xFF800A80 -#define SYS_AXI_SDS1_BASE 0xFF800AC0 -#define SYS_AXI_USB20_BASE 0xFF800C00 -#define SYS_AXI_USB21_BASE 0xFF800C40 -#define SYS_AXI_USB22_BASE 0xFF800C80 -#define SYS_AXI_USB30_BASE 0xFF800CC0 -#define SYS_AXI_AX2M_BASE 0xFF800380 -#define SYS_AXI_CC50_BASE 0xFF8003C0 -#define SYS_AXI_CCI_BASE 0xFF800440 -#define SYS_AXI_CS_BASE 0xFF800480 -#define SYS_AXI_DDM_BASE 0xFF8004C0 -#define SYS_AXI_ETH_BASE 0xFF800500 -#define SYS_AXI_MPXM_BASE 0xFF800840 -#define SYS_AXI_SAT0_BASE 0xFF800980 -#define SYS_AXI_SAT1_BASE 0xFF8009C0 -#define SYS_AXI_SDM0_BASE 0xFF800A00 -#define SYS_AXI_SDM1_BASE 0xFF800A40 -#define SYS_AXI_TRAB_BASE 0xFF800B00 -#define SYS_AXI_UDM0_BASE 0xFF800B80 -#define SYS_AXI_UDM1_BASE 0xFF800BC0 - -#define RT_AXI_SHX_BASE 0xFF810100 -#define RT_AXI_DBG_BASE 0xFF810140 -#define RT_AXI_RDM_BASE 0xFF810180 -#define RT_AXI_RDS_BASE 0xFF8101C0 -#define RT_AXI_RTX64TO128_BASE 0xFF810200 -#define RT_AXI_STPRO_BASE 0xFF810240 -#define RT_AXI_SY2RT_BASE 0xFF810280 - -#define MP_AXI_ADSP_BASE 0xFF820100 -#define MP_AXI_ASDS0_BASE 0xFF8201C0 -#define MP_AXI_ASDS1_BASE 0xFF820200 -#define MP_AXI_MLP_BASE 0xFF820240 -#define MP_AXI_MMUMP_BASE 0xFF820280 -#define MP_AXI_SPU_BASE 0xFF8202C0 -#define MP_AXI_SPUC_BASE 0xFF820300 - -#define SYS_AXI256_AXI128TO256_BASE 0xFF860100 -#define SYS_AXI256_SYX_BASE 0xFF860140 -#define SYS_AXI256_MPX_BASE 0xFF860180 -#define SYS_AXI256_MXI_BASE 0xFF8601C0 - -#define CCI_AXI_MMUS0_BASE 0xFF880100 -#define CCI_AXI_SYX2_BASE 0xFF880140 -#define CCI_AXI_MMUR_BASE 0xFF880180 -#define CCI_AXI_MMUDS_BASE 0xFF8801C0 -#define CCI_AXI_MMUM_BASE 0xFF880200 -#define CCI_AXI_MXI_BASE 0xFF880240 -#define CCI_AXI_MMUS1_BASE 0xFF880280 -#define CCI_AXI_MMUMP_BASE 0xFF8802C0 - -#define MEDIA_AXI_MXR_BASE 0xFE960080 -#define MEDIA_AXI_MXW_BASE 0xFE9600C0 -#define MEDIA_AXI_JPR_BASE 0xFE964100 -#define MEDIA_AXI_JPW_BASE 0xFE966100 -#define MEDIA_AXI_GCU0R_BASE 0xFE964140 -#define MEDIA_AXI_GCU0W_BASE 0xFE966140 -#define MEDIA_AXI_GCU1R_BASE 0xFE964180 -#define MEDIA_AXI_GCU1W_BASE 0xFE966180 -#define MEDIA_AXI_TDMR_BASE 0xFE964500 -#define MEDIA_AXI_TDMW_BASE 0xFE966500 -#define MEDIA_AXI_VSP0CR_BASE 0xFE964540 -#define MEDIA_AXI_VSP0CW_BASE 0xFE966540 -#define MEDIA_AXI_VSP1CR_BASE 0xFE964580 -#define MEDIA_AXI_VSP1CW_BASE 0xFE966580 -#define MEDIA_AXI_VSPDU0CR_BASE 0xFE9645C0 -#define MEDIA_AXI_VSPDU0CW_BASE 0xFE9665C0 -#define MEDIA_AXI_VSPDU1CR_BASE 0xFE964600 -#define MEDIA_AXI_VSPDU1CW_BASE 0xFE966600 -#define MEDIA_AXI_VIN0W_BASE 0xFE966900 -#define MEDIA_AXI_VSP0R_BASE 0xFE964D00 -#define MEDIA_AXI_VSP0W_BASE 0xFE966D00 -#define MEDIA_AXI_FDP0R_BASE 0xFE964D40 -#define MEDIA_AXI_FDP0W_BASE 0xFE966D40 -#define MEDIA_AXI_IMSR_BASE 0xFE964D80 -#define MEDIA_AXI_IMSW_BASE 0xFE966D80 -#define MEDIA_AXI_VSP1R_BASE 0xFE965100 -#define MEDIA_AXI_VSP1W_BASE 0xFE967100 -#define MEDIA_AXI_FDP1R_BASE 0xFE965140 -#define MEDIA_AXI_FDP1W_BASE 0xFE967140 -#define MEDIA_AXI_IMRR_BASE 0xFE965180 -#define MEDIA_AXI_IMRW_BASE 0xFE967180 -#define MEDIA_AXI_FDP2R_BASE 0xFE9651C0 -#define MEDIA_AXI_FDP2W_BASE 0xFE966DC0 -#define MEDIA_AXI_VSPD0R_BASE 0xFE965500 -#define MEDIA_AXI_VSPD0W_BASE 0xFE967500 -#define MEDIA_AXI_VSPD1R_BASE 0xFE965540 -#define MEDIA_AXI_VSPD1W_BASE 0xFE967540 -#define MEDIA_AXI_DU0R_BASE 0xFE965580 -#define MEDIA_AXI_DU0W_BASE 0xFE967580 -#define MEDIA_AXI_DU1R_BASE 0xFE9655C0 -#define MEDIA_AXI_DU1W_BASE 0xFE9675C0 -#define MEDIA_AXI_VCP0CR_BASE 0xFE965900 -#define MEDIA_AXI_VCP0CW_BASE 0xFE967900 -#define MEDIA_AXI_VCP0VR_BASE 0xFE965940 -#define MEDIA_AXI_VCP0VW_BASE 0xFE967940 -#define MEDIA_AXI_VPC0R_BASE 0xFE965980 -#define MEDIA_AXI_VCP1CR_BASE 0xFE965D00 -#define MEDIA_AXI_VCP1CW_BASE 0xFE967D00 -#define MEDIA_AXI_VCP1VR_BASE 0xFE965D40 -#define MEDIA_AXI_VCP1VW_BASE 0xFE967D40 -#define MEDIA_AXI_VPC1R_BASE 0xFE965D80 - -#define SYS_AXI_AVBDMSCR 0xFF802000 -#define SYS_AXI_SYX2DMSCR 0xFF802004 -#define SYS_AXI_CC50DMSCR 0xFF802008 -#define SYS_AXI_CC51DMSCR 0xFF80200C -#define SYS_AXI_CCIDMSCR 0xFF802010 -#define SYS_AXI_CSDMSCR 0xFF802014 -#define SYS_AXI_DDMDMSCR 0xFF802018 -#define SYS_AXI_ETHDMSCR 0xFF80201C -#define SYS_AXI_G2DDMSCR 0xFF802020 -#define SYS_AXI_IMP0DMSCR 0xFF802024 -#define SYS_AXI_IMP1DMSCR 0xFF802028 -#define SYS_AXI_LBSDMSCR 0xFF80202C -#define SYS_AXI_MMUDSDMSCR 0xFF802030 -#define SYS_AXI_MMUMXDMSCR 0xFF802034 -#define SYS_AXI_MMURDDMSCR 0xFF802038 -#define SYS_AXI_MMUS0DMSCR 0xFF80203C -#define SYS_AXI_MMUS1DMSCR 0xFF802040 -#define SYS_AXI_MPXDMSCR 0xFF802044 -#define SYS_AXI_MTSB0DMSCR 0xFF802048 -#define SYS_AXI_MTSB1DMSCR 0xFF80204C -#define SYS_AXI_PCIDMSCR 0xFF802050 -#define SYS_AXI_RTXDMSCR 0xFF802054 -#define SYS_AXI_SAT0DMSCR 0xFF802058 -#define SYS_AXI_SAT1DMSCR 0xFF80205C -#define SYS_AXI_SDM0DMSCR 0xFF802060 -#define SYS_AXI_SDM1DMSCR 0xFF802064 -#define SYS_AXI_SDS0DMSCR 0xFF802068 -#define SYS_AXI_SDS1DMSCR 0xFF80206C -#define SYS_AXI_ETRABDMSCR 0xFF802070 -#define SYS_AXI_ETRKFDMSCR 0xFF802074 -#define SYS_AXI_UDM0DMSCR 0xFF802078 -#define SYS_AXI_UDM1DMSCR 0xFF80207C -#define SYS_AXI_USB20DMSCR 0xFF802080 -#define SYS_AXI_USB21DMSCR 0xFF802084 -#define SYS_AXI_USB22DMSCR 0xFF802088 -#define SYS_AXI_USB30DMSCR 0xFF80208C -#define SYS_AXI_X128TO64SLVDMSCR 0xFF802100 -#define SYS_AXI_X64TO128SLVDMSCR 0xFF802104 -#define SYS_AXI_AVBSLVDMSCR 0xFF802108 -#define SYS_AXI_SYX2SLVDMSCR 0xFF80210C -#define SYS_AXI_ETHSLVDMSCR 0xFF802110 -#define SYS_AXI_GICSLVDMSCR 0xFF802114 -#define SYS_AXI_IMPSLVDMSCR 0xFF802118 -#define SYS_AXI_IMX0SLVDMSCR 0xFF80211C -#define SYS_AXI_IMX1SLVDMSCR 0xFF802120 -#define SYS_AXI_IMX2SLVDMSCR 0xFF802124 -#define SYS_AXI_LBSSLVDMSCR 0xFF802128 -#define SYS_AXI_MMC0SLVDMSCR 0xFF80212C -#define SYS_AXI_MMC1SLVDMSCR 0xFF802130 -#define SYS_AXI_MPXSLVDMSCR 0xFF802134 -#define SYS_AXI_MTSB0SLVDMSCR 0xFF802138 -#define SYS_AXI_MTSB1SLVDMSCR 0xFF80213C -#define SYS_AXI_MXTSLVDMSCR 0xFF802140 -#define SYS_AXI_PCISLVDMSCR 0xFF802144 -#define SYS_AXI_SYAPBSLVDMSCR 0xFF802148 -#define SYS_AXI_QSAPBSLVDMSCR 0xFF80214C -#define SYS_AXI_RTXSLVDMSCR 0xFF802150 -#define SYS_AXI_SAT0SLVDMSCR 0xFF802168 -#define SYS_AXI_SAT1SLVDMSCR 0xFF80216C -#define SYS_AXI_SDAP0SLVDMSCR 0xFF802170 -#define SYS_AXI_SDAP1SLVDMSCR 0xFF802174 -#define SYS_AXI_SDAP2SLVDMSCR 0xFF802178 -#define SYS_AXI_SDAP3SLVDMSCR 0xFF80217C -#define SYS_AXI_SGXSLVDMSCR 0xFF802180 -#define SYS_AXI_STBSLVDMSCR 0xFF802188 -#define SYS_AXI_STMSLVDMSCR 0xFF80218C -#define SYS_AXI_TSPL0SLVDMSCR 0xFF802194 -#define SYS_AXI_TSPL1SLVDMSCR 0xFF802198 -#define SYS_AXI_TSPL2SLVDMSCR 0xFF80219C -#define SYS_AXI_USB20SLVDMSCR 0xFF8021A0 -#define SYS_AXI_USB21SLVDMSCR 0xFF8021A4 -#define SYS_AXI_USB22SLVDMSCR 0xFF8021A8 -#define SYS_AXI_USB30SLVDMSCR 0xFF8021AC - -#define RT_AXI_CBMDMSCR 0xFF812000 -#define RT_AXI_DBDMSCR 0xFF812004 -#define RT_AXI_RDMDMSCR 0xFF812008 -#define RT_AXI_RDSDMSCR 0xFF81200C -#define RT_AXI_STRDMSCR 0xFF812010 -#define RT_AXI_SY2RTDMSCR 0xFF812014 -#define RT_AXI_CBSSLVDMSCR 0xFF812100 -#define RT_AXI_DBSSLVDMSCR 0xFF812104 -#define RT_AXI_RTAP1SLVDMSCR 0xFF812108 -#define RT_AXI_RTAP2SLVDMSCR 0xFF81210C -#define RT_AXI_RTAP3SLVDMSCR 0xFF812110 -#define RT_AXI_RT2SYSLVDMSCR 0xFF812114 -#define RT_AXI_A128TO64SLVDMSCR 0xFF812118 -#define RT_AXI_A64TO128SLVDMSCR 0xFF81211C -#define RT_AXI_A64TO128CSLVDMSCR 0xFF812120 -#define RT_AXI_UTLBRSLVDMSCR 0xFF812128 - -#define MP_AXI_ADSPDMSCR 0xFF822000 -#define MP_AXI_ASDM0DMSCR 0xFF822004 -#define MP_AXI_ASDM1DMSCR 0xFF822008 -#define MP_AXI_ASDS0DMSCR 0xFF82200C -#define MP_AXI_ASDS1DMSCR 0xFF822010 -#define MP_AXI_MLPDMSCR 0xFF822014 -#define MP_AXI_MMUMPDMSCR 0xFF822018 -#define MP_AXI_SPUDMSCR 0xFF82201C -#define MP_AXI_SPUCDMSCR 0xFF822020 -#define MP_AXI_SY2MPDMSCR 0xFF822024 -#define MP_AXI_ADSPSLVDMSCR 0xFF822100 -#define MP_AXI_MLMSLVDMSCR 0xFF822104 -#define MP_AXI_MPAP4SLVDMSCR 0xFF822108 -#define MP_AXI_MPAP5SLVDMSCR 0xFF82210C -#define MP_AXI_MPAP6SLVDMSCR 0xFF822110 -#define MP_AXI_MPAP7SLVDMSCR 0xFF822114 -#define MP_AXI_MP2SYSLVDMSCR 0xFF822118 -#define MP_AXI_MP2SY2SLVDMSCR 0xFF82211C -#define MP_AXI_MPXAPSLVDMSCR 0xFF822124 -#define MP_AXI_SPUSLVDMSCR 0xFF822128 -#define MP_AXI_UTLBMPSLVDMSCR 0xFF82212C - -#define ADM_AXI_ASDM0DMSCR 0xFF842000 -#define ADM_AXI_ASDM1DMSCR 0xFF842004 -#define ADM_AXI_MPAP1SLVDMSCR 0xFF842104 -#define ADM_AXI_MPAP2SLVDMSCR 0xFF842108 -#define ADM_AXI_MPAP3SLVDMSCR 0xFF84210C - -#define DM_AXI_RDMDMSCR 0xFF852000 -#define DM_AXI_SDM0DMSCR 0xFF852004 -#define DM_AXI_SDM1DMSCR 0xFF852008 -#define DM_AXI_MMAP0SLVDMSCR 0xFF852100 -#define DM_AXI_MMAP1SLVDMSCR 0xFF852104 -#define DM_AXI_QSPAPSLVDMSCR 0xFF852108 -#define DM_AXI_RAP4SLVDMSCR 0xFF85210C -#define DM_AXI_RAP5SLVDMSCR 0xFF852110 -#define DM_AXI_SAP4SLVDMSCR 0xFF852114 -#define DM_AXI_SAP5SLVDMSCR 0xFF852118 -#define DM_AXI_SAP6SLVDMSCR 0xFF85211C -#define DM_AXI_SAP65SLVDMSCR 0xFF852120 -#define DM_AXI_SDAP0SLVDMSCR 0xFF852124 -#define DM_AXI_SDAP1SLVDMSCR 0xFF852128 -#define DM_AXI_SDAP2SLVDMSCR 0xFF85212C -#define DM_AXI_SDAP3SLVDMSCR 0xFF852130 - -#define SYS_AXI256_SYXDMSCR 0xFF862000 -#define SYS_AXI256_MPXDMSCR 0xFF862004 -#define SYS_AXI256_MXIDMSCR 0xFF862008 -#define SYS_AXI256_X128TO256SLVDMSCR 0xFF862100 -#define SYS_AXI256_X256TO128SLVDMSCR 0xFF862104 -#define SYS_AXI256_SYXSLVDMSCR 0xFF862108 -#define SYS_AXI256_CCXSLVDMSCR 0xFF86210C -#define SYS_AXI256_S3CSLVDMSCR 0xFF862110 - -#define MXT_SYXDMSCR 0xFF872000 -#define MXT_CMM0SLVDMSCR 0xFF872100 -#define MXT_CMM1SLVDMSCR 0xFF872104 -#define MXT_CMM2SLVDMSCR 0xFF872108 -#define MXT_FDPSLVDMSCR 0xFF87210C -#define MXT_IMRSLVDMSCR 0xFF872110 -#define MXT_VINSLVDMSCR 0xFF872114 -#define MXT_VPC0SLVDMSCR 0xFF872118 -#define MXT_VPC1SLVDMSCR 0xFF87211C -#define MXT_VSP0SLVDMSCR 0xFF872120 -#define MXT_VSP1SLVDMSCR 0xFF872124 -#define MXT_VSPD0SLVDMSCR 0xFF872128 -#define MXT_VSPD1SLVDMSCR 0xFF87212C -#define MXT_MAP1SLVDMSCR 0xFF872130 -#define MXT_MAP2SLVDMSCR 0xFF872134 - -#define CCI_AXI_MMUS0DMSCR 0xFF882000 -#define CCI_AXI_SYX2DMSCR 0xFF882004 -#define CCI_AXI_MMURDMSCR 0xFF882008 -#define CCI_AXI_MMUDSDMSCR 0xFF88200C -#define CCI_AXI_MMUMDMSCR 0xFF882010 -#define CCI_AXI_MXIDMSCR 0xFF882014 -#define CCI_AXI_MMUS1DMSCR 0xFF882018 -#define CCI_AXI_MMUMPDMSCR 0xFF88201C -#define CCI_AXI_DVMDMSCR 0xFF882020 -#define CCI_AXI_CCISLVDMSCR 0xFF882100 - -#define CCI_AXI_IPMMUIDVMCR 0xFF880400 -#define CCI_AXI_IPMMURDVMCR 0xFF880404 -#define CCI_AXI_IPMMUS0DVMCR 0xFF880408 -#define CCI_AXI_IPMMUS1DVMCR 0xFF88040C -#define CCI_AXI_IPMMUMPDVMCR 0xFF880410 -#define CCI_AXI_IPMMUDSDVMCR 0xFF880414 -#define CCI_AXI_AX2ADDRMASK 0xFF88041C - -#ifndef __ASSEMBLY__ -#include <asm/types.h> - -/* RWDT */ -struct r8a7791_rwdt { - u32 rwtcnt; /* 0x00 */ - u32 rwtcsra; /* 0x04 */ - u16 rwtcsrb; /* 0x08 */ -}; - -/* SWDT */ -struct r8a7791_swdt { - u32 swtcnt; /* 0x00 */ - u32 swtcsra; /* 0x04 */ - u16 swtcsrb; /* 0x08 */ -}; - -/* LBSC */ -struct r8a7791_lbsc { - u32 cs0ctrl; - u32 cs1ctrl; - u32 ecs0ctrl; - u32 ecs1ctrl; - u32 ecs2ctrl; - u32 ecs3ctrl; - u32 ecs4ctrl; - u32 ecs5ctrl; - u32 dummy0[4]; /* 0x20 .. 0x2C */ - u32 cswcr0; - u32 cswcr1; - u32 ecswcr0; - u32 ecswcr1; - u32 ecswcr2; - u32 ecswcr3; - u32 ecswcr4; - u32 ecswcr5; - u32 exdmawcr0; - u32 exdmawcr1; - u32 exdmawcr2; - u32 dummy1[9]; /* 0x5C .. 0x7C */ - u32 cspwcr0; - u32 cspwcr1; - u32 ecspwcr0; - u32 ecspwcr1; - u32 ecspwcr2; - u32 ecspwcr3; - u32 ecspwcr4; - u32 ecspwcr5; - u32 exwtsync; - u32 dummy2[3]; /* 0xA4 .. 0xAC */ - u32 cs0bstctl; - u32 cs0btph; - u32 dummy3[2]; /* 0xB8 .. 0xBC */ - u32 cs1gdst; - u32 ecs0gdst; - u32 ecs1gdst; - u32 ecs2gdst; - u32 ecs3gdst; - u32 ecs4gdst; - u32 ecs5gdst; - u32 dummy4[5]; /* 0xDC .. 0xEC */ - u32 exdmaset0; - u32 exdmaset1; - u32 exdmaset2; - u32 dummy5[5]; /* 0xFC .. 0x10C */ - u32 exdmcr0; - u32 exdmcr1; - u32 exdmcr2; - u32 dummy6[5]; /* 0x11C .. 0x12C */ - u32 bcintsr; - u32 bcintcr; - u32 bcintmr; - u32 dummy7; /* 0x13C */ - u32 exbatlv; - u32 exwtsts; - u32 dummy8[14]; /* 0x148 .. 0x17C */ - u32 atacsctrl; - u32 dummy9[15]; /* 0x184 .. 0x1BC */ - u32 exbct; - u32 extct; -}; - -/* DBSC3 */ -struct r8a7791_dbsc3 { - u32 dummy0[3]; /* 0x00 .. 0x08 */ - u32 dbstate1; - u32 dbacen; - u32 dbrfen; - u32 dbcmd; - u32 dbwait; - u32 dbkind; - u32 dbconf0; - u32 dummy1[2]; /* 0x28 .. 0x2C */ - u32 dbphytype; - u32 dummy2[3]; /* 0x34 .. 0x3C */ - u32 dbtr0; - u32 dbtr1; - u32 dbtr2; - u32 dummy3; /* 0x4C */ - u32 dbtr3; - u32 dbtr4; - u32 dbtr5; - u32 dbtr6; - u32 dbtr7; - u32 dbtr8; - u32 dbtr9; - u32 dbtr10; - u32 dbtr11; - u32 dbtr12; - u32 dbtr13; - u32 dbtr14; - u32 dbtr15; - u32 dbtr16; - u32 dbtr17; - u32 dbtr18; - u32 dbtr19; - u32 dummy4[7]; /* 0x94 .. 0xAC */ - u32 dbbl; - u32 dummy5[3]; /* 0xB4 .. 0xBC */ - u32 dbadj0; - u32 dummy6; /* 0xC4 */ - u32 dbadj2; - u32 dummy7[5]; /* 0xCC .. 0xDC */ - u32 dbrfcnf0; - u32 dbrfcnf1; - u32 dbrfcnf2; - u32 dummy8[2]; /* 0xEC .. 0xF0 */ - u32 dbcalcnf; - u32 dbcaltr; - u32 dummy9; /* 0xFC */ - u32 dbrnk0; - u32 dummy10[31]; /* 0x104 .. 0x17C */ - u32 dbpdncnf; - u32 dummy11[47]; /* 0x184 ..0x23C */ - u32 dbdfistat; - u32 dbdficnt; - u32 dummy12[14]; /* 0x248 .. 0x27C */ - u32 dbpdlck; - u32 dummy13[3]; /* 0x284 .. 0x28C */ - u32 dbpdrga; - u32 dummy14[3]; /* 0x294 .. 0x29C */ - u32 dbpdrgd; - u32 dummy15[24]; /* 0x2A4 .. 0x300 */ - u32 dbbs0cnt1; - u32 dummy16[30]; /* 0x308 .. 0x37C */ - u32 dbwt0cnf0; - u32 dbwt0cnf1; - u32 dbwt0cnf2; - u32 dbwt0cnf3; - u32 dbwt0cnf4; -}; - -/* GPIO */ -struct r8a7791_gpio { - u32 iointsel; - u32 inoutsel; - u32 outdt; - u32 indt; - u32 intdt; - u32 intclr; - u32 intmsk; - u32 posneg; - u32 edglevel; - u32 filonoff; - u32 intmsks; - u32 mskclrs; - u32 outdtsel; - u32 outdth; - u32 outdtl; - u32 bothedge; -}; - -/* S3C(QoS) */ -struct r8a7791_s3c { - u32 s3cexcladdmsk; - u32 s3cexclidmsk; - u32 s3cadsplcr; - u32 s3cmaar; - u32 dummy0; /* 0x10 */ - u32 s3crorr; - u32 s3cworr; - u32 s3carcr22; - u32 dummy1[2]; /* 0x20 .. 0x24 */ - u32 s3cmctr; - u32 dummy2; /* 0x2C */ - u32 cconf0; - u32 cconf1; - u32 cconf2; - u32 cconf3; -}; - -struct r8a7791_s3c_qos { - u32 s3cqos0; - u32 s3cqos1; - u32 s3cqos2; - u32 s3cqos3; - u32 s3cqos4; - u32 s3cqos5; - u32 s3cqos6; - u32 s3cqos7; - u32 s3cqos8; -}; - -/* DBSC(QoS) */ -struct r8a7791_dbsc3_qos { - u32 dblgcnt; - u32 dbtmval0; - u32 dbtmval1; - u32 dbtmval2; - u32 dbtmval3; - u32 dbrqctr; - u32 dbthres0; - u32 dbthres1; - u32 dbthres2; - u32 dummy0; /* 0x24 */ - u32 dblgqon; -}; - -/* MXI(QoS) */ -struct r8a7791_mxi { - u32 mxsaar0; - u32 mxsaar1; - u32 dummy0[8]; /* 0x08 .. 0x24 */ - u32 mxs3cracr; - u32 dummy1[3]; /* 0x2C .. 0x34 */ - u32 mxs3cwacr; - u32 dummy2; /* 0x3C */ - u32 mxrtcr; - u32 mxwtcr; -}; - -struct r8a7791_mxi_qos { - u32 vspdu0; - u32 vspdu1; - u32 du0; - u32 du1; -}; - -/* AXI(QoS) */ -struct r8a7791_axi_qos { - u32 qosconf; - u32 qosctset0; - u32 qosctset1; - u32 qosctset2; - u32 qosctset3; - u32 qosreqctr; - u32 qosthres0; - u32 qosthres1; - u32 qosthres2; - u32 qosqon; -}; - -#endif +#define R8A7791_CUT_ES2X 2 +#define IS_R8A7791_ES2() \ + (rmobile_get_cpu_rev_integer() == R8A7791_CUT_ES2X) #endif /* __ASM_ARCH_R8A7791_H */ diff --git a/arch/arm/include/asm/arch-rmobile/rcar-base.h b/arch/arm/include/asm/arch-rmobile/rcar-base.h new file mode 100644 index 0000000000..4331d3137c --- /dev/null +++ b/arch/arm/include/asm/arch-rmobile/rcar-base.h @@ -0,0 +1,637 @@ +/* + * arch/arm/include/asm/arch-rmobile/rcar-base.h + * + * Copyright (C) 2013,2014 Renesas Electronics Corporation + * + * SPDX-License-Identifier: GPL-2.0 +*/ + +#ifndef __ASM_ARCH_RCAR_BASE_H +#define __ASM_ARCH_RCAR_BASE_H + +/* + * R-Car (R8A7790/R8A7791) I/O Addresses + */ +#define RWDT_BASE 0xE6020000 +#define SWDT_BASE 0xE6030000 +#define LBSC_BASE 0xFEC00200 +#define DBSC3_0_BASE 0xE6790000 +#define DBSC3_1_BASE 0xE67A0000 +#define TMU_BASE 0xE61E0000 +#define GPIO5_BASE 0xE6055000 +#define SH_QSPI_BASE 0xE6B10000 + +#define S3C_BASE 0xE6784000 +#define S3C_INT_BASE 0xE6784A00 +#define S3C_MEDIA_BASE 0xE6784B00 + +#define S3C_QOS_DCACHE_BASE 0xE6784BDC +#define S3C_QOS_CCI0_BASE 0xE6784C00 +#define S3C_QOS_CCI1_BASE 0xE6784C24 +#define S3C_QOS_MXI_BASE 0xE6784C48 +#define S3C_QOS_AXI_BASE 0xE6784C6C + +#define DBSC3_0_QOS_R0_BASE 0xE6791000 +#define DBSC3_0_QOS_R1_BASE 0xE6791100 +#define DBSC3_0_QOS_R2_BASE 0xE6791200 +#define DBSC3_0_QOS_R3_BASE 0xE6791300 +#define DBSC3_0_QOS_R4_BASE 0xE6791400 +#define DBSC3_0_QOS_R5_BASE 0xE6791500 +#define DBSC3_0_QOS_R6_BASE 0xE6791600 +#define DBSC3_0_QOS_R7_BASE 0xE6791700 +#define DBSC3_0_QOS_R8_BASE 0xE6791800 +#define DBSC3_0_QOS_R9_BASE 0xE6791900 +#define DBSC3_0_QOS_R10_BASE 0xE6791A00 +#define DBSC3_0_QOS_R11_BASE 0xE6791B00 +#define DBSC3_0_QOS_R12_BASE 0xE6791C00 +#define DBSC3_0_QOS_R13_BASE 0xE6791D00 +#define DBSC3_0_QOS_R14_BASE 0xE6791E00 +#define DBSC3_0_QOS_R15_BASE 0xE6791F00 +#define DBSC3_0_QOS_W0_BASE 0xE6792000 +#define DBSC3_0_QOS_W1_BASE 0xE6792100 +#define DBSC3_0_QOS_W2_BASE 0xE6792200 +#define DBSC3_0_QOS_W3_BASE 0xE6792300 +#define DBSC3_0_QOS_W4_BASE 0xE6792400 +#define DBSC3_0_QOS_W5_BASE 0xE6792500 +#define DBSC3_0_QOS_W6_BASE 0xE6792600 +#define DBSC3_0_QOS_W7_BASE 0xE6792700 +#define DBSC3_0_QOS_W8_BASE 0xE6792800 +#define DBSC3_0_QOS_W9_BASE 0xE6792900 +#define DBSC3_0_QOS_W10_BASE 0xE6792A00 +#define DBSC3_0_QOS_W11_BASE 0xE6792B00 +#define DBSC3_0_QOS_W12_BASE 0xE6792C00 +#define DBSC3_0_QOS_W13_BASE 0xE6792D00 +#define DBSC3_0_QOS_W14_BASE 0xE6792E00 +#define DBSC3_0_QOS_W15_BASE 0xE6792F00 +#define DBSC3_0_DBADJ2 0xE67900C8 + +#define CCI_400_MAXOT_1 0xF0091110 +#define CCI_400_MAXOT_2 0xF0092110 +#define CCI_400_QOSCNTL_1 0xF009110C +#define CCI_400_QOSCNTL_2 0xF009210C + +#define MXI_BASE 0xFE960000 +#define MXI_QOS_BASE 0xFE960300 + +#define SYS_AXI_SYX64TO128_BASE 0xFF800300 +#define SYS_AXI_AVB_BASE 0xFF800340 +#define SYS_AXI_G2D_BASE 0xFF800540 +#define SYS_AXI_IMP0_BASE 0xFF800580 +#define SYS_AXI_IMP1_BASE 0xFF8005C0 +#define SYS_AXI_IMUX0_BASE 0xFF800600 +#define SYS_AXI_IMUX1_BASE 0xFF800640 +#define SYS_AXI_IMUX2_BASE 0xFF800680 +#define SYS_AXI_LBS_BASE 0xFF8006C0 +#define SYS_AXI_MMUDS_BASE 0xFF800700 +#define SYS_AXI_MMUM_BASE 0xFF800740 +#define SYS_AXI_MMUR_BASE 0xFF800780 +#define SYS_AXI_MMUS0_BASE 0xFF8007C0 +#define SYS_AXI_MMUS1_BASE 0xFF800800 +#define SYS_AXI_MTSB0_BASE 0xFF800880 +#define SYS_AXI_MTSB1_BASE 0xFF8008C0 +#define SYS_AXI_PCI_BASE 0xFF800900 +#define SYS_AXI_RTX_BASE 0xFF800940 +#define SYS_AXI_SDS0_BASE 0xFF800A80 +#define SYS_AXI_SDS1_BASE 0xFF800AC0 +#define SYS_AXI_USB20_BASE 0xFF800C00 +#define SYS_AXI_USB21_BASE 0xFF800C40 +#define SYS_AXI_USB22_BASE 0xFF800C80 +#define SYS_AXI_USB30_BASE 0xFF800CC0 +#define SYS_AXI_AX2M_BASE 0xFF800380 +#define SYS_AXI_CC50_BASE 0xFF8003C0 +#define SYS_AXI_CCI_BASE 0xFF800440 +#define SYS_AXI_CS_BASE 0xFF800480 +#define SYS_AXI_DDM_BASE 0xFF8004C0 +#define SYS_AXI_ETH_BASE 0xFF800500 +#define SYS_AXI_MPXM_BASE 0xFF800840 +#define SYS_AXI_SAT0_BASE 0xFF800980 +#define SYS_AXI_SAT1_BASE 0xFF8009C0 +#define SYS_AXI_SDM0_BASE 0xFF800A00 +#define SYS_AXI_SDM1_BASE 0xFF800A40 +#define SYS_AXI_TRAB_BASE 0xFF800B00 +#define SYS_AXI_UDM0_BASE 0xFF800B80 +#define SYS_AXI_UDM1_BASE 0xFF800BC0 + +#define RT_AXI_SHX_BASE 0xFF810100 +#define RT_AXI_DBG_BASE 0xFF810140 /* R8A7791 only */ +#define RT_AXI_RDM_BASE 0xFF810180 /* R8A7791 only */ +#define RT_AXI_RDS_BASE 0xFF8101C0 +#define RT_AXI_RTX64TO128_BASE 0xFF810200 +#define RT_AXI_STPRO_BASE 0xFF810240 +#define RT_AXI_SY2RT_BASE 0xFF810280 /* R8A7791 only */ + +#define MP_AXI_ADSP_BASE 0xFF820100 +#define MP_AXI_ASDS0_BASE 0xFF8201C0 +#define MP_AXI_ASDS1_BASE 0xFF820200 +#define MP_AXI_MLP_BASE 0xFF820240 +#define MP_AXI_MMUMP_BASE 0xFF820280 +#define MP_AXI_SPU_BASE 0xFF8202C0 +#define MP_AXI_SPUC_BASE 0xFF820300 + +#define SYS_AXI256_AXI128TO256_BASE 0xFF860100 +#define SYS_AXI256_SYX_BASE 0xFF860140 +#define SYS_AXI256_MPX_BASE 0xFF860180 +#define SYS_AXI256_MXI_BASE 0xFF8601C0 + +#define CCI_AXI_MMUS0_BASE 0xFF880100 +#define CCI_AXI_SYX2_BASE 0xFF880140 +#define CCI_AXI_MMUR_BASE 0xFF880180 +#define CCI_AXI_MMUDS_BASE 0xFF8801C0 +#define CCI_AXI_MMUM_BASE 0xFF880200 +#define CCI_AXI_MXI_BASE 0xFF880240 +#define CCI_AXI_MMUS1_BASE 0xFF880280 +#define CCI_AXI_MMUMP_BASE 0xFF8802C0 + +#define MEDIA_AXI_MXR_BASE 0xFE960080 /* R8A7791 only */ +#define MEDIA_AXI_MXW_BASE 0xFE9600C0 /* R8A7791 only */ +#define MEDIA_AXI_JPR_BASE 0xFE964100 +#define MEDIA_AXI_JPW_BASE 0xFE966100 +#define MEDIA_AXI_GCU0R_BASE 0xFE964140 +#define MEDIA_AXI_GCU0W_BASE 0xFE966140 +#define MEDIA_AXI_GCU1R_BASE 0xFE964180 +#define MEDIA_AXI_GCU1W_BASE 0xFE966180 +#define MEDIA_AXI_TDMR_BASE 0xFE964500 +#define MEDIA_AXI_TDMW_BASE 0xFE966500 +#define MEDIA_AXI_VSP0CR_BASE 0xFE964540 +#define MEDIA_AXI_VSP0CW_BASE 0xFE966540 +#define MEDIA_AXI_VSP1CR_BASE 0xFE964580 +#define MEDIA_AXI_VSP1CW_BASE 0xFE966580 +#define MEDIA_AXI_VSPDU0CR_BASE 0xFE9645C0 +#define MEDIA_AXI_VSPDU0CW_BASE 0xFE9665C0 +#define MEDIA_AXI_VSPDU1CR_BASE 0xFE964600 +#define MEDIA_AXI_VSPDU1CW_BASE 0xFE966600 +#define MEDIA_AXI_VIN0W_BASE 0xFE966900 +#define MEDIA_AXI_VSP0R_BASE 0xFE964D00 +#define MEDIA_AXI_VSP0W_BASE 0xFE966D00 +#define MEDIA_AXI_FDP0R_BASE 0xFE964D40 +#define MEDIA_AXI_FDP0W_BASE 0xFE966D40 +#define MEDIA_AXI_IMSR_BASE 0xFE964D80 +#define MEDIA_AXI_IMSW_BASE 0xFE966D80 +#define MEDIA_AXI_VSP1R_BASE 0xFE965100 +#define MEDIA_AXI_VSP1W_BASE 0xFE967100 +#define MEDIA_AXI_FDP1R_BASE 0xFE965140 +#define MEDIA_AXI_FDP1W_BASE 0xFE967140 +#define MEDIA_AXI_IMRR_BASE 0xFE965180 +#define MEDIA_AXI_IMRW_BASE 0xFE967180 +#define MEDIA_AXI_FDP2R_BASE 0xFE9651C0 +#define MEDIA_AXI_FDP2W_BASE 0xFE966DC0 +#define MEDIA_AXI_VSPD0R_BASE 0xFE965500 +#define MEDIA_AXI_VSPD0W_BASE 0xFE967500 +#define MEDIA_AXI_VSPD1R_BASE 0xFE965540 +#define MEDIA_AXI_VSPD1W_BASE 0xFE967540 +#define MEDIA_AXI_DU0R_BASE 0xFE965580 +#define MEDIA_AXI_DU0W_BASE 0xFE967580 +#define MEDIA_AXI_DU1R_BASE 0xFE9655C0 +#define MEDIA_AXI_DU1W_BASE 0xFE9675C0 +#define MEDIA_AXI_VCP0CR_BASE 0xFE965900 +#define MEDIA_AXI_VCP0CW_BASE 0xFE967900 +#define MEDIA_AXI_VCP0VR_BASE 0xFE965940 +#define MEDIA_AXI_VCP0VW_BASE 0xFE967940 +#define MEDIA_AXI_VPC0R_BASE 0xFE965980 +#define MEDIA_AXI_VCP1CR_BASE 0xFE965D00 +#define MEDIA_AXI_VCP1CW_BASE 0xFE967D00 +#define MEDIA_AXI_VCP1VR_BASE 0xFE965D40 +#define MEDIA_AXI_VCP1VW_BASE 0xFE967D40 +#define MEDIA_AXI_VPC1R_BASE 0xFE965D80 + +#define SYS_AXI_AVBDMSCR 0xFF802000 +#define SYS_AXI_SYX2DMSCR 0xFF802004 +#define SYS_AXI_CC50DMSCR 0xFF802008 +#define SYS_AXI_CC51DMSCR 0xFF80200C +#define SYS_AXI_CCIDMSCR 0xFF802010 +#define SYS_AXI_CSDMSCR 0xFF802014 +#define SYS_AXI_DDMDMSCR 0xFF802018 +#define SYS_AXI_ETHDMSCR 0xFF80201C +#define SYS_AXI_G2DDMSCR 0xFF802020 +#define SYS_AXI_IMP0DMSCR 0xFF802024 +#define SYS_AXI_IMP1DMSCR 0xFF802028 +#define SYS_AXI_LBSDMSCR 0xFF80202C +#define SYS_AXI_MMUDSDMSCR 0xFF802030 +#define SYS_AXI_MMUMXDMSCR 0xFF802034 +#define SYS_AXI_MMURDDMSCR 0xFF802038 +#define SYS_AXI_MMUS0DMSCR 0xFF80203C +#define SYS_AXI_MMUS1DMSCR 0xFF802040 +#define SYS_AXI_MPXDMSCR 0xFF802044 +#define SYS_AXI_MTSB0DMSCR 0xFF802048 +#define SYS_AXI_MTSB1DMSCR 0xFF80204C +#define SYS_AXI_PCIDMSCR 0xFF802050 +#define SYS_AXI_RTXDMSCR 0xFF802054 +#define SYS_AXI_SAT0DMSCR 0xFF802058 +#define SYS_AXI_SAT1DMSCR 0xFF80205C +#define SYS_AXI_SDM0DMSCR 0xFF802060 +#define SYS_AXI_SDM1DMSCR 0xFF802064 +#define SYS_AXI_SDS0DMSCR 0xFF802068 +#define SYS_AXI_SDS1DMSCR 0xFF80206C +#define SYS_AXI_ETRABDMSCR 0xFF802070 +#define SYS_AXI_ETRKFDMSCR 0xFF802074 +#define SYS_AXI_UDM0DMSCR 0xFF802078 +#define SYS_AXI_UDM1DMSCR 0xFF80207C +#define SYS_AXI_USB20DMSCR 0xFF802080 +#define SYS_AXI_USB21DMSCR 0xFF802084 +#define SYS_AXI_USB22DMSCR 0xFF802088 +#define SYS_AXI_USB30DMSCR 0xFF80208C +#define SYS_AXI_X128TO64SLVDMSCR 0xFF802100 +#define SYS_AXI_X64TO128SLVDMSCR 0xFF802104 +#define SYS_AXI_AVBSLVDMSCR 0xFF802108 +#define SYS_AXI_SYX2SLVDMSCR 0xFF80210C +#define SYS_AXI_ETHSLVDMSCR 0xFF802110 +#define SYS_AXI_GICSLVDMSCR 0xFF802114 +#define SYS_AXI_IMPSLVDMSCR 0xFF802118 +#define SYS_AXI_IMX0SLVDMSCR 0xFF80211C +#define SYS_AXI_IMX1SLVDMSCR 0xFF802120 +#define SYS_AXI_IMX2SLVDMSCR 0xFF802124 +#define SYS_AXI_LBSSLVDMSCR 0xFF802128 +#define SYS_AXI_MMC0SLVDMSCR 0xFF80212C +#define SYS_AXI_MMC1SLVDMSCR 0xFF802130 +#define SYS_AXI_MPXSLVDMSCR 0xFF802134 +#define SYS_AXI_MTSB0SLVDMSCR 0xFF802138 +#define SYS_AXI_MTSB1SLVDMSCR 0xFF80213C +#define SYS_AXI_MXTSLVDMSCR 0xFF802140 +#define SYS_AXI_PCISLVDMSCR 0xFF802144 +#define SYS_AXI_SYAPBSLVDMSCR 0xFF802148 +#define SYS_AXI_QSAPBSLVDMSCR 0xFF80214C +#define SYS_AXI_RTXSLVDMSCR 0xFF802150 +#define SYS_AXI_SAT0SLVDMSCR 0xFF802168 +#define SYS_AXI_SAT1SLVDMSCR 0xFF80216C +#define SYS_AXI_SDAP0SLVDMSCR 0xFF802170 +#define SYS_AXI_SDAP1SLVDMSCR 0xFF802174 +#define SYS_AXI_SDAP2SLVDMSCR 0xFF802178 +#define SYS_AXI_SDAP3SLVDMSCR 0xFF80217C +#define SYS_AXI_SGXSLVDMSCR 0xFF802180 +#define SYS_AXI_STBSLVDMSCR 0xFF802188 +#define SYS_AXI_STMSLVDMSCR 0xFF80218C +#define SYS_AXI_TSPL0SLVDMSCR 0xFF802194 +#define SYS_AXI_TSPL1SLVDMSCR 0xFF802198 +#define SYS_AXI_TSPL2SLVDMSCR 0xFF80219C +#define SYS_AXI_USB20SLVDMSCR 0xFF8021A0 +#define SYS_AXI_USB21SLVDMSCR 0xFF8021A4 +#define SYS_AXI_USB22SLVDMSCR 0xFF8021A8 +#define SYS_AXI_USB30SLVDMSCR 0xFF8021AC + +#define RT_AXI_CBMDMSCR 0xFF812000 +#define RT_AXI_DBDMSCR 0xFF812004 +#define RT_AXI_RDMDMSCR 0xFF812008 +#define RT_AXI_RDSDMSCR 0xFF81200C +#define RT_AXI_STRDMSCR 0xFF812010 +#define RT_AXI_SY2RTDMSCR 0xFF812014 +#define RT_AXI_CBSSLVDMSCR 0xFF812100 +#define RT_AXI_DBSSLVDMSCR 0xFF812104 +#define RT_AXI_RTAP1SLVDMSCR 0xFF812108 +#define RT_AXI_RTAP2SLVDMSCR 0xFF81210C +#define RT_AXI_RTAP3SLVDMSCR 0xFF812110 +#define RT_AXI_RT2SYSLVDMSCR 0xFF812114 +#define RT_AXI_A128TO64SLVDMSCR 0xFF812118 +#define RT_AXI_A64TO128SLVDMSCR 0xFF81211C +#define RT_AXI_A64TO128CSLVDMSCR 0xFF812120 +#define RT_AXI_UTLBRSLVDMSCR 0xFF812128 + +#define MP_AXI_ADSPDMSCR 0xFF822000 +#define MP_AXI_ASDM0DMSCR 0xFF822004 +#define MP_AXI_ASDM1DMSCR 0xFF822008 +#define MP_AXI_ASDS0DMSCR 0xFF82200C +#define MP_AXI_ASDS1DMSCR 0xFF822010 +#define MP_AXI_MLPDMSCR 0xFF822014 +#define MP_AXI_MMUMPDMSCR 0xFF822018 +#define MP_AXI_SPUDMSCR 0xFF82201C +#define MP_AXI_SPUCDMSCR 0xFF822020 +#define MP_AXI_SY2MPDMSCR 0xFF822024 +#define MP_AXI_ADSPSLVDMSCR 0xFF822100 +#define MP_AXI_MLMSLVDMSCR 0xFF822104 +#define MP_AXI_MPAP4SLVDMSCR 0xFF822108 +#define MP_AXI_MPAP5SLVDMSCR 0xFF82210C +#define MP_AXI_MPAP6SLVDMSCR 0xFF822110 +#define MP_AXI_MPAP7SLVDMSCR 0xFF822114 +#define MP_AXI_MP2SYSLVDMSCR 0xFF822118 +#define MP_AXI_MP2SY2SLVDMSCR 0xFF82211C +#define MP_AXI_MPXAPSLVDMSCR 0xFF822124 +#define MP_AXI_SPUSLVDMSCR 0xFF822128 +#define MP_AXI_UTLBMPSLVDMSCR 0xFF82212C + +#define ADM_AXI_ASDM0DMSCR 0xFF842000 +#define ADM_AXI_ASDM1DMSCR 0xFF842004 +#define ADM_AXI_MPAP1SLVDMSCR 0xFF842104 +#define ADM_AXI_MPAP2SLVDMSCR 0xFF842108 +#define ADM_AXI_MPAP3SLVDMSCR 0xFF84210C + +#define DM_AXI_RDMDMSCR 0xFF852000 +#define DM_AXI_SDM0DMSCR 0xFF852004 +#define DM_AXI_SDM1DMSCR 0xFF852008 +#define DM_AXI_MMAP0SLVDMSCR 0xFF852100 +#define DM_AXI_MMAP1SLVDMSCR 0xFF852104 +#define DM_AXI_QSPAPSLVDMSCR 0xFF852108 +#define DM_AXI_RAP4SLVDMSCR 0xFF85210C +#define DM_AXI_RAP5SLVDMSCR 0xFF852110 +#define DM_AXI_SAP4SLVDMSCR 0xFF852114 +#define DM_AXI_SAP5SLVDMSCR 0xFF852118 +#define DM_AXI_SAP6SLVDMSCR 0xFF85211C +#define DM_AXI_SAP65SLVDMSCR 0xFF852120 +#define DM_AXI_SDAP0SLVDMSCR 0xFF852124 +#define DM_AXI_SDAP1SLVDMSCR 0xFF852128 +#define DM_AXI_SDAP2SLVDMSCR 0xFF85212C +#define DM_AXI_SDAP3SLVDMSCR 0xFF852130 + +#define SYS_AXI256_SYXDMSCR 0xFF862000 +#define SYS_AXI256_MPXDMSCR 0xFF862004 +#define SYS_AXI256_MXIDMSCR 0xFF862008 +#define SYS_AXI256_X128TO256SLVDMSCR 0xFF862100 +#define SYS_AXI256_X256TO128SLVDMSCR 0xFF862104 +#define SYS_AXI256_SYXSLVDMSCR 0xFF862108 +#define SYS_AXI256_CCXSLVDMSCR 0xFF86210C +#define SYS_AXI256_S3CSLVDMSCR 0xFF862110 + +#define MXT_SYXDMSCR 0xFF872000 +#define MXT_CMM0SLVDMSCR 0xFF872100 +#define MXT_CMM1SLVDMSCR 0xFF872104 +#define MXT_CMM2SLVDMSCR 0xFF872108 +#define MXT_FDPSLVDMSCR 0xFF87210C +#define MXT_IMRSLVDMSCR 0xFF872110 +#define MXT_VINSLVDMSCR 0xFF872114 +#define MXT_VPC0SLVDMSCR 0xFF872118 +#define MXT_VPC1SLVDMSCR 0xFF87211C +#define MXT_VSP0SLVDMSCR 0xFF872120 +#define MXT_VSP1SLVDMSCR 0xFF872124 +#define MXT_VSPD0SLVDMSCR 0xFF872128 +#define MXT_VSPD1SLVDMSCR 0xFF87212C +#define MXT_MAP1SLVDMSCR 0xFF872130 +#define MXT_MAP2SLVDMSCR 0xFF872134 + +#define CCI_AXI_MMUS0DMSCR 0xFF882000 +#define CCI_AXI_SYX2DMSCR 0xFF882004 +#define CCI_AXI_MMURDMSCR 0xFF882008 +#define CCI_AXI_MMUDSDMSCR 0xFF88200C +#define CCI_AXI_MMUMDMSCR 0xFF882010 +#define CCI_AXI_MXIDMSCR 0xFF882014 +#define CCI_AXI_MMUS1DMSCR 0xFF882018 +#define CCI_AXI_MMUMPDMSCR 0xFF88201C +#define CCI_AXI_DVMDMSCR 0xFF882020 +#define CCI_AXI_CCISLVDMSCR 0xFF882100 + +#define CCI_AXI_IPMMUIDVMCR 0xFF880400 +#define CCI_AXI_IPMMURDVMCR 0xFF880404 +#define CCI_AXI_IPMMUS0DVMCR 0xFF880408 +#define CCI_AXI_IPMMUS1DVMCR 0xFF88040C +#define CCI_AXI_IPMMUMPDVMCR 0xFF880410 +#define CCI_AXI_IPMMUDSDVMCR 0xFF880414 +#define CCI_AXI_AX2ADDRMASK 0xFF88041C + +#define PLL0CR 0xE61500D8 +#define PLL0_STC_MASK 0x7F000000 +#define PLL0_STC_BIT 24 + +#ifndef __ASSEMBLY__ +#include <asm/types.h> + +/* RWDT */ +struct rcar_rwdt { + u32 rwtcnt; /* 0x00 */ + u32 rwtcsra; /* 0x04 */ + u16 rwtcsrb; /* 0x08 */ +}; + +/* SWDT */ +struct rcar_swdt { + u32 swtcnt; /* 0x00 */ + u32 swtcsra; /* 0x04 */ + u16 swtcsrb; /* 0x08 */ +}; + +/* LBSC */ +struct rcar_lbsc { + u32 cs0ctrl; + u32 cs1ctrl; + u32 ecs0ctrl; + u32 ecs1ctrl; + u32 ecs2ctrl; + u32 ecs3ctrl; + u32 ecs4ctrl; + u32 ecs5ctrl; + u32 dummy0[4]; /* 0x20 .. 0x2C */ + u32 cswcr0; + u32 cswcr1; + u32 ecswcr0; + u32 ecswcr1; + u32 ecswcr2; + u32 ecswcr3; + u32 ecswcr4; + u32 ecswcr5; + u32 exdmawcr0; + u32 exdmawcr1; + u32 exdmawcr2; + u32 dummy1[9]; /* 0x5C .. 0x7C */ + u32 cspwcr0; + u32 cspwcr1; + u32 ecspwcr0; + u32 ecspwcr1; + u32 ecspwcr2; + u32 ecspwcr3; + u32 ecspwcr4; + u32 ecspwcr5; + u32 exwtsync; + u32 dummy2[3]; /* 0xA4 .. 0xAC */ + u32 cs0bstctl; + u32 cs0btph; + u32 dummy3[2]; /* 0xB8 .. 0xBC */ + u32 cs1gdst; + u32 ecs0gdst; + u32 ecs1gdst; + u32 ecs2gdst; + u32 ecs3gdst; + u32 ecs4gdst; + u32 ecs5gdst; + u32 dummy4[5]; /* 0xDC .. 0xEC */ + u32 exdmaset0; + u32 exdmaset1; + u32 exdmaset2; + u32 dummy5[5]; /* 0xFC .. 0x10C */ + u32 exdmcr0; + u32 exdmcr1; + u32 exdmcr2; + u32 dummy6[5]; /* 0x11C .. 0x12C */ + u32 bcintsr; + u32 bcintcr; + u32 bcintmr; + u32 dummy7; /* 0x13C */ + u32 exbatlv; + u32 exwtsts; + u32 dummy8[14]; /* 0x148 .. 0x17C */ + u32 atacsctrl; + u32 dummy9[15]; /* 0x184 .. 0x1BC */ + u32 exbct; + u32 extct; +}; + +/* DBSC3 */ +struct rcar_dbsc3 { + u32 dummy0[3]; /* 0x00 .. 0x08 */ + u32 dbstate1; + u32 dbacen; + u32 dbrfen; + u32 dbcmd; + u32 dbwait; + u32 dbkind; + u32 dbconf0; + u32 dummy1[2]; /* 0x28 .. 0x2C */ + u32 dbphytype; + u32 dummy2[3]; /* 0x34 .. 0x3C */ + u32 dbtr0; + u32 dbtr1; + u32 dbtr2; + u32 dummy3; /* 0x4C */ + u32 dbtr3; + u32 dbtr4; + u32 dbtr5; + u32 dbtr6; + u32 dbtr7; + u32 dbtr8; + u32 dbtr9; + u32 dbtr10; + u32 dbtr11; + u32 dbtr12; + u32 dbtr13; + u32 dbtr14; + u32 dbtr15; + u32 dbtr16; + u32 dbtr17; + u32 dbtr18; + u32 dbtr19; + u32 dummy4[7]; /* 0x94 .. 0xAC */ + u32 dbbl; + u32 dummy5[3]; /* 0xB4 .. 0xBC */ + u32 dbadj0; + u32 dummy6; /* 0xC4 */ + u32 dbadj2; + u32 dummy7[5]; /* 0xCC .. 0xDC */ + u32 dbrfcnf0; + u32 dbrfcnf1; + u32 dbrfcnf2; + u32 dummy8[2]; /* 0xEC .. 0xF0 */ + u32 dbcalcnf; + u32 dbcaltr; + u32 dummy9; /* 0xFC */ + u32 dbrnk0; + u32 dummy10[31]; /* 0x104 .. 0x17C */ + u32 dbpdncnf; + u32 dummy11[47]; /* 0x184 ..0x23C */ + u32 dbdfistat; + u32 dbdficnt; + u32 dummy12[14]; /* 0x248 .. 0x27C */ + u32 dbpdlck; + u32 dummy13[3]; /* 0x284 .. 0x28C */ + u32 dbpdrga; + u32 dummy14[3]; /* 0x294 .. 0x29C */ + u32 dbpdrgd; + u32 dummy15[24]; /* 0x2A4 .. 0x300 */ + u32 dbbs0cnt1; + u32 dummy16[30]; /* 0x308 .. 0x37C */ + u32 dbwt0cnf0; + u32 dbwt0cnf1; + u32 dbwt0cnf2; + u32 dbwt0cnf3; + u32 dbwt0cnf4; +}; + +/* GPIO */ +struct rcar_gpio { + u32 iointsel; + u32 inoutsel; + u32 outdt; + u32 indt; + u32 intdt; + u32 intclr; + u32 intmsk; + u32 posneg; + u32 edglevel; + u32 filonoff; + u32 intmsks; + u32 mskclrs; + u32 outdtsel; + u32 outdth; + u32 outdtl; + u32 bothedge; +}; + +/* S3C(QoS) */ +struct rcar_s3c { + u32 s3cexcladdmsk; + u32 s3cexclidmsk; + u32 s3cadsplcr; + u32 s3cmaar; + u32 s3carcr11; + u32 s3crorr; + u32 s3cworr; + u32 s3carcr22; + u32 dummy1[2]; /* 0x20 .. 0x24 */ + u32 s3cmctr; + u32 dummy2; /* 0x2C */ + u32 cconf0; + u32 cconf1; + u32 cconf2; + u32 cconf3; +}; + +struct rcar_s3c_qos { + u32 s3cqos0; + u32 s3cqos1; + u32 s3cqos2; + u32 s3cqos3; + u32 s3cqos4; + u32 s3cqos5; + u32 s3cqos6; + u32 s3cqos7; + u32 s3cqos8; +}; + +/* DBSC(QoS) */ +struct rcar_dbsc3_qos { + u32 dblgcnt; + u32 dbtmval0; + u32 dbtmval1; + u32 dbtmval2; + u32 dbtmval3; + u32 dbrqctr; + u32 dbthres0; + u32 dbthres1; + u32 dbthres2; + u32 dummy0; /* 0x24 */ + u32 dblgqon; +}; + +/* MXI(QoS) */ +struct rcar_mxi { + u32 mxsaar0; + u32 mxsaar1; + u32 dummy0[7]; /* 0x08 .. 0x20 */ + u32 mxaxiracr; /* R8a7790 only */ + u32 mxs3cracr; + u32 dummy1[2]; /* 0x2C .. 0x30 */ + u32 mxaxiwacr; /* R8a7790 only */ + u32 mxs3cwacr; + u32 dummy2; /* 0x3C */ + u32 mxrtcr; + u32 mxwtcr; +}; + +struct rcar_mxi_qos { + u32 vspdu0; + u32 vspdu1; + u32 du0; + u32 du1; +}; + +/* AXI(QoS) */ +struct rcar_axi_qos { + u32 qosconf; + u32 qosctset0; + u32 qosctset1; + u32 qosctset2; + u32 qosctset3; + u32 qosreqctr; + u32 qosthres0; + u32 qosthres1; + u32 qosthres2; + u32 qosqon; +}; + +#endif + +#endif /* __ASM_ARCH_RCAR_BASE_H */ diff --git a/arch/arm/include/asm/arch-rmobile/rmobile.h b/arch/arm/include/asm/arch-rmobile/rmobile.h index 2382565023..ebddd7a8fe 100644 --- a/arch/arm/include/asm/arch-rmobile/rmobile.h +++ b/arch/arm/include/asm/arch-rmobile/rmobile.h @@ -15,4 +15,10 @@ #endif #endif /* CONFIG_RMOBILE */ +#ifndef __ASSEMBLY__ +u32 rmobile_get_cpu_type(void); +u32 rmobile_get_cpu_rev_integer(void); +u32 rmobile_get_cpu_rev_fraction(void); +#endif /* __ASSEMBLY__ */ + #endif /* __ASM_ARCH_RMOBILE_H */ diff --git a/arch/arm/include/asm/arch-s5pc1xx/gpio.h b/arch/arm/include/asm/arch-s5pc1xx/gpio.h index da8df74a10..d5dbc22c18 100644 --- a/arch/arm/include/asm/arch-s5pc1xx/gpio.h +++ b/arch/arm/include/asm/arch-s5pc1xx/gpio.h @@ -19,170 +19,830 @@ struct s5p_gpio_bank { unsigned char res1[8]; }; -struct s5pc100_gpio { - struct s5p_gpio_bank a0; - struct s5p_gpio_bank a1; - struct s5p_gpio_bank b; - struct s5p_gpio_bank c; - struct s5p_gpio_bank d; - struct s5p_gpio_bank e0; - struct s5p_gpio_bank e1; - struct s5p_gpio_bank f0; - struct s5p_gpio_bank f1; - struct s5p_gpio_bank f2; - struct s5p_gpio_bank f3; - struct s5p_gpio_bank g0; - struct s5p_gpio_bank g1; - struct s5p_gpio_bank g2; - struct s5p_gpio_bank g3; - struct s5p_gpio_bank i; - struct s5p_gpio_bank j0; - struct s5p_gpio_bank j1; - struct s5p_gpio_bank j2; - struct s5p_gpio_bank j3; - struct s5p_gpio_bank j4; - struct s5p_gpio_bank k0; - struct s5p_gpio_bank k1; - struct s5p_gpio_bank k2; - struct s5p_gpio_bank k3; - struct s5p_gpio_bank l0; - struct s5p_gpio_bank l1; - struct s5p_gpio_bank l2; - struct s5p_gpio_bank l3; - struct s5p_gpio_bank l4; - struct s5p_gpio_bank h0; - struct s5p_gpio_bank h1; - struct s5p_gpio_bank h2; - struct s5p_gpio_bank h3; +/* A list of valid GPIO numbers for the asm-generic/gpio.h interface */ +enum s5pc100_gpio_pin { + S5PC100_GPIO_A00, + S5PC100_GPIO_A01, + S5PC100_GPIO_A02, + S5PC100_GPIO_A03, + S5PC100_GPIO_A04, + S5PC100_GPIO_A05, + S5PC100_GPIO_A06, + S5PC100_GPIO_A07, + S5PC100_GPIO_A10, + S5PC100_GPIO_A11, + S5PC100_GPIO_A12, + S5PC100_GPIO_A13, + S5PC100_GPIO_A14, + S5PC100_GPIO_A15, + S5PC100_GPIO_A16, + S5PC100_GPIO_A17, + S5PC100_GPIO_B0, + S5PC100_GPIO_B1, + S5PC100_GPIO_B2, + S5PC100_GPIO_B3, + S5PC100_GPIO_B4, + S5PC100_GPIO_B5, + S5PC100_GPIO_B6, + S5PC100_GPIO_B7, + S5PC100_GPIO_C0, + S5PC100_GPIO_C1, + S5PC100_GPIO_C2, + S5PC100_GPIO_C3, + S5PC100_GPIO_C4, + S5PC100_GPIO_C5, + S5PC100_GPIO_C6, + S5PC100_GPIO_C7, + S5PC100_GPIO_D0, + S5PC100_GPIO_D1, + S5PC100_GPIO_D2, + S5PC100_GPIO_D3, + S5PC100_GPIO_D4, + S5PC100_GPIO_D5, + S5PC100_GPIO_D6, + S5PC100_GPIO_D7, + S5PC100_GPIO_E00, + S5PC100_GPIO_E01, + S5PC100_GPIO_E02, + S5PC100_GPIO_E03, + S5PC100_GPIO_E04, + S5PC100_GPIO_E05, + S5PC100_GPIO_E06, + S5PC100_GPIO_E07, + S5PC100_GPIO_E10, + S5PC100_GPIO_E11, + S5PC100_GPIO_E12, + S5PC100_GPIO_E13, + S5PC100_GPIO_E14, + S5PC100_GPIO_E15, + S5PC100_GPIO_E16, + S5PC100_GPIO_E17, + S5PC100_GPIO_F00, + S5PC100_GPIO_F01, + S5PC100_GPIO_F02, + S5PC100_GPIO_F03, + S5PC100_GPIO_F04, + S5PC100_GPIO_F05, + S5PC100_GPIO_F06, + S5PC100_GPIO_F07, + S5PC100_GPIO_F10, + S5PC100_GPIO_F11, + S5PC100_GPIO_F12, + S5PC100_GPIO_F13, + S5PC100_GPIO_F14, + S5PC100_GPIO_F15, + S5PC100_GPIO_F16, + S5PC100_GPIO_F17, + S5PC100_GPIO_F20, + S5PC100_GPIO_F21, + S5PC100_GPIO_F22, + S5PC100_GPIO_F23, + S5PC100_GPIO_F24, + S5PC100_GPIO_F25, + S5PC100_GPIO_F26, + S5PC100_GPIO_F27, + S5PC100_GPIO_F30, + S5PC100_GPIO_F31, + S5PC100_GPIO_F32, + S5PC100_GPIO_F33, + S5PC100_GPIO_F34, + S5PC100_GPIO_F35, + S5PC100_GPIO_F36, + S5PC100_GPIO_F37, + S5PC100_GPIO_G00, + S5PC100_GPIO_G01, + S5PC100_GPIO_G02, + S5PC100_GPIO_G03, + S5PC100_GPIO_G04, + S5PC100_GPIO_G05, + S5PC100_GPIO_G06, + S5PC100_GPIO_G07, + S5PC100_GPIO_G10, + S5PC100_GPIO_G11, + S5PC100_GPIO_G12, + S5PC100_GPIO_G13, + S5PC100_GPIO_G14, + S5PC100_GPIO_G15, + S5PC100_GPIO_G16, + S5PC100_GPIO_G17, + S5PC100_GPIO_G20, + S5PC100_GPIO_G21, + S5PC100_GPIO_G22, + S5PC100_GPIO_G23, + S5PC100_GPIO_G24, + S5PC100_GPIO_G25, + S5PC100_GPIO_G26, + S5PC100_GPIO_G27, + S5PC100_GPIO_G30, + S5PC100_GPIO_G31, + S5PC100_GPIO_G32, + S5PC100_GPIO_G33, + S5PC100_GPIO_G34, + S5PC100_GPIO_G35, + S5PC100_GPIO_G36, + S5PC100_GPIO_G37, + S5PC100_GPIO_I0, + S5PC100_GPIO_I1, + S5PC100_GPIO_I2, + S5PC100_GPIO_I3, + S5PC100_GPIO_I4, + S5PC100_GPIO_I5, + S5PC100_GPIO_I6, + S5PC100_GPIO_I7, + S5PC100_GPIO_J00, + S5PC100_GPIO_J01, + S5PC100_GPIO_J02, + S5PC100_GPIO_J03, + S5PC100_GPIO_J04, + S5PC100_GPIO_J05, + S5PC100_GPIO_J06, + S5PC100_GPIO_J07, + S5PC100_GPIO_J10, + S5PC100_GPIO_J11, + S5PC100_GPIO_J12, + S5PC100_GPIO_J13, + S5PC100_GPIO_J14, + S5PC100_GPIO_J15, + S5PC100_GPIO_J16, + S5PC100_GPIO_J17, + S5PC100_GPIO_J20, + S5PC100_GPIO_J21, + S5PC100_GPIO_J22, + S5PC100_GPIO_J23, + S5PC100_GPIO_J24, + S5PC100_GPIO_J25, + S5PC100_GPIO_J26, + S5PC100_GPIO_J27, + S5PC100_GPIO_J30, + S5PC100_GPIO_J31, + S5PC100_GPIO_J32, + S5PC100_GPIO_J33, + S5PC100_GPIO_J34, + S5PC100_GPIO_J35, + S5PC100_GPIO_J36, + S5PC100_GPIO_J37, + S5PC100_GPIO_J40, + S5PC100_GPIO_J41, + S5PC100_GPIO_J42, + S5PC100_GPIO_J43, + S5PC100_GPIO_J44, + S5PC100_GPIO_J45, + S5PC100_GPIO_J46, + S5PC100_GPIO_J47, + S5PC100_GPIO_K00, + S5PC100_GPIO_K01, + S5PC100_GPIO_K02, + S5PC100_GPIO_K03, + S5PC100_GPIO_K04, + S5PC100_GPIO_K05, + S5PC100_GPIO_K06, + S5PC100_GPIO_K07, + S5PC100_GPIO_K10, + S5PC100_GPIO_K11, + S5PC100_GPIO_K12, + S5PC100_GPIO_K13, + S5PC100_GPIO_K14, + S5PC100_GPIO_K15, + S5PC100_GPIO_K16, + S5PC100_GPIO_K17, + S5PC100_GPIO_K20, + S5PC100_GPIO_K21, + S5PC100_GPIO_K22, + S5PC100_GPIO_K23, + S5PC100_GPIO_K24, + S5PC100_GPIO_K25, + S5PC100_GPIO_K26, + S5PC100_GPIO_K27, + S5PC100_GPIO_K30, + S5PC100_GPIO_K31, + S5PC100_GPIO_K32, + S5PC100_GPIO_K33, + S5PC100_GPIO_K34, + S5PC100_GPIO_K35, + S5PC100_GPIO_K36, + S5PC100_GPIO_K37, + S5PC100_GPIO_L00, + S5PC100_GPIO_L01, + S5PC100_GPIO_L02, + S5PC100_GPIO_L03, + S5PC100_GPIO_L04, + S5PC100_GPIO_L05, + S5PC100_GPIO_L06, + S5PC100_GPIO_L07, + S5PC100_GPIO_L10, + S5PC100_GPIO_L11, + S5PC100_GPIO_L12, + S5PC100_GPIO_L13, + S5PC100_GPIO_L14, + S5PC100_GPIO_L15, + S5PC100_GPIO_L16, + S5PC100_GPIO_L17, + S5PC100_GPIO_L20, + S5PC100_GPIO_L21, + S5PC100_GPIO_L22, + S5PC100_GPIO_L23, + S5PC100_GPIO_L24, + S5PC100_GPIO_L25, + S5PC100_GPIO_L26, + S5PC100_GPIO_L27, + S5PC100_GPIO_L30, + S5PC100_GPIO_L31, + S5PC100_GPIO_L32, + S5PC100_GPIO_L33, + S5PC100_GPIO_L34, + S5PC100_GPIO_L35, + S5PC100_GPIO_L36, + S5PC100_GPIO_L37, + S5PC100_GPIO_L40, + S5PC100_GPIO_L41, + S5PC100_GPIO_L42, + S5PC100_GPIO_L43, + S5PC100_GPIO_L44, + S5PC100_GPIO_L45, + S5PC100_GPIO_L46, + S5PC100_GPIO_L47, + S5PC100_GPIO_H00, + S5PC100_GPIO_H01, + S5PC100_GPIO_H02, + S5PC100_GPIO_H03, + S5PC100_GPIO_H04, + S5PC100_GPIO_H05, + S5PC100_GPIO_H06, + S5PC100_GPIO_H07, + S5PC100_GPIO_H10, + S5PC100_GPIO_H11, + S5PC100_GPIO_H12, + S5PC100_GPIO_H13, + S5PC100_GPIO_H14, + S5PC100_GPIO_H15, + S5PC100_GPIO_H16, + S5PC100_GPIO_H17, + S5PC100_GPIO_H20, + S5PC100_GPIO_H21, + S5PC100_GPIO_H22, + S5PC100_GPIO_H23, + S5PC100_GPIO_H24, + S5PC100_GPIO_H25, + S5PC100_GPIO_H26, + S5PC100_GPIO_H27, + S5PC100_GPIO_H30, + S5PC100_GPIO_H31, + S5PC100_GPIO_H32, + S5PC100_GPIO_H33, + S5PC100_GPIO_H34, + S5PC100_GPIO_H35, + S5PC100_GPIO_H36, + S5PC100_GPIO_H37, + + S5PC100_GPIO_MAX_PORT }; -struct s5pc110_gpio { - struct s5p_gpio_bank a0; - struct s5p_gpio_bank a1; - struct s5p_gpio_bank b; - struct s5p_gpio_bank c0; - struct s5p_gpio_bank c1; - struct s5p_gpio_bank d0; - struct s5p_gpio_bank d1; - struct s5p_gpio_bank e0; - struct s5p_gpio_bank e1; - struct s5p_gpio_bank f0; - struct s5p_gpio_bank f1; - struct s5p_gpio_bank f2; - struct s5p_gpio_bank f3; - struct s5p_gpio_bank g0; - struct s5p_gpio_bank g1; - struct s5p_gpio_bank g2; - struct s5p_gpio_bank g3; - struct s5p_gpio_bank i; - struct s5p_gpio_bank j0; - struct s5p_gpio_bank j1; - struct s5p_gpio_bank j2; - struct s5p_gpio_bank j3; - struct s5p_gpio_bank j4; - struct s5p_gpio_bank mp0_1; - struct s5p_gpio_bank mp0_2; - struct s5p_gpio_bank mp0_3; - struct s5p_gpio_bank mp0_4; - struct s5p_gpio_bank mp0_5; - struct s5p_gpio_bank mp0_6; - struct s5p_gpio_bank mp0_7; - struct s5p_gpio_bank mp1_0; - struct s5p_gpio_bank mp1_1; - struct s5p_gpio_bank mp1_2; - struct s5p_gpio_bank mp1_3; - struct s5p_gpio_bank mp1_4; - struct s5p_gpio_bank mp1_5; - struct s5p_gpio_bank mp1_6; - struct s5p_gpio_bank mp1_7; - struct s5p_gpio_bank mp1_8; - struct s5p_gpio_bank mp2_0; - struct s5p_gpio_bank mp2_1; - struct s5p_gpio_bank mp2_2; - struct s5p_gpio_bank mp2_3; - struct s5p_gpio_bank mp2_4; - struct s5p_gpio_bank mp2_5; - struct s5p_gpio_bank mp2_6; - struct s5p_gpio_bank mp2_7; - struct s5p_gpio_bank mp2_8; - struct s5p_gpio_bank res1[48]; - struct s5p_gpio_bank h0; - struct s5p_gpio_bank h1; - struct s5p_gpio_bank h2; - struct s5p_gpio_bank h3; +enum s5pc110_gpio_pin { + S5PC110_GPIO_A00, + S5PC110_GPIO_A01, + S5PC110_GPIO_A02, + S5PC110_GPIO_A03, + S5PC110_GPIO_A04, + S5PC110_GPIO_A05, + S5PC110_GPIO_A06, + S5PC110_GPIO_A07, + S5PC110_GPIO_A10, + S5PC110_GPIO_A11, + S5PC110_GPIO_A12, + S5PC110_GPIO_A13, + S5PC110_GPIO_A14, + S5PC110_GPIO_A15, + S5PC110_GPIO_A16, + S5PC110_GPIO_A17, + S5PC110_GPIO_B0, + S5PC110_GPIO_B1, + S5PC110_GPIO_B2, + S5PC110_GPIO_B3, + S5PC110_GPIO_B4, + S5PC110_GPIO_B5, + S5PC110_GPIO_B6, + S5PC110_GPIO_B7, + S5PC110_GPIO_C00, + S5PC110_GPIO_C01, + S5PC110_GPIO_C02, + S5PC110_GPIO_C03, + S5PC110_GPIO_C04, + S5PC110_GPIO_C05, + S5PC110_GPIO_C06, + S5PC110_GPIO_C07, + S5PC110_GPIO_C10, + S5PC110_GPIO_C11, + S5PC110_GPIO_C12, + S5PC110_GPIO_C13, + S5PC110_GPIO_C14, + S5PC110_GPIO_C15, + S5PC110_GPIO_C16, + S5PC110_GPIO_C17, + S5PC110_GPIO_D00, + S5PC110_GPIO_D01, + S5PC110_GPIO_D02, + S5PC110_GPIO_D03, + S5PC110_GPIO_D04, + S5PC110_GPIO_D05, + S5PC110_GPIO_D06, + S5PC110_GPIO_D07, + S5PC110_GPIO_D10, + S5PC110_GPIO_D11, + S5PC110_GPIO_D12, + S5PC110_GPIO_D13, + S5PC110_GPIO_D14, + S5PC110_GPIO_D15, + S5PC110_GPIO_D16, + S5PC110_GPIO_D17, + S5PC110_GPIO_E00, + S5PC110_GPIO_E01, + S5PC110_GPIO_E02, + S5PC110_GPIO_E03, + S5PC110_GPIO_E04, + S5PC110_GPIO_E05, + S5PC110_GPIO_E06, + S5PC110_GPIO_E07, + S5PC110_GPIO_E10, + S5PC110_GPIO_E11, + S5PC110_GPIO_E12, + S5PC110_GPIO_E13, + S5PC110_GPIO_E14, + S5PC110_GPIO_E15, + S5PC110_GPIO_E16, + S5PC110_GPIO_E17, + S5PC110_GPIO_F00, + S5PC110_GPIO_F01, + S5PC110_GPIO_F02, + S5PC110_GPIO_F03, + S5PC110_GPIO_F04, + S5PC110_GPIO_F05, + S5PC110_GPIO_F06, + S5PC110_GPIO_F07, + S5PC110_GPIO_F10, + S5PC110_GPIO_F11, + S5PC110_GPIO_F12, + S5PC110_GPIO_F13, + S5PC110_GPIO_F14, + S5PC110_GPIO_F15, + S5PC110_GPIO_F16, + S5PC110_GPIO_F17, + S5PC110_GPIO_F20, + S5PC110_GPIO_F21, + S5PC110_GPIO_F22, + S5PC110_GPIO_F23, + S5PC110_GPIO_F24, + S5PC110_GPIO_F25, + S5PC110_GPIO_F26, + S5PC110_GPIO_F27, + S5PC110_GPIO_F30, + S5PC110_GPIO_F31, + S5PC110_GPIO_F32, + S5PC110_GPIO_F33, + S5PC110_GPIO_F34, + S5PC110_GPIO_F35, + S5PC110_GPIO_F36, + S5PC110_GPIO_F37, + S5PC110_GPIO_G00, + S5PC110_GPIO_G01, + S5PC110_GPIO_G02, + S5PC110_GPIO_G03, + S5PC110_GPIO_G04, + S5PC110_GPIO_G05, + S5PC110_GPIO_G06, + S5PC110_GPIO_G07, + S5PC110_GPIO_G10, + S5PC110_GPIO_G11, + S5PC110_GPIO_G12, + S5PC110_GPIO_G13, + S5PC110_GPIO_G14, + S5PC110_GPIO_G15, + S5PC110_GPIO_G16, + S5PC110_GPIO_G17, + S5PC110_GPIO_G20, + S5PC110_GPIO_G21, + S5PC110_GPIO_G22, + S5PC110_GPIO_G23, + S5PC110_GPIO_G24, + S5PC110_GPIO_G25, + S5PC110_GPIO_G26, + S5PC110_GPIO_G27, + S5PC110_GPIO_G30, + S5PC110_GPIO_G31, + S5PC110_GPIO_G32, + S5PC110_GPIO_G33, + S5PC110_GPIO_G34, + S5PC110_GPIO_G35, + S5PC110_GPIO_G36, + S5PC110_GPIO_G37, + S5PC110_GPIO_I0, + S5PC110_GPIO_I1, + S5PC110_GPIO_I2, + S5PC110_GPIO_I3, + S5PC110_GPIO_I4, + S5PC110_GPIO_I5, + S5PC110_GPIO_I6, + S5PC110_GPIO_I7, + S5PC110_GPIO_J00, + S5PC110_GPIO_J01, + S5PC110_GPIO_J02, + S5PC110_GPIO_J03, + S5PC110_GPIO_J04, + S5PC110_GPIO_J05, + S5PC110_GPIO_J06, + S5PC110_GPIO_J07, + S5PC110_GPIO_J10, + S5PC110_GPIO_J11, + S5PC110_GPIO_J12, + S5PC110_GPIO_J13, + S5PC110_GPIO_J14, + S5PC110_GPIO_J15, + S5PC110_GPIO_J16, + S5PC110_GPIO_J17, + S5PC110_GPIO_J20, + S5PC110_GPIO_J21, + S5PC110_GPIO_J22, + S5PC110_GPIO_J23, + S5PC110_GPIO_J24, + S5PC110_GPIO_J25, + S5PC110_GPIO_J26, + S5PC110_GPIO_J27, + S5PC110_GPIO_J30, + S5PC110_GPIO_J31, + S5PC110_GPIO_J32, + S5PC110_GPIO_J33, + S5PC110_GPIO_J34, + S5PC110_GPIO_J35, + S5PC110_GPIO_J36, + S5PC110_GPIO_J37, + S5PC110_GPIO_J40, + S5PC110_GPIO_J41, + S5PC110_GPIO_J42, + S5PC110_GPIO_J43, + S5PC110_GPIO_J44, + S5PC110_GPIO_J45, + S5PC110_GPIO_J46, + S5PC110_GPIO_J47, + S5PC110_GPIO_MP010, + S5PC110_GPIO_MP011, + S5PC110_GPIO_MP012, + S5PC110_GPIO_MP013, + S5PC110_GPIO_MP014, + S5PC110_GPIO_MP015, + S5PC110_GPIO_MP016, + S5PC110_GPIO_MP017, + S5PC110_GPIO_MP020, + S5PC110_GPIO_MP021, + S5PC110_GPIO_MP022, + S5PC110_GPIO_MP023, + S5PC110_GPIO_MP024, + S5PC110_GPIO_MP025, + S5PC110_GPIO_MP026, + S5PC110_GPIO_MP027, + S5PC110_GPIO_MP030, + S5PC110_GPIO_MP031, + S5PC110_GPIO_MP032, + S5PC110_GPIO_MP033, + S5PC110_GPIO_MP034, + S5PC110_GPIO_MP035, + S5PC110_GPIO_MP036, + S5PC110_GPIO_MP037, + S5PC110_GPIO_MP040, + S5PC110_GPIO_MP041, + S5PC110_GPIO_MP042, + S5PC110_GPIO_MP043, + S5PC110_GPIO_MP044, + S5PC110_GPIO_MP045, + S5PC110_GPIO_MP046, + S5PC110_GPIO_MP047, + S5PC110_GPIO_MP050, + S5PC110_GPIO_MP051, + S5PC110_GPIO_MP052, + S5PC110_GPIO_MP053, + S5PC110_GPIO_MP054, + S5PC110_GPIO_MP055, + S5PC110_GPIO_MP056, + S5PC110_GPIO_MP057, + S5PC110_GPIO_MP060, + S5PC110_GPIO_MP061, + S5PC110_GPIO_MP062, + S5PC110_GPIO_MP063, + S5PC110_GPIO_MP064, + S5PC110_GPIO_MP065, + S5PC110_GPIO_MP066, + S5PC110_GPIO_MP067, + S5PC110_GPIO_MP070, + S5PC110_GPIO_MP071, + S5PC110_GPIO_MP072, + S5PC110_GPIO_MP073, + S5PC110_GPIO_MP074, + S5PC110_GPIO_MP075, + S5PC110_GPIO_MP076, + S5PC110_GPIO_MP077, + S5PC110_GPIO_MP100, + S5PC110_GPIO_MP101, + S5PC110_GPIO_MP102, + S5PC110_GPIO_MP103, + S5PC110_GPIO_MP104, + S5PC110_GPIO_MP105, + S5PC110_GPIO_MP106, + S5PC110_GPIO_MP107, + S5PC110_GPIO_MP110, + S5PC110_GPIO_MP111, + S5PC110_GPIO_MP112, + S5PC110_GPIO_MP113, + S5PC110_GPIO_MP114, + S5PC110_GPIO_MP115, + S5PC110_GPIO_MP116, + S5PC110_GPIO_MP117, + S5PC110_GPIO_MP120, + S5PC110_GPIO_MP121, + S5PC110_GPIO_MP122, + S5PC110_GPIO_MP123, + S5PC110_GPIO_MP124, + S5PC110_GPIO_MP125, + S5PC110_GPIO_MP126, + S5PC110_GPIO_MP127, + S5PC110_GPIO_MP130, + S5PC110_GPIO_MP131, + S5PC110_GPIO_MP132, + S5PC110_GPIO_MP133, + S5PC110_GPIO_MP134, + S5PC110_GPIO_MP135, + S5PC110_GPIO_MP136, + S5PC110_GPIO_MP137, + S5PC110_GPIO_MP140, + S5PC110_GPIO_MP141, + S5PC110_GPIO_MP142, + S5PC110_GPIO_MP143, + S5PC110_GPIO_MP144, + S5PC110_GPIO_MP145, + S5PC110_GPIO_MP146, + S5PC110_GPIO_MP147, + S5PC110_GPIO_MP150, + S5PC110_GPIO_MP151, + S5PC110_GPIO_MP152, + S5PC110_GPIO_MP153, + S5PC110_GPIO_MP154, + S5PC110_GPIO_MP155, + S5PC110_GPIO_MP156, + S5PC110_GPIO_MP157, + S5PC110_GPIO_MP160, + S5PC110_GPIO_MP161, + S5PC110_GPIO_MP162, + S5PC110_GPIO_MP163, + S5PC110_GPIO_MP164, + S5PC110_GPIO_MP165, + S5PC110_GPIO_MP166, + S5PC110_GPIO_MP167, + S5PC110_GPIO_MP170, + S5PC110_GPIO_MP171, + S5PC110_GPIO_MP172, + S5PC110_GPIO_MP173, + S5PC110_GPIO_MP174, + S5PC110_GPIO_MP175, + S5PC110_GPIO_MP176, + S5PC110_GPIO_MP177, + S5PC110_GPIO_MP180, + S5PC110_GPIO_MP181, + S5PC110_GPIO_MP182, + S5PC110_GPIO_MP183, + S5PC110_GPIO_MP184, + S5PC110_GPIO_MP185, + S5PC110_GPIO_MP186, + S5PC110_GPIO_MP187, + S5PC110_GPIO_MP200, + S5PC110_GPIO_MP201, + S5PC110_GPIO_MP202, + S5PC110_GPIO_MP203, + S5PC110_GPIO_MP204, + S5PC110_GPIO_MP205, + S5PC110_GPIO_MP206, + S5PC110_GPIO_MP207, + S5PC110_GPIO_MP210, + S5PC110_GPIO_MP211, + S5PC110_GPIO_MP212, + S5PC110_GPIO_MP213, + S5PC110_GPIO_MP214, + S5PC110_GPIO_MP215, + S5PC110_GPIO_MP216, + S5PC110_GPIO_MP217, + S5PC110_GPIO_MP220, + S5PC110_GPIO_MP221, + S5PC110_GPIO_MP222, + S5PC110_GPIO_MP223, + S5PC110_GPIO_MP224, + S5PC110_GPIO_MP225, + S5PC110_GPIO_MP226, + S5PC110_GPIO_MP227, + S5PC110_GPIO_MP230, + S5PC110_GPIO_MP231, + S5PC110_GPIO_MP232, + S5PC110_GPIO_MP233, + S5PC110_GPIO_MP234, + S5PC110_GPIO_MP235, + S5PC110_GPIO_MP236, + S5PC110_GPIO_MP237, + S5PC110_GPIO_MP240, + S5PC110_GPIO_MP241, + S5PC110_GPIO_MP242, + S5PC110_GPIO_MP243, + S5PC110_GPIO_MP244, + S5PC110_GPIO_MP245, + S5PC110_GPIO_MP246, + S5PC110_GPIO_MP247, + S5PC110_GPIO_MP250, + S5PC110_GPIO_MP251, + S5PC110_GPIO_MP252, + S5PC110_GPIO_MP253, + S5PC110_GPIO_MP254, + S5PC110_GPIO_MP255, + S5PC110_GPIO_MP256, + S5PC110_GPIO_MP257, + S5PC110_GPIO_MP260, + S5PC110_GPIO_MP261, + S5PC110_GPIO_MP262, + S5PC110_GPIO_MP263, + S5PC110_GPIO_MP264, + S5PC110_GPIO_MP265, + S5PC110_GPIO_MP266, + S5PC110_GPIO_MP267, + S5PC110_GPIO_MP270, + S5PC110_GPIO_MP271, + S5PC110_GPIO_MP272, + S5PC110_GPIO_MP273, + S5PC110_GPIO_MP274, + S5PC110_GPIO_MP275, + S5PC110_GPIO_MP276, + S5PC110_GPIO_MP277, + S5PC110_GPIO_MP280, + S5PC110_GPIO_MP281, + S5PC110_GPIO_MP282, + S5PC110_GPIO_MP283, + S5PC110_GPIO_MP284, + S5PC110_GPIO_MP285, + S5PC110_GPIO_MP286, + S5PC110_GPIO_MP287, + S5PC110_GPIO_RES, + S5PC110_GPIO_H00 = (S5PC110_GPIO_RES + (48 * 8)), + S5PC110_GPIO_H01, + S5PC110_GPIO_H02, + S5PC110_GPIO_H03, + S5PC110_GPIO_H04, + S5PC110_GPIO_H05, + S5PC110_GPIO_H06, + S5PC110_GPIO_H07, + S5PC110_GPIO_H10, + S5PC110_GPIO_H11, + S5PC110_GPIO_H12, + S5PC110_GPIO_H13, + S5PC110_GPIO_H14, + S5PC110_GPIO_H15, + S5PC110_GPIO_H16, + S5PC110_GPIO_H17, + S5PC110_GPIO_H20, + S5PC110_GPIO_H21, + S5PC110_GPIO_H22, + S5PC110_GPIO_H23, + S5PC110_GPIO_H24, + S5PC110_GPIO_H25, + S5PC110_GPIO_H26, + S5PC110_GPIO_H27, + S5PC110_GPIO_H30, + S5PC110_GPIO_H31, + S5PC110_GPIO_H32, + S5PC110_GPIO_H33, + S5PC110_GPIO_H34, + S5PC110_GPIO_H35, + S5PC110_GPIO_H36, + S5PC110_GPIO_H37, + + S5PC110_GPIO_MAX_PORT }; -/* functions */ -void s5p_gpio_cfg_pin(struct s5p_gpio_bank *bank, int gpio, int cfg); -void s5p_gpio_direction_output(struct s5p_gpio_bank *bank, int gpio, int en); -void s5p_gpio_direction_input(struct s5p_gpio_bank *bank, int gpio); -void s5p_gpio_set_value(struct s5p_gpio_bank *bank, int gpio, int en); -unsigned int s5p_gpio_get_value(struct s5p_gpio_bank *bank, int gpio); -void s5p_gpio_set_pull(struct s5p_gpio_bank *bank, int gpio, int mode); -void s5p_gpio_set_drv(struct s5p_gpio_bank *bank, int gpio, int mode); -void s5p_gpio_set_rate(struct s5p_gpio_bank *bank, int gpio, int mode); +struct gpio_info { + unsigned int reg_addr; /* Address of register for this part */ + unsigned int max_gpio; /* Maximum GPIO in this part */ +}; -/* GPIO pins per bank */ -#define GPIO_PER_BANK 8 +#define S5PC100_GPIO_NUM_PARTS 1 +static struct gpio_info s5pc100_gpio_data[S5PC100_GPIO_NUM_PARTS] = { + { S5PC100_GPIO_BASE, S5PC100_GPIO_MAX_PORT }, +}; -#define S5P_GPIO_PART_SHIFT (24) -#define S5P_GPIO_PART_MASK (0xff) -#define S5P_GPIO_BANK_SHIFT (8) -#define S5P_GPIO_BANK_MASK (0xffff) -#define S5P_GPIO_PIN_MASK (0xff) +#define S5PC110_GPIO_NUM_PARTS 1 +static struct gpio_info s5pc110_gpio_data[S5PC110_GPIO_NUM_PARTS] = { + { S5PC110_GPIO_BASE, S5PC110_GPIO_MAX_PORT }, +}; -#define S5P_GPIO_SET_PART(x) \ - (((x) & S5P_GPIO_PART_MASK) << S5P_GPIO_PART_SHIFT) +static inline struct gpio_info *get_gpio_data(void) +{ + if (cpu_is_s5pc100()) + return s5pc100_gpio_data; + else if (cpu_is_s5pc110()) + return s5pc110_gpio_data; -#define S5P_GPIO_GET_PART(x) \ - (((x) >> S5P_GPIO_PART_SHIFT) & S5P_GPIO_PART_MASK) + return NULL; +} -#define S5P_GPIO_SET_PIN(x) \ - ((x) & S5P_GPIO_PIN_MASK) +static inline unsigned int get_bank_num(void) +{ + if (cpu_is_s5pc100()) + return S5PC100_GPIO_NUM_PARTS; + else if (cpu_is_s5pc110()) + return S5PC110_GPIO_NUM_PARTS; -#define S5PC100_SET_BANK(bank) \ - (((unsigned)&(((struct s5pc100_gpio *) \ - S5PC100_GPIO_BASE)->bank) - S5PC100_GPIO_BASE) \ - & S5P_GPIO_BANK_MASK) << S5P_GPIO_BANK_SHIFT) + return 0; +} -#define S5PC110_SET_BANK(bank) \ - ((((unsigned)&(((struct s5pc110_gpio *) \ - S5PC110_GPIO_BASE)->bank) - S5PC110_GPIO_BASE) \ - & S5P_GPIO_BANK_MASK) << S5P_GPIO_BANK_SHIFT) +/* + * This structure helps mapping symbolic GPIO names into indices from + * exynos5_gpio_pin/exynos5420_gpio_pin enums. + * + * By convention, symbolic GPIO name is defined as follows: + * + * g[p]<bank><set><bit>, where + * p is optional + * <bank> - a single character bank name, as defined by the SOC + * <set> - a single digit set number + * <bit> - bit number within the set (in 0..7 range). + * + * <set><bit> essentially form an octal number of the GPIO pin within the bank + * space. On the 5420 architecture some banks' sets do not start not from zero + * ('d' starts from 1 and 'j' starts from 4). To compensate for that and + * maintain flat number space withoout holes, those banks use offsets to be + * deducted from the pin number. + */ +struct gpio_name_num_table { + char bank; /* bank name symbol */ + u8 bank_size; /* total number of pins in the bank */ + char bank_offset; /* offset of the first bank's pin */ + unsigned int base; /* index of the first bank's pin in the enum */ +}; -#define s5pc100_gpio_get(bank, pin) \ - (S5P_GPIO_SET_PART(0) | \ - S5PC100_SET_BANK(bank) | \ - S5P_GPIO_SET_PIN(pin)) +#define GPIO_PER_BANK 8 +#define GPIO_ENTRY(name, base, top, offset) { name, top - base, offset, base } +static const struct gpio_name_num_table s5pc100_gpio_table[] = { + GPIO_ENTRY('a', S5PC100_GPIO_A00, S5PC100_GPIO_B0, 0), + GPIO_ENTRY('b', S5PC100_GPIO_B0, S5PC100_GPIO_C0, 0), + GPIO_ENTRY('c', S5PC100_GPIO_C0, S5PC100_GPIO_D0, 0), + GPIO_ENTRY('d', S5PC100_GPIO_D0, S5PC100_GPIO_E00, 0), + GPIO_ENTRY('e', S5PC100_GPIO_E00, S5PC100_GPIO_F00, 0), + GPIO_ENTRY('f', S5PC100_GPIO_F00, S5PC100_GPIO_G00, 0), + GPIO_ENTRY('g', S5PC100_GPIO_G00, S5PC100_GPIO_I0, 0), + GPIO_ENTRY('i', S5PC100_GPIO_I0, S5PC100_GPIO_J00, 0), + GPIO_ENTRY('j', S5PC100_GPIO_J00, S5PC100_GPIO_K00, 0), + GPIO_ENTRY('k', S5PC100_GPIO_K00, S5PC100_GPIO_L00, 0), + GPIO_ENTRY('l', S5PC100_GPIO_L00, S5PC100_GPIO_H00, 0), + GPIO_ENTRY('h', S5PC100_GPIO_H00, S5PC100_GPIO_MAX_PORT, 0), + { 0 } +}; -#define s5pc110_gpio_get(bank, pin) \ - (S5P_GPIO_SET_PART(0) | \ - S5PC110_SET_BANK(bank) | \ - S5P_GPIO_SET_PIN(pin)) +static const struct gpio_name_num_table s5pc110_gpio_table[] = { + GPIO_ENTRY('a', S5PC110_GPIO_A00, S5PC110_GPIO_B0, 0), + GPIO_ENTRY('b', S5PC110_GPIO_B0, S5PC110_GPIO_C00, 0), + GPIO_ENTRY('c', S5PC110_GPIO_C00, S5PC110_GPIO_D00, 0), + GPIO_ENTRY('d', S5PC110_GPIO_D00, S5PC110_GPIO_E00, 0), + GPIO_ENTRY('e', S5PC110_GPIO_E00, S5PC110_GPIO_F00, 0), + GPIO_ENTRY('f', S5PC110_GPIO_F00, S5PC110_GPIO_G00, 0), + GPIO_ENTRY('g', S5PC110_GPIO_G00, S5PC110_GPIO_I0, 0), + GPIO_ENTRY('i', S5PC110_GPIO_I0, S5PC110_GPIO_J00, 0), + GPIO_ENTRY('j', S5PC110_GPIO_J00, S5PC110_GPIO_MP010, 0), + GPIO_ENTRY('h', S5PC110_GPIO_H00, S5PC110_GPIO_MAX_PORT, 0), + { 0 } +}; -static inline unsigned int s5p_gpio_base(int nr) -{ - return samsung_get_base_gpio(); -} +/* functions */ +void gpio_cfg_pin(int gpio, int cfg); +void gpio_set_pull(int gpio, int mode); +void gpio_set_drv(int gpio, int mode); +int gpio_direction_output(unsigned gpio, int value); +int gpio_set_value(unsigned gpio, int value); +int gpio_get_value(unsigned gpio); +void gpio_set_rate(int gpio, int mode); +struct s5p_gpio_bank *s5p_gpio_get_bank(unsigned gpio); +int s5p_gpio_get_pin(unsigned gpio); + +/* GPIO pins per bank */ +#define GPIO_PER_BANK 8 #endif /* Pin configurations */ -#define GPIO_INPUT 0x0 -#define GPIO_OUTPUT 0x1 -#define GPIO_IRQ 0xf -#define GPIO_FUNC(x) (x) +#define S5P_GPIO_INPUT 0x0 +#define S5P_GPIO_OUTPUT 0x1 +#define S5P_GPIO_IRQ 0xf +#define S5P_GPIO_FUNC(x) (x) /* Pull mode */ -#define GPIO_PULL_NONE 0x0 -#define GPIO_PULL_DOWN 0x1 -#define GPIO_PULL_UP 0x2 +#define S5P_GPIO_PULL_NONE 0x0 +#define S5P_GPIO_PULL_DOWN 0x1 +#define S5P_GPIO_PULL_UP 0x2 /* Drive Strength level */ -#define GPIO_DRV_1X 0x0 -#define GPIO_DRV_3X 0x1 -#define GPIO_DRV_2X 0x2 -#define GPIO_DRV_4X 0x3 -#define GPIO_DRV_FAST 0x0 -#define GPIO_DRV_SLOW 0x1 +#define S5P_GPIO_DRV_1X 0x0 +#define S5P_GPIO_DRV_3X 0x1 +#define S5P_GPIO_DRV_2X 0x2 +#define S5P_GPIO_DRV_4X 0x3 +#define S5P_GPIO_DRV_FAST 0x0 +#define S5P_GPIO_DRV_SLOW 0x1 #endif diff --git a/arch/arm/include/asm/arch-tegra/gpio.h b/arch/arm/include/asm/arch-tegra/gpio.h index d97190dd7c..44cd455699 100644 --- a/arch/arm/include/asm/arch-tegra/gpio.h +++ b/arch/arm/include/asm/arch-tegra/gpio.h @@ -14,11 +14,31 @@ #define GPIO_FULLPORT(x) ((x) >> 3) #define GPIO_BIT(x) ((x) & 0x7) +enum tegra_gpio_init { + TEGRA_GPIO_INIT_IN, + TEGRA_GPIO_INIT_OUT0, + TEGRA_GPIO_INIT_OUT1, +}; + +struct tegra_gpio_config { + u32 gpio:16; + u32 init:2; +}; + /* * Tegra-specific GPIO API */ +/** + * Configure a list of GPIOs + * + * @param config List of GPIO configurations + * @param len Number of config items in list + */ +void gpio_config_table(const struct tegra_gpio_config *config, int len); + void gpio_info(void); #define gpio_status() gpio_info() + #endif /* TEGRA_GPIO_H_ */ diff --git a/arch/arm/include/asm/arch-tegra/pinmux.h b/arch/arm/include/asm/arch-tegra/pinmux.h index 035159d665..da477697bf 100644 --- a/arch/arm/include/asm/arch-tegra/pinmux.h +++ b/arch/arm/include/asm/arch-tegra/pinmux.h @@ -80,6 +80,11 @@ struct pmux_pingrp_config { #endif }; +#if !defined(CONFIG_TEGRA20) && !defined(CONFIG_TEGRA30) +/* Set the pinmux CLAMP_INPUTS_WHEN_TRISTATED bit */ +void pinmux_set_tristate_input_clamping(void); +#endif + /* Set the mux function for a pin group */ void pinmux_set_func(enum pmux_pingrp pin, enum pmux_func func); diff --git a/arch/arm/include/asm/arch-tegra/tegra_mmc.h b/arch/arm/include/asm/arch-tegra/tegra_mmc.h index 310bbd7df9..84e7b5553d 100644 --- a/arch/arm/include/asm/arch-tegra/tegra_mmc.h +++ b/arch/arm/include/asm/arch-tegra/tegra_mmc.h @@ -14,8 +14,6 @@ /* for mmc_config definition */ #include <mmc.h> -#define MAX_HOSTS 4 /* Max number of 'hosts'/controllers */ - #ifndef __ASSEMBLY__ struct tegra_mmc { unsigned int sysad; /* _SYSTEM_ADDRESS_0 */ diff --git a/arch/arm/include/asm/arch-tegra/usb.h b/arch/arm/include/asm/arch-tegra/usb.h index ceb7bcd9cf..c817088fa5 100644 --- a/arch/arm/include/asm/arch-tegra/usb.h +++ b/arch/arm/include/asm/arch-tegra/usb.h @@ -349,6 +349,8 @@ struct usb_ctlr { /* USB3_IF_USB_PHY_VBUS_SENSORS_0 */ #define VBUS_VLD_STS (1 << 26) +#define VBUS_B_SESS_VLD_SW_VALUE (1 << 12) +#define VBUS_B_SESS_VLD_SW_EN (1 << 11) /* Setup USB on the board */ int usb_process_devicetree(const void *blob); diff --git a/arch/arm/include/asm/arch-tegra114/pinmux.h b/arch/arm/include/asm/arch-tegra114/pinmux.h index c1cb3ef16b..b86562ac6d 100644 --- a/arch/arm/include/asm/arch-tegra114/pinmux.h +++ b/arch/arm/include/asm/arch-tegra114/pinmux.h @@ -231,6 +231,7 @@ enum pmux_drvgrp { }; enum pmux_func { + PMUX_FUNC_DEFAULT, PMUX_FUNC_BLINK, PMUX_FUNC_CEC, PMUX_FUNC_CLDVFS, diff --git a/arch/arm/include/asm/arch-tegra124/pinmux.h b/arch/arm/include/asm/arch-tegra124/pinmux.h index c49801c21d..1884935a57 100644 --- a/arch/arm/include/asm/arch-tegra124/pinmux.h +++ b/arch/arm/include/asm/arch-tegra124/pinmux.h @@ -247,6 +247,7 @@ enum pmux_drvgrp { }; enum pmux_func { + PMUX_FUNC_DEFAULT, PMUX_FUNC_BLINK, PMUX_FUNC_CCLA, PMUX_FUNC_CEC, diff --git a/arch/arm/include/asm/arch-tegra20/pinmux.h b/arch/arm/include/asm/arch-tegra20/pinmux.h index 11c0104ff3..f7bc97fe5f 100644 --- a/arch/arm/include/asm/arch-tegra20/pinmux.h +++ b/arch/arm/include/asm/arch-tegra20/pinmux.h @@ -166,6 +166,7 @@ enum pmux_pingrp { * purely a convenience. The translation is done through a table search. */ enum pmux_func { + PMUX_FUNC_DEFAULT, PMUX_FUNC_AHB_CLK, PMUX_FUNC_APB_CLK, PMUX_FUNC_AUDIO_SYNC, diff --git a/arch/arm/include/asm/arch-tegra30/pinmux.h b/arch/arm/include/asm/arch-tegra30/pinmux.h index 6d83061dc1..a42e00990f 100644 --- a/arch/arm/include/asm/arch-tegra30/pinmux.h +++ b/arch/arm/include/asm/arch-tegra30/pinmux.h @@ -306,6 +306,7 @@ enum pmux_drvgrp { }; enum pmux_func { + PMUX_FUNC_DEFAULT, PMUX_FUNC_BLINK, PMUX_FUNC_CEC, PMUX_FUNC_CLK_12M_OUT, diff --git a/arch/arm/include/asm/imx-common/iomux-v3.h b/arch/arm/include/asm/imx-common/iomux-v3.h index dec11a1330..cca920b28e 100644 --- a/arch/arm/include/asm/imx-common/iomux-v3.h +++ b/arch/arm/include/asm/imx-common/iomux-v3.h @@ -111,6 +111,11 @@ typedef u64 iomux_v3_cfg_t; #define PAD_CTL_DSE_40ohm (6 << 3) #define PAD_CTL_DSE_34ohm (7 << 3) +#if defined CONFIG_MX6SL +#define PAD_CTL_LVE (1 << 1) +#define PAD_CTL_LVE_BIT (1 << 22) +#endif + #elif defined(CONFIG_VF610) #define PAD_MUX_MODE_SHIFT 20 diff --git a/arch/arm/include/asm/imx-common/video.h b/arch/arm/include/asm/imx-common/video.h new file mode 100644 index 0000000000..2d948508d5 --- /dev/null +++ b/arch/arm/include/asm/imx-common/video.h @@ -0,0 +1,24 @@ +/* + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __IMX_VIDEO_H_ +#define __IMX_VIDEO_H_ + +#include <linux/fb.h> +#include <ipu_pixfmt.h> + +struct display_info_t { + int bus; + int addr; + int pixfmt; + int (*detect)(struct display_info_t const *dev); + void (*enable)(struct display_info_t const *dev); + struct fb_videomode mode; +}; + +#ifdef CONFIG_IMX_HDMI +extern int detect_hdmi(struct display_info_t const *dev); +#endif + +#endif diff --git a/arch/arm/lib/Makefile b/arch/arm/lib/Makefile index e035d6acc0..585f1f781b 100644 --- a/arch/arm/lib/Makefile +++ b/arch/arm/lib/Makefile @@ -11,7 +11,7 @@ lib-$(CONFIG_USE_PRIVATE_LIBGCC) += _ashldi3.o _ashrdi3.o _divsi3.o \ ifdef CONFIG_ARM64 obj-y += crt0_64.o else -obj-y += crt0.o +obj-y += vectors.o crt0.o endif ifndef CONFIG_SPL_BUILD diff --git a/arch/arm/lib/cache.c b/arch/arm/lib/cache.c index 6cc136aa3c..4f6b9f01cb 100644 --- a/arch/arm/lib/cache.c +++ b/arch/arm/lib/cache.c @@ -12,16 +12,23 @@ void __flush_cache(unsigned long start, unsigned long size) { #if defined(CONFIG_ARM1136) - void arm1136_cache_flush(void); - arm1136_cache_flush(); +#if !defined(CONFIG_SYS_ICACHE_OFF) + asm("mcr p15, 0, r1, c7, c5, 0"); /* invalidate I cache */ #endif + +#if !defined(CONFIG_SYS_DCACHE_OFF) + asm("mcr p15, 0, r1, c7, c14, 0"); /* Clean+invalidate D cache */ +#endif + +#endif /* CONFIG_ARM1136 */ + #ifdef CONFIG_ARM926EJS /* test and clean, page 2-23 of arm926ejs manual */ asm("0: mrc p15, 0, r15, c7, c10, 3\n\t" "bne 0b\n" : : : "memory"); /* disable write buffer as well (page 2-22) */ asm("mcr p15, 0, %0, c7, c10, 4" : : "r" (0)); -#endif +#endif /* CONFIG_ARM926EJS */ return; } void flush_cache(unsigned long start, unsigned long size) diff --git a/arch/arm/lib/vectors.S b/arch/arm/lib/vectors.S new file mode 100644 index 0000000000..d68cc477dc --- /dev/null +++ b/arch/arm/lib/vectors.S @@ -0,0 +1,291 @@ +/* + * vectors - Generic ARM exception table code + * + * Copyright (c) 1998 Dan Malek <dmalek@jlc.net> + * Copyright (c) 1999 Magnus Damm <kieraypc01.p.y.kie.era.ericsson.se> + * Copyright (c) 2000 Wolfgang Denk <wd@denx.de> + * Copyright (c) 2001 Alex Züpke <azu@sysgo.de> + * Copyright (c) 2001 Marius Gröger <mag@sysgo.de> + * Copyright (c) 2002 Alex Züpke <azu@sysgo.de> + * Copyright (c) 2002 Gary Jennejohn <garyj@denx.de> + * Copyright (c) 2002 Kyle Harris <kharris@nexus-tech.net> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + ************************************************************************* + * + * Symbol _start is referenced elsewhere, so make it global + * + ************************************************************************* + */ + +.globl _start + +/* + ************************************************************************* + * + * Vectors have their own section so linker script can map them easily + * + ************************************************************************* + */ + + .section ".vectors", "x" + +/* + ************************************************************************* + * + * Exception vectors as described in ARM reference manuals + * + * Uses indirect branch to allow reaching handlers anywhere in memory. + * + ************************************************************************* + */ + +_start: + +#ifdef CONFIG_SYS_DV_NOR_BOOT_CFG + .word CONFIG_SYS_DV_NOR_BOOT_CFG +#endif + +_start: + ldr pc, _reset + ldr pc, _undefined_instruction + ldr pc, _software_interrupt + ldr pc, _prefetch_abort + ldr pc, _data_abort + ldr pc, _not_used + ldr pc, _irq + ldr pc, _fiq + +/* + ************************************************************************* + * + * Indirect vectors table + * + * Symbols referenced here must be defined somewhere else + * + ************************************************************************* + */ + + .globl _undefined_instruction + .globl _software_interrupt + .globl _prefetch_abort + .globl _data_abort + .globl _not_used + .globl _irq + .globl _fiq + +_reset: .word reset +_undefined_instruction: .word undefined_instruction +_software_interrupt: .word software_interrupt +_prefetch_abort: .word prefetch_abort +_data_abort: .word data_abort +_not_used: .word not_used +_irq: .word irq +_fiq: .word fiq + + .balignl 16,0xdeadbeef + +/* + ************************************************************************* + * + * Interrupt handling + * + ************************************************************************* + */ + +/* SPL interrupt handling: just hang */ + +#ifdef CONFIG_SPL_BUILD + + .align 5 +undefined_instruction: +software_interrupt: +prefetch_abort: +data_abort: +not_used: +irq: +fiq: + +1: + bl 1b /* hang and never return */ + +#else /* !CONFIG_SPL_BUILD */ + +/* IRQ stack memory (calculated at run-time) + 8 bytes */ +.globl IRQ_STACK_START_IN +IRQ_STACK_START_IN: + .word 0x0badc0de + +#ifdef CONFIG_USE_IRQ +/* IRQ stack memory (calculated at run-time) */ +.globl IRQ_STACK_START +IRQ_STACK_START: + .word 0x0badc0de + +/* IRQ stack memory (calculated at run-time) */ +.globl FIQ_STACK_START +FIQ_STACK_START: + .word 0x0badc0de + +#endif /* CONFIG_USE_IRQ */ + +@ +@ IRQ stack frame. +@ +#define S_FRAME_SIZE 72 + +#define S_OLD_R0 68 +#define S_PSR 64 +#define S_PC 60 +#define S_LR 56 +#define S_SP 52 + +#define S_IP 48 +#define S_FP 44 +#define S_R10 40 +#define S_R9 36 +#define S_R8 32 +#define S_R7 28 +#define S_R6 24 +#define S_R5 20 +#define S_R4 16 +#define S_R3 12 +#define S_R2 8 +#define S_R1 4 +#define S_R0 0 + +#define MODE_SVC 0x13 +#define I_BIT 0x80 + +/* + * use bad_save_user_regs for abort/prefetch/undef/swi ... + * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling + */ + + .macro bad_save_user_regs + @ carve out a frame on current user stack + sub sp, sp, #S_FRAME_SIZE + stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12 + ldr r2, IRQ_STACK_START_IN + @ get values for "aborted" pc and cpsr (into parm regs) + ldmia r2, {r2 - r3} + add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack + add r5, sp, #S_SP + mov r1, lr + stmia r5, {r0 - r3} @ save sp_SVC, lr_SVC, pc, cpsr + mov r0, sp @ save current stack into r0 (param register) + .endm + + .macro irq_save_user_regs + sub sp, sp, #S_FRAME_SIZE + stmia sp, {r0 - r12} @ Calling r0-r12 + @ !!!! R8 NEEDS to be saved !!!! a reserved stack spot would be good. + add r8, sp, #S_PC + stmdb r8, {sp, lr}^ @ Calling SP, LR + str lr, [r8, #0] @ Save calling PC + mrs r6, spsr + str r6, [r8, #4] @ Save CPSR + str r0, [r8, #8] @ Save OLD_R0 + mov r0, sp + .endm + + .macro irq_restore_user_regs + ldmia sp, {r0 - lr}^ @ Calling r0 - lr + mov r0, r0 + ldr lr, [sp, #S_PC] @ Get PC + add sp, sp, #S_FRAME_SIZE + subs pc, lr, #4 @ return & move spsr_svc into cpsr + .endm + + .macro get_bad_stack + ldr r13, IRQ_STACK_START_IN @ setup our mode stack + + str lr, [r13] @ save caller lr in position 0 of saved stack + mrs lr, spsr @ get the spsr + str lr, [r13, #4] @ save spsr in position 1 of saved stack + mov r13, #MODE_SVC @ prepare SVC-Mode + @ msr spsr_c, r13 + msr spsr, r13 @ switch modes, make sure moves will execute + mov lr, pc @ capture return pc + movs pc, lr @ jump to next instruction & switch modes. + .endm + + .macro get_irq_stack @ setup IRQ stack + ldr sp, IRQ_STACK_START + .endm + + .macro get_fiq_stack @ setup FIQ stack + ldr sp, FIQ_STACK_START + .endm + +/* + * exception handlers + */ + + .align 5 +undefined_instruction: + get_bad_stack + bad_save_user_regs + bl do_undefined_instruction + + .align 5 +software_interrupt: + get_bad_stack + bad_save_user_regs + bl do_software_interrupt + + .align 5 +prefetch_abort: + get_bad_stack + bad_save_user_regs + bl do_prefetch_abort + + .align 5 +data_abort: + get_bad_stack + bad_save_user_regs + bl do_data_abort + + .align 5 +not_used: + get_bad_stack + bad_save_user_regs + bl do_not_used + +#ifdef CONFIG_USE_IRQ + + .align 5 +irq: + get_irq_stack + irq_save_user_regs + bl do_irq + irq_restore_user_regs + + .align 5 +fiq: + get_fiq_stack + /* someone ought to write a more effiction fiq_save_user_regs */ + irq_save_user_regs + bl do_fiq + irq_restore_user_regs + +#else + + .align 5 +irq: + get_bad_stack + bad_save_user_regs + bl do_irq + + .align 5 +fiq: + get_bad_stack + bad_save_user_regs + bl do_fiq + +#endif /* CONFIG_USE_IRQ */ + +#endif /* CONFIG_SPL_BUILD */ diff --git a/arch/powerpc/cpu/mpc85xx/Makefile b/arch/powerpc/cpu/mpc85xx/Makefile index 409478539e..ad26b432f1 100644 --- a/arch/powerpc/cpu/mpc85xx/Makefile +++ b/arch/powerpc/cpu/mpc85xx/Makefile @@ -44,6 +44,7 @@ obj-$(CONFIG_PPC_P5020) += p5020_ids.o obj-$(CONFIG_PPC_P5040) += p5040_ids.o obj-$(CONFIG_PPC_T4240) += t4240_ids.o obj-$(CONFIG_PPC_T4160) += t4240_ids.o +obj-$(CONFIG_PPC_T4080) += t4240_ids.o obj-$(CONFIG_PPC_B4420) += b4860_ids.o obj-$(CONFIG_PPC_B4860) += b4860_ids.o obj-$(CONFIG_PPC_T1040) += t1040_ids.o @@ -88,6 +89,7 @@ obj-$(CONFIG_PPC_P5020) += p5020_serdes.o obj-$(CONFIG_PPC_P5040) += p5040_serdes.o obj-$(CONFIG_PPC_T4240) += t4240_serdes.o obj-$(CONFIG_PPC_T4160) += t4240_serdes.o +obj-$(CONFIG_PPC_T4080) += t4240_serdes.o obj-$(CONFIG_PPC_B4420) += b4860_serdes.o obj-$(CONFIG_PPC_B4860) += b4860_serdes.o obj-$(CONFIG_BSC9132) += bsc9132_serdes.o diff --git a/arch/powerpc/cpu/mpc85xx/cmd_errata.c b/arch/powerpc/cpu/mpc85xx/cmd_errata.c index 9d8acd0aa1..3d37a7614f 100644 --- a/arch/powerpc/cpu/mpc85xx/cmd_errata.c +++ b/arch/powerpc/cpu/mpc85xx/cmd_errata.c @@ -299,6 +299,9 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) #ifdef CONFIG_SYS_FSL_ERRATUM_A007212 check_erratum_a007212(); #endif +#ifdef CONFIG_SYS_FSL_ERRATUM_A005434 + puts("Work-around for Erratum A-005434 enabled\n"); +#endif return 0; } diff --git a/arch/powerpc/cpu/mpc85xx/cpu.c b/arch/powerpc/cpu/mpc85xx/cpu.c index 12e8e10d48..684d4007e4 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu.c +++ b/arch/powerpc/cpu/mpc85xx/cpu.c @@ -77,6 +77,30 @@ int checkcpu (void) major = SVR_MAJ(svr); minor = SVR_MIN(svr); +#if defined(CONFIG_SYS_FSL_QORIQ_CHASSIS2) && defined(CONFIG_E6500) + if (SVR_SOC_VER(svr) == SVR_T4080) { + ccsr_rcpm_t *rcpm = + (void __iomem *)(CONFIG_SYS_FSL_CORENET_RCPM_ADDR); + + setbits_be32(&gur->devdisr2, FSL_CORENET_DEVDISR2_DTSEC1_6 || + FSL_CORENET_DEVDISR2_DTSEC1_9); + setbits_be32(&gur->devdisr3, FSL_CORENET_DEVDISR3_PCIE3); + setbits_be32(&gur->devdisr5, FSL_CORENET_DEVDISR5_DDR3); + + /* It needs SW to disable core4~7 as HW design sake on T4080 */ + for (i = 4; i < 8; i++) + cpu_disable(i); + + /* request core4~7 into PH20 state, prior to entering PCL10 + * state, all cores in cluster should be placed in PH20 state. + */ + setbits_be32(&rcpm->pcph20setr, 0xf0); + + /* put the 2nd cluster into PCL10 state */ + setbits_be32(&rcpm->clpcl10setr, 1 << 1); + } +#endif + if (cpu_numcores() > 1) { #ifndef CONFIG_MP puts("Unicore software on multiprocessor system!!\n" diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c index 36ef23232e..d6cf88555a 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c @@ -368,12 +368,12 @@ void fsl_erratum_a007212_workaround(void) } #endif -void cpu_init_f (void) +ulong cpu_init_f(void) { + ulong flag = 0; extern void m8560_cpm_reset (void); #ifdef CONFIG_SYS_DCSRBAR_PHYS ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - gd = (gd_t *)(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET); #endif #if defined(CONFIG_SECURE_BOOT) struct law_entry law; @@ -442,13 +442,14 @@ void cpu_init_f (void) #ifdef CONFIG_DEEP_SLEEP /* disable the console if boot from deep sleep */ if (in_be32(&gur->scrtsr[0]) & (1 << 3)) - gd->flags |= GD_FLG_SILENT | GD_FLG_DISABLE_CONSOLE; + flag = GD_FLG_SILENT | GD_FLG_DISABLE_CONSOLE; #endif #endif #ifdef CONFIG_SYS_FSL_ERRATUM_A007212 fsl_erratum_a007212_workaround(); #endif + return flag; } /* Implement a dummy function for those platforms w/o SERDES */ @@ -462,10 +463,17 @@ __attribute__((weak, alias("__fsl_serdes__init"))) void fsl_serdes_init(void); int enable_cluster_l2(void) { int i = 0; - u32 cluster; + u32 cluster, svr = get_svr(); ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); struct ccsr_cluster_l2 __iomem *l2cache; + /* only the L2 of first cluster should be enabled as expected on T4080, + * but there is no EOC in the first cluster as HW sake, so return here + * to skip enabling L2 cache of the 2nd cluster. + */ + if (SVR_SOC_VER(svr) == SVR_T4080) + return 0; + cluster = in_be32(&gur->tp_cluster[i].lower); if (cluster & TP_CLUSTER_EOC) return 0; @@ -888,6 +896,7 @@ skip_l2: } #endif + init_used_tlb_cams(); return 0; } diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init_early.c b/arch/powerpc/cpu/mpc85xx/cpu_init_early.c index 998781b706..47b712d56b 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init_early.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init_early.c @@ -102,11 +102,13 @@ void cpu_init_early_f(void *fdt) for (i = 0; i < sizeof(gd_t); i++) ((char *)gd)[i] = 0; +#ifdef CONFIG_QEMU_E500 /* * CONFIG_SYS_CCSRBAR_PHYS below may use gd->fdt_blob on ePAPR systems, * so we need to populate it before it accesses it. */ gd->fdt_blob = fdt; +#endif mas0 = MAS0_TLBSEL(1) | MAS0_ESEL(13); mas1 = MAS1_VALID | MAS1_TID(0) | MAS1_TS | MAS1_TSIZE(BOOKE_PAGESZ_1M); diff --git a/arch/powerpc/cpu/mpc85xx/speed.c b/arch/powerpc/cpu/mpc85xx/speed.c index d516d4e4a6..3236f6a5da 100644 --- a/arch/powerpc/cpu/mpc85xx/speed.c +++ b/arch/powerpc/cpu/mpc85xx/speed.c @@ -123,7 +123,8 @@ void get_sys_info(sys_info_t *sys_info) * T4240/T4160 Rev1.0. eg. It's 12 in Rev1.0, however, for Rev2.0 * it uses 6. */ -#if defined(CONFIG_PPC_T4240) || defined(CONFIG_PPC_T4160) +#if defined(CONFIG_PPC_T4240) || defined(CONFIG_PPC_T4160) || \ + defined(CONFIG_PPC_T4080) if (SVR_MAJ(get_svr()) >= 2) mem_pll_rat *= 2; #endif diff --git a/arch/powerpc/cpu/mpc85xx/spl_minimal.c b/arch/powerpc/cpu/mpc85xx/spl_minimal.c index 9e4c6c9078..cc45f715e8 100644 --- a/arch/powerpc/cpu/mpc85xx/spl_minimal.c +++ b/arch/powerpc/cpu/mpc85xx/spl_minimal.c @@ -12,7 +12,7 @@ DECLARE_GLOBAL_DATA_PTR; -void cpu_init_f(void) +ulong cpu_init_f(void) { #ifdef CONFIG_SYS_INIT_L2_ADDR ccsr_l2cache_t *l2cache = (void *)CONFIG_SYS_MPC85xx_L2_ADDR; @@ -27,6 +27,8 @@ void cpu_init_f(void) out_be32(&l2cache->l2ctl, (MPC85xx_L2CTL_L2E | MPC85xx_L2CTL_L2SRAM_ENTIRE)); #endif + + return 0; } #ifndef CONFIG_SYS_FSL_TBCLK_DIV diff --git a/arch/powerpc/cpu/mpc85xx/start.S b/arch/powerpc/cpu/mpc85xx/start.S index 0e3c86a0f8..d8c9fb6b28 100644 --- a/arch/powerpc/cpu/mpc85xx/start.S +++ b/arch/powerpc/cpu/mpc85xx/start.S @@ -314,7 +314,7 @@ l2_disabled: #endif mtspr HID0,r0 -#ifndef CONFIG_E500MC +#if !defined(CONFIG_E500MC) && !defined(CONFIG_QEMU_E500) li r0,(HID1_ASTME|HID1_ABE)@l /* Addr streaming & broadcast */ mfspr r3,PVR andi. r3,r3, 0xff @@ -1158,7 +1158,7 @@ _start_cont: mtmsr r3 isync - bl cpu_init_f + bl cpu_init_f /* return boot_flag for calling board_init_f */ bl board_init_f isync diff --git a/arch/powerpc/cpu/mpc85xx/t4240_ids.c b/arch/powerpc/cpu/mpc85xx/t4240_ids.c index f181315134..1a3cb33987 100644 --- a/arch/powerpc/cpu/mpc85xx/t4240_ids.c +++ b/arch/powerpc/cpu/mpc85xx/t4240_ids.c @@ -64,11 +64,13 @@ struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = { }; #endif +#ifdef CONFIG_SYS_SRIO struct srio_liodn_id_table srio_liodn_tbl[] = { SET_SRIO_LIODN_BASE(1, 307), SET_SRIO_LIODN_BASE(2, 387), }; int srio_liodn_tbl_sz = ARRAY_SIZE(srio_liodn_tbl); +#endif struct liodn_id_table liodn_tbl[] = { #ifdef CONFIG_SYS_DPAA_QBMAN diff --git a/arch/powerpc/cpu/mpc85xx/t4240_serdes.c b/arch/powerpc/cpu/mpc85xx/t4240_serdes.c index ff55e3c357..1f99a0a897 100644 --- a/arch/powerpc/cpu/mpc85xx/t4240_serdes.c +++ b/arch/powerpc/cpu/mpc85xx/t4240_serdes.c @@ -172,7 +172,7 @@ static const struct serdes_config serdes4_cfg_tbl[] = { {18, {PCIE3, PCIE3, PCIE3, PCIE3, AURORA, AURORA, AURORA, AURORA}}, {} }; -#elif defined(CONFIG_PPC_T4160) +#elif defined(CONFIG_PPC_T4160) || defined(CONFIG_PPC_T4080) static const struct serdes_config serdes1_cfg_tbl[] = { /* SerDes 1 */ {1, {XAUI_FM1_MAC9, XAUI_FM1_MAC9, diff --git a/arch/powerpc/cpu/mpc86xx/start.S b/arch/powerpc/cpu/mpc86xx/start.S index e33672a3a0..ec5f4a756a 100644 --- a/arch/powerpc/cpu/mpc86xx/start.S +++ b/arch/powerpc/cpu/mpc86xx/start.S @@ -273,6 +273,7 @@ diag_done: /* bl l2cache_enable */ /* run 1st part of board init code (from Flash) */ + li r3, 0 /* clear boot_flag for calling board_init_f */ bl board_init_f sync diff --git a/arch/powerpc/cpu/mpc8xxx/cpu.c b/arch/powerpc/cpu/mpc8xxx/cpu.c index 35795c4fbe..15561a1533 100644 --- a/arch/powerpc/cpu/mpc8xxx/cpu.c +++ b/arch/powerpc/cpu/mpc8xxx/cpu.c @@ -62,10 +62,12 @@ static struct cpu_type cpu_type_list[] = { CPU_TYPE_ENTRY(T4240, T4240, 0), CPU_TYPE_ENTRY(T4120, T4120, 0), CPU_TYPE_ENTRY(T4160, T4160, 0), + CPU_TYPE_ENTRY(T4080, T4080, 4), CPU_TYPE_ENTRY(B4860, B4860, 0), CPU_TYPE_ENTRY(G4860, G4860, 0), CPU_TYPE_ENTRY(G4060, G4060, 0), CPU_TYPE_ENTRY(B4440, B4440, 0), + CPU_TYPE_ENTRY(B4460, B4460, 0), CPU_TYPE_ENTRY(G4440, G4440, 0), CPU_TYPE_ENTRY(B4420, B4420, 0), CPU_TYPE_ENTRY(B4220, B4220, 0), @@ -176,7 +178,7 @@ struct cpu_type *identify_cpu(u32 ver) /* * Return a 32-bit mask indicating which cores are present on this SOC. */ -u32 cpu_mask(void) +__weak u32 cpu_mask(void) { ccsr_pic_t __iomem *pic = (void *)CONFIG_SYS_MPC8xxx_PIC_ADDR; struct cpu_type *cpu = gd->arch.cpu; @@ -195,7 +197,7 @@ u32 cpu_mask(void) /* * Return the number of cores on this SOC. */ -int cpu_numcores(void) +__weak int cpu_numcores(void) { struct cpu_type *cpu = gd->arch.cpu; diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h index 864e74c0c7..34fc8fb534 100644 --- a/arch/powerpc/include/asm/config_mpc85xx.h +++ b/arch/powerpc/include/asm/config_mpc85xx.h @@ -247,7 +247,9 @@ #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_A005125 +#ifndef CONFIG_USB_MAX_CONTROLLER_COUNT #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 +#endif #elif defined(CONFIG_P1021) #define CONFIG_MAX_CPUS 2 @@ -591,11 +593,13 @@ #define CONFIG_SYS_FSL_ESDHC_P1010_BROKEN_SDCLK #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" #define CONFIG_SYS_FSL_ERRATUM_A005125 +#define CONFIG_SYS_FSL_ERRATUM_A005434 #define CONFIG_SYS_FSL_ERRATUM_I2C_A004447 #define CONFIG_SYS_FSL_A004447_SVR_REV 0x11 #define CONFIG_ESDHC_HC_BLK_ADDR -#elif defined(CONFIG_PPC_T4240) || defined(CONFIG_PPC_T4160) +#elif defined(CONFIG_PPC_T4240) || defined(CONFIG_PPC_T4160) || \ + defined(CONFIG_PPC_T4080) #define CONFIG_E6500 #define CONFIG_SYS_PPC64 /* 64-bit core */ #define CONFIG_FSL_CORENET /* Freescale CoreNet platform */ @@ -611,13 +615,18 @@ #define CONFIG_SYS_NUM_FM2_10GEC 2 #define CONFIG_NUM_DDR_CONTROLLERS 3 #else -#define CONFIG_MAX_CPUS 8 -#define CONFIG_SYS_FSL_CLUSTER_CLOCKS { 1, 1 } -#define CONFIG_SYS_NUM_FM1_DTSEC 7 +#define CONFIG_SYS_NUM_FM1_DTSEC 6 #define CONFIG_SYS_NUM_FM1_10GEC 1 -#define CONFIG_SYS_NUM_FM2_DTSEC 7 +#define CONFIG_SYS_NUM_FM2_DTSEC 8 #define CONFIG_SYS_NUM_FM2_10GEC 1 #define CONFIG_NUM_DDR_CONTROLLERS 2 +#if defined(CONFIG_PPC_T4160) +#define CONFIG_MAX_CPUS 8 +#define CONFIG_SYS_FSL_CLUSTER_CLOCKS { 1, 1 } +#elif defined(CONFIG_PPC_T4080) +#define CONFIG_MAX_CPUS 4 +#define CONFIG_SYS_FSL_CLUSTER_CLOCKS { 1 } +#endif #endif #define CONFIG_SYS_FSL_NUM_CC_PLLS 5 #define CONFIG_SYS_FSL_NUM_LAWS 32 @@ -798,6 +807,9 @@ defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1022) #define CONFIG_SYS_FSL_SFP_VER_3_0 #define CONFIG_SYS_FSL_ISBC_VER 2 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 +#define CONFIG_SYS_FSL_ERRATUM_A006261 +#define CONFIG_SYS_FSL_ERRATUM_A006593 +#define CONFIG_SYS_FSL_ERRATUM_A006379 #define ESDHCI_QUIRK_BROKEN_TIMEOUT_VALUE diff --git a/arch/powerpc/include/asm/fsl_errata.h b/arch/powerpc/include/asm/fsl_errata.h index 4eba85cc34..64da4bb3ba 100644 --- a/arch/powerpc/include/asm/fsl_errata.h +++ b/arch/powerpc/include/asm/fsl_errata.h @@ -16,6 +16,7 @@ static inline bool has_erratum_a006379(void) u32 svr = get_svr(); if (((SVR_SOC_VER(svr) == SVR_T4240) && SVR_MAJ(svr) <= 1) || ((SVR_SOC_VER(svr) == SVR_T4160) && SVR_MAJ(svr) <= 1) || + ((SVR_SOC_VER(svr) == SVR_T4080) && SVR_MAJ(svr) <= 1) || ((SVR_SOC_VER(svr) == SVR_B4860) && SVR_MAJ(svr) <= 2) || ((SVR_SOC_VER(svr) == SVR_B4420) && SVR_MAJ(svr) <= 2) || ((SVR_SOC_VER(svr) == SVR_T2080) && SVR_MAJ(svr) <= 1) || @@ -49,9 +50,13 @@ static inline bool has_erratum_a006261(void) return IS_SVR_REV(svr, 1, 0) || IS_SVR_REV(svr, 2, 0); case SVR_T4240: case SVR_T4160: + case SVR_T4080: return IS_SVR_REV(svr, 1, 0) || IS_SVR_REV(svr, 2, 0); case SVR_T1040: return IS_SVR_REV(svr, 1, 0); + case SVR_T2080: + case SVR_T2081: + return IS_SVR_REV(svr, 1, 0); case SVR_P5040: return IS_SVR_REV(svr, 1, 0); } diff --git a/arch/powerpc/include/asm/fsl_secure_boot.h b/arch/powerpc/include/asm/fsl_secure_boot.h index 29bef910ed..74c5d8f2d9 100644 --- a/arch/powerpc/include/asm/fsl_secure_boot.h +++ b/arch/powerpc/include/asm/fsl_secure_boot.h @@ -20,8 +20,9 @@ #if defined(CONFIG_B4860QDS) || \ defined(CONFIG_T4240QDS) || \ defined(CONFIG_T2080QDS) || \ + defined(CONFIG_T2080RDB) || \ defined(CONFIG_T1040QDS) || \ - defined(CONFIG_T1040RDB) + defined(CONFIG_T104xRDB) #define CONFIG_SYS_CPC_REINIT_F #undef CONFIG_SYS_INIT_L3_ADDR #define CONFIG_SYS_INIT_L3_ADDR 0xbff00000 diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index 741b8618d1..eff573b5ad 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -1748,7 +1748,8 @@ typedef struct ccsr_gur { /* use reserved bits 18~23 as scratch space to host DDR PLL ratio */ #define FSL_CORENET_RCWSR0_MEM_PLL_RAT_RESV_SHIFT 8 #define FSL_CORENET_RCWSR0_MEM_PLL_RAT_MASK 0x3f -#if defined(CONFIG_PPC_T4240) || defined(CONFIG_PPC_T4160) +#if defined(CONFIG_PPC_T4240) || defined(CONFIG_PPC_T4160) || \ + defined(CONFIG_PPC_T4080) #define FSL_CORENET2_RCWSR4_SRDS1_PRTCL 0xfc000000 #define FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT 26 #define FSL_CORENET2_RCWSR4_SRDS2_PRTCL 0x00fe0000 @@ -1848,7 +1849,8 @@ defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1022) #define FSL_CORENET_RCWSR11_EC2_FM2_DTSEC5_MII 0x00100000 #define FSL_CORENET_RCWSR11_EC2_FM2_DTSEC5_NONE 0x00180000 #endif -#if defined(CONFIG_PPC_T4240) || defined(CONFIG_PPC_T4160) +#if defined(CONFIG_PPC_T4240) || defined(CONFIG_PPC_T4160) || \ + defined(CONFIG_PPC_T4080) #define FSL_CORENET_RCWSR13_EC1 0x60000000 /* bits 417..418 */ #define FSL_CORENET_RCWSR13_EC1_FM2_DTSEC5_RGMII 0x00000000 #define FSL_CORENET_RCWSR13_EC1_FM2_GPIO 0x40000000 diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h index 72f30feee6..edd7375c18 100644 --- a/arch/powerpc/include/asm/processor.h +++ b/arch/powerpc/include/asm/processor.h @@ -1111,11 +1111,13 @@ #define SVR_T4240 0x824000 #define SVR_T4120 0x824001 #define SVR_T4160 0x824100 +#define SVR_T4080 0x824102 #define SVR_C291 0x850000 #define SVR_C292 0x850020 #define SVR_C293 0x850030 #define SVR_B4860 0X868000 #define SVR_G4860 0x868001 +#define SVR_B4460 0x868003 #define SVR_G4060 0x868003 #define SVR_B4440 0x868100 #define SVR_G4440 0x868101 diff --git a/arch/sandbox/lib/Makefile b/arch/sandbox/lib/Makefile index 6480ebfca6..4c1a38d6bc 100644 --- a/arch/sandbox/lib/Makefile +++ b/arch/sandbox/lib/Makefile @@ -8,4 +8,4 @@ # -obj-y += interrupts.o sandbox.o +obj-y += interrupts.o diff --git a/board/BuR/common/common.c b/board/BuR/common/common.c index 4c926ce700..25cbe62b1f 100644 --- a/board/BuR/common/common.c +++ b/board/BuR/common/common.c @@ -19,6 +19,7 @@ #include <asm/arch/clock.h> #include <asm/arch/gpio.h> #include <asm/arch/sys_proto.h> +#include <asm/arch/mmc_host_def.h> #include <asm/io.h> #include <asm/gpio.h> #include <i2c.h> @@ -214,3 +215,9 @@ int board_eth_init(bd_t *bis) return rv; } #endif /* CONFIG_DRIVER_TI_CPSW */ +#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD) +int board_mmc_init(bd_t *bis) +{ + return omap_mmc_init(1, 0, 0, -1, -1); +} +#endif diff --git a/board/boundary/nitrogen6x/nitrogen6x.c b/board/boundary/nitrogen6x/nitrogen6x.c index d9c05b07bf..84294db859 100644 --- a/board/boundary/nitrogen6x/nitrogen6x.c +++ b/board/boundary/nitrogen6x/nitrogen6x.c @@ -19,13 +19,12 @@ #include <asm/imx-common/mxc_i2c.h> #include <asm/imx-common/sata.h> #include <asm/imx-common/boot_mode.h> +#include <asm/imx-common/video.h> #include <mmc.h> #include <fsl_esdhc.h> #include <micrel.h> #include <miiphy.h> #include <netdev.h> -#include <linux/fb.h> -#include <ipu_pixfmt.h> #include <asm/arch/crm_regs.h> #include <asm/arch/mxc_hdmi.h> #include <i2c.h> @@ -331,7 +330,7 @@ int board_mmc_init(bd_t *bis) #ifdef CONFIG_MXC_SPI iomux_v3_cfg_t const ecspi1_pads[] = { /* SS1 */ - MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL), MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), @@ -446,22 +445,6 @@ static iomux_v3_cfg_t const rgb_pads[] = { MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23, }; -struct display_info_t { - int bus; - int addr; - int pixfmt; - int (*detect)(struct display_info_t const *dev); - void (*enable)(struct display_info_t const *dev); - struct fb_videomode mode; -}; - - -static int detect_hdmi(struct display_info_t const *dev) -{ - struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; - return readb(&hdmi->phy_stat0) & HDMI_DVI_STAT; -} - static void do_enable_hdmi(struct display_info_t const *dev) { imx_enable_hdmi_phy(); @@ -492,7 +475,7 @@ static void enable_rgb(struct display_info_t const *dev) gpio_direction_output(RGB_BACKLIGHT_GP, 1); } -static struct display_info_t const displays[] = {{ +struct display_info_t const displays[] = {{ .bus = -1, .addr = 0, .pixfmt = IPU_PIX_FMT_RGB24, @@ -573,51 +556,7 @@ static struct display_info_t const displays[] = {{ .sync = 0, .vmode = FB_VMODE_NONINTERLACED } } }; - -int board_video_skip(void) -{ - int i; - int ret; - char const *panel = getenv("panel"); - if (!panel) { - for (i = 0; i < ARRAY_SIZE(displays); i++) { - struct display_info_t const *dev = displays+i; - if (dev->detect(dev)) { - panel = dev->mode.name; - printf("auto-detected panel %s\n", panel); - break; - } - } - if (!panel) { - panel = displays[0].mode.name; - printf("No panel detected: default to %s\n", panel); - i = 0; - } - } else { - for (i = 0; i < ARRAY_SIZE(displays); i++) { - if (!strcmp(panel, displays[i].mode.name)) - break; - } - } - if (i < ARRAY_SIZE(displays)) { - ret = ipuv3_fb_init(&displays[i].mode, 0, - displays[i].pixfmt); - if (!ret) { - displays[i].enable(displays+i); - printf("Display: %s (%ux%u)\n", - displays[i].mode.name, - displays[i].mode.xres, - displays[i].mode.yres); - } else { - printf("LCD %s cannot be configured: %d\n", - displays[i].mode.name, ret); - } - } else { - printf("unsupported panel %s\n", panel); - ret = -EINVAL; - } - return (0 != ret); -} +size_t display_count = ARRAY_SIZE(displays); static void setup_display(void) { diff --git a/board/compulab/cm_t335/u-boot.lds b/board/compulab/cm_t335/u-boot.lds index 0984dfe6ea..c8ab716cea 100644 --- a/board/compulab/cm_t335/u-boot.lds +++ b/board/compulab/cm_t335/u-boot.lds @@ -18,6 +18,7 @@ SECTIONS .text : { *(.__image_copy_start) + *(.vectors) CPUDIR/start.o (.text*) board/compulab/cm_t335/built-in.o (.text*) *(.text*) diff --git a/board/embest/mx6boards/Makefile b/board/embest/mx6boards/Makefile new file mode 100644 index 0000000000..467fb50003 --- /dev/null +++ b/board/embest/mx6boards/Makefile @@ -0,0 +1,9 @@ +# +# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de> +# +# (C) Copyright 2011 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := mx6boards.o diff --git a/board/embest/mx6boards/mx6boards.c b/board/embest/mx6boards/mx6boards.c new file mode 100644 index 0000000000..d06b57d1e3 --- /dev/null +++ b/board/embest/mx6boards/mx6boards.c @@ -0,0 +1,601 @@ +/* + * Copyright (C) 2014 Eukréa Electromatique + * Author: Eric Bénard <eric@eukrea.com> + * Fabio Estevam <fabio.estevam@freescale.com> + * Jon Nettleton <jon.nettleton@gmail.com> + * + * based on sabresd.c which is : + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * and on hummingboard.c which is : + * Copyright (C) 2013 SolidRun ltd. + * Copyright (C) 2013 Jon Nettleton <jon.nettleton@gmail.com>. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <asm/arch/clock.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/iomux.h> +#include <asm/arch/mx6-pins.h> +#include <asm/errno.h> +#include <asm/gpio.h> +#include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/boot_mode.h> +#include <asm/imx-common/mxc_i2c.h> +#include <asm/imx-common/video.h> +#include <i2c.h> +#include <mmc.h> +#include <fsl_esdhc.h> +#include <miiphy.h> +#include <netdev.h> +#include <asm/arch/mxc_hdmi.h> +#include <asm/arch/crm_regs.h> +#include <linux/fb.h> +#include <ipu_pixfmt.h> +#include <asm/io.h> +#include <asm/arch/sys_proto.h> +DECLARE_GLOBAL_DATA_PTR; + +#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ + PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ + PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ + PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CLK_CTRL (PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | \ + PAD_CTL_HYS) + +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) + +#define ENET_PAD_CTRL_PD (PAD_CTL_PUS_100K_DOWN | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) + +#define ENET_PAD_CTRL_CLK ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) + +#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE | PAD_CTL_SRE_FAST) + +#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) + +static int board_type = -1; +#define BOARD_IS_MARSBOARD 0 +#define BOARD_IS_RIOTBOARD 1 + +int dram_init(void) +{ + gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); + + return 0; +} + +static iomux_v3_cfg_t const uart2_pads[] = { + MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static void setup_iomux_uart(void) +{ + imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads)); +} + +iomux_v3_cfg_t const enet_pads[] = { + MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), + /* GPIO16 -> AR8035 25MHz */ + MX6_PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), + /* AR8035 CLK_25M --> ENET_REF_CLK (V22) */ + MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK), + MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD), + MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD), + MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL_PD), + /* AR8035 PHY Reset */ + MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD), + /* AR8035 PHY Interrupt */ + MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(ENET_PAD_CTRL), +}; + +static void setup_iomux_enet(void) +{ + imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads)); + + /* Reset AR8035 PHY */ + gpio_direction_output(IMX_GPIO_NR(3, 31) , 0); + mdelay(2); + gpio_set_value(IMX_GPIO_NR(3, 31), 1); +} + +int mx6_rgmii_rework(struct phy_device *phydev) +{ + /* from linux/arch/arm/mach-imx/mach-imx6q.c : + * Ar803x phy SmartEEE feature cause link status generates glitch, + * which cause ethernet link down/up issue, so disable SmartEEE + */ + phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7); + phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x805d); + phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4003); + + return 0; +} + +int board_phy_config(struct phy_device *phydev) +{ + mx6_rgmii_rework(phydev); + + if (phydev->drv->config) + phydev->drv->config(phydev); + + return 0; +} + +iomux_v3_cfg_t const usdhc2_pads[] = { + MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CLK_CTRL), + MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL), /* WP */ + MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ +}; + +iomux_v3_cfg_t const usdhc3_pads[] = { + MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CLK_CTRL), + MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), +}; + +iomux_v3_cfg_t const riotboard_usdhc3_pads[] = { + MX6_PAD_SD3_DAT4__GPIO7_IO01 | MUX_PAD_CTRL(NO_PAD_CTRL), /* WP */ + MX6_PAD_SD3_DAT5__GPIO7_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ +}; + +iomux_v3_cfg_t const usdhc4_pads[] = { + MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CLK_CTRL), + MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + /* eMMC RST */ + MX6_PAD_NANDF_ALE__GPIO6_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +#ifdef CONFIG_FSL_ESDHC +struct fsl_esdhc_cfg usdhc_cfg[3] = { + {USDHC2_BASE_ADDR}, + {USDHC3_BASE_ADDR}, + {USDHC4_BASE_ADDR}, +}; + +#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4) +#define USDHC3_CD_GPIO IMX_GPIO_NR(7, 0) + +int board_mmc_getcd(struct mmc *mmc) +{ + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; + int ret = 0; + + switch (cfg->esdhc_base) { + case USDHC2_BASE_ADDR: + ret = !gpio_get_value(USDHC2_CD_GPIO); + break; + case USDHC3_BASE_ADDR: + if (board_type == BOARD_IS_RIOTBOARD) + ret = !gpio_get_value(USDHC3_CD_GPIO); + else if (board_type == BOARD_IS_MARSBOARD) + ret = 1; /* eMMC/uSDHC3 is always present */ + break; + case USDHC4_BASE_ADDR: + ret = 1; /* eMMC/uSDHC4 is always present */ + break; + } + + return ret; +} + +int board_mmc_init(bd_t *bis) +{ + s32 status = 0; + int i; + + /* + * According to the board_mmc_init() the following map is done: + * (U-boot device node) (Physical Port) + * ** RiOTboard : + * mmc0 SDCard slot (bottom) + * mmc1 uSDCard slot (top) + * mmc2 eMMC + * ** MarSBoard : + * mmc0 uSDCard slot (bottom) + * mmc1 eMMC + */ + for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { + switch (i) { + case 0: + imx_iomux_v3_setup_multiple_pads( + usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); + gpio_direction_input(USDHC2_CD_GPIO); + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); + usdhc_cfg[0].max_bus_width = 4; + break; + case 1: + imx_iomux_v3_setup_multiple_pads( + usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); + if (board_type == BOARD_IS_RIOTBOARD) { + imx_iomux_v3_setup_multiple_pads( + riotboard_usdhc3_pads, + ARRAY_SIZE(riotboard_usdhc3_pads)); + gpio_direction_input(USDHC3_CD_GPIO); + gpio_direction_output(IMX_GPIO_NR(7, 8) , 0); + udelay(250); + gpio_set_value(IMX_GPIO_NR(7, 8), 1); + } + usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); + usdhc_cfg[1].max_bus_width = 4; + break; + case 2: + imx_iomux_v3_setup_multiple_pads( + usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); + usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); + usdhc_cfg[2].max_bus_width = 4; + gpio_direction_output(IMX_GPIO_NR(6, 8) , 0); + udelay(250); + gpio_set_value(IMX_GPIO_NR(6, 8), 1); + break; + default: + printf("Warning: you configured more USDHC controllers" + "(%d) then supported by the board (%d)\n", + i + 1, CONFIG_SYS_FSL_USDHC_NUM); + return status; + } + + status |= fsl_esdhc_initialize(bis, &usdhc_cfg[i]); + } + + return status; +} +#endif + +#ifdef CONFIG_MXC_SPI +iomux_v3_cfg_t const ecspi1_pads[] = { + MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static void setup_spi(void) +{ + imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); +} +#endif + +struct i2c_pads_info i2c_pad_info1 = { + .scl = { + .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gp = IMX_GPIO_NR(5, 27) + }, + .sda = { + .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gp = IMX_GPIO_NR(5, 26) + } +}; + +struct i2c_pads_info i2c_pad_info2 = { + .scl = { + .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gp = IMX_GPIO_NR(4, 12) + }, + .sda = { + .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gp = IMX_GPIO_NR(4, 13) + } +}; + +struct i2c_pads_info i2c_pad_info3 = { + .scl = { + .i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gp = IMX_GPIO_NR(1, 5) + }, + .sda = { + .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gp = IMX_GPIO_NR(1, 6) + } +}; + +iomux_v3_cfg_t const tft_pads_riot[] = { + /* LCD_PWR_EN */ + MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* TOUCH_INT */ + MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* LED_PWR_EN */ + MX6_PAD_NANDF_CS2__GPIO6_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* BL LEVEL */ + MX6_PAD_SD1_CMD__GPIO1_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +iomux_v3_cfg_t const tft_pads_mars[] = { + /* LCD_PWR_EN */ + MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* TOUCH_INT */ + MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* LED_PWR_EN */ + MX6_PAD_NANDF_CS2__GPIO6_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* BL LEVEL (PWM4) */ + MX6_PAD_SD4_DAT2__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +#if defined(CONFIG_VIDEO_IPUV3) + +static void enable_lvds(struct display_info_t const *dev) +{ + struct iomuxc *iomux = (struct iomuxc *) + IOMUXC_BASE_ADDR; + setbits_le32(&iomux->gpr[2], + IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT); + /* set backlight level to ON */ + if (board_type == BOARD_IS_RIOTBOARD) + gpio_direction_output(IMX_GPIO_NR(1, 18) , 1); + else if (board_type == BOARD_IS_MARSBOARD) + gpio_direction_output(IMX_GPIO_NR(2, 10) , 1); +} + +static void disable_lvds(struct display_info_t const *dev) +{ + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; + + /* set backlight level to OFF */ + if (board_type == BOARD_IS_RIOTBOARD) + gpio_direction_output(IMX_GPIO_NR(1, 18) , 0); + else if (board_type == BOARD_IS_MARSBOARD) + gpio_direction_output(IMX_GPIO_NR(2, 10) , 0); + + clrbits_le32(&iomux->gpr[2], + IOMUXC_GPR2_LVDS_CH0_MODE_MASK); +} + +static void do_enable_hdmi(struct display_info_t const *dev) +{ + disable_lvds(dev); + imx_enable_hdmi_phy(); +} + +static int detect_i2c(struct display_info_t const *dev) +{ + return (0 == i2c_set_bus_num(dev->bus)) && + (0 == i2c_probe(dev->addr)); +} + +struct display_info_t const displays[] = {{ + .bus = -1, + .addr = 0, + .pixfmt = IPU_PIX_FMT_RGB24, + .detect = detect_hdmi, + .enable = do_enable_hdmi, + .mode = { + .name = "HDMI", + .refresh = 60, + .xres = 1024, + .yres = 768, + .pixclock = 15385, + .left_margin = 220, + .right_margin = 40, + .upper_margin = 21, + .lower_margin = 7, + .hsync_len = 60, + .vsync_len = 10, + .sync = FB_SYNC_EXT, + .vmode = FB_VMODE_NONINTERLACED +} }, { + .bus = 2, + .addr = 0x1, + .pixfmt = IPU_PIX_FMT_LVDS666, + .detect = detect_i2c, + .enable = enable_lvds, + .mode = { + .name = "LCD8000-97C", + .refresh = 60, + .xres = 1024, + .yres = 768, + .pixclock = 15385, + .left_margin = 100, + .right_margin = 200, + .upper_margin = 10, + .lower_margin = 20, + .hsync_len = 20, + .vsync_len = 8, + .sync = FB_SYNC_EXT, + .vmode = FB_VMODE_NONINTERLACED +} } }; +size_t display_count = ARRAY_SIZE(displays); + +static void setup_display(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; + int reg; + + enable_ipu_clock(); + imx_setup_hdmi(); + + /* Turn on LDB0, IPU,IPU DI0 clocks */ + setbits_le32(&mxc_ccm->CCGR3, + MXC_CCM_CCGR3_LDB_DI0_MASK); + + /* set LDB0 clk select to 011/011 */ + clrsetbits_le32(&mxc_ccm->cs2cdr, + MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK, + (3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)); + + setbits_le32(&mxc_ccm->cscmr2, + MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV); + + setbits_le32(&mxc_ccm->chsccdr, + (CHSCCDR_CLK_SEL_LDB_DI0 + << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)); + + reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES + | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW + | IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG + | IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT + | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG + | IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT + | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED + | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0; + writel(reg, &iomux->gpr[2]); + + clrsetbits_le32(&iomux->gpr[3], + IOMUXC_GPR3_LVDS0_MUX_CTL_MASK | + IOMUXC_GPR3_HDMI_MUX_CTL_MASK, + IOMUXC_GPR3_MUX_SRC_IPU1_DI0 + << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET); +} +#endif /* CONFIG_VIDEO_IPUV3 */ + +/* + * Do not overwrite the console + * Use always serial for U-Boot console + */ +int overwrite_console(void) +{ + return 1; +} + +int board_eth_init(bd_t *bis) +{ + setup_iomux_enet(); + + return cpu_eth_init(bis); +} + +int board_early_init_f(void) +{ + u32 cputype = cpu_type(get_cpu_rev()); + + switch (cputype) { + case MXC_CPU_MX6SOLO: + board_type = BOARD_IS_RIOTBOARD; + break; + case MXC_CPU_MX6D: + board_type = BOARD_IS_MARSBOARD; + break; + } + + setup_iomux_uart(); + + if (board_type == BOARD_IS_RIOTBOARD) + imx_iomux_v3_setup_multiple_pads( + tft_pads_riot, ARRAY_SIZE(tft_pads_riot)); + else if (board_type == BOARD_IS_MARSBOARD) + imx_iomux_v3_setup_multiple_pads( + tft_pads_mars, ARRAY_SIZE(tft_pads_mars)); +#if defined(CONFIG_VIDEO_IPUV3) + /* power ON LCD */ + gpio_direction_output(IMX_GPIO_NR(1, 29) , 1); + /* touch interrupt is an input */ + gpio_direction_input(IMX_GPIO_NR(6, 14)); + /* power ON backlight */ + gpio_direction_output(IMX_GPIO_NR(6, 15) , 1); + /* set backlight level to off */ + if (board_type == BOARD_IS_RIOTBOARD) + gpio_direction_output(IMX_GPIO_NR(1, 18) , 0); + else if (board_type == BOARD_IS_MARSBOARD) + gpio_direction_output(IMX_GPIO_NR(2, 10) , 0); + setup_display(); +#endif + + return 0; +} + +int board_init(void) +{ + /* address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + /* i2c1 : PMIC, Audio codec on RiOT, Expansion connector on MarS */ + setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); + /* i2c2 : HDMI EDID */ + setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); + /* i2c3 : LVDS, Expansion connector */ + setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3); +#ifdef CONFIG_MXC_SPI + setup_spi(); +#endif + return 0; +} + +#ifdef CONFIG_CMD_BMODE +static const struct boot_mode riotboard_boot_modes[] = { + {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)}, + {"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)}, + {"emmc", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)}, + {NULL, 0}, +}; +static const struct boot_mode marsboard_boot_modes[] = { + {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)}, + {"emmc", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)}, + {NULL, 0}, +}; +#endif + +int board_late_init(void) +{ +#ifdef CONFIG_CMD_BMODE + if (board_type == BOARD_IS_RIOTBOARD) + add_board_boot_modes(riotboard_boot_modes); + else if (board_type == BOARD_IS_RIOTBOARD) + add_board_boot_modes(marsboard_boot_modes); +#endif + + return 0; +} + +int checkboard(void) +{ + puts("Board: "); + if (board_type == BOARD_IS_MARSBOARD) + puts("MarSBoard\n"); + else if (board_type == BOARD_IS_RIOTBOARD) + puts("RIoTboard\n"); + else + printf("unknown - cputype : %02x\n", cpu_type(get_cpu_rev())); + + return 0; +} diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c index d9c88a074f..b2d5378143 100644 --- a/board/freescale/b4860qds/b4860qds.c +++ b/board/freescale/b4860qds/b4860qds.c @@ -23,6 +23,7 @@ #include "../common/qixis.h" #include "../common/vsc3316_3308.h" #include "../common/idt8t49n222a_serdes_clk.h" +#include "../common/zm7300.h" #include "b4860qds.h" #include "b4860qds_qixis.h" #include "b4860qds_crossbar_con.h" @@ -94,6 +95,238 @@ int select_i2c_ch_pca(u8 ch) return 0; } +/* + * read_voltage from sensor on I2C bus + * We use average of 4 readings, waiting for 532us befor another reading + */ +#define WAIT_FOR_ADC 532 /* wait for 532 microseconds for ADC */ +#define NUM_READINGS 4 /* prefer to be power of 2 for efficiency */ + +static inline int read_voltage(void) +{ + int i, ret, voltage_read = 0; + u16 vol_mon; + + for (i = 0; i < NUM_READINGS; i++) { + ret = i2c_read(I2C_VOL_MONITOR_ADDR, + I2C_VOL_MONITOR_BUS_V_OFFSET, 1, (void *)&vol_mon, 2); + if (ret) { + printf("VID: failed to read core voltage\n"); + return ret; + } + if (vol_mon & I2C_VOL_MONITOR_BUS_V_OVF) { + printf("VID: Core voltage sensor error\n"); + return -1; + } + debug("VID: bus voltage reads 0x%04x\n", vol_mon); + /* LSB = 4mv */ + voltage_read += (vol_mon >> I2C_VOL_MONITOR_BUS_V_SHIFT) * 4; + udelay(WAIT_FOR_ADC); + } + /* calculate the average */ + voltage_read /= NUM_READINGS; + + return voltage_read; +} + +static int adjust_vdd(ulong vdd_override) +{ + int re_enable = disable_interrupts(); + ccsr_gur_t __iomem *gur = + (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 fusesr; + u8 vid; + int vdd_target, vdd_last; + int existing_voltage, temp_voltage, voltage; /* all in 1/10 mV */ + int ret; + unsigned int orig_i2c_speed; + unsigned long vdd_string_override; + char *vdd_string; + static const uint16_t vdd[32] = { + 0, /* unused */ + 9875, /* 0.9875V */ + 9750, + 9625, + 9500, + 9375, + 9250, + 9125, + 9000, + 8875, + 8750, + 8625, + 8500, + 8375, + 8250, + 8125, + 10000, /* 1.0000V */ + 10125, + 10250, + 10375, + 10500, + 10625, + 10750, + 10875, + 11000, + 0, /* reserved */ + }; + struct vdd_drive { + u8 vid; + unsigned voltage; + }; + + ret = select_i2c_ch_pca(I2C_MUX_CH_VOL_MONITOR); + if (ret) { + printf("VID: I2c failed to switch channel\n"); + ret = -1; + goto exit; + } + + /* get the voltage ID from fuse status register */ + fusesr = in_be32(&gur->dcfg_fusesr); + vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_VID_SHIFT) & + FSL_CORENET_DCFG_FUSESR_VID_MASK; + if (vid == FSL_CORENET_DCFG_FUSESR_VID_MASK) { + vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) & + FSL_CORENET_DCFG_FUSESR_ALTVID_MASK; + } + vdd_target = vdd[vid]; + debug("VID:Reading from from fuse,vid=%x vdd is %dmV\n", + vid, vdd_target/10); + + /* check override variable for overriding VDD */ + vdd_string = getenv("b4qds_vdd_mv"); + if (vdd_override == 0 && vdd_string && + !strict_strtoul(vdd_string, 10, &vdd_string_override)) + vdd_override = vdd_string_override; + if (vdd_override >= 819 && vdd_override <= 1212) { + vdd_target = vdd_override * 10; /* convert to 1/10 mV */ + debug("VDD override is %lu\n", vdd_override); + } else if (vdd_override != 0) { + printf("Invalid value.\n"); + } + + if (vdd_target == 0) { + printf("VID: VID not used\n"); + ret = 0; + goto exit; + } + + /* + * Read voltage monitor to check real voltage. + * Voltage monitor LSB is 4mv. + */ + vdd_last = read_voltage(); + if (vdd_last < 0) { + printf("VID: abort VID adjustment\n"); + ret = -1; + goto exit; + } + + debug("VID: Core voltage is at %d mV\n", vdd_last); + ret = select_i2c_ch_pca(I2C_MUX_CH_DPM); + if (ret) { + printf("VID: I2c failed to switch channel to DPM\n"); + ret = -1; + goto exit; + } + + /* Round up to the value of step of Voltage regulator */ + voltage = roundup(vdd_target, ZM_STEP); + debug("VID: rounded up voltage = %d\n", voltage); + + /* lower the speed to 100kHz to access ZM7300 device */ + debug("VID: Setting bus speed to 100KHz if not already set\n"); + orig_i2c_speed = i2c_get_bus_speed(); + if (orig_i2c_speed != 100000) + i2c_set_bus_speed(100000); + + /* Read the existing level on board, if equal to requsted one, + no need to re-set */ + existing_voltage = zm_read_voltage(); + + /* allowing the voltage difference of one step 0.0125V acceptable */ + if ((existing_voltage >= voltage) && + (existing_voltage < (voltage + ZM_STEP))) { + debug("VID: voltage already set as requested,returning\n"); + ret = existing_voltage; + goto out; + } + debug("VID: Changing voltage for board from %dmV to %dmV\n", + existing_voltage/10, voltage/10); + + if (zm_disable_wp() < 0) { + ret = -1; + goto out; + } + /* Change Voltage: the change is done through all the steps in the + way, to avoid reset to the board due to power good signal fail + in big voltage change gap jump. + */ + if (existing_voltage > voltage) { + temp_voltage = existing_voltage - ZM_STEP; + while (temp_voltage >= voltage) { + ret = zm_write_voltage(temp_voltage); + if (ret == temp_voltage) { + temp_voltage -= ZM_STEP; + } else { + /* ZM7300 device failed to set + * the voltage */ + printf + ("VID:Stepping down vol failed:%dmV\n", + temp_voltage/10); + ret = -1; + goto out; + } + } + } else { + temp_voltage = existing_voltage + ZM_STEP; + while (temp_voltage < (voltage + ZM_STEP)) { + ret = zm_write_voltage(temp_voltage); + if (ret == temp_voltage) { + temp_voltage += ZM_STEP; + } else { + /* ZM7300 device failed to set + * the voltage */ + printf + ("VID:Stepping up vol failed:%dmV\n", + temp_voltage/10); + ret = -1; + goto out; + } + } + } + + if (zm_enable_wp() < 0) + ret = -1; + + /* restore the speed to 400kHz */ +out: debug("VID: Restore the I2C bus speed to %dKHz\n", + orig_i2c_speed/1000); + i2c_set_bus_speed(orig_i2c_speed); + if (ret < 0) + goto exit; + + ret = select_i2c_ch_pca(I2C_MUX_CH_VOL_MONITOR); + if (ret) { + printf("VID: I2c failed to switch channel\n"); + ret = -1; + goto exit; + } + vdd_last = read_voltage(); + select_i2c_ch_pca(I2C_CH_DEFAULT); + + if (vdd_last > 0) + printf("VID: Core voltage %d mV\n", vdd_last); + else + ret = -1; + +exit: + if (re_enable) + enable_interrupts(); + return ret; +} + int configure_vsc3316_3308(void) { ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); @@ -697,6 +930,13 @@ int board_early_init_r(void) #ifdef CONFIG_SYS_DPAA_QBMAN setup_portals(); #endif + /* + * Adjust core voltage according to voltage ID + * This function changes I2C mux to channel 2. + */ + if (adjust_vdd(0) < 0) + printf("Warning: Adjusting core voltage failed\n"); + /* SerDes1 refclks need to be set again, as default clks * are not suitable for CPRI and onboard SGMIIs to work * simultaneously. diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index f6a0879753..22b57ccaa8 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -48,6 +48,7 @@ obj-$(CONFIG_P5020DS) += ics307_clk.o obj-$(CONFIG_P5040DS) += ics307_clk.o obj-$(CONFIG_VSC_CROSSBAR) += vsc3316_3308.o obj-$(CONFIG_IDT8T49N222A) += idt8t49n222a_serdes_clk.o +obj-$(CONFIG_ZM7300) += zm7300.o # deal with common files for P-series corenet based devices obj-$(CONFIG_P2041RDB) += p_corenet/ diff --git a/board/freescale/common/sys_eeprom.c b/board/freescale/common/sys_eeprom.c index 9c18dd8242..6144c533ef 100644 --- a/board/freescale/common/sys_eeprom.c +++ b/board/freescale/common/sys_eeprom.c @@ -21,7 +21,7 @@ /* some boards with non-256-bytes EEPROM have special define */ /* for MAX_NUM_PORTS in board-specific file */ #ifndef MAX_NUM_PORTS -#define MAX_NUM_PORTS 23 +#define MAX_NUM_PORTS 16 #endif #define NXID_VERSION 1 #endif @@ -58,8 +58,9 @@ static struct __attribute__ ((__packed__)) eeprom { u8 res_1[21]; /* 0x2b - 0x3f Reserved */ u8 mac_count; /* 0x40 Number of MAC addresses */ u8 mac_flag; /* 0x41 MAC table flags */ - u8 mac[MAX_NUM_PORTS][6]; /* 0x42 - x MAC addresses */ - u32 crc; /* x+1 CRC32 checksum */ + u8 mac[MAX_NUM_PORTS][6]; /* 0x42 - 0xa1 MAC addresses */ + u8 res_2[90]; /* 0xa2 - 0xfb Reserved */ + u32 crc; /* 0xfc - 0xff CRC32 checksum */ #endif } e; @@ -425,13 +426,13 @@ int mac_read_from_eeprom(void) if (read_eeprom()) { printf("Read failed.\n"); - return -1; + return 0; } if (!is_valid) { printf("Invalid ID (%02x %02x %02x %02x)\n", e.id[0], e.id[1], e.id[2], e.id[3]); - return -1; + return 0; } #ifdef CONFIG_SYS_I2C_EEPROM_NXID @@ -447,7 +448,7 @@ int mac_read_from_eeprom(void) crcp = (void *)&e + crc_offset; if (crc != be32_to_cpu(*crcp)) { printf("CRC mismatch (%08x != %08x)\n", crc, be32_to_cpu(e.crc)); - return -1; + return 0; } #ifdef CONFIG_SYS_I2C_EEPROM_NXID diff --git a/board/freescale/common/zm7300.c b/board/freescale/common/zm7300.c new file mode 100644 index 0000000000..be5953ad2d --- /dev/null +++ b/board/freescale/common/zm7300.c @@ -0,0 +1,235 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* Power-One ZM7300 DPM */ +#include "zm7300.h" + +#define DPM_WP 0x96 +#define WRP_OPCODE 0x01 +#define WRM_OPCODE 0x02 +#define RRP_OPCODE 0x11 + +#define DPM_SUCCESS 0x01 +#define DPM_EXEC_FAIL 0x00 + +static const uint16_t hex_to_1_10mv[] = { + 5000, + 5125, + 5250, + 5375, + 5500, + 5625, + 5750, + 5875, + 6000, + 6125, + 6250, + 6375, + 6500, + 6625, + 6750, + 6875, + 7000, + 7125, + 7250, + 7375, + 7500, + 7625, + 7750, + 7875, + 8000, + 8125, + 8250, + 8375, + 8500, + 8625, + 8750, + 8875, + 9000, + 9125, + 9250, + 9375, + 9500, /* 0.95mV */ + 9625, + 9750, + 9875, + 10000, /* 1.0V */ + 10125, + 10250, + 10375, + 10500, + 10625, + 10750, + 10875, + 11000, + 11125, + 11250, + 11375, + 11500, + 11625, + 11750, + 11875, + 12000, + 12125, + 12250, + 12375, + 0, /* reserved */ +}; + + +/* Read Data d from Register r of POL p */ +u8 dpm_rrp(uchar r) +{ + u8 ret[5]; + + ret[0] = RRP_OPCODE; + /* POL is 0 */ + ret[1] = 0; + ret[2] = r; + i2c_read(I2C_DPM_ADDR, 0, -3, ret, 2); + if (ret[1] == DPM_SUCCESS) { /* the DPM returned success as status */ + debug("RRP_OPCODE returned success data is %x\n", ret[0]); + return ret[0]; + } else { + return -1; + } +} + +/* Write Data d into DPM register r (RAM) */ +int dpm_wrm(u8 r, u8 d) +{ + u8 ret[5]; + + ret[0] = WRM_OPCODE; + ret[1] = r; + ret[2] = d; + i2c_read(I2C_DPM_ADDR, 0, -3, ret, 1); + if (ret[0] == DPM_SUCCESS) { /* the DPM returned success as status */ + debug("WRM_OPCODE returned success data is %x\n", ret[0]); + return ret[0]; + } else { + return -1; + } +} + +/* Write Data d into Register r of POL(s) a */ +int dpm_wrp(u8 r, u8 d) +{ + u8 ret[7]; + + ret[0] = WRP_OPCODE; + /* only POL0 is present */ + ret[1] = 0x01; + ret[2] = 0x00; + ret[3] = 0x00; + ret[4] = 0x00; + ret[5] = r; + ret[6] = d; + i2c_read(I2C_DPM_ADDR, 0, -7, ret, 1); + if (ret[0] == DPM_SUCCESS) { /* the DPM returned success as status */ + debug("WRP_OPCODE returned success data is %x\n", ret[0]); + return 0; + } else { + return -1; + } +} + +/* Uses the DPM command RRP */ +u8 zm_read(uchar reg) +{ + u8 d; + d = dpm_rrp(reg); + return d; +} + +/* ZM_write -- + Steps: + a. Write data to the register + b. Read data from register and compare to written value + c. Return return_code & voltage_read +*/ +u8 zm_write(u8 reg, u8 data) +{ + u8 d; + + /* write data to register */ + dpm_wrp(reg, data); + + /* read register and compare to written value */ + d = dpm_rrp(reg); + if (d != data) { + printf("zm_write : Comparison register data failed\n"); + return -1; + } + + return d; +} + +/* zm_write_out_voltage + * voltage in 1/10 mV + */ +int zm_write_voltage(int voltage) +{ + u8 reg = 0x7, vid; + uint16_t voltage_read; + u8 ret; + + vid = (voltage - 5000) / ZM_STEP; + + ret = zm_write(reg, vid); + if (ret != -1) { + voltage_read = hex_to_1_10mv[ret]; + debug("voltage set to %dmV\n", voltage_read/10); + return voltage_read; + } + return -1; +} + +/* zm_read_out_voltage + * voltage in 1/10 mV + */ +int zm_read_voltage(void) +{ + u8 reg = 0x7; + u8 ret; + int voltage; + + ret = zm_read(reg); + if (ret != -1) { + voltage = hex_to_1_10mv[ret]; + debug("Voltage read is %dmV\n", voltage/10); + return voltage; + } else { + return -1; + } +} + +int zm_disable_wp() +{ + u8 new_wp_value; + + /* Disable using Write-Protect register 0x96 */ + new_wp_value = 0x8; + if ((dpm_wrm(DPM_WP, new_wp_value)) < 0) { + printf("Disable Write-Protect register failed\n"); + return -1; + } + return 0; +} + +int zm_enable_wp() +{ + u8 orig_wp_value; + orig_wp_value = 0x0; + + /* Enable using Write-Protect register 0x96 */ + if ((dpm_wrm(DPM_WP, orig_wp_value)) < 0) { + printf("Enable Write-Protect register failed\n"); + return -1; + } + return 0; +} + diff --git a/board/freescale/common/zm7300.h b/board/freescale/common/zm7300.h new file mode 100644 index 0000000000..6b4d035970 --- /dev/null +++ b/board/freescale/common/zm7300.h @@ -0,0 +1,22 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __ZM7300_H_ +#define __ZM7300_H 1_ + +#include <common.h> +#include <i2c.h> +#include <errno.h> +#include <asm/io.h> + +#define ZM_STEP 125 +int zm7300_set_voltage(int voltage_1_10mv); +int zm_write_voltage(int voltage); +int zm_read_voltage(void); +int zm_disable_wp(void); +int zm_enable_wp(void); + +#endif /* __ZM7300_H_ */ diff --git a/board/freescale/mx31ads/u-boot.lds b/board/freescale/mx31ads/u-boot.lds index 6da1d4b5f5..61b83bfc63 100644 --- a/board/freescale/mx31ads/u-boot.lds +++ b/board/freescale/mx31ads/u-boot.lds @@ -22,6 +22,7 @@ SECTIONS /* WARNING - the following is hand-optimized to fit within */ /* the sector layout of our flash chips! XXX FIXME XXX */ + * (.vectors) arch/arm/cpu/arm1136/start.o (.text*) board/freescale/mx31ads/built-in.o (.text*) arch/arm/lib/built-in.o (.text*) diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c index d7d932eeb8..3e314daec2 100644 --- a/board/freescale/mx6sabresd/mx6sabresd.c +++ b/board/freescale/mx6sabresd/mx6sabresd.c @@ -14,14 +14,13 @@ #include <asm/gpio.h> #include <asm/imx-common/iomux-v3.h> #include <asm/imx-common/boot_mode.h> +#include <asm/imx-common/video.h> #include <mmc.h> #include <fsl_esdhc.h> #include <miiphy.h> #include <netdev.h> #include <asm/arch/mxc_hdmi.h> #include <asm/arch/crm_regs.h> -#include <linux/fb.h> -#include <ipu_pixfmt.h> #include <asm/io.h> #include <asm/arch/sys_proto.h> DECLARE_GLOBAL_DATA_PTR; @@ -265,22 +264,6 @@ int board_phy_config(struct phy_device *phydev) } #if defined(CONFIG_VIDEO_IPUV3) -struct display_info_t { - int bus; - int addr; - int pixfmt; - int (*detect)(struct display_info_t const *dev); - void (*enable)(struct display_info_t const *dev); - struct fb_videomode mode; -}; - -static int detect_hdmi(struct display_info_t const *dev) -{ - struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; - return readb(&hdmi->phy_stat0) & HDMI_DVI_STAT; -} - - static void disable_lvds(struct display_info_t const *dev) { struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; @@ -309,7 +292,7 @@ static void enable_lvds(struct display_info_t const *dev) writel(reg, &iomux->gpr[2]); } -static struct display_info_t const displays[] = {{ +struct display_info_t const displays[] = {{ .bus = -1, .addr = 0, .pixfmt = IPU_PIX_FMT_RGB666, @@ -350,51 +333,7 @@ static struct display_info_t const displays[] = {{ .sync = FB_SYNC_EXT, .vmode = FB_VMODE_NONINTERLACED } } }; - -int board_video_skip(void) -{ - int i; - int ret; - char const *panel = getenv("panel"); - if (!panel) { - for (i = 0; i < ARRAY_SIZE(displays); i++) { - struct display_info_t const *dev = displays+i; - if (dev->detect && dev->detect(dev)) { - panel = dev->mode.name; - printf("auto-detected panel %s\n", panel); - break; - } - } - if (!panel) { - panel = displays[0].mode.name; - printf("No panel detected: default to %s\n", panel); - i = 0; - } - } else { - for (i = 0; i < ARRAY_SIZE(displays); i++) { - if (!strcmp(panel, displays[i].mode.name)) - break; - } - } - if (i < ARRAY_SIZE(displays)) { - ret = ipuv3_fb_init(&displays[i].mode, 0, - displays[i].pixfmt); - if (!ret) { - displays[i].enable(displays+i); - printf("Display: %s (%ux%u)\n", - displays[i].mode.name, - displays[i].mode.xres, - displays[i].mode.yres); - } else - printf("LCD %s cannot be configured: %d\n", - displays[i].mode.name, ret); - } else { - printf("unsupported panel %s\n", panel); - return -EINVAL; - } - - return 0; -} +size_t display_count = ARRAY_SIZE(displays); static void setup_display(void) { diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c index aadad3266f..d2b64cc357 100644 --- a/board/freescale/mx6slevk/mx6slevk.c +++ b/board/freescale/mx6slevk/mx6slevk.c @@ -34,6 +34,9 @@ DECLARE_GLOBAL_DATA_PTR; PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ PAD_CTL_DSE_40ohm | PAD_CTL_HYS) +#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) + #define ETH_PHY_RESET IMX_GPIO_NR(4, 21) int dram_init(void) @@ -71,6 +74,20 @@ static iomux_v3_cfg_t const fec_pads[] = { MX6_PAD_FEC_TX_CLK__GPIO_4_21 | MUX_PAD_CTRL(NO_PAD_CTRL), }; +#ifdef CONFIG_MXC_SPI +static iomux_v3_cfg_t ecspi1_pads[] = { + MX6_PAD_ECSPI1_MISO__ECSPI_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_ECSPI1_MOSI__ECSPI_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_ECSPI1_SCLK__ECSPI_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_ECSPI1_SS0__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static void setup_spi(void) +{ + imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); +} +#endif + static void setup_iomux_uart(void) { imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); @@ -132,6 +149,9 @@ static int setup_fec(void) int board_early_init_f(void) { setup_iomux_uart(); +#ifdef CONFIG_MXC_SPI + setup_spi(); +#endif return 0; } diff --git a/board/freescale/p1_p2_rdb/Makefile b/board/freescale/p1_p2_rdb/Makefile index f7b568a021..a97bf45f00 100644 --- a/board/freescale/p1_p2_rdb/Makefile +++ b/board/freescale/p1_p2_rdb/Makefile @@ -4,8 +4,27 @@ # SPDX-License-Identifier: GPL-2.0+ # +MINIMAL= + +ifdef CONFIG_SPL_BUILD +ifdef CONFIG_SPL_INIT_MINIMAL +MINIMAL=y +endif +endif + +ifdef MINIMAL + +obj-y += spl_minimal.o tlb.o law.o + +else +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +else obj-y += p1_p2_rdb.o +obj-$(CONFIG_PCI) += pci.o +endif obj-y += ddr.o obj-y += law.o -obj-$(CONFIG_PCI) += pci.o obj-y += tlb.o + +endif diff --git a/board/freescale/p1_p2_rdb/ddr.c b/board/freescale/p1_p2_rdb/ddr.c index 17d3beac39..98ee5f1021 100644 --- a/board/freescale/p1_p2_rdb/ddr.c +++ b/board/freescale/p1_p2_rdb/ddr.c @@ -180,27 +180,22 @@ fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = { phys_size_t fixed_sdram (void) { - char buf[32]; fsl_ddr_cfg_regs_t ddr_cfg_regs; size_t ddr_size; struct cpu_type *cpu; ulong ddr_freq, ddr_freq_mhz; cpu = gd->arch.cpu; - /* P1020 and it's derivatives support max 32bit DDR width */ - if (cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1011) { - ddr_size = (CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 / 2); - } else { - ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; - } + + ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; + #if defined(CONFIG_SYS_RAMBOOT) return ddr_size; #endif ddr_freq = get_ddr_freq(0); ddr_freq_mhz = ddr_freq / 1000000; - printf("Configuring DDR for %s MT/s data rate\n", - strmhz(buf, ddr_freq)); + printf("Configuring DDR for %ld T/s data rate\n", ddr_freq); if(ddr_freq_mhz <= 400) memcpy(&ddr_cfg_regs, &ddr_cfg_regs_400, sizeof(ddr_cfg_regs)); @@ -211,8 +206,7 @@ phys_size_t fixed_sdram (void) else if(ddr_freq_mhz <= 800) memcpy(&ddr_cfg_regs, &ddr_cfg_regs_800, sizeof(ddr_cfg_regs)); else - panic("Unsupported DDR data rate %s MT/s data rate\n", - strmhz(buf, ddr_freq)); + panic("Unsupported DDR data rate %ld T/s\n", ddr_freq); /* P1020 and it's derivatives support max 32bit DDR width */ if (cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1011) { diff --git a/board/freescale/p1_p2_rdb/spl.c b/board/freescale/p1_p2_rdb/spl.c new file mode 100644 index 0000000000..f30c5fe3e6 --- /dev/null +++ b/board/freescale/p1_p2_rdb/spl.c @@ -0,0 +1,141 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <ns16550.h> +#include <malloc.h> +#include <mmc.h> +#include <nand.h> +#include <i2c.h> +#include <fsl_esdhc.h> +#include <spi_flash.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define SYSCLK_MASK 0x00200000 +#define BOARDREV_MASK 0x10100000 + +#define SYSCLK_66 66666666 +#define SYSCLK_100 100000000 + +unsigned long get_board_sys_clk(ulong dummy) +{ + ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR); + u32 val_gpdat, sysclk_gpio; + + val_gpdat = in_be32(&pgpio->gpdat); + sysclk_gpio = val_gpdat & SYSCLK_MASK; + + if (sysclk_gpio == 0) + return SYSCLK_66; + else + return SYSCLK_100; + + return 0; +} + +phys_size_t get_effective_memsize(void) +{ + return CONFIG_SYS_L2_SIZE; +} + +void board_init_f(ulong bootflag) +{ + u32 plat_ratio, bus_clk; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + + console_init_f(); + + /* Set pmuxcr to allow both i2c1 and i2c2 */ + setbits_be32(&gur->pmuxcr, in_be32(&gur->pmuxcr) | 0x1000); + setbits_be32(&gur->pmuxcr, + in_be32(&gur->pmuxcr) | MPC85xx_PMUXCR_SD_DATA); + + /* Read back the register to synchronize the write. */ + in_be32(&gur->pmuxcr); + +#ifdef CONFIG_SPL_SPI_BOOT + clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA); +#endif + + /* initialize selected port with appropriate baud rate */ + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + plat_ratio >>= 1; + bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; + gd->bus_clk = bus_clk; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + bus_clk / 16 / CONFIG_BAUDRATE); +#ifdef CONFIG_SPL_MMC_BOOT + puts("\nSD boot...\n"); +#elif defined(CONFIG_SPL_SPI_BOOT) + puts("\nSPI Flash boot...\n"); +#endif + + /* copy code to RAM and jump to it - this should not return */ + /* NOTE - code has to be copied out of NAND buffer before + * other blocks can be read. + */ + relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + /* Pointer is writable since we allocated a register for it */ + gd = (gd_t *)CONFIG_SPL_GD_ADDR; + bd_t *bd; + + memset(gd, 0, sizeof(gd_t)); + bd = (bd_t *)(CONFIG_SPL_GD_ADDR + sizeof(gd_t)); + memset(bd, 0, sizeof(bd_t)); + gd->bd = bd; + bd->bi_memstart = CONFIG_SYS_INIT_L2_ADDR; + bd->bi_memsize = CONFIG_SYS_L2_SIZE; + + probecpu(); + get_clocks(); + mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR, + CONFIG_SPL_RELOC_MALLOC_SIZE); + +#ifdef CONFIG_SPL_MMC_BOOT + mmc_initialize(bd); +#endif + /* relocate environment function pointers etc. */ +#ifdef CONFIG_SPL_NAND_BOOT + nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif +#ifdef CONFIG_SPL_NAND_BOOT + nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif +#ifdef CONFIG_SPL_MMC_BOOT + mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif +#ifdef CONFIG_SPL_SPI_BOOT + spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif + + gd->env_addr = (ulong)(CONFIG_ENV_ADDR); + gd->env_valid = 1; + + gd->ram_size = initdram(0); +#ifdef CONFIG_SPL_NAND_BOOT + puts("Tertiary program loader running in sram..."); +#else + puts("Second program loader running in sram...\n"); +#endif + +#ifdef CONFIG_SPL_MMC_BOOT + mmc_boot(); +#elif defined(CONFIG_SPL_SPI_BOOT) + spi_boot(); +#elif defined(CONFIG_SPL_NAND_BOOT) + nand_boot(); +#endif +} diff --git a/board/freescale/p1_p2_rdb/spl_minimal.c b/board/freescale/p1_p2_rdb/spl_minimal.c new file mode 100644 index 0000000000..96a4d1cb0a --- /dev/null +++ b/board/freescale/p1_p2_rdb/spl_minimal.c @@ -0,0 +1,84 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <ns16550.h> +#include <asm/io.h> +#include <nand.h> +#include <linux/compiler.h> +#include <asm/fsl_law.h> +#include <fsl_ddr_sdram.h> +#include <asm/global_data.h> + +DECLARE_GLOBAL_DATA_PTR; +#define SYSCLK_MASK 0x00200000 +#define BOARDREV_MASK 0x10100000 + +#define SYSCLK_66 66666666 +#define SYSCLK_100 100000000 + +unsigned long get_board_sys_clk(ulong dummy) +{ + ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR); + u32 val_gpdat, sysclk_gpio; + + val_gpdat = in_be32(&pgpio->gpdat); + sysclk_gpio = val_gpdat & SYSCLK_MASK; + + if (sysclk_gpio == 0) + return SYSCLK_66; + else + return SYSCLK_100; + + return 0; +} + +void board_init_f(ulong bootflag) +{ + u32 plat_ratio; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + +#if defined(CONFIG_SYS_NAND_BR_PRELIM) && defined(CONFIG_SYS_NAND_OR_PRELIM) + set_lbc_br(0, CONFIG_SYS_NAND_BR_PRELIM); + set_lbc_or(0, CONFIG_SYS_NAND_OR_PRELIM); +#endif + + /* initialize selected port with appropriate baud rate */ + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + plat_ratio >>= 1; + gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + gd->bus_clk / 16 / CONFIG_BAUDRATE); + + puts("\nNAND boot... "); + + /* copy code to RAM and jump to it - this should not return */ + /* NOTE - code has to be copied out of NAND buffer before + * other blocks can be read. + */ + relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + puts("\nSecond program loader running in sram..."); + nand_boot(); +} + +void putc(char c) +{ + if (c == '\n') + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r'); + + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c); +} + +void puts(const char *str) +{ + while (*str) + putc(*str++); +} diff --git a/board/freescale/p1_p2_rdb/tlb.c b/board/freescale/p1_p2_rdb/tlb.c index bc98972e33..73f5729ef5 100644 --- a/board/freescale/p1_p2_rdb/tlb.c +++ b/board/freescale/p1_p2_rdb/tlb.c @@ -37,6 +37,7 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 1, BOOKE_PAGESZ_1M, 1), +#ifndef CONFIG_SPL_BUILD /* W**G* - Flash/promjet, localbus */ /* This will be changed to *I*G* after relocation to RAM. */ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, @@ -55,6 +56,7 @@ struct fsl_e_tlb_entry tlb_table[] = { 0, 4, BOOKE_PAGESZ_256K, 1), #endif /* #if defined(CONFIG_PCI) */ +#endif /* *I*G - NAND */ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, @@ -65,7 +67,21 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 6, BOOKE_PAGESZ_1M, 1), -#if defined(CONFIG_SYS_RAMBOOT) +#ifdef CONFIG_SYS_INIT_L2_ADDR + /* *I*G - L2SRAM */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, + 0, 11, BOOKE_PAGESZ_256K, 1), +#if CONFIG_SYS_L2_SIZE >= (256 << 10) + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000, + CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 12, BOOKE_PAGESZ_256K, 1), +#endif +#endif + +#if defined(CONFIG_SYS_RAMBOOT) || \ + (defined(CONFIG_SPL) && !defined(CONFIG_SPL_COMMON_INIT_DDR)) SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, 7, BOOKE_PAGESZ_1G, 1) diff --git a/board/freescale/qemu-ppce500/qemu-ppce500.c b/board/freescale/qemu-ppce500/qemu-ppce500.c index 3dbb0cf43b..230870d90e 100644 --- a/board/freescale/qemu-ppce500/qemu-ppce500.c +++ b/board/freescale/qemu-ppce500/qemu-ppce500.c @@ -346,3 +346,23 @@ ulong get_bus_freq (ulong dummy) get_sys_info(&sys_info); return sys_info.freq_systembus; } + +/* + * Return the number of cores on this SOC. + */ +int cpu_numcores(void) +{ + /* + * The QEMU u-boot target only needs to drive the first core, + * spinning and device tree nodes get driven by QEMU itself + */ + return 1; +} + +/* + * Return a 32-bit mask indicating which cores are present on this SOC. + */ +u32 cpu_mask(void) +{ + return (1 << cpu_numcores()) - 1; +} diff --git a/board/freescale/t104xrdb/t104xrdb.c b/board/freescale/t104xrdb/t104xrdb.c index fb5b84940e..a5e5fffac4 100644 --- a/board/freescale/t104xrdb/t104xrdb.c +++ b/board/freescale/t104xrdb/t104xrdb.c @@ -109,6 +109,8 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_DEEP_SLEEP void board_mem_sleep_setup(void) { + /* does not provide HW signals for power management */ + CPLD_WRITE(misc_ctl_status, (CPLD_READ(misc_ctl_status) & ~0x40)); /* Disable MCKE isolation */ gpio_set_value(2, 0); udelay(1); diff --git a/board/freescale/t4rdb/Makefile b/board/freescale/t4rdb/Makefile new file mode 100644 index 0000000000..f7f7fc0177 --- /dev/null +++ b/board/freescale/t4rdb/Makefile @@ -0,0 +1,12 @@ +# +# Copyright 2014 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-$(CONFIG_T4240RDB) += t4240rdb.o +obj-y += ddr.o +obj-y += eth.o +obj-$(CONFIG_PCI) += pci.o +obj-y += law.o +obj-y += tlb.o diff --git a/board/freescale/t4rdb/ddr.c b/board/freescale/t4rdb/ddr.c new file mode 100644 index 0000000000..5a43c1bc78 --- /dev/null +++ b/board/freescale/t4rdb/ddr.c @@ -0,0 +1,118 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <hwconfig.h> +#include <asm/mmu.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> +#include <asm/fsl_law.h> +#include "ddr.h" + +DECLARE_GLOBAL_DATA_PTR; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; + ulong ddr_freq; + + if (ctrl_num > 2) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + if (!pdimm->n_ranks) + return; + + /* + * we use identical timing for all slots. If needed, change the code + * to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num]; + */ + if (popts->registered_dimm_en) + pbsp = rdimms[0]; + else + pbsp = udimms[0]; + + + /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + while (pbsp->datarate_mhz_high) { + if (pbsp->n_ranks == pdimm->n_ranks && + (pdimm->rank_density >> 30) >= pbsp->rank_gb) { + if (ddr_freq <= pbsp->datarate_mhz_high) { + popts->clk_adjust = pbsp->clk_adjust; + popts->wrlvl_start = pbsp->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + goto found; + } + pbsp_highest = pbsp; + } + pbsp++; + } + + if (pbsp_highest) { + printf("Error: board specific timing not found for data\n" + "rate %lu MT/s\n" + "Trying to use the highest speed (%u) parameters\n", + ddr_freq, pbsp_highest->datarate_mhz_high); + popts->clk_adjust = pbsp_highest->clk_adjust; + popts->wrlvl_start = pbsp_highest->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + } else { + panic("DIMM is not supported by this board"); + } +found: + debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n" + "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x,\n" + "wrlvl_ctrl_3 0x%x\n", + pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb, + pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2, + pbsp->wrlvl_ctl_3); + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * Rtt and Rtt_WR override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size; + + puts("Initializing....using SPD\n"); + + dram_size = fsl_ddr_sdram(); + + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; + + puts(" DDR: "); + return dram_size; +} diff --git a/board/freescale/t4rdb/ddr.h b/board/freescale/t4rdb/ddr.h new file mode 100644 index 0000000000..7b854767e7 --- /dev/null +++ b/board/freescale/t4rdb/ddr.h @@ -0,0 +1,78 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __DDR_H__ +#define __DDR_H__ +struct board_specific_parameters { + u32 n_ranks; + u32 datarate_mhz_high; + u32 rank_gb; + u32 clk_adjust; + u32 wrlvl_start; + u32 wrlvl_ctl_2; + u32 wrlvl_ctl_3; +}; + +/* + * These tables contain all valid speeds we want to override with board + * specific parameters. datarate_mhz_high values need to be in ascending order + * for each n_ranks group. + */ +static const struct board_specific_parameters udimm0[] = { + /* + * memory controller 0 + * num| hi| rank| clk| wrlvl | wrlvl | wrlvl + * ranks| mhz| GB |adjst| start | ctl2 | ctl3 + */ + {2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a}, + {2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09}, + {2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b}, + {2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a}, + {2, 1900, 0, 4, 8, 0x090a0b0e, 0x0f11120c}, + {2, 2140, 0, 4, 8, 0x090a0b0e, 0x0f11120c}, + {1, 1350, 0, 5, 8, 0x0809090b, 0x0c0c0d0a}, + {1, 1700, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a}, + {1, 1900, 0, 4, 8, 0x080a0a0c, 0x0e0e0f0a}, + {1, 2140, 0, 4, 8, 0x090a0b0c, 0x0e0f100b}, + {} +}; + +static const struct board_specific_parameters rdimm0[] = { + /* + * memory controller 0 + * num| hi| rank| clk| wrlvl | wrlvl | wrlvl + * ranks| mhz| GB |adjst| start | ctl2 | ctl3 + */ + {4, 1350, 0, 5, 9, 0x08070605, 0x06070806}, + {4, 1666, 0, 5, 11, 0x0a080706, 0x07090906}, + {4, 2140, 0, 5, 12, 0x0b090807, 0x080a0b07}, + {2, 1350, 0, 5, 9, 0x08070605, 0x06070806}, + {2, 1666, 0, 5, 11, 0x0a090806, 0x08090a06}, + {2, 2140, 0, 5, 12, 0x0b090807, 0x080a0b07}, + {1, 1350, 0, 5, 9, 0x08070605, 0x06070806}, + {1, 1666, 0, 5, 11, 0x0a090806, 0x08090a06}, + {1, 2140, 0, 4, 12, 0x0b090807, 0x080a0b07}, + {} +}; + +/* + * The three slots have slightly different timing. The center values are good + * for all slots. We use identical speed tables for them. In future use, if + * DIMMs require separated tables, make more entries as needed. + */ +static const struct board_specific_parameters *udimms[] = { + udimm0, +}; + +/* + * The three slots have slightly different timing. See comments above. + */ +static const struct board_specific_parameters *rdimms[] = { + rdimm0, +}; + + +#endif diff --git a/board/freescale/t4rdb/eth.c b/board/freescale/t4rdb/eth.c new file mode 100644 index 0000000000..d220475b5a --- /dev/null +++ b/board/freescale/t4rdb/eth.c @@ -0,0 +1,146 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * Chunhe Lan <Chunhe.Lan@freescale.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <netdev.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <fsl_ddr_sdram.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <malloc.h> +#include <fm_eth.h> +#include <fsl_mdio.h> +#include <miiphy.h> +#include <phy.h> +#include <asm/fsl_dtsec.h> +#include <asm/fsl_serdes.h> +#include <hwconfig.h> + +#include "../common/fman.h" +#include "t4rdb.h" + +void fdt_fixup_board_enet(void *fdt) +{ + return; +} + +int board_eth_init(bd_t *bis) +{ +#if defined(CONFIG_FMAN_ENET) + int i, interface; + struct memac_mdio_info dtsec_mdio_info; + struct memac_mdio_info tgec_mdio_info; + struct mii_dev *dev; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 srds_prtcl_s1, srds_prtcl_s2; + + srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS1_PRTCL; + srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; + srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS2_PRTCL; + srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; + + dtsec_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM2_DTSEC_MDIO_ADDR; + + dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + /* Register the 1G MDIO bus */ + fm_memac_mdio_init(bis, &dtsec_mdio_info); + + tgec_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM2_TGEC_MDIO_ADDR; + tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME; + + /* Register the 10G MDIO bus */ + fm_memac_mdio_init(bis, &tgec_mdio_info); + + if (srds_prtcl_s1 == 28) { + /* SGMII */ + fm_info_set_phy_address(FM1_DTSEC1, SGMII_PHY_ADDR1); + fm_info_set_phy_address(FM1_DTSEC2, SGMII_PHY_ADDR2); + fm_info_set_phy_address(FM1_DTSEC3, SGMII_PHY_ADDR3); + fm_info_set_phy_address(FM1_DTSEC4, SGMII_PHY_ADDR4); + } else { + puts("Invalid SerDes1 protocol for T4240RDB\n"); + } + + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + interface = fm_info_get_enet_if(i); + switch (interface) { + case PHY_INTERFACE_MODE_SGMII: + dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME); + fm_info_set_mdio(i, dev); + break; + default: + break; + } + } + + for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) { + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_XGMII: + dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME); + fm_info_set_mdio(i, dev); + break; + default: + break; + } + } + +#if (CONFIG_SYS_NUM_FMAN == 2) + if (srds_prtcl_s2 == 56) { + /* SGMII && XFI */ + fm_info_set_phy_address(FM2_DTSEC1, SGMII_PHY_ADDR5); + fm_info_set_phy_address(FM2_DTSEC2, SGMII_PHY_ADDR6); + fm_info_set_phy_address(FM2_DTSEC3, SGMII_PHY_ADDR7); + fm_info_set_phy_address(FM2_DTSEC4, SGMII_PHY_ADDR8); + fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR); + fm_info_set_phy_address(FM1_10GEC2, FM1_10GEC2_PHY_ADDR); + fm_info_set_phy_address(FM2_10GEC1, FM2_10GEC2_PHY_ADDR); + fm_info_set_phy_address(FM2_10GEC2, FM2_10GEC1_PHY_ADDR); + } else { + puts("Invalid SerDes2 protocol for T4240RDB\n"); + } + + for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) { + interface = fm_info_get_enet_if(i); + switch (interface) { + case PHY_INTERFACE_MODE_SGMII: + dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME); + fm_info_set_mdio(i, dev); + break; + default: + break; + } + } + + for (i = FM2_10GEC1; i < FM2_10GEC1 + CONFIG_SYS_NUM_FM2_10GEC; i++) { + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_XGMII: + dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME); + fm_info_set_mdio(i, dev); + break; + default: + break; + } + } +#endif /* CONFIG_SYS_NUM_FMAN */ + + cpu_eth_init(bis); +#endif /* CONFIG_FMAN_ENET */ + + return pci_eth_init(bis); +} diff --git a/board/freescale/t4rdb/law.c b/board/freescale/t4rdb/law.c new file mode 100644 index 0000000000..1f5876885c --- /dev/null +++ b/board/freescale/t4rdb/law.c @@ -0,0 +1,28 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + /* Limit DCSR to 32M to access NPC Trace Buffer */ + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/t4rdb/pci.c b/board/freescale/t4rdb/pci.c new file mode 100644 index 0000000000..6387a20cae --- /dev/null +++ b/board/freescale/t4rdb/pci.c @@ -0,0 +1,23 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/fsl_pci.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <asm/fsl_serdes.h> + +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/freescale/t4rdb/t4240rdb.c b/board/freescale/t4rdb/t4240rdb.c new file mode 100644 index 0000000000..5448c86c48 --- /dev/null +++ b/board/freescale/t4rdb/t4240rdb.c @@ -0,0 +1,125 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <i2c.h> +#include <netdev.h> +#include <linux/compiler.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <fm_eth.h> + +#include "t4rdb.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + struct cpu_type *cpu = gd->arch.cpu; + + printf("Board: %sRDB, ", cpu->name); + + puts("SERDES Reference Clocks:\n"); + printf(" SERDES1=100MHz SERDES2=156.25MHz\n" + " SERDES3=100MHz SERDES4=100MHz\n"); + + return 0; +} + +int board_early_init_r(void) +{ + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash + PROMJET region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash + promjet */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); + + set_liodns(); +#ifdef CONFIG_SYS_DPAA_QBMAN + setup_portals(); +#endif + + return 0; +} + +int misc_init_r(void) +{ + return 0; +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); + fdt_fixup_dr_usb(blob, bd); + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); + fdt_fixup_board_enet(blob); +#endif +} + +/* + * This function is called by bdinfo to print detail board information. + * As an exmaple for future board, we organize the messages into + * several sections. If applicable, the message is in the format of + * <name> = <value> + * It should aligned with normal output of bdinfo command. + * + * Voltage: Core, DDR and another configurable voltages + * Clock : Critical clocks which are not printed already + * RCW : RCW source if not printed already + * Misc : Other important information not in above catagories + */ +void board_detail(void) +{ + int rcwsrc; + + /* RCW section SW3[4] */ + rcwsrc = 0x0; + puts("RCW source = "); + switch (rcwsrc & 0x1) { + case 0x1: + puts("SDHC/eMMC\n"); + break; + default: + puts("I2C normal addressing\n"); + break; + } +} diff --git a/board/freescale/t4rdb/t4_pbi.cfg b/board/freescale/t4rdb/t4_pbi.cfg new file mode 100644 index 0000000000..c9f8ced2a3 --- /dev/null +++ b/board/freescale/t4rdb/t4_pbi.cfg @@ -0,0 +1,31 @@ +# +# Copyright 2014 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +#PBI commands +#Initialize CPC1 +09010000 00200400 +09138000 00000000 +091380c0 00000100 +#512KB SRAM +09010100 00000000 +09010104 fff80009 +09010f00 08000000 +#enable CPC1 +09010000 80000000 +#Configure LAW for CPC1 +09000d00 00000000 +09000d04 fff80000 +09000d08 81000012 +#slow mdio clock +095fc030 00008148 +095fd030 00808148 +#Configure alternate space +09000010 00000000 +09000014 ff000000 +09000018 81000000 +#Flush PBL data +09138000 00000000 +091380c0 00000000 diff --git a/board/freescale/t4rdb/t4_rcw.cfg b/board/freescale/t4rdb/t4_rcw.cfg new file mode 100644 index 0000000000..13408bd01f --- /dev/null +++ b/board/freescale/t4rdb/t4_rcw.cfg @@ -0,0 +1,7 @@ +#PBL preamble and RCW header +aa55aa55 010e0100 +#serdes protocol 28_56_2_10 +16070019 18101916 00000000 00000000 +70701050 00448c00 6c020000 f5000000 +00000000 ee0000ee 00000000 000287fc +00000000 50000000 00000000 00000028 diff --git a/board/freescale/t4rdb/t4rdb.h b/board/freescale/t4rdb/t4rdb.h new file mode 100644 index 0000000000..fb25d43291 --- /dev/null +++ b/board/freescale/t4rdb/t4rdb.h @@ -0,0 +1,18 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __T4RDB_H__ +#define __T4RDB_H__ + +#undef CONFIG_SYS_NUM_FM1_DTSEC +#undef CONFIG_SYS_NUM_FM2_DTSEC +#define CONFIG_SYS_NUM_FM1_DTSEC 4 +#define CONFIG_SYS_NUM_FM2_DTSEC 4 + +void fdt_fixup_board_enet(void *blob); +void pci_of_setup(void *blob, bd_t *bd); + +#endif diff --git a/board/freescale/t4rdb/tlb.c b/board/freescale/t4rdb/tlb.c new file mode 100644 index 0000000000..4b50bcd09b --- /dev/null +++ b/board/freescale/t4rdb/tlb.c @@ -0,0 +1,111 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ +#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) + /* + * *I*G - L3SRAM. When L3 is used as 512K SRAM */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_512K, 1), +#else + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#endif + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + + /* *I*G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x40000000, + CONFIG_SYS_PCIE1_MEM_PHYS + 0x40000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x50000000, + CONFIG_SYS_PCIE1_MEM_PHYS + 0x50000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256K, 1), + + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 9, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 11, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 12, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 13, BOOKE_PAGESZ_32M, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE + /* + * *I*G - NAND + * entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so we use entry 16 for nand. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 16, BOOKE_PAGESZ_64K, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c index c130e2c1ed..031367d97a 100644 --- a/board/gateworks/gw_ventana/gw_ventana.c +++ b/board/gateworks/gw_ventana/gw_ventana.c @@ -12,6 +12,7 @@ #include <asm/arch/imx-regs.h> #include <asm/arch/iomux.h> #include <asm/arch/mx6-pins.h> +#include <asm/arch/mxc_hdmi.h> #include <asm/arch/crm_regs.h> #include <asm/arch/sys_proto.h> #include <asm/gpio.h> @@ -19,6 +20,7 @@ #include <asm/imx-common/mxc_i2c.h> #include <asm/imx-common/boot_mode.h> #include <asm/imx-common/sata.h> +#include <asm/imx-common/video.h> #include <jffs2/load_kernel.h> #include <hwconfig.h> #include <i2c.h> @@ -30,8 +32,8 @@ #include <mtd_node.h> #include <netdev.h> #include <power/pmic.h> +#include <power/ltc3676_pmic.h> #include <power/pfuze100_pmic.h> -#include <i2c.h> #include <fdt_support.h> #include <jffs2/load_kernel.h> #include <spi_flash.h> @@ -369,6 +371,134 @@ int board_eth_init(bd_t *bis) return 0; } +#if defined(CONFIG_VIDEO_IPUV3) + +static void enable_hdmi(struct display_info_t const *dev) +{ + imx_enable_hdmi_phy(); +} + +static int detect_i2c(struct display_info_t const *dev) +{ + return i2c_set_bus_num(dev->bus) == 0 && + i2c_probe(dev->addr) == 0; +} + +static void enable_lvds(struct display_info_t const *dev) +{ + struct iomuxc *iomux = (struct iomuxc *) + IOMUXC_BASE_ADDR; + + /* set CH0 data width to 24bit (IOMUXC_GPR2:5 0=18bit, 1=24bit) */ + u32 reg = readl(&iomux->gpr[2]); + reg |= IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT; + writel(reg, &iomux->gpr[2]); + + /* Enable Backlight */ + imx_iomux_v3_setup_pad(MX6_PAD_SD1_CMD__GPIO1_IO18 | + MUX_PAD_CTRL(NO_PAD_CTRL)); + gpio_direction_output(IMX_GPIO_NR(1, 18), 1); +} + +struct display_info_t const displays[] = {{ + /* HDMI Output */ + .bus = -1, + .addr = 0, + .pixfmt = IPU_PIX_FMT_RGB24, + .detect = detect_hdmi, + .enable = enable_hdmi, + .mode = { + .name = "HDMI", + .refresh = 60, + .xres = 1024, + .yres = 768, + .pixclock = 15385, + .left_margin = 220, + .right_margin = 40, + .upper_margin = 21, + .lower_margin = 7, + .hsync_len = 60, + .vsync_len = 10, + .sync = FB_SYNC_EXT, + .vmode = FB_VMODE_NONINTERLACED +} }, { + /* Freescale MXC-LVDS1: HannStar HSD100PXN1-A00 w/ egalx_ts cont */ + .bus = 2, + .addr = 0x4, + .pixfmt = IPU_PIX_FMT_LVDS666, + .detect = detect_i2c, + .enable = enable_lvds, + .mode = { + .name = "Hannstar-XGA", + .refresh = 60, + .xres = 1024, + .yres = 768, + .pixclock = 15385, + .left_margin = 220, + .right_margin = 40, + .upper_margin = 21, + .lower_margin = 7, + .hsync_len = 60, + .vsync_len = 10, + .sync = FB_SYNC_EXT, + .vmode = FB_VMODE_NONINTERLACED +} } }; +size_t display_count = ARRAY_SIZE(displays); + +static void setup_display(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; + int reg; + + enable_ipu_clock(); + imx_setup_hdmi(); + /* Turn on LDB0,IPU,IPU DI0 clocks */ + reg = __raw_readl(&mxc_ccm->CCGR3); + reg |= MXC_CCM_CCGR3_LDB_DI0_MASK; + writel(reg, &mxc_ccm->CCGR3); + + /* set LDB0, LDB1 clk select to 011/011 */ + reg = readl(&mxc_ccm->cs2cdr); + reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK + |MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); + reg |= (3<<MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) + |(3<<MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET); + writel(reg, &mxc_ccm->cs2cdr); + + reg = readl(&mxc_ccm->cscmr2); + reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV; + writel(reg, &mxc_ccm->cscmr2); + + reg = readl(&mxc_ccm->chsccdr); + reg |= (CHSCCDR_CLK_SEL_LDB_DI0 + <<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); + writel(reg, &mxc_ccm->chsccdr); + + reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES + |IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH + |IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW + |IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG + |IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT + |IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG + |IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT + |IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED + |IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0; + writel(reg, &iomux->gpr[2]); + + reg = readl(&iomux->gpr[3]); + reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK) + | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 + <<IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET); + writel(reg, &iomux->gpr[3]); + + /* Backlight CABEN on LVDS connector */ + imx_iomux_v3_setup_pad(MX6_PAD_SD2_CLK__GPIO1_IO10 | + MUX_PAD_CTRL(NO_PAD_CTRL)); + gpio_direction_output(IMX_GPIO_NR(1, 10), 0); +} +#endif /* CONFIG_VIDEO_IPUV3 */ + /* read ventana EEPROM, check for validity, and return baseboard type */ static int read_eeprom(void) @@ -733,6 +863,62 @@ struct ventana gpio_cfg[] = { }, }; +/* setup board specific PMIC */ +int power_init_board(void) +{ + struct pmic *p; + u32 reg; + + /* configure PFUZE100 PMIC */ + if (board_type == GW54xx || board_type == GW54proto) { + power_pfuze100_init(I2C_PMIC); + p = pmic_get("PFUZE100_PMIC"); + if (p && !pmic_probe(p)) { + pmic_reg_read(p, PFUZE100_DEVICEID, ®); + printf("PMIC: PFUZE100 ID=0x%02x\n", reg); + + /* Set VGEN1 to 1.5V and enable */ + pmic_reg_read(p, PFUZE100_VGEN1VOL, ®); + reg &= ~(LDO_VOL_MASK); + reg |= (LDOA_1_50V | LDO_EN); + pmic_reg_write(p, PFUZE100_VGEN1VOL, reg); + + /* Set SWBST to 5.0V and enable */ + pmic_reg_read(p, PFUZE100_SWBSTCON1, ®); + reg &= ~(SWBST_MODE_MASK | SWBST_VOL_MASK); + reg |= (SWBST_5_00V | SWBST_MODE_AUTO); + pmic_reg_write(p, PFUZE100_SWBSTCON1, reg); + } + } + + /* configure LTC3676 PMIC */ + else { + power_ltc3676_init(I2C_PMIC); + p = pmic_get("LTC3676_PMIC"); + if (p && !pmic_probe(p)) { + puts("PMIC: LTC3676\n"); + /* set board-specific scalar to 1225mV for IMX6Q@1GHz */ + if (is_cpu_type(MXC_CPU_MX6Q)) { + /* mask PGOOD during SW1 transition */ + reg = 0x1d | LTC3676_PGOOD_MASK; + pmic_reg_write(p, LTC3676_DVB1B, reg); + /* set SW1 (VDD_SOC) to 1259mV */ + reg = 0x1d; + pmic_reg_write(p, LTC3676_DVB1A, reg); + + /* mask PGOOD during SW3 transition */ + reg = 0x1d | LTC3676_PGOOD_MASK; + pmic_reg_write(p, LTC3676_DVB3B, reg); + /*set SW3 (VDD_ARM) to 1259mV */ + reg = 0x1d; + pmic_reg_write(p, LTC3676_DVB3A, reg); + } + } + } + + return 0; +} + /* setup GPIO pinmux and default configuration per baseboard */ static void setup_board_gpio(int board) { @@ -888,6 +1074,9 @@ int board_early_init_f(void) setup_iomux_uart(); gpio_direction_output(GP_USB_OTG_PWR, 0); /* OTG power off */ +#if defined(CONFIG_VIDEO_IPUV3) + setup_display(); +#endif return 0; } @@ -1076,28 +1265,6 @@ int misc_init_r(void) setenv("serial#", str); } - /* configure PFUZE100 PMIC (not used on all Ventana baseboards) */ - if ((board_type == GW54xx || board_type == GW54proto) && - !pmic_init(I2C_PMIC)) { - struct pmic *p = pmic_get("PFUZE100_PMIC"); - u32 reg; - if (p && !pmic_probe(p)) { - pmic_reg_read(p, PFUZE100_DEVICEID, ®); - printf("PMIC: PFUZE100 ID=0x%02x\n", reg); - - /* Set VGEN1 to 1.5V and enable */ - pmic_reg_read(p, PFUZE100_VGEN1VOL, ®); - reg &= ~(LDO_VOL_MASK); - reg |= (LDOA_1_50V | LDO_EN); - pmic_reg_write(p, PFUZE100_VGEN1VOL, reg); - - /* Set SWBST to 5.0V and enable */ - pmic_reg_read(p, PFUZE100_SWBSTCON1, ®); - reg &= ~(SWBST_MODE_MASK | SWBST_VOL_MASK); - reg |= (SWBST_5_00V | SWBST_MODE_AUTO); - pmic_reg_write(p, PFUZE100_SWBSTCON1, reg); - } - } /* setup baseboard specific GPIO pinmux and config */ setup_board_gpio(board_type); @@ -1243,7 +1410,7 @@ void ft_board_setup(void *blob, bd_t *bd) /* board serial number */ fdt_setprop(blob, 0, "system-serial", getenv("serial#"), - strlen(getenv("serial#") + 1)); + strlen(getenv("serial#")) + 1); /* board (model contains model from device-tree) */ fdt_setprop(blob, 0, "board", info->model, diff --git a/board/gateworks/gw_ventana/ventana_eeprom.h b/board/gateworks/gw_ventana/ventana_eeprom.h index d310bfd994..434b604542 100644 --- a/board/gateworks/gw_ventana/ventana_eeprom.h +++ b/board/gateworks/gw_ventana/ventana_eeprom.h @@ -16,16 +16,16 @@ struct ventana_board_info { u8 mfgdate[4]; /* 0x20: MFG date (read only) */ u8 res2[7]; /* 0x24 */ /* sdram config */ - u8 sdram_size; /* 0x2B: enum (512,1024,2048) MB */ - u8 sdram_speed; /* 0x2C: enum (100,133,166,200,267,333,400) MHz */ - u8 sdram_width; /* 0x2D: enum (32,64) bit */ + u8 sdram_size; /* 0x2B: (16 << n) MB */ + u8 sdram_speed; /* 0x2C: (33.333 * n) MHz */ + u8 sdram_width; /* 0x2D: (8 << n) bit */ /* cpu config */ - u8 cpu_speed; /* 0x2E: enum (800,1000,1200) MHz */ - u8 cpu_type; /* 0x2F: enum (imx6q,imx6d,imx6dl,imx6s) */ + u8 cpu_speed; /* 0x2E: (33.333 * n) MHz */ + u8 cpu_type; /* 0x2F: 7=imx6q, 8=imx6dl */ u8 model[16]; /* 0x30: model string */ /* FLASH config */ - u8 nand_flash_size; /* 0x40: enum (4,8,16,32,64,128) MB */ - u8 spi_flash_size; /* 0x41: enum (4,8,16,32,64,128) MB */ + u8 nand_flash_size; /* 0x40: (8 << (n-1)) MB */ + u8 spi_flash_size; /* 0x41: (4 << (n-1)) MB */ /* Config1: SoC Peripherals */ u8 config[8]; /* 0x42: loading options */ diff --git a/board/gumstix/pepper/Makefile b/board/gumstix/pepper/Makefile new file mode 100644 index 0000000000..ecb1d61669 --- /dev/null +++ b/board/gumstix/pepper/Makefile @@ -0,0 +1,13 @@ +# +# Makefile +# +# Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ +# +# SPDX-License-Identifier: GPL-2.0+ +# + +ifdef CONFIG_SPL_BUILD +obj-y += mux.o +endif + +obj-y += board.o diff --git a/board/gumstix/pepper/board.c b/board/gumstix/pepper/board.c new file mode 100644 index 0000000000..75aac49fd0 --- /dev/null +++ b/board/gumstix/pepper/board.c @@ -0,0 +1,226 @@ +/* + * Board functions for Gumstix Pepper and AM335x-based boards + * + * Copyright (C) 2014, Gumstix, Incorporated - http://www.gumstix.com/ + * Based on board/ti/am335x/board.c from Texas Instruments, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <errno.h> +#include <spl.h> +#include <asm/arch/cpu.h> +#include <asm/arch/hardware.h> +#include <asm/arch/omap.h> +#include <asm/arch/ddr_defs.h> +#include <asm/arch/clock.h> +#include <asm/arch/gpio.h> +#include <asm/arch/mmc_host_def.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/mem.h> +#include <asm/io.h> +#include <asm/emif.h> +#include <asm/gpio.h> +#include <i2c.h> +#include <miiphy.h> +#include <cpsw.h> +#include <power/tps65217.h> +#include <environment.h> +#include <watchdog.h> +#include "board.h" + +DECLARE_GLOBAL_DATA_PTR; + +#ifdef CONFIG_SPL_BUILD +static const struct ddr_data ddr2_data = { + .datardsratio0 = ((MT47H128M16RT25E_RD_DQS<<30) | + (MT47H128M16RT25E_RD_DQS<<20) | + (MT47H128M16RT25E_RD_DQS<<10) | + (MT47H128M16RT25E_RD_DQS<<0)), + .datawdsratio0 = ((MT47H128M16RT25E_WR_DQS<<30) | + (MT47H128M16RT25E_WR_DQS<<20) | + (MT47H128M16RT25E_WR_DQS<<10) | + (MT47H128M16RT25E_WR_DQS<<0)), + .datawiratio0 = ((MT47H128M16RT25E_PHY_WRLVL<<30) | + (MT47H128M16RT25E_PHY_WRLVL<<20) | + (MT47H128M16RT25E_PHY_WRLVL<<10) | + (MT47H128M16RT25E_PHY_WRLVL<<0)), + .datagiratio0 = ((MT47H128M16RT25E_PHY_GATELVL<<30) | + (MT47H128M16RT25E_PHY_GATELVL<<20) | + (MT47H128M16RT25E_PHY_GATELVL<<10) | + (MT47H128M16RT25E_PHY_GATELVL<<0)), + .datafwsratio0 = ((MT47H128M16RT25E_PHY_FIFO_WE<<30) | + (MT47H128M16RT25E_PHY_FIFO_WE<<20) | + (MT47H128M16RT25E_PHY_FIFO_WE<<10) | + (MT47H128M16RT25E_PHY_FIFO_WE<<0)), + .datawrsratio0 = ((MT47H128M16RT25E_PHY_WR_DATA<<30) | + (MT47H128M16RT25E_PHY_WR_DATA<<20) | + (MT47H128M16RT25E_PHY_WR_DATA<<10) | + (MT47H128M16RT25E_PHY_WR_DATA<<0)), +}; + +static const struct cmd_control ddr2_cmd_ctrl_data = { + .cmd0csratio = MT47H128M16RT25E_RATIO, + .cmd0iclkout = MT47H128M16RT25E_INVERT_CLKOUT, + + .cmd1csratio = MT47H128M16RT25E_RATIO, + .cmd1iclkout = MT47H128M16RT25E_INVERT_CLKOUT, + + .cmd2csratio = MT47H128M16RT25E_RATIO, + .cmd2iclkout = MT47H128M16RT25E_INVERT_CLKOUT, +}; + +static const struct emif_regs ddr2_emif_reg_data = { + .sdram_config = MT47H128M16RT25E_EMIF_SDCFG, + .ref_ctrl = MT47H128M16RT25E_EMIF_SDREF, + .sdram_tim1 = MT47H128M16RT25E_EMIF_TIM1, + .sdram_tim2 = MT47H128M16RT25E_EMIF_TIM2, + .sdram_tim3 = MT47H128M16RT25E_EMIF_TIM3, + .emif_ddr_phy_ctlr_1 = MT47H128M16RT25E_EMIF_READ_LATENCY, +}; + +#ifdef CONFIG_SPL_OS_BOOT +int spl_start_uboot(void) +{ + /* break into full u-boot on 'c' */ + return serial_tstc() && serial_getc() == 'c'; +} +#endif + +#define OSC (V_OSCK/1000000) +const struct dpll_params dpll_ddr = {266, OSC-1, 1, -1, -1, -1, -1}; + +const struct dpll_params *get_dpll_ddr_params(void) +{ + return &dpll_ddr; +} + +void set_uart_mux_conf(void) +{ + enable_uart0_pin_mux(); +} + +void set_mux_conf_regs(void) +{ + enable_board_pin_mux(); +} + +const struct ctrl_ioregs ioregs = { + .cm0ioctl = MT47H128M16RT25E_IOCTRL_VALUE, + .cm1ioctl = MT47H128M16RT25E_IOCTRL_VALUE, + .cm2ioctl = MT47H128M16RT25E_IOCTRL_VALUE, + .dt0ioctl = MT47H128M16RT25E_IOCTRL_VALUE, + .dt1ioctl = MT47H128M16RT25E_IOCTRL_VALUE, +}; + +void sdram_init(void) +{ + config_ddr(266, &ioregs, &ddr2_data, + &ddr2_cmd_ctrl_data, &ddr2_emif_reg_data, 0); +} +#endif + +int board_init(void) +{ +#if defined(CONFIG_HW_WATCHDOG) + hw_watchdog_init(); +#endif + + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + gpmc_init(); + + return 0; +} + +#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ + (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) +static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; + +static void cpsw_control(int enabled) +{ + /* VTP can be added here */ + + return; +} + +static struct cpsw_slave_data cpsw_slaves[] = { + { + .slave_reg_ofs = 0x208, + .sliver_reg_ofs = 0xd80, + .phy_addr = 0, + .phy_if = PHY_INTERFACE_MODE_RGMII, + }, +}; + +static struct cpsw_platform_data cpsw_data = { + .mdio_base = CPSW_MDIO_BASE, + .cpsw_base = CPSW_BASE, + .mdio_div = 0xff, + .channels = 8, + .cpdma_reg_ofs = 0x800, + .slaves = 1, + .slave_data = cpsw_slaves, + .ale_reg_ofs = 0xd00, + .ale_entries = 1024, + .host_port_reg_ofs = 0x108, + .hw_stats_reg_ofs = 0x900, + .bd_ram_ofs = 0x2000, + .mac_control = (1 << 5), + .control = cpsw_control, + .host_port_num = 0, + .version = CPSW_CTRL_VERSION_2, +}; + +int board_eth_init(bd_t *bis) +{ + int rv, n = 0; + uint8_t mac_addr[6]; + uint32_t mac_hi, mac_lo; + const char *devname; + + if (!eth_getenv_enetaddr("ethaddr", mac_addr)) { + /* try reading mac address from efuse */ + mac_lo = readl(&cdev->macid0l); + mac_hi = readl(&cdev->macid0h); + mac_addr[0] = mac_hi & 0xFF; + mac_addr[1] = (mac_hi & 0xFF00) >> 8; + mac_addr[2] = (mac_hi & 0xFF0000) >> 16; + mac_addr[3] = (mac_hi & 0xFF000000) >> 24; + mac_addr[4] = mac_lo & 0xFF; + mac_addr[5] = (mac_lo & 0xFF00) >> 8; + if (is_valid_ether_addr(mac_addr)) + eth_setenv_enetaddr("ethaddr", mac_addr); + } + + writel((RGMII_MODE_ENABLE | RGMII_INT_DELAY), &cdev->miisel); + + rv = cpsw_register(&cpsw_data); + if (rv < 0) + printf("Error %d registering CPSW switch\n", rv); + else + n += rv; + + /* + * + * CPSW RGMII Internal Delay Mode is not supported in all PVT + * operating points. So we must set the TX clock delay feature + * in the KSZ9021 PHY. Since we only support a single ethernet + * device in U-Boot, we only do this for the current instance. + */ + devname = miiphy_get_current_dev(); + /* max rx/tx clock delay, min rx/tx control delay */ + miiphy_write(devname, 0x0, 0x0b, 0x8104); + miiphy_write(devname, 0x0, 0xc, 0xa0a0); + + /* min rx data delay */ + miiphy_write(devname, 0x0, 0x0b, 0x8105); + miiphy_write(devname, 0x0, 0x0c, 0x0000); + + /* min tx data delay */ + miiphy_write(devname, 0x0, 0x0b, 0x8106); + miiphy_write(devname, 0x0, 0x0c, 0x0000); + + return n; +} +#endif diff --git a/board/gumstix/pepper/board.h b/board/gumstix/pepper/board.h new file mode 100644 index 0000000000..0512735a7b --- /dev/null +++ b/board/gumstix/pepper/board.h @@ -0,0 +1,19 @@ +/* + * Gumstix Pepper and AM335x-based boards information header + * + * Copyright (C) 2014, Gumstix, Inc. - http://www.gumstix.com/ + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _BOARD_H_ +#define _BOARD_H_ + +/* + * We must be able to enable uart0, for initial output. We then have a + * main pinmux function that can be overridden to enable all other pinmux that + * is required on the board. + */ +void enable_uart0_pin_mux(void); +void enable_board_pin_mux(void); +#endif diff --git a/board/gumstix/pepper/mux.c b/board/gumstix/pepper/mux.c new file mode 100644 index 0000000000..50b12666d6 --- /dev/null +++ b/board/gumstix/pepper/mux.c @@ -0,0 +1,78 @@ +/* + * Muxing for Gumstix Pepper and AM335x-based boards + * + * Copyright (C) 2014, Gumstix, Incorporated - http://www.gumstix.com/ + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#include <common.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/hardware.h> +#include <asm/arch/mux.h> +#include <asm/io.h> +#include <i2c.h> +#include "board.h" + +static struct module_pin_mux uart0_pin_mux[] = { + {OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* UART0_RXD */ + {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, /* UART0_TXD */ + {-1}, +}; + +static struct module_pin_mux mmc0_pin_mux[] = { + {OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT3 */ + {OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT2 */ + {OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT1 */ + {OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT0 */ + {OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CLK */ + {OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CMD */ + {OFFSET(spi0_cs1), (MODE(5) | RXACTIVE | PULLUP_EN)}, /* MMC0_CD */ + {-1}, +}; + +static struct module_pin_mux i2c0_pin_mux[] = { + /* I2C_DATA */ + {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)}, + /* I2C_SCLK */ + {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)}, + {-1}, +}; + +static struct module_pin_mux rgmii1_pin_mux[] = { + {OFFSET(mii1_txen), MODE(2)}, /* RGMII1_TCTL */ + {OFFSET(mii1_rxdv), MODE(2) | RXACTIVE}, /* RGMII1_RCTL */ + {OFFSET(mii1_txd3), MODE(2)}, /* RGMII1_TD3 */ + {OFFSET(mii1_txd2), MODE(2)}, /* RGMII1_TD2 */ + {OFFSET(mii1_txd1), MODE(2)}, /* RGMII1_TD1 */ + {OFFSET(mii1_txd0), MODE(2)}, /* RGMII1_TD0 */ + {OFFSET(mii1_txclk), MODE(2)}, /* RGMII1_TCLK */ + {OFFSET(mii1_rxclk), MODE(2) | RXACTIVE}, /* RGMII1_RCLK */ + {OFFSET(mii1_rxd3), MODE(2) | RXACTIVE}, /* RGMII1_RD3 */ + {OFFSET(mii1_rxd2), MODE(2) | RXACTIVE}, /* RGMII1_RD2 */ + {OFFSET(mii1_rxd1), MODE(2) | RXACTIVE}, /* RGMII1_RD1 */ + {OFFSET(mii1_rxd0), MODE(2) | RXACTIVE}, /* RGMII1_RD0 */ + {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */ + {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */ + {OFFSET(rmii1_refclk), MODE(7) | RXACTIVE}, /* ETH_INT */ + {OFFSET(mii1_col), MODE(7) | PULLUP_EN}, /* PHY_NRESET */ + {OFFSET(xdma_event_intr1), MODE(3)}, + {-1}, +}; + +void enable_uart0_pin_mux(void) +{ + configure_module_pin_mux(uart0_pin_mux); +} + +/* + * Do board-specific muxes. + */ +void enable_board_pin_mux(void) +{ + /* I2C0 */ + configure_module_pin_mux(i2c0_pin_mux); + /* SD Card */ + configure_module_pin_mux(mmc0_pin_mux); + /* Ethernet pinmux. */ + configure_module_pin_mux(rgmii1_pin_mux); +} diff --git a/board/keymile/kmp204x/kmp204x.c b/board/keymile/kmp204x/kmp204x.c index 95a19cdb2c..6bc8eb85ea 100644 --- a/board/keymile/kmp204x/kmp204x.c +++ b/board/keymile/kmp204x/kmp204x.c @@ -79,7 +79,7 @@ int get_scl(void) #define ZL30158_RST 8 -#define ZL30343_RST 9 +#define BFTIC4_RST 0 int board_early_init_f(void) { @@ -88,13 +88,15 @@ int board_early_init_f(void) /* board only uses the DDR_MCK0, so disable the DDR_MCK1/2/3 */ setbits_be32(&gur->ddrclkdr, 0x001f000f); - /* take the Zarlinks out of reset as soon as possible */ - qrio_prst(ZL30158_RST, false, false); - qrio_prst(ZL30343_RST, false, false); + /* set the BFTIC's prstcfg to reset at power-up and unit reset only */ + qrio_prstcfg(BFTIC4_RST, PRSTCFG_POWUP_UNIT_RST); + /* and enable WD on it */ + qrio_wdmask(BFTIC4_RST, true); - /* and set their reset to power-up only */ - qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_RST); - qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_RST); + /* set the ZL30138's prstcfg to reset at power-up and unit reset only */ + qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_UNIT_RST); + /* and take it out of reset as soon as possible (needed for Hooper) */ + qrio_prst(ZL30158_RST, false, false); return 0; } @@ -113,6 +115,12 @@ int board_early_init_r(void) if (ret) printf("error triggering PCIe FPGA config\n"); + /* enable the Unit LED (red) & Boot LED (on) */ + qrio_set_leds(); + + /* enable Application Buffer */ + qrio_enable_app_buffer(); + return ret; } @@ -121,16 +129,37 @@ unsigned long get_board_sys_clk(unsigned long dummy) return 66666666; } +#define ETH_FRONT_PHY_RST 15 +#define QSFP2_RST 11 +#define QSFP1_RST 10 +#define ZL30343_RST 9 + int misc_init_f(void) { /* configure QRIO pis for i2c deblocking */ i2c_deblock_gpio_cfg(); + /* configure the front phy's prstcfg and take it out of reset */ + qrio_prstcfg(ETH_FRONT_PHY_RST, PRSTCFG_POWUP_UNIT_CORE_RST); + qrio_prst(ETH_FRONT_PHY_RST, false, false); + + /* set the ZL30343 prstcfg to reset at power-up and unit reset only */ + qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_UNIT_RST); + /* and enable the WD on it */ + qrio_wdmask(ZL30343_RST, true); + + /* set the QSFPs' prstcfg to reset at power-up and unit rst only */ + qrio_prstcfg(QSFP1_RST, PRSTCFG_POWUP_UNIT_RST); + qrio_prstcfg(QSFP2_RST, PRSTCFG_POWUP_UNIT_RST); + + /* and enable the WD on them */ + qrio_wdmask(QSFP1_RST, true); + qrio_wdmask(QSFP2_RST, true); + return 0; } #define NUM_SRDS_BANKS 2 -#define PHY_RST 15 int misc_init_r(void) { @@ -151,9 +180,6 @@ int misc_init_r(void) } } - /* take the mgmt eth phy out of reset */ - qrio_prst(PHY_RST, false, false); - return 0; } @@ -166,9 +192,23 @@ int hush_init_var(void) #endif #if defined(CONFIG_LAST_STAGE_INIT) + int last_stage_init(void) { +#if defined(CONFIG_KMCOGE4) + /* on KMCOGE4, the BFTIC4 is on the LBAPP2 */ + struct bfticu_iomap *bftic4 = + (struct bfticu_iomap *)CONFIG_SYS_LBAPP2_BASE; + u8 dip_switch = in_8((u8 *)&(bftic4->mswitch)) & BFTICU_DIPSWITCH_MASK; + + if (dip_switch != 0) { + /* start bootloader */ + puts("DIP: Enabled\n"); + setenv("actual_bank", "0"); + } +#endif set_km_env(); + return 0; } #endif @@ -232,3 +272,16 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_mac_addresses(blob); #endif } + +#if defined(CONFIG_POST) + +/* DIC26_SELFTEST GPIO used to start factory test sw */ +#define SELFTEST_PORT GPIO_A +#define SELFTEST_PIN 31 + +int post_hotkeys_pressed(void) +{ + qrio_gpio_direction_input(SELFTEST_PORT, SELFTEST_PIN); + return qrio_get_gpio(SELFTEST_PORT, SELFTEST_PIN); +} +#endif diff --git a/board/keymile/kmp204x/kmp204x.h b/board/keymile/kmp204x/kmp204x.h index 0267596e4e..afede994f1 100644 --- a/board/keymile/kmp204x/kmp204x.h +++ b/board/keymile/kmp204x/kmp204x.h @@ -20,6 +20,9 @@ void qrio_gpio_direction_input(u8 port_off, u8 gpio_nr); #define PRSTCFG_POWUP_RST 0x3 void qrio_prst(u8 bit, bool en, bool wden); +void qrio_wdmask(u8 bit, bool wden); void qrio_prstcfg(u8 bit, u8 mode); +void qrio_set_leds(void); +void qrio_enable_app_buffer(void); void pci_of_setup(void *blob, bd_t *bd); diff --git a/board/keymile/kmp204x/pbi.cfg b/board/keymile/kmp204x/pbi.cfg index 9af8bd5b57..1e0a171d88 100644 --- a/board/keymile/kmp204x/pbi.cfg +++ b/board/keymile/kmp204x/pbi.cfg @@ -8,16 +8,47 @@ # #PBI commands -#Workaround for A-006559 needed for rev 2.0 of P2041 silicon -#Freescale's errarta sheet suggests it may be done with PBI +#Configure ALTCBAR for DCSR -> DCSR@89000000 +091380c0 000009C4 09000010 00000000 +091380c0 000009C4 09000014 00000000 +091380c0 000009C4 09000018 81d00000 -09021008 0000f000 -09021028 0000f000 -09021048 0000f000 -09021068 0000f000 +#Workaround for A-004849 +091380c0 000009C4 +890B0050 00000002 +091380c0 000009C4 +890B0054 00000002 +091380c0 000009C4 +890B0058 00000002 +091380c0 000009C4 +890B005C 00000002 +091380c0 000009C4 +890B0090 00000002 +091380c0 000009C4 +890B0094 00000002 +091380c0 000009C4 +890B0098 00000002 +091380c0 000009C4 +890B009C 00000002 +091380c0 000009C4 +890B0108 00000012 +091380c0 000009C4 +#Workaround for A-006559 needed for rev 2.0 of P2041 silicon +89021008 0000f000 +091380c0 000009C4 +89021028 0000f000 +091380c0 000009C4 +89021048 0000f000 +091380c0 000009C4 +89021068 0000f000 +091380c0 000009C4 +#Flush PBL data +09138000 00000000 +#Disable ALTCBAR 09000018 00000000 +091380c0 000009C4 #Initialize CPC1 as 1MB SRAM 09010000 00200400 09138000 00000000 diff --git a/board/keymile/kmp204x/pci.c b/board/keymile/kmp204x/pci.c index a484eb5749..2b0b054a11 100644 --- a/board/keymile/kmp204x/pci.c +++ b/board/keymile/kmp204x/pci.c @@ -94,20 +94,23 @@ err_out: } #define PCIE_SW_RST 14 -#define PEXHC_SW_RST 13 -#define HOOPER_SW_RST 12 +#define PEXHC_RST 13 +#define HOOPER_RST 12 void pci_init_board(void) { - /* first wait for the PCIe FPGA to be configured + qrio_prstcfg(PCIE_SW_RST, PRSTCFG_POWUP_UNIT_CORE_RST); + qrio_prstcfg(PEXHC_RST, PRSTCFG_POWUP_UNIT_CORE_RST); + qrio_prstcfg(HOOPER_RST, PRSTCFG_POWUP_UNIT_CORE_RST); + + /* wait for the PCIe FPGA to be configured * it has been triggered earlier in board_early_init_r */ - int ret = wait_for_fpga_config(); - if (ret) + if (wait_for_fpga_config()) printf("error finishing PCIe FPGA config\n"); qrio_prst(PCIE_SW_RST, false, false); - qrio_prst(PEXHC_SW_RST, false, false); - qrio_prst(HOOPER_SW_RST, false, false); + qrio_prst(PEXHC_RST, false, false); + qrio_prst(HOOPER_RST, false, false); /* Hooper is not direcly PCIe capable */ mdelay(50); diff --git a/board/keymile/kmp204x/qrio.c b/board/keymile/kmp204x/qrio.c index 49f9aa2546..b6ba93ada8 100644 --- a/board/keymile/kmp204x/qrio.c +++ b/board/keymile/kmp204x/qrio.c @@ -91,7 +91,7 @@ void qrio_set_opendrain_gpio(u8 port_off, u8 gpio_nr, u8 val) #define WDMASK_OFF 0x16 -static void qrio_wdmask(u8 bit, bool wden) +void qrio_wdmask(u8 bit, bool wden) { u16 wdmask; void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; @@ -144,3 +144,32 @@ void qrio_prstcfg(u8 bit, u8 mode) out_be32(qrio_base + PRSTCFG_OFF, prstcfg); } + +#define CTRLH_OFF 0x02 +#define CTRLH_WRL_BOOT 0x01 +#define CTRLH_WRL_UNITRUN 0x02 + +void qrio_set_leds(void) +{ + u8 ctrlh; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + /* set UNIT LED to RED and BOOT LED to ON */ + ctrlh = in_8(qrio_base + CTRLH_OFF); + ctrlh |= (CTRLH_WRL_BOOT | CTRLH_WRL_UNITRUN); + out_8(qrio_base + CTRLH_OFF, ctrlh); +} + +#define CTRLL_OFF 0x03 +#define CTRLL_WRB_BUFENA 0x20 + +void qrio_enable_app_buffer(void) +{ + u8 ctrll; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + /* enable application buffer */ + ctrll = in_8(qrio_base + CTRLL_OFF); + ctrll |= (CTRLL_WRB_BUFENA); + out_8(qrio_base + CTRLL_OFF, ctrll); +} diff --git a/board/keymile/kmp204x/rcw_kmp204x.cfg b/board/keymile/kmp204x/rcw_kmp204x.cfg index 2d4c48cb9c..236d5138bc 100644 --- a/board/keymile/kmp204x/rcw_kmp204x.cfg +++ b/board/keymile/kmp204x/rcw_kmp204x.cfg @@ -7,5 +7,5 @@ aa55aa55 010e0100 #64 bytes RCW data 14600000 00000000 28200000 00000000 148E70CF CFC02000 58000000 41000000 -00000000 00000000 00000000 F0428002 +00000000 00000000 00000000 F0428816 00000000 00000000 00000000 00000000 diff --git a/board/matrix_vision/common/mv_common.c b/board/matrix_vision/common/mv_common.c index 70133b5118..1be5aba2e9 100644 --- a/board/matrix_vision/common/mv_common.c +++ b/board/matrix_vision/common/mv_common.c @@ -77,7 +77,7 @@ int mv_load_fpga(void) return -1; } - result = fpga_load(0, fpga_data, data_size); + result = fpga_load(0, fpga_data, data_size, BIT_FULL); if (!result) bootstage_mark(BOOTSTAGE_ID_START); diff --git a/board/nvidia/jetson-tk1/jetson-tk1.c b/board/nvidia/jetson-tk1/jetson-tk1.c index f97aafad42..5d37718f3b 100644 --- a/board/nvidia/jetson-tk1/jetson-tk1.c +++ b/board/nvidia/jetson-tk1/jetson-tk1.c @@ -6,6 +6,7 @@ */ #include <common.h> +#include <asm/arch/gpio.h> #include <asm/arch/pinmux.h> #include "pinmux-config-jetson-tk1.h" @@ -15,6 +16,11 @@ */ void pinmux_init(void) { + pinmux_set_tristate_input_clamping(); + + gpio_config_table(jetson_tk1_gpio_inits, + ARRAY_SIZE(jetson_tk1_gpio_inits)); + pinmux_config_pingrp_table(jetson_tk1_pingrps, ARRAY_SIZE(jetson_tk1_pingrps)); diff --git a/board/nvidia/jetson-tk1/pinmux-config-jetson-tk1.h b/board/nvidia/jetson-tk1/pinmux-config-jetson-tk1.h index 1adcae4bdd..d338818a64 100644 --- a/board/nvidia/jetson-tk1/pinmux-config-jetson-tk1.h +++ b/board/nvidia/jetson-tk1/pinmux-config-jetson-tk1.h @@ -7,6 +7,98 @@ #ifndef _PINMUX_CONFIG_JETSON_TK1_H_ #define _PINMUX_CONFIG_JETSON_TK1_H_ +#define GPIO_INIT(_gpio, _init) \ + { \ + .gpio = GPIO_P##_gpio, \ + .init = TEGRA_GPIO_INIT_##_init, \ + } + +static const struct tegra_gpio_config jetson_tk1_gpio_inits[] = { + /* gpio, init_val */ + GPIO_INIT(C7, IN), + GPIO_INIT(G0, OUT0), + GPIO_INIT(G1, OUT0), + GPIO_INIT(G2, IN), + GPIO_INIT(G3, IN), + GPIO_INIT(H2, OUT0), + GPIO_INIT(H3, OUT0), + GPIO_INIT(H4, IN), + GPIO_INIT(H5, OUT0), + GPIO_INIT(H6, IN), + GPIO_INIT(H7, OUT0), + GPIO_INIT(I0, OUT0), + GPIO_INIT(I2, OUT0), + GPIO_INIT(I4, OUT0), + GPIO_INIT(I5, IN), + GPIO_INIT(I6, IN), + GPIO_INIT(J0, IN), + GPIO_INIT(J2, IN), + GPIO_INIT(K1, OUT0), + GPIO_INIT(K2, IN), + GPIO_INIT(K3, IN), + GPIO_INIT(K4, OUT0), + GPIO_INIT(K5, OUT0), + GPIO_INIT(K6, OUT0), + GPIO_INIT(N7, IN), + GPIO_INIT(O0, IN), + GPIO_INIT(O1, IN), + GPIO_INIT(O2, IN), + GPIO_INIT(O3, IN), + GPIO_INIT(O4, IN), + GPIO_INIT(O5, IN), + GPIO_INIT(O6, OUT0), + GPIO_INIT(O7, IN), + GPIO_INIT(P0, OUT0), + GPIO_INIT(P1, OUT0), + GPIO_INIT(P2, OUT0), + GPIO_INIT(Q0, IN), + GPIO_INIT(Q1, IN), + GPIO_INIT(Q2, IN), + GPIO_INIT(Q5, IN), + GPIO_INIT(Q6, IN), + GPIO_INIT(Q7, IN), + GPIO_INIT(R0, OUT0), + GPIO_INIT(R1, OUT0), + GPIO_INIT(R2, OUT0), + GPIO_INIT(R4, IN), + GPIO_INIT(R5, OUT0), + GPIO_INIT(R7, IN), + GPIO_INIT(S0, IN), + GPIO_INIT(S3, OUT0), + GPIO_INIT(S4, OUT0), + GPIO_INIT(S5, IN), + GPIO_INIT(S6, OUT0), + GPIO_INIT(T0, OUT0), + GPIO_INIT(T1, OUT0), + GPIO_INIT(U0, OUT0), + GPIO_INIT(U1, IN), + GPIO_INIT(U2, IN), + GPIO_INIT(U3, OUT0), + GPIO_INIT(U4, OUT0), + GPIO_INIT(U5, IN), + GPIO_INIT(U6, IN), + GPIO_INIT(V0, IN), + GPIO_INIT(V1, IN), + GPIO_INIT(W2, IN), + GPIO_INIT(W3, IN), + GPIO_INIT(X1, OUT0), + GPIO_INIT(X3, IN), + GPIO_INIT(X4, OUT0), + GPIO_INIT(X5, IN), + GPIO_INIT(X6, IN), + GPIO_INIT(X7, OUT0), + GPIO_INIT(BB3, OUT0), + GPIO_INIT(BB5, OUT0), + GPIO_INIT(BB6, OUT0), + GPIO_INIT(BB7, OUT0), + GPIO_INIT(CC1, IN), + GPIO_INIT(CC2, IN), + GPIO_INIT(CC5, OUT0), + GPIO_INIT(EE1, OUT0), + GPIO_INIT(FF1, OUT0), + GPIO_INIT(FF2, IN), +}; + #define PINCFG(_pingrp, _mux, _pull, _tri, _io, _od, _rcv_sel) \ { \ .pingrp = PMUX_PINGRP_##_pingrp, \ @@ -41,43 +133,43 @@ static const struct pmux_pingrp_config jetson_tk1_pingrps[] = { PINCFG(UART2_RXD_PC3, IRDA, UP, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(GEN1_I2C_SCL_PC4, I2C1, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), PINCFG(GEN1_I2C_SDA_PC5, I2C1, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), - PINCFG(PC7, RSVD1, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PG0, RSVD1, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PG1, RSVD1, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PG2, RSVD1, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PG3, RSVD1, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PC7, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PG0, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PG1, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PG2, DEFAULT, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PG3, DEFAULT, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(PG4, SPI4, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(PG5, SPI4, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(PG6, SPI4, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(PG7, SPI4, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(PH0, GMI, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), PINCFG(PH1, PWM1, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PH2, GMI, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PH3, GMI, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PH4, RSVD2, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PH5, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PH6, GMI, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PH7, GMI, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PI0, RSVD1, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PH2, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PH3, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PH4, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PH5, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PH6, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PH7, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PI0, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(PI1, RSVD1, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PI2, RSVD4, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PI2, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(PI3, SPI4, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PI4, GMI, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PI5, RSVD2, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PI6, RSVD1, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PI4, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PI5, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PI6, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(PI7, RSVD1, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PJ0, RSVD1, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PJ2, RSVD1, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PJ0, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PJ2, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(UART2_CTS_N_PJ5, UARTB, UP, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(UART2_RTS_N_PJ6, UARTB, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(PJ7, UARTD, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(PK0, SOC, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PK1, RSVD4, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PK2, RSVD1, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PK3, GMI, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PK4, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(SPDIF_OUT_PK5, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(SPDIF_IN_PK6, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PK1, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PK2, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PK3, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PK4, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(SPDIF_OUT_PK5, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(SPDIF_IN_PK6, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(PK7, UARTD, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(DAP1_FS_PN0, I2S0, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(DAP1_DIN_PN1, I2S0, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), @@ -85,79 +177,79 @@ static const struct pmux_pingrp_config jetson_tk1_pingrps[] = { PINCFG(DAP1_SCLK_PN3, I2S0, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(USB_VBUS_EN0_PN4, USB, UP, NORMAL, INPUT, ENABLE, DEFAULT), PINCFG(USB_VBUS_EN1_PN5, USB, UP, NORMAL, INPUT, ENABLE, DEFAULT), - PINCFG(HDMI_INT_PN7, RSVD1, DOWN, NORMAL, INPUT, DEFAULT, NORMAL), - PINCFG(ULPI_DATA7_PO0, ULPI, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(ULPI_DATA0_PO1, ULPI, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(ULPI_DATA1_PO2, ULPI, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(ULPI_DATA2_PO3, ULPI, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(ULPI_DATA3_PO4, ULPI, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(ULPI_DATA4_PO5, ULPI, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(ULPI_DATA5_PO6, ULPI, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(ULPI_DATA6_PO7, ULPI, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(DAP3_FS_PP0, I2S2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(DAP3_DIN_PP1, I2S2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(DAP3_DOUT_PP2, RSVD4, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(HDMI_INT_PN7, DEFAULT, DOWN, NORMAL, INPUT, DEFAULT, NORMAL), + PINCFG(ULPI_DATA7_PO0, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA0_PO1, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA1_PO2, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA2_PO3, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA3_PO4, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA4_PO5, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA5_PO6, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA6_PO7, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DAP3_FS_PP0, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(DAP3_DIN_PP1, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(DAP3_DOUT_PP2, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(DAP3_SCLK_PP3, RSVD3, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), PINCFG(DAP4_FS_PP4, I2S3, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(DAP4_DIN_PP5, I2S3, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(DAP4_DOUT_PP6, I2S3, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(DAP4_SCLK_PP7, I2S3, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(KB_COL0_PQ0, RSVD2, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(KB_COL1_PQ1, RSVD2, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(KB_COL2_PQ2, RSVD2, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL0_PQ0, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL1_PQ1, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL2_PQ2, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(KB_COL3_PQ3, KBC, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), PINCFG(KB_COL4_PQ4, SDMMC3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(KB_COL5_PQ5, RSVD2, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(KB_COL6_PQ6, RSVD2, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(KB_COL7_PQ7, RSVD2, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(KB_ROW0_PR0, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(KB_ROW1_PR1, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(KB_ROW2_PR2, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL5_PQ5, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL6_PQ6, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL7_PQ7, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW0_PR0, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW1_PR1, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW2_PR2, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(KB_ROW3_PR3, SYS, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(KB_ROW4_PR4, RSVD3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(KB_ROW5_PR5, RSVD3, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW4_PR4, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW5_PR5, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(KB_ROW6_PR6, DISPLAYA_ALT, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(KB_ROW7_PR7, RSVD2, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(KB_ROW8_PS0, RSVD2, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW7_PR7, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW8_PS0, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(KB_ROW9_PS1, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(KB_ROW10_PS2, RSVD2, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(KB_ROW11_PS3, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(KB_ROW12_PS4, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(KB_ROW13_PS5, RSVD2, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(KB_ROW14_PS6, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW11_PS3, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW12_PS4, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW13_PS5, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW14_PS6, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(KB_ROW15_PS7, SOC, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(KB_ROW16_PT0, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(KB_ROW17_PT1, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW16_PT0, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW17_PT1, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(GEN2_I2C_SCL_PT5, I2C2, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), PINCFG(GEN2_I2C_SDA_PT6, I2C2, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), PINCFG(SDMMC4_CMD_PT7, SDMMC4, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PU0, RSVD4, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PU1, RSVD1, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PU2, RSVD1, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PU3, GMI, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PU4, GMI, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PU5, GMI, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PU6, RSVD3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PV0, RSVD1, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PV1, RSVD1, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PU0, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PU1, DEFAULT, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PU2, DEFAULT, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PU3, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PU4, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PU5, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PU6, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PV0, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PV1, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(SDMMC3_CD_N_PV2, SDMMC3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(SDMMC1_WP_N_PV3, SDMMC1, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), PINCFG(DDC_SCL_PV4, I2C4, NORMAL, NORMAL, INPUT, DEFAULT, NORMAL), PINCFG(DDC_SDA_PV5, I2C4, NORMAL, NORMAL, INPUT, DEFAULT, NORMAL), - PINCFG(GPIO_W2_AUD_PW2, RSVD2, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(GPIO_W3_AUD_PW3, SPI6, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_W2_AUD_PW2, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_W3_AUD_PW3, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(DAP_MCLK1_PW4, EXTPERIPH1, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(CLK2_OUT_PW5, EXTPERIPH2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(UART3_TXD_PW6, UARTC, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(UART3_RXD_PW7, UARTC, UP, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(DVFS_PWM_PX0, CLDVFS, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(GPIO_X1_AUD_PX1, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_X1_AUD_PX1, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(DVFS_CLK_PX2, CLDVFS, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(GPIO_X3_AUD_PX3, RSVD4, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(GPIO_X4_AUD_PX4, GMI, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(GPIO_X5_AUD_PX5, RSVD4, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(GPIO_X6_AUD_PX6, GMI, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(GPIO_X7_AUD_PX7, RSVD1, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_X3_AUD_PX3, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_X4_AUD_PX4, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_X5_AUD_PX5, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_X6_AUD_PX6, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_X7_AUD_PX7, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(ULPI_CLK_PY0, SPI1, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(ULPI_DIR_PY1, SPI1, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(ULPI_NXT_PY2, SPI1, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), @@ -181,25 +273,25 @@ static const struct pmux_pingrp_config jetson_tk1_pingrps[] = { PINCFG(PBB0, VIMCLK2_ALT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(CAM_I2C_SCL_PBB1, I2C3, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), PINCFG(CAM_I2C_SDA_PBB2, I2C3, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), - PINCFG(PBB3, VGP3, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PBB3, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(PBB4, VGP4, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PBB5, RSVD3, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PBB6, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PBB7, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PBB5, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PBB6, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PBB7, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(CAM_MCLK_PCC0, VI_ALT3, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(PCC1, RSVD2, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(PCC2, RSVD2, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PCC1, DEFAULT, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PCC2, DEFAULT, DOWN, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(SDMMC4_CLK_PCC4, SDMMC4, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(CLK2_REQ_PCC5, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(CLK2_REQ_PCC5, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(CLK3_OUT_PEE0, EXTPERIPH3, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), - PINCFG(CLK3_REQ_PEE1, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(CLK3_REQ_PEE1, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(DAP_MCLK1_REQ_PEE2, SATA, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(HDMI_CEC_PEE3, CEC, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), PINCFG(SDMMC3_CLK_LB_OUT_PEE4, SDMMC3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(SDMMC3_CLK_LB_IN_PEE5, SDMMC3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), PINCFG(DP_HPD_PFF0, DP, UP, NORMAL, INPUT, DEFAULT, DEFAULT), - PINCFG(USB_VBUS_EN2_PFF1, RSVD2, NORMAL, NORMAL, OUTPUT, DISABLE, DEFAULT), - PINCFG(PFF2, RSVD2, UP, NORMAL, INPUT, DISABLE, DEFAULT), + PINCFG(USB_VBUS_EN2_PFF1, DEFAULT, NORMAL, NORMAL, OUTPUT, DISABLE, DEFAULT), + PINCFG(PFF2, DEFAULT, UP, NORMAL, INPUT, DISABLE, DEFAULT), PINCFG(CORE_PWR_REQ, PWRON, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(CPU_PWR_REQ, RSVD2, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), PINCFG(PWR_INT_N, PMI, UP, NORMAL, INPUT, DEFAULT, DEFAULT), diff --git a/board/nvidia/venice2/pinmux-config-venice2.h b/board/nvidia/venice2/pinmux-config-venice2.h index 2f79ec7523..bf8e3fd965 100644 --- a/board/nvidia/venice2/pinmux-config-venice2.h +++ b/board/nvidia/venice2/pinmux-config-venice2.h @@ -1,76 +1,286 @@ /* - * (C) Copyright 2013 - * NVIDIA Corporation <www.nvidia.com> + * Copyright (c) 2014, NVIDIA CORPORATION. All rights reserved. * - * SPDX-License-Identifier: GPL-2.0+ + * SPDX-License-Identifier: GPL-2.0+ */ #ifndef _PINMUX_CONFIG_VENICE2_H_ #define _PINMUX_CONFIG_VENICE2_H_ -#define DEFAULT_PINMUX(_pingrp, _mux, _pull, _tri, _io) \ - { \ - .pingrp = PMUX_PINGRP_##_pingrp, \ - .func = PMUX_FUNC_##_mux, \ - .pull = PMUX_PULL_##_pull, \ - .tristate = PMUX_TRI_##_tri, \ - .io = PMUX_PIN_##_io, \ - .lock = PMUX_PIN_LOCK_DEFAULT, \ - .od = PMUX_PIN_OD_DEFAULT, \ - .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \ +#define GPIO_INIT(_gpio, _init) \ + { \ + .gpio = GPIO_P##_gpio, \ + .init = TEGRA_GPIO_INIT_##_init, \ } -#define I2C_PINMUX(_pingrp, _mux, _pull, _tri, _io, _lock, _od) \ - { \ - .pingrp = PMUX_PINGRP_##_pingrp, \ - .func = PMUX_FUNC_##_mux, \ - .pull = PMUX_PULL_##_pull, \ - .tristate = PMUX_TRI_##_tri, \ - .io = PMUX_PIN_##_io, \ - .lock = PMUX_PIN_LOCK_##_lock, \ - .od = PMUX_PIN_OD_##_od, \ - .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \ - } +static const struct tegra_gpio_config venice2_gpio_inits[] = { + /* gpio, init_val */ + GPIO_INIT(A0, IN), + GPIO_INIT(C7, IN), + GPIO_INIT(G0, IN), + GPIO_INIT(G1, IN), + GPIO_INIT(G2, IN), + GPIO_INIT(G3, IN), + GPIO_INIT(H2, IN), + GPIO_INIT(H4, IN), + GPIO_INIT(H5, OUT0), + GPIO_INIT(H6, IN), + GPIO_INIT(H7, OUT1), + GPIO_INIT(I0, IN), + GPIO_INIT(I1, IN), + GPIO_INIT(I2, OUT0), + GPIO_INIT(I4, OUT0), + GPIO_INIT(I5, OUT1), + GPIO_INIT(I6, IN), + GPIO_INIT(J0, IN), + GPIO_INIT(J7, IN), + GPIO_INIT(K0, IN), + GPIO_INIT(K1, OUT0), + GPIO_INIT(K2, IN), + GPIO_INIT(K3, IN), + GPIO_INIT(K4, OUT0), + GPIO_INIT(K6, OUT0), + GPIO_INIT(K7, IN), + GPIO_INIT(N7, IN), + GPIO_INIT(O2, IN), + GPIO_INIT(O5, IN), + GPIO_INIT(O6, OUT0), + GPIO_INIT(O7, IN), + GPIO_INIT(P2, OUT0), + GPIO_INIT(Q0, IN), + GPIO_INIT(Q2, IN), + GPIO_INIT(Q3, IN), + GPIO_INIT(Q6, IN), + GPIO_INIT(Q7, IN), + GPIO_INIT(R0, OUT0), + GPIO_INIT(R1, IN), + GPIO_INIT(R4, IN), + GPIO_INIT(S0, IN), + GPIO_INIT(S3, OUT0), + GPIO_INIT(S4, OUT0), + GPIO_INIT(S7, IN), + GPIO_INIT(T1, IN), + GPIO_INIT(U4, IN), + GPIO_INIT(U5, IN), + GPIO_INIT(U6, IN), + GPIO_INIT(V0, IN), + GPIO_INIT(V1, IN), + GPIO_INIT(W3, IN), + GPIO_INIT(X1, IN), + GPIO_INIT(X3, IN), + GPIO_INIT(X4, IN), + GPIO_INIT(X7, OUT0), + GPIO_INIT(CC5, OUT0), +}; -#define DDC_PINMUX(_pingrp, _mux, _pull, _tri, _io, _lock, _rcv_sel) \ +#define PINCFG(_pingrp, _mux, _pull, _tri, _io, _od, _rcv_sel) \ { \ .pingrp = PMUX_PINGRP_##_pingrp, \ .func = PMUX_FUNC_##_mux, \ .pull = PMUX_PULL_##_pull, \ .tristate = PMUX_TRI_##_tri, \ .io = PMUX_PIN_##_io, \ - .lock = PMUX_PIN_LOCK_##_lock, \ + .od = PMUX_PIN_OD_##_od, \ .rcv_sel = PMUX_PIN_RCV_SEL_##_rcv_sel, \ + .lock = PMUX_PIN_LOCK_DEFAULT, \ .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \ } -#define VI_PINMUX(_pingrp, _mux, _pull, _tri, _io, _lock, _ioreset) \ - { \ - .pingrp = PMUX_PINGRP_##_pingrp, \ - .func = PMUX_FUNC_##_mux, \ - .pull = PMUX_PULL_##_pull, \ - .tristate = PMUX_TRI_##_tri, \ - .io = PMUX_PIN_##_io, \ - .lock = PMUX_PIN_LOCK_##_lock, \ - .od = PMUX_PIN_OD_DEFAULT, \ - .ioreset = PMUX_PIN_IO_RESET_##_ioreset \ - } - -#define CEC_PINMUX(_pingrp, _mux, _pull, _tri, _io, _lock, _od) \ - { \ - .pingrp = PMUX_PINGRP_##_pingrp, \ - .func = PMUX_FUNC_##_mux, \ - .pull = PMUX_PULL_##_pull, \ - .tristate = PMUX_TRI_##_tri, \ - .io = PMUX_PIN_##_io, \ - .lock = PMUX_PIN_LOCK_##_lock, \ - .od = PMUX_PIN_OD_##_od, \ - .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \ - } - -#define USB_PINMUX CEC_PINMUX +static const struct pmux_pingrp_config venice2_pingrps[] = { + /* pingrp, mux, pull, tri, e_input, od, rcv_sel */ + PINCFG(CLK_32K_OUT_PA0, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(UART3_CTS_N_PA1, UARTC, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DAP2_FS_PA2, I2S1, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DAP2_SCLK_PA3, I2S1, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DAP2_DIN_PA4, I2S1, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DAP2_DOUT_PA5, I2S1, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC3_CLK_PA6, SDMMC3, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC3_CMD_PA7, SDMMC3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PB0, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PB1, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC3_DAT3_PB4, SDMMC3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC3_DAT2_PB5, SDMMC3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC3_DAT1_PB6, SDMMC3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC3_DAT0_PB7, SDMMC3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(UART3_RTS_N_PC0, UARTC, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(UART2_TXD_PC2, IRDA, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(UART2_RXD_PC3, IRDA, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(GEN1_I2C_SCL_PC4, I2C1, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), + PINCFG(GEN1_I2C_SDA_PC5, I2C1, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), + PINCFG(PC7, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PG0, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PG1, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PG2, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PG3, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PG4, SPI4, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PG5, SPI4, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PG6, SPI4, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PG7, SPI4, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PH0, PWM0, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PH1, PWM1, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PH2, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PH3, GMI, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PH4, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PH5, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PH6, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PH7, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PI0, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PI1, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PI2, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PI3, SPI4, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PI4, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PI5, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PI6, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PI7, RSVD1, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PJ0, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PJ2, RSVD1, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(UART2_CTS_N_PJ5, UARTB, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(UART2_RTS_N_PJ6, UARTB, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PJ7, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PK0, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PK1, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PK2, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PK3, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PK4, DEFAULT, UP, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(SPDIF_OUT_PK5, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(SPDIF_IN_PK6, DEFAULT, DOWN, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PK7, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DAP1_FS_PN0, I2S0, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DAP1_DIN_PN1, I2S0, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DAP1_DOUT_PN2, I2S0, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DAP1_SCLK_PN3, I2S0, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(USB_VBUS_EN0_PN4, USB, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), + PINCFG(USB_VBUS_EN1_PN5, USB, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), + PINCFG(HDMI_INT_PN7, DEFAULT, DOWN, NORMAL, INPUT, DEFAULT, NORMAL), + PINCFG(ULPI_DATA7_PO0, ULPI, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA0_PO1, ULPI, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA1_PO2, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA2_PO3, ULPI, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA3_PO4, ULPI, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA4_PO5, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA5_PO6, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DATA6_PO7, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DAP3_FS_PP0, I2S2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(DAP3_DIN_PP1, I2S2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(DAP3_DOUT_PP2, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(DAP3_SCLK_PP3, RSVD3, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(DAP4_FS_PP4, I2S3, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(DAP4_DIN_PP5, I2S3, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DAP4_DOUT_PP6, I2S3, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(DAP4_SCLK_PP7, I2S3, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL0_PQ0, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL1_PQ1, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL2_PQ2, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL3_PQ3, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL4_PQ4, SDMMC3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL5_PQ5, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL6_PQ6, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_COL7_PQ7, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW0_PR0, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW1_PR1, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW2_PR2, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW3_PR3, KBC, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW4_PR4, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW5_PR5, RSVD3, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW6_PR6, KBC, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW7_PR7, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW8_PS0, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW9_PS1, UARTA, DOWN, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW10_PS2, UARTA, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW11_PS3, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW12_PS4, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW13_PS5, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW14_PS6, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW15_PS7, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW16_PT0, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(KB_ROW17_PT1, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(GEN2_I2C_SCL_PT5, I2C2, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), + PINCFG(GEN2_I2C_SDA_PT6, I2C2, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), + PINCFG(SDMMC4_CMD_PT7, SDMMC4, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PU0, UARTA, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PU1, UARTA, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PU2, UARTA, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PU3, UARTA, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PU4, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PU5, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PU6, DEFAULT, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PV0, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PV1, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC3_CD_N_PV2, SDMMC3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC1_WP_N_PV3, SDMMC1, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(DDC_SCL_PV4, I2C4, NORMAL, NORMAL, INPUT, DEFAULT, NORMAL), + PINCFG(DDC_SDA_PV5, I2C4, NORMAL, NORMAL, INPUT, DEFAULT, NORMAL), + PINCFG(GPIO_W2_AUD_PW2, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_W3_AUD_PW3, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DAP_MCLK1_PW4, EXTPERIPH1, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(CLK2_OUT_PW5, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(UART3_TXD_PW6, UARTC, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(UART3_RXD_PW7, UARTC, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DVFS_PWM_PX0, CLDVFS, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_X1_AUD_PX1, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DVFS_CLK_PX2, CLDVFS, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_X3_AUD_PX3, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_X4_AUD_PX4, DEFAULT, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_X5_AUD_PX5, RSVD4, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_X6_AUD_PX6, GMI, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(GPIO_X7_AUD_PX7, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_CLK_PY0, SPI1, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_DIR_PY1, SPI1, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_NXT_PY2, SPI1, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(ULPI_STP_PY3, SPI1, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC1_DAT3_PY4, SDMMC1, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC1_DAT2_PY5, SDMMC1, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC1_DAT1_PY6, SDMMC1, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC1_DAT0_PY7, SDMMC1, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC1_CLK_PZ0, SDMMC1, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC1_CMD_PZ1, SDMMC1, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PWR_I2C_SCL_PZ6, I2CPWR, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), + PINCFG(PWR_I2C_SDA_PZ7, I2CPWR, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), + PINCFG(SDMMC4_DAT0_PAA0, SDMMC4, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC4_DAT1_PAA1, SDMMC4, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC4_DAT2_PAA2, SDMMC4, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC4_DAT3_PAA3, SDMMC4, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC4_DAT4_PAA4, SDMMC4, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC4_DAT5_PAA5, SDMMC4, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC4_DAT6_PAA6, SDMMC4, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC4_DAT7_PAA7, SDMMC4, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(PBB0, VGP6, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(CAM_I2C_SCL_PBB1, I2C3, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), + PINCFG(CAM_I2C_SDA_PBB2, I2C3, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), + PINCFG(PBB3, VGP3, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PBB4, VGP4, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PBB5, RSVD3, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PBB6, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PBB7, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(CAM_MCLK_PCC0, VI, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PCC1, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PCC2, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC4_CLK_PCC4, SDMMC4, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(CLK2_REQ_PCC5, DEFAULT, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PEX_L0_RST_N_PDD1, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PEX_L0_CLKREQ_N_PDD2, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PEX_WAKE_N_PDD3, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PEX_L1_RST_N_PDD5, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PEX_L1_CLKREQ_N_PDD6, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(CLK3_OUT_PEE0, EXTPERIPH3, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(CLK3_REQ_PEE1, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(DAP_MCLK1_REQ_PEE2, RSVD4, DOWN, TRISTATE, OUTPUT, DEFAULT, DEFAULT), + PINCFG(HDMI_CEC_PEE3, CEC, NORMAL, NORMAL, INPUT, ENABLE, DEFAULT), + PINCFG(SDMMC3_CLK_LB_OUT_PEE4, SDMMC3, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(SDMMC3_CLK_LB_IN_PEE5, SDMMC3, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(DP_HPD_PFF0, DP, UP, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(USB_VBUS_EN2_PFF1, RSVD2, DOWN, TRISTATE, OUTPUT, DISABLE, DEFAULT), + PINCFG(PFF2, RSVD2, DOWN, TRISTATE, OUTPUT, DISABLE, DEFAULT), + PINCFG(CORE_PWR_REQ, PWRON, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(CPU_PWR_REQ, CPU, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(PWR_INT_N, PMI, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(RESET_OUT_N, RESET_OUT_N, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), + PINCFG(OWR, RSVD2, DOWN, TRISTATE, OUTPUT, DEFAULT, NORMAL), + PINCFG(CLK_32K_IN, CLK, NORMAL, NORMAL, INPUT, DEFAULT, DEFAULT), + PINCFG(JTAG_RTCK, RTCK, NORMAL, NORMAL, OUTPUT, DEFAULT, DEFAULT), +}; -#define DEFAULT_PADCFG(_drvgrp, _slwf, _slwr, _drvup, _drvdn, _lpmd, _schmt, _hsm) \ +#define DRVCFG(_drvgrp, _slwf, _slwr, _drvup, _drvdn, _lpmd, _schmt, _hsm) \ { \ .drvgrp = PMUX_DRVGRP_##_drvgrp, \ .slwf = _slwf, \ @@ -82,258 +292,7 @@ .hsm = PMUX_HSM_##_hsm, \ } -static struct pmux_pingrp_config tegra124_pinmux_common[] = { - /* EXTPERIPH1 pinmux */ - DEFAULT_PINMUX(DAP_MCLK1_PW4, EXTPERIPH1, NORMAL, NORMAL, OUTPUT), - - /* I2S0 pinmux */ - DEFAULT_PINMUX(DAP1_DIN_PN1, I2S0, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(DAP1_DOUT_PN2, I2S0, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(DAP1_FS_PN0, I2S0, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(DAP1_SCLK_PN3, I2S0, NORMAL, NORMAL, INPUT), - - /* I2S1 pinmux */ - DEFAULT_PINMUX(DAP2_DIN_PA4, I2S1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(DAP2_DOUT_PA5, I2S1, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(DAP2_FS_PA2, I2S1, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(DAP2_SCLK_PA3, I2S1, NORMAL, NORMAL, INPUT), - - /* I2S3 pinmux */ - DEFAULT_PINMUX(DAP4_DIN_PP5, I2S3, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(DAP4_DOUT_PP6, I2S3, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(DAP4_FS_PP4, I2S3, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(DAP4_SCLK_PP7, I2S3, NORMAL, NORMAL, INPUT), - - /* CLDVFS pinmux */ - DEFAULT_PINMUX(DVFS_PWM_PX0, CLDVFS, NORMAL, NORMAL, OUTPUT), - DEFAULT_PINMUX(DVFS_CLK_PX2, CLDVFS, NORMAL, NORMAL, OUTPUT), - - /* ULPI pinmux */ - DEFAULT_PINMUX(ULPI_DATA0_PO1, ULPI, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(ULPI_DATA1_PO2, ULPI, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(ULPI_DATA2_PO3, ULPI, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(ULPI_DATA3_PO4, ULPI, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(ULPI_DATA4_PO5, ULPI, UP, NORMAL, INPUT), - DEFAULT_PINMUX(ULPI_DATA5_PO6, ULPI, UP, NORMAL, INPUT), - DEFAULT_PINMUX(ULPI_DATA6_PO7, ULPI, NORMAL, NORMAL, INPUT), - - /* EC KBC/SPI */ - DEFAULT_PINMUX(ULPI_CLK_PY0, SPI1, UP, NORMAL, INPUT), - DEFAULT_PINMUX(ULPI_DIR_PY1, SPI1, UP, NORMAL, INPUT), - DEFAULT_PINMUX(ULPI_NXT_PY2, SPI1, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(ULPI_STP_PY3, SPI1, NORMAL, NORMAL, INPUT), - - /* I2C3 (TPM) pinmux */ - I2C_PINMUX(CAM_I2C_SCL_PBB1, I2C3, NORMAL, NORMAL, INPUT, DEFAULT, ENABLE), - I2C_PINMUX(CAM_I2C_SDA_PBB2, I2C3, NORMAL, NORMAL, INPUT, DEFAULT, ENABLE), - - /* I2C2 pinmux */ - I2C_PINMUX(GEN2_I2C_SCL_PT5, I2C2, NORMAL, NORMAL, INPUT, DEFAULT, ENABLE), - I2C_PINMUX(GEN2_I2C_SDA_PT6, I2C2, NORMAL, NORMAL, INPUT, DEFAULT, ENABLE), - - /* UARTD pinmux (UART4 on Servo board, unused) */ - DEFAULT_PINMUX(PJ7, UARTD, NORMAL, NORMAL, OUTPUT), - DEFAULT_PINMUX(PB0, UARTD, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(PB1, UARTD, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(PK7, UARTD, NORMAL, NORMAL, OUTPUT), - - /* SPI4 (Winbond 'boot ROM') */ - DEFAULT_PINMUX(PG5, SPI4, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(PG6, SPI4, UP, NORMAL, INPUT), - DEFAULT_PINMUX(PG7, SPI4, UP, NORMAL, INPUT), - DEFAULT_PINMUX(PI3, SPI4, NORMAL, NORMAL, INPUT), - - /* Touch IRQ */ - DEFAULT_PINMUX(GPIO_W3_AUD_PW3, RSVD1, NORMAL, NORMAL, INPUT), - - /* PWM1 pinmux */ - DEFAULT_PINMUX(PH1, PWM1, NORMAL, NORMAL, OUTPUT), - - /* SDMMC1 pinmux */ - DEFAULT_PINMUX(SDMMC1_CLK_PZ0, SDMMC1, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC1_CMD_PZ1, SDMMC1, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC1_DAT0_PY7, SDMMC1, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC1_DAT1_PY6, SDMMC1, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC1_DAT2_PY5, SDMMC1, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC1_DAT3_PY4, SDMMC1, UP, NORMAL, INPUT), - - /* SDMMC3 pinmux */ - DEFAULT_PINMUX(SDMMC3_CLK_PA6, SDMMC3, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC3_CMD_PA7, SDMMC3, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC3_DAT0_PB7, SDMMC3, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC3_DAT1_PB6, SDMMC3, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC3_DAT2_PB5, SDMMC3, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC3_DAT3_PB4, SDMMC3, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC3_CLK_LB_IN_PEE5, SDMMC3, UP, TRISTATE, INPUT), - DEFAULT_PINMUX(SDMMC3_CLK_LB_OUT_PEE4, SDMMC3, DOWN, NORMAL, INPUT), - - /* SDMMC4 pinmux */ - DEFAULT_PINMUX(SDMMC4_CLK_PCC4, SDMMC4, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC4_CMD_PT7, SDMMC4, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC4_DAT0_PAA0, SDMMC4, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC4_DAT1_PAA1, SDMMC4, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC4_DAT2_PAA2, SDMMC4, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC4_DAT3_PAA3, SDMMC4, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC4_DAT4_PAA4, SDMMC4, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC4_DAT5_PAA5, SDMMC4, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC4_DAT6_PAA6, SDMMC4, UP, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC4_DAT7_PAA7, SDMMC4, UP, NORMAL, INPUT), - - /* BLINK pinmux */ - DEFAULT_PINMUX(CLK_32K_OUT_PA0, BLINK, NORMAL, NORMAL, OUTPUT), - - /* KBC pinmux */ - DEFAULT_PINMUX(KB_COL0_PQ0, KBC, UP, NORMAL, INPUT), - DEFAULT_PINMUX(KB_COL1_PQ1, KBC, UP, NORMAL, INPUT), - DEFAULT_PINMUX(KB_COL2_PQ2, KBC, UP, NORMAL, INPUT), - DEFAULT_PINMUX(KB_ROW0_PR0, KBC, UP, NORMAL, INPUT), - DEFAULT_PINMUX(KB_ROW1_PR1, KBC, UP, NORMAL, INPUT), - - /* Misc */ - DEFAULT_PINMUX(PV0, RSVD1, NORMAL, TRISTATE, OUTPUT), - DEFAULT_PINMUX(KB_ROW7_PR7, RSVD1, UP, NORMAL, INPUT), - - /* UARTA pinmux (BR_UART_TXD/RXD on Servo board) */ - DEFAULT_PINMUX(KB_ROW9_PS1, UARTA, UP, NORMAL, OUTPUT), - DEFAULT_PINMUX(KB_ROW10_PS2, UARTA, UP, TRISTATE, INPUT), - - /* I2CPWR pinmux (I2C5) */ - I2C_PINMUX(PWR_I2C_SCL_PZ6, I2CPWR, NORMAL, NORMAL, INPUT, DEFAULT, ENABLE), - I2C_PINMUX(PWR_I2C_SDA_PZ7, I2CPWR, NORMAL, NORMAL, INPUT, DEFAULT, ENABLE), - - /* RTCK pinmux */ - DEFAULT_PINMUX(JTAG_RTCK, RTCK, NORMAL, NORMAL, INPUT), - - /* CLK pinmux */ - DEFAULT_PINMUX(CLK_32K_IN, CLK, NORMAL, TRISTATE, INPUT), - - /* PWRON pinmux */ - DEFAULT_PINMUX(CORE_PWR_REQ, PWRON, NORMAL, NORMAL, OUTPUT), - - /* CPU pinmux */ - DEFAULT_PINMUX(CPU_PWR_REQ, CPU, NORMAL, NORMAL, OUTPUT), - - /* PMI pinmux */ - DEFAULT_PINMUX(PWR_INT_N, PMI, NORMAL, TRISTATE, INPUT), - - /* RESET_OUT_N pinmux */ - DEFAULT_PINMUX(RESET_OUT_N, RESET_OUT_N, NORMAL, NORMAL, OUTPUT), - - /* EXTPERIPH3 pinmux */ - DEFAULT_PINMUX(CLK3_OUT_PEE0, EXTPERIPH3, NORMAL, NORMAL, OUTPUT), - - /* I2C1 pinmux */ - I2C_PINMUX(GEN1_I2C_SCL_PC4, I2C1, NORMAL, NORMAL, INPUT, DEFAULT, ENABLE), - I2C_PINMUX(GEN1_I2C_SDA_PC5, I2C1, NORMAL, NORMAL, INPUT, DEFAULT, ENABLE), - - /* UARTB, GPS */ - DEFAULT_PINMUX(UART2_CTS_N_PJ5, UARTB, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(UART2_RTS_N_PJ6, UARTB, NORMAL, NORMAL, OUTPUT), - DEFAULT_PINMUX(UART2_RXD_PC3, IRDA, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(UART2_TXD_PC2, IRDA, NORMAL, NORMAL, OUTPUT), - - /* UARTC (WIFI/BT) */ - DEFAULT_PINMUX(UART3_CTS_N_PA1, UARTC, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(UART3_RTS_N_PC0, UARTC, NORMAL, NORMAL, OUTPUT), - DEFAULT_PINMUX(UART3_RXD_PW7, UARTC, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(UART3_TXD_PW6, UARTC, NORMAL, NORMAL, OUTPUT), - - /* CEC pinmux */ - CEC_PINMUX(HDMI_CEC_PEE3, CEC, NORMAL, NORMAL, INPUT, DEFAULT, DISABLE), - - /* I2C4 (HDMI_DDC) pinmux */ - DDC_PINMUX(DDC_SCL_PV4, I2C4, NORMAL, NORMAL, INPUT, DEFAULT, HIGH), - DDC_PINMUX(DDC_SDA_PV5, I2C4, NORMAL, NORMAL, INPUT, DEFAULT, HIGH), - - /* USB pinmux */ - USB_PINMUX(USB_VBUS_EN0_PN4, USB, NORMAL, NORMAL, INPUT, DEFAULT, ENABLE), - USB_PINMUX(USB_VBUS_EN1_PN5, USB, NORMAL, NORMAL, INPUT, DEFAULT, ENABLE), - - /* Unused, marked SNN_ on schematic, TRISTATE 'em */ - DEFAULT_PINMUX(PBB0, RSVD3, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(PBB3, RSVD3, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(PBB4, RSVD3, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(PBB5, RSVD2, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(PBB6, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(PBB7, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(PCC1, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(PCC2, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(PH3, GMI, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(PI7, GMI, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(PJ2, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(GPIO_X5_AUD_PX5, RSVD3, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(GPIO_X6_AUD_PX6, GMI, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(GPIO_W2_AUD_PW2, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(PFF2, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(USB_VBUS_EN2_PFF1, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(KB_COL5_PQ5, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(KB_ROW2_PR2, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(KB_ROW3_PR3, KBC, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(KB_ROW5_PR5, RSVD2, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(KB_ROW6_PR6, KBC, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(KB_ROW13_PS5, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(KB_ROW14_PS6, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(KB_ROW16_PT0, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(OWR, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(ULPI_DATA7_PO0, ULPI, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(DAP3_DIN_PP1, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(DAP3_FS_PP0, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(DAP3_SCLK_PP3, RSVD2, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(CLK2_OUT_PW5, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(SDMMC1_WP_N_PV3, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(CAM_MCLK_PCC0, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(CLK3_REQ_PEE1, RSVD1, NORMAL, TRISTATE, INPUT), - DEFAULT_PINMUX(SPDIF_OUT_PK5, RSVD1, NORMAL, TRISTATE, INPUT), -}; - -static struct pmux_pingrp_config unused_pins_lowpower[] = { - DEFAULT_PINMUX(DAP_MCLK1_REQ_PEE2, RSVD3, DOWN, TRISTATE, OUTPUT), -}; - -/* Initially setting all used GPIO's to non-TRISTATE */ -static struct pmux_pingrp_config tegra124_pinmux_set_nontristate[] = { - DEFAULT_PINMUX(GPIO_X4_AUD_PX4, RSVD1, DOWN, NORMAL, OUTPUT), - DEFAULT_PINMUX(GPIO_X7_AUD_PX7, RSVD1, DOWN, NORMAL, OUTPUT), - DEFAULT_PINMUX(GPIO_W2_AUD_PW2, RSVD1, UP, NORMAL, INPUT), - DEFAULT_PINMUX(GPIO_X3_AUD_PX3, RSVD3, UP, NORMAL, INPUT), - - /* EN_VDD_BL */ - DEFAULT_PINMUX(DAP3_DOUT_PP2, I2S2, DOWN, NORMAL, OUTPUT), - - /* MODEM */ - DEFAULT_PINMUX(PV0, RSVD3, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(PV1, RSVD1, NORMAL, NORMAL, INPUT), - - /* BOOT_SEL0-3 */ - DEFAULT_PINMUX(PG0, GMI, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(PG1, GMI, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(PG2, GMI, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(PG3, GMI, NORMAL, NORMAL, INPUT), - - DEFAULT_PINMUX(CLK2_REQ_PCC5, RSVD3, NORMAL, NORMAL, OUTPUT), - - DEFAULT_PINMUX(KB_COL3_PQ3, KBC, UP, NORMAL, OUTPUT), - DEFAULT_PINMUX(KB_COL4_PQ4, SDMMC3, UP, NORMAL, INPUT), - DEFAULT_PINMUX(KB_COL6_PQ6, KBC, UP, NORMAL, OUTPUT), - DEFAULT_PINMUX(KB_COL7_PQ7, KBC, UP, NORMAL, OUTPUT), - DEFAULT_PINMUX(KB_ROW4_PR4, KBC, DOWN, NORMAL, INPUT), - DEFAULT_PINMUX(KB_ROW8_PS0, KBC, UP, NORMAL, INPUT), - - DEFAULT_PINMUX(PU4, RSVD3, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(PU5, RSVD3, NORMAL, NORMAL, OUTPUT), - DEFAULT_PINMUX(PU6, RSVD3, NORMAL, NORMAL, INPUT), - - DEFAULT_PINMUX(HDMI_INT_PN7, RSVD1, DOWN, NORMAL, INPUT), - DEFAULT_PINMUX(SPDIF_IN_PK6, RSVD2, NORMAL, NORMAL, INPUT), - DEFAULT_PINMUX(SDMMC3_CD_N_PV2, SDMMC3, UP, NORMAL, INPUT), - - /* TS_SHDN_L */ - DEFAULT_PINMUX(PK1, GMI, NORMAL, NORMAL, OUTPUT), +static const struct pmux_drvgrp_config venice2_drvgrps[] = { }; -static struct pmux_drvgrp_config venice2_padctrl[] = { - /* (_drvgrp, _slwf, _slwr, _drvup, _drvdn, _lpmd, _schmt, _hsm) */ - DEFAULT_PADCFG(SDIO3, SDIOCFG_DRVUP_SLWF, SDIOCFG_DRVDN_SLWR, - SDIOCFG_DRVUP, SDIOCFG_DRVDN, NONE, NONE, NONE), -}; #endif /* PINMUX_CONFIG_VENICE2_H */ diff --git a/board/nvidia/venice2/venice2.c b/board/nvidia/venice2/venice2.c index 15082c4195..c56ef129d6 100644 --- a/board/nvidia/venice2/venice2.c +++ b/board/nvidia/venice2/venice2.c @@ -6,12 +6,9 @@ */ #include <common.h> -#include <asm-generic/gpio.h> #include <asm/arch/gpio.h> -#include <asm/arch/gp_padctrl.h> #include <asm/arch/pinmux.h> #include "pinmux-config-venice2.h" -#include <i2c.h> /* * Routine: pinmux_init @@ -19,16 +16,14 @@ */ void pinmux_init(void) { - pinmux_config_pingrp_table(tegra124_pinmux_set_nontristate, - ARRAY_SIZE(tegra124_pinmux_set_nontristate)); + pinmux_set_tristate_input_clamping(); - pinmux_config_pingrp_table(tegra124_pinmux_common, - ARRAY_SIZE(tegra124_pinmux_common)); + gpio_config_table(venice2_gpio_inits, + ARRAY_SIZE(venice2_gpio_inits)); - pinmux_config_pingrp_table(unused_pins_lowpower, - ARRAY_SIZE(unused_pins_lowpower)); + pinmux_config_pingrp_table(venice2_pingrps, + ARRAY_SIZE(venice2_pingrps)); - /* Initialize any non-default pad configs (APB_MISC_GP regs) */ - pinmux_config_drvgrp_table(venice2_padctrl, - ARRAY_SIZE(venice2_padctrl)); + pinmux_config_drvgrp_table(venice2_drvgrps, + ARRAY_SIZE(venice2_drvgrps)); } diff --git a/board/renesas/koelsch/koelsch.c b/board/renesas/koelsch/koelsch.c index 32d3b584bc..bfd0cc6884 100644 --- a/board/renesas/koelsch/koelsch.c +++ b/board/renesas/koelsch/koelsch.c @@ -19,186 +19,28 @@ #include <netdev.h> #include <miiphy.h> #include <i2c.h> +#include <div64.h> #include "qos.h" DECLARE_GLOBAL_DATA_PTR; -#define s_init_wait(cnt) \ - ({ \ - u32 i = 0x10000 * cnt; \ - while (i > 0) \ - i--; \ - }) - - -#define dbpdrgd_check(bsc) \ - ({ \ - while ((readl(&bsc->dbpdrgd) & 0x1) != 0x1) \ - ; \ - }) - -#if defined(CONFIG_NORFLASH) -static void bsc_init(void) -{ - struct r8a7791_lbsc *lbsc = (struct r8a7791_lbsc *)LBSC_BASE; - struct r8a7791_dbsc3 *dbsc3_0 = (struct r8a7791_dbsc3 *)DBSC3_0_BASE; - - /* LBSC */ - writel(0x00000020, &lbsc->cs0ctrl); - writel(0x00000020, &lbsc->cs1ctrl); - writel(0x00002020, &lbsc->ecs0ctrl); - writel(0x00002020, &lbsc->ecs1ctrl); - - writel(0x077F077F, &lbsc->cswcr0); - writel(0x077F077F, &lbsc->cswcr1); - writel(0x077F077F, &lbsc->ecswcr0); - writel(0x077F077F, &lbsc->ecswcr1); - - /* DBSC3 */ - s_init_wait(10); - - writel(0x0000A55A, &dbsc3_0->dbpdlck); - writel(0x00000001, &dbsc3_0->dbpdrga); - writel(0x80000000, &dbsc3_0->dbpdrgd); - writel(0x00000004, &dbsc3_0->dbpdrga); - dbpdrgd_check(dbsc3_0); - - writel(0x00000006, &dbsc3_0->dbpdrga); - writel(0x0001C000, &dbsc3_0->dbpdrgd); - - writel(0x00000023, &dbsc3_0->dbpdrga); - writel(0x00FD2480, &dbsc3_0->dbpdrgd); - - writel(0x00000010, &dbsc3_0->dbpdrga); - writel(0xF004649B, &dbsc3_0->dbpdrgd); - - writel(0x0000000F, &dbsc3_0->dbpdrga); - writel(0x00181EE4, &dbsc3_0->dbpdrgd); - - writel(0x0000000E, &dbsc3_0->dbpdrga); - writel(0x33C03812, &dbsc3_0->dbpdrgd); - - writel(0x00000003, &dbsc3_0->dbpdrga); - writel(0x0300C481, &dbsc3_0->dbpdrgd); - - writel(0x00000007, &dbsc3_0->dbkind); - writel(0x10030A02, &dbsc3_0->dbconf0); - writel(0x00000001, &dbsc3_0->dbphytype); - writel(0x00000000, &dbsc3_0->dbbl); - writel(0x0000000B, &dbsc3_0->dbtr0); - writel(0x00000008, &dbsc3_0->dbtr1); - writel(0x00000000, &dbsc3_0->dbtr2); - writel(0x0000000B, &dbsc3_0->dbtr3); - writel(0x000C000B, &dbsc3_0->dbtr4); - writel(0x00000027, &dbsc3_0->dbtr5); - writel(0x0000001C, &dbsc3_0->dbtr6); - writel(0x00000005, &dbsc3_0->dbtr7); - writel(0x00000018, &dbsc3_0->dbtr8); - writel(0x00000008, &dbsc3_0->dbtr9); - writel(0x0000000C, &dbsc3_0->dbtr10); - writel(0x00000009, &dbsc3_0->dbtr11); - writel(0x00000012, &dbsc3_0->dbtr12); - writel(0x000000D0, &dbsc3_0->dbtr13); - writel(0x00140005, &dbsc3_0->dbtr14); - writel(0x00050004, &dbsc3_0->dbtr15); - writel(0x70233005, &dbsc3_0->dbtr16); - writel(0x000C0000, &dbsc3_0->dbtr17); - writel(0x00000300, &dbsc3_0->dbtr18); - writel(0x00000040, &dbsc3_0->dbtr19); - writel(0x00000001, &dbsc3_0->dbrnk0); - writel(0x00020001, &dbsc3_0->dbadj0); - writel(0x20082008, &dbsc3_0->dbadj2); - writel(0x00020002, &dbsc3_0->dbwt0cnf0); - writel(0x0000000F, &dbsc3_0->dbwt0cnf4); - - writel(0x00000015, &dbsc3_0->dbpdrga); - writel(0x00000D70, &dbsc3_0->dbpdrgd); - - writel(0x00000016, &dbsc3_0->dbpdrga); - writel(0x00000006, &dbsc3_0->dbpdrgd); - - writel(0x00000017, &dbsc3_0->dbpdrga); - writel(0x00000018, &dbsc3_0->dbpdrgd); - - writel(0x00000012, &dbsc3_0->dbpdrga); - writel(0x9D5CBB66, &dbsc3_0->dbpdrgd); - - writel(0x00000013, &dbsc3_0->dbpdrga); - writel(0x1A868300, &dbsc3_0->dbpdrgd); - - writel(0x00000023, &dbsc3_0->dbpdrga); - writel(0x00FDB6C0, &dbsc3_0->dbpdrgd); - - writel(0x00000014, &dbsc3_0->dbpdrga); - writel(0x300214D8, &dbsc3_0->dbpdrgd); - - writel(0x0000001A, &dbsc3_0->dbpdrga); - writel(0x930035C7, &dbsc3_0->dbpdrgd); - - writel(0x00000060, &dbsc3_0->dbpdrga); - writel(0x330657B2, &dbsc3_0->dbpdrgd); - - writel(0x00000011, &dbsc3_0->dbpdrga); - writel(0x1000040B, &dbsc3_0->dbpdrgd); - - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x00000001, &dbsc3_0->dbpdrga); - writel(0x00000071, &dbsc3_0->dbpdrgd); - - writel(0x00000004, &dbsc3_0->dbpdrga); - dbpdrgd_check(dbsc3_0); - - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x2100FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - - writel(0x110000DB, &dbsc3_0->dbcmd); - - writel(0x00000001, &dbsc3_0->dbpdrga); - writel(0x00000181, &dbsc3_0->dbpdrgd); - - writel(0x00000004, &dbsc3_0->dbpdrga); - dbpdrgd_check(dbsc3_0); - - writel(0x00000001, &dbsc3_0->dbpdrga); - writel(0x0000FE01, &dbsc3_0->dbpdrgd); - - writel(0x00000004, &dbsc3_0->dbpdrga); - dbpdrgd_check(dbsc3_0); - - writel(0x00000000, &dbsc3_0->dbbs0cnt1); - writel(0x01004C20, &dbsc3_0->dbcalcnf); - writel(0x014000AA, &dbsc3_0->dbcaltr); - writel(0x00000140, &dbsc3_0->dbrfcnf0); - writel(0x00081860, &dbsc3_0->dbrfcnf1); - writel(0x00010000, &dbsc3_0->dbrfcnf2); - writel(0x00000001, &dbsc3_0->dbrfen); - writel(0x00000001, &dbsc3_0->dbacen); -} -#else -#define bsc_init() do {} while (0) -#endif /* CONFIG_NORFLASH */ - +#define CLK2MHZ(clk) (clk / 1000 / 1000) void s_init(void) { - struct r8a7791_rwdt *rwdt = (struct r8a7791_rwdt *)RWDT_BASE; - struct r8a7791_swdt *swdt = (struct r8a7791_swdt *)SWDT_BASE; + struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE; + struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE; + u32 stc; /* Watchdog init */ writel(0xA5A5A500, &rwdt->rwtcsra); writel(0xA5A5A500, &swdt->swtcsra); + /* CPU frequency setting. Set to 1.5GHz */ + stc = ((1500 / CLK2MHZ(CONFIG_SYS_CLK_FREQ)) - 1) << PLL0_STC_BIT; + clrsetbits_le32(PLL0CR, PLL0_STC_MASK, stc); + /* QoS */ qos_init(); - - /* BSC */ - bsc_init(); } #define MSTPSR1 0xE6150038 @@ -213,18 +55,6 @@ void s_init(void) #define SMSTPCR8 0xE6150990 #define ETHER_MSTP813 (1 << 13) -#define PMMR 0xE6060000 -#define GPSR4 0xE6060014 -#define IPSR14 0xE6060058 - -#define set_guard_reg(addr, mask, value) \ -{ \ - u32 val; \ - val = (readl(addr) & ~(mask)) | (value); \ - writel(~val, PMMR); \ - writel(val, addr); \ -} - #define mstp_setbits(type, addr, saddr, set) \ out_##type((saddr), in_##type(addr) | (set)) #define mstp_clrbits(type, addr, saddr, clear) \ @@ -238,13 +68,7 @@ int board_early_init_f(void) { mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125); -#if defined(CONFIG_NORFLASH) /* SCIF0 */ - set_guard_reg(GPSR4, 0x34000000, 0x00000000); - set_guard_reg(IPSR14, 0x00000FC7, 0x00000481); - set_guard_reg(GPSR4, 0x00000000, 0x34000000); -#endif - mstp_clrbits_le32(MSTPSR7, SMSTPCR7, SCIF0_MSTP721); /* ETHER */ diff --git a/board/renesas/koelsch/qos.c b/board/renesas/koelsch/qos.c index 7f88f7da8d..e6c5e48df5 100644 --- a/board/renesas/koelsch/qos.c +++ b/board/renesas/koelsch/qos.c @@ -1,7 +1,7 @@ /* * board/renesas/koelsch/qos.c * - * Copyright (C) 2013 Renesas Electronics Corporation + * Copyright (C) 2013,2014 Renesas Electronics Corporation * * SPDX-License-Identifier: GPL-2.0 * @@ -13,7 +13,7 @@ #include <asm/io.h> #include <asm/arch/rmobile.h> -/* QoS version 0.23 */ +/* QoS version 0.240 for ES1 and version 0.310 for ES2 */ enum { DBSC3_00, DBSC3_01, DBSC3_02, DBSC3_03, DBSC3_04, @@ -102,24 +102,30 @@ static u32 dbsc3_1_w_qos_addr[DBSC3_NR] = { void qos_init(void) { int i; - struct r8a7791_s3c *s3c; - struct r8a7791_s3c_qos *s3c_qos; - struct r8a7791_dbsc3_qos *qos_addr; - struct r8a7791_mxi *mxi; - struct r8a7791_mxi_qos *mxi_qos; - struct r8a7791_axi_qos *axi_qos; + struct rcar_s3c *s3c; + struct rcar_s3c_qos *s3c_qos; + struct rcar_dbsc3_qos *qos_addr; + struct rcar_mxi *mxi; + struct rcar_mxi_qos *mxi_qos; + struct rcar_axi_qos *axi_qos; /* DBSC DBADJ2 */ writel(0x20042004, DBSC3_0_DBADJ2); /* S3C -QoS */ - s3c = (struct r8a7791_s3c *)S3C_BASE; - writel(0x00FF1B1D, &s3c->s3cadsplcr); - writel(0x1F0D0C0C, &s3c->s3crorr); - writel(0x1F0D0C0A, &s3c->s3cworr); - + s3c = (struct rcar_s3c *)S3C_BASE; + if (IS_R8A7791_ES2()) { + writel(0x00FF1B0D, &s3c->s3cadsplcr); + writel(0x1F0D0B0A, &s3c->s3crorr); + writel(0x1F0D0B09, &s3c->s3cworr); + writel(0x00200808, &s3c->s3carcr11); + } else { + writel(0x00FF1B1D, &s3c->s3cadsplcr); + writel(0x1F0D0C0C, &s3c->s3crorr); + writel(0x1F0D0C0A, &s3c->s3cworr); + } /* QoS Control Registers */ - s3c_qos = (struct r8a7791_s3c_qos *)S3C_QOS_CCI0_BASE; + s3c_qos = (struct rcar_s3c_qos *)S3C_QOS_CCI0_BASE; writel(0x00890089, &s3c_qos->s3cqos0); writel(0x20960010, &s3c_qos->s3cqos1); writel(0x20302030, &s3c_qos->s3cqos2); @@ -130,7 +136,7 @@ void qos_init(void) writel(0x20AA2200, &s3c_qos->s3cqos7); writel(0x00002032, &s3c_qos->s3cqos8); - s3c_qos = (struct r8a7791_s3c_qos *)S3C_QOS_CCI1_BASE; + s3c_qos = (struct rcar_s3c_qos *)S3C_QOS_CCI1_BASE; writel(0x00890089, &s3c_qos->s3cqos0); writel(0x20960010, &s3c_qos->s3cqos1); writel(0x20302030, &s3c_qos->s3cqos2); @@ -141,8 +147,11 @@ void qos_init(void) writel(0x20AA2200, &s3c_qos->s3cqos7); writel(0x00002032, &s3c_qos->s3cqos8); - s3c_qos = (struct r8a7791_s3c_qos *)S3C_QOS_MXI_BASE; - writel(0x00820082, &s3c_qos->s3cqos0); + s3c_qos = (struct rcar_s3c_qos *)S3C_QOS_MXI_BASE; + if (IS_R8A7791_ES2()) + writel(0x80928092, &s3c_qos->s3cqos0); + else + writel(0x00820082, &s3c_qos->s3cqos0); writel(0x20960020, &s3c_qos->s3cqos1); writel(0x20302030, &s3c_qos->s3cqos2); writel(0x20AA20DC, &s3c_qos->s3cqos3); @@ -152,7 +161,7 @@ void qos_init(void) writel(0x20AA20DC, &s3c_qos->s3cqos7); writel(0x00002032, &s3c_qos->s3cqos8); - s3c_qos = (struct r8a7791_s3c_qos *)S3C_QOS_AXI_BASE; + s3c_qos = (struct rcar_s3c_qos *)S3C_QOS_AXI_BASE; writel(0x00820082, &s3c_qos->s3cqos0); writel(0x20960020, &s3c_qos->s3cqos1); writel(0x20302030, &s3c_qos->s3cqos2); @@ -166,7 +175,7 @@ void qos_init(void) /* DBSC -QoS */ /* DBSC0 - Read */ for (i = DBSC3_00; i < DBSC3_NR; i++) { - qos_addr = (struct r8a7791_dbsc3_qos *)dbsc3_0_r_qos_addr[i]; + qos_addr = (struct rcar_dbsc3_qos *)dbsc3_0_r_qos_addr[i]; writel(0x00000002, &qos_addr->dblgcnt); writel(0x00002096, &qos_addr->dbtmval0); writel(0x00002064, &qos_addr->dbtmval1); @@ -181,7 +190,7 @@ void qos_init(void) /* DBSC0 - Write */ for (i = DBSC3_00; i < DBSC3_NR; i++) { - qos_addr = (struct r8a7791_dbsc3_qos *)dbsc3_0_w_qos_addr[i]; + qos_addr = (struct rcar_dbsc3_qos *)dbsc3_0_w_qos_addr[i]; writel(0x00000002, &qos_addr->dblgcnt); writel(0x000020EB, &qos_addr->dbtmval0); writel(0x0000206E, &qos_addr->dbtmval1); @@ -196,7 +205,7 @@ void qos_init(void) /* DBSC1 - Read */ for (i = DBSC3_00; i < DBSC3_NR; i++) { - qos_addr = (struct r8a7791_dbsc3_qos *)dbsc3_1_r_qos_addr[i]; + qos_addr = (struct rcar_dbsc3_qos *)dbsc3_1_r_qos_addr[i]; writel(0x00000002, &qos_addr->dblgcnt); writel(0x00002096, &qos_addr->dbtmval0); writel(0x00002064, &qos_addr->dbtmval1); @@ -211,7 +220,7 @@ void qos_init(void) /* DBSC1 - Write */ for (i = DBSC3_00; i < DBSC3_NR; i++) { - qos_addr = (struct r8a7791_dbsc3_qos *)dbsc3_1_w_qos_addr[i]; + qos_addr = (struct rcar_dbsc3_qos *)dbsc3_1_w_qos_addr[i]; writel(0x00000002, &qos_addr->dblgcnt); writel(0x000020EB, &qos_addr->dbtmval0); writel(0x0000206E, &qos_addr->dbtmval1); @@ -232,14 +241,14 @@ void qos_init(void) /* MXI -QoS */ /* Transaction Control (MXI) */ - mxi = (struct r8a7791_mxi *)MXI_BASE; + mxi = (struct rcar_mxi *)MXI_BASE; writel(0x00000013, &mxi->mxrtcr); writel(0x00000013, &mxi->mxwtcr); writel(0x00780080, &mxi->mxsaar0); writel(0x02000800, &mxi->mxsaar1); /* QoS Control (MXI) */ - mxi_qos = (struct r8a7791_mxi_qos *)MXI_QOS_BASE; + mxi_qos = (struct rcar_mxi_qos *)MXI_QOS_BASE; writel(0x0000000C, &mxi_qos->vspdu0); writel(0x0000000C, &mxi_qos->vspdu1); writel(0x0000000D, &mxi_qos->du0); @@ -247,7 +256,7 @@ void qos_init(void) /* AXI -QoS */ /* Transaction Control (MXI) */ - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_SYX64TO128_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_SYX64TO128_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x00002245, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -259,7 +268,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_AVB_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_AVB_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x000020A6, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -268,7 +277,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_G2D_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_G2D_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x000020A6, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -277,7 +286,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_IMP0_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_IMP0_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002021, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -286,7 +295,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_IMP1_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_IMP1_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002037, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -295,7 +304,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_IMUX0_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_IMUX0_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x00002245, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -307,7 +316,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_IMUX1_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_IMUX1_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x00002245, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -319,7 +328,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_IMUX2_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_IMUX2_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x00002245, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -331,7 +340,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_LBS_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_LBS_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000214C, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -340,7 +349,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_MMUDS_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MMUDS_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002004, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -352,7 +361,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_MMUM_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MMUM_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002004, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -364,7 +373,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_MMUR_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MMUR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002004, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -376,7 +385,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_MMUS0_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MMUS0_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002004, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -388,7 +397,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_MMUS1_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MMUS1_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002004, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -400,7 +409,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_MTSB0_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MTSB0_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002021, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -409,7 +418,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_MTSB1_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MTSB1_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002021, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -418,7 +427,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_PCI_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_PCI_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000214C, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -427,7 +436,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_RTX_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_RTX_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x00002245, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -439,7 +448,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_SDS0_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_SDS0_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x000020A6, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -448,7 +457,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_SDS1_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_SDS1_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x000020A6, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -457,7 +466,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_USB20_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_USB20_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002053, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -466,7 +475,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_USB21_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_USB21_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002053, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -475,7 +484,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_USB22_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_USB22_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002053, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -484,7 +493,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_USB30_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_USB30_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000214C, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -493,7 +502,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_AX2M_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_AX2M_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x00002245, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -502,7 +511,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_CC50_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_CC50_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002029, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -511,7 +520,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_CCI_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_CCI_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x00002245, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -520,7 +529,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_CS_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_CS_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002053, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -529,7 +538,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_DDM_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_DDM_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x000020A6, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -538,7 +547,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_ETH_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_ETH_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002053, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -547,7 +556,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_MPXM_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MPXM_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x00002245, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -556,7 +565,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_SAT0_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_SAT0_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002053, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -565,7 +574,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_SAT1_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_SAT1_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002053, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -574,7 +583,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_SDM0_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_SDM0_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000214C, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -583,7 +592,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_SDM1_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_SDM1_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000214C, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -592,7 +601,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_TRAB_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_TRAB_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x000020A6, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -601,7 +610,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_UDM0_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_UDM0_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002053, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -610,7 +619,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI_UDM1_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_UDM1_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002053, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -620,7 +629,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosqon); /* QoS Register (RT-AXI) */ - axi_qos = (struct r8a7791_axi_qos *)RT_AXI_SHX_BASE; + axi_qos = (struct rcar_axi_qos *)RT_AXI_SHX_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002053, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -632,7 +641,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)RT_AXI_DBG_BASE; + axi_qos = (struct rcar_axi_qos *)RT_AXI_DBG_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002053, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -644,7 +653,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)RT_AXI_RDM_BASE; + axi_qos = (struct rcar_axi_qos *)RT_AXI_RDM_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002299, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -653,7 +662,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)RT_AXI_RDS_BASE; + axi_qos = (struct rcar_axi_qos *)RT_AXI_RDS_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002029, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -662,7 +671,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)RT_AXI_RTX64TO128_BASE; + axi_qos = (struct rcar_axi_qos *)RT_AXI_RTX64TO128_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x00002245, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -674,7 +683,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)RT_AXI_STPRO_BASE; + axi_qos = (struct rcar_axi_qos *)RT_AXI_STPRO_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002029, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -686,12 +695,9 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)RT_AXI_SY2RT_BASE; + axi_qos = (struct rcar_axi_qos *)RT_AXI_SY2RT_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x00002245, &axi_qos->qosctset0); - writel(0x00002096, &axi_qos->qosctset1); - writel(0x00002030, &axi_qos->qosctset2); - writel(0x00002030, &axi_qos->qosctset3); writel(0x00000001, &axi_qos->qosreqctr); writel(0x00002064, &axi_qos->qosthres0); writel(0x00002004, &axi_qos->qosthres1); @@ -699,7 +705,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosqon); /* QoS Register (MP-AXI) */ - axi_qos = (struct r8a7791_axi_qos *)MP_AXI_ADSP_BASE; + axi_qos = (struct rcar_axi_qos *)MP_AXI_ADSP_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002037, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -708,34 +714,34 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MP_AXI_ASDS0_BASE; + axi_qos = (struct rcar_axi_qos *)MP_AXI_ASDS0_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002014, &axi_qos->qosctset0); - writel(0x00000001, &axi_qos->qosreqctr); + writel(0x00000040, &axi_qos->qosreqctr); writel(0x00002064, &axi_qos->qosthres0); writel(0x00002004, &axi_qos->qosthres1); writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MP_AXI_ASDS1_BASE; + axi_qos = (struct rcar_axi_qos *)MP_AXI_ASDS1_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002014, &axi_qos->qosctset0); - writel(0x00000001, &axi_qos->qosreqctr); + writel(0x00000040, &axi_qos->qosreqctr); writel(0x00002064, &axi_qos->qosthres0); writel(0x00002004, &axi_qos->qosthres1); writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MP_AXI_MLP_BASE; - writel(0x00000000, &axi_qos->qosconf); - writel(0x00002014, &axi_qos->qosctset0); - writel(0x00000001, &axi_qos->qosreqctr); + axi_qos = (struct rcar_axi_qos *)MP_AXI_MLP_BASE; + writel(0x00000001, &axi_qos->qosconf); + writel(0x00001FF0, &axi_qos->qosctset0); + writel(0x00000020, &axi_qos->qosreqctr); writel(0x00002064, &axi_qos->qosthres0); writel(0x00002004, &axi_qos->qosthres1); - writel(0x00000000, &axi_qos->qosthres2); + writel(0x00002001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MP_AXI_MMUMP_BASE; + axi_qos = (struct rcar_axi_qos *)MP_AXI_MMUMP_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002004, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -747,7 +753,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MP_AXI_SPU_BASE; + axi_qos = (struct rcar_axi_qos *)MP_AXI_SPU_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002053, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -756,7 +762,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MP_AXI_SPUC_BASE; + axi_qos = (struct rcar_axi_qos *)MP_AXI_SPUC_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000206E, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -766,9 +772,12 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosqon); /* QoS Register (SYS-AXI256) */ - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI256_AXI128TO256_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI256_AXI128TO256_BASE; writel(0x00000002, &axi_qos->qosconf); - writel(0x00002245, &axi_qos->qosctset0); + if (IS_R8A7791_ES2()) + writel(0x000020EB, &axi_qos->qosctset0); + else + writel(0x00002245, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); writel(0x00002030, &axi_qos->qosctset2); writel(0x00002030, &axi_qos->qosctset3); @@ -778,9 +787,12 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI256_SYX_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI256_SYX_BASE; writel(0x00000002, &axi_qos->qosconf); - writel(0x00002245, &axi_qos->qosctset0); + if (IS_R8A7791_ES2()) + writel(0x000020EB, &axi_qos->qosctset0); + else + writel(0x00002245, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); writel(0x00002030, &axi_qos->qosctset2); writel(0x00002030, &axi_qos->qosctset3); @@ -790,9 +802,12 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI256_MPX_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI256_MPX_BASE; writel(0x00000002, &axi_qos->qosconf); - writel(0x00002245, &axi_qos->qosctset0); + if (IS_R8A7791_ES2()) + writel(0x000020EB, &axi_qos->qosctset0); + else + writel(0x00002245, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); writel(0x00002030, &axi_qos->qosctset2); writel(0x00002030, &axi_qos->qosctset3); @@ -802,7 +817,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)SYS_AXI256_MXI_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI256_MXI_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x00002245, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -815,7 +830,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosqon); /* QoS Register (CCI-AXI) */ - axi_qos = (struct r8a7791_axi_qos *)CCI_AXI_MMUS0_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MMUS0_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002004, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -827,7 +842,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)CCI_AXI_SYX2_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_SYX2_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x00002245, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -839,7 +854,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)CCI_AXI_MMUR_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MMUR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002004, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -851,7 +866,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)CCI_AXI_MMUDS_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MMUDS_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002004, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -863,7 +878,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)CCI_AXI_MMUM_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MMUM_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002004, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -875,7 +890,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)CCI_AXI_MXI_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MXI_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x00002245, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -887,7 +902,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)CCI_AXI_MMUS1_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MMUS1_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002004, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -899,7 +914,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)CCI_AXI_MMUMP_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MMUMP_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002004, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -912,7 +927,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosqon); /* QoS Register (Media-AXI) */ - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_MXR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_MXR_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x000020DC, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -923,7 +938,7 @@ void qos_init(void) writel(0x00002032, &axi_qos->qosthres1); writel(0x00000001, &axi_qos->qosthres2); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_MXW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_MXW_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x000020DC, &axi_qos->qosctset0); writel(0x00002096, &axi_qos->qosctset1); @@ -934,7 +949,7 @@ void qos_init(void) writel(0x00002032, &axi_qos->qosthres1); writel(0x00000001, &axi_qos->qosthres2); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_JPR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_JPR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002190, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -943,16 +958,21 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_JPW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_JPW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002190, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); - writel(0x00002064, &axi_qos->qosthres0); - writel(0x00002004, &axi_qos->qosthres1); + if (IS_R8A7791_ES2()) { + writel(0x00000001, &axi_qos->qosthres0); + writel(0x00000001, &axi_qos->qosthres1); + } else { + writel(0x00002064, &axi_qos->qosthres0); + writel(0x00002004, &axi_qos->qosthres1); + } writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_TDMR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_TDMR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002190, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -961,7 +981,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_TDMW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_TDMW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002190, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -970,7 +990,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VSP1CR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSP1CR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002190, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -979,16 +999,21 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VSP1CW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSP1CW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002190, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); - writel(0x00002064, &axi_qos->qosthres0); - writel(0x00002004, &axi_qos->qosthres1); + if (IS_R8A7791_ES2()) { + writel(0x00000001, &axi_qos->qosthres0); + writel(0x00000001, &axi_qos->qosthres1); + } else { + writel(0x00002064, &axi_qos->qosthres0); + writel(0x00002004, &axi_qos->qosthres1); + } writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VSPDU0CR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPDU0CR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002190, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -997,16 +1022,21 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VSPDU0CW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPDU0CW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002190, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); - writel(0x00002064, &axi_qos->qosthres0); - writel(0x00002004, &axi_qos->qosthres1); + if (IS_R8A7791_ES2()) { + writel(0x00000001, &axi_qos->qosthres0); + writel(0x00000001, &axi_qos->qosthres1); + } else { + writel(0x00002064, &axi_qos->qosthres0); + writel(0x00002004, &axi_qos->qosthres1); + } writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VSPDU1CR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPDU1CR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002190, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1015,25 +1045,36 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VSPDU1CW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPDU1CW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002190, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); - writel(0x00002064, &axi_qos->qosthres0); - writel(0x00002004, &axi_qos->qosthres1); + if (IS_R8A7791_ES2()) { + writel(0x00000001, &axi_qos->qosthres0); + writel(0x00000001, &axi_qos->qosthres1); + } else { + writel(0x00002064, &axi_qos->qosthres0); + writel(0x00002004, &axi_qos->qosthres1); + } writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VIN0W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VIN0W_BASE; writel(0x00000001, &axi_qos->qosconf); - writel(0x000020C8, &axi_qos->qosctset0); + if (IS_R8A7791_ES2()) + writel(0x00001FF0, &axi_qos->qosctset0); + else + writel(0x000020C8, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); writel(0x00002064, &axi_qos->qosthres0); writel(0x00002004, &axi_qos->qosthres1); - writel(0x00000001, &axi_qos->qosthres2); + if (IS_R8A7791_ES2()) + writel(0x00002001, &axi_qos->qosthres2); + else + writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_FDP0R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_FDP0R_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1042,16 +1083,21 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_FDP0W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_FDP0W_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); - writel(0x00002064, &axi_qos->qosthres0); - writel(0x00002004, &axi_qos->qosthres1); + if (IS_R8A7791_ES2()) { + writel(0x00000001, &axi_qos->qosthres0); + writel(0x00000001, &axi_qos->qosthres1); + } else { + writel(0x00002064, &axi_qos->qosthres0); + writel(0x00002004, &axi_qos->qosthres1); + } writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_IMSR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_IMSR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1060,7 +1106,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_IMSW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_IMSW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1069,7 +1115,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VSP1R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSP1R_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1078,16 +1124,21 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VSP1W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSP1W_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); - writel(0x00002064, &axi_qos->qosthres0); - writel(0x00002004, &axi_qos->qosthres1); + if (IS_R8A7791_ES2()) { + writel(0x00000001, &axi_qos->qosthres0); + writel(0x00000001, &axi_qos->qosthres1); + } else { + writel(0x00002064, &axi_qos->qosthres0); + writel(0x00002004, &axi_qos->qosthres1); + } writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_FDP1R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_FDP1R_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1096,16 +1147,21 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_FDP1W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_FDP1W_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); - writel(0x00002064, &axi_qos->qosthres0); - writel(0x00002004, &axi_qos->qosthres1); + if (IS_R8A7791_ES2()) { + writel(0x00000001, &axi_qos->qosthres0); + writel(0x00000001, &axi_qos->qosthres1); + } else { + writel(0x00002064, &axi_qos->qosthres0); + writel(0x00002004, &axi_qos->qosthres1); + } writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_IMRR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_IMRR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1114,7 +1170,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_IMRW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_IMRW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1123,40 +1179,55 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VSPD0R_BASE; - writel(0x00000000, &axi_qos->qosconf); + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPD0R_BASE; + if (IS_R8A7791_ES2()) + writel(0x00000003, &axi_qos->qosconf); + else + writel(0x00000000, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00002064, &axi_qos->qosthres0); writel(0x00002004, &axi_qos->qosthres1); writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VSPD0W_BASE; - writel(0x00000000, &axi_qos->qosconf); + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPD0W_BASE; + if (IS_R8A7791_ES2()) + writel(0x00000003, &axi_qos->qosconf); + else + writel(0x00000000, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00002064, &axi_qos->qosthres0); writel(0x00002004, &axi_qos->qosthres1); writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VSPD1R_BASE; - writel(0x00000000, &axi_qos->qosconf); + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPD1R_BASE; + if (IS_R8A7791_ES2()) + writel(0x00000003, &axi_qos->qosconf); + else + writel(0x00000000, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00002064, &axi_qos->qosthres0); writel(0x00002004, &axi_qos->qosthres1); writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VSPD1W_BASE; - writel(0x00000000, &axi_qos->qosconf); + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPD1W_BASE; + if (IS_R8A7791_ES2()) + writel(0x00000003, &axi_qos->qosconf); + else + writel(0x00000000, &axi_qos->qosconf); writel(0x000020C8, &axi_qos->qosctset0); writel(0x00002064, &axi_qos->qosthres0); writel(0x00002004, &axi_qos->qosthres1); writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_DU0R_BASE; - writel(0x00000000, &axi_qos->qosconf); + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_DU0R_BASE; + if (IS_R8A7791_ES2()) + writel(0x00000003, &axi_qos->qosconf); + else + writel(0x00000000, &axi_qos->qosconf); writel(0x00002063, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); writel(0x00002064, &axi_qos->qosthres0); @@ -1164,8 +1235,11 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_DU0W_BASE; - writel(0x00000000, &axi_qos->qosconf); + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_DU0W_BASE; + if (IS_R8A7791_ES2()) + writel(0x00000000, &axi_qos->qosconf); + else + writel(0x00000000, &axi_qos->qosconf); writel(0x00002063, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); writel(0x00002064, &axi_qos->qosthres0); @@ -1173,7 +1247,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VCP0CR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VCP0CR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002073, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1182,16 +1256,21 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VCP0CW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VCP0CW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002073, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); - writel(0x00002064, &axi_qos->qosthres0); - writel(0x00002004, &axi_qos->qosthres1); + if (IS_R8A7791_ES2()) { + writel(0x00000001, &axi_qos->qosthres0); + writel(0x00000001, &axi_qos->qosthres1); + } else { + writel(0x00002064, &axi_qos->qosthres0); + writel(0x00002004, &axi_qos->qosthres1); + } writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VCP0VR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VCP0VR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002073, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1200,16 +1279,21 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VCP0VW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VCP0VW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002073, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); - writel(0x00002064, &axi_qos->qosthres0); - writel(0x00002004, &axi_qos->qosthres1); + if (IS_R8A7791_ES2()) { + writel(0x00000001, &axi_qos->qosthres0); + writel(0x00000001, &axi_qos->qosthres1); + } else { + writel(0x00002064, &axi_qos->qosthres0); + writel(0x00002004, &axi_qos->qosthres1); + } writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7791_axi_qos *)MEDIA_AXI_VPC0R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VPC0R_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002073, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); diff --git a/board/renesas/lager/lager.c b/board/renesas/lager/lager.c index ad5289a23b..a5a0474cd7 100644 --- a/board/renesas/lager/lager.c +++ b/board/renesas/lager/lager.c @@ -24,181 +24,23 @@ DECLARE_GLOBAL_DATA_PTR; -#define s_init_wait(cnt) \ - ({ \ - u32 i = 0x10000 * cnt; \ - while (i > 0) \ - i--; \ - }) - -#define dbpdrgd_check(bsc) \ - ({ \ - while ((readl(&bsc->dbpdrgd) & 0x1) != 0x1) \ - ; \ - }) - -#if defined(CONFIG_NORFLASH) -static void bsc_init(void) -{ - struct r8a7790_lbsc *lbsc = (struct r8a7790_lbsc *)LBSC_BASE; - struct r8a7790_dbsc3 *dbsc3_0 = (struct r8a7790_dbsc3 *)DBSC3_0_BASE; - - /* LBSC */ - writel(0x00000020, &lbsc->cs0ctrl); - writel(0x00000020, &lbsc->cs1ctrl); - writel(0x00002020, &lbsc->ecs0ctrl); - writel(0x00002020, &lbsc->ecs1ctrl); - - writel(0x077F077F, &lbsc->cswcr0); - writel(0x077F077F, &lbsc->cswcr1); - writel(0x077F077F, &lbsc->ecswcr0); - writel(0x077F077F, &lbsc->ecswcr1); - - /* DBSC3 */ - s_init_wait(10); - - writel(0x0000A55A, &dbsc3_0->dbpdlck); - writel(0x00000001, &dbsc3_0->dbpdrga); - writel(0x80000000, &dbsc3_0->dbpdrgd); - writel(0x00000004, &dbsc3_0->dbpdrga); - dbpdrgd_check(dbsc3_0); - - writel(0x00000006, &dbsc3_0->dbpdrga); - writel(0x0001C000, &dbsc3_0->dbpdrgd); - - writel(0x00000023, &dbsc3_0->dbpdrga); - writel(0x00FD2480, &dbsc3_0->dbpdrgd); - - writel(0x00000010, &dbsc3_0->dbpdrga); - writel(0xF004649B, &dbsc3_0->dbpdrgd); - - writel(0x0000000F, &dbsc3_0->dbpdrga); - writel(0x00181EE4, &dbsc3_0->dbpdrgd); - - writel(0x0000000E, &dbsc3_0->dbpdrga); - writel(0x33C03812, &dbsc3_0->dbpdrgd); - - writel(0x00000003, &dbsc3_0->dbpdrga); - writel(0x0300C481, &dbsc3_0->dbpdrgd); - - writel(0x00000007, &dbsc3_0->dbkind); - writel(0x10030A02, &dbsc3_0->dbconf0); - writel(0x00000001, &dbsc3_0->dbphytype); - writel(0x00000000, &dbsc3_0->dbbl); - writel(0x0000000B, &dbsc3_0->dbtr0); - writel(0x00000008, &dbsc3_0->dbtr1); - writel(0x00000000, &dbsc3_0->dbtr2); - writel(0x0000000B, &dbsc3_0->dbtr3); - writel(0x000C000B, &dbsc3_0->dbtr4); - writel(0x00000027, &dbsc3_0->dbtr5); - writel(0x0000001C, &dbsc3_0->dbtr6); - writel(0x00000005, &dbsc3_0->dbtr7); - writel(0x00000018, &dbsc3_0->dbtr8); - writel(0x00000008, &dbsc3_0->dbtr9); - writel(0x0000000C, &dbsc3_0->dbtr10); - writel(0x00000009, &dbsc3_0->dbtr11); - writel(0x00000012, &dbsc3_0->dbtr12); - writel(0x000000D0, &dbsc3_0->dbtr13); - writel(0x00140005, &dbsc3_0->dbtr14); - writel(0x00050004, &dbsc3_0->dbtr15); - writel(0x70233005, &dbsc3_0->dbtr16); - writel(0x000C0000, &dbsc3_0->dbtr17); - writel(0x00000300, &dbsc3_0->dbtr18); - writel(0x00000040, &dbsc3_0->dbtr19); - writel(0x00000001, &dbsc3_0->dbrnk0); - writel(0x00020001, &dbsc3_0->dbadj0); - writel(0x20082008, &dbsc3_0->dbadj2); - writel(0x00020002, &dbsc3_0->dbwt0cnf0); - writel(0x0000000F, &dbsc3_0->dbwt0cnf4); - - writel(0x00000015, &dbsc3_0->dbpdrga); - writel(0x00000D70, &dbsc3_0->dbpdrgd); - - writel(0x00000016, &dbsc3_0->dbpdrga); - writel(0x00000006, &dbsc3_0->dbpdrgd); - - writel(0x00000017, &dbsc3_0->dbpdrga); - writel(0x00000018, &dbsc3_0->dbpdrgd); - - writel(0x00000012, &dbsc3_0->dbpdrga); - writel(0x9D5CBB66, &dbsc3_0->dbpdrgd); - - writel(0x00000013, &dbsc3_0->dbpdrga); - writel(0x1A868300, &dbsc3_0->dbpdrgd); - - writel(0x00000023, &dbsc3_0->dbpdrga); - writel(0x00FDB6C0, &dbsc3_0->dbpdrgd); - - writel(0x00000014, &dbsc3_0->dbpdrga); - writel(0x300214D8, &dbsc3_0->dbpdrgd); - - writel(0x0000001A, &dbsc3_0->dbpdrga); - writel(0x930035C7, &dbsc3_0->dbpdrgd); - - writel(0x00000060, &dbsc3_0->dbpdrga); - writel(0x330657B2, &dbsc3_0->dbpdrgd); - - writel(0x00000011, &dbsc3_0->dbpdrga); - writel(0x1000040B, &dbsc3_0->dbpdrgd); - - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x00000001, &dbsc3_0->dbpdrga); - writel(0x00000071, &dbsc3_0->dbpdrgd); - - writel(0x00000004, &dbsc3_0->dbpdrga); - dbpdrgd_check(dbsc3_0); - - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x2100FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - writel(0x0000FA00, &dbsc3_0->dbcmd); - - writel(0x110000DB, &dbsc3_0->dbcmd); - - writel(0x00000001, &dbsc3_0->dbpdrga); - writel(0x00000181, &dbsc3_0->dbpdrgd); - - writel(0x00000004, &dbsc3_0->dbpdrga); - dbpdrgd_check(dbsc3_0); - - writel(0x00000001, &dbsc3_0->dbpdrga); - writel(0x0000FE01, &dbsc3_0->dbpdrgd); - - writel(0x00000004, &dbsc3_0->dbpdrga); - dbpdrgd_check(dbsc3_0); - - writel(0x00000000, &dbsc3_0->dbbs0cnt1); - writel(0x01004C20, &dbsc3_0->dbcalcnf); - writel(0x014000AA, &dbsc3_0->dbcaltr); - writel(0x00000140, &dbsc3_0->dbrfcnf0); - writel(0x00081860, &dbsc3_0->dbrfcnf1); - writel(0x00010000, &dbsc3_0->dbrfcnf2); - writel(0x00000001, &dbsc3_0->dbrfen); - writel(0x00000001, &dbsc3_0->dbacen); -} -#else -#define bsc_init() do {} while (0) -#endif /* CONFIG_NORFLASH */ - +#define CLK2MHZ(clk) (clk / 1000 / 1000) void s_init(void) { - struct r8a7790_rwdt *rwdt = (struct r8a7790_rwdt *)RWDT_BASE; - struct r8a7790_swdt *swdt = (struct r8a7790_swdt *)SWDT_BASE; + struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE; + struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE; + u32 stc; /* Watchdog init */ writel(0xA5A5A500, &rwdt->rwtcsra); writel(0xA5A5A500, &swdt->swtcsra); + /* CPU frequency setting. Set to 1.4GHz */ + stc = ((1500 / CLK2MHZ(CONFIG_SYS_CLK_FREQ)) - 1) << PLL0_STC_BIT; + clrsetbits_le32(PLL0CR, PLL0_STC_MASK, stc); + /* QoS(Quality-of-Service) Init */ qos_init(); - - /* BSC init */ - bsc_init(); } #define MSTPSR1 0xE6150038 @@ -213,18 +55,6 @@ void s_init(void) #define SMSTPCR8 0xE6150990 #define ETHER_MSTP813 (1 << 13) -#define PMMR 0xE6060000 -#define GPSR4 0xE6060014 -#define IPSR14 0xE6060058 - -#define set_guard_reg(addr, mask, value) \ -{ \ - u32 val; \ - val = (readl(addr) & ~(mask)) | (value); \ - writel(~val, PMMR); \ - writel(val, addr); \ -} - #define mstp_setbits(type, addr, saddr, set) \ out_##type((saddr), in_##type(addr) | (set)) #define mstp_clrbits(type, addr, saddr, clear) \ @@ -238,16 +68,8 @@ int board_early_init_f(void) { /* TMU0 */ mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125); - -#if defined(CONFIG_NORFLASH) /* SCIF0 */ - set_guard_reg(GPSR4, 0x34000000, 0x00000000); - set_guard_reg(IPSR14, 0x00000FC7, 0x00000481); - set_guard_reg(GPSR4, 0x00000000, 0x34000000); -#endif - mstp_clrbits_le32(MSTPSR7, SMSTPCR7, SCIF0_MSTP721); - /* ETHER */ mstp_clrbits_le32(MSTPSR8, SMSTPCR8, ETHER_MSTP813); @@ -263,8 +85,6 @@ void arch_preboot_os(void) DECLARE_GLOBAL_DATA_PTR; int board_init(void) { - /* board id for linux */ - gd->bd->bi_arch_number = MACH_TYPE_LAGER; /* adress of boot parameters */ gd->bd->bi_boot_params = LAGER_SDRAM_BASE + 0x100; diff --git a/board/renesas/lager/qos.c b/board/renesas/lager/qos.c index b88511a326..374275747d 100644 --- a/board/renesas/lager/qos.c +++ b/board/renesas/lager/qos.c @@ -1,7 +1,7 @@ /* * board/renesas/lager/qos.c * - * Copyright (C) 2013 Renesas Electronics Corporation + * Copyright (C) 2013,2014 Renesas Electronics Corporation * * SPDX-License-Identifier: GPL-2.0 */ @@ -12,7 +12,7 @@ #include <asm/io.h> #include <asm/arch/rmobile.h> -/* QoS version 0.954 */ +/* QoS version 0.955 */ enum { DBSC3_R00, DBSC3_R01, DBSC3_R02, DBSC3_R03, DBSC3_R04, @@ -64,24 +64,24 @@ static const u32 dbsc3_qos_addr[DBSC3_NR] = { void qos_init(void) { int i; - struct r8a7790_s3c *s3c; - struct r8a7790_s3c_qos *s3c_qos; - struct r8a7790_dbsc3_qos *qos_addr; - struct r8a7790_mxi *mxi; - struct r8a7790_mxi_qos *mxi_qos; - struct r8a7790_axi_qos *axi_qos; + struct rcar_s3c *s3c; + struct rcar_s3c_qos *s3c_qos; + struct rcar_dbsc3_qos *qos_addr; + struct rcar_mxi *mxi; + struct rcar_mxi_qos *mxi_qos; + struct rcar_axi_qos *axi_qos; /* DBSC DBADJ2 */ writel(0x20042004, DBSC3_0_DBADJ2); /* S3C -QoS */ - s3c = (struct r8a7790_s3c *)S3C_BASE; + s3c = (struct rcar_s3c *)S3C_BASE; writel(0x80FF1C1E, &s3c->s3cadsplcr); writel(0x1F060505, &s3c->s3crorr); writel(0x1F020100, &s3c->s3cworr); /* QoS Control Registers */ - s3c_qos = (struct r8a7790_s3c_qos *)S3C_QOS_CCI0_BASE; + s3c_qos = (struct rcar_s3c_qos *)S3C_QOS_CCI0_BASE; writel(0x00800080, &s3c_qos->s3cqos0); writel(0x22000010, &s3c_qos->s3cqos1); writel(0x22002200, &s3c_qos->s3cqos2); @@ -92,7 +92,7 @@ void qos_init(void) writel(0x2F002200, &s3c_qos->s3cqos7); writel(0x2F002F00, &s3c_qos->s3cqos8); - s3c_qos = (struct r8a7790_s3c_qos *)S3C_QOS_CCI1_BASE; + s3c_qos = (struct rcar_s3c_qos *)S3C_QOS_CCI1_BASE; writel(0x00800080, &s3c_qos->s3cqos0); writel(0x22000010, &s3c_qos->s3cqos1); writel(0x22002200, &s3c_qos->s3cqos2); @@ -103,7 +103,7 @@ void qos_init(void) writel(0x2F002200, &s3c_qos->s3cqos7); writel(0x2F002F00, &s3c_qos->s3cqos8); - s3c_qos = (struct r8a7790_s3c_qos *)S3C_QOS_MXI_BASE; + s3c_qos = (struct rcar_s3c_qos *)S3C_QOS_MXI_BASE; writel(0x80918099, &s3c_qos->s3cqos0); writel(0x20410010, &s3c_qos->s3cqos1); writel(0x200A2023, &s3c_qos->s3cqos2); @@ -114,7 +114,7 @@ void qos_init(void) writel(0x20502001, &s3c_qos->s3cqos7); writel(0x20142032, &s3c_qos->s3cqos8); - s3c_qos = (struct r8a7790_s3c_qos *)S3C_QOS_AXI_BASE; + s3c_qos = (struct rcar_s3c_qos *)S3C_QOS_AXI_BASE; writel(0x00810089, &s3c_qos->s3cqos0); writel(0x20410001, &s3c_qos->s3cqos1); @@ -131,7 +131,7 @@ void qos_init(void) /* DBSC -QoS */ /* DBSC0 - Read/Write */ for (i = DBSC3_R00; i < DBSC3_NR; i++) { - qos_addr = (struct r8a7790_dbsc3_qos *)dbsc3_qos_addr[i]; + qos_addr = (struct rcar_dbsc3_qos *)dbsc3_qos_addr[i]; writel(0x00000203, &qos_addr->dblgcnt); writel(0x00002064, &qos_addr->dbtmval0); writel(0x00002048, &qos_addr->dbtmval1); @@ -151,7 +151,7 @@ void qos_init(void) /* MXI -QoS */ /* Transaction Control (MXI) */ - mxi = (struct r8a7790_mxi *)MXI_BASE; + mxi = (struct rcar_mxi *)MXI_BASE; writel(0x00000013, &mxi->mxrtcr); writel(0x00000013, &mxi->mxwtcr); writel(0x00B800C0, &mxi->mxsaar0); @@ -162,7 +162,7 @@ void qos_init(void) writel(0x00200000, &mxi->mxaxiwacr); /* QoS Control (MXI) */ - mxi_qos = (struct r8a7790_mxi_qos *)MXI_QOS_BASE; + mxi_qos = (struct rcar_mxi_qos *)MXI_QOS_BASE; writel(0x0000000C, &mxi_qos->vspdu0); writel(0x0000000C, &mxi_qos->vspdu1); writel(0x0000000D, &mxi_qos->du0); @@ -170,7 +170,7 @@ void qos_init(void) /* AXI -QoS */ /* Transaction Control (MXI) */ - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_SYX64TO128_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_SYX64TO128_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x0000200F, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -182,7 +182,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_AVB_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_AVB_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000200A, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -191,7 +191,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_G2D_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_G2D_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000200A, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -200,7 +200,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_IMP0_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_IMP0_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002002, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -209,7 +209,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_IMP1_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_IMP1_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002004, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -218,7 +218,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_IMUX0_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_IMUX0_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x0000200F, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -230,7 +230,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_IMUX1_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_IMUX1_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x0000200F, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -242,7 +242,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_IMUX2_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_IMUX2_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x0000200F, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -254,7 +254,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_LBS_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_LBS_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002014, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -263,7 +263,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_MMUDS_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MMUDS_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002001, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -275,7 +275,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_MMUM_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MMUM_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002001, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -287,7 +287,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_MMUR_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MMUR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002001, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -299,7 +299,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_MMUS0_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MMUS0_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002001, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -311,7 +311,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_MMUS1_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MMUS1_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002001, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -323,7 +323,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_MTSB0_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MTSB0_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002002, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -332,7 +332,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_MTSB1_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_MTSB1_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002002, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -341,7 +341,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_PCI_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_PCI_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002014, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -350,7 +350,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_RTX_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_RTX_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x0000200F, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -362,7 +362,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_SDS0_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_SDS0_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000200A, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -371,7 +371,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_SDS1_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_SDS1_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000200A, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -380,7 +380,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_USB20_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_USB20_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002005, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -389,7 +389,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_USB21_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_USB21_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002005, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -398,7 +398,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_USB22_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_USB22_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002005, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -407,7 +407,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI_USB30_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI_USB30_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002014, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -417,7 +417,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosqon); /* QoS Register (RT-AXI) */ - axi_qos = (struct r8a7790_axi_qos *)RT_AXI_SHX_BASE; + axi_qos = (struct rcar_axi_qos *)RT_AXI_SHX_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002005, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -429,7 +429,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)RT_AXI_RDS_BASE; + axi_qos = (struct rcar_axi_qos *)RT_AXI_RDS_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002007, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -438,7 +438,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)RT_AXI_RTX64TO128_BASE; + axi_qos = (struct rcar_axi_qos *)RT_AXI_RTX64TO128_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x0000200F, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -450,7 +450,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)RT_AXI_STPRO_BASE; + axi_qos = (struct rcar_axi_qos *)RT_AXI_STPRO_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002003, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -463,7 +463,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosqon); /* QoS Register (MP-AXI) */ - axi_qos = (struct r8a7790_axi_qos *)MP_AXI_ADSP_BASE; + axi_qos = (struct rcar_axi_qos *)MP_AXI_ADSP_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002007, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -472,34 +472,34 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MP_AXI_ASDS0_BASE; + axi_qos = (struct rcar_axi_qos *)MP_AXI_ASDS0_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002014, &axi_qos->qosctset0); - writel(0x00000001, &axi_qos->qosreqctr); + writel(0x00000040, &axi_qos->qosreqctr); writel(0x00002006, &axi_qos->qosthres0); writel(0x00002001, &axi_qos->qosthres1); writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MP_AXI_ASDS1_BASE; + axi_qos = (struct rcar_axi_qos *)MP_AXI_ASDS1_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002014, &axi_qos->qosctset0); - writel(0x00000001, &axi_qos->qosreqctr); + writel(0x00000040, &axi_qos->qosreqctr); writel(0x00002006, &axi_qos->qosthres0); writel(0x00002001, &axi_qos->qosthres1); writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MP_AXI_MLP_BASE; - writel(0x00000000, &axi_qos->qosconf); - writel(0x00002002, &axi_qos->qosctset0); - writel(0x00000001, &axi_qos->qosreqctr); + axi_qos = (struct rcar_axi_qos *)MP_AXI_MLP_BASE; + writel(0x00000001, &axi_qos->qosconf); + writel(0x00001FF0, &axi_qos->qosctset0); + writel(0x00000020, &axi_qos->qosreqctr); writel(0x00002006, &axi_qos->qosthres0); writel(0x00002001, &axi_qos->qosthres1); - writel(0x00000000, &axi_qos->qosthres2); + writel(0x00002001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MP_AXI_MMUMP_BASE; + axi_qos = (struct rcar_axi_qos *)MP_AXI_MMUMP_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002001, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -511,7 +511,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MP_AXI_SPU_BASE; + axi_qos = (struct rcar_axi_qos *)MP_AXI_SPU_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -520,7 +520,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MP_AXI_SPUC_BASE; + axi_qos = (struct rcar_axi_qos *)MP_AXI_SPUC_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000200D, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -530,7 +530,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosqon); /* QoS Register (SYS-AXI256) */ - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI256_AXI128TO256_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI256_AXI128TO256_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x0000200F, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -542,7 +542,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI256_SYX_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI256_SYX_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x0000200F, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -554,7 +554,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI256_MPX_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI256_MPX_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x0000200F, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -566,7 +566,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)SYS_AXI256_MXI_BASE; + axi_qos = (struct rcar_axi_qos *)SYS_AXI256_MXI_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x0000200F, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -579,7 +579,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosqon); /* QoS Register (CCI-AXI) */ - axi_qos = (struct r8a7790_axi_qos *)CCI_AXI_MMUS0_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MMUS0_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002001, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -591,7 +591,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)CCI_AXI_SYX2_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_SYX2_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x0000200F, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -603,7 +603,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)CCI_AXI_MMUR_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MMUR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002001, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -615,7 +615,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)CCI_AXI_MMUDS_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MMUDS_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002001, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -627,7 +627,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)CCI_AXI_MMUM_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MMUM_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002001, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -639,7 +639,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)CCI_AXI_MXI_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MXI_BASE; writel(0x00000002, &axi_qos->qosconf); writel(0x0000200F, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -651,7 +651,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)CCI_AXI_MMUS1_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MMUS1_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002001, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -663,7 +663,7 @@ void qos_init(void) writel(0x00000000, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)CCI_AXI_MMUMP_BASE; + axi_qos = (struct rcar_axi_qos *)CCI_AXI_MMUMP_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002001, &axi_qos->qosctset0); writel(0x00002009, &axi_qos->qosctset1); @@ -676,7 +676,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosqon); /* QoS Register (Media-AXI) */ - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_JPR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_JPR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -685,7 +685,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_JPW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_JPW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -694,7 +694,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_GCU0R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_GCU0R_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -703,7 +703,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_GCU0W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_GCU0W_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -712,7 +712,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_GCU1R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_GCU1R_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -721,7 +721,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_GCU1W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_GCU1W_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -730,7 +730,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_TDMR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_TDMR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -739,7 +739,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_TDMW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_TDMW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -748,7 +748,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSP0CR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSP0CR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -757,7 +757,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSP0CW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSP0CW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -766,7 +766,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSP1CR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSP1CR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -775,7 +775,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSP1CW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSP1CW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -784,7 +784,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSPDU0CR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPDU0CR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -793,7 +793,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSPDU0CW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPDU0CW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -802,7 +802,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSPDU1CR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPDU1CR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -811,7 +811,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSPDU1CW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPDU1CW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002018, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -820,7 +820,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VIN0W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VIN0W_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -829,7 +829,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSP0R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSP0R_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -838,7 +838,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSP0W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSP0W_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -847,7 +847,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_FDP0R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_FDP0R_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -856,7 +856,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_FDP0W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_FDP0W_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -865,7 +865,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_IMSR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_IMSR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -874,7 +874,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_IMSW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_IMSW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -883,7 +883,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSP1R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSP1R_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -892,7 +892,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSP1W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSP1W_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -901,7 +901,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_FDP1R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_FDP1R_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -910,7 +910,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_FDP1W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_FDP1W_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -919,7 +919,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_IMRR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_IMRR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -928,7 +928,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_IMRW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_IMRW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -937,7 +937,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_FDP2R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_FDP2R_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -946,7 +946,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_FDP2W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_FDP2W_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -955,7 +955,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSPD0R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPD0R_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -964,7 +964,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSPD0W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPD0W_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -973,7 +973,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSPD1R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPD1R_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -982,7 +982,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VSPD1W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VSPD1W_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -991,7 +991,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_DU0R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_DU0R_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -1000,7 +1000,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_DU0W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_DU0W_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -1009,7 +1009,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_DU1R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_DU1R_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -1018,7 +1018,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_DU1W_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_DU1W_BASE; writel(0x00000000, &axi_qos->qosconf); writel(0x0000200C, &axi_qos->qosctset0); writel(0x00000001, &axi_qos->qosreqctr); @@ -1027,7 +1027,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VCP0CR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VCP0CR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002007, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1036,7 +1036,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VCP0CW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VCP0CW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002007, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1045,7 +1045,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VCP0VR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VCP0VR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002007, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1054,7 +1054,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VCP0VW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VCP0VW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002007, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1063,7 +1063,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VPC0R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VPC0R_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002007, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1072,7 +1072,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VCP1CR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VCP1CR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002007, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1081,7 +1081,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VCP1CW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VCP1CW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002007, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1090,7 +1090,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VCP1VR_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VCP1VR_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002007, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1099,7 +1099,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VCP1VW_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VCP1VW_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002007, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); @@ -1108,7 +1108,7 @@ void qos_init(void) writel(0x00000001, &axi_qos->qosthres2); writel(0x00000001, &axi_qos->qosqon); - axi_qos = (struct r8a7790_axi_qos *)MEDIA_AXI_VPC1R_BASE; + axi_qos = (struct rcar_axi_qos *)MEDIA_AXI_VPC1R_BASE; writel(0x00000001, &axi_qos->qosconf); writel(0x00002007, &axi_qos->qosctset0); writel(0x00000020, &axi_qos->qosreqctr); diff --git a/board/samsung/arndale/arndale.c b/board/samsung/arndale/arndale.c index 9efc355dab..ef88314f7d 100644 --- a/board/samsung/arndale/arndale.c +++ b/board/samsung/arndale/arndale.c @@ -16,17 +16,14 @@ DECLARE_GLOBAL_DATA_PTR; #ifdef CONFIG_USB_EHCI_EXYNOS int board_usb_init(int index, enum usb_init_type init) { - struct exynos5_gpio_part1 *gpio = (struct exynos5_gpio_part1 *) - samsung_get_base_gpio_part1(); - /* Configure gpios for usb 3503 hub: * disconnect, toggle reset and connect */ - s5p_gpio_direction_output(&gpio->d1, 7, 0); - s5p_gpio_direction_output(&gpio->x3, 5, 0); + gpio_direction_output(EXYNOS5_GPIO_D17, 0); + gpio_direction_output(EXYNOS5_GPIO_X35, 0); - s5p_gpio_direction_output(&gpio->x3, 5, 1); - s5p_gpio_direction_output(&gpio->d1, 7, 1); + gpio_direction_output(EXYNOS5_GPIO_X35, 1); + gpio_direction_output(EXYNOS5_GPIO_D17, 1); return 0; } diff --git a/board/samsung/common/Makefile b/board/samsung/common/Makefile index 7d2bb8c4a2..41d0cc3814 100644 --- a/board/samsung/common/Makefile +++ b/board/samsung/common/Makefile @@ -7,7 +7,6 @@ obj-$(CONFIG_SOFT_I2C_MULTI_BUS) += multi_i2c.o obj-$(CONFIG_THOR_FUNCTION) += thor.o -obj-$(CONFIG_CMD_USB_MASS_STORAGE) += ums.o obj-$(CONFIG_MISC_COMMON) += misc.o ifndef CONFIG_SPL_BUILD diff --git a/board/samsung/common/misc.c b/board/samsung/common/misc.c index 3ff4289780..03106fdb9f 100644 --- a/board/samsung/common/misc.c +++ b/board/samsung/common/misc.c @@ -116,12 +116,14 @@ static int check_keys(void) * 4 BOOT_MODE_EXIT */ static char * -mode_name[BOOT_MODE_EXIT + 1] = { - "DEVICE", - "THOR", - "UMS", - "DFU", - "EXIT" +mode_name[BOOT_MODE_EXIT + 1][2] = { + {"DEVICE", ""}, + {"THOR", "thor"}, + {"UMS", "ums"}, + {"DFU", "dfu"}, + {"GPT", "gpt"}, + {"ENV", "env"}, + {"EXIT", ""}, }; static char * @@ -130,18 +132,20 @@ mode_info[BOOT_MODE_EXIT + 1] = { "downloader", "mass storage", "firmware update", + "restore", + "default", "and run normal boot" }; -#define MODE_CMD_ARGC 4 - static char * -mode_cmd[BOOT_MODE_EXIT + 1][MODE_CMD_ARGC] = { - {"", "", "", ""}, - {"thor", "0", "mmc", "0"}, - {"ums", "0", "mmc", "0"}, - {"dfu", "0", "mmc", "0"}, - {"", "", "", ""}, +mode_cmd[BOOT_MODE_EXIT + 1] = { + "", + "thor 0 mmc 0", + "ums 0 mmc 0", + "dfu 0 mmc 0", + "gpt write mmc 0 $partitions", + "env default -a; saveenv", + "", }; static void display_board_info(void) @@ -182,11 +186,10 @@ static void display_board_info(void) static int mode_leave_menu(int mode) { char *exit_option; - char *exit_boot = "boot"; + char *exit_reset = "reset"; char *exit_back = "back"; cmd_tbl_t *cmd; int cmd_result; - int cmd_repeatable; int leave; lcd_clear(); @@ -200,31 +203,29 @@ static int mode_leave_menu(int mode) leave = 0; break; default: - cmd = find_cmd(mode_cmd[mode][0]); + cmd = find_cmd(mode_name[mode][1]); if (cmd) { - printf("Enter: %s %s\n", mode_name[mode], + printf("Enter: %s %s\n", mode_name[mode][0], mode_info[mode]); - lcd_printf("\n\n\t%s %s\n", mode_name[mode], + lcd_printf("\n\n\t%s %s\n", mode_name[mode][0], mode_info[mode]); lcd_puts("\n\tDo not turn off device before finish!\n"); - cmd_result = cmd_process(0, MODE_CMD_ARGC, - *(mode_cmd + mode), - &cmd_repeatable, NULL); + cmd_result = run_command(mode_cmd[mode], 0); if (cmd_result == CMD_RET_SUCCESS) { printf("Command finished\n"); lcd_clear(); lcd_printf("\n\n\t%s finished\n", - mode_name[mode]); + mode_name[mode][0]); - exit_option = exit_boot; + exit_option = exit_reset; leave = 1; } else { printf("Command error\n"); lcd_clear(); lcd_printf("\n\n\t%s command error\n", - mode_name[mode]); + mode_name[mode][0]); exit_option = exit_back; leave = 0; @@ -260,11 +261,11 @@ static void display_download_menu(int mode) selection[mode] = "[=>]"; lcd_clear(); - lcd_printf("\n\t\tDownload Mode Menu\n"); + lcd_printf("\n\n\t\tDownload Mode Menu\n\n"); for (i = 0; i <= BOOT_MODE_EXIT; i++) lcd_printf("\t%s %s - %s\n\n", selection[i], - mode_name[i], + mode_name[i][0], mode_info[i]); } @@ -273,10 +274,38 @@ static void download_menu(void) int mode = 0; int last_mode = 0; int run; - int key; + int key = 0; + int timeout = 15; /* sec */ + int i; display_download_menu(mode); + lcd_puts("\n"); + + /* Start count if no key is pressed */ + while (check_keys()) + continue; + + while (timeout--) { + lcd_printf("\r\tNormal boot will start in: %2.d seconds.", + timeout); + + /* about 1000 ms in for loop */ + for (i = 0; i < 10; i++) { + mdelay(100); + key = check_keys(); + if (key) + break; + } + if (key) + break; + } + + if (!key) { + lcd_clear(); + return; + } + while (1) { run = 0; @@ -284,7 +313,7 @@ static void download_menu(void) display_download_menu(mode); last_mode = mode; - mdelay(100); + mdelay(200); key = check_keys(); switch (key) { @@ -305,7 +334,7 @@ static void download_menu(void) if (run) { if (mode_leave_menu(mode)) - break; + run_command("reset", 0); display_download_menu(mode); } @@ -314,45 +343,6 @@ static void download_menu(void) lcd_clear(); } -static void display_mode_info(void) -{ - lcd_position_cursor(4, 4); - lcd_printf("%s\n", U_BOOT_VERSION); - lcd_puts("\nDownload Mode Menu\n"); -#ifdef CONFIG_SYS_BOARD - lcd_printf("Board name: %s\n", CONFIG_SYS_BOARD); -#endif - lcd_printf("Press POWER KEY to display MENU options."); -} - -static int boot_menu(void) -{ - int key = 0; - int timeout = 10; - - display_mode_info(); - - while (timeout--) { - lcd_printf("\rNormal boot will start in: %d seconds.", timeout); - mdelay(1000); - - key = key_pressed(KEY_POWER); - if (key) - break; - } - - lcd_clear(); - - /* If PWR pressed - show download menu */ - if (key) { - printf("Power pressed - go to download menu\n"); - download_menu(); - printf("Download mode exit.\n"); - } - - return 0; -} - void check_boot_mode(void) { int pwr_key; @@ -365,7 +355,7 @@ void check_boot_mode(void) power_key_pressed(KEY_PWR_INTERRUPT_REG); if (key_pressed(KEY_VOLUMEUP)) - boot_menu(); + download_menu(); else if (key_pressed(KEY_VOLUMEDOWN)) mode_leave_menu(BOOT_MODE_THOR); } diff --git a/board/samsung/common/ums.c b/board/samsung/common/ums.c deleted file mode 100644 index cebabe920a..0000000000 --- a/board/samsung/common/ums.c +++ /dev/null @@ -1,74 +0,0 @@ -/* - * Copyright (C) 2013 Samsung Electronics - * Lukasz Majewski <l.majewski@samsung.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <usb_mass_storage.h> -#include <part.h> - -static int ums_read_sector(struct ums *ums_dev, - ulong start, lbaint_t blkcnt, void *buf) -{ - block_dev_desc_t *block_dev = &ums_dev->mmc->block_dev; - lbaint_t blkstart = start + ums_dev->start_sector; - int dev_num = block_dev->dev; - - return block_dev->block_read(dev_num, blkstart, blkcnt, buf); -} - -static int ums_write_sector(struct ums *ums_dev, - ulong start, lbaint_t blkcnt, const void *buf) -{ - block_dev_desc_t *block_dev = &ums_dev->mmc->block_dev; - lbaint_t blkstart = start + ums_dev->start_sector; - int dev_num = block_dev->dev; - - return block_dev->block_write(dev_num, blkstart, blkcnt, buf); -} - -static struct ums ums_dev = { - .read_sector = ums_read_sector, - .write_sector = ums_write_sector, - .name = "UMS disk", -}; - -static struct ums *ums_disk_init(struct mmc *mmc) -{ - uint64_t mmc_end_sector = mmc->capacity / SECTOR_SIZE; - uint64_t ums_end_sector = UMS_NUM_SECTORS + UMS_START_SECTOR; - - if (!mmc_end_sector) { - error("MMC capacity is not valid"); - return NULL; - } - - ums_dev.mmc = mmc; - - if (ums_end_sector <= mmc_end_sector) { - ums_dev.start_sector = UMS_START_SECTOR; - if (UMS_NUM_SECTORS) - ums_dev.num_sectors = UMS_NUM_SECTORS; - else - ums_dev.num_sectors = mmc_end_sector - UMS_START_SECTOR; - } else { - ums_dev.num_sectors = mmc_end_sector; - puts("UMS: defined bad disk parameters. Using default.\n"); - } - - printf("UMS: disk start sector: %#x, count: %#x\n", - ums_dev.start_sector, ums_dev.num_sectors); - - return &ums_dev; -} - -struct ums *ums_init(unsigned int dev_num) -{ - struct mmc *mmc = find_mmc_device(dev_num); - - if (!mmc || mmc_init(mmc)) - return NULL; - return ums_disk_init(mmc); -} diff --git a/board/samsung/goni/goni.c b/board/samsung/goni/goni.c index 61b9ece038..4cea63b813 100644 --- a/board/samsung/goni/goni.c +++ b/board/samsung/goni/goni.c @@ -17,8 +17,6 @@ DECLARE_GLOBAL_DATA_PTR; -static struct s5pc110_gpio *s5pc110_gpio; - u32 get_board_rev(void) { return 0; @@ -27,8 +25,6 @@ u32 get_board_rev(void) int board_init(void) { /* Set Initial global variables */ - s5pc110_gpio = (struct s5pc110_gpio *)S5PC110_GPIO_BASE; - gd->bd->bi_arch_number = MACH_TYPE_GONI; gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; @@ -82,7 +78,7 @@ int board_mmc_init(bd_t *bis) int i, ret, ret_sd = 0; /* MASSMEMORY_EN: XMSMDATA7: GPJ2[7] output high */ - s5p_gpio_direction_output(&s5pc110_gpio->j2, 7, 1); + gpio_direction_output(S5PC110_GPIO_J27, 1); /* * MMC0 GPIO @@ -91,15 +87,15 @@ int board_mmc_init(bd_t *bis) * GPG0[2] SD_0_CDn -> Not used * GPG0[3:6] SD_0_DATA[0:3] */ - for (i = 0; i < 7; i++) { - if (i == 2) + for (i = S5PC110_GPIO_G00; i < S5PC110_GPIO_G07; i++) { + if (i == S5PC110_GPIO_G02) continue; /* GPG0[0:6] special function 2 */ - s5p_gpio_cfg_pin(&s5pc110_gpio->g0, i, 0x2); + gpio_cfg_pin(i, 0x2); /* GPG0[0:6] pull disable */ - s5p_gpio_set_pull(&s5pc110_gpio->g0, i, GPIO_PULL_NONE); + gpio_set_pull(i, S5P_GPIO_PULL_NONE); /* GPG0[0:6] drv 4x */ - s5p_gpio_set_drv(&s5pc110_gpio->g0, i, GPIO_DRV_4X); + gpio_set_drv(i, S5P_GPIO_DRV_4X); } ret = s5p_mmc_init(0, 4); @@ -110,20 +106,20 @@ int board_mmc_init(bd_t *bis) * SD card (T_FLASH) detect and init * T_FLASH_DETECT: EINT28: GPH3[4] input mode */ - s5p_gpio_cfg_pin(&s5pc110_gpio->h3, 4, GPIO_INPUT); - s5p_gpio_set_pull(&s5pc110_gpio->h3, 4, GPIO_PULL_UP); + gpio_cfg_pin(S5PC110_GPIO_H34, S5P_GPIO_INPUT); + gpio_set_pull(S5PC110_GPIO_H34, S5P_GPIO_PULL_UP); - if (!s5p_gpio_get_value(&s5pc110_gpio->h3, 4)) { - for (i = 0; i < 7; i++) { - if (i == 2) + if (!gpio_get_value(S5PC110_GPIO_H34)) { + for (i = S5PC110_GPIO_G20; i < S5PC110_GPIO_G27; i++) { + if (i == S5PC110_GPIO_G22) continue; /* GPG2[0:6] special function 2 */ - s5p_gpio_cfg_pin(&s5pc110_gpio->g2, i, 0x2); + gpio_cfg_pin(i, 0x2); /* GPG2[0:6] pull disable */ - s5p_gpio_set_pull(&s5pc110_gpio->g2, i, GPIO_PULL_NONE); + gpio_set_pull(i, S5P_GPIO_PULL_NONE); /* GPG2[0:6] drv 4x */ - s5p_gpio_set_drv(&s5pc110_gpio->g2, i, GPIO_DRV_4X); + gpio_set_drv(i, S5P_GPIO_DRV_4X); } ret_sd = s5p_mmc_init(2, 4); diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c index 379a45cc23..58821c41a4 100644 --- a/board/samsung/smdk5250/exynos5-dt.c +++ b/board/samsung/smdk5250/exynos5-dt.c @@ -27,12 +27,9 @@ DECLARE_GLOBAL_DATA_PTR; #ifdef CONFIG_SOUND_MAX98095 static void board_enable_audio_codec(void) { - struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *) - samsung_get_base_gpio_part1(); - /* Enable MAX98095 Codec */ - s5p_gpio_direction_output(&gpio1->x1, 7, 1); - s5p_gpio_set_pull(&gpio1->x1, 7, GPIO_PULL_NONE); + gpio_direction_output(EXYNOS5_GPIO_X17, 1); + gpio_set_pull(EXYNOS5_GPIO_X17, S5P_GPIO_PULL_NONE); } #endif @@ -47,19 +44,16 @@ int exynos_init(void) #ifdef CONFIG_LCD void exynos_cfg_lcd_gpio(void) { - struct exynos5_gpio_part1 *gpio1 = - (struct exynos5_gpio_part1 *)samsung_get_base_gpio_part1(); - /* For Backlight */ - s5p_gpio_cfg_pin(&gpio1->b2, 0, GPIO_OUTPUT); - s5p_gpio_set_value(&gpio1->b2, 0, 1); + gpio_cfg_pin(EXYNOS5_GPIO_B20, S5P_GPIO_OUTPUT); + gpio_set_value(EXYNOS5_GPIO_B20, 1); /* LCD power on */ - s5p_gpio_cfg_pin(&gpio1->x1, 5, GPIO_OUTPUT); - s5p_gpio_set_value(&gpio1->x1, 5, 1); + gpio_cfg_pin(EXYNOS5_GPIO_X15, S5P_GPIO_OUTPUT); + gpio_set_value(EXYNOS5_GPIO_X15, 1); /* Set Hotplug detect for DP */ - s5p_gpio_cfg_pin(&gpio1->x0, 7, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5_GPIO_X07, S5P_GPIO_FUNC(0x3)); } void exynos_set_dp_phy(unsigned int onoff) diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c index 28a6d9e718..014b7bdf89 100644 --- a/board/samsung/smdk5250/smdk5250.c +++ b/board/samsung/smdk5250/smdk5250.c @@ -29,12 +29,9 @@ DECLARE_GLOBAL_DATA_PTR; #ifdef CONFIG_SOUND_MAX98095 static void board_enable_audio_codec(void) { - struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *) - samsung_get_base_gpio_part1(); - /* Enable MAX98095 Codec */ - s5p_gpio_direction_output(&gpio1->x1, 7, 1); - s5p_gpio_set_pull(&gpio1->x1, 7, GPIO_PULL_NONE); + gpio_direction_output(EXYNOS5_GPIO_X17, 1); + gpio_set_pull(EXYNOS5_GPIO_X17, S5P_GPIO_PULL_NONE); } #endif @@ -275,19 +272,17 @@ int exynos_power_init(void) #ifdef CONFIG_LCD void exynos_cfg_lcd_gpio(void) { - struct exynos5_gpio_part1 *gpio1 = - (struct exynos5_gpio_part1 *) samsung_get_base_gpio_part1(); /* For Backlight */ - s5p_gpio_cfg_pin(&gpio1->b2, 0, GPIO_OUTPUT); - s5p_gpio_set_value(&gpio1->b2, 0, 1); + gpio_cfg_pin(EXYNOS5_GPIO_B20, S5P_GPIO_OUTPUT); + gpio_set_value(EXYNOS5_GPIO_B20, 1); /* LCD power on */ - s5p_gpio_cfg_pin(&gpio1->x1, 5, GPIO_OUTPUT); - s5p_gpio_set_value(&gpio1->x1, 5, 1); + gpio_cfg_pin(EXYNOS5_GPIO_X15, S5P_GPIO_OUTPUT); + gpio_set_value(EXYNOS5_GPIO_X15, 1); /* Set Hotplug detect for DP */ - s5p_gpio_cfg_pin(&gpio1->x0, 7, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5_GPIO_X07, S5P_GPIO_FUNC(0x3)); } void exynos_set_dp_phy(unsigned int onoff) diff --git a/board/samsung/smdk5420/smdk5420.c b/board/samsung/smdk5420/smdk5420.c index e4606ecd2a..9207522953 100644 --- a/board/samsung/smdk5420/smdk5420.c +++ b/board/samsung/smdk5420/smdk5420.c @@ -21,11 +21,8 @@ DECLARE_GLOBAL_DATA_PTR; #ifdef CONFIG_USB_EHCI_EXYNOS static int board_usb_vbus_init(void) { - struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *) - samsung_get_base_gpio_part1(); - /* Enable VBUS power switch */ - s5p_gpio_direction_output(&gpio1->x2, 6, 1); + gpio_direction_output(EXYNOS5420_GPIO_X26, 1); /* VBUS turn ON time */ mdelay(3); @@ -49,15 +46,15 @@ void cfg_lcd_gpio(void) (struct exynos5_gpio_part1 *)samsung_get_base_gpio_part1(); /* For Backlight */ - s5p_gpio_cfg_pin(&gpio1->b2, 0, GPIO_OUTPUT); - s5p_gpio_set_value(&gpio1->b2, 0, 1); + gpio_cfg_pin(EXYNOS5420_GPIO_B20, S5P_GPIO_OUTPUT); + gpio_set_value(EXYNOS5420_GPIO_B20, 1); /* LCD power on */ - s5p_gpio_cfg_pin(&gpio1->x1, 5, GPIO_OUTPUT); - s5p_gpio_set_value(&gpio1->x1, 5, 1); + gpio_cfg_pin(EXYNOS5420_GPIO_X15, S5P_GPIO_OUTPUT); + gpio_set_value(EXYNOS5420_GPIO_X15, 1); /* Set Hotplug detect for DP */ - s5p_gpio_cfg_pin(&gpio1->x0, 7, GPIO_FUNC(0x3)); + gpio_cfg_pin(EXYNOS5420_GPIO_X07, S5P_GPIO_FUNC(0x3)); } vidinfo_t panel_info = { diff --git a/board/samsung/smdkc100/smdkc100.c b/board/samsung/smdkc100/smdkc100.c index 860c851b25..e009564a59 100644 --- a/board/samsung/smdkc100/smdkc100.c +++ b/board/samsung/smdkc100/smdkc100.c @@ -21,11 +21,8 @@ static void smc9115_pre_init(void) { u32 smc_bw_conf, smc_bc_conf; - struct s5pc100_gpio *const gpio = - (struct s5pc100_gpio *)samsung_get_base_gpio(); - /* gpio configuration GPK0CON */ - s5p_gpio_cfg_pin(&gpio->k0, CONFIG_ENV_SROM_BANK, GPIO_FUNC(2)); + gpio_cfg_pin(S5PC100_GPIO_K00 + CONFIG_ENV_SROM_BANK, S5P_GPIO_FUNC(2)); /* Ethernet needs bus width of 16 bits */ smc_bw_conf = SMC_DATA16_WIDTH(CONFIG_ENV_SROM_BANK); diff --git a/board/samsung/smdkv310/smdkv310.c b/board/samsung/smdkv310/smdkv310.c index 81a306082d..8eca358981 100644 --- a/board/samsung/smdkv310/smdkv310.c +++ b/board/samsung/smdkv310/smdkv310.c @@ -15,15 +15,13 @@ #include <asm/arch/sromc.h> DECLARE_GLOBAL_DATA_PTR; -struct exynos4_gpio_part1 *gpio1; -struct exynos4_gpio_part2 *gpio2; static void smc9115_pre_init(void) { u32 smc_bw_conf, smc_bc_conf; /* gpio configuration GPK0CON */ - s5p_gpio_cfg_pin(&gpio2->y0, CONFIG_ENV_SROM_BANK, GPIO_FUNC(2)); + gpio_cfg_pin(EXYNOS4_GPIO_Y00 + CONFIG_ENV_SROM_BANK, S5P_GPIO_FUNC(2)); /* Ethernet needs bus width of 16 bits */ smc_bw_conf = SROMC_DATA16_WIDTH(CONFIG_ENV_SROM_BANK); @@ -38,9 +36,6 @@ static void smc9115_pre_init(void) int board_init(void) { - gpio1 = (struct exynos4_gpio_part1 *) EXYNOS4_GPIO_PART1_BASE; - gpio2 = (struct exynos4_gpio_part2 *) EXYNOS4_GPIO_PART2_BASE; - smc9115_pre_init(); gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL); @@ -103,21 +98,21 @@ int board_mmc_init(bd_t *bis) * GPK2[2] SD_2_CDn * GPK2[3:6] SD_2_DATA[0:3](2) */ - for (i = 0; i < 7; i++) { + for (i = EXYNOS4_GPIO_K20; i < EXYNOS4_GPIO_K27; i++) { /* GPK2[0:6] special function 2 */ - s5p_gpio_cfg_pin(&gpio2->k2, i, GPIO_FUNC(0x2)); + gpio_cfg_pin(i, S5P_GPIO_FUNC(0x2)); /* GPK2[0:6] drv 4x */ - s5p_gpio_set_drv(&gpio2->k2, i, GPIO_DRV_4X); + gpio_set_drv(i, S5P_GPIO_DRV_4X); /* GPK2[0:1] pull disable */ - if (i == 0 || i == 1) { - s5p_gpio_set_pull(&gpio2->k2, i, GPIO_PULL_NONE); + if (i == EXYNOS4_GPIO_K20 || i == EXYNOS4_GPIO_K21) { + gpio_set_pull(i, S5P_GPIO_PULL_NONE); continue; } /* GPK2[2:6] pull up */ - s5p_gpio_set_pull(&gpio2->k2, i, GPIO_PULL_UP); + gpio_set_pull(i, S5P_GPIO_PULL_UP); } err = s5p_mmc_init(2, 4); return err; diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c index ab0ad1d650..fec72d4c54 100644 --- a/board/samsung/trats/trats.c +++ b/board/samsung/trats/trats.c @@ -54,8 +54,6 @@ int exynos_init(void) void i2c_init_board(void) { int err; - struct exynos4_gpio_part2 *gpio2 = - (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); /* I2C_5 -> PMIC */ err = exynos_pinmux_config(PERIPH_ID_I2C5, PINMUX_FLAG_NONE); @@ -65,8 +63,8 @@ void i2c_init_board(void) } /* I2C_8 -> FG */ - s5p_gpio_direction_output(&gpio2->y4, 0, 1); - s5p_gpio_direction_output(&gpio2->y4, 1, 1); + gpio_direction_output(EXYNOS4_GPIO_Y40, 1); + gpio_direction_output(EXYNOS4_GPIO_Y41, 1); } static void trats_low_power_mode(void) @@ -347,21 +345,19 @@ int exynos_power_init(void) static unsigned int get_hw_revision(void) { - struct exynos4_gpio_part1 *gpio = - (struct exynos4_gpio_part1 *)samsung_get_base_gpio_part1(); int hwrev = 0; int i; /* hw_rev[3:0] == GPE1[3:0] */ - for (i = 0; i < 4; i++) { - s5p_gpio_cfg_pin(&gpio->e1, i, GPIO_INPUT); - s5p_gpio_set_pull(&gpio->e1, i, GPIO_PULL_NONE); + for (i = EXYNOS4_GPIO_E10; i < EXYNOS4_GPIO_E14; i++) { + gpio_cfg_pin(i, S5P_GPIO_INPUT); + gpio_set_pull(i, S5P_GPIO_PULL_NONE); } udelay(1); for (i = 0; i < 4; i++) - hwrev |= (s5p_gpio_get_value(&gpio->e1, i) << i); + hwrev |= (gpio_get_value(EXYNOS4_GPIO_E10 + i) << i); debug("hwrev 0x%x\n", hwrev); @@ -442,11 +438,8 @@ int g_dnl_board_usb_cable_connected(void) static void pmic_reset(void) { - struct exynos4_gpio_part2 *gpio = - (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); - - s5p_gpio_direction_output(&gpio->x0, 7, 1); - s5p_gpio_set_pull(&gpio->x2, 7, GPIO_PULL_NONE); + gpio_direction_output(EXYNOS4_GPIO_X07, 1); + gpio_set_pull(EXYNOS4_GPIO_X27, S5P_GPIO_PULL_NONE); } static void board_clock_init(void) @@ -523,12 +516,9 @@ static void board_power_init(void) static void exynos_uart_init(void) { - struct exynos4_gpio_part2 *gpio2 = - (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); - /* UART_SEL GPY4[7] (part2) at EXYNOS4 */ - s5p_gpio_set_pull(&gpio2->y4, 7, GPIO_PULL_UP); - s5p_gpio_direction_output(&gpio2->y4, 7, 1); + gpio_set_pull(EXYNOS4_GPIO_Y47, S5P_GPIO_PULL_UP); + gpio_direction_output(EXYNOS4_GPIO_Y47, 1); } int exynos_early_init_f(void) @@ -544,14 +534,11 @@ int exynos_early_init_f(void) void exynos_reset_lcd(void) { - struct exynos4_gpio_part2 *gpio2 = - (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); - - s5p_gpio_direction_output(&gpio2->y4, 5, 1); + gpio_direction_output(EXYNOS4_GPIO_Y45, 1); udelay(10000); - s5p_gpio_direction_output(&gpio2->y4, 5, 0); + gpio_direction_output(EXYNOS4_GPIO_Y45, 0); udelay(10000); - s5p_gpio_direction_output(&gpio2->y4, 5, 1); + gpio_direction_output(EXYNOS4_GPIO_Y45, 1); } int lcd_power(void) diff --git a/board/samsung/trats2/trats2.c b/board/samsung/trats2/trats2.c index 47095252a7..e4987ce8b4 100644 --- a/board/samsung/trats2/trats2.c +++ b/board/samsung/trats2/trats2.c @@ -25,9 +25,6 @@ DECLARE_GLOBAL_DATA_PTR; -static struct exynos4x12_gpio_part1 *gpio1; -static struct exynos4x12_gpio_part2 *gpio2; - static unsigned int board_rev = -1; static inline u32 get_model_rev(void); @@ -37,26 +34,24 @@ static void check_hw_revision(void) int modelrev = 0; int i; - gpio2 = (struct exynos4x12_gpio_part2 *)samsung_get_base_gpio_part2(); - /* * GPM1[1:0]: MODEL_REV[1:0] * Don't set as pull-none for these N/C pin. * TRM say that it may cause unexcepted state and leakage current. * and pull-none is only for output function. */ - for (i = 0; i < 2; i++) - s5p_gpio_cfg_pin(&gpio2->m1, i, GPIO_INPUT); + for (i = EXYNOS4X12_GPIO_M10; i < EXYNOS4X12_GPIO_M12; i++) + gpio_cfg_pin(i, S5P_GPIO_INPUT); /* GPM1[5:2]: HW_REV[3:0] */ - for (i = 2; i < 6; i++) { - s5p_gpio_cfg_pin(&gpio2->m1, i, GPIO_INPUT); - s5p_gpio_set_pull(&gpio2->m1, i, GPIO_PULL_NONE); + for (i = EXYNOS4X12_GPIO_M12; i < EXYNOS4X12_GPIO_M16; i++) { + gpio_cfg_pin(i, S5P_GPIO_INPUT); + gpio_set_pull(i, S5P_GPIO_PULL_NONE); } /* GPM1[1:0]: MODEL_REV[1:0] */ for (i = 0; i < 2; i++) - modelrev |= (s5p_gpio_get_value(&gpio2->m1, i) << i); + modelrev |= (gpio_get_value(EXYNOS4X12_GPIO_M10 + i) << i); /* board_rev[15:8] = model */ board_rev = modelrev << 8; @@ -74,26 +69,24 @@ static inline u32 get_model_rev(void) static void board_external_gpio_init(void) { - gpio2 = (struct exynos4x12_gpio_part2 *)samsung_get_base_gpio_part2(); - /* * some pins which in alive block are connected with external pull-up * but it's default setting is pull-down. * if that pin set as input then that floated */ - s5p_gpio_set_pull(&gpio2->x0, 2, GPIO_PULL_NONE); /* PS_ALS_INT */ - s5p_gpio_set_pull(&gpio2->x0, 4, GPIO_PULL_NONE); /* TSP_nINT */ - s5p_gpio_set_pull(&gpio2->x0, 7, GPIO_PULL_NONE); /* AP_PMIC_IRQ*/ - s5p_gpio_set_pull(&gpio2->x1, 5, GPIO_PULL_NONE); /* IF_PMIC_IRQ*/ - s5p_gpio_set_pull(&gpio2->x2, 0, GPIO_PULL_NONE); /* VOL_UP */ - s5p_gpio_set_pull(&gpio2->x2, 1, GPIO_PULL_NONE); /* VOL_DOWN */ - s5p_gpio_set_pull(&gpio2->x2, 3, GPIO_PULL_NONE); /* FUEL_ALERT */ - s5p_gpio_set_pull(&gpio2->x2, 4, GPIO_PULL_NONE); /* ADC_INT */ - s5p_gpio_set_pull(&gpio2->x2, 7, GPIO_PULL_NONE); /* nPOWER */ - s5p_gpio_set_pull(&gpio2->x3, 0, GPIO_PULL_NONE); /* WPC_INT */ - s5p_gpio_set_pull(&gpio2->x3, 5, GPIO_PULL_NONE); /* OK_KEY */ - s5p_gpio_set_pull(&gpio2->x3, 7, GPIO_PULL_NONE); /* HDMI_HPD */ + gpio_set_pull(EXYNOS4X12_GPIO_X02, S5P_GPIO_PULL_NONE); /* PS_ALS_INT */ + gpio_set_pull(EXYNOS4X12_GPIO_X04, S5P_GPIO_PULL_NONE); /* TSP_nINT */ + gpio_set_pull(EXYNOS4X12_GPIO_X07, S5P_GPIO_PULL_NONE); /* AP_PMIC_IRQ*/ + gpio_set_pull(EXYNOS4X12_GPIO_X15, S5P_GPIO_PULL_NONE); /* IF_PMIC_IRQ*/ + gpio_set_pull(EXYNOS4X12_GPIO_X20, S5P_GPIO_PULL_NONE); /* VOL_UP */ + gpio_set_pull(EXYNOS4X12_GPIO_X21, S5P_GPIO_PULL_NONE); /* VOL_DOWN */ + gpio_set_pull(EXYNOS4X12_GPIO_X23, S5P_GPIO_PULL_NONE); /* FUEL_ALERT */ + gpio_set_pull(EXYNOS4X12_GPIO_X24, S5P_GPIO_PULL_NONE); /* ADC_INT */ + gpio_set_pull(EXYNOS4X12_GPIO_X27, S5P_GPIO_PULL_NONE); /* nPOWER */ + gpio_set_pull(EXYNOS4X12_GPIO_X30, S5P_GPIO_PULL_NONE); /* WPC_INT */ + gpio_set_pull(EXYNOS4X12_GPIO_X35, S5P_GPIO_PULL_NONE); /* OK_KEY */ + gpio_set_pull(EXYNOS4X12_GPIO_X37, S5P_GPIO_PULL_NONE); /* HDMI_HPD */ } #ifdef CONFIG_SYS_I2C_INIT_BOARD @@ -101,9 +94,6 @@ static void board_init_i2c(void) { int err; - gpio1 = (struct exynos4x12_gpio_part1 *)samsung_get_base_gpio_part1(); - gpio2 = (struct exynos4x12_gpio_part2 *)samsung_get_base_gpio_part2(); - /* I2C_7 */ err = exynos_pinmux_config(PERIPH_ID_I2C7, PINMUX_FLAG_NONE); if (err) { @@ -112,12 +102,12 @@ static void board_init_i2c(void) } /* I2C_8 */ - s5p_gpio_direction_output(&gpio1->f1, 4, 1); - s5p_gpio_direction_output(&gpio1->f1, 5, 1); + gpio_direction_output(EXYNOS4X12_GPIO_F14, 1); + gpio_direction_output(EXYNOS4X12_GPIO_F15, 1); /* I2C_9 */ - s5p_gpio_direction_output(&gpio2->m2, 1, 1); - s5p_gpio_direction_output(&gpio2->m2, 0, 1); + gpio_direction_output(EXYNOS4X12_GPIO_M21, 1); + gpio_direction_output(EXYNOS4X12_GPIO_M20, 1); } #endif @@ -125,17 +115,17 @@ static void board_init_i2c(void) int get_soft_i2c_scl_pin(void) { if (I2C_ADAP_HWNR) - return exynos4x12_gpio_get(2, m2, 1); /* I2C9 */ + return EXYNOS4X12_GPIO_M21; /* I2C9 */ else - return exynos4x12_gpio_get(1, f1, 4); /* I2C8 */ + return EXYNOS4X12_GPIO_F14; /* I2C8 */ } int get_soft_i2c_sda_pin(void) { if (I2C_ADAP_HWNR) - return exynos4x12_gpio_get(2, m2, 0); /* I2C9 */ + return EXYNOS4X12_GPIO_M20; /* I2C9 */ else - return exynos4x12_gpio_get(1, f1, 5); /* I2C8 */ + return EXYNOS4X12_GPIO_F15; /* I2C8 */ } #endif @@ -396,11 +386,9 @@ void exynos_lcd_power_on(void) { struct pmic *p = pmic_get("MAX77686_PMIC"); - gpio1 = (struct exynos4x12_gpio_part1 *)samsung_get_base_gpio_part1(); - /* LCD_2.2V_EN: GPC0[1] */ - s5p_gpio_set_pull(&gpio1->c0, 1, GPIO_PULL_UP); - s5p_gpio_direction_output(&gpio1->c0, 1, 1); + gpio_set_pull(EXYNOS4X12_GPIO_C01, S5P_GPIO_PULL_UP); + gpio_direction_output(EXYNOS4X12_GPIO_C01, 1); /* LDO25 VCC_3.1V_LCD */ pmic_probe(p); @@ -410,12 +398,10 @@ void exynos_lcd_power_on(void) void exynos_reset_lcd(void) { - gpio1 = (struct exynos4x12_gpio_part1 *)samsung_get_base_gpio_part1(); - /* reset lcd */ - s5p_gpio_direction_output(&gpio1->f2, 1, 0); + gpio_direction_output(EXYNOS4X12_GPIO_F21, 0); udelay(10); - s5p_gpio_set_value(&gpio1->f2, 1, 1); + gpio_set_value(EXYNOS4X12_GPIO_F21, 1); } void exynos_lcd_misc_init(vidinfo_t *vid) diff --git a/board/samsung/universal_c210/universal.c b/board/samsung/universal_c210/universal.c index 8e49195fe1..47e7f538d6 100644 --- a/board/samsung/universal_c210/universal.c +++ b/board/samsung/universal_c210/universal.c @@ -27,8 +27,6 @@ DECLARE_GLOBAL_DATA_PTR; -struct exynos4_gpio_part1 *gpio1; -struct exynos4_gpio_part2 *gpio2; unsigned int board_rev; u32 get_board_rev(void) @@ -305,35 +303,35 @@ void exynos_cfg_lcd_gpio(void) for (i = 0; i < 8; i++) { /* set GPF0,1,2[0:7] for RGB Interface and Data lines (32bit) */ - s5p_gpio_cfg_pin(&gpio1->f0, i, GPIO_FUNC(2)); - s5p_gpio_cfg_pin(&gpio1->f1, i, GPIO_FUNC(2)); - s5p_gpio_cfg_pin(&gpio1->f2, i, GPIO_FUNC(2)); + gpio_cfg_pin(EXYNOS4_GPIO_F00 + i, S5P_GPIO_FUNC(2)); + gpio_cfg_pin(EXYNOS4_GPIO_F10 + i, S5P_GPIO_FUNC(2)); + gpio_cfg_pin(EXYNOS4_GPIO_F20 + i, S5P_GPIO_FUNC(2)); /* pull-up/down disable */ - s5p_gpio_set_pull(&gpio1->f0, i, GPIO_PULL_NONE); - s5p_gpio_set_pull(&gpio1->f1, i, GPIO_PULL_NONE); - s5p_gpio_set_pull(&gpio1->f2, i, GPIO_PULL_NONE); + gpio_set_pull(EXYNOS4_GPIO_F00 + i, S5P_GPIO_PULL_NONE); + gpio_set_pull(EXYNOS4_GPIO_F10 + i, S5P_GPIO_PULL_NONE); + gpio_set_pull(EXYNOS4_GPIO_F20 + i, S5P_GPIO_PULL_NONE); /* drive strength to max (24bit) */ - s5p_gpio_set_drv(&gpio1->f0, i, GPIO_DRV_4X); - s5p_gpio_set_rate(&gpio1->f0, i, GPIO_DRV_SLOW); - s5p_gpio_set_drv(&gpio1->f1, i, GPIO_DRV_4X); - s5p_gpio_set_rate(&gpio1->f1, i, GPIO_DRV_SLOW); - s5p_gpio_set_drv(&gpio1->f2, i, GPIO_DRV_4X); - s5p_gpio_set_rate(&gpio1->f0, i, GPIO_DRV_SLOW); + gpio_set_drv(EXYNOS4_GPIO_F00 + i, S5P_GPIO_DRV_4X); + gpio_set_rate(EXYNOS4_GPIO_F00 + i, S5P_GPIO_DRV_SLOW); + gpio_set_drv(EXYNOS4_GPIO_F10 + i, S5P_GPIO_DRV_4X); + gpio_set_rate(EXYNOS4_GPIO_F10 + i, S5P_GPIO_DRV_SLOW); + gpio_set_drv(EXYNOS4_GPIO_F20 + i, S5P_GPIO_DRV_4X); + gpio_set_rate(EXYNOS4_GPIO_F00 + i, S5P_GPIO_DRV_SLOW); } - for (i = 0; i < f3_end; i++) { + for (i = EXYNOS4_GPIO_F30; i < (EXYNOS4_GPIO_F30 + f3_end); i++) { /* set GPF3[0:3] for RGB Interface and Data lines (32bit) */ - s5p_gpio_cfg_pin(&gpio1->f3, i, GPIO_FUNC(2)); + gpio_cfg_pin(i, S5P_GPIO_FUNC(2)); /* pull-up/down disable */ - s5p_gpio_set_pull(&gpio1->f3, i, GPIO_PULL_NONE); + gpio_set_pull(i, S5P_GPIO_PULL_NONE); /* drive strength to max (24bit) */ - s5p_gpio_set_drv(&gpio1->f3, i, GPIO_DRV_4X); - s5p_gpio_set_rate(&gpio1->f3, i, GPIO_DRV_SLOW); + gpio_set_drv(i, S5P_GPIO_DRV_4X); + gpio_set_rate(i, S5P_GPIO_DRV_SLOW); } /* gpio pad configuration for LCD reset. */ - s5p_gpio_cfg_pin(&gpio2->y4, 5, GPIO_OUTPUT); + gpio_cfg_pin(EXYNOS4_GPIO_Y45, S5P_GPIO_OUTPUT); spi_init(); } @@ -345,11 +343,11 @@ int mipi_power(void) void exynos_reset_lcd(void) { - s5p_gpio_set_value(&gpio2->y4, 5, 1); + gpio_set_value(EXYNOS4_GPIO_Y45, 1); udelay(10000); - s5p_gpio_set_value(&gpio2->y4, 5, 0); + gpio_set_value(EXYNOS4_GPIO_Y45, 0); udelay(10000); - s5p_gpio_set_value(&gpio2->y4, 5, 1); + gpio_set_value(EXYNOS4_GPIO_Y45, 1); udelay(100); } @@ -379,9 +377,6 @@ void exynos_enable_ldo(unsigned int onoff) int exynos_init(void) { - gpio1 = (struct exynos4_gpio_part1 *) EXYNOS4_GPIO_PART1_BASE; - gpio2 = (struct exynos4_gpio_part2 *) EXYNOS4_GPIO_PART2_BASE; - gd->bd->bi_arch_number = MACH_TYPE_UNIVERSAL_C210; switch (get_hwrev()) { @@ -392,7 +387,7 @@ int exynos_init(void) * you should set it HIGH since it removes the inverter */ /* MASSMEMORY_EN: XMDMDATA_6: GPE3[6] */ - s5p_gpio_direction_output(&gpio1->e3, 6, 0); + gpio_direction_output(EXYNOS4_GPIO_E36, 0); break; default: /* @@ -400,7 +395,7 @@ int exynos_init(void) * But set it as HIGH to ensure */ /* MASSMEMORY_EN: XMDMADDR_3: GPE1[3] */ - s5p_gpio_direction_output(&gpio1->e1, 3, 1); + gpio_direction_output(EXYNOS4_GPIO_E13, 1); break; } diff --git a/board/sandbox/Makefile b/board/sandbox/Makefile new file mode 100644 index 0000000000..a0b9880d6e --- /dev/null +++ b/board/sandbox/Makefile @@ -0,0 +1,7 @@ +# +# Copyright (c) 2011 The Chromium OS Authors. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := sandbox.o diff --git a/doc/README.sandbox b/board/sandbox/README.sandbox index 529c447a5b..529c447a5b 100644 --- a/doc/README.sandbox +++ b/board/sandbox/README.sandbox diff --git a/arch/sandbox/lib/sandbox.c b/board/sandbox/sandbox.c index e4d4e021bc..e4d4e021bc 100644 --- a/arch/sandbox/lib/sandbox.c +++ b/board/sandbox/sandbox.c diff --git a/board/siemens/common/board.c b/board/siemens/common/board.c index 7e8731bb3b..2782bcc2a7 100644 --- a/board/siemens/common/board.c +++ b/board/siemens/common/board.c @@ -128,12 +128,6 @@ do_userbutton(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) button = 0; gpio_free(gpio); - if (!button) { - /* LED0 - RED=1: GPIO2_0 2*32 = 64 */ - gpio_request(BOARD_DFU_BUTTON_LED, ""); - gpio_direction_output(BOARD_DFU_BUTTON_LED, 1); - gpio_set_value(BOARD_DFU_BUTTON_LED, 1); - } return button; } @@ -144,6 +138,46 @@ U_BOOT_CMD( "" ); #endif +/* + * This command sets led + * Input - name of led + * value of led + * Returns - 1 if input does not match + * 0 if led was set + */ +static int +do_setled(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + int gpio = 0; + if (argc != 3) + goto exit; +#if defined(BOARD_STATUS_LED) + if (!strcmp(argv[1], "stat")) + gpio = BOARD_STATUS_LED; +#endif +#if defined(BOARD_DFU_BUTTON_LED) + if (!strcmp(argv[1], "dfu")) + gpio = BOARD_DFU_BUTTON_LED; +#endif + /* If argument does not mach exit */ + if (gpio == 0) + goto exit; + gpio_request(gpio, ""); + gpio_direction_output(gpio, 1); + if (!strcmp(argv[2], "1")) + gpio_set_value(gpio, 1); + else + gpio_set_value(gpio, 0); + return 0; +exit: + return 1; +} + +U_BOOT_CMD( + led, CONFIG_SYS_MAXARGS, 2, do_setled, + "Set led on or off", + "dfu val - set dfu led\nled stat val - set status led" +); static int do_usertestwdt(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) diff --git a/board/siemens/dxr2/Makefile b/board/siemens/draco/Makefile index f15993216b..f15993216b 100644 --- a/board/siemens/dxr2/Makefile +++ b/board/siemens/draco/Makefile diff --git a/board/siemens/dxr2/board.c b/board/siemens/draco/board.c index 38ac93d795..9be2e344f8 100644 --- a/board/siemens/dxr2/board.c +++ b/board/siemens/draco/board.c @@ -1,5 +1,5 @@ /* - * Board functions for TI AM335X based dxr2 board + * Board functions for TI AM335X based draco board * (C) Copyright 2013 Siemens Schweiz AG * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. * @@ -37,13 +37,27 @@ DECLARE_GLOBAL_DATA_PTR; #ifdef CONFIG_SPL_BUILD -static struct dxr2_baseboard_id __attribute__((section(".data"))) settings; -/* @303MHz-i0 */ +static struct draco_baseboard_id __attribute__((section(".data"))) settings; + +#if DDR_PLL_FREQ == 303 +/* Default@303MHz-i0 */ +const struct ddr3_data ddr3_default = { + 0x33524444, 0x56312e35, 0x0080, 0x0000, 0x003A, 0x003F, 0x009F, + 0x0079, 0x0888A39B, 0x26247FDA, 0x501F821F, 0x00100206, 0x61A44A32, + 0x0000093B, 0x0000014A, + "default name @303MHz \0", + "default marking \0", +}; +#elif DDR_PLL_FREQ == 400 +/* Default@400MHz-i0 */ const struct ddr3_data ddr3_default = { - 0x33524444, 0x56312e34, 0x0080, 0x0000, 0x0038, 0x003E, 0x00A4, - 0x0075, 0x0888A39B, 0x26247FDA, 0x501F821F, 0x00100206, 0x61A44A32, + 0x33524444, 0x56312e35, 0x0080, 0x0000, 0x0039, 0x0046, 0x00ab, + 0x0080, 0x0AAAA4DB, 0x26307FDA, 0x501F821F, 0x00100207, 0x61A45232, 0x00000618, 0x0000014A, + "default name @400MHz \0", + "default marking \0", }; +#endif static void set_default_ddr3_timings(void) { @@ -53,8 +67,12 @@ static void set_default_ddr3_timings(void) static void print_ddr3_timings(void) { - printf("\n\nDDR3 Timing parameters:\n"); - printf("Diff Eeprom Default\n"); + printf("\nDDR3\n"); + printf("clock:\t\t%d MHz\n", DDR_PLL_FREQ); + printf("device:\t\t%s\n", settings.ddr3.manu_name); + printf("marking:\t%s\n", settings.ddr3.manu_marking); + printf("timing parameters\n"); + printf("diff\teeprom\tdefault\n"); PRINTARGS(magic); PRINTARGS(version); PRINTARGS(ddr3_sratio); @@ -78,9 +96,9 @@ static void print_ddr3_timings(void) static void print_chip_data(void) { - printf("\n"); - printf("Device: '%s'\n", settings.chip.sdevname); - printf("HW version: '%s'\n", settings.chip.shwver); + printf("\nCPU BOARD\n"); + printf("device: \t'%s'\n", settings.chip.sdevname); + printf("hw version: \t'%s'\n", settings.chip.shwver); } #endif /* CONFIG_SPL_BUILD */ @@ -112,20 +130,18 @@ static int read_eeprom(void) printf("Using DDR3 settings from EEPROM\n"); } else { if (ddr3_default.magic != settings.ddr3.magic) - printf("Error: No valid DDR3 data in eeprom.\n"); + printf("Warning: No valid DDR3 data in eeprom.\n"); if (ddr3_default.version != settings.ddr3.version) - printf("Error: DDR3 data version does not match.\n"); + printf("Warning: DDR3 data version does not match.\n"); printf("Using default settings\n"); set_default_ddr3_timings(); } - if (MAGIC_CHIP == settings.chip.magic) { - printf("Valid chip data in eeprom\n"); + if (MAGIC_CHIP == settings.chip.magic) print_chip_data(); - } else { - printf("Error: No chip data in eeprom\n"); - } + else + printf("Warning: No chip data in eeprom\n"); print_ddr3_timings(); #endif @@ -135,48 +151,48 @@ static int read_eeprom(void) #ifdef CONFIG_SPL_BUILD static void board_init_ddr(void) { -struct emif_regs dxr2_ddr3_emif_reg_data = { +struct emif_regs draco_ddr3_emif_reg_data = { .zq_config = 0x50074BE4, }; -struct ddr_data dxr2_ddr3_data = { +struct ddr_data draco_ddr3_data = { }; -struct cmd_control dxr2_ddr3_cmd_ctrl_data = { +struct cmd_control draco_ddr3_cmd_ctrl_data = { }; -struct ctrl_ioregs dxr2_ddr3_ioregs = { +struct ctrl_ioregs draco_ddr3_ioregs = { }; /* pass values from eeprom */ - dxr2_ddr3_emif_reg_data.sdram_tim1 = settings.ddr3.sdram_tim1; - dxr2_ddr3_emif_reg_data.sdram_tim2 = settings.ddr3.sdram_tim2; - dxr2_ddr3_emif_reg_data.sdram_tim3 = settings.ddr3.sdram_tim3; - dxr2_ddr3_emif_reg_data.emif_ddr_phy_ctlr_1 = + draco_ddr3_emif_reg_data.sdram_tim1 = settings.ddr3.sdram_tim1; + draco_ddr3_emif_reg_data.sdram_tim2 = settings.ddr3.sdram_tim2; + draco_ddr3_emif_reg_data.sdram_tim3 = settings.ddr3.sdram_tim3; + draco_ddr3_emif_reg_data.emif_ddr_phy_ctlr_1 = settings.ddr3.emif_ddr_phy_ctlr_1; - dxr2_ddr3_emif_reg_data.sdram_config = settings.ddr3.sdram_config; - dxr2_ddr3_emif_reg_data.ref_ctrl = settings.ddr3.ref_ctrl; - - dxr2_ddr3_data.datardsratio0 = settings.ddr3.dt0rdsratio0; - dxr2_ddr3_data.datawdsratio0 = settings.ddr3.dt0wdsratio0; - dxr2_ddr3_data.datafwsratio0 = settings.ddr3.dt0fwsratio0; - dxr2_ddr3_data.datawrsratio0 = settings.ddr3.dt0wrsratio0; - - dxr2_ddr3_cmd_ctrl_data.cmd0csratio = settings.ddr3.ddr3_sratio; - dxr2_ddr3_cmd_ctrl_data.cmd0iclkout = settings.ddr3.iclkout; - dxr2_ddr3_cmd_ctrl_data.cmd1csratio = settings.ddr3.ddr3_sratio; - dxr2_ddr3_cmd_ctrl_data.cmd1iclkout = settings.ddr3.iclkout; - dxr2_ddr3_cmd_ctrl_data.cmd2csratio = settings.ddr3.ddr3_sratio; - dxr2_ddr3_cmd_ctrl_data.cmd2iclkout = settings.ddr3.iclkout; - - dxr2_ddr3_ioregs.cm0ioctl = settings.ddr3.ioctr_val, - dxr2_ddr3_ioregs.cm1ioctl = settings.ddr3.ioctr_val, - dxr2_ddr3_ioregs.cm2ioctl = settings.ddr3.ioctr_val, - dxr2_ddr3_ioregs.dt0ioctl = settings.ddr3.ioctr_val, - dxr2_ddr3_ioregs.dt1ioctl = settings.ddr3.ioctr_val, - - config_ddr(DDR_PLL_FREQ, &dxr2_ddr3_ioregs, &dxr2_ddr3_data, - &dxr2_ddr3_cmd_ctrl_data, &dxr2_ddr3_emif_reg_data, 0); + draco_ddr3_emif_reg_data.sdram_config = settings.ddr3.sdram_config; + draco_ddr3_emif_reg_data.ref_ctrl = settings.ddr3.ref_ctrl; + + draco_ddr3_data.datardsratio0 = settings.ddr3.dt0rdsratio0; + draco_ddr3_data.datawdsratio0 = settings.ddr3.dt0wdsratio0; + draco_ddr3_data.datafwsratio0 = settings.ddr3.dt0fwsratio0; + draco_ddr3_data.datawrsratio0 = settings.ddr3.dt0wrsratio0; + + draco_ddr3_cmd_ctrl_data.cmd0csratio = settings.ddr3.ddr3_sratio; + draco_ddr3_cmd_ctrl_data.cmd0iclkout = settings.ddr3.iclkout; + draco_ddr3_cmd_ctrl_data.cmd1csratio = settings.ddr3.ddr3_sratio; + draco_ddr3_cmd_ctrl_data.cmd1iclkout = settings.ddr3.iclkout; + draco_ddr3_cmd_ctrl_data.cmd2csratio = settings.ddr3.ddr3_sratio; + draco_ddr3_cmd_ctrl_data.cmd2iclkout = settings.ddr3.iclkout; + + draco_ddr3_ioregs.cm0ioctl = settings.ddr3.ioctr_val, + draco_ddr3_ioregs.cm1ioctl = settings.ddr3.ioctr_val, + draco_ddr3_ioregs.cm2ioctl = settings.ddr3.ioctr_val, + draco_ddr3_ioregs.dt0ioctl = settings.ddr3.ioctr_val, + draco_ddr3_ioregs.dt1ioctl = settings.ddr3.ioctr_val, + + config_ddr(DDR_PLL_FREQ, &draco_ddr3_ioregs, &draco_ddr3_data, + &draco_ddr3_cmd_ctrl_data, &draco_ddr3_emif_reg_data, 0); } static void spl_siemens_board_init(void) diff --git a/board/siemens/dxr2/board.h b/board/siemens/draco/board.h index abf5432329..ff8ab764c5 100644 --- a/board/siemens/dxr2/board.h +++ b/board/siemens/draco/board.h @@ -22,24 +22,26 @@ #define MAGIC_CHIP 0x50494843 /* Automatic generated definition */ -/* Wed, 18 Sep 2013 18:58:27 +0200 */ -/* From file: draco/ddr3-data-micron-v2.txt */ +/* Wed, 16 Apr 2014 16:50:41 +0200 */ +/* From file: draco/ddr3-data-universal-default@303MHz-i0-ES3.txt */ struct ddr3_data { unsigned int magic; /* 0x33524444 */ - unsigned int version; /* 0x56312e34 */ - unsigned short int ddr3_sratio; /* 0x0100 */ - unsigned short int iclkout; /* 0x0001 */ + unsigned int version; /* 0x56312e35 */ + unsigned short int ddr3_sratio; /* 0x0080 */ + unsigned short int iclkout; /* 0x0000 */ unsigned short int dt0rdsratio0; /* 0x003A */ - unsigned short int dt0wdsratio0; /* 0x008A */ - unsigned short int dt0fwsratio0; /* 0x010B */ - unsigned short int dt0wrsratio0; /* 0x00C4 */ + unsigned short int dt0wdsratio0; /* 0x003F */ + unsigned short int dt0fwsratio0; /* 0x009F */ + unsigned short int dt0wrsratio0; /* 0x0079 */ unsigned int sdram_tim1; /* 0x0888A39B */ unsigned int sdram_tim2; /* 0x26247FDA */ unsigned int sdram_tim3; /* 0x501F821F */ unsigned int emif_ddr_phy_ctlr_1; /* 0x00100206 */ - unsigned int sdram_config; /* 0x61C04AB2 */ - unsigned int ref_ctrl; /* 0x00000618 */ - unsigned int ioctr_val; /* 0x0000018B */ + unsigned int sdram_config; /* 0x61A44A32 */ + unsigned int ref_ctrl; /* 0x0000093B */ + unsigned int ioctr_val; /* 0x0000014A */ + char manu_name[32]; /* "default@303MHz \0" */ + char manu_marking[32]; /* "default \0" */ }; struct chip_data { @@ -48,7 +50,7 @@ struct chip_data { char shwver[7]; }; -struct dxr2_baseboard_id { +struct draco_baseboard_id { struct ddr3_data ddr3; struct chip_data chip; }; diff --git a/board/siemens/dxr2/mux.c b/board/siemens/draco/mux.c index f2314b5d3e..eaa3c70798 100644 --- a/board/siemens/dxr2/mux.c +++ b/board/siemens/draco/mux.c @@ -1,5 +1,5 @@ /* - * pinmux setup for siemens dxr2 board + * pinmux setup for siemens draco board * * (C) Copyright 2013 Siemens Schweiz AG * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. diff --git a/board/siemens/pxm2/board.c b/board/siemens/pxm2/board.c index 98083d52cd..64e69dc93d 100644 --- a/board/siemens/pxm2/board.c +++ b/board/siemens/pxm2/board.c @@ -70,11 +70,11 @@ struct cmd_control pxm2_ddr3_cmd_ctrl_data = { }; const struct ctrl_ioregs ioregs = { - .cm0ioctl = DXR2_IOCTRL_VAL, - .cm1ioctl = DXR2_IOCTRL_VAL, - .cm2ioctl = DXR2_IOCTRL_VAL, - .dt0ioctl = DXR2_IOCTRL_VAL, - .dt1ioctl = DXR2_IOCTRL_VAL, + .cm0ioctl = DDR_IOCTRL_VAL, + .cm1ioctl = DDR_IOCTRL_VAL, + .cm2ioctl = DDR_IOCTRL_VAL, + .dt0ioctl = DDR_IOCTRL_VAL, + .dt1ioctl = DDR_IOCTRL_VAL, }; config_ddr(DDR_PLL_FREQ, &ioregs, &pxm2_ddr3_data, diff --git a/board/siemens/rut/board.c b/board/siemens/rut/board.c index e0ada3f6a5..1752df2c4f 100644 --- a/board/siemens/rut/board.c +++ b/board/siemens/rut/board.c @@ -400,7 +400,7 @@ static int conf_disp_pll(int m, int n) #if defined(DISPL_PLL_SPREAD_SPECTRUM) writel(0x64, &cmwkup->resv6[3]); /* 0x50 */ writel(0x800, &cmwkup->resv6[2]); /* 0x4c */ - writel(readl(&cmwkup->clkmoddplldisp) | (1 << 12), + writel(readl(&cmwkup->clkmoddplldisp) | CM_CLKMODE_DPLL_SSC_EN_MASK, &cmwkup->clkmoddplldisp); /* 0x98 */ #endif return 0; diff --git a/board/ti/am335x/u-boot.lds b/board/ti/am335x/u-boot.lds index a9e3d34df9..2c5a0f8a11 100644 --- a/board/ti/am335x/u-boot.lds +++ b/board/ti/am335x/u-boot.lds @@ -34,6 +34,7 @@ SECTIONS .text : { *(.__image_copy_start) + *(.vectors) CPUDIR/start.o (.text*) board/ti/am335x/built-in.o (.text*) *(.text*) diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c index f1951dc5ef..3c8b7a5d2d 100644 --- a/board/wandboard/wandboard.c +++ b/board/wandboard/wandboard.c @@ -1,5 +1,6 @@ /* * Copyright (C) 2013 Freescale Semiconductor, Inc. + * Copyright (C) 2014 O.S. Systems Software LTDA. * * Author: Fabio Estevam <fabio.estevam@freescale.com> * @@ -15,18 +16,19 @@ #include <asm/arch/sys_proto.h> #include <asm/gpio.h> #include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/mxc_i2c.h> #include <asm/imx-common/boot_mode.h> +#include <asm/imx-common/video.h> #include <asm/io.h> #include <linux/sizes.h> #include <common.h> #include <fsl_esdhc.h> -#include <ipu_pixfmt.h> #include <mmc.h> #include <miiphy.h> #include <netdev.h> -#include <linux/fb.h> #include <phy.h> #include <input.h> +#include <i2c.h> DECLARE_GLOBAL_DATA_PTR; @@ -41,6 +43,10 @@ DECLARE_GLOBAL_DATA_PTR; #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) +#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE | PAD_CTL_SRE_FAST) + #define USDHC1_CD_GPIO IMX_GPIO_NR(1, 2) #define USDHC3_CD_GPIO IMX_GPIO_NR(3, 9) #define ETH_PHY_RESET IMX_GPIO_NR(3, 29) @@ -210,38 +216,120 @@ int board_phy_config(struct phy_device *phydev) } #if defined(CONFIG_VIDEO_IPUV3) -static struct fb_videomode const hdmi = { - .name = "HDMI", - .refresh = 60, - .xres = 1024, - .yres = 768, - .pixclock = 15385, - .left_margin = 220, - .right_margin = 40, - .upper_margin = 21, - .lower_margin = 7, - .hsync_len = 60, - .vsync_len = 10, - .sync = FB_SYNC_EXT, - .vmode = FB_VMODE_NONINTERLACED +struct i2c_pads_info i2c2_pad_info = { + .scl = { + .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gp = IMX_GPIO_NR(4, 12) + }, + .sda = { + .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 + | MUX_PAD_CTRL(I2C_PAD_CTRL), + .gp = IMX_GPIO_NR(4, 13) + } }; -int board_video_skip(void) -{ - int ret; +static iomux_v3_cfg_t const fwadapt_7wvga_pads[] = { + MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK, + MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02, /* HSync */ + MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03, /* VSync */ + MX6_PAD_DI0_PIN4__IPU1_DI0_PIN04 + | MUX_PAD_CTRL(PAD_CTL_DSE_120ohm), /* Contrast */ + MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15, /* DISP0_DRDY */ + + MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00, + MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01, + MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02, + MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03, + MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04, + MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05, + MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06, + MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07, + MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08, + MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09, + MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10, + MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11, + MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12, + MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13, + MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14, + MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15, + MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16, + MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17, + + MX6_PAD_SD4_DAT2__GPIO2_IO10 + | MUX_PAD_CTRL(NO_PAD_CTRL), /* DISP0_BKLEN */ + MX6_PAD_SD4_DAT3__GPIO2_IO11 + | MUX_PAD_CTRL(NO_PAD_CTRL), /* DISP0_VDDEN */ +}; - ret = ipuv3_fb_init(&hdmi, 0, IPU_PIX_FMT_RGB24); +static void do_enable_hdmi(struct display_info_t const *dev) +{ + imx_enable_hdmi_phy(); +} - if (ret) { - printf("HDMI cannot be configured: %d\n", ret); - return ret; - } +static int detect_i2c(struct display_info_t const *dev) +{ + return (0 == i2c_set_bus_num(dev->bus)) && + (0 == i2c_probe(dev->addr)); +} - imx_enable_hdmi_phy(); +static void enable_fwadapt_7wvga(struct display_info_t const *dev) +{ + imx_iomux_v3_setup_multiple_pads( + fwadapt_7wvga_pads, + ARRAY_SIZE(fwadapt_7wvga_pads)); - return ret; + gpio_direction_output(IMX_GPIO_NR(2, 10), 1); + gpio_direction_output(IMX_GPIO_NR(2, 11), 1); } +struct display_info_t const displays[] = {{ + .bus = -1, + .addr = 0, + .pixfmt = IPU_PIX_FMT_RGB24, + .detect = detect_hdmi, + .enable = do_enable_hdmi, + .mode = { + .name = "HDMI", + .refresh = 60, + .xres = 1024, + .yres = 768, + .pixclock = 15385, + .left_margin = 220, + .right_margin = 40, + .upper_margin = 21, + .lower_margin = 7, + .hsync_len = 60, + .vsync_len = 10, + .sync = FB_SYNC_EXT, + .vmode = FB_VMODE_NONINTERLACED +} }, { + .bus = 1, + .addr = 0x10, + .pixfmt = IPU_PIX_FMT_RGB666, + .detect = detect_i2c, + .enable = enable_fwadapt_7wvga, + .mode = { + .name = "FWBADAPT-LCD-F07A-0102", + .refresh = 60, + .xres = 800, + .yres = 480, + .pixclock = 33260, + .left_margin = 128, + .right_margin = 128, + .upper_margin = 22, + .lower_margin = 22, + .hsync_len = 1, + .vsync_len = 1, + .sync = 0, + .vmode = FB_VMODE_NONINTERLACED +} } }; +size_t display_count = ARRAY_SIZE(displays); + static void setup_display(void) { struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; @@ -254,6 +342,10 @@ static void setup_display(void) reg |= (CHSCCDR_CLK_SEL_LDB_DI0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); writel(reg, &mxc_ccm->chsccdr); + + /* Disable LCD backlight */ + imx_iomux_v3_setup_pad(MX6_PAD_DI0_PIN4__GPIO4_IO20); + gpio_direction_input(IMX_GPIO_NR(4, 20)); } #endif /* CONFIG_VIDEO_IPUV3 */ @@ -305,6 +397,8 @@ int board_init(void) /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c2_pad_info); + return 0; } diff --git a/boards.cfg b/boards.cfg index 9d90550794..d31bdba5c7 100644 --- a/boards.cfg +++ b/boards.cfg @@ -257,10 +257,12 @@ Active arm armv7 am33xx BuR tseries Active arm armv7 am33xx BuR tseries tseries_nand tseries:SERIAL1,CONS_INDEX=1,NAND Hannes Petermaier <hannes.petermaier@br-automation.com> Active arm armv7 am33xx BuR tseries tseries_spi tseries:SERIAL1,CONS_INDEX=1,SPI_BOOT,EMMC_BOOT Hannes Petermaier <hannes.petermaier@br-automation.com> Active arm armv7 am33xx compulab cm_t335 cm_t335 - Igor Grinberg <grinberg@compulab.co.il> +Active arm armv7 am33xx gumstix pepper pepper - Ash Charles <ash@gumstix.com> Active arm armv7 am33xx isee igep0033 am335x_igep0033 - Enric Balletbo i Serra <eballetbo@iseebcn.com> Active arm armv7 am33xx phytec pcm051 pcm051_rev1 pcm051:REV1 Lars Poeschel <poeschel@lemonage.de> Active arm armv7 am33xx phytec pcm051 pcm051_rev3 pcm051:REV3 Lars Poeschel <poeschel@lemonage.de> -Active arm armv7 am33xx siemens dxr2 dxr2 - Roger Meier <r.meier@siemens.com> +Active arm armv7 am33xx siemens draco draco - Roger Meier <r.meier@siemens.com> +Active arm armv7 am33xx siemens draco dxr2 - Roger Meier <r.meier@siemens.com> Active arm armv7 am33xx siemens pxm2 pxm2 - Roger Meier <r.meier@siemens.com> Active arm armv7 am33xx siemens rut rut - Roger Meier <r.meier@siemens.com> Active arm armv7 am33xx silica pengwyn pengwyn - Lothar Felten <lothar.felten@gmail.com> @@ -318,6 +320,8 @@ Active arm armv7 mx6 boundary nitrogen6x Active arm armv7 mx6 boundary nitrogen6x nitrogen6s nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s.cfg,MX6S,DDR_MB=512 Eric Nelson <eric.nelson@boundarydevices.com> Active arm armv7 mx6 boundary nitrogen6x nitrogen6s1g nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s1g.cfg,MX6S,DDR_MB=1024 Eric Nelson <eric.nelson@boundarydevices.com> Active arm armv7 mx6 congatec cgtqmx6eval cgtqmx6qeval cgtqmx6eval:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg,MX6Q Leo Sartre <lsartre@adeneo-embedded.com> +Active arm armv7 mx6 embest mx6boards marsboard embestmx6boards:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6q.cfg,MX6Q,DDR_MB=1024,ENV_IS_IN_SPI_FLASH Eric Bénard <eric@eukrea.com> +Active arm armv7 mx6 embest mx6boards riotboard embestmx6boards:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s1g.cfg,MX6S,DDR_MB=1024,ENV_IS_IN_MMC Eric Bénard <eric@eukrea.com> Active arm armv7 mx6 freescale mx6qarm2 mx6qarm2 mx6qarm2:IMX_CONFIG=board/freescale/mx6qarm2/imximage.cfg Jason Liu <r64343@freescale.com> Active arm armv7 mx6 freescale mx6qsabreauto mx6qsabreauto mx6qsabreauto:IMX_CONFIG=board/freescale/mx6qsabreauto/imximage.cfg,MX6Q Fabio Estevam <fabio.estevam@freescale.com> Active arm armv7 mx6 freescale mx6sabresd mx6dlsabresd mx6sabresd:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL Fabio Estevam <fabio.estevam@freescale.com> @@ -370,7 +374,7 @@ Active arm armv7 rmobile renesas koelsch Active arm armv7 rmobile renesas koelsch koelsch_nor koelsch:NORFLASH Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Active arm armv7 rmobile renesas lager lager - Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Active arm armv7 rmobile renesas lager lager_nor lager:NORFLASH Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> -Active arm armv7 s5pc1xx samsung goni s5p_goni - Mateusz Zalega <m.zalega@samsung.com> +Active arm armv7 s5pc1xx samsung goni s5p_goni - Przemyslaw Marczak <p.marczak@samsung.com> Active arm armv7 s5pc1xx samsung smdkc100 smdkc100 - Minkyu Kang <mk7.kang@samsung.com> Active arm armv7 socfpga altera socfpga socfpga_cyclone5 - - Active arm armv7 u8500 st-ericsson snowball snowball - Mathieu Poirier <mathieu.poirier@linaro.org> @@ -812,8 +816,8 @@ Active powerpc mpc85xx - freescale mpc8568mds Active powerpc mpc85xx - freescale mpc8569mds MPC8569MDS - - Active powerpc mpc85xx - freescale mpc8569mds MPC8569MDS_ATM MPC8569MDS:ATM - Active powerpc mpc85xx - freescale mpc8569mds MPC8569MDS_NAND MPC8569MDS:NAND - -Active powerpc mpc85xx - freescale mpc8572ds MPC8572DS - - -Active powerpc mpc85xx - freescale mpc8572ds MPC8572DS_36BIT MPC8572DS:36BIT - +Active powerpc mpc85xx - freescale mpc8572ds MPC8572DS - York Sun <yorksun@freescale.com> +Active powerpc mpc85xx - freescale mpc8572ds MPC8572DS_36BIT MPC8572DS:36BIT York Sun <yorksun@freescale.com> Active powerpc mpc85xx - freescale mpc8572ds MPC8572DS_NAND MPC8572DS:NAND - Active powerpc mpc85xx - freescale p1010rdb P1010RDB-PA_36BIT_NAND P1010RDB:P1010RDB_PA,36BIT,NAND - Active powerpc mpc85xx - freescale p1010rdb P1010RDB-PA_36BIT_NAND_SECBOOT P1010RDB:P1010RDB_PA,36BIT,NAND_SECBOOT,SECURE_BOOT - @@ -969,6 +973,7 @@ Active powerpc mpc85xx - freescale t208xqds Active powerpc mpc85xx - freescale t208xrdb T2080RDB T208xRDB:PPC_T2080 - Active powerpc mpc85xx - freescale t208xrdb T2080RDB_NAND T208xRDB:PPC_T2080,RAMBOOT_PBL,SPL_FSL_PBL,NAND - Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SDCARD T208xRDB:PPC_T2080,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD - +Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SECURE_BOOT T208xRDB:PPC_T2080,SECURE_BOOT Aneesh Bansal <aneesh.bansal@freescale.com> Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SPIFLASH T208xRDB:PPC_T2080,RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH - Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SRIO_PCIE_BOOT T208xRDB:PPC_T2080,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000 - Active powerpc mpc85xx - freescale t4qds T4160QDS T4240QDS:PPC_T4160 - @@ -983,6 +988,8 @@ Active powerpc mpc85xx - freescale t4qds Active powerpc mpc85xx - freescale t4qds T4240QDS_SECURE_BOOT T4240QDS:PPC_T4240,SECURE_BOOT Aneesh Bansal <aneesh.bansal@freescale.com> Active powerpc mpc85xx - freescale t4qds T4240QDS_SPIFLASH T4240QDS:PPC_T4240,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000 - Active powerpc mpc85xx - freescale t4qds T4240QDS_SRIO_PCIE_BOOT T4240QDS:PPC_T4240,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000 - +Active powerpc mpc85xx - freescale t4rdb T4160RDB T4240RDB:PPC_T4160 Chunhe Lan <Chunhe.Lan@freescale.com> +Active powerpc mpc85xx - freescale t4rdb T4240RDB T4240RDB:PPC_T4240 Chunhe Lan <Chunhe.Lan@freescale.com> Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD controlcenterd:36BIT,SDCARD Dirk Eibach <eibach@gdsys.de> Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD_DEVELOP controlcenterd:36BIT,SDCARD,DEVELOP Dirk Eibach <eibach@gdsys.de> Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER controlcenterd:TRAILBLAZER,SPIFLASH Dirk Eibach <eibach@gdsys.de> @@ -1182,7 +1189,7 @@ Active powerpc ppc4xx - xilinx ppc405-generic Active powerpc ppc4xx - xilinx ppc405-generic xilinx-ppc405-generic_flash xilinx-ppc405-generic:SYS_TEXT_BASE=0xF7F60000,RESET_VECTOR_ADDRESS=0xF7FFFFFC Ricardo Ribalda <ricardo.ribalda@uam.es> Active powerpc ppc4xx - xilinx ppc440-generic xilinx-ppc440-generic xilinx-ppc440-generic:SYS_TEXT_BASE=0x04000000,RESET_VECTOR_ADDRESS=0x04100000,BOOT_FROM_XMD=1 Ricardo Ribalda <ricardo.ribalda@uam.es> Active powerpc ppc4xx - xilinx ppc440-generic xilinx-ppc440-generic_flash xilinx-ppc440-generic:SYS_TEXT_BASE=0xF7F60000,RESET_VECTOR_ADDRESS=0xF7FFFFFC Ricardo Ribalda <ricardo.ribalda@uam.es> -Active sandbox sandbox - - <none> sandbox - Simon Glass <sjg@chromium.org> +Active sandbox sandbox - - sandbox sandbox - Simon Glass <sjg@chromium.org> Active sh sh2 - renesas rsk7203 rsk7203 - Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>:Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Active sh sh2 - renesas rsk7264 rsk7264 - Phil Edworthy <phil.edworthy@renesas.com> Active sh sh2 - renesas rsk7269 rsk7269 - - diff --git a/common/Makefile b/common/Makefile index 7c853ae442..219cb51b2d 100644 --- a/common/Makefile +++ b/common/Makefile @@ -168,6 +168,8 @@ obj-y += cmd_usb.o obj-y += usb.o usb_hub.o obj-$(CONFIG_USB_STORAGE) += usb_storage.o endif +obj-$(CONFIG_CMD_FASTBOOT) += cmd_fastboot.o + obj-$(CONFIG_CMD_USB_MASS_STORAGE) += cmd_usb_mass_storage.o obj-$(CONFIG_CMD_THOR_DOWNLOAD) += cmd_thordown.o obj-$(CONFIG_CMD_XIMG) += cmd_ximg.o @@ -237,6 +239,7 @@ obj-y += console.o obj-$(CONFIG_CROS_EC) += cros_ec.o obj-y += dlmalloc.o obj-y += image.o +obj-$(CONFIG_ANDROID_BOOT_IMAGE) += image-android.o obj-$(CONFIG_OF_LIBFDT) += image-fdt.o obj-$(CONFIG_FIT) += image-fit.o obj-$(CONFIG_FIT_SIGNATURE) += image-sig.o diff --git a/common/cmd_bootm.c b/common/cmd_bootm.c index e683af3691..34b4b583ba 100644 --- a/common/cmd_bootm.c +++ b/common/cmd_bootm.c @@ -222,6 +222,7 @@ static int bootm_find_os(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { const void *os_hdr; + bool ep_found = false; /* get kernel image header, start address and length */ os_hdr = boot_get_kernel(cmdtp, flag, argc, argv, @@ -274,6 +275,18 @@ static int bootm_find_os(cmd_tbl_t *cmdtp, int flag, int argc, } break; #endif +#ifdef CONFIG_ANDROID_BOOT_IMAGE + case IMAGE_FORMAT_ANDROID: + images.os.type = IH_TYPE_KERNEL; + images.os.comp = IH_COMP_NONE; + images.os.os = IH_OS_LINUX; + images.ep = images.os.load; + ep_found = true; + + images.os.end = android_image_get_end(os_hdr); + images.os.load = android_image_get_kload(os_hdr); + break; +#endif default: puts("ERROR: unknown image format type!\n"); return 1; @@ -293,7 +306,7 @@ static int bootm_find_os(cmd_tbl_t *cmdtp, int flag, int argc, return 1; } #endif - } else { + } else if (!ep_found) { puts("Could not find kernel entry point!\n"); return 1; } @@ -1002,6 +1015,14 @@ static const void *boot_get_kernel(cmd_tbl_t *cmdtp, int flag, int argc, images->fit_noffset_os = os_noffset; break; #endif +#ifdef CONFIG_ANDROID_BOOT_IMAGE + case IMAGE_FORMAT_ANDROID: + printf("## Booting Android Image at 0x%08lx ...\n", img_addr); + if (android_image_get_kernel((void *)img_addr, images->verify, + os_data, os_len)) + return NULL; + break; +#endif default: printf("Wrong Image Format for %s command\n", cmdtp->name); bootstage_error(BOOTSTAGE_ID_FIT_KERNEL_INFO); diff --git a/common/cmd_fastboot.c b/common/cmd_fastboot.c new file mode 100644 index 0000000000..83fa7bdded --- /dev/null +++ b/common/cmd_fastboot.c @@ -0,0 +1,36 @@ +/* + * Copyright 2008 - 2009 Windriver, <www.windriver.com> + * Author: Tom Rix <Tom.Rix@windriver.com> + * + * (C) Copyright 2014 Linaro, Ltd. + * Rob Herring <robh@kernel.org> + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#include <common.h> +#include <command.h> +#include <g_dnl.h> + +static int do_fastboot(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) +{ + int ret; + + ret = g_dnl_register("usb_dnl_fastboot"); + if (ret) + return ret; + + while (1) { + if (ctrlc()) + break; + usb_gadget_handle_interrupts(); + } + + g_dnl_unregister(); + return CMD_RET_SUCCESS; +} + +U_BOOT_CMD( + fastboot, 1, 1, do_fastboot, + "fastboot - enter USB Fastboot protocol", + "" +); diff --git a/common/cmd_fpga.c b/common/cmd_fpga.c index 010cd24e63..bda5c8f798 100644 --- a/common/cmd_fpga.c +++ b/common/cmd_fpga.c @@ -11,6 +11,7 @@ #include <common.h> #include <command.h> #include <fpga.h> +#include <fs.h> #include <malloc.h> /* Local functions */ @@ -23,6 +24,9 @@ static int fpga_get_op(char *opstr); #define FPGA_LOADB 2 #define FPGA_DUMP 3 #define FPGA_LOADMK 4 +#define FPGA_LOADP 5 +#define FPGA_LOADBP 6 +#define FPGA_LOADFS 7 /* ------------------------------------------------------------------------- */ /* command form: @@ -45,6 +49,10 @@ int do_fpga(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) const char *fit_uname = NULL; ulong fit_addr; #endif +#if defined(CONFIG_CMD_FPGA_LOADFS) + fpga_fs_info fpga_fsinfo; + fpga_fsinfo.fstype = FS_TYPE_ANY; +#endif if (devstr) dev = (int) simple_strtoul(devstr, NULL, 16); @@ -52,6 +60,14 @@ int do_fpga(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) fpga_data = (void *)simple_strtoul(datastr, NULL, 16); switch (argc) { +#if defined(CONFIG_CMD_FPGA_LOADFS) + case 9: + fpga_fsinfo.blocksize = (unsigned int) + simple_strtoul(argv[5], NULL, 16); + fpga_fsinfo.interface = argv[6]; + fpga_fsinfo.dev_part = argv[7]; + fpga_fsinfo.filename = argv[8]; +#endif case 5: /* fpga <op> <dev> <data> <datasize> */ data_size = simple_strtoul(argv[4], NULL, 16); @@ -120,16 +136,27 @@ int do_fpga(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) case FPGA_NONE: case FPGA_INFO: break; +#if defined(CONFIG_CMD_FPGA_LOADFS) + case FPGA_LOADFS: + /* Blocksize can be zero */ + if (!fpga_fsinfo.interface || !fpga_fsinfo.dev_part || + !fpga_fsinfo.filename) + wrong_parms = 1; +#endif case FPGA_LOAD: + case FPGA_LOADP: case FPGA_LOADB: + case FPGA_LOADBP: case FPGA_DUMP: if (!fpga_data || !data_size) wrong_parms = 1; break; +#if defined(CONFIG_CMD_FPGA_LOADMK) case FPGA_LOADMK: if (!fpga_data) wrong_parms = 1; break; +#endif } if (wrong_parms) { @@ -146,13 +173,32 @@ int do_fpga(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) break; case FPGA_LOAD: - rc = fpga_load(dev, fpga_data, data_size); + rc = fpga_load(dev, fpga_data, data_size, BIT_FULL); + break; + +#if defined(CONFIG_CMD_FPGA_LOADP) + case FPGA_LOADP: + rc = fpga_load(dev, fpga_data, data_size, BIT_PARTIAL); break; +#endif case FPGA_LOADB: - rc = fpga_loadbitstream(dev, fpga_data, data_size); + rc = fpga_loadbitstream(dev, fpga_data, data_size, BIT_FULL); + break; + +#if defined(CONFIG_CMD_FPGA_LOADBP) + case FPGA_LOADBP: + rc = fpga_loadbitstream(dev, fpga_data, data_size, BIT_PARTIAL); + break; +#endif + +#if defined(CONFIG_CMD_FPGA_LOADFS) + case FPGA_LOADFS: + rc = fpga_fsload(dev, fpga_data, data_size, &fpga_fsinfo); break; +#endif +#if defined(CONFIG_CMD_FPGA_LOADMK) case FPGA_LOADMK: switch (genimg_get_format(fpga_data)) { case IMAGE_FORMAT_LEGACY: @@ -179,7 +225,8 @@ int do_fpga(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) data = (ulong)image_get_data(hdr); data_size = image_get_data_size(hdr); } - rc = fpga_load(dev, (void *)data, data_size); + rc = fpga_load(dev, (void *)data, data_size, + BIT_FULL); } break; #if defined(CONFIG_FIT) @@ -221,7 +268,8 @@ int do_fpga(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) return 1; } - rc = fpga_load(dev, fit_data, data_size); + rc = fpga_load(dev, fit_data, data_size, + BIT_FULL); } break; #endif @@ -231,6 +279,7 @@ int do_fpga(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) break; } break; +#endif case FPGA_DUMP: rc = fpga_dump(dev, fpga_data, data_size); @@ -257,8 +306,22 @@ static int fpga_get_op(char *opstr) op = FPGA_LOADB; else if (!strcmp("load", opstr)) op = FPGA_LOAD; +#if defined(CONFIG_CMD_FPGA_LOADP) + else if (!strcmp("loadp", opstr)) + op = FPGA_LOADP; +#endif +#if defined(CONFIG_CMD_FPGA_LOADBP) + else if (!strcmp("loadbp", opstr)) + op = FPGA_LOADBP; +#endif +#if defined(CONFIG_CMD_FPGA_LOADFS) + else if (!strcmp("loadfs", opstr)) + op = FPGA_LOADFS; +#endif +#if defined(CONFIG_CMD_FPGA_LOADMK) else if (!strcmp("loadmk", opstr)) op = FPGA_LOADMK; +#endif else if (!strcmp("dump", opstr)) op = FPGA_DUMP; @@ -268,19 +331,39 @@ static int fpga_get_op(char *opstr) return op; } +#if defined(CONFIG_CMD_FPGA_LOADFS) +U_BOOT_CMD(fpga, 9, 1, do_fpga, +#else U_BOOT_CMD(fpga, 6, 1, do_fpga, +#endif "loadable FPGA image support", "[operation type] [device number] [image address] [image size]\n" "fpga operations:\n" " dump\t[dev]\t\t\tLoad device to memory buffer\n" " info\t[dev]\t\t\tlist known device information\n" " load\t[dev] [address] [size]\tLoad device from memory buffer\n" +#if defined(CONFIG_CMD_FPGA_LOADP) + " loadp\t[dev] [address] [size]\t" + "Load device from memory buffer with partial bitstream\n" +#endif " loadb\t[dev] [address] [size]\t" "Load device from bitstream buffer (Xilinx only)\n" +#if defined(CONFIG_CMD_FPGA_LOADBP) + " loadbp\t[dev] [address] [size]\t" + "Load device from bitstream buffer with partial bitstream" + "(Xilinx only)\n" +#endif +#if defined(CONFIG_CMD_FPGA_LOADFS) + "Load device from filesystem (FAT by default) (Xilinx only)\n" + " loadfs [dev] [address] [image size] [blocksize] <interface>\n" + " [<dev[:part]>] <filename>\n" +#endif +#if defined(CONFIG_CMD_FPGA_LOADMK) " loadmk [dev] [address]\tLoad device generated with mkimage" #if defined(CONFIG_FIT) "\n" "\tFor loadmk operating on FIT format uImage address must include\n" "\tsubimage unit name in the form of addr:<subimg_uname>" #endif +#endif ); diff --git a/common/cmd_fuse.c b/common/cmd_fuse.c index 0df57dbc80..abab9789b0 100644 --- a/common/cmd_fuse.c +++ b/common/cmd_fuse.c @@ -33,15 +33,8 @@ static int confirm_prog(void) "what you are doing!\n" "\nReally perform this fuse programming? <y/N>\n"); - if (getc() == 'y') { - int c; - - putc('y'); - c = getc(); - putc('\n'); - if (c == '\r') - return 1; - } + if (confirm_yesno()) + return 1; puts("Fuse programming aborted\n"); return 0; diff --git a/common/cmd_mmc.c b/common/cmd_mmc.c index c1916c9b56..eea337506c 100644 --- a/common/cmd_mmc.c +++ b/common/cmd_mmc.c @@ -71,12 +71,6 @@ U_BOOT_CMD( ); #else /* !CONFIG_GENERIC_MMC */ -enum mmc_state { - MMC_INVALID, - MMC_READ, - MMC_WRITE, - MMC_ERASE, -}; static void print_mmcinfo(struct mmc *mmc) { printf("Device: %s\n", mmc->cfg->name); @@ -98,7 +92,18 @@ static void print_mmcinfo(struct mmc *mmc) printf("Bus Width: %d-bit\n", mmc->bus_width); } - +static struct mmc *init_mmc_device(int dev) +{ + struct mmc *mmc; + mmc = find_mmc_device(dev); + if (!mmc) { + printf("no mmc device at slot %x\n", dev); + return NULL; + } + if (mmc_init(mmc)) + return NULL; + return mmc; +} static int do_mmcinfo(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { struct mmc *mmc; @@ -112,351 +117,537 @@ static int do_mmcinfo(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) } } - mmc = find_mmc_device(curr_device); + mmc = init_mmc_device(curr_device); + if (!mmc) + return CMD_RET_FAILURE; - if (mmc) { - mmc_init(mmc); + print_mmcinfo(mmc); + return CMD_RET_SUCCESS; +} - print_mmcinfo(mmc); - return 0; - } else { - printf("no mmc device at slot %x\n", curr_device); +#ifdef CONFIG_SUPPORT_EMMC_RPMB +static int confirm_key_prog(void) +{ + puts("Warning: Programming authentication key can be done only once !\n" + " Use this command only if you are sure of what you are doing,\n" + "Really perform the key programming? <y/N> "); + if (confirm_yesno()) return 1; + + puts("Authentication key programming aborted\n"); + return 0; +} +static int do_mmcrpmb_key(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + void *key_addr; + struct mmc *mmc = find_mmc_device(curr_device); + + if (argc != 2) + return CMD_RET_USAGE; + + key_addr = (void *)simple_strtoul(argv[1], NULL, 16); + if (!confirm_key_prog()) + return CMD_RET_FAILURE; + if (mmc_rpmb_set_key(mmc, key_addr)) { + printf("ERROR - Key already programmed ?\n"); + return CMD_RET_FAILURE; } + return CMD_RET_SUCCESS; } +static int do_mmcrpmb_read(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + u16 blk, cnt; + void *addr; + int n; + void *key_addr = NULL; + struct mmc *mmc = find_mmc_device(curr_device); -U_BOOT_CMD( - mmcinfo, 1, 0, do_mmcinfo, - "display MMC info", - "- display info of the current MMC device" -); + if (argc < 4) + return CMD_RET_USAGE; -static int do_mmcops(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) + addr = (void *)simple_strtoul(argv[1], NULL, 16); + blk = simple_strtoul(argv[2], NULL, 16); + cnt = simple_strtoul(argv[3], NULL, 16); + + if (argc == 5) + key_addr = (void *)simple_strtoul(argv[4], NULL, 16); + + printf("\nMMC RPMB read: dev # %d, block # %d, count %d ... ", + curr_device, blk, cnt); + n = mmc_rpmb_read(mmc, addr, blk, cnt, key_addr); + + printf("%d RPMB blocks read: %s\n", n, (n == cnt) ? "OK" : "ERROR"); + if (n != cnt) + return CMD_RET_FAILURE; + return CMD_RET_SUCCESS; +} +static int do_mmcrpmb_write(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) { - enum mmc_state state; + u16 blk, cnt; + void *addr; + int n; + void *key_addr; + struct mmc *mmc = find_mmc_device(curr_device); - if (argc < 2) + if (argc != 5) return CMD_RET_USAGE; - if (curr_device < 0) { - if (get_mmc_num() > 0) - curr_device = 0; - else { - puts("No MMC device available\n"); - return 1; - } + addr = (void *)simple_strtoul(argv[1], NULL, 16); + blk = simple_strtoul(argv[2], NULL, 16); + cnt = simple_strtoul(argv[3], NULL, 16); + key_addr = (void *)simple_strtoul(argv[4], NULL, 16); + + printf("\nMMC RPMB write: dev # %d, block # %d, count %d ... ", + curr_device, blk, cnt); + n = mmc_rpmb_write(mmc, addr, blk, cnt, key_addr); + + printf("%d RPMB blocks written: %s\n", n, (n == cnt) ? "OK" : "ERROR"); + if (n != cnt) + return CMD_RET_FAILURE; + return CMD_RET_SUCCESS; +} +static int do_mmcrpmb_counter(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + unsigned long counter; + struct mmc *mmc = find_mmc_device(curr_device); + + if (mmc_rpmb_get_counter(mmc, &counter)) + return CMD_RET_FAILURE; + printf("RPMB Write counter= %lx\n", counter); + return CMD_RET_SUCCESS; +} + +static cmd_tbl_t cmd_rpmb[] = { + U_BOOT_CMD_MKENT(key, 2, 0, do_mmcrpmb_key, "", ""), + U_BOOT_CMD_MKENT(read, 5, 1, do_mmcrpmb_read, "", ""), + U_BOOT_CMD_MKENT(write, 5, 0, do_mmcrpmb_write, "", ""), + U_BOOT_CMD_MKENT(counter, 1, 1, do_mmcrpmb_counter, "", ""), +}; + +static int do_mmcrpmb(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + cmd_tbl_t *cp; + struct mmc *mmc; + char original_part; + int ret; + + cp = find_cmd_tbl(argv[1], cmd_rpmb, ARRAY_SIZE(cmd_rpmb)); + + /* Drop the rpmb subcommand */ + argc--; + argv++; + + if (cp == NULL || argc > cp->maxargs) + return CMD_RET_USAGE; + if (flag == CMD_FLAG_REPEAT && !cp->repeatable) + return CMD_RET_SUCCESS; + + mmc = init_mmc_device(curr_device); + if (!mmc) + return CMD_RET_FAILURE; + + if (!(mmc->version & MMC_VERSION_MMC)) { + printf("It is not a EMMC device\n"); + return CMD_RET_FAILURE; + } + if (mmc->version < MMC_VERSION_4_41) { + printf("RPMB not supported before version 4.41\n"); + return CMD_RET_FAILURE; + } + /* Switch to the RPMB partition */ + original_part = mmc->part_num; + if (mmc->part_num != MMC_PART_RPMB) { + if (mmc_switch_part(curr_device, MMC_PART_RPMB) != 0) + return CMD_RET_FAILURE; + mmc->part_num = MMC_PART_RPMB; } + ret = cp->cmd(cmdtp, flag, argc, argv); - if (strcmp(argv[1], "rescan") == 0) { - struct mmc *mmc; + /* Return to original partition */ + if (mmc->part_num != original_part) { + if (mmc_switch_part(curr_device, original_part) != 0) + return CMD_RET_FAILURE; + mmc->part_num = original_part; + } + return ret; +} +#endif - if (argc != 2) - return CMD_RET_USAGE; +static int do_mmc_read(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + struct mmc *mmc; + u32 blk, cnt, n; + void *addr; - mmc = find_mmc_device(curr_device); - if (!mmc) { - printf("no mmc device at slot %x\n", curr_device); - return 1; - } + if (argc != 4) + return CMD_RET_USAGE; - mmc->has_init = 0; + addr = (void *)simple_strtoul(argv[1], NULL, 16); + blk = simple_strtoul(argv[2], NULL, 16); + cnt = simple_strtoul(argv[3], NULL, 16); - if (mmc_init(mmc)) - return 1; - else - return 0; - } else if (strcmp(argv[1], "part") == 0) { - block_dev_desc_t *mmc_dev; - struct mmc *mmc; + mmc = init_mmc_device(curr_device); + if (!mmc) + return CMD_RET_FAILURE; - if (argc != 2) - return CMD_RET_USAGE; + printf("\nMMC read: dev # %d, block # %d, count %d ... ", + curr_device, blk, cnt); - mmc = find_mmc_device(curr_device); - if (!mmc) { - printf("no mmc device at slot %x\n", curr_device); - return 1; - } - mmc_init(mmc); - mmc_dev = mmc_get_dev(curr_device); - if (mmc_dev != NULL && - mmc_dev->type != DEV_TYPE_UNKNOWN) { - print_part(mmc_dev); - return 0; - } + n = mmc->block_dev.block_read(curr_device, blk, cnt, addr); + /* flush cache after read */ + flush_cache((ulong)addr, cnt * 512); /* FIXME */ + printf("%d blocks read: %s\n", n, (n == cnt) ? "OK" : "ERROR"); - puts("get mmc type error!\n"); - return 1; - } else if (strcmp(argv[1], "list") == 0) { - if (argc != 2) - return CMD_RET_USAGE; - print_mmc_devices('\n'); - return 0; - } else if (strcmp(argv[1], "dev") == 0) { - int dev, part = -1; - struct mmc *mmc; - - if (argc == 2) - dev = curr_device; - else if (argc == 3) - dev = simple_strtoul(argv[2], NULL, 10); - else if (argc == 4) { - dev = (int)simple_strtoul(argv[2], NULL, 10); - part = (int)simple_strtoul(argv[3], NULL, 10); - if (part > PART_ACCESS_MASK) { - printf("#part_num shouldn't be larger" - " than %d\n", PART_ACCESS_MASK); - return 1; - } - } else - return CMD_RET_USAGE; + return (n == cnt) ? CMD_RET_SUCCESS : CMD_RET_FAILURE; +} +static int do_mmc_write(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + struct mmc *mmc; + u32 blk, cnt, n; + void *addr; - mmc = find_mmc_device(dev); - if (!mmc) { - printf("no mmc device at slot %x\n", dev); - return 1; - } + if (argc != 4) + return CMD_RET_USAGE; - mmc_init(mmc); - if (part != -1) { - int ret; - if (mmc->part_config == MMCPART_NOAVAILABLE) { - printf("Card doesn't support part_switch\n"); - return 1; - } + addr = (void *)simple_strtoul(argv[1], NULL, 16); + blk = simple_strtoul(argv[2], NULL, 16); + cnt = simple_strtoul(argv[3], NULL, 16); - if (part != mmc->part_num) { - ret = mmc_switch_part(dev, part); - if (!ret) - mmc->part_num = part; + mmc = init_mmc_device(curr_device); + if (!mmc) + return CMD_RET_FAILURE; - printf("switch to partitions #%d, %s\n", - part, (!ret) ? "OK" : "ERROR"); - } - } - curr_device = dev; - if (mmc->part_config == MMCPART_NOAVAILABLE) - printf("mmc%d is current device\n", curr_device); - else - printf("mmc%d(part %d) is current device\n", - curr_device, mmc->part_num); + printf("\nMMC write: dev # %d, block # %d, count %d ... ", + curr_device, blk, cnt); - return 0; -#ifdef CONFIG_SUPPORT_EMMC_BOOT - } else if (strcmp(argv[1], "partconf") == 0) { - int dev; - struct mmc *mmc; - u8 ack, part_num, access; - - if (argc == 6) { - dev = simple_strtoul(argv[2], NULL, 10); - ack = simple_strtoul(argv[3], NULL, 10); - part_num = simple_strtoul(argv[4], NULL, 10); - access = simple_strtoul(argv[5], NULL, 10); - } else { - return CMD_RET_USAGE; - } + if (mmc_getwp(mmc) == 1) { + printf("Error: card is write protected!\n"); + return CMD_RET_FAILURE; + } + n = mmc->block_dev.block_write(curr_device, blk, cnt, addr); + printf("%d blocks written: %s\n", n, (n == cnt) ? "OK" : "ERROR"); - mmc = find_mmc_device(dev); - if (!mmc) { - printf("no mmc device at slot %x\n", dev); - return 1; - } + return (n == cnt) ? CMD_RET_SUCCESS : CMD_RET_FAILURE; +} +static int do_mmc_erase(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + struct mmc *mmc; + u32 blk, cnt, n; - if (IS_SD(mmc)) { - puts("PARTITION_CONFIG only exists on eMMC\n"); - return 1; - } + if (argc != 3) + return CMD_RET_USAGE; - /* acknowledge to be sent during boot operation */ - return mmc_set_part_conf(mmc, ack, part_num, access); - } else if (strcmp(argv[1], "bootbus") == 0) { - int dev; - struct mmc *mmc; - u8 width, reset, mode; - - if (argc == 6) { - dev = simple_strtoul(argv[2], NULL, 10); - width = simple_strtoul(argv[3], NULL, 10); - reset = simple_strtoul(argv[4], NULL, 10); - mode = simple_strtoul(argv[5], NULL, 10); - } else { - return CMD_RET_USAGE; - } + blk = simple_strtoul(argv[1], NULL, 16); + cnt = simple_strtoul(argv[2], NULL, 16); - mmc = find_mmc_device(dev); - if (!mmc) { - printf("no mmc device at slot %x\n", dev); - return 1; - } + mmc = init_mmc_device(curr_device); + if (!mmc) + return CMD_RET_FAILURE; - if (IS_SD(mmc)) { - puts("BOOT_BUS_WIDTH only exists on eMMC\n"); - return 1; - } + printf("\nMMC erase: dev # %d, block # %d, count %d ... ", + curr_device, blk, cnt); - /* acknowledge to be sent during boot operation */ - return mmc_set_boot_bus_width(mmc, width, reset, mode); - } else if (strcmp(argv[1], "bootpart-resize") == 0) { - int dev; - struct mmc *mmc; - u32 bootsize, rpmbsize; - - if (argc == 5) { - dev = simple_strtoul(argv[2], NULL, 10); - bootsize = simple_strtoul(argv[3], NULL, 10); - rpmbsize = simple_strtoul(argv[4], NULL, 10); - } else { - return CMD_RET_USAGE; - } + if (mmc_getwp(mmc) == 1) { + printf("Error: card is write protected!\n"); + return CMD_RET_FAILURE; + } + n = mmc->block_dev.block_erase(curr_device, blk, cnt); + printf("%d blocks erased: %s\n", n, (n == cnt) ? "OK" : "ERROR"); - mmc = find_mmc_device(dev); - if (!mmc) { - printf("no mmc device at slot %x\n", dev); - return 1; - } + return (n == cnt) ? CMD_RET_SUCCESS : CMD_RET_FAILURE; +} +static int do_mmc_rescan(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + struct mmc *mmc; - if (IS_SD(mmc)) { - printf("It is not a EMMC device\n"); - return 1; - } + mmc = find_mmc_device(curr_device); + if (!mmc) { + printf("no mmc device at slot %x\n", curr_device); + return CMD_RET_FAILURE; + } - if (0 == mmc_boot_partition_size_change(mmc, - bootsize, rpmbsize)) { - printf("EMMC boot partition Size %d MB\n", bootsize); - printf("EMMC RPMB partition Size %d MB\n", rpmbsize); - return 0; - } else { - printf("EMMC boot partition Size change Failed.\n"); - return 1; - } - } else if (strcmp(argv[1], "rst-function") == 0) { - /* - * Set the RST_n_ENABLE bit of RST_n_FUNCTION - * The only valid values are 0x0, 0x1 and 0x2 and writing - * a value of 0x1 or 0x2 sets the value permanently. - */ - int dev; - struct mmc *mmc; - u8 enable; - - if (argc == 4) { - dev = simple_strtoul(argv[2], NULL, 10); - enable = simple_strtoul(argv[3], NULL, 10); - } else { - return CMD_RET_USAGE; - } + mmc->has_init = 0; - if (enable > 2 || enable < 0) { - puts("Invalid RST_n_ENABLE value\n"); - return CMD_RET_USAGE; - } + if (mmc_init(mmc)) + return CMD_RET_FAILURE; + return CMD_RET_SUCCESS; +} +static int do_mmc_part(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + block_dev_desc_t *mmc_dev; + struct mmc *mmc; - mmc = find_mmc_device(dev); - if (!mmc) { - printf("no mmc device at slot %x\n", dev); - return 1; + mmc = init_mmc_device(curr_device); + if (!mmc) + return CMD_RET_FAILURE; + + mmc_dev = mmc_get_dev(curr_device); + if (mmc_dev != NULL && mmc_dev->type != DEV_TYPE_UNKNOWN) { + print_part(mmc_dev); + return CMD_RET_SUCCESS; + } + + puts("get mmc type error!\n"); + return CMD_RET_FAILURE; +} +static int do_mmc_dev(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + int dev, part = -1, ret; + struct mmc *mmc; + + if (argc == 1) { + dev = curr_device; + } else if (argc == 2) { + dev = simple_strtoul(argv[1], NULL, 10); + } else if (argc == 3) { + dev = (int)simple_strtoul(argv[1], NULL, 10); + part = (int)simple_strtoul(argv[2], NULL, 10); + if (part > PART_ACCESS_MASK) { + printf("#part_num shouldn't be larger than %d\n", + PART_ACCESS_MASK); + return CMD_RET_FAILURE; } + } else { + return CMD_RET_USAGE; + } + + mmc = init_mmc_device(dev); + if (!mmc) + return CMD_RET_FAILURE; - if (IS_SD(mmc)) { - puts("RST_n_FUNCTION only exists on eMMC\n"); + if (part != -1) { + ret = mmc_select_hwpart(dev, part); + printf("switch to partitions #%d, %s\n", + part, (!ret) ? "OK" : "ERROR"); + if (ret) return 1; - } + } + curr_device = dev; + if (mmc->part_config == MMCPART_NOAVAILABLE) + printf("mmc%d is current device\n", curr_device); + else + printf("mmc%d(part %d) is current device\n", + curr_device, mmc->part_num); - return mmc_set_rst_n_function(mmc, enable); -#endif /* CONFIG_SUPPORT_EMMC_BOOT */ + return CMD_RET_SUCCESS; +} +static int do_mmc_list(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + print_mmc_devices('\n'); + return CMD_RET_SUCCESS; +} +#ifdef CONFIG_SUPPORT_EMMC_BOOT +static int do_mmc_bootbus(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + int dev; + struct mmc *mmc; + u8 width, reset, mode; + + if (argc != 5) + return CMD_RET_USAGE; + dev = simple_strtoul(argv[1], NULL, 10); + width = simple_strtoul(argv[2], NULL, 10); + reset = simple_strtoul(argv[3], NULL, 10); + mode = simple_strtoul(argv[4], NULL, 10); + + mmc = init_mmc_device(dev); + if (!mmc) + return CMD_RET_FAILURE; + + if (IS_SD(mmc)) { + puts("BOOT_BUS_WIDTH only exists on eMMC\n"); + return CMD_RET_FAILURE; } - else if (argc == 3 && strcmp(argv[1], "setdsr") == 0) { - struct mmc *mmc = find_mmc_device(curr_device); - u32 val = simple_strtoul(argv[2], NULL, 16); - int ret; + /* acknowledge to be sent during boot operation */ + return mmc_set_boot_bus_width(mmc, width, reset, mode); +} +static int do_mmc_boot_resize(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + int dev; + struct mmc *mmc; + u32 bootsize, rpmbsize; + + if (argc != 4) + return CMD_RET_USAGE; + dev = simple_strtoul(argv[1], NULL, 10); + bootsize = simple_strtoul(argv[2], NULL, 10); + rpmbsize = simple_strtoul(argv[3], NULL, 10); - if (!mmc) { - printf("no mmc device at slot %x\n", curr_device); - return 1; - } - ret = mmc_set_dsr(mmc, val); - printf("set dsr %s\n", (!ret) ? "OK, force rescan" : "ERROR"); - if (!ret) { - mmc->has_init = 0; - if (mmc_init(mmc)) - return 1; - else - return 0; - } - return ret; + mmc = init_mmc_device(dev); + if (!mmc) + return CMD_RET_FAILURE; + + if (IS_SD(mmc)) { + printf("It is not a EMMC device\n"); + return CMD_RET_FAILURE; } - state = MMC_INVALID; - if (argc == 5 && strcmp(argv[1], "read") == 0) - state = MMC_READ; - else if (argc == 5 && strcmp(argv[1], "write") == 0) - state = MMC_WRITE; - else if (argc == 4 && strcmp(argv[1], "erase") == 0) - state = MMC_ERASE; - - if (state != MMC_INVALID) { - struct mmc *mmc = find_mmc_device(curr_device); - int idx = 2; - u32 blk, cnt, n; - void *addr; - - if (state != MMC_ERASE) { - addr = (void *)simple_strtoul(argv[idx], NULL, 16); - ++idx; - } else - addr = NULL; - blk = simple_strtoul(argv[idx], NULL, 16); - cnt = simple_strtoul(argv[idx + 1], NULL, 16); - - if (!mmc) { - printf("no mmc device at slot %x\n", curr_device); - return 1; - } + if (mmc_boot_partition_size_change(mmc, bootsize, rpmbsize)) { + printf("EMMC boot partition Size change Failed.\n"); + return CMD_RET_FAILURE; + } + + printf("EMMC boot partition Size %d MB\n", bootsize); + printf("EMMC RPMB partition Size %d MB\n", rpmbsize); + return CMD_RET_SUCCESS; +} +static int do_mmc_partconf(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + int dev; + struct mmc *mmc; + u8 ack, part_num, access; - printf("\nMMC %s: dev # %d, block # %d, count %d ... ", - argv[1], curr_device, blk, cnt); + if (argc != 5) + return CMD_RET_USAGE; - mmc_init(mmc); + dev = simple_strtoul(argv[1], NULL, 10); + ack = simple_strtoul(argv[2], NULL, 10); + part_num = simple_strtoul(argv[3], NULL, 10); + access = simple_strtoul(argv[4], NULL, 10); - if ((state == MMC_WRITE || state == MMC_ERASE)) { - if (mmc_getwp(mmc) == 1) { - printf("Error: card is write protected!\n"); - return 1; - } - } + mmc = init_mmc_device(dev); + if (!mmc) + return CMD_RET_FAILURE; - switch (state) { - case MMC_READ: - n = mmc->block_dev.block_read(curr_device, blk, - cnt, addr); - /* flush cache after read */ - flush_cache((ulong)addr, cnt * 512); /* FIXME */ - break; - case MMC_WRITE: - n = mmc->block_dev.block_write(curr_device, blk, - cnt, addr); - break; - case MMC_ERASE: - n = mmc->block_dev.block_erase(curr_device, blk, cnt); - break; - default: - BUG(); - } + if (IS_SD(mmc)) { + puts("PARTITION_CONFIG only exists on eMMC\n"); + return CMD_RET_FAILURE; + } + + /* acknowledge to be sent during boot operation */ + return mmc_set_part_conf(mmc, ack, part_num, access); +} +static int do_mmc_rst_func(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + int dev; + struct mmc *mmc; + u8 enable; + + /* + * Set the RST_n_ENABLE bit of RST_n_FUNCTION + * The only valid values are 0x0, 0x1 and 0x2 and writing + * a value of 0x1 or 0x2 sets the value permanently. + */ + if (argc != 3) + return CMD_RET_USAGE; + + dev = simple_strtoul(argv[1], NULL, 10); + enable = simple_strtoul(argv[2], NULL, 10); + + if (enable > 2 || enable < 0) { + puts("Invalid RST_n_ENABLE value\n"); + return CMD_RET_USAGE; + } + + mmc = init_mmc_device(dev); + if (!mmc) + return CMD_RET_FAILURE; + + if (IS_SD(mmc)) { + puts("RST_n_FUNCTION only exists on eMMC\n"); + return CMD_RET_FAILURE; + } - printf("%d blocks %s: %s\n", - n, argv[1], (n == cnt) ? "OK" : "ERROR"); - return (n == cnt) ? 0 : 1; + return mmc_set_rst_n_function(mmc, enable); +} +#endif +static int do_mmc_setdsr(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + struct mmc *mmc; + u32 val; + int ret; + + if (argc != 2) + return CMD_RET_USAGE; + val = simple_strtoul(argv[2], NULL, 16); + + mmc = find_mmc_device(curr_device); + if (!mmc) { + printf("no mmc device at slot %x\n", curr_device); + return CMD_RET_FAILURE; + } + ret = mmc_set_dsr(mmc, val); + printf("set dsr %s\n", (!ret) ? "OK, force rescan" : "ERROR"); + if (!ret) { + mmc->has_init = 0; + if (mmc_init(mmc)) + return CMD_RET_FAILURE; + else + return CMD_RET_SUCCESS; } + return ret; +} + +static cmd_tbl_t cmd_mmc[] = { + U_BOOT_CMD_MKENT(info, 1, 0, do_mmcinfo, "", ""), + U_BOOT_CMD_MKENT(read, 4, 1, do_mmc_read, "", ""), + U_BOOT_CMD_MKENT(write, 4, 0, do_mmc_write, "", ""), + U_BOOT_CMD_MKENT(erase, 3, 0, do_mmc_erase, "", ""), + U_BOOT_CMD_MKENT(rescan, 1, 1, do_mmc_rescan, "", ""), + U_BOOT_CMD_MKENT(part, 1, 1, do_mmc_part, "", ""), + U_BOOT_CMD_MKENT(dev, 3, 0, do_mmc_dev, "", ""), + U_BOOT_CMD_MKENT(list, 1, 1, do_mmc_list, "", ""), +#ifdef CONFIG_SUPPORT_EMMC_BOOT + U_BOOT_CMD_MKENT(bootbus, 5, 0, do_mmc_bootbus, "", ""), + U_BOOT_CMD_MKENT(bootpart-resize, 3, 0, do_mmc_boot_resize, "", ""), + U_BOOT_CMD_MKENT(partconf, 5, 0, do_mmc_partconf, "", ""), + U_BOOT_CMD_MKENT(rst-function, 3, 0, do_mmc_rst_func, "", ""), +#endif +#ifdef CONFIG_SUPPORT_EMMC_RPMB + U_BOOT_CMD_MKENT(rpmb, CONFIG_SYS_MAXARGS, 1, do_mmcrpmb, "", ""), +#endif + U_BOOT_CMD_MKENT(setdsr, 2, 0, do_mmc_setdsr, "", ""), +}; + +static int do_mmcops(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + cmd_tbl_t *cp; + + cp = find_cmd_tbl(argv[1], cmd_mmc, ARRAY_SIZE(cmd_mmc)); + + /* Drop the mmc command */ + argc--; + argv++; + + if (cp == NULL || argc > cp->maxargs) + return CMD_RET_USAGE; + if (flag == CMD_FLAG_REPEAT && !cp->repeatable) + return CMD_RET_SUCCESS; - return CMD_RET_USAGE; + if (curr_device < 0) { + if (get_mmc_num() > 0) { + curr_device = 0; + } else { + puts("No MMC device available\n"); + return CMD_RET_FAILURE; + } + } + return cp->cmd(cmdtp, flag, argc, argv); } U_BOOT_CMD( - mmc, 6, 1, do_mmcops, + mmc, 7, 1, do_mmcops, "MMC sub system", - "read addr blk# cnt\n" + "info - display info of the current MMC device\n" + "mmc read addr blk# cnt\n" "mmc write addr blk# cnt\n" "mmc erase blk# cnt\n" "mmc rescan\n" @@ -474,6 +665,20 @@ U_BOOT_CMD( " - Change the RST_n_FUNCTION field of the specified device\n" " WARNING: This is a write-once field and 0 / 1 / 2 are the only valid values.\n" #endif - "mmc setdsr - set DSR register value\n" +#ifdef CONFIG_SUPPORT_EMMC_RPMB + "mmc rpmb read addr blk# cnt [address of auth-key] - block size is 256 bytes\n" + "mmc rpmb write addr blk# cnt <address of auth-key> - block size is 256 bytes\n" + "mmc rpmb key <address of auth-key> - program the RPMB authentication key.\n" + "mmc rpmb counter - read the value of the write counter\n" +#endif + "mmc setdsr <value> - set DSR register value\n" ); + +/* Old command kept for compatibility. Same as 'mmc info' */ +U_BOOT_CMD( + mmcinfo, 1, 0, do_mmcinfo, + "display MMC info", + "- display info of the current MMC device" +); + #endif /* !CONFIG_GENERIC_MMC */ diff --git a/common/cmd_nand.c b/common/cmd_nand.c index 04ab0f19be..a84f7dc2d1 100644 --- a/common/cmd_nand.c +++ b/common/cmd_nand.c @@ -605,22 +605,16 @@ static int do_nand(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) opts.spread = spread; if (scrub) { - if (!scrub_yes) - puts(scrub_warn); - - if (scrub_yes) + if (scrub_yes) { opts.scrub = 1; - else if (getc() == 'y') { - puts("y"); - if (getc() == '\r') + } else { + puts(scrub_warn); + if (confirm_yesno()) { opts.scrub = 1; - else { + } else { puts("scrub aborted\n"); return 1; } - } else { - puts("scrub aborted\n"); - return 1; } } ret = nand_erase_opts(nand, &opts); diff --git a/common/cmd_otp.c b/common/cmd_otp.c index 67808aa377..593bb8c650 100644 --- a/common/cmd_otp.c +++ b/common/cmd_otp.c @@ -158,21 +158,9 @@ int do_otp(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) lowup(half + count - 1), page + (half + count - 1) / 2, half + count ); - - i = 0; - while (1) { - if (tstc()) { - const char exp_ans[] = "YES\r"; - char c; - putc(c = getc()); - if (exp_ans[i++] != c) { - printf(" Aborting\n"); - return 1; - } else if (!exp_ans[i]) { - puts("\n"); - break; - } - } + if (!confirm_yesno()) { + printf(" Aborting\n"); + return 1; } } diff --git a/common/cmd_part.c b/common/cmd_part.c index 14248548d9..c84bc27b40 100644 --- a/common/cmd_part.c +++ b/common/cmd_part.c @@ -82,7 +82,7 @@ int do_part(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) U_BOOT_CMD( part, 5, 1, do_part, "disk partition related commands", - "uuid <interface> <dev>:<part>\n" + "part uuid <interface> <dev>:<part>\n" " - print partition UUID\n" "part uuid <interface> <dev>:<part> <varname>\n" " - set environment variable to partition UUID\n" diff --git a/common/cmd_usb_mass_storage.c b/common/cmd_usb_mass_storage.c index d8d9efd4f6..2c879ea083 100644 --- a/common/cmd_usb_mass_storage.c +++ b/common/cmd_usb_mass_storage.c @@ -9,41 +9,107 @@ #include <common.h> #include <command.h> #include <g_dnl.h> +#include <part.h> #include <usb.h> #include <usb_mass_storage.h> +static int ums_read_sector(struct ums *ums_dev, + ulong start, lbaint_t blkcnt, void *buf) +{ + block_dev_desc_t *block_dev = ums_dev->block_dev; + lbaint_t blkstart = start + ums_dev->start_sector; + int dev_num = block_dev->dev; + + return block_dev->block_read(dev_num, blkstart, blkcnt, buf); +} + +static int ums_write_sector(struct ums *ums_dev, + ulong start, lbaint_t blkcnt, const void *buf) +{ + block_dev_desc_t *block_dev = ums_dev->block_dev; + lbaint_t blkstart = start + ums_dev->start_sector; + int dev_num = block_dev->dev; + + return block_dev->block_write(dev_num, blkstart, blkcnt, buf); +} + +static struct ums ums_dev = { + .read_sector = ums_read_sector, + .write_sector = ums_write_sector, + .name = "UMS disk", +}; + +struct ums *ums_init(const char *devtype, const char *devnum) +{ + block_dev_desc_t *block_dev; + int ret; + + ret = get_device(devtype, devnum, &block_dev); + if (ret < 0) + return NULL; + + /* f_mass_storage.c assumes SECTOR_SIZE sectors */ + if (block_dev->blksz != SECTOR_SIZE) + return NULL; + + ums_dev.block_dev = block_dev; + ums_dev.start_sector = 0; + ums_dev.num_sectors = block_dev->lba; + + printf("UMS: disk start sector: %#x, count: %#x\n", + ums_dev.start_sector, ums_dev.num_sectors); + + return &ums_dev; +} + int do_usb_mass_storage(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { + const char *usb_controller; + const char *devtype; + const char *devnum; + struct ums *ums; + unsigned int controller_index; + int rc; + int cable_ready_timeout __maybe_unused; + if (argc < 3) return CMD_RET_USAGE; - const char *usb_controller = argv[1]; - const char *mmc_devstring = argv[2]; - - unsigned int dev_num = simple_strtoul(mmc_devstring, NULL, 0); + usb_controller = argv[1]; + if (argc >= 4) { + devtype = argv[2]; + devnum = argv[3]; + } else { + devtype = "mmc"; + devnum = argv[2]; + } - struct ums *ums = ums_init(dev_num); + ums = ums_init(devtype, devnum); if (!ums) return CMD_RET_FAILURE; - unsigned int controller_index = (unsigned int)(simple_strtoul( - usb_controller, NULL, 0)); + controller_index = (unsigned int)(simple_strtoul( + usb_controller, NULL, 0)); if (board_usb_init(controller_index, USB_INIT_DEVICE)) { error("Couldn't init USB controller."); return CMD_RET_FAILURE; } - int rc = fsg_init(ums); + rc = fsg_init(ums); if (rc) { error("fsg_init failed"); return CMD_RET_FAILURE; } - g_dnl_register("usb_dnl_ums"); + rc = g_dnl_register("usb_dnl_ums"); + if (rc) { + error("g_dnl_register failed"); + return CMD_RET_FAILURE; + } /* Timeout unit: seconds */ - int cable_ready_timeout = UMS_CABLE_READY_TIMEOUT; + cable_ready_timeout = UMS_CABLE_READY_TIMEOUT; if (!g_dnl_board_usb_cable_connected()) { /* @@ -91,7 +157,8 @@ exit: return CMD_RET_SUCCESS; } -U_BOOT_CMD(ums, CONFIG_SYS_MAXARGS, 1, do_usb_mass_storage, +U_BOOT_CMD(ums, 4, 1, do_usb_mass_storage, "Use the UMS [User Mass Storage]", - "ums <USB_controller> <mmc_dev> e.g. ums 0 0" + "ums <USB_controller> [<devtype>] <devnum> e.g. ums 0 mmc 0\n" + " devtype defaults to mmc" ); diff --git a/common/console.c b/common/console.c index 2dfb788885..5453726f69 100644 --- a/common/console.c +++ b/common/console.c @@ -537,7 +537,33 @@ int ctrlc(void) } return 0; } - +/* Reads user's confirmation. + Returns 1 if user's input is "y", "Y", "yes" or "YES" +*/ +int confirm_yesno(void) +{ + int i; + char str_input[5]; + + /* Flush input */ + while (tstc()) + getc(); + i = 0; + while (i < sizeof(str_input)) { + str_input[i] = getc(); + putc(str_input[i]); + if (str_input[i] == '\r') + break; + i++; + } + putc('\n'); + if (strncmp(str_input, "y\r", 2) == 0 || + strncmp(str_input, "Y\r", 2) == 0 || + strncmp(str_input, "yes\r", 4) == 0 || + strncmp(str_input, "YES\r", 4) == 0) + return 1; + return 0; +} /* pass 1 to disable ctrlc() checking, 0 to enable. * returns previous state */ diff --git a/common/image-android.c b/common/image-android.c new file mode 100644 index 0000000000..6ded7e2c97 --- /dev/null +++ b/common/image-android.c @@ -0,0 +1,84 @@ +/* + * Copyright (c) 2011 Sebastian Andrzej Siewior <bigeasy@linutronix.de> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <image.h> +#include <android_image.h> + +static char andr_tmp_str[ANDR_BOOT_ARGS_SIZE + 1]; + +int android_image_get_kernel(const struct andr_img_hdr *hdr, int verify, + ulong *os_data, ulong *os_len) +{ + /* + * Not all Android tools use the id field for signing the image with + * sha1 (or anything) so we don't check it. It is not obvious that the + * string is null terminated so we take care of this. + */ + strncpy(andr_tmp_str, hdr->name, ANDR_BOOT_NAME_SIZE); + andr_tmp_str[ANDR_BOOT_NAME_SIZE] = '\0'; + if (strlen(andr_tmp_str)) + printf("Android's image name: %s\n", andr_tmp_str); + + printf("Kernel load addr 0x%08x size %u KiB\n", + hdr->kernel_addr, DIV_ROUND_UP(hdr->kernel_size, 1024)); + strncpy(andr_tmp_str, hdr->cmdline, ANDR_BOOT_ARGS_SIZE); + andr_tmp_str[ANDR_BOOT_ARGS_SIZE] = '\0'; + if (strlen(andr_tmp_str)) { + printf("Kernel command line: %s\n", andr_tmp_str); + setenv("bootargs", andr_tmp_str); + } + if (hdr->ramdisk_size) + printf("RAM disk load addr 0x%08x size %u KiB\n", + hdr->ramdisk_addr, + DIV_ROUND_UP(hdr->ramdisk_size, 1024)); + + if (os_data) { + *os_data = (ulong)hdr; + *os_data += hdr->page_size; + } + if (os_len) + *os_len = hdr->kernel_size; + return 0; +} + +int android_image_check_header(const struct andr_img_hdr *hdr) +{ + return memcmp(ANDR_BOOT_MAGIC, hdr->magic, ANDR_BOOT_MAGIC_SIZE); +} + +ulong android_image_get_end(const struct andr_img_hdr *hdr) +{ + u32 size = 0; + /* + * The header takes a full page, the remaining components are aligned + * on page boundary + */ + size += hdr->page_size; + size += ALIGN(hdr->kernel_size, hdr->page_size); + size += ALIGN(hdr->ramdisk_size, hdr->page_size); + size += ALIGN(hdr->second_size, hdr->page_size); + + return size; +} + +ulong android_image_get_kload(const struct andr_img_hdr *hdr) +{ + return hdr->kernel_addr; +} + +int android_image_get_ramdisk(const struct andr_img_hdr *hdr, + ulong *rd_data, ulong *rd_len) +{ + if (!hdr->ramdisk_size) + return -1; + *rd_data = (unsigned long)hdr; + *rd_data += hdr->page_size; + *rd_data += ALIGN(hdr->kernel_size, hdr->page_size); + + *rd_len = hdr->ramdisk_size; + return 0; +} diff --git a/common/image.c b/common/image.c index fcc5a9c3e1..fa4864d24c 100644 --- a/common/image.c +++ b/common/image.c @@ -660,10 +660,12 @@ int genimg_get_format(const void *img_addr) if (image_check_magic(hdr)) format = IMAGE_FORMAT_LEGACY; #if defined(CONFIG_FIT) || defined(CONFIG_OF_LIBFDT) - else { - if (fdt_check_header(img_addr) == 0) - format = IMAGE_FORMAT_FIT; - } + else if (fdt_check_header(img_addr) == 0) + format = IMAGE_FORMAT_FIT; +#endif +#ifdef CONFIG_ANDROID_BOOT_IMAGE + else if (android_image_check_header(img_addr) == 0) + format = IMAGE_FORMAT_ANDROID; #endif return format; @@ -933,7 +935,15 @@ int boot_get_ramdisk(int argc, char * const argv[], bootm_headers_t *images, (ulong)images->legacy_hdr_os); image_multi_getimg(images->legacy_hdr_os, 1, &rd_data, &rd_len); - } else { + } +#ifdef CONFIG_ANDROID_BOOT_IMAGE + else if ((genimg_get_format(images) == IMAGE_FORMAT_ANDROID) && + (!android_image_get_ramdisk((void *)images->os.start, + &rd_data, &rd_len))) { + /* empty */ + } +#endif + else { /* * no initrd image */ diff --git a/common/spl/spl_nand.c b/common/spl/spl_nand.c index 9da021862e..062461b2b6 100644 --- a/common/spl/spl_nand.c +++ b/common/spl/spl_nand.c @@ -76,7 +76,7 @@ void spl_nand_load_image(void) #endif /* Load u-boot */ nand_spl_load_image(CONFIG_SYS_NAND_U_BOOT_OFFS, - CONFIG_SYS_NAND_PAGE_SIZE, (void *)header); + sizeof(*header), (void *)header); spl_parse_image_header(header); nand_spl_load_image(CONFIG_SYS_NAND_U_BOOT_OFFS, spl_image.size, (void *)spl_image.load_addr); diff --git a/disk/part.c b/disk/part.c index b8c6aac801..2827089d8d 100644 --- a/disk/part.c +++ b/disk/part.c @@ -22,6 +22,7 @@ struct block_drvr { char *name; block_dev_desc_t* (*get_dev)(int dev); + int (*select_hwpart)(int dev_num, int hwpart); }; static const struct block_drvr block_drvr[] = { @@ -38,7 +39,11 @@ static const struct block_drvr block_drvr[] = { { .name = "usb", .get_dev = usb_stor_get_dev, }, #endif #if defined(CONFIG_MMC) - { .name = "mmc", .get_dev = mmc_get_dev, }, + { + .name = "mmc", + .get_dev = mmc_get_dev, + .select_hwpart = mmc_select_hwpart, + }, #endif #if defined(CONFIG_SYSTEMACE) { .name = "ace", .get_dev = systemace_get_dev, }, @@ -52,11 +57,13 @@ static const struct block_drvr block_drvr[] = { DECLARE_GLOBAL_DATA_PTR; #ifdef HAVE_BLOCK_DEVICE -block_dev_desc_t *get_dev(const char *ifname, int dev) +block_dev_desc_t *get_dev_hwpart(const char *ifname, int dev, int hwpart) { const struct block_drvr *drvr = block_drvr; block_dev_desc_t* (*reloc_get_dev)(int dev); + int (*select_hwpart)(int dev_num, int hwpart); char *name; + int ret; if (!ifname) return NULL; @@ -68,17 +75,41 @@ block_dev_desc_t *get_dev(const char *ifname, int dev) while (drvr->name) { name = drvr->name; reloc_get_dev = drvr->get_dev; + select_hwpart = drvr->select_hwpart; #ifdef CONFIG_NEEDS_MANUAL_RELOC name += gd->reloc_off; reloc_get_dev += gd->reloc_off; -#endif - if (strncmp(ifname, name, strlen(name)) == 0) - return reloc_get_dev(dev); + if (select_hwpart) + select_hwpart += gd->reloc_off; +#endif + if (strncmp(ifname, name, strlen(name)) == 0) { + block_dev_desc_t *dev_desc = reloc_get_dev(dev); + if (!dev_desc) + return NULL; + if (hwpart == -1) + return dev_desc; + if (!select_hwpart) + return NULL; + ret = select_hwpart(dev_desc->dev, hwpart); + if (ret < 0) + return NULL; + return dev_desc; + } drvr++; } return NULL; } + +block_dev_desc_t *get_dev(const char *ifname, int dev) +{ + return get_dev_hwpart(ifname, dev, -1); +} #else +block_dev_desc_t *get_dev_hwpart(const char *ifname, int dev, int hwpart) +{ + return NULL; +} + block_dev_desc_t *get_dev(const char *ifname, int dev) { return NULL; @@ -413,25 +444,52 @@ int get_partition_info(block_dev_desc_t *dev_desc, int part return -1; } -int get_device(const char *ifname, const char *dev_str, +int get_device(const char *ifname, const char *dev_hwpart_str, block_dev_desc_t **dev_desc) { char *ep; - int dev; + char *dup_str = NULL; + const char *dev_str, *hwpart_str; + int dev, hwpart; + + hwpart_str = strchr(dev_hwpart_str, '.'); + if (hwpart_str) { + dup_str = strdup(dev_hwpart_str); + dup_str[hwpart_str - dev_hwpart_str] = 0; + dev_str = dup_str; + hwpart_str++; + } else { + dev_str = dev_hwpart_str; + hwpart = -1; + } dev = simple_strtoul(dev_str, &ep, 16); if (*ep) { printf("** Bad device specification %s %s **\n", ifname, dev_str); - return -1; + dev = -1; + goto cleanup; + } + + if (hwpart_str) { + hwpart = simple_strtoul(hwpart_str, &ep, 16); + if (*ep) { + printf("** Bad HW partition specification %s %s **\n", + ifname, hwpart_str); + dev = -1; + goto cleanup; + } } - *dev_desc = get_dev(ifname, dev); + *dev_desc = get_dev_hwpart(ifname, dev, hwpart); if (!(*dev_desc) || ((*dev_desc)->type == DEV_TYPE_UNKNOWN)) { - printf("** Bad device %s %s **\n", ifname, dev_str); - return -1; + printf("** Bad device %s %s **\n", ifname, dev_hwpart_str); + dev = -1; + goto cleanup; } +cleanup: + free(dup_str); return dev; } diff --git a/doc/README.android-fastboot b/doc/README.android-fastboot new file mode 100644 index 0000000000..f1d128caa9 --- /dev/null +++ b/doc/README.android-fastboot @@ -0,0 +1,91 @@ +Android Fastboot +~~~~~~~~~~~~~~~~ + +Overview +======== +The protocol that is used over USB is described in +README.android-fastboot-protocol in same directory. + +The current implementation does not yet support the flash and erase +commands. + +Client installation +=================== +The counterpart to this gadget is the fastboot client which can +be found in Android's platform/system/core repository in the fastboot +folder. It runs on Windows, Linux and even OSX. Linux user are lucky since +they only need libusb. +Windows users need to bring some time until they have Android SDK (currently +http://dl.google.com/android/installer_r12-windows.exe) installed. You +need to install ADB package which contains the required glue libraries for +accessing USB. Also you need "Google USB driver package" and "SDK platform +tools". Once installed the usb driver is placed in your SDK folder under +extras\google\usb_driver. The android_winusb.inf needs a line like + + %SingleBootLoaderInterface% = USB_Install, USB\VID_0451&PID_D022 + +either in the [Google.NTx86] section for 32bit Windows or [Google.NTamd64] +for 64bit Windows. VID and PID should match whatever the fastboot is +advertising. + +Board specific +============== +The fastboot gadget relies on the USB download gadget, so the following +options must be configured: + +CONFIG_USBDOWNLOAD_GADGET +CONFIG_G_DNL_VENDOR_NUM +CONFIG_G_DNL_PRODUCT_NUM +CONFIG_G_DNL_MANUFACTURER + +The fastboot function is enabled by defining CONFIG_CMD_FASTBOOT and +CONFIG_ANDROID_BOOT_IMAGE. + +The fastboot protocol requires a large memory buffer for downloads. This +buffer should be as large as possible for a platform. The location of the +buffer and size are set with CONFIG_USB_FASTBOOT_BUF_ADDR and +CONFIG_USB_FASTBOOT_BUF_SIZE. + +In Action +========= +Enter into fastboot by executing the fastboot command in u-boot and you +should see: +|GADGET DRIVER: usb_dnl_fastboot + +On the client side you can fetch the bootloader version for instance: +|>fastboot getvar bootloader-version +|bootloader-version: U-Boot 2014.04-00005-gd24cabc +|finished. total time: 0.000s + +or initiate a reboot: +|>fastboot reboot + +and once the client comes back, the board should reset. + +You can also specify a kernel image to boot. You have to either specify +the an image in Android format _or_ pass a binary kernel and let the +fastboot client wrap the Android suite around it. On OMAP for instance you +take zImage kernel and pass it to the fastboot client: + +|>fastboot -b 0x80000000 -c "console=ttyO2 earlyprintk root=/dev/ram0 +| mem=128M" boot zImage +|creating boot image... +|creating boot image - 1847296 bytes +|downloading 'boot.img'... +|OKAY [ 2.766s] +|booting... +|OKAY [ -0.000s] +|finished. total time: 2.766s + +and on the gadget side you should see: +|Starting download of 1847296 bytes +|........................................................ +|downloading of 1847296 bytes finished +|Booting kernel.. +|## Booting Android Image at 0x81000000 ... +|Kernel load addr 0x80008000 size 1801 KiB +|Kernel command line: console=ttyO2 earlyprintk root=/dev/ram0 mem=128M +| Loading Kernel Image ... OK +|OK +| +|Starting kernel ... diff --git a/doc/README.android-fastboot-protocol b/doc/README.android-fastboot-protocol new file mode 100644 index 0000000000..e9e7166a26 --- /dev/null +++ b/doc/README.android-fastboot-protocol @@ -0,0 +1,170 @@ +FastBoot Version 0.4 +---------------------- + +The fastboot protocol is a mechanism for communicating with bootloaders +over USB. It is designed to be very straightforward to implement, to +allow it to be used across a wide range of devices and from hosts running +Linux, Windows, or OSX. + + +Basic Requirements +------------------ + +* Two bulk endpoints (in, out) are required +* Max packet size must be 64 bytes for full-speed and 512 bytes for + high-speed USB +* The protocol is entirely host-driven and synchronous (unlike the + multi-channel, bi-directional, asynchronous ADB protocol) + + +Transport and Framing +--------------------- + +1. Host sends a command, which is an ascii string in a single + packet no greater than 64 bytes. + +2. Client response with a single packet no greater than 64 bytes. + The first four bytes of the response are "OKAY", "FAIL", "DATA", + or "INFO". Additional bytes may contain an (ascii) informative + message. + + a. INFO -> the remaining 60 bytes are an informative message + (providing progress or diagnostic messages). They should + be displayed and then step #2 repeats + + b. FAIL -> the requested command failed. The remaining 60 bytes + of the response (if present) provide a textual failure message + to present to the user. Stop. + + c. OKAY -> the requested command completed successfully. Go to #5 + + d. DATA -> the requested command is ready for the data phase. + A DATA response packet will be 12 bytes long, in the form of + DATA00000000 where the 8 digit hexidecimal number represents + the total data size to transfer. + +3. Data phase. Depending on the command, the host or client will + send the indicated amount of data. Short packets are always + acceptable and zero-length packets are ignored. This phase continues + until the client has sent or received the number of bytes indicated + in the "DATA" response above. + +4. Client responds with a single packet no greater than 64 bytes. + The first four bytes of the response are "OKAY", "FAIL", or "INFO". + Similar to #2: + + a. INFO -> display the remaining 60 bytes and return to #4 + + b. FAIL -> display the remaining 60 bytes (if present) as a failure + reason and consider the command failed. Stop. + + c. OKAY -> success. Go to #5 + +5. Success. Stop. + + +Example Session +--------------- + +Host: "getvar:version" request version variable + +Client: "OKAY0.4" return version "0.4" + +Host: "getvar:nonexistant" request some undefined variable + +Client: "OKAY" return value "" + +Host: "download:00001234" request to send 0x1234 bytes of data + +Client: "DATA00001234" ready to accept data + +Host: < 0x1234 bytes > send data + +Client: "OKAY" success + +Host: "flash:bootloader" request to flash the data to the bootloader + +Client: "INFOerasing flash" indicate status / progress + "INFOwriting flash" + "OKAY" indicate success + +Host: "powerdown" send a command + +Client: "FAILunknown command" indicate failure + + +Command Reference +----------------- + +* Command parameters are indicated by printf-style escape sequences. + +* Commands are ascii strings and sent without the quotes (which are + for illustration only here) and without a trailing 0 byte. + +* Commands that begin with a lowercase letter are reserved for this + specification. OEM-specific commands should not begin with a + lowercase letter, to prevent incompatibilities with future specs. + + "getvar:%s" Read a config/version variable from the bootloader. + The variable contents will be returned after the + OKAY response. + + "download:%08x" Write data to memory which will be later used + by "boot", "ramdisk", "flash", etc. The client + will reply with "DATA%08x" if it has enough + space in RAM or "FAIL" if not. The size of + the download is remembered. + + "verify:%08x" Send a digital signature to verify the downloaded + data. Required if the bootloader is "secure" + otherwise "flash" and "boot" will be ignored. + + "flash:%s" Write the previously downloaded image to the + named partition (if possible). + + "erase:%s" Erase the indicated partition (clear to 0xFFs) + + "boot" The previously downloaded data is a boot.img + and should be booted according to the normal + procedure for a boot.img + + "continue" Continue booting as normal (if possible) + + "reboot" Reboot the device. + + "reboot-bootloader" Reboot back into the bootloader. + Useful for upgrade processes that require upgrading + the bootloader and then upgrading other partitions + using the new bootloader. + + "powerdown" Power off the device. + + + +Client Variables +---------------- + +The "getvar:%s" command is used to read client variables which +represent various information about the device and the software +on it. + +The various currently defined names are: + + version Version of FastBoot protocol supported. + It should be "0.3" for this document. + + version-bootloader Version string for the Bootloader. + + version-baseband Version string of the Baseband Software + + product Name of the product + + serialno Product serial number + + secure If the value is "yes", this is a secure + bootloader requiring a signature before + it will install or boot images. + +Names starting with a lowercase character are reserved by this +specification. OEM-specific names should not start with lowercase +characters. diff --git a/drivers/dfu/dfu.c b/drivers/dfu/dfu.c index 51b10263b8..a93810934a 100644 --- a/drivers/dfu/dfu.c +++ b/drivers/dfu/dfu.c @@ -131,6 +131,10 @@ int dfu_flush(struct dfu_entity *dfu, void *buf, int size, int blk_seq_num) { int ret = 0; + ret = dfu_write_buffer_drain(dfu); + if (ret) + return ret; + if (dfu->flush_medium) ret = dfu->flush_medium(dfu); diff --git a/drivers/dfu/dfu_mmc.c b/drivers/dfu/dfu_mmc.c index 5e10ea7e66..63cc876612 100644 --- a/drivers/dfu/dfu_mmc.c +++ b/drivers/dfu/dfu_mmc.c @@ -18,11 +18,29 @@ static unsigned char __aligned(CONFIG_SYS_CACHELINE_SIZE) dfu_file_buf[CONFIG_SYS_DFU_MAX_FILE_SIZE]; static long dfu_file_buf_len; +static int mmc_access_part(struct dfu_entity *dfu, struct mmc *mmc, int part) +{ + int ret; + + if (part == mmc->part_num) + return 0; + + ret = mmc_switch_part(dfu->dev_num, part); + if (ret) { + error("Cannot switch to partition %d\n", part); + return ret; + } + mmc->part_num = part; + + return 0; +} + static int mmc_block_op(enum dfu_op op, struct dfu_entity *dfu, u64 offset, void *buf, long *len) { struct mmc *mmc = find_mmc_device(dfu->dev_num); u32 blk_start, blk_count, n = 0; + int ret, part_num_bkp = 0; /* * We must ensure that we work in lba_blk_size chunks, so ALIGN @@ -39,6 +57,13 @@ static int mmc_block_op(enum dfu_op op, struct dfu_entity *dfu, return -EINVAL; } + if (dfu->data.mmc.hw_partition >= 0) { + part_num_bkp = mmc->part_num; + ret = mmc_access_part(dfu, mmc, dfu->data.mmc.hw_partition); + if (ret) + return ret; + } + debug("%s: %s dev: %d start: %d cnt: %d buf: 0x%p\n", __func__, op == DFU_OP_READ ? "MMC READ" : "MMC WRITE", dfu->dev_num, blk_start, blk_count, buf); @@ -57,9 +82,17 @@ static int mmc_block_op(enum dfu_op op, struct dfu_entity *dfu, if (n != blk_count) { error("MMC operation failed"); + if (dfu->data.mmc.hw_partition >= 0) + mmc_access_part(dfu, mmc, part_num_bkp); return -EIO; } + if (dfu->data.mmc.hw_partition >= 0) { + ret = mmc_access_part(dfu, mmc, part_num_bkp); + if (ret) + return ret; + } + return 0; } @@ -194,6 +227,8 @@ int dfu_read_medium_mmc(struct dfu_entity *dfu, u64 offset, void *buf, * 2nd and 3rd: * lba_start and lba_size, for raw write * mmc_dev and mmc_part, for filesystems and part + * 4th (optional): + * mmcpart <num> (access to HW eMMC partitions) */ int dfu_fill_entity_mmc(struct dfu_entity *dfu, char *s) { @@ -233,11 +268,22 @@ int dfu_fill_entity_mmc(struct dfu_entity *dfu, char *s) return -ENODEV; } + dfu->data.mmc.hw_partition = -EINVAL; if (!strcmp(entity_type, "raw")) { dfu->layout = DFU_RAW_ADDR; dfu->data.mmc.lba_start = second_arg; dfu->data.mmc.lba_size = third_arg; dfu->data.mmc.lba_blk_size = mmc->read_bl_len; + + /* + * Check for an extra entry at dfu_alt_info env variable + * specifying the mmc HW defined partition number + */ + if (s) + if (!strcmp(strsep(&s, " "), "mmcpart")) + dfu->data.mmc.hw_partition = + simple_strtoul(s, NULL, 0); + } else if (!strcmp(entity_type, "part")) { disk_partition_t partinfo; block_dev_desc_t *blk_dev = &mmc->block_dev; diff --git a/drivers/dfu/dfu_nand.c b/drivers/dfu/dfu_nand.c index 2d07097e85..ccdbef6b75 100644 --- a/drivers/dfu/dfu_nand.c +++ b/drivers/dfu/dfu_nand.c @@ -163,6 +163,18 @@ static int dfu_flush_medium_nand(struct dfu_entity *dfu) return ret; } +unsigned int dfu_polltimeout_nand(struct dfu_entity *dfu) +{ + /* + * Currently, Poll Timeout != 0 is only needed on nand + * ubi partition, as the not used sectors need an erase + */ + if (dfu->data.nand.ubi) + return DFU_MANIFEST_POLL_TIMEOUT; + + return DFU_DEFAULT_POLL_TIMEOUT; +} + int dfu_fill_entity_nand(struct dfu_entity *dfu, char *s) { char *st; @@ -211,6 +223,7 @@ int dfu_fill_entity_nand(struct dfu_entity *dfu, char *s) dfu->read_medium = dfu_read_medium_nand; dfu->write_medium = dfu_write_medium_nand; dfu->flush_medium = dfu_flush_medium_nand; + dfu->poll_timeout = dfu_polltimeout_nand; /* initial state */ dfu->inited = 0; diff --git a/drivers/fpga/fpga.c b/drivers/fpga/fpga.c index b940d9b316..37946d5e18 100644 --- a/drivers/fpga/fpga.c +++ b/drivers/fpga/fpga.c @@ -173,16 +173,45 @@ int fpga_add(fpga_type devtype, void *desc) /* * Convert bitstream data and load into the fpga */ -int __weak fpga_loadbitstream(int devnum, char *fpgadata, size_t size) +int __weak fpga_loadbitstream(int devnum, char *fpgadata, size_t size, + bitstream_type bstype) { printf("Bitstream support not implemented for this FPGA device\n"); return FPGA_FAIL; } +#if defined(CONFIG_CMD_FPGA_LOADFS) +int fpga_fsload(int devnum, const void *buf, size_t size, + fpga_fs_info *fpga_fsinfo) +{ + int ret_val = FPGA_FAIL; /* assume failure */ + const fpga_desc *desc = fpga_validate(devnum, buf, size, + (char *)__func__); + + if (desc) { + switch (desc->devtype) { + case fpga_xilinx: +#if defined(CONFIG_FPGA_XILINX) + ret_val = xilinx_loadfs(desc->devdesc, buf, size, + fpga_fsinfo); +#else + fpga_no_sup((char *)__func__, "Xilinx devices"); +#endif + break; + default: + printf("%s: Invalid or unsupported device type %d\n", + __func__, desc->devtype); + } + } + + return ret_val; +} +#endif + /* * Generic multiplexing code */ -int fpga_load(int devnum, const void *buf, size_t bsize) +int fpga_load(int devnum, const void *buf, size_t bsize, bitstream_type bstype) { int ret_val = FPGA_FAIL; /* assume failure */ const fpga_desc *desc = fpga_validate(devnum, buf, bsize, @@ -192,7 +221,8 @@ int fpga_load(int devnum, const void *buf, size_t bsize) switch (desc->devtype) { case fpga_xilinx: #if defined(CONFIG_FPGA_XILINX) - ret_val = xilinx_load(desc->devdesc, buf, bsize); + ret_val = xilinx_load(desc->devdesc, buf, bsize, + bstype); #else fpga_no_sup((char *)__func__, "Xilinx devices"); #endif diff --git a/drivers/fpga/spartan2.c b/drivers/fpga/spartan2.c index 7054056140..859fb3c778 100644 --- a/drivers/fpga/spartan2.c +++ b/drivers/fpga/spartan2.c @@ -41,7 +41,8 @@ static int spartan2_ss_dump(xilinx_desc *desc, const void *buf, size_t bsize); /* ------------------------------------------------------------------------- */ /* Spartan-II Generic Implementation */ -static int spartan2_load(xilinx_desc *desc, const void *buf, size_t bsize) +static int spartan2_load(xilinx_desc *desc, const void *buf, size_t bsize, + bitstream_type bstype) { int ret_val = FPGA_FAIL; diff --git a/drivers/fpga/spartan3.c b/drivers/fpga/spartan3.c index 5c9412c2f6..b0213e6999 100644 --- a/drivers/fpga/spartan3.c +++ b/drivers/fpga/spartan3.c @@ -45,7 +45,8 @@ static int spartan3_ss_dump(xilinx_desc *desc, const void *buf, size_t bsize); /* ------------------------------------------------------------------------- */ /* Spartan-II Generic Implementation */ -static int spartan3_load(xilinx_desc *desc, const void *buf, size_t bsize) +static int spartan3_load(xilinx_desc *desc, const void *buf, size_t bsize, + bitstream_type bstype) { int ret_val = FPGA_FAIL; diff --git a/drivers/fpga/virtex2.c b/drivers/fpga/virtex2.c index e092147edd..0d2d9a4693 100644 --- a/drivers/fpga/virtex2.c +++ b/drivers/fpga/virtex2.c @@ -90,7 +90,8 @@ static int virtex2_ssm_dump(xilinx_desc *desc, const void *buf, size_t bsize); static int virtex2_ss_load(xilinx_desc *desc, const void *buf, size_t bsize); static int virtex2_ss_dump(xilinx_desc *desc, const void *buf, size_t bsize); -static int virtex2_load(xilinx_desc *desc, const void *buf, size_t bsize) +static int virtex2_load(xilinx_desc *desc, const void *buf, size_t bsize, + bitstream_type bstype) { int ret_val = FPGA_FAIL; diff --git a/drivers/fpga/xilinx.c b/drivers/fpga/xilinx.c index 8837f5c122..3795c1aff6 100644 --- a/drivers/fpga/xilinx.c +++ b/drivers/fpga/xilinx.c @@ -24,7 +24,8 @@ static int xilinx_validate(xilinx_desc *desc, char *fn); /* ------------------------------------------------------------------------- */ -int fpga_loadbitstream(int devnum, char *fpgadata, size_t size) +int fpga_loadbitstream(int devnum, char *fpgadata, size_t size, + bitstream_type bstype) { unsigned int length; unsigned int swapsize; @@ -127,19 +128,36 @@ int fpga_loadbitstream(int devnum, char *fpgadata, size_t size) dataptr += 4; printf(" bytes in bitstream = %d\n", swapsize); - return fpga_load(devnum, dataptr, swapsize); + return fpga_load(devnum, dataptr, swapsize, bstype); } -int xilinx_load(xilinx_desc *desc, const void *buf, size_t bsize) +int xilinx_load(xilinx_desc *desc, const void *buf, size_t bsize, + bitstream_type bstype) { if (!xilinx_validate (desc, (char *)__FUNCTION__)) { printf ("%s: Invalid device descriptor\n", __FUNCTION__); return FPGA_FAIL; } - return desc->operations->load(desc, buf, bsize); + return desc->operations->load(desc, buf, bsize, bstype); } +#if defined(CONFIG_CMD_FPGA_LOADFS) +int xilinx_loadfs(xilinx_desc *desc, const void *buf, size_t bsize, + fpga_fs_info *fpga_fsinfo) +{ + if (!xilinx_validate(desc, (char *)__func__)) { + printf("%s: Invalid device descriptor\n", __func__); + return FPGA_FAIL; + } + + if (!desc->operations->loadfs) + return FPGA_FAIL; + + return desc->operations->loadfs(desc, buf, bsize, fpga_fsinfo); +} +#endif + int xilinx_dump(xilinx_desc *desc, const void *buf, size_t bsize) { if (!xilinx_validate (desc, (char *)__FUNCTION__)) { diff --git a/drivers/fpga/zynqpl.c b/drivers/fpga/zynqpl.c index c066f21d79..68fe0f3b03 100644 --- a/drivers/fpga/zynqpl.c +++ b/drivers/fpga/zynqpl.c @@ -9,6 +9,7 @@ #include <common.h> #include <asm/io.h> +#include <fs.h> #include <zynqpl.h> #include <linux/sizes.h> #include <asm/arch/hardware.h> @@ -194,7 +195,7 @@ static int zynq_dma_transfer(u32 srcbuf, u32 srclen, u32 dstbuf, u32 dstlen) return FPGA_SUCCESS; } -static int zynq_dma_xfer_init(u32 partialbit) +static int zynq_dma_xfer_init(bitstream_type bstype) { u32 status, control, isr_status; unsigned long ts; @@ -202,7 +203,7 @@ static int zynq_dma_xfer_init(u32 partialbit) /* Clear loopback bit */ clrbits_le32(&devcfg_base->mctrl, DEVCFG_MCTRL_PCAP_LPBK); - if (!partialbit) { + if (bstype != BIT_PARTIAL) { zynq_slcr_devcfg_disable(); /* Setting PCFG_PROG_B signal to high */ @@ -322,16 +323,11 @@ static u32 *zynq_align_dma_buffer(u32 *buf, u32 len, u32 swap) static int zynq_validate_bitstream(xilinx_desc *desc, const void *buf, size_t bsize, u32 blocksize, u32 *swap, - u32 *partialbit) + bitstream_type *bstype) { u32 *buf_start; u32 diff; - /* Detect if we are going working with partial or full bitstream */ - if (bsize != desc->size) { - printf("%s: Working with partial bitstream\n", __func__); - *partialbit = 1; - } buf_start = check_data((u8 *)buf, blocksize, swap); if (!buf_start) @@ -351,17 +347,16 @@ static int zynq_validate_bitstream(xilinx_desc *desc, const void *buf, return FPGA_FAIL; } - if (zynq_dma_xfer_init(*partialbit)) + if (zynq_dma_xfer_init(*bstype)) return FPGA_FAIL; return 0; } - -static int zynq_load(xilinx_desc *desc, const void *buf, size_t bsize) +static int zynq_load(xilinx_desc *desc, const void *buf, size_t bsize, + bitstream_type bstype) { unsigned long ts; /* Timestamp */ - u32 partialbit = 0; u32 isr_status, swap; /* @@ -369,7 +364,7 @@ static int zynq_load(xilinx_desc *desc, const void *buf, size_t bsize) * in chunks */ if (zynq_validate_bitstream(desc, buf, bsize, bsize, &swap, - &partialbit)) + &bstype)) return FPGA_FAIL; buf = zynq_align_dma_buffer((u32 *)buf, bsize, swap); @@ -398,11 +393,92 @@ static int zynq_load(xilinx_desc *desc, const void *buf, size_t bsize) debug("%s: FPGA config done\n", __func__); + if (bstype != BIT_PARTIAL) + zynq_slcr_devcfg_enable(); + + return FPGA_SUCCESS; +} + +#if defined(CONFIG_CMD_FPGA_LOADFS) +static int zynq_loadfs(xilinx_desc *desc, const void *buf, size_t bsize, + fpga_fs_info *fsinfo) +{ + unsigned long ts; /* Timestamp */ + u32 isr_status, swap; + u32 partialbit = 0; + u32 blocksize; + u32 pos = 0; + int fstype; + char *interface, *dev_part, *filename; + + blocksize = fsinfo->blocksize; + interface = fsinfo->interface; + dev_part = fsinfo->dev_part; + filename = fsinfo->filename; + fstype = fsinfo->fstype; + + if (fs_set_blk_dev(interface, dev_part, fstype)) + return FPGA_FAIL; + + if (fs_read(filename, (u32) buf, pos, blocksize) < 0) + return FPGA_FAIL; + + if (zynq_validate_bitstream(desc, buf, bsize, blocksize, &swap, + &partialbit)) + return FPGA_FAIL; + + dcache_disable(); + + do { + buf = zynq_align_dma_buffer((u32 *)buf, blocksize, swap); + + if (zynq_dma_transfer((u32)buf | 1, blocksize >> 2, + 0xffffffff, 0)) + return FPGA_FAIL; + + bsize -= blocksize; + pos += blocksize; + + if (fs_set_blk_dev(interface, dev_part, fstype)) + return FPGA_FAIL; + + if (bsize > blocksize) { + if (fs_read(filename, (u32) buf, pos, blocksize) < 0) + return FPGA_FAIL; + } else { + if (fs_read(filename, (u32) buf, pos, bsize) < 0) + return FPGA_FAIL; + } + } while (bsize > blocksize); + + buf = zynq_align_dma_buffer((u32 *)buf, blocksize, swap); + + if (zynq_dma_transfer((u32)buf | 1, bsize >> 2, 0xffffffff, 0)) + return FPGA_FAIL; + + dcache_enable(); + + isr_status = readl(&devcfg_base->int_sts); + + /* Check FPGA configuration completion */ + ts = get_timer(0); + while (!(isr_status & DEVCFG_ISR_PCFG_DONE)) { + if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) { + printf("%s: Timeout wait for FPGA to config\n", + __func__); + return FPGA_FAIL; + } + isr_status = readl(&devcfg_base->int_sts); + } + + debug("%s: FPGA config done\n", __func__); + if (!partialbit) zynq_slcr_devcfg_enable(); return FPGA_SUCCESS; } +#endif static int zynq_dump(xilinx_desc *desc, const void *buf, size_t bsize) { @@ -411,6 +487,9 @@ static int zynq_dump(xilinx_desc *desc, const void *buf, size_t bsize) struct xilinx_fpga_op zynq_op = { .load = zynq_load, +#if defined(CONFIG_CMD_FPGA_LOADFS) + .loadfs = zynq_loadfs, +#endif .dump = zynq_dump, .info = zynq_info, }; diff --git a/drivers/gpio/s5p_gpio.c b/drivers/gpio/s5p_gpio.c index 11a0472c69..db7b673731 100644 --- a/drivers/gpio/s5p_gpio.c +++ b/drivers/gpio/s5p_gpio.c @@ -8,11 +8,9 @@ #include <common.h> #include <asm/io.h> #include <asm/gpio.h> +#include <asm/arch/gpio.h> -#define S5P_GPIO_GET_BANK(x) ((x >> S5P_GPIO_BANK_SHIFT) \ - & S5P_GPIO_BANK_MASK) - -#define S5P_GPIO_GET_PIN(x) (x & S5P_GPIO_PIN_MASK) +#define S5P_GPIO_GET_PIN(x) (x % GPIO_PER_BANK) #define CON_MASK(x) (0xf << ((x) << 2)) #define CON_SFR(x, v) ((v) << ((x) << 2)) @@ -28,7 +26,103 @@ #define RATE_MASK(x) (0x1 << (x + 16)) #define RATE_SET(x) (0x1 << (x + 16)) -void s5p_gpio_cfg_pin(struct s5p_gpio_bank *bank, int gpio, int cfg) +#define name_to_gpio(n) s5p_name_to_gpio(n) +static inline int s5p_name_to_gpio(const char *name) +{ + unsigned num, irregular_set_number, irregular_bank_base; + const struct gpio_name_num_table *tabp; + char this_bank, bank_name, irregular_bank_name; + char *endp; + + /* + * The gpio name starts with either 'g' or 'gp' followed by the bank + * name character. Skip one or two characters depending on the prefix. + */ + if (name[0] == 'g' && name[1] == 'p') + name += 2; + else if (name[0] == 'g') + name++; + else + return -1; /* Name must start with 'g' */ + + bank_name = *name++; + if (!*name) + return -1; /* At least one digit is required/expected. */ + + /* + * On both exynos5 and exynos5420 architectures there is a bank of + * GPIOs which does not fall into the regular address pattern. Those + * banks are c4 on Exynos5 and y7 on Exynos5420. The rest of the below + * assignments help to handle these irregularities. + */ +#if defined(CONFIG_EXYNOS4) || defined(CONFIG_EXYNOS5) + if (cpu_is_exynos5()) { + if (proid_is_exynos5420()) { + tabp = exynos5420_gpio_table; + irregular_bank_name = 'y'; + irregular_set_number = '7'; + irregular_bank_base = EXYNOS5420_GPIO_Y70; + } else { + tabp = exynos5_gpio_table; + irregular_bank_name = 'c'; + irregular_set_number = '4'; + irregular_bank_base = EXYNOS5_GPIO_C40; + } + } else { + if (proid_is_exynos4412()) + tabp = exynos4x12_gpio_table; + else + tabp = exynos4_gpio_table; + irregular_bank_name = 0; + irregular_set_number = 0; + irregular_bank_base = 0; + } +#else + if (cpu_is_s5pc110()) + tabp = s5pc110_gpio_table; + else + tabp = s5pc100_gpio_table; + irregular_bank_name = 0; + irregular_set_number = 0; + irregular_bank_base = 0; +#endif + + this_bank = tabp->bank; + do { + if (bank_name == this_bank) { + unsigned pin_index; /* pin number within the bank */ + if ((bank_name == irregular_bank_name) && + (name[0] == irregular_set_number)) { + pin_index = name[1] - '0'; + /* Irregular sets have 8 pins. */ + if (pin_index >= GPIO_PER_BANK) + return -1; + num = irregular_bank_base + pin_index; + } else { + pin_index = simple_strtoul(name, &endp, 8); + pin_index -= tabp->bank_offset; + /* + * Sanity check: bunk 'z' has no set number, + * for all other banks there must be exactly + * two octal digits, and the resulting number + * should not exceed the number of pins in the + * bank. + */ + if (((bank_name != 'z') && !name[1]) || + *endp || + (pin_index >= tabp->bank_size)) + return -1; + num = tabp->base + pin_index; + } + return num; + } + this_bank = (++tabp)->bank; + } while (this_bank); + + return -1; +} + +static void s5p_gpio_cfg_pin(struct s5p_gpio_bank *bank, int gpio, int cfg) { unsigned int value; @@ -38,18 +132,7 @@ void s5p_gpio_cfg_pin(struct s5p_gpio_bank *bank, int gpio, int cfg) writel(value, &bank->con); } -void s5p_gpio_direction_output(struct s5p_gpio_bank *bank, int gpio, int en) -{ - s5p_gpio_cfg_pin(bank, gpio, GPIO_OUTPUT); - s5p_gpio_set_value(bank, gpio, en); -} - -void s5p_gpio_direction_input(struct s5p_gpio_bank *bank, int gpio) -{ - s5p_gpio_cfg_pin(bank, gpio, GPIO_INPUT); -} - -void s5p_gpio_set_value(struct s5p_gpio_bank *bank, int gpio, int en) +static void s5p_gpio_set_value(struct s5p_gpio_bank *bank, int gpio, int en) { unsigned int value; @@ -60,7 +143,19 @@ void s5p_gpio_set_value(struct s5p_gpio_bank *bank, int gpio, int en) writel(value, &bank->dat); } -unsigned int s5p_gpio_get_value(struct s5p_gpio_bank *bank, int gpio) +static void s5p_gpio_direction_output(struct s5p_gpio_bank *bank, + int gpio, int en) +{ + s5p_gpio_cfg_pin(bank, gpio, S5P_GPIO_OUTPUT); + s5p_gpio_set_value(bank, gpio, en); +} + +static void s5p_gpio_direction_input(struct s5p_gpio_bank *bank, int gpio) +{ + s5p_gpio_cfg_pin(bank, gpio, S5P_GPIO_INPUT); +} + +static unsigned int s5p_gpio_get_value(struct s5p_gpio_bank *bank, int gpio) { unsigned int value; @@ -68,7 +163,7 @@ unsigned int s5p_gpio_get_value(struct s5p_gpio_bank *bank, int gpio) return !!(value & DAT_MASK(gpio)); } -void s5p_gpio_set_pull(struct s5p_gpio_bank *bank, int gpio, int mode) +static void s5p_gpio_set_pull(struct s5p_gpio_bank *bank, int gpio, int mode) { unsigned int value; @@ -76,8 +171,8 @@ void s5p_gpio_set_pull(struct s5p_gpio_bank *bank, int gpio, int mode) value &= ~PULL_MASK(gpio); switch (mode) { - case GPIO_PULL_DOWN: - case GPIO_PULL_UP: + case S5P_GPIO_PULL_DOWN: + case S5P_GPIO_PULL_UP: value |= PULL_MODE(gpio, mode); break; default: @@ -87,7 +182,7 @@ void s5p_gpio_set_pull(struct s5p_gpio_bank *bank, int gpio, int mode) writel(value, &bank->pull); } -void s5p_gpio_set_drv(struct s5p_gpio_bank *bank, int gpio, int mode) +static void s5p_gpio_set_drv(struct s5p_gpio_bank *bank, int gpio, int mode) { unsigned int value; @@ -95,10 +190,10 @@ void s5p_gpio_set_drv(struct s5p_gpio_bank *bank, int gpio, int mode) value &= ~DRV_MASK(gpio); switch (mode) { - case GPIO_DRV_1X: - case GPIO_DRV_2X: - case GPIO_DRV_3X: - case GPIO_DRV_4X: + case S5P_GPIO_DRV_1X: + case S5P_GPIO_DRV_2X: + case S5P_GPIO_DRV_3X: + case S5P_GPIO_DRV_4X: value |= DRV_SET(gpio, mode); break; default: @@ -108,7 +203,7 @@ void s5p_gpio_set_drv(struct s5p_gpio_bank *bank, int gpio, int mode) writel(value, &bank->drv); } -void s5p_gpio_set_rate(struct s5p_gpio_bank *bank, int gpio, int mode) +static void s5p_gpio_set_rate(struct s5p_gpio_bank *bank, int gpio, int mode) { unsigned int value; @@ -116,8 +211,8 @@ void s5p_gpio_set_rate(struct s5p_gpio_bank *bank, int gpio, int mode) value &= ~RATE_MASK(gpio); switch (mode) { - case GPIO_DRV_FAST: - case GPIO_DRV_SLOW: + case S5P_GPIO_DRV_FAST: + case S5P_GPIO_DRV_SLOW: value |= RATE_SET(gpio); break; default: @@ -127,12 +222,31 @@ void s5p_gpio_set_rate(struct s5p_gpio_bank *bank, int gpio, int mode) writel(value, &bank->drv); } -struct s5p_gpio_bank *s5p_gpio_get_bank(unsigned gpio) +struct s5p_gpio_bank *s5p_gpio_get_bank(unsigned int gpio) { - unsigned bank = S5P_GPIO_GET_BANK(gpio); - unsigned base = s5p_gpio_base(gpio); + const struct gpio_info *data; + unsigned int upto; + int i, count; + + data = get_gpio_data(); + count = get_bank_num(); + upto = 0; + + for (i = 0; i < count; i++) { + debug("i=%d, upto=%d\n", i, upto); + if (gpio < data->max_gpio) { + struct s5p_gpio_bank *bank; + bank = (struct s5p_gpio_bank *)data->reg_addr; + bank += (gpio - upto) / GPIO_PER_BANK; + debug("gpio=%d, bank=%p\n", gpio, bank); + return bank; + } + + upto = data->max_gpio; + data++; + } - return (struct s5p_gpio_bank *)(base + bank); + return NULL; } int s5p_gpio_get_pin(unsigned gpio) @@ -179,3 +293,27 @@ int gpio_set_value(unsigned gpio, int value) return 0; } + +void gpio_set_pull(int gpio, int mode) +{ + s5p_gpio_set_pull(s5p_gpio_get_bank(gpio), + s5p_gpio_get_pin(gpio), mode); +} + +void gpio_set_drv(int gpio, int mode) +{ + s5p_gpio_set_drv(s5p_gpio_get_bank(gpio), + s5p_gpio_get_pin(gpio), mode); +} + +void gpio_cfg_pin(int gpio, int cfg) +{ + s5p_gpio_cfg_pin(s5p_gpio_get_bank(gpio), + s5p_gpio_get_pin(gpio), cfg); +} + +void gpio_set_rate(int gpio, int mode) +{ + s5p_gpio_set_rate(s5p_gpio_get_bank(gpio), + s5p_gpio_get_pin(gpio), mode); +} diff --git a/drivers/gpio/tegra_gpio.c b/drivers/gpio/tegra_gpio.c index 82b30d5ab6..fea9d17f8e 100644 --- a/drivers/gpio/tegra_gpio.c +++ b/drivers/gpio/tegra_gpio.c @@ -221,6 +221,26 @@ int gpio_set_value(unsigned gpio, int value) return 0; } +void gpio_config_table(const struct tegra_gpio_config *config, int len) +{ + int i; + + for (i = 0; i < len; i++) { + switch (config[i].init) { + case TEGRA_GPIO_INIT_IN: + gpio_direction_input(config[i].gpio); + break; + case TEGRA_GPIO_INIT_OUT0: + gpio_direction_output(config[i].gpio, 0); + break; + case TEGRA_GPIO_INIT_OUT1: + gpio_direction_output(config[i].gpio, 1); + break; + } + set_config(config[i].gpio, 1); + } +} + /* * Display Tegra GPIO information */ diff --git a/drivers/i2c/mvtwsi.c b/drivers/i2c/mvtwsi.c index 90c8387918..5ba0e03862 100644 --- a/drivers/i2c/mvtwsi.c +++ b/drivers/i2c/mvtwsi.c @@ -216,21 +216,7 @@ static int twsi_stop(int status) */ #define TWSI_FREQUENCY(m, n) \ - ((u8) (CONFIG_SYS_TCLK / (10 * (m + 1) * 2 * (1 << n)))) - -/* - * These are required to be reprogrammed before enabling the controller - * because a reset loses them. - * Default values come from the spec, but a twsi_reset will change them. - * twsi_slave_address left uninitialized lest checkpatch.pl complains. - */ - -/* Baudrate generator: m (bits 7..4) =4, n (bits 3..0) =4 */ -static u8 twsi_baud_rate = 0x44; /* baudrate at controller reset */ -/* Default frequency corresponding to default m=4, n=4 */ -static u8 twsi_actual_speed = TWSI_FREQUENCY(4, 4); -/* Default slave address is 0 (so is an uninitialized static) */ -static u8 twsi_slave_address; + (CONFIG_SYS_TCLK / (10 * (m + 1) * (1 << n))) /* * Reset controller. @@ -238,7 +224,7 @@ static u8 twsi_slave_address; * Controller reset also resets the baud rate and slave address, so * re-establish them. */ -static void twsi_reset(void) +static void twsi_reset(u8 baud_rate, u8 slave_address) { /* ensure controller will be enabled by any twsi*() function */ twsi_control_flags = MVTWSI_CONTROL_TWSIEN; @@ -247,9 +233,9 @@ static void twsi_reset(void) /* wait 2 ms -- this is what the Marvell LSP does */ udelay(20000); /* set baud rate */ - writel(twsi_baud_rate, &twsi->baudrate); + writel(baud_rate, &twsi->baudrate); /* set slave address even though we don't use it */ - writel(twsi_slave_address, &twsi->slave_address); + writel(slave_address, &twsi->slave_address); writel(0, &twsi->xtnd_slave_addr); /* assert STOP but don't care for the result */ (void) twsi_stop(0); @@ -277,12 +263,8 @@ void i2c_init(int requested_speed, int slaveadd) } } } - /* save baud rate and slave for later calls to twsi_reset */ - twsi_baud_rate = baud; - twsi_actual_speed = highest_speed; - twsi_slave_address = slaveadd; /* reset controller */ - twsi_reset(); + twsi_reset(baud, slaveadd); } /* diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile index 931922bc4a..4c6ab9e05b 100644 --- a/drivers/mmc/Makefile +++ b/drivers/mmc/Makefile @@ -30,6 +30,7 @@ obj-$(CONFIG_DWMMC) += dw_mmc.o obj-$(CONFIG_EXYNOS_DWMMC) += exynos_dw_mmc.o obj-$(CONFIG_ZYNQ_SDHCI) += zynq_sdhci.o obj-$(CONFIG_SOCFPGA_DWMMC) += socfpga_dw_mmc.o +obj-$(CONFIG_SUPPORT_EMMC_RPMB) += rpmb.o ifdef CONFIG_SPL_BUILD obj-$(CONFIG_SPL_MMC_BOOT) += fsl_esdhc_spl.o else diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c index 4c3b93d413..55416136ab 100644 --- a/drivers/mmc/fsl_esdhc.c +++ b/drivers/mmc/fsl_esdhc.c @@ -96,7 +96,7 @@ static uint esdhc_xfertyp(struct mmc_cmd *cmd, struct mmc_data *data) else if (cmd->resp_type & MMC_RSP_PRESENT) xfertyp |= XFERTYP_RSPTYP_48; -#if defined(CONFIG_MX53) || defined(CONFIG_T4240QDS) +#if defined(CONFIG_MX53) || defined(CONFIG_PPC_T4240) if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION) xfertyp |= XFERTYP_CMDTYP_ABORT; #endif @@ -174,7 +174,7 @@ static int esdhc_setup_data(struct mmc *mmc, struct mmc_data *data) int timeout; struct fsl_esdhc_cfg *cfg = mmc->priv; struct fsl_esdhc *regs = (struct fsl_esdhc *)cfg->esdhc_base; -#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO + uint wml_value; wml_value = data->blocksize/4; @@ -184,12 +184,15 @@ static int esdhc_setup_data(struct mmc *mmc, struct mmc_data *data) wml_value = WML_RD_WML_MAX_VAL; esdhc_clrsetbits32(®s->wml, WML_RD_WML_MASK, wml_value); +#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO esdhc_write32(®s->dsaddr, (u32)data->dest); +#endif } else { +#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO flush_dcache_range((ulong)data->src, (ulong)data->src+data->blocks *data->blocksize); - +#endif if (wml_value > WML_WR_WML_MAX) wml_value = WML_WR_WML_MAX_VAL; if ((esdhc_read32(®s->prsstat) & PRSSTAT_WPSPL) == 0) { @@ -199,19 +202,10 @@ static int esdhc_setup_data(struct mmc *mmc, struct mmc_data *data) esdhc_clrsetbits32(®s->wml, WML_WR_WML_MASK, wml_value << 16); +#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO esdhc_write32(®s->dsaddr, (u32)data->src); +#endif } -#else /* CONFIG_SYS_FSL_ESDHC_USE_PIO */ - if (!(data->flags & MMC_DATA_READ)) { - if ((esdhc_read32(®s->prsstat) & PRSSTAT_WPSPL) == 0) { - printf("\nThe SD card is locked. " - "Can not write to a locked card.\n\n"); - return TIMEOUT; - } - esdhc_write32(®s->dsaddr, (u32)data->src); - } else - esdhc_write32(®s->dsaddr, (u32)data->dest); -#endif /* CONFIG_SYS_FSL_ESDHC_USE_PIO */ esdhc_write32(®s->blkattr, data->blocks << 16 | data->blocksize); @@ -252,6 +246,7 @@ static int esdhc_setup_data(struct mmc *mmc, struct mmc_data *data) return 0; } +#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO static void check_and_invalidate_dcache_range (struct mmc_cmd *cmd, struct mmc_data *data) { @@ -261,6 +256,8 @@ static void check_and_invalidate_dcache_range unsigned end = start+size ; invalidate_dcache_range(start, end); } +#endif + /* * Sends a command out on the bus. Takes the mmc pointer, * a command pointer, and an optional data pointer. @@ -388,9 +385,10 @@ esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data) goto out; } } while ((irqstat & DATA_COMPLETE) != DATA_COMPLETE); -#endif + if (data->flags & MMC_DATA_READ) check_and_invalidate_dcache_range(cmd, data); +#endif } out: diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c index 16051e52ff..8b53ead98f 100644 --- a/drivers/mmc/mmc.c +++ b/drivers/mmc/mmc.c @@ -150,6 +150,8 @@ int mmc_send_status(struct mmc *mmc, int timeout) #endif return TIMEOUT; } + if (cmd.response[0] & MMC_STATUS_SWITCH_ERROR) + return SWITCH_ERR; return 0; } @@ -501,7 +503,7 @@ static int mmc_change_freq(struct mmc *mmc) err = mmc_switch(mmc, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_HS_TIMING, 1); if (err) - return err; + return err == SWITCH_ERR ? 0 : err; /* Now check to see that it worked */ err = mmc_send_ext_csd(mmc, ext_csd); @@ -550,6 +552,32 @@ static int mmc_set_capacity(struct mmc *mmc, int part_num) return 0; } +int mmc_select_hwpart(int dev_num, int hwpart) +{ + struct mmc *mmc = find_mmc_device(dev_num); + int ret; + + if (!mmc) + return -1; + + if (mmc->part_num == hwpart) + return 0; + + if (mmc->part_config == MMCPART_NOAVAILABLE) { + printf("Card doesn't support part_switch\n"); + return -1; + } + + ret = mmc_switch_part(dev_num, hwpart); + if (ret) + return -1; + + mmc->part_num = hwpart; + + return 0; +} + + int mmc_switch_part(int dev_num, unsigned int part_num) { struct mmc *mmc = find_mmc_device(dev_num); @@ -1310,10 +1338,13 @@ static int mmc_complete_init(struct mmc *mmc) int mmc_init(struct mmc *mmc) { int err = IN_PROGRESS; - unsigned start = get_timer(0); + unsigned start; if (mmc->has_init) return 0; + + start = get_timer(0); + if (!mmc->init_in_progress) err = mmc_start_init(mmc); diff --git a/drivers/mmc/rpmb.c b/drivers/mmc/rpmb.c new file mode 100644 index 0000000000..05936f5d1f --- /dev/null +++ b/drivers/mmc/rpmb.c @@ -0,0 +1,323 @@ +/* + * Copyright 2014, Staubli Faverges + * Pierre Aubert + * + * eMMC- Replay Protected Memory Block + * According to JEDEC Standard No. 84-A441 + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <config.h> +#include <common.h> +#include <mmc.h> +#include <sha256.h> +#include "mmc_private.h" + +/* Request codes */ +#define RPMB_REQ_KEY 1 +#define RPMB_REQ_WCOUNTER 2 +#define RPMB_REQ_WRITE_DATA 3 +#define RPMB_REQ_READ_DATA 4 +#define RPMB_REQ_STATUS 5 + +/* Response code */ +#define RPMB_RESP_KEY 0x0100 +#define RPMB_RESP_WCOUNTER 0x0200 +#define RPMB_RESP_WRITE_DATA 0x0300 +#define RPMB_RESP_READ_DATA 0x0400 + +/* Error codes */ +#define RPMB_OK 0 +#define RPMB_ERR_GENERAL 1 +#define RPMB_ERR_AUTH 2 +#define RPMB_ERR_COUNTER 3 +#define RPMB_ERR_ADDRESS 4 +#define RPMB_ERR_WRITE 5 +#define RPMB_ERR_READ 6 +#define RPMB_ERR_KEY 7 +#define RPMB_ERR_CNT_EXPIRED 0x80 +#define RPMB_ERR_MSK 0x7 + +/* Sizes of RPMB data frame */ +#define RPMB_SZ_STUFF 196 +#define RPMB_SZ_MAC 32 +#define RPMB_SZ_DATA 256 +#define RPMB_SZ_NONCE 16 + +#define SHA256_BLOCK_SIZE 64 + +/* Error messages */ +static const char * const rpmb_err_msg[] = { + "", + "General failure", + "Authentication failure", + "Counter failure", + "Address failure", + "Write failure", + "Read failure", + "Authentication key not yet programmed", +}; + + +/* Structure of RPMB data frame. */ +struct s_rpmb { + unsigned char stuff[RPMB_SZ_STUFF]; + unsigned char mac[RPMB_SZ_MAC]; + unsigned char data[RPMB_SZ_DATA]; + unsigned char nonce[RPMB_SZ_NONCE]; + unsigned long write_counter; + unsigned short address; + unsigned short block_count; + unsigned short result; + unsigned short request; +}; + +static int mmc_set_blockcount(struct mmc *mmc, unsigned int blockcount, + bool is_rel_write) +{ + struct mmc_cmd cmd = {0}; + + cmd.cmdidx = MMC_CMD_SET_BLOCK_COUNT; + cmd.cmdarg = blockcount & 0x0000FFFF; + if (is_rel_write) + cmd.cmdarg |= 1 << 31; + cmd.resp_type = MMC_RSP_R1; + + return mmc_send_cmd(mmc, &cmd, NULL); +} +static int mmc_rpmb_request(struct mmc *mmc, const struct s_rpmb *s, + unsigned int count, bool is_rel_write) +{ + struct mmc_cmd cmd = {0}; + struct mmc_data data; + int ret; + + ret = mmc_set_blockcount(mmc, count, is_rel_write); + if (ret) { +#ifdef CONFIG_MMC_RPMB_TRACE + printf("%s:mmc_set_blockcount-> %d\n", __func__, ret); +#endif + return 1; + } + + cmd.cmdidx = MMC_CMD_WRITE_MULTIPLE_BLOCK; + cmd.cmdarg = 0; + cmd.resp_type = MMC_RSP_R1b; + + data.src = (const char *)s; + data.blocks = 1; + data.blocksize = MMC_MAX_BLOCK_LEN; + data.flags = MMC_DATA_WRITE; + + ret = mmc_send_cmd(mmc, &cmd, &data); + if (ret) { +#ifdef CONFIG_MMC_RPMB_TRACE + printf("%s:mmc_send_cmd-> %d\n", __func__, ret); +#endif + return 1; + } + return 0; +} +static int mmc_rpmb_response(struct mmc *mmc, struct s_rpmb *s, + unsigned short expected) +{ + struct mmc_cmd cmd = {0}; + struct mmc_data data; + int ret; + + ret = mmc_set_blockcount(mmc, 1, false); + if (ret) { +#ifdef CONFIG_MMC_RPMB_TRACE + printf("%s:mmc_set_blockcount-> %d\n", __func__, ret); +#endif + return -1; + } + cmd.cmdidx = MMC_CMD_READ_MULTIPLE_BLOCK; + cmd.cmdarg = 0; + cmd.resp_type = MMC_RSP_R1; + + data.dest = (char *)s; + data.blocks = 1; + data.blocksize = MMC_MAX_BLOCK_LEN; + data.flags = MMC_DATA_READ; + + ret = mmc_send_cmd(mmc, &cmd, &data); + if (ret) { +#ifdef CONFIG_MMC_RPMB_TRACE + printf("%s:mmc_send_cmd-> %d\n", __func__, ret); +#endif + return -1; + } + /* Check the response and the status */ + if (be16_to_cpu(s->request) != expected) { +#ifdef CONFIG_MMC_RPMB_TRACE + printf("%s:response= %x\n", __func__, + be16_to_cpu(s->request)); +#endif + return -1; + } + ret = be16_to_cpu(s->result); + if (ret) { + printf("%s %s\n", rpmb_err_msg[ret & RPMB_ERR_MSK], + (ret & RPMB_ERR_CNT_EXPIRED) ? + "Write counter has expired" : ""); + } + + /* Return the status of the command */ + return ret; +} +static int mmc_rpmb_status(struct mmc *mmc, unsigned short expected) +{ + ALLOC_CACHE_ALIGN_BUFFER(struct s_rpmb, rpmb_frame, 1); + + memset(rpmb_frame, 0, sizeof(struct s_rpmb)); + rpmb_frame->request = cpu_to_be16(RPMB_REQ_STATUS); + if (mmc_rpmb_request(mmc, rpmb_frame, 1, false)) + return -1; + + /* Read the result */ + return mmc_rpmb_response(mmc, rpmb_frame, expected); +} +static void rpmb_hmac(unsigned char *key, unsigned char *buff, int len, + unsigned char *output) +{ + sha256_context ctx; + int i; + unsigned char k_ipad[SHA256_BLOCK_SIZE]; + unsigned char k_opad[SHA256_BLOCK_SIZE]; + + sha256_starts(&ctx); + + /* According to RFC 4634, the HMAC transform looks like: + SHA(K XOR opad, SHA(K XOR ipad, text)) + + where K is an n byte key. + ipad is the byte 0x36 repeated blocksize times + opad is the byte 0x5c repeated blocksize times + and text is the data being protected. + */ + + for (i = 0; i < RPMB_SZ_MAC; i++) { + k_ipad[i] = key[i] ^ 0x36; + k_opad[i] = key[i] ^ 0x5c; + } + /* remaining pad bytes are '\0' XOR'd with ipad and opad values */ + for ( ; i < SHA256_BLOCK_SIZE; i++) { + k_ipad[i] = 0x36; + k_opad[i] = 0x5c; + } + sha256_update(&ctx, k_ipad, SHA256_BLOCK_SIZE); + sha256_update(&ctx, buff, len); + sha256_finish(&ctx, output); + + /* Init context for second pass */ + sha256_starts(&ctx); + + /* start with outer pad */ + sha256_update(&ctx, k_opad, SHA256_BLOCK_SIZE); + + /* then results of 1st hash */ + sha256_update(&ctx, output, RPMB_SZ_MAC); + + /* finish up 2nd pass */ + sha256_finish(&ctx, output); +} +int mmc_rpmb_get_counter(struct mmc *mmc, unsigned long *pcounter) +{ + int ret; + ALLOC_CACHE_ALIGN_BUFFER(struct s_rpmb, rpmb_frame, 1); + + /* Fill the request */ + memset(rpmb_frame, 0, sizeof(struct s_rpmb)); + rpmb_frame->request = cpu_to_be16(RPMB_REQ_WCOUNTER); + if (mmc_rpmb_request(mmc, rpmb_frame, 1, false)) + return -1; + + /* Read the result */ + ret = mmc_rpmb_response(mmc, rpmb_frame, RPMB_RESP_WCOUNTER); + if (ret) + return ret; + + *pcounter = be32_to_cpu(rpmb_frame->write_counter); + return 0; +} +int mmc_rpmb_set_key(struct mmc *mmc, void *key) +{ + ALLOC_CACHE_ALIGN_BUFFER(struct s_rpmb, rpmb_frame, 1); + /* Fill the request */ + memset(rpmb_frame, 0, sizeof(struct s_rpmb)); + rpmb_frame->request = cpu_to_be16(RPMB_REQ_KEY); + memcpy(rpmb_frame->mac, key, RPMB_SZ_MAC); + + if (mmc_rpmb_request(mmc, rpmb_frame, 1, true)) + return -1; + + /* read the operation status */ + return mmc_rpmb_status(mmc, RPMB_RESP_KEY); +} +int mmc_rpmb_read(struct mmc *mmc, void *addr, unsigned short blk, + unsigned short cnt, unsigned char *key) +{ + ALLOC_CACHE_ALIGN_BUFFER(struct s_rpmb, rpmb_frame, 1); + int i; + + for (i = 0; i < cnt; i++) { + /* Fill the request */ + memset(rpmb_frame, 0, sizeof(struct s_rpmb)); + rpmb_frame->address = cpu_to_be16(blk + i); + rpmb_frame->request = cpu_to_be16(RPMB_REQ_READ_DATA); + if (mmc_rpmb_request(mmc, rpmb_frame, 1, false)) + break; + + /* Read the result */ + if (mmc_rpmb_response(mmc, rpmb_frame, RPMB_RESP_READ_DATA)) + break; + + /* Check the HMAC if key is provided */ + if (key) { + unsigned char ret_hmac[RPMB_SZ_MAC]; + + rpmb_hmac(key, rpmb_frame->data, 284, ret_hmac); + if (memcmp(ret_hmac, rpmb_frame->mac, RPMB_SZ_MAC)) { + printf("MAC error on block #%d\n", i); + break; + } + } + /* Copy data */ + memcpy(addr + i * RPMB_SZ_DATA, rpmb_frame->data, RPMB_SZ_DATA); + } + return i; +} +int mmc_rpmb_write(struct mmc *mmc, void *addr, unsigned short blk, + unsigned short cnt, unsigned char *key) +{ + ALLOC_CACHE_ALIGN_BUFFER(struct s_rpmb, rpmb_frame, 1); + unsigned long wcount; + int i; + + for (i = 0; i < cnt; i++) { + if (mmc_rpmb_get_counter(mmc, &wcount)) { + printf("Cannot read RPMB write counter\n"); + break; + } + + /* Fill the request */ + memset(rpmb_frame, 0, sizeof(struct s_rpmb)); + memcpy(rpmb_frame->data, addr + i * RPMB_SZ_DATA, RPMB_SZ_DATA); + rpmb_frame->address = cpu_to_be16(blk + i); + rpmb_frame->block_count = cpu_to_be16(1); + rpmb_frame->write_counter = cpu_to_be32(wcount); + rpmb_frame->request = cpu_to_be16(RPMB_REQ_WRITE_DATA); + /* Computes HMAC */ + rpmb_hmac(key, rpmb_frame->data, 284, rpmb_frame->mac); + + if (mmc_rpmb_request(mmc, rpmb_frame, 1, true)) + break; + + /* Get status */ + if (mmc_rpmb_status(mmc, RPMB_RESP_WRITE_DATA)) + break; + } + return i; +} diff --git a/drivers/mmc/tegra_mmc.c b/drivers/mmc/tegra_mmc.c index ed67eec252..ca9c4aa15f 100644 --- a/drivers/mmc/tegra_mmc.c +++ b/drivers/mmc/tegra_mmc.c @@ -18,7 +18,7 @@ DECLARE_GLOBAL_DATA_PTR; -struct mmc_host mmc_host[MAX_HOSTS]; +struct mmc_host mmc_host[CONFIG_SYS_MMC_MAX_DEVICE]; #ifndef CONFIG_OF_CONTROL #error "Please enable device tree support to use this driver" @@ -669,13 +669,14 @@ static int process_nodes(const void *blob, int node_list[], int count) void tegra_mmc_init(void) { - int node_list[MAX_HOSTS], count; + int node_list[CONFIG_SYS_MMC_MAX_DEVICE], count; const void *blob = gd->fdt_blob; debug("%s entry\n", __func__); /* See if any Tegra124 MMC controllers are present */ count = fdtdec_find_aliases_for_id(blob, "sdhci", - COMPAT_NVIDIA_TEGRA124_SDMMC, node_list, MAX_HOSTS); + COMPAT_NVIDIA_TEGRA124_SDMMC, node_list, + CONFIG_SYS_MMC_MAX_DEVICE); debug("%s: count of Tegra124 sdhci nodes is %d\n", __func__, count); if (process_nodes(blob, node_list, count)) { printf("%s: Error processing T30 mmc node(s)!\n", __func__); @@ -684,7 +685,8 @@ void tegra_mmc_init(void) /* See if any Tegra30 MMC controllers are present */ count = fdtdec_find_aliases_for_id(blob, "sdhci", - COMPAT_NVIDIA_TEGRA30_SDMMC, node_list, MAX_HOSTS); + COMPAT_NVIDIA_TEGRA30_SDMMC, node_list, + CONFIG_SYS_MMC_MAX_DEVICE); debug("%s: count of T30 sdhci nodes is %d\n", __func__, count); if (process_nodes(blob, node_list, count)) { printf("%s: Error processing T30 mmc node(s)!\n", __func__); @@ -693,7 +695,8 @@ void tegra_mmc_init(void) /* Now look for any Tegra20 MMC controllers */ count = fdtdec_find_aliases_for_id(blob, "sdhci", - COMPAT_NVIDIA_TEGRA20_SDMMC, node_list, MAX_HOSTS); + COMPAT_NVIDIA_TEGRA20_SDMMC, node_list, + CONFIG_SYS_MMC_MAX_DEVICE); debug("%s: count of T20 sdhci nodes is %d\n", __func__, count); if (process_nodes(blob, node_list, count)) { printf("%s: Error processing T20 mmc node(s)!\n", __func__); diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c index 881a63618c..bf99b8e675 100644 --- a/drivers/mtd/nand/omap_gpmc.c +++ b/drivers/mtd/nand/omap_gpmc.c @@ -403,7 +403,7 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat, dat[byte_pos] ^= 1 << bit_pos; printf("nand: bit-flip corrected @data=%d\n", byte_pos); } else if (byte_pos < error_max) { - read_ecc[byte_pos - SECTOR_BYTES] = 1 << bit_pos; + read_ecc[byte_pos - SECTOR_BYTES] ^= 1 << bit_pos; printf("nand: bit-flip corrected @oob=%d\n", byte_pos - SECTOR_BYTES); } else { diff --git a/drivers/net/fm/Makefile b/drivers/net/fm/Makefile index ee5d768937..5ae3b167a9 100644 --- a/drivers/net/fm/Makefile +++ b/drivers/net/fm/Makefile @@ -32,5 +32,6 @@ obj-$(CONFIG_PPC_T2080) += t2080.o obj-$(CONFIG_PPC_T2081) += t2080.o obj-$(CONFIG_PPC_T4240) += t4240.o obj-$(CONFIG_PPC_T4160) += t4240.o +obj-$(CONFIG_PPC_T4080) += t4240.o obj-$(CONFIG_PPC_B4420) += b4860.o obj-$(CONFIG_PPC_B4860) += b4860.o diff --git a/drivers/net/fm/memac_phy.c b/drivers/net/fm/memac_phy.c index 2f4bc11a6c..de9c0e9cd2 100644 --- a/drivers/net/fm/memac_phy.c +++ b/drivers/net/fm/memac_phy.c @@ -29,10 +29,8 @@ int memac_mdio_write(struct mii_dev *bus, int port_addr, int dev_addr, c45 = 0; /* clause 22 */ dev_addr = regnum & 0x1f; clrbits_be32(®s->mdio_stat, MDIO_STAT_ENC); - } else { + } else setbits_be32(®s->mdio_stat, MDIO_STAT_ENC); - setbits_be32(®s->mdio_stat, MDIO_STAT_HOLD_15_CLK); - } /* Wait till the bus is free */ while ((in_be32(®s->mdio_stat)) & MDIO_STAT_BSY) @@ -76,10 +74,8 @@ int memac_mdio_read(struct mii_dev *bus, int port_addr, int dev_addr, c45 = 0; /* clause 22 */ dev_addr = regnum & 0x1f; clrbits_be32(®s->mdio_stat, MDIO_STAT_ENC); - } else { + } else setbits_be32(®s->mdio_stat, MDIO_STAT_ENC); - setbits_be32(®s->mdio_stat, MDIO_STAT_HOLD_15_CLK); - } /* Wait till the bus is free */ while ((in_be32(®s->mdio_stat)) & MDIO_STAT_BSY) diff --git a/drivers/net/phy/vitesse.c b/drivers/net/phy/vitesse.c index 3a55d271a5..c58fe50b72 100644 --- a/drivers/net/phy/vitesse.c +++ b/drivers/net/phy/vitesse.c @@ -58,6 +58,14 @@ #define MIIM_VSC8514_18G_QSGMII 0x80e0 #define MIIM_VSC8514_18G_CMDSTAT 0x8000 +/* Vitesse VSC8664 Control/Status Register */ +#define MIIM_VSC8664_SERDES_AND_SIGDET 0x13 +#define MIIM_VSC8664_ADDITIONAL_DEV 0x16 +#define MIIM_VSC8664_EPHY_CON 0x17 +#define MIIM_VSC8664_LED_CON 0x1E + +#define PHY_EXT_PAGE_ACCESS_EXTENDED 0x0001 + /* CIS8201 */ static int vitesse_config(struct phy_device *phydev) { @@ -244,6 +252,33 @@ static int vsc8514_config(struct phy_device *phydev) return 0; } +static int vsc8664_config(struct phy_device *phydev) +{ + u32 val; + + /* Enable MAC interface auto-negotiation */ + phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS, 0); + val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_EPHY_CON); + val |= (1 << 13); + phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_EPHY_CON, val); + + phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS, + PHY_EXT_PAGE_ACCESS_EXTENDED); + val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_SERDES_AND_SIGDET); + val |= (1 << 11); + phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_SERDES_AND_SIGDET, val); + phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS, 0); + + /* Enable LED blink */ + val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_LED_CON); + val &= ~(1 << 2); + phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_LED_CON, val); + + genphy_config_aneg(phydev); + + return 0; +} + static struct phy_driver VSC8211_driver = { .name = "Vitesse VSC8211", .uid = 0xfc4b0, @@ -334,6 +369,16 @@ static struct phy_driver VSC8662_driver = { .shutdown = &genphy_shutdown, }; +static struct phy_driver VSC8664_driver = { + .name = "Vitesse VSC8664", + .uid = 0x70660, + .mask = 0xffff0, + .features = PHY_GBIT_FEATURES, + .config = &vsc8664_config, + .startup = &vitesse_startup, + .shutdown = &genphy_shutdown, +}; + /* Vitesse bought Cicada, so we'll put these here */ static struct phy_driver cis8201_driver = { .name = "CIS8201", @@ -366,6 +411,7 @@ int phy_vitesse_init(void) phy_register(&VSC8574_driver); phy_register(&VSC8514_driver); phy_register(&VSC8662_driver); + phy_register(&VSC8664_driver); phy_register(&cis8201_driver); phy_register(&cis8204_driver); diff --git a/drivers/pci/fsl_pci_init.c b/drivers/pci/fsl_pci_init.c index 6317fb1324..3a41b0ec17 100644 --- a/drivers/pci/fsl_pci_init.c +++ b/drivers/pci/fsl_pci_init.c @@ -49,8 +49,13 @@ static void set_inbound_window(volatile pit_t *pi, u64 size) { u32 sz = (__ilog2_u64(size) - 1); - u32 flag = PIWAR_EN | PIWAR_LOCAL | - PIWAR_READ_SNOOP | PIWAR_WRITE_SNOOP; +#ifdef CONFIG_SYS_FSL_ERRATUM_A005434 + u32 flag = 0; +#else + u32 flag = PIWAR_LOCAL; +#endif + + flag |= PIWAR_EN | PIWAR_READ_SNOOP | PIWAR_WRITE_SNOOP; out_be32(&pi->pitar, r->phys_start >> 12); out_be32(&pi->piwbar, r->bus_start >> 12); diff --git a/drivers/power/pmic/Makefile b/drivers/power/pmic/Makefile index 4129bdabfb..920bbdce6e 100644 --- a/drivers/power/pmic/Makefile +++ b/drivers/power/pmic/Makefile @@ -5,6 +5,7 @@ # SPDX-License-Identifier: GPL-2.0+ # +obj-$(CONFIG_POWER_LTC3676) += pmic_ltc3676.o obj-$(CONFIG_POWER_MAX8998) += pmic_max8998.o obj-$(CONFIG_POWER_MAX8997) += pmic_max8997.o obj-$(CONFIG_POWER_MUIC_MAX8997) += muic_max8997.o diff --git a/drivers/power/pmic/pmic_ltc3676.c b/drivers/power/pmic/pmic_ltc3676.c new file mode 100644 index 0000000000..9b874cb07c --- /dev/null +++ b/drivers/power/pmic/pmic_ltc3676.c @@ -0,0 +1,32 @@ +/* + * Copyright (C) 2014 Gateworks Corporation + * Tim Harvey <tharvey@gateworks.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <errno.h> +#include <i2c.h> +#include <power/pmic.h> +#include <power/ltc3676_pmic.h> + +int power_ltc3676_init(unsigned char bus) +{ + static const char name[] = "LTC3676_PMIC"; + struct pmic *p = pmic_alloc(); + + if (!p) { + printf("%s: POWER allocation error!\n", __func__); + return -ENOMEM; + } + + p->name = name; + p->interface = PMIC_I2C; + p->number_of_regs = LTC3676_NUM_OF_REGS; + p->hw.i2c.addr = CONFIG_POWER_LTC3676_I2C_ADDR; + p->hw.i2c.tx_num = 1; + p->bus = bus; + + return 0; +} diff --git a/drivers/power/pmic/pmic_pfuze100.c b/drivers/power/pmic/pmic_pfuze100.c index 22c1f15eeb..21f12d2564 100644 --- a/drivers/power/pmic/pmic_pfuze100.c +++ b/drivers/power/pmic/pmic_pfuze100.c @@ -11,7 +11,7 @@ #include <power/pmic.h> #include <power/pfuze100_pmic.h> -int pmic_init(unsigned char bus) +int power_pfuze100_init(unsigned char bus) { static const char name[] = "PFUZE100_PMIC"; struct pmic *p = pmic_alloc(); diff --git a/drivers/qe/qe.c b/drivers/qe/qe.c index b1da75ec4d..9c5fbd1d69 100644 --- a/drivers/qe/qe.c +++ b/drivers/qe/qe.c @@ -14,6 +14,8 @@ #include "asm/immap_qe.h" #include "qe.h" +#define MPC85xx_DEVDISR_QE_DISABLE 0x1 + qe_map_t *qe_immr = NULL; static qe_snum_t snums[QE_NUM_OF_SNUM]; @@ -317,7 +319,9 @@ int qe_upload_firmware(const struct qe_firmware *firmware) size_t calc_size = sizeof(struct qe_firmware); size_t length; const struct qe_header *hdr; - +#ifdef CONFIG_DEEP_SLEEP + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); +#endif if (!firmware) { printf("Invalid address\n"); return -EINVAL; @@ -330,6 +334,9 @@ int qe_upload_firmware(const struct qe_firmware *firmware) if ((hdr->magic[0] != 'Q') || (hdr->magic[1] != 'E') || (hdr->magic[2] != 'F')) { printf("Not a microcode\n"); +#ifdef CONFIG_DEEP_SLEEP + setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_QE_DISABLE); +#endif return -EPERM; } diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile index 896c8d407e..66becdc782 100644 --- a/drivers/usb/gadget/Makefile +++ b/drivers/usb/gadget/Makefile @@ -18,6 +18,7 @@ obj-$(CONFIG_THOR_FUNCTION) += f_thor.o obj-$(CONFIG_USBDOWNLOAD_GADGET) += g_dnl.o obj-$(CONFIG_DFU_FUNCTION) += f_dfu.o obj-$(CONFIG_USB_GADGET_MASS_STORAGE) += f_mass_storage.o +obj-$(CONFIG_CMD_FASTBOOT) += f_fastboot.o endif ifdef CONFIG_USB_ETHER obj-y += ether.o diff --git a/drivers/usb/gadget/ci_udc.c b/drivers/usb/gadget/ci_udc.c index 02d3fdade8..9cd003636a 100644 --- a/drivers/usb/gadget/ci_udc.c +++ b/drivers/usb/gadget/ci_udc.c @@ -205,13 +205,26 @@ static void ci_invalidate_qtd(int ep_num) static struct usb_request * ci_ep_alloc_request(struct usb_ep *ep, unsigned int gfp_flags) { - struct ci_ep *ci_ep = container_of(ep, struct ci_ep, ep); - return &ci_ep->req; + struct ci_req *ci_req; + + ci_req = memalign(ARCH_DMA_MINALIGN, sizeof(*ci_req)); + if (!ci_req) + return NULL; + + INIT_LIST_HEAD(&ci_req->queue); + ci_req->b_buf = 0; + + return &ci_req->req; } -static void ci_ep_free_request(struct usb_ep *ep, struct usb_request *_req) +static void ci_ep_free_request(struct usb_ep *ep, struct usb_request *req) { - return; + struct ci_req *ci_req; + + ci_req = container_of(req, struct ci_req, req); + if (ci_req->b_buf) + free(ci_req->b_buf); + free(ci_req); } static void ep_enable(int num, int in, int maxpacket) @@ -267,99 +280,102 @@ static int ci_ep_disable(struct usb_ep *ep) return 0; } -static int ci_bounce(struct ci_ep *ep, int in) +static int ci_bounce(struct ci_req *ci_req, int in) { - uint32_t addr = (uint32_t)ep->req.buf; - uint32_t ba; + struct usb_request *req = &ci_req->req; + uint32_t addr = (uint32_t)req->buf; + uint32_t hwaddr; + uint32_t aligned_used_len; /* Input buffer address is not aligned. */ if (addr & (ARCH_DMA_MINALIGN - 1)) goto align; /* Input buffer length is not aligned. */ - if (ep->req.length & (ARCH_DMA_MINALIGN - 1)) + if (req->length & (ARCH_DMA_MINALIGN - 1)) goto align; /* The buffer is well aligned, only flush cache. */ - ep->b_len = ep->req.length; - ep->b_buf = ep->req.buf; + ci_req->hw_len = req->length; + ci_req->hw_buf = req->buf; goto flush; align: - /* Use internal buffer for small payloads. */ - if (ep->req.length <= 64) { - ep->b_len = 64; - ep->b_buf = ep->b_fast; - } else { - ep->b_len = roundup(ep->req.length, ARCH_DMA_MINALIGN); - ep->b_buf = memalign(ARCH_DMA_MINALIGN, ep->b_len); - if (!ep->b_buf) + if (ci_req->b_buf && req->length > ci_req->b_len) { + free(ci_req->b_buf); + ci_req->b_buf = 0; + } + if (!ci_req->b_buf) { + ci_req->b_len = roundup(req->length, ARCH_DMA_MINALIGN); + ci_req->b_buf = memalign(ARCH_DMA_MINALIGN, ci_req->b_len); + if (!ci_req->b_buf) return -ENOMEM; } + ci_req->hw_len = ci_req->b_len; + ci_req->hw_buf = ci_req->b_buf; + if (in) - memcpy(ep->b_buf, ep->req.buf, ep->req.length); + memcpy(ci_req->hw_buf, req->buf, req->length); flush: - ba = (uint32_t)ep->b_buf; - flush_dcache_range(ba, ba + ep->b_len); + hwaddr = (uint32_t)ci_req->hw_buf; + aligned_used_len = roundup(req->length, ARCH_DMA_MINALIGN); + flush_dcache_range(hwaddr, hwaddr + aligned_used_len); return 0; } -static void ci_debounce(struct ci_ep *ep, int in) +static void ci_debounce(struct ci_req *ci_req, int in) { - uint32_t addr = (uint32_t)ep->req.buf; - uint32_t ba = (uint32_t)ep->b_buf; + struct usb_request *req = &ci_req->req; + uint32_t addr = (uint32_t)req->buf; + uint32_t hwaddr = (uint32_t)ci_req->hw_buf; + uint32_t aligned_used_len; - if (in) { - if (addr == ba) - return; /* not a bounce */ - goto free; - } - invalidate_dcache_range(ba, ba + ep->b_len); + if (in) + return; + + aligned_used_len = roundup(req->actual, ARCH_DMA_MINALIGN); + invalidate_dcache_range(hwaddr, hwaddr + aligned_used_len); - if (addr == ba) - return; /* not a bounce */ + if (addr == hwaddr) + return; /* not a bounce */ - memcpy(ep->req.buf, ep->b_buf, ep->req.actual); -free: - /* Large payloads use allocated buffer, free it. */ - if (ep->b_buf != ep->b_fast) - free(ep->b_buf); + memcpy(req->buf, ci_req->hw_buf, req->actual); } -static int ci_ep_queue(struct usb_ep *ep, - struct usb_request *req, gfp_t gfp_flags) +static void ci_ep_submit_next_request(struct ci_ep *ci_ep) { - struct ci_ep *ci_ep = container_of(ep, struct ci_ep, ep); struct ci_udc *udc = (struct ci_udc *)controller.ctrl->hcor; struct ept_queue_item *item; struct ept_queue_head *head; - int bit, num, len, in, ret; + int bit, num, len, in; + struct ci_req *ci_req; + + ci_ep->req_primed = true; + num = ci_ep->desc->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK; in = (ci_ep->desc->bEndpointAddress & USB_DIR_IN) != 0; item = ci_get_qtd(num, in); head = ci_get_qh(num, in); - len = req->length; - ret = ci_bounce(ci_ep, in); - if (ret) - return ret; + ci_req = list_first_entry(&ci_ep->queue, struct ci_req, queue); + len = ci_req->req.length; item->next = TERMINATE; item->info = INFO_BYTES(len) | INFO_IOC | INFO_ACTIVE; - item->page0 = (uint32_t)ci_ep->b_buf; - item->page1 = ((uint32_t)ci_ep->b_buf & 0xfffff000) + 0x1000; - item->page2 = ((uint32_t)ci_ep->b_buf & 0xfffff000) + 0x2000; - item->page3 = ((uint32_t)ci_ep->b_buf & 0xfffff000) + 0x3000; - item->page4 = ((uint32_t)ci_ep->b_buf & 0xfffff000) + 0x4000; + item->page0 = (uint32_t)ci_req->hw_buf; + item->page1 = ((uint32_t)ci_req->hw_buf & 0xfffff000) + 0x1000; + item->page2 = ((uint32_t)ci_req->hw_buf & 0xfffff000) + 0x2000; + item->page3 = ((uint32_t)ci_req->hw_buf & 0xfffff000) + 0x3000; + item->page4 = ((uint32_t)ci_req->hw_buf & 0xfffff000) + 0x4000; ci_flush_qtd(num); head->next = (unsigned) item; head->info = 0; - DBG("ept%d %s queue len %x, buffer %p\n", - num, in ? "in" : "out", len, ci_ep->b_buf); + DBG("ept%d %s queue len %x, req %p, buffer %p\n", + num, in ? "in" : "out", len, ci_req, ci_req->hw_buf); ci_flush_qh(num); if (in) @@ -368,6 +384,29 @@ static int ci_ep_queue(struct usb_ep *ep, bit = EPT_RX(num); writel(bit, &udc->epprime); +} + +static int ci_ep_queue(struct usb_ep *ep, + struct usb_request *req, gfp_t gfp_flags) +{ + struct ci_ep *ci_ep = container_of(ep, struct ci_ep, ep); + struct ci_req *ci_req = container_of(req, struct ci_req, req); + int in, ret; + int __maybe_unused num; + + num = ci_ep->desc->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK; + in = (ci_ep->desc->bEndpointAddress & USB_DIR_IN) != 0; + + ret = ci_bounce(ci_req, in); + if (ret) + return ret; + + DBG("ept%d %s pre-queue req %p, buffer %p\n", + num, in ? "in" : "out", ci_req, ci_req->hw_buf); + list_add_tail(&ci_req->queue, &ci_ep->queue); + + if (!ci_ep->req_primed) + ci_ep_submit_next_request(ci_ep); return 0; } @@ -376,6 +415,8 @@ static void handle_ep_complete(struct ci_ep *ep) { struct ept_queue_item *item; int num, in, len; + struct ci_req *ci_req; + num = ep->desc->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK; in = (ep->desc->bEndpointAddress & USB_DIR_IN) != 0; if (num == 0) @@ -383,20 +424,27 @@ static void handle_ep_complete(struct ci_ep *ep) item = ci_get_qtd(num, in); ci_invalidate_qtd(num); + len = (item->info >> 16) & 0x7fff; if (item->info & 0xff) printf("EP%d/%s FAIL info=%x pg0=%x\n", num, in ? "in" : "out", item->info, item->page0); - len = (item->info >> 16) & 0x7fff; - ep->req.actual = ep->req.length - len; - ci_debounce(ep, in); + ci_req = list_first_entry(&ep->queue, struct ci_req, queue); + list_del_init(&ci_req->queue); + ep->req_primed = false; + + if (!list_empty(&ep->queue)) + ci_ep_submit_next_request(ep); + + ci_req->req.actual = ci_req->req.length - len; + ci_debounce(ci_req, in); - DBG("ept%d %s complete %x\n", - num, in ? "in" : "out", len); - ep->req.complete(&ep->ep, &ep->req); + DBG("ept%d %s req %p, complete %x\n", + num, in ? "in" : "out", ci_req, len); + ci_req->req.complete(&ep->ep, &ci_req->req); if (num == 0) { - ep->req.length = 0; - usb_ep_queue(&ep->ep, &ep->req, 0); + ci_req->req.length = 0; + usb_ep_queue(&ep->ep, &ci_req->req, 0); ep->desc = &ep0_in_desc; } } @@ -405,13 +453,18 @@ static void handle_ep_complete(struct ci_ep *ep) static void handle_setup(void) { - struct usb_request *req = &controller.ep[0].req; + struct ci_ep *ci_ep = &controller.ep[0]; + struct ci_req *ci_req; + struct usb_request *req; struct ci_udc *udc = (struct ci_udc *)controller.ctrl->hcor; struct ept_queue_head *head; struct usb_ctrlrequest r; int status = 0; int num, in, _num, _in, i; char *buf; + + ci_req = list_first_entry(&ci_ep->queue, struct ci_req, queue); + req = &ci_req->req; head = ci_get_qh(0, 0); /* EP0 OUT */ ci_invalidate_qh(0); @@ -424,6 +477,9 @@ static void handle_setup(void) DBG("handle setup %s, %x, %x index %x value %x\n", reqname(r.bRequest), r.bRequestType, r.bRequest, r.wIndex, r.wValue); + list_del_init(&ci_req->queue); + ci_ep->req_primed = false; + switch (SETUP(r.bRequestType, r.bRequest)) { case SETUP(USB_RECIP_ENDPOINT, USB_REQ_CLEAR_FEATURE): _num = r.wIndex & 15; @@ -701,6 +757,8 @@ static int ci_udc_probe(void) /* Init EP 0 */ memcpy(&controller.ep[0].ep, &ci_ep_init[0], sizeof(*ci_ep_init)); controller.ep[0].desc = &ep0_in_desc; + INIT_LIST_HEAD(&controller.ep[0].queue); + controller.ep[0].req_primed = false; controller.gadget.ep0 = &controller.ep[0].ep; INIT_LIST_HEAD(&controller.gadget.ep0->ep_list); @@ -708,6 +766,8 @@ static int ci_udc_probe(void) for (i = 1; i < NUM_ENDPOINTS; i++) { memcpy(&controller.ep[i].ep, &ci_ep_init[1], sizeof(*ci_ep_init)); + INIT_LIST_HEAD(&controller.ep[i].queue); + controller.ep[i].req_primed = false; list_add_tail(&controller.ep[i].ep.ep_list, &controller.gadget.ep_list); } diff --git a/drivers/usb/gadget/ci_udc.h b/drivers/usb/gadget/ci_udc.h index 4425fd9345..23cff56d7e 100644 --- a/drivers/usb/gadget/ci_udc.h +++ b/drivers/usb/gadget/ci_udc.h @@ -77,15 +77,22 @@ struct ci_udc { #define CTRL_TXT_BULK (2 << 18) #define CTRL_RXT_BULK (2 << 2) +struct ci_req { + struct usb_request req; + struct list_head queue; + /* Bounce buffer allocated if needed to align the transfer */ + uint8_t *b_buf; + uint32_t b_len; + /* Buffer for the current transfer. Either req.buf/len or b_buf/len */ + uint8_t *hw_buf; + uint32_t hw_len; +}; + struct ci_ep { struct usb_ep ep; struct list_head queue; + bool req_primed; const struct usb_endpoint_descriptor *desc; - - struct usb_request req; - uint8_t *b_buf; - uint32_t b_len; - uint8_t b_fast[64] __aligned(ARCH_DMA_MINALIGN); }; struct ci_drv { diff --git a/drivers/usb/gadget/f_dfu.c b/drivers/usb/gadget/f_dfu.c index 1b1e1793d9..859fe828de 100644 --- a/drivers/usb/gadget/f_dfu.c +++ b/drivers/usb/gadget/f_dfu.c @@ -175,10 +175,17 @@ static void dnload_request_flush(struct usb_ep *ep, struct usb_request *req) req->length, f_dfu->blk_seq_num); } +static inline int dfu_get_manifest_timeout(struct dfu_entity *dfu) +{ + return dfu->poll_timeout ? dfu->poll_timeout(dfu) : + DFU_MANIFEST_POLL_TIMEOUT; +} + static void handle_getstatus(struct usb_request *req) { struct dfu_status *dstat = (struct dfu_status *)req->buf; struct f_dfu *f_dfu = req->context; + struct dfu_entity *dfu = dfu_get_entity(f_dfu->altsetting); dfu_set_poll_timeout(dstat, 0); @@ -191,7 +198,8 @@ static void handle_getstatus(struct usb_request *req) f_dfu->dfu_state = DFU_STATE_dfuMANIFEST; break; case DFU_STATE_dfuMANIFEST: - dfu_set_poll_timeout(dstat, DFU_MANIFEST_POLL_TIMEOUT); + dfu_set_poll_timeout(dstat, dfu_get_manifest_timeout(dfu)); + break; default: break; } diff --git a/drivers/usb/gadget/f_fastboot.c b/drivers/usb/gadget/f_fastboot.c new file mode 100644 index 0000000000..9dd85b636e --- /dev/null +++ b/drivers/usb/gadget/f_fastboot.c @@ -0,0 +1,513 @@ +/* + * (C) Copyright 2008 - 2009 + * Windriver, <www.windriver.com> + * Tom Rix <Tom.Rix@windriver.com> + * + * Copyright 2011 Sebastian Andrzej Siewior <bigeasy@linutronix.de> + * + * Copyright 2014 Linaro, Ltd. + * Rob Herring <robh@kernel.org> + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#include <common.h> +#include <errno.h> +#include <malloc.h> +#include <linux/usb/ch9.h> +#include <linux/usb/gadget.h> +#include <linux/usb/composite.h> +#include <linux/compiler.h> +#include <version.h> +#include <g_dnl.h> + +#define FASTBOOT_VERSION "0.4" + +#define FASTBOOT_INTERFACE_CLASS 0xff +#define FASTBOOT_INTERFACE_SUB_CLASS 0x42 +#define FASTBOOT_INTERFACE_PROTOCOL 0x03 + +#define RX_ENDPOINT_MAXIMUM_PACKET_SIZE_2_0 (0x0200) +#define RX_ENDPOINT_MAXIMUM_PACKET_SIZE_1_1 (0x0040) +#define TX_ENDPOINT_MAXIMUM_PACKET_SIZE (0x0040) + +/* The 64 defined bytes plus \0 */ +#define RESPONSE_LEN (64 + 1) + +#define EP_BUFFER_SIZE 4096 + +struct f_fastboot { + struct usb_function usb_function; + + /* IN/OUT EP's and correspoinding requests */ + struct usb_ep *in_ep, *out_ep; + struct usb_request *in_req, *out_req; +}; + +static inline struct f_fastboot *func_to_fastboot(struct usb_function *f) +{ + return container_of(f, struct f_fastboot, usb_function); +} + +static struct f_fastboot *fastboot_func; +static unsigned int download_size; +static unsigned int download_bytes; + +static struct usb_endpoint_descriptor fs_ep_in = { + .bLength = USB_DT_ENDPOINT_SIZE, + .bDescriptorType = USB_DT_ENDPOINT, + .bEndpointAddress = USB_DIR_IN, + .bmAttributes = USB_ENDPOINT_XFER_BULK, + .wMaxPacketSize = TX_ENDPOINT_MAXIMUM_PACKET_SIZE, + .bInterval = 0x00, +}; + +static struct usb_endpoint_descriptor fs_ep_out = { + .bLength = USB_DT_ENDPOINT_SIZE, + .bDescriptorType = USB_DT_ENDPOINT, + .bEndpointAddress = USB_DIR_OUT, + .bmAttributes = USB_ENDPOINT_XFER_BULK, + .wMaxPacketSize = RX_ENDPOINT_MAXIMUM_PACKET_SIZE_1_1, + .bInterval = 0x00, +}; + +static struct usb_endpoint_descriptor hs_ep_out = { + .bLength = USB_DT_ENDPOINT_SIZE, + .bDescriptorType = USB_DT_ENDPOINT, + .bEndpointAddress = USB_DIR_OUT, + .bmAttributes = USB_ENDPOINT_XFER_BULK, + .wMaxPacketSize = RX_ENDPOINT_MAXIMUM_PACKET_SIZE_2_0, + .bInterval = 0x00, +}; + +static struct usb_interface_descriptor interface_desc = { + .bLength = USB_DT_INTERFACE_SIZE, + .bDescriptorType = USB_DT_INTERFACE, + .bInterfaceNumber = 0x00, + .bAlternateSetting = 0x00, + .bNumEndpoints = 0x02, + .bInterfaceClass = FASTBOOT_INTERFACE_CLASS, + .bInterfaceSubClass = FASTBOOT_INTERFACE_SUB_CLASS, + .bInterfaceProtocol = FASTBOOT_INTERFACE_PROTOCOL, +}; + +static struct usb_descriptor_header *fb_runtime_descs[] = { + (struct usb_descriptor_header *)&interface_desc, + (struct usb_descriptor_header *)&fs_ep_in, + (struct usb_descriptor_header *)&hs_ep_out, + NULL, +}; + +/* + * static strings, in UTF-8 + */ +static const char fastboot_name[] = "Android Fastboot"; + +static struct usb_string fastboot_string_defs[] = { + [0].s = fastboot_name, + { } /* end of list */ +}; + +static struct usb_gadget_strings stringtab_fastboot = { + .language = 0x0409, /* en-us */ + .strings = fastboot_string_defs, +}; + +static struct usb_gadget_strings *fastboot_strings[] = { + &stringtab_fastboot, + NULL, +}; + +static void rx_handler_command(struct usb_ep *ep, struct usb_request *req); + +static void fastboot_complete(struct usb_ep *ep, struct usb_request *req) +{ + int status = req->status; + if (!status) + return; + printf("status: %d ep '%s' trans: %d\n", status, ep->name, req->actual); +} + +static int fastboot_bind(struct usb_configuration *c, struct usb_function *f) +{ + int id; + struct usb_gadget *gadget = c->cdev->gadget; + struct f_fastboot *f_fb = func_to_fastboot(f); + + /* DYNAMIC interface numbers assignments */ + id = usb_interface_id(c, f); + if (id < 0) + return id; + interface_desc.bInterfaceNumber = id; + + id = usb_string_id(c->cdev); + if (id < 0) + return id; + fastboot_string_defs[0].id = id; + interface_desc.iInterface = id; + + f_fb->in_ep = usb_ep_autoconfig(gadget, &fs_ep_in); + if (!f_fb->in_ep) + return -ENODEV; + f_fb->in_ep->driver_data = c->cdev; + + f_fb->out_ep = usb_ep_autoconfig(gadget, &fs_ep_out); + if (!f_fb->out_ep) + return -ENODEV; + f_fb->out_ep->driver_data = c->cdev; + + hs_ep_out.bEndpointAddress = fs_ep_out.bEndpointAddress; + + return 0; +} + +static void fastboot_unbind(struct usb_configuration *c, struct usb_function *f) +{ + memset(fastboot_func, 0, sizeof(*fastboot_func)); +} + +static void fastboot_disable(struct usb_function *f) +{ + struct f_fastboot *f_fb = func_to_fastboot(f); + + usb_ep_disable(f_fb->out_ep); + usb_ep_disable(f_fb->in_ep); + + if (f_fb->out_req) { + free(f_fb->out_req->buf); + usb_ep_free_request(f_fb->out_ep, f_fb->out_req); + f_fb->out_req = NULL; + } + if (f_fb->in_req) { + free(f_fb->in_req->buf); + usb_ep_free_request(f_fb->in_ep, f_fb->in_req); + f_fb->in_req = NULL; + } +} + +static struct usb_request *fastboot_start_ep(struct usb_ep *ep) +{ + struct usb_request *req; + + req = usb_ep_alloc_request(ep, 0); + if (!req) + return NULL; + + req->length = EP_BUFFER_SIZE; + req->buf = memalign(CONFIG_SYS_CACHELINE_SIZE, EP_BUFFER_SIZE); + if (!req->buf) { + usb_ep_free_request(ep, req); + return NULL; + } + + memset(req->buf, 0, req->length); + return req; +} + +static int fastboot_set_alt(struct usb_function *f, + unsigned interface, unsigned alt) +{ + int ret; + struct usb_composite_dev *cdev = f->config->cdev; + struct usb_gadget *gadget = cdev->gadget; + struct f_fastboot *f_fb = func_to_fastboot(f); + + debug("%s: func: %s intf: %d alt: %d\n", + __func__, f->name, interface, alt); + + /* make sure we don't enable the ep twice */ + if (gadget->speed == USB_SPEED_HIGH) + ret = usb_ep_enable(f_fb->out_ep, &hs_ep_out); + else + ret = usb_ep_enable(f_fb->out_ep, &fs_ep_out); + if (ret) { + puts("failed to enable out ep\n"); + return ret; + } + + f_fb->out_req = fastboot_start_ep(f_fb->out_ep); + if (!f_fb->out_req) { + puts("failed to alloc out req\n"); + ret = -EINVAL; + goto err; + } + f_fb->out_req->complete = rx_handler_command; + + ret = usb_ep_enable(f_fb->in_ep, &fs_ep_in); + if (ret) { + puts("failed to enable in ep\n"); + goto err; + } + + f_fb->in_req = fastboot_start_ep(f_fb->in_ep); + if (!f_fb->in_req) { + puts("failed alloc req in\n"); + ret = -EINVAL; + goto err; + } + f_fb->in_req->complete = fastboot_complete; + + ret = usb_ep_queue(f_fb->out_ep, f_fb->out_req, 0); + if (ret) + goto err; + + return 0; +err: + fastboot_disable(f); + return ret; +} + +static int fastboot_add(struct usb_configuration *c) +{ + struct f_fastboot *f_fb = fastboot_func; + int status; + + debug("%s: cdev: 0x%p\n", __func__, c->cdev); + + if (!f_fb) { + f_fb = memalign(CONFIG_SYS_CACHELINE_SIZE, sizeof(*f_fb)); + if (!f_fb) + return -ENOMEM; + + fastboot_func = f_fb; + memset(f_fb, 0, sizeof(*f_fb)); + } + + f_fb->usb_function.name = "f_fastboot"; + f_fb->usb_function.hs_descriptors = fb_runtime_descs; + f_fb->usb_function.bind = fastboot_bind; + f_fb->usb_function.unbind = fastboot_unbind; + f_fb->usb_function.set_alt = fastboot_set_alt; + f_fb->usb_function.disable = fastboot_disable; + f_fb->usb_function.strings = fastboot_strings; + + status = usb_add_function(c, &f_fb->usb_function); + if (status) { + free(f_fb); + fastboot_func = f_fb; + } + + return status; +} +DECLARE_GADGET_BIND_CALLBACK(usb_dnl_fastboot, fastboot_add); + +int fastboot_tx_write(const char *buffer, unsigned int buffer_size) +{ + struct usb_request *in_req = fastboot_func->in_req; + int ret; + + memcpy(in_req->buf, buffer, buffer_size); + in_req->length = buffer_size; + ret = usb_ep_queue(fastboot_func->in_ep, in_req, 0); + if (ret) + printf("Error %d on queue\n", ret); + return 0; +} + +static int fastboot_tx_write_str(const char *buffer) +{ + return fastboot_tx_write(buffer, strlen(buffer)); +} + +static void compl_do_reset(struct usb_ep *ep, struct usb_request *req) +{ + do_reset(NULL, 0, 0, NULL); +} + +static void cb_reboot(struct usb_ep *ep, struct usb_request *req) +{ + fastboot_func->in_req->complete = compl_do_reset; + fastboot_tx_write_str("OKAY"); +} + +static int strcmp_l1(const char *s1, const char *s2) +{ + if (!s1 || !s2) + return -1; + return strncmp(s1, s2, strlen(s1)); +} + +static void cb_getvar(struct usb_ep *ep, struct usb_request *req) +{ + char *cmd = req->buf; + char response[RESPONSE_LEN]; + const char *s; + + strcpy(response, "OKAY"); + strsep(&cmd, ":"); + if (!cmd) { + fastboot_tx_write_str("FAILmissing var"); + return; + } + + if (!strcmp_l1("version", cmd)) { + strncat(response, FASTBOOT_VERSION, sizeof(response)); + } else if (!strcmp_l1("bootloader-version", cmd)) { + strncat(response, U_BOOT_VERSION, sizeof(response)); + } else if (!strcmp_l1("downloadsize", cmd)) { + char str_num[12]; + + sprintf(str_num, "%08x", CONFIG_USB_FASTBOOT_BUF_SIZE); + strncat(response, str_num, sizeof(response)); + } else if (!strcmp_l1("serialno", cmd)) { + s = getenv("serial#"); + if (s) + strncat(response, s, sizeof(response)); + else + strcpy(response, "FAILValue not set"); + } else { + strcpy(response, "FAILVariable not implemented"); + } + fastboot_tx_write_str(response); +} + +static unsigned int rx_bytes_expected(void) +{ + int rx_remain = download_size - download_bytes; + if (rx_remain < 0) + return 0; + if (rx_remain > EP_BUFFER_SIZE) + return EP_BUFFER_SIZE; + return rx_remain; +} + +#define BYTES_PER_DOT 0x20000 +static void rx_handler_dl_image(struct usb_ep *ep, struct usb_request *req) +{ + char response[RESPONSE_LEN]; + unsigned int transfer_size = download_size - download_bytes; + const unsigned char *buffer = req->buf; + unsigned int buffer_size = req->actual; + + if (req->status != 0) { + printf("Bad status: %d\n", req->status); + return; + } + + if (buffer_size < transfer_size) + transfer_size = buffer_size; + + memcpy((void *)CONFIG_USB_FASTBOOT_BUF_ADDR + download_bytes, + buffer, transfer_size); + + download_bytes += transfer_size; + + /* Check if transfer is done */ + if (download_bytes >= download_size) { + /* + * Reset global transfer variable, keep download_bytes because + * it will be used in the next possible flashing command + */ + download_size = 0; + req->complete = rx_handler_command; + req->length = EP_BUFFER_SIZE; + + sprintf(response, "OKAY"); + fastboot_tx_write_str(response); + + printf("\ndownloading of %d bytes finished\n", download_bytes); + } else { + req->length = rx_bytes_expected(); + if (req->length < ep->maxpacket) + req->length = ep->maxpacket; + } + + if (download_bytes && !(download_bytes % BYTES_PER_DOT)) { + putc('.'); + if (!(download_bytes % (74 * BYTES_PER_DOT))) + putc('\n'); + } + req->actual = 0; + usb_ep_queue(ep, req, 0); +} + +static void cb_download(struct usb_ep *ep, struct usb_request *req) +{ + char *cmd = req->buf; + char response[RESPONSE_LEN]; + + strsep(&cmd, ":"); + download_size = simple_strtoul(cmd, NULL, 16); + download_bytes = 0; + + printf("Starting download of %d bytes\n", download_size); + + if (0 == download_size) { + sprintf(response, "FAILdata invalid size"); + } else if (download_size > CONFIG_USB_FASTBOOT_BUF_SIZE) { + download_size = 0; + sprintf(response, "FAILdata too large"); + } else { + sprintf(response, "DATA%08x", download_size); + req->complete = rx_handler_dl_image; + req->length = rx_bytes_expected(); + if (req->length < ep->maxpacket) + req->length = ep->maxpacket; + } + fastboot_tx_write_str(response); +} + +static void do_bootm_on_complete(struct usb_ep *ep, struct usb_request *req) +{ + char boot_addr_start[12]; + char *bootm_args[] = { "bootm", boot_addr_start, NULL }; + + puts("Booting kernel..\n"); + + sprintf(boot_addr_start, "0x%lx", load_addr); + do_bootm(NULL, 0, 2, bootm_args); + + /* This only happens if image is somehow faulty so we start over */ + do_reset(NULL, 0, 0, NULL); +} + +static void cb_boot(struct usb_ep *ep, struct usb_request *req) +{ + fastboot_func->in_req->complete = do_bootm_on_complete; + fastboot_tx_write_str("OKAY"); +} + +struct cmd_dispatch_info { + char *cmd; + void (*cb)(struct usb_ep *ep, struct usb_request *req); +}; + +static const struct cmd_dispatch_info cmd_dispatch_info[] = { + { + .cmd = "reboot", + .cb = cb_reboot, + }, { + .cmd = "getvar:", + .cb = cb_getvar, + }, { + .cmd = "download:", + .cb = cb_download, + }, { + .cmd = "boot", + .cb = cb_boot, + }, +}; + +static void rx_handler_command(struct usb_ep *ep, struct usb_request *req) +{ + char *cmdbuf = req->buf; + void (*func_cb)(struct usb_ep *ep, struct usb_request *req) = NULL; + int i; + + for (i = 0; i < ARRAY_SIZE(cmd_dispatch_info); i++) { + if (!strcmp_l1(cmd_dispatch_info[i].cmd, cmdbuf)) { + func_cb = cmd_dispatch_info[i].cb; + break; + } + } + + if (!func_cb) + fastboot_tx_write_str("FAILunknown command"); + else + func_cb(ep, req); + + if (req->status == 0) { + *cmdbuf = '\0'; + req->actual = 0; + usb_ep_queue(ep, req, 0); + } +} diff --git a/drivers/usb/gadget/f_thor.c b/drivers/usb/gadget/f_thor.c index feef9e4619..28f215e07c 100644 --- a/drivers/usb/gadget/f_thor.c +++ b/drivers/usb/gadget/f_thor.c @@ -219,21 +219,15 @@ static int download_tail(long long int left, int cnt) } /* - * To store last "packet" DFU storage backend requires dfu_write with - * size parameter equal to 0 + * To store last "packet" or write file from buffer to filesystem + * DFU storage backend requires dfu_flush * * This also frees memory malloc'ed by dfu_get_buf(), so no explicit * need fo call dfu_free_buf() is needed. */ - ret = dfu_write(dfu_entity, transfer_buffer, 0, cnt); - if (ret) - error("DFU write failed [%d] cnt: %d", ret, cnt); - ret = dfu_flush(dfu_entity, transfer_buffer, 0, cnt); - if (ret) { + if (ret) error("DFU flush failed!"); - return ret; - } return ret; } diff --git a/drivers/usb/gadget/storage_common.c b/drivers/usb/gadget/storage_common.c index 74300746b9..02803df23c 100644 --- a/drivers/usb/gadget/storage_common.c +++ b/drivers/usb/gadget/storage_common.c @@ -311,11 +311,7 @@ static struct fsg_lun *fsg_lun_from_dev(struct device *dev) #define DELAYED_STATUS (EP0_BUFSIZE + 999) /* An impossibly large value */ /* Number of buffers we will use. 2 is enough for double-buffering */ -#ifndef CONFIG_CI_UDC #define FSG_NUM_BUFFERS 2 -#else -#define FSG_NUM_BUFFERS 1 /* ci_udc only allows 1 req per ep at present */ -#endif /* Default size of buffer length. */ #define FSG_BUFLEN ((u32)16384) diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c index 6cb4d98668..45062e699b 100644 --- a/drivers/usb/host/ehci-fsl.c +++ b/drivers/usb/host/ehci-fsl.c @@ -104,15 +104,20 @@ int ehci_hcd_init(int index, enum usb_init_type init, if (!strncmp(phy_type, "utmi", 4)) { #if defined(CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY) - setbits_be32(&ehci->control, PHY_CLK_SEL_UTMI); - setbits_be32(&ehci->control, UTMI_PHY_EN); + clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK, + PHY_CLK_SEL_UTMI); + clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK, + UTMI_PHY_EN); udelay(1000); /* delay required for PHY Clk to appear */ #endif out_le32(&(*hcor)->or_portsc[0], PORT_PTS_UTMI); - setbits_be32(&ehci->control, USB_EN); + clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK, + USB_EN); } else { - setbits_be32(&ehci->control, PHY_CLK_SEL_ULPI); - clrsetbits_be32(&ehci->control, UTMI_PHY_EN, USB_EN); + clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK, + PHY_CLK_SEL_ULPI); + clrsetbits_be32(&ehci->control, UTMI_PHY_EN | + CONTROL_REGISTER_W1C_MASK, USB_EN); udelay(1000); /* delay required for PHY Clk to appear */ if (!usb_phy_clk_valid(ehci)) return -EINVAL; diff --git a/drivers/usb/host/ehci-tegra.c b/drivers/usb/host/ehci-tegra.c index 38db18e2c9..33e5ea9ebd 100644 --- a/drivers/usb/host/ehci-tegra.c +++ b/drivers/usb/host/ehci-tegra.c @@ -69,6 +69,7 @@ struct fdt_usb { unsigned enabled:1; /* 1 to enable, 0 to disable */ unsigned has_legacy_mode:1; /* 1 if this port has legacy mode */ unsigned initialized:1; /* has this port already been initialized? */ + enum usb_init_type init_type; enum dr_mode dr_mode; /* dual role mode */ enum periph_id periph_id;/* peripheral id */ struct fdt_gpio_state vbus_gpio; /* GPIO for vbus enable */ @@ -237,29 +238,31 @@ int ehci_get_port_speed(struct ehci_hcor *hcor, uint32_t reg) return PORTSC_PSPD(reg); } -/* Put the port into host mode */ -static void set_host_mode(struct fdt_usb *config) +/* Set up VBUS for host/device mode */ +static void set_up_vbus(struct fdt_usb *config, enum usb_init_type init) { /* - * If we are an OTG port, check if remote host is driving VBus and - * bail out in this case. + * If we are an OTG port initializing in host mode, + * check if remote host is driving VBus and bail out in this case. */ - if (config->dr_mode == DR_MODE_OTG && - (readl(&config->reg->phy_vbus_sensors) & VBUS_VLD_STS)) + if (init == USB_INIT_HOST && + config->dr_mode == DR_MODE_OTG && + (readl(&config->reg->phy_vbus_sensors) & VBUS_VLD_STS)) { + printf("tegrausb: VBUS input active; not enabling as host\n"); return; + } - /* - * If not driving, we set the GPIO to enable VBUS. We assume - * that the pinmux is set up correctly for this. - */ if (fdt_gpio_isvalid(&config->vbus_gpio)) { + int vbus_value; + fdtdec_setup_gpio(&config->vbus_gpio); - gpio_direction_output(config->vbus_gpio.gpio, - (config->vbus_gpio.flags & FDT_GPIO_ACTIVE_LOW) ? - 0 : 1); - debug("set_host_mode: GPIO %d %s\n", config->vbus_gpio.gpio, - (config->vbus_gpio.flags & FDT_GPIO_ACTIVE_LOW) ? - "low" : "high"); + + vbus_value = (init == USB_INIT_HOST) ^ + !!(config->vbus_gpio.flags & FDT_GPIO_ACTIVE_LOW); + gpio_direction_output(config->vbus_gpio.gpio, vbus_value); + + debug("set_up_vbus: GPIO %d %d\n", config->vbus_gpio.gpio, + vbus_value); } } @@ -293,10 +296,44 @@ static const unsigned *get_pll_timing(void) return timing; } +/* select the PHY to use with a USB controller */ +static void init_phy_mux(struct fdt_usb *config, uint pts, + enum usb_init_type init) +{ + struct usb_ctlr *usbctlr = config->reg; + +#if defined(CONFIG_TEGRA20) + if (config->periph_id == PERIPH_ID_USBD) { + clrsetbits_le32(&usbctlr->port_sc1, PTS1_MASK, + PTS_UTMI << PTS1_SHIFT); + clrbits_le32(&usbctlr->port_sc1, STS1); + } else { + clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK, + PTS_UTMI << PTS_SHIFT); + clrbits_le32(&usbctlr->port_sc1, STS); + } +#else + /* Set to Host mode (if applicable) after Controller Reset was done */ + clrsetbits_le32(&usbctlr->usb_mode, USBMODE_CM_HC, + (init == USB_INIT_HOST) ? USBMODE_CM_HC : 0); + /* + * Select PHY interface after setting host mode. + * For device mode, the ordering requirement is not an issue, since + * only the first USB controller supports device mode, and that USB + * controller can only talk to a UTMI PHY, so the PHY selection is + * already made at reset time, so this write is a no-op. + */ + clrsetbits_le32(&usbctlr->hostpc1_devlc, PTS_MASK, + pts << PTS_SHIFT); + clrbits_le32(&usbctlr->hostpc1_devlc, STS); +#endif +} + /* set up the UTMI USB controller with the parameters provided */ -static int init_utmi_usb_controller(struct fdt_usb *config) +static int init_utmi_usb_controller(struct fdt_usb *config, + enum usb_init_type init) { - u32 val; + u32 b_sess_valid_mask, val; int loop_count; const unsigned *timing; struct usb_ctlr *usbctlr = config->reg; @@ -314,6 +351,10 @@ static int init_utmi_usb_controller(struct fdt_usb *config) /* Follow the crystal clock disable by >100ns delay */ udelay(1); + b_sess_valid_mask = (VBUS_B_SESS_VLD_SW_VALUE | VBUS_B_SESS_VLD_SW_EN); + clrsetbits_le32(&usbctlr->phy_vbus_sensors, b_sess_valid_mask, + (init == USB_INIT_DEVICE) ? b_sess_valid_mask : 0); + /* * To Use the A Session Valid for cable detection logic, VBUS_WAKEUP * mux must be switched to actually use a_sess_vld threshold. @@ -485,21 +526,7 @@ static int init_utmi_usb_controller(struct fdt_usb *config) clrbits_le32(&usbctlr->icusb_ctrl, IC_ENB1); /* Select UTMI parallel interface */ -#if defined(CONFIG_TEGRA20) - if (config->periph_id == PERIPH_ID_USBD) { - clrsetbits_le32(&usbctlr->port_sc1, PTS1_MASK, - PTS_UTMI << PTS1_SHIFT); - clrbits_le32(&usbctlr->port_sc1, STS1); - } else { - clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK, - PTS_UTMI << PTS_SHIFT); - clrbits_le32(&usbctlr->port_sc1, STS); - } -#else - clrsetbits_le32(&usbctlr->hostpc1_devlc, PTS_MASK, - PTS_UTMI << PTS_SHIFT); - clrbits_le32(&usbctlr->hostpc1_devlc, STS); -#endif + init_phy_mux(config, PTS_UTMI, init); /* Deassert power down state */ clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_FORCE_PD_POWERDOWN | @@ -529,7 +556,8 @@ static int init_utmi_usb_controller(struct fdt_usb *config) #endif /* set up the ULPI USB controller with the parameters provided */ -static int init_ulpi_usb_controller(struct fdt_usb *config) +static int init_ulpi_usb_controller(struct fdt_usb *config, + enum usb_init_type init) { u32 val; int loop_count; @@ -557,13 +585,7 @@ static int init_ulpi_usb_controller(struct fdt_usb *config) ULPI_CLKOUT_PINMUX_BYP | ULPI_OUTPUT_PINMUX_BYP); /* Select ULPI parallel interface */ -#if defined(CONFIG_TEGRA20) - clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK, - PTS_ULPI << PTS_SHIFT); -#else - clrsetbits_le32(&usbctlr->hostpc1_devlc, PTS_MASK, - PTS_ULPI << PTS_SHIFT); -#endif + init_phy_mux(config, PTS_ULPI, init); /* enable ULPI transceiver */ setbits_le32(&usbctlr->susp_ctrl, ULPI_PHY_ENB); @@ -612,7 +634,8 @@ static int init_ulpi_usb_controller(struct fdt_usb *config) return 0; } #else -static int init_ulpi_usb_controller(struct fdt_usb *config) +static int init_ulpi_usb_controller(struct fdt_usb *config, + enum usb_init_type init) { printf("No code to set up ULPI controller, please enable" "CONFIG_USB_ULPI and CONFIG_USB_ULPI_VIEWPORT"); @@ -765,42 +788,66 @@ int ehci_hcd_init(int index, enum usb_init_type init, config = &port[index]; + switch (init) { + case USB_INIT_HOST: + switch (config->dr_mode) { + case DR_MODE_HOST: + case DR_MODE_OTG: + break; + default: + printf("tegrausb: Invalid dr_mode %d for host mode\n", + config->dr_mode); + return -1; + } + break; + case USB_INIT_DEVICE: + if (config->periph_id != PERIPH_ID_USBD) { + printf("tegrausb: Device mode only supported on first USB controller\n"); + return -1; + } + if (!config->utmi) { + printf("tegrausb: Device mode only supported with UTMI PHY\n"); + return -1; + } + switch (config->dr_mode) { + case DR_MODE_DEVICE: + case DR_MODE_OTG: + break; + default: + printf("tegrausb: Invalid dr_mode %d for device mode\n", + config->dr_mode); + return -1; + } + break; + default: + printf("tegrausb: Unknown USB_INIT_* %d\n", init); + return -1; + } + /* skip init, if the port is already initialized */ - if (config->initialized) + if (config->initialized && config->init_type == init) goto success; - if (config->utmi && init_utmi_usb_controller(config)) { + if (config->utmi && init_utmi_usb_controller(config, init)) { printf("tegrausb: Cannot init port %d\n", index); return -1; } - if (config->ulpi && init_ulpi_usb_controller(config)) { + if (config->ulpi && init_ulpi_usb_controller(config, init)) { printf("tegrausb: Cannot init port %d\n", index); return -1; } - set_host_mode(config); + set_up_vbus(config, init); config->initialized = 1; + config->init_type = init; success: usbctlr = config->reg; *hccr = (struct ehci_hccr *)&usbctlr->cap_length; *hcor = (struct ehci_hcor *)&usbctlr->usb_cmd; - if (controller->has_hostpc) { - /* Set to Host mode after Controller Reset was done */ - clrsetbits_le32(&usbctlr->usb_mode, USBMODE_CM_HC, - USBMODE_CM_HC); - /* Select UTMI parallel interface after setting host mode */ - if (config->utmi) { - clrsetbits_le32((char *)&usbctlr->usb_cmd + - HOSTPC1_DEVLC, PTS_MASK, - PTS_UTMI << PTS_SHIFT); - clrbits_le32((char *)&usbctlr->usb_cmd + - HOSTPC1_DEVLC, STS); - } - } return 0; } diff --git a/drivers/usb/musb-new/musb_gadget_ep0.c b/drivers/usb/musb-new/musb_gadget_ep0.c index 6599d386dc..8c3b0a145a 100644 --- a/drivers/usb/musb-new/musb_gadget_ep0.c +++ b/drivers/usb/musb-new/musb_gadget_ep0.c @@ -576,6 +576,10 @@ static void ep0_txstate(struct musb *musb) } else request = NULL; + /* send it out, triggering a "txpktrdy cleared" irq */ + musb_ep_select(musb->mregs, 0); + musb_writew(regs, MUSB_CSR0, csr); + /* report completions as soon as the fifo's loaded; there's no * win in waiting till this last packet gets acked. (other than * very precise fault reporting, needed by USB TMC; possible with @@ -588,10 +592,6 @@ static void ep0_txstate(struct musb *musb) return; musb->ackpend = 0; } - - /* send it out, triggering a "txpktrdy cleared" irq */ - musb_ep_select(musb->mregs, 0); - musb_writew(regs, MUSB_CSR0, csr); } /* diff --git a/drivers/video/Makefile b/drivers/video/Makefile index c527029241..945f35dc5d 100644 --- a/drivers/video/Makefile +++ b/drivers/video/Makefile @@ -27,6 +27,7 @@ obj-$(CONFIG_VIDEO_BCM2835) += bcm2835.o obj-$(CONFIG_VIDEO_COREBOOT) += coreboot_fb.o obj-$(CONFIG_VIDEO_CT69000) += ct69000.o videomodes.o obj-$(CONFIG_VIDEO_DA8XX) += da8xx-fb.o videomodes.o +obj-$(CONFIG_VIDEO_IMX25LCDC) += imx25lcdc.o videomodes.o obj-$(CONFIG_VIDEO_MB862xx) += mb862xx.o videomodes.o obj-$(CONFIG_VIDEO_MB86R0xGDC) += mb86r0xgdc.o videomodes.o obj-$(CONFIG_VIDEO_MX3) += mx3fb.o videomodes.o diff --git a/drivers/video/imx25lcdc.c b/drivers/video/imx25lcdc.c new file mode 100644 index 0000000000..ef5767baed --- /dev/null +++ b/drivers/video/imx25lcdc.c @@ -0,0 +1,121 @@ +/* + * (C) Copyright 2011 + * Matthias Weisser <weisserm@arcor.de> + * + * SPDX-License-Identifier: GPL-2.0+ + * + * imx25lcdc.c - Graphic interface for i.MX25 lcd controller + */ + +#include <common.h> + +#include <malloc.h> +#include <asm/io.h> +#include <asm/arch/imx-regs.h> +#include <video_fb.h> +#include "videomodes.h" + +/* + * 4MB (at the end of system RAM) + */ +#define VIDEO_MEM_SIZE 0x400000 + +#define FB_SYNC_CLK_INV (1<<16) /* pixel clock inverted */ + +/* + * Graphic Device + */ +static GraphicDevice imx25fb; + +void *video_hw_init(void) +{ + struct lcdc_regs *lcdc = (struct lcdc_regs *)IMX_LCDC_BASE; + struct ccm_regs *ccm = (struct ccm_regs *)IMX_CCM_BASE; + GraphicDevice *pGD = &imx25fb; + char *s; + u32 *videomem; + + memset(pGD, 0, sizeof(GraphicDevice)); + + pGD->gdfIndex = GDF_16BIT_565RGB; + pGD->gdfBytesPP = 2; + pGD->memSize = VIDEO_MEM_SIZE; + pGD->frameAdrs = PHYS_SDRAM + PHYS_SDRAM_SIZE - VIDEO_MEM_SIZE; + + videomem = (u32 *)pGD->frameAdrs; + + s = getenv("videomode"); + if (s != NULL) { + struct ctfb_res_modes var_mode; + u32 lsr, lpcr, lhcr, lvcr; + unsigned long div; + int bpp; + + /* Disable all clocks of the LCDC */ + writel(readl(&ccm->cgr0) & ~((1<<7) | (1<<24)), &ccm->cgr0); + writel(readl(&ccm->cgr1) & ~(1<<29), &ccm->cgr1); + + bpp = video_get_params(&var_mode, s); + + if (bpp == 0) { + var_mode.xres = 320; + var_mode.yres = 240; + var_mode.pixclock = 154000; + var_mode.left_margin = 68; + var_mode.right_margin = 20; + var_mode.upper_margin = 4; + var_mode.lower_margin = 18; + var_mode.hsync_len = 40; + var_mode.vsync_len = 6; + var_mode.sync = 0; + var_mode.vmode = 0; + } + + /* Fill memory with white */ + memset(videomem, 0xFF, var_mode.xres * var_mode.yres * 2); + + imx25fb.winSizeX = var_mode.xres; + imx25fb.winSizeY = var_mode.yres; + + /* LCD base clock is 66.6MHZ. We do calculations in kHz */ + div = 66000 / (1000000000L / var_mode.pixclock); + if (div > 63) + div = 63; + if (0 == div) + div = 1; + + lsr = ((var_mode.xres / 16) << 20) | + var_mode.yres; + lpcr = (1 << 31) | + (1 << 30) | + (5 << 25) | + (1 << 23) | + (1 << 22) | + (1 << 19) | + (1 << 7) | + div; + lhcr = (var_mode.right_margin << 0) | + (var_mode.left_margin << 8) | + (var_mode.hsync_len << 26); + + lvcr = (var_mode.lower_margin << 0) | + (var_mode.upper_margin << 8) | + (var_mode.vsync_len << 26); + + writel((uint32_t)videomem, &lcdc->lssar); + writel(lsr, &lcdc->lsr); + writel(var_mode.xres * 2 / 4, &lcdc->lvpwr); + writel(lpcr, &lcdc->lpcr); + writel(lhcr, &lcdc->lhcr); + writel(lvcr, &lcdc->lvcr); + writel(0x00040060, &lcdc->ldcr); + + writel(0xA90300, &lcdc->lpccr); + + /* Ensable all clocks of the LCDC */ + writel(readl(&ccm->cgr0) | ((1<<7) | (1<<24)), &ccm->cgr0); + writel(readl(&ccm->cgr1) | (1<<29), &ccm->cgr1); + } + + return pGD; +} diff --git a/include/android_image.h b/include/android_image.h new file mode 100644 index 0000000000..094d60afe8 --- /dev/null +++ b/include/android_image.h @@ -0,0 +1,69 @@ +/* + * This is from the Android Project, + * Repository: https://android.googlesource.com/platform/bootable/bootloader/legacy + * File: include/boot/bootimg.h + * Commit: 4205b865141ff2e255fe1d3bd16de18e217ef06a + * + * Copyright (C) 2008 The Android Open Source Project + * + * SPDX-License-Identifier: BSD-2-Clause + */ + +#ifndef _ANDROID_IMAGE_H_ +#define _ANDROID_IMAGE_H_ + +#define ANDR_BOOT_MAGIC "ANDROID!" +#define ANDR_BOOT_MAGIC_SIZE 8 +#define ANDR_BOOT_NAME_SIZE 16 +#define ANDR_BOOT_ARGS_SIZE 512 + +struct andr_img_hdr { + char magic[ANDR_BOOT_MAGIC_SIZE]; + + u32 kernel_size; /* size in bytes */ + u32 kernel_addr; /* physical load addr */ + + u32 ramdisk_size; /* size in bytes */ + u32 ramdisk_addr; /* physical load addr */ + + u32 second_size; /* size in bytes */ + u32 second_addr; /* physical load addr */ + + u32 tags_addr; /* physical addr for kernel tags */ + u32 page_size; /* flash page size we assume */ + u32 unused[2]; /* future expansion: should be 0 */ + + char name[ANDR_BOOT_NAME_SIZE]; /* asciiz product name */ + + char cmdline[ANDR_BOOT_ARGS_SIZE]; + + u32 id[8]; /* timestamp / checksum / sha1 / etc */ +}; + +/* + * +-----------------+ + * | boot header | 1 page + * +-----------------+ + * | kernel | n pages + * +-----------------+ + * | ramdisk | m pages + * +-----------------+ + * | second stage | o pages + * +-----------------+ + * + * n = (kernel_size + page_size - 1) / page_size + * m = (ramdisk_size + page_size - 1) / page_size + * o = (second_size + page_size - 1) / page_size + * + * 0. all entities are page_size aligned in flash + * 1. kernel and ramdisk are required (size != 0) + * 2. second is optional (second_size == 0 -> no second) + * 3. load each element (kernel, ramdisk, second) at + * the specified physical address (kernel_addr, etc) + * 4. prepare tags at tag_addr. kernel_args[] is + * appended to the kernel commandline in the tags. + * 5. r0 = 0, r1 = MACHINE_TYPE, r2 = tags_addr + * 6. if second_size != 0: jump to second_addr + * else: jump to kernel_addr + */ +#endif diff --git a/include/common.h b/include/common.h index 2adf5f90b8..232136c0cd 100644 --- a/include/common.h +++ b/include/common.h @@ -729,9 +729,12 @@ void get_sys_info ( sys_info_t * ); #if defined(CONFIG_8xx) || defined(CONFIG_MPC8260) void cpu_init_f (volatile immap_t *immr); #endif -#if defined(CONFIG_4xx) || defined(CONFIG_MPC85xx) || defined(CONFIG_MCF52x2) ||defined(CONFIG_MPC86xx) +#if defined(CONFIG_4xx) || defined(CONFIG_MCF52x2) || defined(CONFIG_MPC86xx) void cpu_init_f (void); #endif +#ifdef CONFIG_MPC85xx +ulong cpu_init_f(void); +#endif int cpu_init_r (void); #if defined(CONFIG_MPC8260) @@ -833,7 +836,7 @@ int ctrlc (void); int had_ctrlc (void); /* have we had a Control-C since last clear? */ void clear_ctrlc (void); /* clear the Control-C condition */ int disable_ctrlc (int); /* 1 to disable, 0 to enable Control-C detect */ - +int confirm_yesno(void); /* 1 if input is "y", "Y", "yes" or "YES" */ /* * STDIO based functions (can always be used) */ diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h index df371b771d..1af9ba686d 100644 --- a/include/configs/B4860QDS.h +++ b/include/configs/B4860QDS.h @@ -7,6 +7,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * B4860 QDS board configuration file */ @@ -115,6 +118,17 @@ #define IDT_SERDES1_ADDRESS 0x6E #define IDT_SERDES2_ADDRESS 0x6C +/* Voltage monitor on channel 2*/ +#define I2C_MUX_CH_VOL_MONITOR 0xa +#define I2C_VOL_MONITOR_ADDR 0x40 +#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 +#define I2C_VOL_MONITOR_BUS_V_OVF 0x1 +#define I2C_VOL_MONITOR_BUS_V_SHIFT 3 + +#define CONFIG_ZM7300 +#define I2C_MUX_CH_DPM 0xa +#define I2C_DPM_ADDR 0x28 + #define CONFIG_ENV_OVERWRITE #ifdef CONFIG_SYS_NO_FLASH @@ -547,15 +561,15 @@ unsigned long get_board_ddr_clk(void); * for slave u-boot IMAGE instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull /* * for slave UCODE and ENV instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ @@ -824,8 +838,7 @@ unsigned long get_board_ddr_clk(void); "ramdiskfile=b4860qds/ramdisk.uboot\0" \ "fdtaddr=c00000\0" \ "fdtfile=b4860qds/b4860qds.dtb\0" \ - "bdev=sda3\0" \ - "c=ffe\0" + "bdev=sda3\0" /* For emulation this causes u-boot to jump to the start of the proof point app code automatically */ diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h index e76a04b262..7bb5d33d0c 100644 --- a/include/configs/BSC9132QDS.h +++ b/include/configs/BSC9132QDS.h @@ -360,7 +360,7 @@ combinations. this should be removed later #endif /* Set up IFC registers for boot location NOR/NAND */ -#if defined(CONFIG_NAND) +#if defined(CONFIG_NAND) || defined(CONFIG_NAND_SECBOOT) #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h index 2822a08c0a..fd6c9763d8 100644 --- a/include/configs/GEN860T.h +++ b/include/configs/GEN860T.h @@ -219,6 +219,7 @@ #define CONFIG_CMD_ELF #define CONFIG_CMD_DATE #define CONFIG_CMD_FPGA +#define CONFIG_CMD_FPGA_LOADMK #define CONFIG_CMD_MII #define CONFIG_CMD_BEDBUG diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index f15e1626f0..72f5fde16a 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -11,6 +11,8 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO #include "../board/freescale/common/ics307_clk.h" #ifdef CONFIG_36BIT diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index 7b63945888..48ae9d4cae 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -11,6 +11,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + #include "../board/freescale/common/ics307_clk.h" #ifdef CONFIG_36BIT @@ -30,7 +33,7 @@ #endif #ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xeff80000 +#define CONFIG_SYS_TEXT_BASE 0xeff40000 #endif #ifndef CONFIG_RESET_VECTOR_ADDRESS diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 7443acec80..a0d7d52627 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -16,6 +16,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* High Level Configuration Options */ #define CONFIG_MPC8641 1 /* MPC8641 specific */ #define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */ diff --git a/include/configs/MVBC_P.h b/include/configs/MVBC_P.h index 036396c781..1ab2b3d51a 100644 --- a/include/configs/MVBC_P.h +++ b/include/configs/MVBC_P.h @@ -89,6 +89,7 @@ #define CONFIG_CMD_SDRAM #define CONFIG_CMD_PCI #define CONFIG_CMD_FPGA +#define CONFIG_CMD_FPGA_LOADMK #define CONFIG_CMD_I2C #undef CONFIG_WATCHDOG diff --git a/include/configs/MVBLM7.h b/include/configs/MVBLM7.h index 27c2fa011d..1ee4d7cc33 100644 --- a/include/configs/MVBLM7.h +++ b/include/configs/MVBLM7.h @@ -267,6 +267,7 @@ #define CONFIG_CMD_PCI #define CONFIG_CMD_I2C #define CONFIG_CMD_FPGA +#define CONFIG_CMD_FPGA_LOADMK #define CONFIG_CMD_USB #define CONFIG_DOS_PARTITION diff --git a/include/configs/MVSMR.h b/include/configs/MVSMR.h index ad15506fad..27f730d84b 100644 --- a/include/configs/MVSMR.h +++ b/include/configs/MVSMR.h @@ -74,6 +74,7 @@ #define CONFIG_CMD_CACHE #define CONFIG_CMD_DHCP #define CONFIG_CMD_FPGA +#define CONFIG_CMD_FPGA_LOADMK #define CONFIG_CMD_I2C #define CONFIG_CMD_MII #define CONFIG_CMD_NET diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h index 0f04067258..110ba5f325 100644 --- a/include/configs/P1_P2_RDB.h +++ b/include/configs/P1_P2_RDB.h @@ -20,39 +20,119 @@ #ifdef CONFIG_P1011RDB #define CONFIG_P1011 +#define CONFIG_SYS_L2_SIZE (256 << 10) #endif #ifdef CONFIG_P1020RDB #define CONFIG_P1020 +#define CONFIG_SYS_L2_SIZE (256 << 10) #endif #ifdef CONFIG_P2010RDB #define CONFIG_P2010 +#define CONFIG_SYS_L2_SIZE (512 << 10) #endif #ifdef CONFIG_P2020RDB #define CONFIG_P2020 -#endif - -#ifdef CONFIG_NAND -#define CONFIG_NAND_U_BOOT 1 -#define CONFIG_RAMBOOT_NAND 1 -#ifdef CONFIG_NAND_SPL -#define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */ -#else -#define CONFIG_SYS_LDSCRIPT $(CPUDIR)/u-boot-nand.lds -#define CONFIG_SYS_TEXT_BASE 0xf8f82000 -#endif /* CONFIG_NAND_SPL */ +#define CONFIG_SYS_L2_SIZE (512 << 10) #endif #ifdef CONFIG_SDCARD -#define CONFIG_RAMBOOT_SDCARD 1 -#define CONFIG_SYS_TEXT_BASE 0x11000000 -#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc +#define CONFIG_SPL +#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_MMC_MINIMAL +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SYS_TEXT_BASE 0x11001000 +#define CONFIG_SPL_TEXT_BASE 0xf8f81000 +#define CONFIG_SPL_PAD_TO 0x20000 +#define CONFIG_SPL_MAX_SIZE (128 * 1024) +#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) +#define CONFIG_SYS_MMC_U_BOOT_DST (0x11000000) +#define CONFIG_SYS_MMC_U_BOOT_START (0x11000000) +#define CONFIG_SYS_MMC_U_BOOT_OFFS (129 << 10) +#define CONFIG_SYS_MPC85XX_NO_RESETVEC +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" +#define CONFIG_SPL_MMC_BOOT +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SPL_COMMON_INIT_DDR +#endif #endif #ifdef CONFIG_SPIFLASH -#define CONFIG_RAMBOOT_SPIFLASH 1 -#define CONFIG_SYS_TEXT_BASE 0x11000000 -#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc +#define CONFIG_SPL +#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_FLASH_MINIMAL +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SYS_TEXT_BASE 0x11001000 +#define CONFIG_SPL_TEXT_BASE 0xf8f81000 +#define CONFIG_SPL_PAD_TO 0x20000 +#define CONFIG_SPL_MAX_SIZE (128 * 1024) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x11000000) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x11000000) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (128 << 10) +#define CONFIG_SYS_MPC85XX_NO_RESETVEC +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" +#define CONFIG_SPL_SPI_BOOT +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SPL_COMMON_INIT_DDR +#endif +#endif + +#ifdef CONFIG_NAND +#define CONFIG_SPL +#define CONFIG_TPL +#ifdef CONFIG_TPL_BUILD +#define CONFIG_SPL_NAND_BOOT +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_NAND_INIT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT +#define CONFIG_SPL_COMMON_INIT_DDR +#define CONFIG_SPL_MAX_SIZE (128 << 10) +#define CONFIG_SPL_TEXT_BASE 0xf8f81000 +#define CONFIG_SYS_MPC85XX_NO_RESETVEC +#define CONFIG_SYS_NAND_U_BOOT_SIZE (832 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000) +#define CONFIG_SYS_NAND_U_BOOT_START (0x11000000) +#define CONFIG_SYS_NAND_U_BOOT_OFFS ((128 + 128) << 10) +#elif defined(CONFIG_SPL_BUILD) +#define CONFIG_SPL_INIT_MINIMAL +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SPL_TEXT_BASE 0xff800000 +#define CONFIG_SPL_MAX_SIZE 4096 +#define CONFIG_SYS_NAND_U_BOOT_SIZE (128 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST 0xf8f80000 +#define CONFIG_SYS_NAND_U_BOOT_START 0xf8f80000 +#define CONFIG_SYS_NAND_U_BOOT_OFFS (128 << 10) +#endif /* not CONFIG_TPL_BUILD */ + +#define CONFIG_SPL_PAD_TO 0x20000 +#define CONFIG_TPL_PAD_TO 0x20000 +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SYS_TEXT_BASE 0x11001000 +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" #endif #ifndef CONFIG_SYS_TEXT_BASE @@ -64,8 +144,12 @@ #endif #ifndef CONFIG_SYS_MONITOR_BASE +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE +#else #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ #endif +#endif /* High Level Configuration Options */ #define CONFIG_BOOKE 1 /* BOOKE */ @@ -120,22 +204,45 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_MEMTEST_END 0x1fffffff #define CONFIG_PANIC_HANG /* do not reset board on panic */ - /* - * Config the L2 Cache as L2 SRAM - */ +/* + * Config the L2 Cache as L2 SRAM +*/ +#if defined(CONFIG_SPL_BUILD) +#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH) #define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_INIT_L2_ADDR_PHYS 0xff8f80000ull +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) +#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000 +#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 112 * 1024) +#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 116 * 1024) +#define CONFIG_SPL_RELOC_STACK_SIZE (32 << 10) +#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 148 * 1024) +#if defined(CONFIG_P2020RDB) +#define CONFIG_SPL_RELOC_MALLOC_SIZE (364 << 10) +#else +#define CONFIG_SPL_RELOC_MALLOC_SIZE (108 << 10) +#endif +#elif defined(CONFIG_NAND) +#ifdef CONFIG_TPL_BUILD +#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) +#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000 +#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 192 * 1024) +#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 208 * 1024) +#define CONFIG_SPL_RELOC_MALLOC_SIZE (48 << 10) +#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 176 * 1024) #else +#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 #define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) +#define CONFIG_SPL_RELOC_TEXT_BASE (CONFIG_SYS_INIT_L2_END - 0x2000) +#define CONFIG_SPL_RELOC_STACK ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) +#endif /* CONFIG_TPL_BUILD */ +#endif #endif -#define CONFIG_SYS_L2_SIZE (512 << 10) -#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) - -#define CONFIG_SYS_CCSRBAR 0xffe00000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR -#if defined(CONFIG_NAND_SPL) +#ifdef CONFIG_SPL_BUILD #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE #endif @@ -146,7 +253,15 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_MEM_INIT_VALUE 0xDeadBeef -#define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR size on P1_P2 RDBs */ +#if defined(CONFIG_P1011RDB) || defined(CONFIG_P1020RDB) +/* + * P1020 and it's derivatives support max 32bit DDR width + * So Reduce available DDR size +*/ +#define CONFIG_SYS_SDRAM_SIZE 512 +#else +#define CONFIG_SYS_SDRAM_SIZE 1024 +#endif #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE @@ -201,14 +316,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#if defined(CONFIG_RAMBOOT_NAND) || defined(CONFIG_RAMBOOT_SDCARD) || \ - defined(CONFIG_RAMBOOT_SPIFLASH) -#define CONFIG_SYS_RAMBOOT -#define CONFIG_SYS_EXTRA_ENV_RELOC -#else -#undef CONFIG_SYS_RAMBOOT -#endif - #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_EMPTY_INFO @@ -241,21 +348,12 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_MONITOR_LEN (768 * 1024) #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/ -#ifndef CONFIG_NAND_SPL -#define CONFIG_SYS_NAND_BASE 0xffa00000 +#define CONFIG_SYS_NAND_BASE 0xff800000 #ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull +#define CONFIG_SYS_NAND_BASE_PHYS 0xfff800000ull #else #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE #endif -#else -#define CONFIG_SYS_NAND_BASE 0xfff00000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_NAND_BASE_PHYS 0xffff00000ull -#else -#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE -#endif -#endif #define CONFIG_CMD_NAND #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} @@ -264,15 +362,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_NAND_FSL_ELBC 1 #define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024) -/* NAND boot: 4K NAND loader config */ -#define CONFIG_SYS_NAND_SPL_SIZE 0x1000 -#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) - 0x2000) -#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR) -#define CONFIG_SYS_NAND_U_BOOT_START (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE) -#define CONFIG_SYS_NAND_U_BOOT_OFFS (0) -#define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000) -#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) - /* NAND flash config */ #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ @@ -288,7 +377,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); | OR_FCM_TRLX \ | OR_FCM_EHTR) -#ifdef CONFIG_RAMBOOT_NAND +#ifdef CONFIG_NAND #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #define CONFIG_SYS_BR1_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ @@ -323,7 +412,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#ifdef CONFIG_NAND_SPL +#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL) #define CONFIG_NS16550_MIN_FUNCTIONS #endif @@ -490,33 +579,45 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* * Environment */ -#if defined(CONFIG_SYS_RAMBOOT) -#if defined(CONFIG_RAMBOOT_NAND) - #define CONFIG_ENV_IS_IN_NAND 1 - #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE - #define CONFIG_ENV_OFFSET ((768*1024)+CONFIG_SYS_NAND_BLOCK_SIZE) -#elif defined(CONFIG_RAMBOOT_SDCARD) +#ifdef CONFIG_SPIFLASH +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ +#define CONFIG_ENV_SECT_SIZE 0x10000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10)) +#elif defined(CONFIG_SDCARD) #define CONFIG_ENV_IS_IN_MMC #define CONFIG_FSL_FIXED_MMC_LOCATION -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_SYS_MMC_ENV_DEV 0 -#elif defined(CONFIG_RAMBOOT_SPIFLASH) - #define CONFIG_ENV_IS_IN_SPI_FLASH - #define CONFIG_ENV_SPI_BUS 0 - #define CONFIG_ENV_SPI_CS 0 - #define CONFIG_ENV_SPI_MAX_HZ 10000000 - #define CONFIG_ENV_SPI_MODE 0 - #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ - #define CONFIG_ENV_SECT_SIZE 0x10000 - #define CONFIG_ENV_SIZE 0x2000 -#endif +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_OFFSET (512 * 0x800) +#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10)) +#elif defined(CONFIG_NAND) +#ifdef CONFIG_TPL_BUILD +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10)) #else - #define CONFIG_ENV_IS_IN_FLASH 1 - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) - #define CONFIG_ENV_SIZE 0x2000 - #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#endif +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET (1024 * 1024) +#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) +#elif defined(CONFIG_SYS_RAMBOOT) +#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) +#define CONFIG_ENV_SIZE 0x2000 +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ #endif + #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h index 54e6493913..16f7525def 100644 --- a/include/configs/P2041RDB.h +++ b/include/configs/P2041RDB.h @@ -381,15 +381,15 @@ unsigned long get_board_sys_clk(unsigned long dummy); * for slave u-boot IMAGE instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull /* * for slave UCODE and ENV instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ @@ -713,8 +713,7 @@ unsigned long get_board_sys_clk(unsigned long dummy); "ramdiskfile=p2041rdb/ramdisk.uboot\0" \ "fdtaddr=c00000\0" \ "fdtfile=p2041rdb/p2041rdb.dtb\0" \ - "bdev=sda3\0" \ - "c=ffe\0" + "bdev=sda3\0" #define CONFIG_HDBOOT \ "setenv bootargs root=/dev/$bdev rw " \ diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h index 522653bdc3..2215ac86ab 100644 --- a/include/configs/T1040QDS.h +++ b/include/configs/T1040QDS.h @@ -767,8 +767,7 @@ unsigned long get_board_ddr_clk(void); "ramdiskfile=t1040qds/ramdisk.uboot\0" \ "fdtaddr=c00000\0" \ "fdtfile=t1040qds/t1040qds.dtb\0" \ - "bdev=sda3\0" \ - "c=ffe\0" + "bdev=sda3\0" #define CONFIG_LINUX \ "setenv bootargs root=/dev/ram rw " \ diff --git a/include/configs/T104xRDB.h b/include/configs/T104xRDB.h index 81b4f31bc6..e564cb7f53 100644 --- a/include/configs/T104xRDB.h +++ b/include/configs/T104xRDB.h @@ -779,8 +779,7 @@ "ramdiskfile=" __stringify(RAMDISKFILE) "\0" \ "fdtaddr=c00000\0" \ "fdtfile=" __stringify(FDTFILE) "\0" \ - "bdev=sda3\0" \ - "c=ffe\0" + "bdev=sda3\0" #define CONFIG_LINUX \ "setenv bootargs root=/dev/ram rw " \ diff --git a/include/configs/T208xQDS.h b/include/configs/T208xQDS.h index 8bf08430be..8dd2e492ba 100644 --- a/include/configs/T208xQDS.h +++ b/include/configs/T208xQDS.h @@ -505,15 +505,15 @@ unsigned long get_board_ddr_clk(void); * for slave u-boot IMAGE instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull /* * for slave UCODE and ENV instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ @@ -837,8 +837,7 @@ unsigned long get_board_ddr_clk(void); "ramdiskfile=t2080qds/ramdisk.uboot\0" \ "fdtaddr=c00000\0" \ "fdtfile=t2080qds/t2080qds.dtb\0" \ - "bdev=sda3\0" \ - "c=ffe\0" + "bdev=sda3\0" /* * For emulation this causes u-boot to jump to the start of the diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h index 0be0a0feb0..3a1c49c811 100644 --- a/include/configs/T208xRDB.h +++ b/include/configs/T208xRDB.h @@ -461,15 +461,15 @@ unsigned long get_board_ddr_clk(void); * for slave u-boot IMAGE instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull /* * for slave UCODE and ENV instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ @@ -721,6 +721,7 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_CMD_DHCP #define CONFIG_CMD_ELF +#define CONFIG_CMD_ERRATA #define CONFIG_CMD_MII #define CONFIG_CMD_I2C #define CONFIG_CMD_PING @@ -796,8 +797,7 @@ unsigned long get_board_ddr_clk(void); "ramdiskfile=t2080rdb/ramdisk.uboot\0" \ "fdtaddr=c00000\0" \ "fdtfile=t2080rdb/t2080rdb.dtb\0" \ - "bdev=sda3\0" \ - "c=ffe\0" + "bdev=sda3\0" /* * For emulation this causes u-boot to jump to the start of the diff --git a/include/configs/T4240EMU.h b/include/configs/T4240EMU.h index ad5a9a6f0c..53c69b03db 100644 --- a/include/configs/T4240EMU.h +++ b/include/configs/T4240EMU.h @@ -128,8 +128,7 @@ "ramdiskfile=t4240emu/ramdisk.uboot\0" \ "fdtaddr=c00000\0" \ "fdtfile=t4240emu/t4240emu.dtb\0" \ - "bdev=sda3\0" \ - "c=ffe\0" + "bdev=sda3\0" /* * For emulation this causes u-boot to jump to the start of the proof point diff --git a/include/configs/T4240QDS.h b/include/configs/T4240QDS.h index e4eb30fbeb..a770dd0d3a 100644 --- a/include/configs/T4240QDS.h +++ b/include/configs/T4240QDS.h @@ -375,15 +375,15 @@ unsigned long get_board_ddr_clk(void); * for slave u-boot IMAGE instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull /* * for slave UCODE and ENV instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ @@ -572,8 +572,7 @@ unsigned long get_board_ddr_clk(void); "ramdiskfile=t4240qds/ramdisk.uboot\0" \ "fdtaddr=c00000\0" \ "fdtfile=t4240qds/t4240qds.dtb\0" \ - "bdev=sda3\0" \ - "c=ffe\0" + "bdev=sda3\0" #define CONFIG_HVBOOT \ "setenv bootargs config-addr=0x60000000; " \ diff --git a/include/configs/T4240RDB.h b/include/configs/T4240RDB.h new file mode 100644 index 0000000000..183255d283 --- /dev/null +++ b/include/configs/T4240RDB.h @@ -0,0 +1,756 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * T4240 RDB board configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_T4240RDB +#define CONFIG_PHYS_64BIT + +#define CONFIG_FSL_SATA_V2 +#define CONFIG_PCIE4 + +#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ + +#ifdef CONFIG_RAMBOOT_PBL +#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t4rdb/t4_pbi.cfg +#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t4rdb/t4_rcw.cfg +#endif + +#define CONFIG_DDR_ECC + +#define CONFIG_CMD_REGINFO + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_E500MC /* BOOKE e500mc family */ +#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ +#define CONFIG_MP /* support multiple processors */ + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff40000 +#endif + +#ifndef CONFIG_RESET_VECTOR_ADDRESS +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc +#endif + +#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ +#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS +#define CONFIG_FSL_IFC /* Enable IFC Support */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_PCIE2 /* PCIE controler 2 */ +#define CONFIG_PCIE3 /* PCIE controler 3 */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +#define CONFIG_ENV_OVERWRITE + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_SYS_CACHE_STASHING +#define CONFIG_BTB /* toggle branch predition */ +#ifdef CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#endif + +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ + +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* + * Config the L3 Cache as L3 SRAM + */ +#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE + +#define CONFIG_SYS_DCSRBAR 0xf0000000 +#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull + +/* + * DDR Setup + */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */ +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 4 +#define CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE + +#define CONFIG_DDR_SPD +#define CONFIG_SYS_FSL_DDR3 + + +/* + * IFC Definitions + */ +#define CONFIG_SYS_FLASH_BASE 0xe0000000 +#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) + + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ +#define CONFIG_MISC_INIT_R + +#define CONFIG_HWCONFIG + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 1, direct to uli, tgtid 3, Base address 20000 */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +/* controller 2, Slot 2, tgtid 2, Base address 201000 */ +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ + +/* controller 3, Slot 1, tgtid 1, Base address 202000 */ +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ + +/* controller 4, Base address 203000 */ +#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull +#define CONFIG_SYS_PCIE4_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull +#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ + +#ifdef CONFIG_PCI +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_E1000 + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif /* CONFIG_PCI */ + +/* SATA */ +#ifdef CONFIG_FSL_SATA_V2 +#define CONFIG_LIBATA +#define CONFIG_FSL_SATA + +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SATA2 +#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA + +#define CONFIG_LBA48 +#define CONFIG_CMD_SATA +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +#endif + +#ifdef CONFIG_FMAN_ENET +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC1" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* + * Environment + */ +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ERRATA +#define CONFIG_CMD_GREPENV +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SETEXPR + +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_HVBOOT \ + "setenv bootargs config-addr=0x60000000; " \ + "bootm 0x01000000 - 0x00f00000" + +#ifdef CONFIG_SYS_NO_FLASH +#ifndef CONFIG_RAMBOOT_PBL +#define CONFIG_ENV_IS_NOWHERE +#endif +#else +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#endif + +#if defined(CONFIG_SPIFLASH) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ +#define CONFIG_ENV_SECT_SIZE 0x10000 +#elif defined(CONFIG_SDCARD) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_OFFSET (512 * 1658) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (7 * CONFIG_SYS_NAND_BLOCK_SIZE) +#elif defined(CONFIG_ENV_IS_NOWHERE) +#define CONFIG_ENV_SIZE 0x2000 +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif + +#define CONFIG_SYS_CLK_FREQ 66666666 +#define CONFIG_DDR_CLK_FREQ 133333333 + +#ifndef __ASSEMBLY__ +unsigned long get_board_sys_clk(void); +unsigned long get_board_ddr_clk(void); +#endif + +/* + * DDR Setup + */ +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS1 0x52 +#define SPD_EEPROM_ADDRESS2 0x54 +#define SPD_EEPROM_ADDRESS3 0x56 +#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */ +#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ + +/* + * IFC Definitions + */ +#define CONFIG_SYS_NOR0_CSPR_EXT (0xf) +#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ + + 0x8000000) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR1_CSPR_EXT (0xf) +#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) +/* NOR Flash Timing Params */ +#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 + +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ + FTIM0_NOR_TEADC(0x5) | \ + FTIM0_NOR_TEAHC(0x5)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ + FTIM1_NOR_TRAD_NOR(0x1A) |\ + FTIM1_NOR_TSEQRAD_NOR(0x13)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ + FTIM2_NOR_TCH(0x4) | \ + FTIM2_NOR_TWPH(0x0E) | \ + FTIM2_NOR_TWP(0x1c)) +#define CONFIG_SYS_NOR_FTIM3 0x0 + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ + + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} + +/* NAND Flash on IFC */ +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_MAX_ECCPOS 256 +#define CONFIG_SYS_NAND_MAX_OOBFREE 2 +#define CONFIG_SYS_NAND_BASE 0xff800000 +#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) + +#define CONFIG_SYS_NAND_CSPR_EXT (0xf) +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ + | CSPR_MSEL_NAND /* MSEL = NAND */ \ + | CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) + +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ + | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ + | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ + | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \ + | CSOR_NAND_PB(128)) /*Page Per Block = 128*/ + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +/* ONFI NAND Flash mode0 Timing Params */ +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ + FTIM0_NAND_TWP(0x18) | \ + FTIM0_NAND_TWCHT(0x07) | \ + FTIM0_NAND_TWH(0x0a)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ + FTIM1_NAND_TWBE(0x39) | \ + FTIM1_NAND_TRR(0x0e) | \ + FTIM1_NAND_TRP(0x18)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ + FTIM2_NAND_TREH(0x0a) | \ + FTIM2_NAND_TWHRE(0x1e)) +#define CONFIG_SYS_NAND_FTIM3 0x0 + +#define CONFIG_SYS_NAND_DDR_LAW 11 +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND + +#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) + +#if defined(CONFIG_NAND) +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 +#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 +#else +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 +#endif +#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT +#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR +#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 + +#if defined(CONFIG_RAMBOOT_PBL) +#define CONFIG_SYS_RAMBOOT +#endif + + +/* I2C */ +#define CONFIG_SYS_FSL_I2C_SPEED 100000 /* I2C speed */ +#define CONFIG_SYS_FSL_I2C2_SPEED 100000 /* I2C2 speed */ +#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ +#define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */ + +#define I2C_MUX_CH_DEFAULT 0x8 +#define I2C_MUX_CH_VOL_MONITOR 0xa +#define I2C_MUX_CH_VSC3316_FS 0xc +#define I2C_MUX_CH_VSC3316_BS 0xd + +/* Voltage monitor on channel 2*/ +#define I2C_VOL_MONITOR_ADDR 0x40 +#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 +#define I2C_VOL_MONITOR_BUS_V_OVF 0x1 +#define I2C_VOL_MONITOR_BUS_V_SHIFT 3 + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_FSL_ESPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_SST +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE 0 + + +/* Qman/Bman */ +#ifndef CONFIG_NOBQFMAN +#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ +#define CONFIG_SYS_BMAN_NUM_PORTALS 50 +#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 +#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull +#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 +#define CONFIG_SYS_QMAN_NUM_PORTALS 50 +#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 +#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull +#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 + +#define CONFIG_SYS_DPAA_FMAN +#define CONFIG_SYS_DPAA_PME +#define CONFIG_SYS_PMAN +#define CONFIG_SYS_DPAA_DCE +#define CONFIG_SYS_DPAA_RMAN +#define CONFIG_SYS_INTERLAKEN + +/* Default address of microcode for the Linux Fman driver */ +#if defined(CONFIG_SPIFLASH) +/* + * env is stored at 0x100000, sector size is 0x10000, ucode is stored after + * env, so we got 0x110000. + */ +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_FMAN_FW_ADDR 0x110000 +#elif defined(CONFIG_SDCARD) +/* + * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is + * about 825KB (1650 blocks), Env is stored after the image, and the env size is + * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_MMC +#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_QE_FMAN_FW_IN_NAND +#define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 +#endif +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) +#endif /* CONFIG_NOBQFMAN */ + +#ifdef CONFIG_SYS_DPAA_FMAN +#define CONFIG_FMAN_ENET +#define CONFIG_PHYLIB_10G +#define CONFIG_PHY_VITESSE +#define CONFIG_PHY_CORTINA +#define CONFIG_CORTINA_FW_ADDR 0xefe00000 +#define CONFIG_CORTINA_FW_LENGTH 0x40000 +#define CONFIG_PHY_TERANETICS +#define SGMII_PHY_ADDR1 0x0 +#define SGMII_PHY_ADDR2 0x1 +#define SGMII_PHY_ADDR3 0x2 +#define SGMII_PHY_ADDR4 0x3 +#define SGMII_PHY_ADDR5 0x4 +#define SGMII_PHY_ADDR6 0x5 +#define SGMII_PHY_ADDR7 0x6 +#define SGMII_PHY_ADDR8 0x7 +#define FM1_10GEC1_PHY_ADDR 0x10 +#define FM1_10GEC2_PHY_ADDR 0x11 +#define FM2_10GEC1_PHY_ADDR 0x12 +#define FM2_10GEC2_PHY_ADDR 0x13 +#define CORTINA_PHY_ADDR1 FM1_10GEC1_PHY_ADDR +#define CORTINA_PHY_ADDR2 FM1_10GEC2_PHY_ADDR +#define CORTINA_PHY_ADDR3 FM2_10GEC1_PHY_ADDR +#define CORTINA_PHY_ADDR4 FM2_10GEC2_PHY_ADDR +#endif + + +/* SATA */ +#ifdef CONFIG_FSL_SATA_V2 +#define CONFIG_LIBATA +#define CONFIG_FSL_SATA + +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SATA2 +#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA + +#define CONFIG_LBA48 +#define CONFIG_CMD_SATA +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +#endif + +#ifdef CONFIG_FMAN_ENET +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC1" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* +* USB +*/ +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_CMD_EXT2 +#define CONFIG_HAS_FSL_DR_USB + +#define CONFIG_MMC + +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ + +#define __USB_PHY_TYPE utmi + +/* + * T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be + * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way + * interleaving. It can be cacheline, page, bank, superbank. + * See doc/README.fsl-ddr for details. + */ +#ifdef CONFIG_PPC_T4240 +#define CTRL_INTLV_PREFERED 3way_4KB +#else +#define CTRL_INTLV_PREFERED cacheline +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:" \ + "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ + "bank_intlv=auto;" \ + "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ + "netdev=eth0\0" \ + "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ + "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot && " \ + "protect off $ubootaddr +$filesize && " \ + "erase $ubootaddr +$filesize && " \ + "cp.b $loadaddr $ubootaddr $filesize && " \ + "protect on $ubootaddr +$filesize && " \ + "cmp.b $loadaddr $ubootaddr $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=t4240rdb/ramdisk.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=t4240rdb/t4240rdb.dtb\0" \ + "bdev=sda3\0" + +#define CONFIG_HVBOOT \ + "setenv bootargs config-addr=0x60000000; " \ + "bootm 0x01000000 - 0x00f00000" + +#define CONFIG_LINUX \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "setenv ramdiskaddr 0x02000000;" \ + "setenv fdtaddr 0x00c00000;" \ + "setenv loadaddr 0x1000000;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_HDBOOT \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_LINUX + +#include <asm/fsl_secure_boot.h> + +#ifdef CONFIG_SECURE_BOOT +/* Secure Boot target was not getting build for T4240 because of + * increased binary size. So the size is being reduced by removing USB + * which is anyways not used in Secure Environment. + */ +#undef CONFIG_CMD_USB +#endif + +#endif /* __CONFIG_H */ diff --git a/include/configs/alpr.h b/include/configs/alpr.h index 7849b222b0..2782e559f5 100644 --- a/include/configs/alpr.h +++ b/include/configs/alpr.h @@ -222,6 +222,7 @@ #define CONFIG_CMD_DHCP #define CONFIG_CMD_EEPROM #define CONFIG_CMD_FPGA +#define CONFIG_CMD_FPGA_LOADMK #define CONFIG_CMD_I2C #undef CONFIG_CMD_LOADB #undef CONFIG_CMD_LOADS diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h index d875753a66..fa64a688a4 100644 --- a/include/configs/astro_mcf5373l.h +++ b/include/configs/astro_mcf5373l.h @@ -88,6 +88,7 @@ #define CONFIG_CMD_LOADS #define CONFIG_CMD_LOADB #define CONFIG_CMD_FPGA +#define CONFIG_CMD_FPGA_LOADMK #define CONFIG_CMDLINE_EDITING #define CONFIG_SYS_HUSH_PARSER diff --git a/include/configs/balloon3.h b/include/configs/balloon3.h index 5228ba6ef7..2f5a6609b8 100644 --- a/include/configs/balloon3.h +++ b/include/configs/balloon3.h @@ -54,6 +54,7 @@ #undef CONFIG_CMD_IMLS #define CONFIG_CMD_USB #define CONFIG_CMD_FPGA +#define CONFIG_CMD_FPGA_LOADMK #undef CONFIG_LCD /* diff --git a/include/configs/beaver.h b/include/configs/beaver.h index df9a98bca6..9ff089e67c 100644 --- a/include/configs/beaver.h +++ b/include/configs/beaver.h @@ -21,6 +21,9 @@ #include "tegra30-common.h" +/* VDD core PMIC */ +#define CONFIG_TEGRA_VDD_CORE_TPS62366A_SET1 + /* Enable fdt support for Beaver. Flash the image in u-boot-dtb.bin */ #define CONFIG_DEFAULT_DEVICE_TREE tegra30-beaver #define CONFIG_OF_CONTROL diff --git a/include/configs/cardhu.h b/include/configs/cardhu.h index e15b52737b..59f429cf57 100644 --- a/include/configs/cardhu.h +++ b/include/configs/cardhu.h @@ -21,6 +21,9 @@ #include "tegra30-common.h" +/* VDD core PMIC */ +#define CONFIG_TEGRA_VDD_CORE_TPS62361B_SET3 + /* Enable fdt support for Cardhu. Flash the image in u-boot-dtb.bin */ #define CONFIG_DEFAULT_DEVICE_TREE tegra30-cardhu #define CONFIG_OF_CONTROL diff --git a/include/configs/coreboot.h b/include/configs/coreboot.h index d1d732f211..a1a63a018d 100644 --- a/include/configs/coreboot.h +++ b/include/configs/coreboot.h @@ -167,6 +167,7 @@ #define CONFIG_CMD_ECHO #undef CONFIG_CMD_FLASH #define CONFIG_CMD_FPGA +#define CONFIG_CMD_FPGA_LOADMK #define CONFIG_CMD_GPIO #define CONFIG_CMD_IMI #undef CONFIG_CMD_IMLS diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index db6b9be73c..12b32967b4 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -10,6 +10,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + #include "../board/freescale/common/ics307_clk.h" #ifdef CONFIG_RAMBOOT_PBL @@ -376,15 +379,15 @@ * for slave u-boot IMAGE instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull /* * for slave UCODE and ENV instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ @@ -712,8 +715,7 @@ "ramdiskfile=p4080ds/ramdisk.uboot\0" \ "fdtaddr=c00000\0" \ "fdtfile=p4080ds/p4080ds.dtb\0" \ - "bdev=sda3\0" \ - "c=ffe\0" + "bdev=sda3\0" #define CONFIG_HDBOOT \ "setenv bootargs root=/dev/$bdev rw " \ diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h index 860a11dd2b..b27940995d 100644 --- a/include/configs/da850evm.h +++ b/include/configs/da850evm.h @@ -386,6 +386,7 @@ #define CONFIG_SPL_STACK 0x8001ff00 #define CONFIG_SPL_TEXT_BASE 0x80000000 #define CONFIG_SPL_MAX_FOOTPRINT 32768 +#define CONFIG_SPL_PAD_TO 32768 #endif /* Load U-Boot Image From MMC */ diff --git a/include/configs/draco.h b/include/configs/draco.h new file mode 100644 index 0000000000..a2438d883e --- /dev/null +++ b/include/configs/draco.h @@ -0,0 +1,92 @@ +/* + * (C) Copyright 2013 Siemens Schweiz AG + * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * Based on: + * U-Boot file:/include/configs/am335x_evm.h + * + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_DRACO_H +#define __CONFIG_DRACO_H + +#define CONFIG_SIEMENS_DRACO +#define MACH_TYPE_DRACO 4314 +#define CONFIG_SIEMENS_MACH_TYPE MACH_TYPE_DRACO + +#include "siemens-am33x-common.h" + +#define CONFIG_SYS_MPUCLK 275 +#define DDR_PLL_FREQ 303 +#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC + +#define BOARD_DFU_BUTTON_GPIO 27 +#define BOARD_DFU_BUTTON_LED 64 /* red LED */ +#define BOARD_STATUS_LED 103 /* green LED */ +#define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */ + +#undef CONFIG_DOS_PARTITION +#undef CONFIG_CMD_FAT + + + /* Physical Memory Map */ +#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ + +/* I2C Configuration */ +#define CONFIG_SYS_I2C_SPEED 100000 + +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define EEPROM_ADDR_DDR3 0x90 +#define EEPROM_ADDR_CHIP 0x120 + +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300 + +#undef CONFIG_SPL_NET_SUPPORT +#undef CONFIG_SPL_NET_VCI_STRING +#undef CONFIG_SPL_ETH_SUPPORT + +#undef CONFIG_MII +#undef CONFIG_PHY_GIGE +#define CONFIG_PHY_SMSC + +#define CONFIG_FACTORYSET + +/* Watchdog */ +#define CONFIG_OMAP_WATCHDOG + +#ifndef CONFIG_SPL_BUILD + +/* Default env settings */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "nand_img_size=0x400000\0" \ + "optargs=\0" \ + CONFIG_COMMON_ENV_SETTINGS + +#ifndef CONFIG_RESTORE_FLASH +/* set to negative value for no autoboot */ +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_BOOTCOMMAND \ +"if dfubutton; then " \ + "run dfu_start; " \ + "reset; " \ +"fi;" \ +"run nand_boot;" \ +"reset;" + + +#else +#define CONFIG_BOOTDELAY 0 + +#define CONFIG_BOOTCOMMAND \ + "setenv autoload no; " \ + "dhcp; " \ + "if tftp 80000000 debrick.scr; then " \ + "source 80000000; " \ + "fi" +#endif +#endif /* CONFIG_SPL_BUILD */ +#endif /* ! __CONFIG_DRACO_H */ diff --git a/include/configs/dxr2.h b/include/configs/dxr2.h index 75f7812e7d..76e6cac77c 100644 --- a/include/configs/dxr2.h +++ b/include/configs/dxr2.h @@ -20,12 +20,12 @@ #include "siemens-am33x-common.h" #define CONFIG_SYS_MPUCLK 275 -#define DXR2_IOCTRL_VAL 0x18b #define DDR_PLL_FREQ 303 #undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC #define BOARD_DFU_BUTTON_GPIO 27 -#define BOARD_DFU_BUTTON_LED 64 +#define BOARD_DFU_BUTTON_LED 64 /* red LED */ +#define BOARD_STATUS_LED 103 /* green LED */ #define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */ #undef CONFIG_DOS_PARTITION diff --git a/include/configs/embestmx6boards.h b/include/configs/embestmx6boards.h new file mode 100644 index 0000000000..eb91c44e3f --- /dev/null +++ b/include/configs/embestmx6boards.h @@ -0,0 +1,336 @@ +/* + * Copyright (C) 2014 Eukréa Electromatique + * Author: Eric Bénard <eric@eukrea.com> + * + * Configuration settings for the Embest RIoTboard + * + * based on mx6*sabre*.h which are : + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __RIOTBOARD_CONFIG_H +#define __RIOTBOARD_CONFIG_H + +#include <asm/arch/imx-regs.h> +#include <asm/imx-common/gpio.h> + +#include "mx6_common.h" +#include <linux/sizes.h> + +#define CONFIG_MXC_UART_BASE UART2_BASE +#define CONFIG_CONSOLE_DEV "ttymxc0" +#define CONFIG_MMCROOT "/dev/mmcblk1p2" + +#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) + +#define CONFIG_MX6 + +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_REVISION_TAG + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_LATE_INIT +#define CONFIG_MXC_GPIO + +#define CONFIG_MXC_UART + +#define CONFIG_CMD_FUSE +#ifdef CONFIG_CMD_FUSE +#define CONFIG_MXC_OCOTP +#endif + +/* I2C Configs */ +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_SPEED 100000 + +/* USB Configs */ +#define CONFIG_CMD_USB +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_MX6 +#define CONFIG_USB_STORAGE +#define CONFIG_USB_HOST_ETHER +#define CONFIG_USB_ETHER_ASIX +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */ +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) +#define CONFIG_MXC_USB_FLAGS 0 + +/* MMC Configs */ +#define CONFIG_FSL_ESDHC +#define CONFIG_FSL_USDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR 0 + +#define CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_BOUNCE_BUFFER +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION + +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_FEC_MXC +#define CONFIG_MII +#define IMX_FEC_BASE ENET_BASE_ADDR +#define CONFIG_FEC_XCV_TYPE RGMII +#define CONFIG_ETHPRIME "FEC" +#define CONFIG_FEC_MXC_PHYADDR 4 + +#define CONFIG_PHYLIB +#define CONFIG_PHY_ATHEROS + +#define CONFIG_CMD_SF +#ifdef CONFIG_CMD_SF +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_SST +#define CONFIG_MXC_SPI +#define CONFIG_SF_DEFAULT_BUS 0 +#define CONFIG_SF_DEFAULT_CS (0 | (IMX_GPIO_NR(2, 30) << 8)) +#define CONFIG_SF_DEFAULT_SPEED 20000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#endif + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 + +/* Command definition */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_BMODE +#define CONFIG_CMD_BOOTZ +#define CONFIG_CMD_SETEXPR +#undef CONFIG_CMD_IMLS + +#define CONFIG_BOOTDELAY 1 + +#define CONFIG_LOADADDR 0x12000000 +#define CONFIG_SYS_TEXT_BASE 0x17800000 + +#ifdef CONFIG_SUPPORT_EMMC_BOOT +#define EMMC_ENV \ + "emmcdev=2\0" \ + "update_emmc_firmware=" \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "if ${get_cmd} ${update_sd_firmware_filename}; then " \ + "if mmc dev ${emmcdev}; then " \ + "setexpr fw_sz ${filesize} / 0x200; " \ + "setexpr fw_sz ${fw_sz} + 1; " \ + "mmc write ${loadaddr} 0x2 ${fw_sz}; " \ + "fi; " \ + "fi\0" +#else +#define EMMC_ENV "" +#endif + +#ifdef CONFIG_CMD_SF +#define SF_ENV \ + "update_spi_firmware=" \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "if ${get_cmd} ${update_spi_firmware_filename}; then " \ + "if sf probe; then " \ + "sf erase 0 0xc0000; " \ + "sf write ${loadaddr} 0x400 ${filesize}; " \ + "fi; " \ + "fi\0" +#else +#define SF_ENV "" +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "script=boot.scr\0" \ + "image=zImage\0" \ + "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ + "fdt_addr=0x18000000\0" \ + "boot_fdt=try\0" \ + "ip_dyn=yes\0" \ + "console=" CONFIG_CONSOLE_DEV "\0" \ + "fdt_high=0xffffffff\0" \ + "initrd_high=0xffffffff\0" \ + "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \ + "mmcpart=1\0" \ + "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \ + "update_sd_firmware=" \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "if mmc dev ${mmcdev}; then " \ + "if ${get_cmd} ${update_sd_firmware_filename}; then " \ + "setexpr fw_sz ${filesize} / 0x200; " \ + "setexpr fw_sz ${fw_sz} + 1; " \ + "mmc write ${loadaddr} 0x2 ${fw_sz}; " \ + "fi; " \ + "fi\0" \ + EMMC_ENV \ + SF_ENV \ + "mmcargs=setenv bootargs console=${console},${baudrate} " \ + "root=${mmcroot}\0" \ + "loadbootscript=" \ + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if run loadfdt; then " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootz; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootz; " \ + "fi;\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${image}; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootz; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootz; " \ + "fi;\0" + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev};" \ + "if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loadimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else run netboot; fi" + +#define CONFIG_ARP_TIMEOUT 200UL + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 256 + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_MEMTEST_START 0x10000000 +#define CONFIG_SYS_MEMTEST_END 0x10010000 +#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000 + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR + +#define CONFIG_CMDLINE_EDITING +#define CONFIG_STACKSIZE (128 * 1024) + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* FLASH and environment organization */ +#define CONFIG_SYS_NO_FLASH + +#define CONFIG_ENV_SIZE (8 * 1024) + +#if defined(CONFIG_ENV_IS_IN_MMC) +/* RiOTboard */ +#define CONFIG_DEFAULT_FDT_FILE "imx6s-riotboard.dtb" +#define CONFIG_SYS_FSL_USDHC_NUM 3 +#define CONFIG_SYS_MMC_ENV_DEV 2 /* SDHC4 */ +#define CONFIG_ENV_OFFSET (6 * 64 * 1024) +#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */ +#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH) +/* MarSBoard */ +#define CONFIG_DEFAULT_FDT_FILE "imx6q-marsboard.dtb" +#define CONFIG_SYS_FSL_USDHC_NUM 2 +#define CONFIG_ENV_OFFSET (768 * 1024) +#define CONFIG_ENV_SECT_SIZE (8 * 1024) +#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS +#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS +#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE +#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED +#endif + +#define CONFIG_OF_LIBFDT + +#ifndef CONFIG_SYS_DCACHE_OFF +#define CONFIG_CMD_CACHE +#endif + +/* Framebuffer */ +#define CONFIG_VIDEO +#define CONFIG_VIDEO_IPUV3 +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE +#define CONFIG_VIDEO_BMP_RLE8 +#define CONFIG_SPLASH_SCREEN +#define CONFIG_SPLASH_SCREEN_ALIGN +#define CONFIG_BMP_16BPP +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_BMP_LOGO +#define CONFIG_IPUV3_CLK 260000000 +#define CONFIG_IMX_HDMI +#define CONFIG_IMX_VIDEO_SKIP + +#endif /* __RIOTBOARD_CONFIG_H */ diff --git a/include/configs/exynos5-dt.h b/include/configs/exynos5-dt.h index 414db420dc..5a9b1b42d3 100644 --- a/include/configs/exynos5-dt.h +++ b/include/configs/exynos5-dt.h @@ -288,4 +288,6 @@ #define CONFIG_CMD_BOOTZ +#define CONFIG_CMD_GPIO + #endif /* __CONFIG_H */ diff --git a/include/configs/grsim.h b/include/configs/grsim.h index 556c749f92..1e089a9bf7 100644 --- a/include/configs/grsim.h +++ b/include/configs/grsim.h @@ -53,6 +53,7 @@ #define CONFIG_CMD_DIAG #define CONFIG_CMD_ECHO /* echo arguments */ #define CONFIG_CMD_FPGA /* FPGA configuration Support */ +#define CONFIG_CMD_FPGA_LOADMK #define CONFIG_CMD_IRQ #define CONFIG_CMD_ITEST /* Integer (and string) test */ #define CONFIG_CMD_LOADB /* loadb */ diff --git a/include/configs/grsim_leon2.h b/include/configs/grsim_leon2.h index 8be98983c9..66194a8ff0 100644 --- a/include/configs/grsim_leon2.h +++ b/include/configs/grsim_leon2.h @@ -51,6 +51,7 @@ #define CONFIG_CMD_DIAG #define CONFIG_CMD_ECHO /* echo arguments */ #define CONFIG_CMD_FPGA /* FPGA configuration Support */ +#define CONFIG_CMD_FPGA_LOADMK #define CONFIG_CMD_IRQ #define CONFIG_CMD_ITEST /* Integer (and string) test */ #define CONFIG_CMD_LOADB /* loadb */ diff --git a/include/configs/gw_ventana.h b/include/configs/gw_ventana.h index 33983907f2..cd554957dd 100644 --- a/include/configs/gw_ventana.h +++ b/include/configs/gw_ventana.h @@ -24,6 +24,8 @@ #define CONFIG_SERIAL_TAG #define CONFIG_REVISION_TAG +#define CONFIG_SYS_GENERIC_BOARD + /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024) @@ -136,6 +138,8 @@ #define CONFIG_POWER_I2C #define CONFIG_POWER_PFUZE100 #define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 +#define CONFIG_POWER_LTC3676 +#define CONFIG_POWER_LTC3676_I2C_ADDR 0x3c /* Various command support */ #include <config_cmd_default.h> @@ -190,6 +194,22 @@ #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP #define CONFIG_USB_HUB_MIN_POWER_ON_DELAY 1200 +/* Framebuffer and LCD */ +#define CONFIG_VIDEO +#define CONFIG_VIDEO_IPUV3 +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_VIDEO_BMP_RLE8 +#define CONFIG_SPLASH_SCREEN +#define CONFIG_BMP_16BPP +#define CONFIG_VIDEO_LOGO +#define CONFIG_IPUV3_CLK 260000000 +#define CONFIG_CMD_HDMIDETECT +#define CONFIG_CONSOLE_MUX +#define CONFIG_IMX_HDMI +#define CONFIG_IMX_VIDEO_SKIP + /* serial console (ttymxc1,115200) */ #define CONFIG_CONS_INDEX 1 #define CONFIG_BAUDRATE 115200 diff --git a/include/configs/hummingboard.h b/include/configs/hummingboard.h index 2895523344..34dbdce1a6 100644 --- a/include/configs/hummingboard.h +++ b/include/configs/hummingboard.h @@ -27,6 +27,8 @@ #define CONFIG_INITRD_TAG #define CONFIG_REVISION_TAG +#define CONFIG_SYS_GENERIC_BOARD + /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (2 * SZ_1M) diff --git a/include/configs/iocon.h b/include/configs/iocon.h index f36c2a3504..79c4736bc5 100644 --- a/include/configs/iocon.h +++ b/include/configs/iocon.h @@ -62,7 +62,8 @@ * Commands additional to the ones defined in amcc-common.h */ #define CONFIG_CMD_CACHE -#define CONFIG_CMD_FPGAD +#define CONFIG_CMD_FPGA +#define CONFIG_CMD_FPGA_LOADMK #undef CONFIG_CMD_EEPROM /* diff --git a/include/configs/k2hk_evm.h b/include/configs/k2hk_evm.h index 9bb8f342b6..dde73298fc 100644 --- a/include/configs/k2hk_evm.h +++ b/include/configs/k2hk_evm.h @@ -165,6 +165,7 @@ #define CONFIG_CMD_EEPROM /* U-Boot general configuration */ +#define CONFIG_SYS_GENERIC_BOARD #define CONFIG_SYS_PROMPT "K2HK EVM # " #define CONFIG_SYS_CBSIZE 1024 #define CONFIG_SYS_PBSIZE 2048 diff --git a/include/configs/km/kmp204x-common.h b/include/configs/km/kmp204x-common.h index 418e3d1298..efd96352ec 100644 --- a/include/configs/km/kmp204x-common.h +++ b/include/configs/km/kmp204x-common.h @@ -85,11 +85,7 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_ADDR_MAP #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ -#define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00800000 -#define CONFIG_SYS_ALT_MEMTEST -#define CONFIG_PANIC_HANG /* do not reset board on panic */ +#define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS /* POST memory regions test */ /* * Config the L3 Cache as L3 SRAM @@ -143,10 +139,12 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_KM_PNVRAM 0x80000 /* physical RAM MTD size [hex] */ #define CONFIG_KM_PHRAM 0x100000 -/* resereved pram area at the end of memroy [hex] */ -#define CONFIG_KM_RESERVED_PRAM 0x0 -/* enable protected RAM */ -#define CONFIG_PRAM 0 +/* reserved pram area at the end of memory [hex] + * u-boot reserves some memory for the MP boot page */ +#define CONFIG_KM_RESERVED_PRAM 0x1000 +/* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable + * is not valid yet, which is the case for when u-boot copies itself to RAM */ +#define CONFIG_PRAM ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM)>>10) #define CONFIG_KM_CRAMFS_ADDR 0x2000000 #define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */ @@ -383,6 +381,7 @@ int get_scl(void); */ #define CONFIG_CMD_PCI #define CONFIG_CMD_NET +#define CONFIG_CMD_ERRATA /* we don't need flash support */ #define CONFIG_SYS_NO_FLASH diff --git a/include/configs/koelsch.h b/include/configs/koelsch.h index 90e2d7a030..1a93d1769f 100644 --- a/include/configs/koelsch.h +++ b/include/configs/koelsch.h @@ -32,15 +32,9 @@ #define CONFIG_CMD_NFS #define CONFIG_CMD_BOOTZ -#if defined(CONFIG_SYS_USE_BOOT_NORFLASH) -#define CONFIG_CMD_FLASH -#define CONFIG_SYS_TEXT_BASE 0x00000000 -#else -/* SPI flash boot is default. */ #define CONFIG_CMD_SF #define CONFIG_CMD_SPI #define CONFIG_SYS_TEXT_BASE 0xE6304000 -#endif #define CONFIG_CMDLINE_TAG #define CONFIG_SETUP_MEMORY_TAGS @@ -109,29 +103,6 @@ #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) /* FLASH */ -#if defined(CONFIG_SYS_USE_BOOT_NORFLASH) -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS -#define CONFIG_FLASH_SHOW_PROGRESS 45 -#define CONFIG_SYS_FLASH_BASE 0x00000000 -#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MB */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_FLASH_BANKS_LIST { (CONFIG_SYS_FLASH_BASE) } -#define CONFIG_SYS_FLASH_BANKS_SIZES { (CONFIG_SYS_FLASH_SIZE) } -#define CONFIG_SYS_FLASH_ERASE_TOUT 3000 -#define CONFIG_SYS_FLASH_WRITE_TOUT 3000 -#define CONFIG_SYS_FLASH_LOCK_TOUT 3000 -#define CONFIG_SYS_FLASH_UNLOCK_TOUT 3000 -/* ENV setting */ -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \ - CONFIG_SYS_MONITOR_LEN) - -#else /* CONFIG_SYS_USE_BOOT_NORFLASH */ - #define CONFIG_SYS_NO_FLASH #define CONFIG_SPI #define CONFIG_SH_QSPI @@ -142,8 +113,6 @@ #define CONFIG_ENV_IS_IN_SPI_FLASH #define CONFIG_ENV_ADDR 0xC0000 -#endif /* CONFIG_SYS_USE_BOOT_NORFLASH */ - /* Common ENV setting */ #define CONFIG_ENV_OVERWRITE #define CONFIG_ENV_SECT_SIZE (256 * 1024) @@ -166,8 +135,9 @@ #define CONFIG_SH_ETHER_ALIGNE_SIZE 64 /* Board Clock */ -#define CONFIG_SYS_CLK_FREQ 10000000 -#define CONFIG_SH_TMU_CLK_FREQ CONFIG_SYS_CLK_FREQ +#define RMOBILE_XTAL_CLK 20000000u +#define CONFIG_SYS_CLK_FREQ RMOBILE_XTAL_CLK +#define CONFIG_SH_TMU_CLK_FREQ (CONFIG_SYS_CLK_FREQ / 2) #define CONFIG_SH_SCIF_CLK_FREQ 14745600 #define CONFIG_SYS_TMU_CLK_DIV 4 diff --git a/include/configs/kwb.h b/include/configs/kwb.h index 0f631c0f60..0860434f22 100644 --- a/include/configs/kwb.h +++ b/include/configs/kwb.h @@ -109,7 +109,7 @@ #undef CONFIG_ENV_IS_NOWHERE #define CONFIG_ENV_IS_IN_MMC -#define CONFIG_SYS_MMC_ENV_DEV 1 +#define CONFIG_SYS_MMC_ENV_DEV 0 #define CONFIG_SYS_MMC_ENV_PART 2 #define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */ #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) diff --git a/include/configs/lager.h b/include/configs/lager.h index b420e45e63..ac31128e45 100644 --- a/include/configs/lager.h +++ b/include/configs/lager.h @@ -16,8 +16,6 @@ #define CONFIG_RMOBILE #define CONFIG_RMOBILE_BOARD_STRING "Lager" #define CONFIG_SH_GPIO_PFC -#define MACH_TYPE_LAGER 4538 -#define CONFIG_MACH_TYPE MACH_TYPE_LAGER #include <asm/arch/rmobile.h> @@ -35,14 +33,9 @@ #define CONFIG_CMD_NFS #define CONFIG_CMD_BOOTZ -#if defined(CONFIG_SYS_USE_BOOT_NORFLASH) -#define CONFIG_CMD_FLASH -#define CONFIG_SYS_TEXT_BASE 0x00000000 -#else #define CONFIG_CMD_SF #define CONFIG_CMD_SPI #define CONFIG_SYS_TEXT_BASE 0xE8080000 -#endif #define CONFIG_CMDLINE_TAG #define CONFIG_SETUP_MEMORY_TAGS @@ -111,31 +104,6 @@ #define CONFIG_SYS_MALLOC_LEN (1 * 1024 * 1024) #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) -#if defined(CONFIG_SYS_USE_BOOT_NORFLASH) -/* USE NOR FLASH */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS -#define CONFIG_FLASH_SHOW_PROGRESS 45 -#define CONFIG_SYS_FLASH_BASE 0x00000000 -#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MB */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_FLASH_BANKS_LIST { (CONFIG_SYS_FLASH_BASE) } -#define CONFIG_SYS_FLASH_BANKS_SIZES { (CONFIG_SYS_FLASH_SIZE) } -#define CONFIG_SYS_FLASH_ERASE_TOUT 3000 -#define CONFIG_SYS_FLASH_WRITE_TOUT 3000 -#define CONFIG_SYS_FLASH_LOCK_TOUT 3000 -#define CONFIG_SYS_FLASH_UNLOCK_TOUT 3000 - -/* ENV setting */ -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \ - CONFIG_SYS_MONITOR_LEN) - -#else /* CONFIG_SYS_USE_BOOT_NORFLASH */ - /* USE SPI */ #define CONFIG_SPI #define CONFIG_SPI_FLASH_BAR @@ -147,7 +115,6 @@ /* ENV setting */ #define CONFIG_ENV_IS_IN_SPI_FLASH #define CONFIG_ENV_ADDR 0xC0000 -#endif /* Common ENV setting */ #define CONFIG_ENV_OVERWRITE @@ -186,9 +153,10 @@ #define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */ /* Board Clock */ -#define CONFIG_BASE_CLK_FREQ 20000000u -#define CONFIG_SH_TMU_CLK_FREQ (CONFIG_BASE_CLK_FREQ / 2) /* EXT / 2 */ -#define CONFIG_PLL1_CLK_FREQ (CONFIG_BASE_CLK_FREQ * 156 / 2) +#define RMOBILE_XTAL_CLK 20000000u +#define CONFIG_SYS_CLK_FREQ RMOBILE_XTAL_CLK +#define CONFIG_SH_TMU_CLK_FREQ (CONFIG_SYS_CLK_FREQ / 2) /* EXT / 2 */ +#define CONFIG_PLL1_CLK_FREQ (CONFIG_SYS_CLK_FREQ * 156 / 2) #define CONFIG_PLL1_DIV2_CLK_FREQ (CONFIG_PLL1_CLK_FREQ / 2) #define CONFIG_MP_CLK_FREQ (CONFIG_PLL1_DIV2_CLK_FREQ / 15) #define CONFIG_HP_CLK_FREQ (CONFIG_PLL1_CLK_FREQ / 12) diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h index bb1fa44d80..3e387c42dd 100644 --- a/include/configs/m28evk.h +++ b/include/configs/m28evk.h @@ -7,7 +7,6 @@ #ifndef __CONFIGS_M28EVK_H__ #define __CONFIGS_M28EVK_H__ - /* System configurations */ #define CONFIG_MX28 /* i.MX28 SoC */ #define MACH_TYPE_M28EVK 3613 diff --git a/include/configs/mt_ventoux.h b/include/configs/mt_ventoux.h index e7afd07b94..01e395a49d 100644 --- a/include/configs/mt_ventoux.h +++ b/include/configs/mt_ventoux.h @@ -49,6 +49,7 @@ * FPGA */ #define CONFIG_CMD_FPGA +#define CONFIG_CMD_FPGA_LOADMK #define CONFIG_FPGA #define CONFIG_FPGA_XILINX #define CONFIG_FPGA_SPARTAN3 diff --git a/include/configs/mx53ard.h b/include/configs/mx53ard.h index 797a637bf7..134d6804bc 100644 --- a/include/configs/mx53ard.h +++ b/include/configs/mx53ard.h @@ -23,6 +23,8 @@ #define CONFIG_INITRD_TAG #define CONFIG_REVISION_TAG +#define CONFIG_SYS_GENERIC_BOARD + /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024) diff --git a/include/configs/mx53evk.h b/include/configs/mx53evk.h index 3f0d80ac68..5bbae8cf7d 100644 --- a/include/configs/mx53evk.h +++ b/include/configs/mx53evk.h @@ -23,6 +23,8 @@ #define CONFIG_INITRD_TAG #define CONFIG_REVISION_TAG +#define CONFIG_SYS_GENERIC_BOARD + #define CONFIG_OF_LIBFDT /* Size of malloc() pool */ diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h index 5859f360e0..12d79b4559 100644 --- a/include/configs/mx53loco.h +++ b/include/configs/mx53loco.h @@ -22,6 +22,8 @@ #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_INITRD_TAG +#define CONFIG_SYS_GENERIC_BOARD + /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024) diff --git a/include/configs/mx53smd.h b/include/configs/mx53smd.h index a04e7c7a3e..3da0ef4bd0 100644 --- a/include/configs/mx53smd.h +++ b/include/configs/mx53smd.h @@ -23,6 +23,8 @@ #define CONFIG_INITRD_TAG #define CONFIG_REVISION_TAG +#define CONFIG_SYS_GENERIC_BOARD + /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024) diff --git a/include/configs/mx6sabre_common.h b/include/configs/mx6sabre_common.h index 7a2c172d4a..e59a3b4b05 100644 --- a/include/configs/mx6sabre_common.h +++ b/include/configs/mx6sabre_common.h @@ -25,6 +25,8 @@ #define CONFIG_INITRD_TAG #define CONFIG_REVISION_TAG +#define CONFIG_SYS_GENERIC_BOARD + /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) diff --git a/include/configs/mx6sabresd.h b/include/configs/mx6sabresd.h index 5d02d23ec7..0fa6573c7f 100644 --- a/include/configs/mx6sabresd.h +++ b/include/configs/mx6sabresd.h @@ -47,6 +47,7 @@ #define CONFIG_VIDEO_BMP_LOGO #define CONFIG_IPUV3_CLK 260000000 #define CONFIG_IMX_HDMI +#define CONFIG_IMX_VIDEO_SKIP #define CONFIG_CMD_PCI #ifdef CONFIG_CMD_PCI diff --git a/include/configs/mx6slevk.h b/include/configs/mx6slevk.h index 1876dbf35a..3d05a647d9 100644 --- a/include/configs/mx6slevk.h +++ b/include/configs/mx6slevk.h @@ -10,6 +10,7 @@ #define __CONFIG_H #include <asm/arch/imx-regs.h> +#include <asm/imx-common/gpio.h> #include <linux/sizes.h> #include "mx6_common.h" @@ -196,4 +197,15 @@ #define CONFIG_CMD_CACHE #endif +#define CONFIG_CMD_SF +#ifdef CONFIG_CMD_SF +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_MXC_SPI +#define CONFIG_SF_DEFAULT_BUS 0 +#define CONFIG_SF_DEFAULT_CS (0 | (IMX_GPIO_NR(4, 11) << 8)) +#define CONFIG_SF_DEFAULT_SPEED 20000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#endif + #endif /* __CONFIG_H */ diff --git a/include/configs/mxs.h b/include/configs/mxs.h index ba55177e72..8bce28fe20 100644 --- a/include/configs/mxs.h +++ b/include/configs/mxs.h @@ -40,6 +40,7 @@ /* * CPU specifics */ +#define CONFIG_SYS_GENERIC_BOARD /* MXS uses FDT */ #define CONFIG_OF_LIBFDT diff --git a/include/configs/nitrogen6x.h b/include/configs/nitrogen6x.h index f7e7315a9b..b2b17ce969 100644 --- a/include/configs/nitrogen6x.h +++ b/include/configs/nitrogen6x.h @@ -24,6 +24,7 @@ #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_INITRD_TAG #define CONFIG_REVISION_TAG +#define CONFIG_SYS_GENERIC_BOARD /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024) @@ -141,6 +142,7 @@ #define CONFIG_CMD_HDMIDETECT #define CONFIG_CONSOLE_MUX #define CONFIG_IMX_HDMI +#define CONFIG_IMX_VIDEO_SKIP /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index fae0e6ffcb..0a7df60f28 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -66,6 +66,16 @@ #define CONFIG_TWL4030_USB 1 #define CONFIG_USB_ETHER #define CONFIG_USB_ETHER_RNDIS +#define CONFIG_USB_GADGET +#define CONFIG_USB_GADGET_VBUS_DRAW 0 +#define CONFIG_USBDOWNLOAD_GADGET +#define CONFIG_G_DNL_VENDOR_NUM 0x0451 +#define CONFIG_G_DNL_PRODUCT_NUM 0xd022 +#define CONFIG_G_DNL_MANUFACTURER "TI" +#define CONFIG_CMD_FASTBOOT +#define CONFIG_ANDROID_BOOT_IMAGE +#define CONFIG_USB_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR +#define CONFIG_USB_FASTBOOT_BUF_SIZE 0x07000000 /* USB EHCI */ #define CONFIG_CMD_USB @@ -170,11 +180,17 @@ "if test $beaglerev = C4; then " \ "setenv fdtfile omap3-beagle.dtb; fi; " \ "if test $beaglerev = xMAB; then " \ - "setenv fdtfile omap3-beagle-xm.dtb; fi; " \ + "setenv fdtfile omap3-beagle-xm-ab.dtb; fi; " \ "if test $beaglerev = xMC; then " \ "setenv fdtfile omap3-beagle-xm.dtb; fi; " \ "if test $fdtfile = undefined; then " \ "echo WARNING: Could not determine device tree to use; fi; \0" \ + "validatefdt=" \ + "if test $beaglerev = xMAB; then " \ + "if test ! -e mmc ${bootpart} ${bootdir}/${fdtfile}; then " \ + "setenv fdtfile omap3-beagle-xm.dtb; " \ + "fi; " \ + "fi; \0" \ "bootenv=uEnv.txt\0" \ "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \ "importbootenv=echo Importing environment from mmc ...; " \ @@ -190,7 +206,7 @@ "rootfstype=${ramrootfstype}\0" \ "loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \ "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \ - "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \ + "loadfdt=run validatefdt; load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "bootm ${loadaddr}\0" \ diff --git a/include/configs/omap3_mvblx.h b/include/configs/omap3_mvblx.h index 8d11010f84..a3dcb152d3 100644 --- a/include/configs/omap3_mvblx.h +++ b/include/configs/omap3_mvblx.h @@ -127,6 +127,7 @@ #define CONFIG_CMD_DHCP #define CONFIG_CMD_PING #define CONFIG_CMD_FPGA +#define CONFIG_CMD_FPGA_LOADMK #define CONFIG_SYS_I2C #define CONFIG_SYS_OMAP24_I2C_SPEED 100000 diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h index e745945ba7..185df775aa 100644 --- a/include/configs/p1_p2_rdb_pc.h +++ b/include/configs/p1_p2_rdb_pc.h @@ -10,6 +10,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + #ifdef CONFIG_36BIT #define CONFIG_PHYS_64BIT #endif @@ -883,6 +886,10 @@ #endif #endif +#if defined(CONFIG_P1020RDB_PD) +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 +#endif + #define CONFIG_MMC #ifdef CONFIG_MMC diff --git a/include/configs/pepper.h b/include/configs/pepper.h new file mode 100644 index 0000000000..cc153abaa9 --- /dev/null +++ b/include/configs/pepper.h @@ -0,0 +1,99 @@ +/* + * Copyright (C) 2013 Gumstix, Inc. - http://www.gumstix.com/ + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_PEPPER_H +#define __CONFIG_PEPPER_H + +#define CONFIG_MMC +#include <configs/ti_am335x_common.h> + +#undef CONFIG_BOARD_LATE_INIT +#undef CONFIG_SPL_OS_BOOT + +/* Clock defines */ +#define V_OSCK 24000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK) + +#undef CONFIG_SYS_PROMPT +#define CONFIG_SYS_PROMPT "pepper# " + +/* Mach type */ +#define MACH_TYPE_PEPPER 4207 /* Until the next sync */ +#define CONFIG_MACH_TYPE MACH_TYPE_PEPPER + +#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ +#define CONFIG_ENV_IS_NOWHERE +/* Display cpuinfo */ +#define CONFIG_DISPLAY_CPUINFO + +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG +#define CONFIG_EXTRA_ENV_SETTINGS \ + DEFAULT_LINUX_BOOT_ENV \ + "bootdir=/boot\0" \ + "bootfile=zImage\0" \ + "fdtfile=am335x-pepper.dtb\0" \ + "console=ttyO0,115200n8\0" \ + "optargs=\0" \ + "mmcdev=0\0" \ + "mmcroot=/dev/mmcblk0p2 rw\0" \ + "mmcrootfstype=ext3 rootwait\0" \ + "mmcargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=${mmcroot} " \ + "rootfstype=${mmcrootfstype}\0" \ + "bootenv=uEnv.txt\0" \ + "loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \ + "importbootenv=echo Importing environment from mmc ...; " \ + "env import -t ${loadaddr} ${filesize}\0" \ + "mmcload=load mmc ${mmcdev}:2 ${loadaddr} ${bootdir}/${bootfile}; " \ + "load mmc ${mmcdev}:2 ${fdtaddr} ${bootdir}/${fdtfile}\0" \ + "loaduimage=fatload mmc ${mmcdev}:1 ${loadaddr} uImage\0" \ + "uimageboot=echo Booting from mmc${mmcdev} ...; " \ + "run mmcargs; " \ + "bootm ${loadaddr}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "bootz ${loadaddr} - ${fdtaddr}\0" \ + "ubiboot=echo Booting from nand (ubifs) ...; " \ + "run ubiargs; run ubiload; " \ + "bootz ${loadaddr} - ${fdtaddr}\0" \ + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "echo SD/MMC found on device ${mmcdev};" \ + "if run loadbootenv; then " \ + "echo Loaded environment from ${bootenv};" \ + "run importbootenv;" \ + "fi;" \ + "if test -n $uenvcmd; then " \ + "echo Running uenvcmd ...;" \ + "run uenvcmd;" \ + "fi;" \ + "if run mmcload; then " \ + "run mmcboot;" \ + "fi;" \ + "if run loaduimage; then " \ + "run uimageboot;" \ + "fi;" \ + "fi;" \ + +/* Serial console configuration */ +#define CONFIG_CONS_INDEX 1 /* UART0 */ +#define CONFIG_SERIAL1 1 +#define CONFIG_SYS_NS16550_COM1 0x44e09000 + +/* Ethernet support */ +#define CONFIG_PHY_GIGE +#define CONFIG_PHYLIB +#define CONFIG_PHY_ADDR 0 +#define CONFIG_PHY_MICREL +#define CONFIG_PHY_MICREL_KSZ9021 +#define CONFIG_PHY_RESET_DELAY 1000 + +/* SPL */ +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds" + +#endif /* __CONFIG_PEPPER_H */ diff --git a/include/configs/pxm2.h b/include/configs/pxm2.h index 6276d43395..d75d562963 100644 --- a/include/configs/pxm2.h +++ b/include/configs/pxm2.h @@ -21,7 +21,7 @@ #include "siemens-am33x-common.h" #define CONFIG_SYS_MPUCLK 720 -#define DXR2_IOCTRL_VAL 0x18b +#define DDR_IOCTRL_VAL 0x18b #define DDR_PLL_FREQ 266 #define BOARD_DFU_BUTTON_GPIO 59 diff --git a/include/configs/qemu-ppce500.h b/include/configs/qemu-ppce500.h index 10e014d33c..763a47ac3d 100644 --- a/include/configs/qemu-ppce500.h +++ b/include/configs/qemu-ppce500.h @@ -19,6 +19,7 @@ #undef CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_TEXT_BASE 0xf01000 /* 15 MB */ +#define CONFIG_SYS_GENERIC_BOARD #define CONFIG_SYS_MPC85XX_NO_RESETVEC diff --git a/include/configs/s5p_goni.h b/include/configs/s5p_goni.h index 991c43e1cc..799d4fe9d8 100644 --- a/include/configs/s5p_goni.h +++ b/include/configs/s5p_goni.h @@ -214,8 +214,8 @@ /* * I2C Settings */ -#define CONFIG_SOFT_I2C_GPIO_SCL s5pc110_gpio_get(j4, 3) -#define CONFIG_SOFT_I2C_GPIO_SDA s5pc110_gpio_get(j4, 0) +#define CONFIG_SOFT_I2C_GPIO_SCL S5PC110_GPIO_J43 +#define CONFIG_SOFT_I2C_GPIO_SDA S5PC110_GPIO_J40 #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ diff --git a/include/configs/s5pc210_universal.h b/include/configs/s5pc210_universal.h index 2da887109d..eb046cdac9 100644 --- a/include/configs/s5pc210_universal.h +++ b/include/configs/s5pc210_universal.h @@ -111,12 +111,9 @@ "onenand write 0x41008000 0xc00000 0x500000\0" \ "bootk=" \ "run loaduimage; bootm 0x40007FC0\0" \ - "updatemmc=" \ - "mmc boot 0 1 1 1; mmc write 0 0x42008000 0 0x200;" \ - "mmc boot 0 1 1 0\0" \ "updatebackup=" \ - "mmc boot 0 1 1 2; mmc write 0 0x42100000 0 0x200;" \ - "mmc boot 0 1 1 0\0" \ + "mmc dev 0 2; mmc write 0 0x42100000 0 0x200;" \ + "mmc dev 0 0\0" \ "updatebootb=" \ "mmc read 0 0x42100000 0x80 0x200; run updatebackup\0" \ "lpj=lpj=3981312\0" \ @@ -170,8 +167,8 @@ /* * I2C Settings */ -#define CONFIG_SOFT_I2C_GPIO_SCL exynos4_gpio_get(1, b, 7) -#define CONFIG_SOFT_I2C_GPIO_SDA exynos4_gpio_get(1, b, 6) +#define CONFIG_SOFT_I2C_GPIO_SCL EXYNOS4_GPIO_B7 +#define CONFIG_SOFT_I2C_GPIO_SDA EXYNOS4_GPIO_B6 #define CONFIG_CMD_I2C @@ -196,10 +193,10 @@ */ #define CONFIG_SOFT_SPI #define CONFIG_SOFT_SPI_MODE SPI_MODE_3 -#define CONFIG_SOFT_SPI_GPIO_SCLK exynos4_gpio_get(2, y3, 1) -#define CONFIG_SOFT_SPI_GPIO_MOSI exynos4_gpio_get(2, y3, 3) -#define CONFIG_SOFT_SPI_GPIO_MISO exynos4_gpio_get(2, y3, 0) -#define CONFIG_SOFT_SPI_GPIO_CS exynos4_gpio_get(2, y4, 3) +#define CONFIG_SOFT_SPI_GPIO_SCLK EXYNOS4_GPIO_Y31 +#define CONFIG_SOFT_SPI_GPIO_MOSI EXYNOS4_GPIO_Y33 +#define CONFIG_SOFT_SPI_GPIO_MISO EXYNOS4_GPIO_Y30 +#define CONFIG_SOFT_SPI_GPIO_CS EXYNOS4_GPIO_Y43 #define SPI_DELAY udelay(1) #undef SPI_INIT @@ -231,8 +228,8 @@ int universal_spi_read(void); #define KEY_PWR_INTERRUPT_REG MAX8998_REG_IRQ1 #define KEY_PWR_INTERRUPT_MASK (1 << 7) -#define KEY_VOL_UP_GPIO exynos4_gpio_get(2, x2, 0) -#define KEY_VOL_DOWN_GPIO exynos4_gpio_get(2, x2, 1) +#define KEY_VOL_UP_GPIO EXYNOS4_GPIO_X20 +#define KEY_VOL_DOWN_GPIO EXYNOS4_GPIO_X21 #endif /* __ASSEMBLY__ */ /* LCD console */ diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h index 721c4e6bad..73a123d430 100644 --- a/include/configs/siemens-am33x-common.h +++ b/include/configs/siemens-am33x-common.h @@ -358,7 +358,7 @@ #define CONFIG_COMMON_ENV_SETTINGS \ "verify=no \0" \ - "project_dir=systemone\0" \ + "project_dir=targetdir\0" \ "upgrade_available=0\0" \ "altbootcmd=run bootcmd\0" \ "bootlimit=3\0" \ @@ -402,7 +402,11 @@ "dfu_args=run bootargs_defaults;" \ "setenv bootargs ${bootargs} ;" \ "mtdparts default; " \ - "dfu 0 nand 0; \0" \ + "led dfu 1;" \ + "led stat 0;" \ + "dfu 0 nand 0;" \ + "led dfu 0;" \ + "led stat 1;\0" \ "dfu_alt_info=" DFU_ALT_INFO_NAND "\0" \ "net_args=run bootargs_defaults;" \ "mtdparts default;" \ diff --git a/include/configs/smdk5250.h b/include/configs/smdk5250.h index 183aae726d..66fa1799e7 100644 --- a/include/configs/smdk5250.h +++ b/include/configs/smdk5250.h @@ -14,4 +14,8 @@ #undef CONFIG_DEFAULT_DEVICE_TREE #define CONFIG_DEFAULT_DEVICE_TREE exynos5250-smdk5250 +/* Enable FIT support and comparison */ +#define CONFIG_FIT +#define CONFIG_FIT_BEST_MATCH + #endif /* __CONFIG_SMDK_H */ diff --git a/include/configs/smdk5420.h b/include/configs/smdk5420.h index b96eea8890..58f706a3a7 100644 --- a/include/configs/smdk5420.h +++ b/include/configs/smdk5420.h @@ -51,4 +51,8 @@ #define CONFIG_MAX_I2C_NUM 11 +/* Enable FIT support and comparison */ +#define CONFIG_FIT +#define CONFIG_FIT_BEST_MATCH + #endif /* __CONFIG_5420_H */ diff --git a/include/configs/smdkv310.h b/include/configs/smdkv310.h index 1388f49986..34adfaf608 100644 --- a/include/configs/smdkv310.h +++ b/include/configs/smdkv310.h @@ -12,6 +12,7 @@ /* High Level Configuration Options */ #define CONFIG_SAMSUNG 1 /* in a SAMSUNG core */ #define CONFIG_S5P 1 /* S5P Family */ +#define CONFIG_EXYNOS4 /* EXYNOS4 Family */ #define CONFIG_EXYNOS4210 1 /* which is a EXYNOS4210 SoC */ #define CONFIG_SMDKV310 1 /* working with SMDKV310*/ diff --git a/include/configs/snow.h b/include/configs/snow.h index ed5c0b614f..673fa1469b 100644 --- a/include/configs/snow.h +++ b/include/configs/snow.h @@ -14,4 +14,8 @@ #undef CONFIG_DEFAULT_DEVICE_TREE #define CONFIG_DEFAULT_DEVICE_TREE exynos5250-snow +/* Enable FIT support and comparison */ +#define CONFIG_FIT +#define CONFIG_FIT_BEST_MATCH + #endif /* __CONFIG_SNOW_H */ diff --git a/include/configs/t4qds.h b/include/configs/t4qds.h index 36bc5294ef..75609b9f61 100644 --- a/include/configs/t4qds.h +++ b/include/configs/t4qds.h @@ -10,6 +10,8 @@ #ifndef __T4QDS_H #define __T4QDS_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO #define CONFIG_CMD_REGINFO /* High Level Configuration Options */ diff --git a/include/configs/tegra-common.h b/include/configs/tegra-common.h index ae786cfd7a..129acf2cbf 100644 --- a/include/configs/tegra-common.h +++ b/include/configs/tegra-common.h @@ -48,6 +48,13 @@ #define CONFIG_SYS_NS16550_CLK V_NS16550_CLK /* + * Common HW configuration. + * If this varies between SoCs later, move to tegraNN-common.h + * Note: This is number of devices, not max device ID. + */ +#define CONFIG_SYS_MMC_MAX_DEVICE 4 + +/* * select serial console configuration */ #define CONFIG_CONS_INDEX 1 diff --git a/include/configs/trats.h b/include/configs/trats.h index c4afecf3da..90f19626a3 100644 --- a/include/configs/trats.h +++ b/include/configs/trats.h @@ -59,7 +59,7 @@ #define CONFIG_BOOTARGS "Please use defined boot" #define CONFIG_BOOTCOMMAND "run mmcboot" -#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0" +#define CONFIG_DEFAULT_CONSOLE "console=ttySAC2,115200n8\0" #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR \ - GENERATED_GBL_DATA_SIZE) @@ -121,12 +121,9 @@ "bootm 0x40007FC0 - ${fdtaddr};" \ "fi;" \ "bootm 0x40007FC0;\0" \ - "updatemmc=" \ - "mmc boot 0 1 1 1; mmc write 0 0x42008000 0 0x200;" \ - "mmc boot 0 1 1 0\0" \ "updatebackup=" \ - "mmc boot 0 1 1 2; mmc write 0 0x42100000 0 0x200;" \ - "mmc boot 0 1 1 0\0" \ + "mmc dev 0 2; mmc write 0 0x42100000 0 0x200;" \ + "mmc dev 0 0\0" \ "updatebootb=" \ "mmc read 0 0x42100000 0x80 0x200; run updatebackup\0" \ "lpj=lpj=3981312\0" \ @@ -207,8 +204,8 @@ #define CONFIG_SYS_I2C_INIT_BOARD /* I2C FG */ -#define CONFIG_SOFT_I2C_GPIO_SCL exynos4_gpio_get(2, y4, 1) -#define CONFIG_SOFT_I2C_GPIO_SDA exynos4_gpio_get(2, y4, 0) +#define CONFIG_SOFT_I2C_GPIO_SCL EXYNOS4_GPIO_Y41 +#define CONFIG_SOFT_I2C_GPIO_SDA EXYNOS4_GPIO_Y40 /* POWER */ #define CONFIG_POWER @@ -245,8 +242,8 @@ #define KEY_PWR_INTERRUPT_REG MAX8997_REG_INT1 #define KEY_PWR_INTERRUPT_MASK (1 << 0) -#define KEY_VOL_UP_GPIO exynos4_gpio_get(2, x2, 0) -#define KEY_VOL_DOWN_GPIO exynos4_gpio_get(2, x2, 1) +#define KEY_VOL_UP_GPIO EXYNOS4_GPIO_X20 +#define KEY_VOL_DOWN_GPIO EXYNOS4_GPIO_X21 #endif /* __ASSEMBLY__ */ /* LCD console */ diff --git a/include/configs/trats2.h b/include/configs/trats2.h index 14def7d16e..206975bcae 100644 --- a/include/configs/trats2.h +++ b/include/configs/trats2.h @@ -52,7 +52,7 @@ #define CONFIG_BOOTARGS "Please use defined boot" #define CONFIG_BOOTCOMMAND "run mmcboot" -#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0" +#define CONFIG_DEFAULT_CONSOLE "console=ttySAC2,115200n8\0" #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR \ - GENERATED_GBL_DATA_SIZE) @@ -111,16 +111,11 @@ "bootm 0x40007FC0 - ${fdtaddr};" \ "fi;" \ "bootm 0x40007FC0;\0" \ - "updatemmc=" \ - "mmc boot 0 1 1 1; mmc write 0x42008000 0 0x200;" \ - "mmc boot 0 1 1 0\0" \ "updatebackup=" \ - "mmc boot 0 1 1 2; mmc write 0x42100000 0 0x200;" \ - " mmc boot 0 1 1 0\0" \ + "mmc dev 0 2; mmc write 0x51000000 0 0x800;" \ + " mmc dev 0 0\0" \ "updatebootb=" \ - "mmc read 0x51000000 0x80 0x200; run updatebackup\0" \ - "updateuboot=" \ - "mmc write 0x50000000 0x80 0x400\0" \ + "mmc read 0x51000000 0x80 0x800; run updatebackup\0" \ "mmcboot=" \ "setenv bootargs root=/dev/mmcblk${mmcdev}p${mmcrootpart} " \ "${lpj} rootwait ${console} ${meminfo} ${opts} ${lcdinfo}; " \ @@ -227,8 +222,8 @@ int get_soft_i2c_sda_pin(void); #define KEY_PWR_INTERRUPT_REG MAX77686_REG_PMIC_INT1 #define KEY_PWR_INTERRUPT_MASK (1 << 1) -#define KEY_VOL_UP_GPIO exynos4x12_gpio_get(2, x2, 2) -#define KEY_VOL_DOWN_GPIO exynos4x12_gpio_get(2, x3, 3) +#define KEY_VOL_UP_GPIO EXYNOS4X12_GPIO_X22 +#define KEY_VOL_DOWN_GPIO EXYNOS4X12_GPIO_X33 #endif /* __ASSEMBLY__ */ /* LCD console */ diff --git a/include/configs/tseries.h b/include/configs/tseries.h index 8fb87ac441..e550afad4f 100644 --- a/include/configs/tseries.h +++ b/include/configs/tseries.h @@ -237,7 +237,7 @@ #elif defined(CONFIG_EMMC_BOOT) #undef CONFIG_ENV_IS_NOWHERE #define CONFIG_ENV_IS_IN_MMC -#define CONFIG_SYS_MMC_ENV_DEV 1 +#define CONFIG_SYS_MMC_ENV_DEV 0 #define CONFIG_SYS_MMC_ENV_PART 2 #define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */ #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) diff --git a/include/configs/udoo.h b/include/configs/udoo.h index a0306de6a3..700e9c1b23 100644 --- a/include/configs/udoo.h +++ b/include/configs/udoo.h @@ -26,6 +26,8 @@ #define CONFIG_INITRD_TAG #define CONFIG_REVISION_TAG +#define CONFIG_SYS_GENERIC_BOARD + /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (2 * SZ_1M) diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h index 6c74c72952..7d96908f0e 100644 --- a/include/configs/wandboard.h +++ b/include/configs/wandboard.h @@ -26,6 +26,8 @@ #define CONFIG_INITRD_TAG #define CONFIG_REVISION_TAG +#define CONFIG_SYS_GENERIC_BOARD + /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) @@ -56,6 +58,12 @@ #define CONFIG_LOADADDR 0x12000000 #define CONFIG_SYS_TEXT_BASE 0x17800000 +/* I2C Configs */ +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_SPEED 100000 + /* MMC Configuration */ #define CONFIG_FSL_ESDHC #define CONFIG_FSL_USDHC @@ -98,7 +106,9 @@ #define CONFIG_VIDEO_LOGO #define CONFIG_VIDEO_BMP_LOGO #define CONFIG_IPUV3_CLK 260000000 +#define CONFIG_CMD_HDMIDETECT #define CONFIG_IMX_HDMI +#define CONFIG_IMX_VIDEO_SKIP #if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S) #define CONFIG_DEFAULT_FDT_FILE "imx6dl-wandboard.dtb" @@ -135,7 +145,33 @@ "fi; " \ "fi\0" \ "mmcargs=setenv bootargs console=${console},${baudrate} " \ - "root=${mmcroot}\0" \ + "root=${mmcroot}; run videoargs\0" \ + "videoargs=" \ + "setenv nextcon 0; " \ + "if hdmidet; then " \ + "setenv bootargs ${bootargs} " \ + "video=mxcfb${nextcon}:dev=hdmi,1280x720M@60," \ + "if=RGB24; " \ + "setenv fbmen fbmem=28M; " \ + "setexpr nextcon ${nextcon} + 1; " \ + "else " \ + "echo - no HDMI monitor;" \ + "fi; " \ + "i2c dev 1; " \ + "if i2c probe 0x10; then " \ + "setenv bootargs ${bootargs} " \ + "video=mxcfb${nextcon}:dev=lcd,800x480@60," \ + "if=RGB666; " \ + "if test 0 -eq ${nextcon}; then " \ + "setenv fbmem fbmem=10M; " \ + "else " \ + "setenv fbmem ${fbmem},10M; " \ + "fi; " \ + "setexpr nextcon ${nextcon} + 1; " \ + "else " \ + "echo '- no FWBADAPT-7WVGA-LCD-F07A-0102 display';" \ + "fi; " \ + "setenv bootargs ${bootargs} ${fbmem}\0" \ "loadbootscript=" \ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ "bootscript=echo Running bootscript from mmc ...; " \ diff --git a/include/configs/x600.h b/include/configs/x600.h index 7405419f0e..eae85d62c9 100644 --- a/include/configs/x600.h +++ b/include/configs/x600.h @@ -107,6 +107,7 @@ #define CONFIG_CMD_DHCP #define CONFIG_CMD_ENV #define CONFIG_CMD_FPGA +#define CONFIG_CMD_FPGA_LOADMK #define CONFIG_CMD_GPIO #define CONFIG_CMD_I2C #define CONFIG_CMD_MEMORY diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h index 579091d605..dc5bc22ce9 100644 --- a/include/configs/zynq-common.h +++ b/include/configs/zynq-common.h @@ -214,6 +214,10 @@ #define CONFIG_FPGA_XILINX #define CONFIG_FPGA_ZYNQPL #define CONFIG_CMD_FPGA +#define CONFIG_CMD_FPGA_LOADMK +#define CONFIG_CMD_FPGA_LOADP +#define CONFIG_CMD_FPGA_LOADBP +#define CONFIG_CMD_FPGA_LOADFS /* Open Firmware flat tree */ #define CONFIG_OF_LIBFDT diff --git a/include/dfu.h b/include/dfu.h index 240916854a..26ffbc8e81 100644 --- a/include/dfu.h +++ b/include/dfu.h @@ -43,6 +43,9 @@ struct mmc_internal_data { unsigned int lba_size; unsigned int lba_blk_size; + /* eMMC HW partition access */ + int hw_partition; + /* FAT/EXT */ unsigned int dev; unsigned int part; @@ -100,6 +103,7 @@ struct dfu_entity { u64 offset, void *buf, long *len); int (*flush_medium)(struct dfu_entity *dfu); + unsigned int (*poll_timeout)(struct dfu_entity *dfu); struct list_head list; diff --git a/include/fpga.h b/include/fpga.h index 15e603a169..914024c17c 100644 --- a/include/fpga.h +++ b/include/fpga.h @@ -35,13 +35,29 @@ typedef struct { /* typedef fpga_desc */ void *devdesc; /* real device descriptor */ } fpga_desc; /* end, typedef fpga_desc */ +typedef struct { /* typedef fpga_desc */ + unsigned int blocksize; + char *interface; + char *dev_part; + char *filename; + int fstype; +} fpga_fs_info; + +typedef enum { + BIT_FULL = 0, + BIT_PARTIAL, +} bitstream_type; /* root function definitions */ extern void fpga_init(void); extern int fpga_add(fpga_type devtype, void *desc); extern int fpga_count(void); -extern int fpga_load(int devnum, const void *buf, size_t bsize); -extern int fpga_loadbitstream(int devnum, char *fpgadata, size_t size); +extern int fpga_load(int devnum, const void *buf, size_t bsize, + bitstream_type bstype); +extern int fpga_fsload(int devnum, const void *buf, size_t size, + fpga_fs_info *fpga_fsinfo); +extern int fpga_loadbitstream(int devnum, char *fpgadata, size_t size, + bitstream_type bstype); extern int fpga_dump(int devnum, const void *buf, size_t bsize); extern int fpga_info(int devnum); extern const fpga_desc *const fpga_validate(int devnum, const void *buf, diff --git a/include/image.h b/include/image.h index b27877870b..18861686cc 100644 --- a/include/image.h +++ b/include/image.h @@ -413,6 +413,7 @@ enum fit_load_op { #define IMAGE_FORMAT_INVALID 0x00 #define IMAGE_FORMAT_LEGACY 0x01 /* legacy image_header based format */ #define IMAGE_FORMAT_FIT 0x02 /* new, libfdt based format */ +#define IMAGE_FORMAT_ANDROID 0x03 /* Android boot image */ int genimg_get_format(const void *img_addr); int genimg_has_config(bootm_headers_t *images); @@ -1031,4 +1032,16 @@ static inline int fit_image_check_target_arch(const void *fdt, int node) #endif /* CONFIG_FIT_VERBOSE */ #endif /* CONFIG_FIT */ +#if defined(CONFIG_ANDROID_BOOT_IMAGE) +struct andr_img_hdr; +int android_image_check_header(const struct andr_img_hdr *hdr); +int android_image_get_kernel(const struct andr_img_hdr *hdr, int verify, + ulong *os_data, ulong *os_len); +int android_image_get_ramdisk(const struct andr_img_hdr *hdr, + ulong *rd_data, ulong *rd_len); +ulong android_image_get_end(const struct andr_img_hdr *hdr); +ulong android_image_get_kload(const struct andr_img_hdr *hdr); + +#endif /* CONFIG_ANDROID_BOOT_IMAGE */ + #endif /* __IMAGE_H__ */ diff --git a/include/mmc.h b/include/mmc.h index bc11f45a6f..a3a100bd39 100644 --- a/include/mmc.h +++ b/include/mmc.h @@ -54,6 +54,7 @@ #define COMM_ERR -18 /* Communications Error */ #define TIMEOUT -19 #define IN_PROGRESS -20 /* operation is in progress */ +#define SWITCH_ERR -21 /* Card reports failure to switch mode */ #define MMC_CMD_GO_IDLE_STATE 0 #define MMC_CMD_SEND_OP_COND 1 @@ -70,6 +71,7 @@ #define MMC_CMD_SET_BLOCKLEN 16 #define MMC_CMD_READ_SINGLE_BLOCK 17 #define MMC_CMD_READ_MULTIPLE_BLOCK 18 +#define MMC_CMD_SET_BLOCK_COUNT 23 #define MMC_CMD_WRITE_SINGLE_BLOCK 24 #define MMC_CMD_WRITE_MULTIPLE_BLOCK 25 #define MMC_CMD_ERASE_GROUP_START 35 @@ -109,6 +111,7 @@ #define SECURE_ERASE 0x80000000 #define MMC_STATUS_MASK (~0x0206BF7F) +#define MMC_STATUS_SWITCH_ERROR (1 << 7) #define MMC_STATUS_RDY_FOR_DATA (1 << 8) #define MMC_STATUS_CURR_STATE (0xf << 9) #define MMC_STATUS_ERROR (1 << 19) @@ -225,6 +228,7 @@ * boot partitions (2), general purpose partitions (4) in MMC v4.4. */ #define MMC_NUM_BOOT_PARTITION 2 +#define MMC_PART_RPMB 3 /* RPMB partition number */ struct mmc_cid { unsigned long psn; @@ -336,7 +340,13 @@ int mmc_set_part_conf(struct mmc *mmc, u8 ack, u8 part_num, u8 access); int mmc_set_boot_bus_width(struct mmc *mmc, u8 width, u8 reset, u8 mode); /* Function to modify the RST_n_FUNCTION field of EXT_CSD */ int mmc_set_rst_n_function(struct mmc *mmc, u8 enable); - +/* Functions to read / write the RPMB partition */ +int mmc_rpmb_set_key(struct mmc *mmc, void *key); +int mmc_rpmb_get_counter(struct mmc *mmc, unsigned long *counter); +int mmc_rpmb_read(struct mmc *mmc, void *addr, unsigned short blk, + unsigned short cnt, unsigned char *key); +int mmc_rpmb_write(struct mmc *mmc, void *addr, unsigned short blk, + unsigned short cnt, unsigned char *key); /** * Start device initialization and return immediately; it does not block on * polling OCR (operation condition register) status. Then you should call diff --git a/include/palmas.h b/include/palmas.h index eaf367086c..cca3f9a9d1 100644 --- a/include/palmas.h +++ b/include/palmas.h @@ -24,6 +24,10 @@ #define LDO1_CTRL 0x50 #define LDO1_VOLTAGE 0x51 +/* LDO2 control/voltage */ +#define LDO2_CTRL 0x52 +#define LDO2_VOLTAGE 0x53 + /* LDO9 control/voltage */ #define LDO9_CTRL 0x60 #define LDO9_VOLTAGE 0x61 diff --git a/include/part.h b/include/part.h index 53532dcd61..f2c8c641fa 100644 --- a/include/part.h +++ b/include/part.h @@ -103,6 +103,7 @@ block_dev_desc_t* sata_get_dev(int dev); block_dev_desc_t* scsi_get_dev(int dev); block_dev_desc_t* usb_stor_get_dev(int dev); block_dev_desc_t* mmc_get_dev(int dev); +int mmc_select_hwpart(int dev_num, int hwpart); block_dev_desc_t* systemace_get_dev(int dev); block_dev_desc_t* mg_disk_get_dev(int dev); block_dev_desc_t *host_get_dev(int dev); @@ -126,6 +127,7 @@ static inline block_dev_desc_t* sata_get_dev(int dev) { return NULL; } static inline block_dev_desc_t* scsi_get_dev(int dev) { return NULL; } static inline block_dev_desc_t* usb_stor_get_dev(int dev) { return NULL; } static inline block_dev_desc_t* mmc_get_dev(int dev) { return NULL; } +static inline int mmc_select_hwpart(int dev_num, int hwpart) { return -1; } static inline block_dev_desc_t* systemace_get_dev(int dev) { return NULL; } static inline block_dev_desc_t* mg_disk_get_dev(int dev) { return NULL; } static inline block_dev_desc_t *host_get_dev(int dev) { return NULL; } diff --git a/include/power/ltc3676_pmic.h b/include/power/ltc3676_pmic.h new file mode 100644 index 0000000000..dcaa985193 --- /dev/null +++ b/include/power/ltc3676_pmic.h @@ -0,0 +1,51 @@ +/* + * Copyright (C) 2014 Gateworks Corporation + * Tim Harvey <tharvey@gateworks.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __LTC3676_PMIC_H_ +#define __LTC3676_PMIC_H_ + +/* LTC3676 registers */ +enum { + LTC3676_BUCK1 = 0x01, + LTC3676_BUCK2 = 0x02, + LTC3676_BUCK3 = 0x03, + LTC3676_BUCK4 = 0x04, + LTC3676_LDOA = 0x05, + LTC3676_LDOB = 0x06, + LTC3676_SQD1 = 0x07, + LTC3676_SQD2 = 0x08, + LTC3676_CNTRL = 0x09, + LTC3676_DVB1A = 0x0A, + LTC3676_DVB1B = 0x0B, + LTC3676_DVB2A = 0x0C, + LTC3676_DVB2B = 0x0D, + LTC3676_DVB3A = 0x0E, + LTC3676_DVB3B = 0x0F, + LTC3676_DVB4A = 0x10, + LTC3676_DVB4B = 0x11, + LTC3676_MSKIRQ = 0x12, + LTC3676_MSKPG = 0x13, + LTC3676_USER = 0x14, + LTC3676_HRST = 0x1E, + LTC3676_CLIRQ = 0x1F, + LTC3676_IRQSTAT = 0x15, + LTC3676_PGSTATL = 0x16, + LTC3676_PGSTATR = 0x17, + LTC3676_NUM_OF_REGS = 0x20, +}; + +/* + * SW Configuration + */ + +#define LTC3676_DVB_MASK 0x1f +#define LTC3676_PGOOD_MASK (1<<5) +#define LTC3676_REF_SELA (0<<5) +#define LTC3676_REF_SELB (1<<5) + +int power_ltc3676_init(unsigned char bus); +#endif diff --git a/include/power/pfuze100_pmic.h b/include/power/pfuze100_pmic.h index 2a9032a1f9..444aba6c66 100644 --- a/include/power/pfuze100_pmic.h +++ b/include/power/pfuze100_pmic.h @@ -93,4 +93,5 @@ enum { #define SWBST_MODE_AUTO (2 << 2) #define SWBST_MODE_APS (2 << 3) +int power_pfuze100_init(unsigned char bus); #endif diff --git a/include/samsung/misc.h b/include/samsung/misc.h index ede6c1583a..10653a1b17 100644 --- a/include/samsung/misc.h +++ b/include/samsung/misc.h @@ -15,6 +15,8 @@ enum { BOOT_MODE_THOR, BOOT_MODE_UMS, BOOT_MODE_DFU, + BOOT_MODE_GPT, + BOOT_MODE_ENV, BOOT_MODE_EXIT, }; diff --git a/include/usb/ehci-fsl.h b/include/usb/ehci-fsl.h index c9ee1d5bf6..dd77ad6325 100644 --- a/include/usb/ehci-fsl.h +++ b/include/usb/ehci-fsl.h @@ -11,6 +11,8 @@ #include <asm/processor.h> +#define CONTROL_REGISTER_W1C_MASK 0x00020000 /* W1C: PHY_CLK_VALID */ + /* Global offsets */ #define FSL_SKIP_PCI 0x100 diff --git a/include/usb_mass_storage.h b/include/usb_mass_storage.h index ed460644c1..69b80cd1a3 100644 --- a/include/usb_mass_storage.h +++ b/include/usb_mass_storage.h @@ -9,17 +9,9 @@ #define __USB_MASS_STORAGE_H__ #define SECTOR_SIZE 0x200 -#include <mmc.h> +#include <part.h> #include <linux/usb/composite.h> -#ifndef UMS_START_SECTOR -#define UMS_START_SECTOR 0 -#endif - -#ifndef UMS_NUM_SECTORS -#define UMS_NUM_SECTORS 0 -#endif - /* Wait at maximum 60 seconds for cable connection */ #define UMS_CABLE_READY_TIMEOUT 60 @@ -31,14 +23,13 @@ struct ums { unsigned int start_sector; unsigned int num_sectors; const char *name; - struct mmc *mmc; + block_dev_desc_t *block_dev; }; extern struct ums *ums; int fsg_init(struct ums *); void fsg_cleanup(void); -struct ums *ums_init(unsigned int); int fsg_main_thread(void *); int fsg_add(struct usb_configuration *c); #endif /* __USB_MASS_STORAGE_H__ */ diff --git a/include/xilinx.h b/include/xilinx.h index 9801267c59..aebcb3bfdf 100644 --- a/include/xilinx.h +++ b/include/xilinx.h @@ -45,16 +45,20 @@ typedef struct { /* typedef xilinx_desc */ } xilinx_desc; /* end, typedef xilinx_desc */ struct xilinx_fpga_op { - int (*load)(xilinx_desc *, const void *, size_t); + int (*load)(xilinx_desc *, const void *, size_t, bitstream_type); + int (*loadfs)(xilinx_desc *, const void *, size_t, fpga_fs_info *); int (*dump)(xilinx_desc *, const void *, size_t); int (*info)(xilinx_desc *); }; /* Generic Xilinx Functions *********************************************************************/ -int xilinx_load(xilinx_desc *desc, const void *image, size_t size); +int xilinx_load(xilinx_desc *desc, const void *image, size_t size, + bitstream_type bstype); int xilinx_dump(xilinx_desc *desc, const void *buf, size_t bsize); int xilinx_info(xilinx_desc *desc); +int xilinx_loadfs(xilinx_desc *desc, const void *buf, size_t bsize, + fpga_fs_info *fpga_fsinfo); /* Board specific implementation specific function types *********************************************************************/ diff --git a/lib/Makefile b/lib/Makefile index 27e4f78bfd..377ab134ba 100644 --- a/lib/Makefile +++ b/lib/Makefile @@ -35,6 +35,7 @@ obj-y += net_utils.o obj-$(CONFIG_PHYSMEM) += physmem.o obj-y += qsort.o obj-$(CONFIG_SHA1) += sha1.o +obj-$(CONFIG_SUPPORT_EMMC_RPMB) += sha256.o obj-$(CONFIG_SHA256) += sha256.o obj-y += strmhz.o obj-$(CONFIG_TPM) += tpm.o diff --git a/nand_spl/board/freescale/p1_p2_rdb/Makefile b/nand_spl/board/freescale/p1_p2_rdb/Makefile deleted file mode 100644 index 9f338024ea..0000000000 --- a/nand_spl/board/freescale/p1_p2_rdb/Makefile +++ /dev/null @@ -1,91 +0,0 @@ -# -# (C) Copyright 2007 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# -# Copyright 2009-2011 Freescale Semiconductor, Inc. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -CONFIG_SYS_TEXT_BASE_SPL := 0xfff00000 -PAD_TO := 0xfff01000 - -nandobj := $(objtree)/nand_spl/ - -LDSCRIPT= $(srctree)/$(CPUDIR)/u-boot-nand_spl.lds -LDFLAGS := -T $(nandobj)u-boot-nand_spl.lds -Ttext $(CONFIG_SYS_TEXT_BASE_SPL) \ - $(LDFLAGS) $(LDFLAGS_FINAL) -asflags-y += -DCONFIG_NAND_SPL -ccflags-y += -DCONFIG_NAND_SPL - -SOBJS = start.o resetvec.o -COBJS = cache.o cpu_init_early.o spl_minimal.o fsl_law.o law.o \ - nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o - -OBJS := $(addprefix $(obj)/,$(SOBJS) $(COBJS)) -__OBJS := $(SOBJS) $(COBJS) -LNDIR := $(nandobj)board/$(BOARDDIR) - -targets += $(__OBJS) - -all: $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin - -$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) --pad-to=$(PAD_TO) -O binary $< $@ - -$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) -O binary $< $@ - -$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot-nand_spl.lds - cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \ - -Map $(nandobj)u-boot-spl.map -o $@ - -$(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT) - $(CPP) $(cpp_flags) $(LDPPFLAGS) -I$(nandobj)/board/$(BOARDDIR) \ - -ansi -D__ASSEMBLY__ -P - <$< >$@ - -# create symbolic links for common files - -$(obj)/cache.c: - @rm -f $@ - ln -sf $(srctree)/arch/powerpc/lib/cache.c $@ - -$(obj)/cpu_init_early.c: - @rm -f $@ - ln -sf $(srctree)/arch/powerpc/cpu/mpc85xx/cpu_init_early.c $@ - -$(obj)/spl_minimal.c: - @rm -f $@ - ln -sf $(srctree)/arch/powerpc/cpu/mpc85xx/spl_minimal.c $@ - -$(obj)/fsl_law.c: - @rm -f $@ - ln -sf $(srctree)/arch/powerpc/cpu/mpc8xxx/law.c $@ - -$(obj)/law.c: - @rm -f $@ - ln -sf $(srctree)/board/$(BOARDDIR)/law.c $@ - -$(obj)/nand_boot_fsl_elbc.c: - @rm -f $@ - ln -sf $(srctree)/nand_spl/nand_boot_fsl_elbc.c $@ - -$(obj)/ns16550.c: - @rm -f $@ - ln -sf $(srctree)/drivers/serial/ns16550.c $@ - -$(obj)/resetvec.S: - @rm -f $@ - ln -s $(srctree)/$(CPUDIR)/resetvec.S $@ - -$(obj)/start.S: - @rm -f $@ - ln -sf $(srctree)/arch/powerpc/cpu/mpc85xx/start.S $@ - -$(obj)/tlb.c: - @rm -f $@ - ln -sf $(srctree)/arch/powerpc/cpu/mpc85xx/tlb.c $@ - -$(obj)/tlb_table.c: - @rm -f $@ - ln -sf $(srctree)/board/$(BOARDDIR)/tlb.c $@ diff --git a/nand_spl/board/freescale/p1_p2_rdb/nand_boot.c b/nand_spl/board/freescale/p1_p2_rdb/nand_boot.c deleted file mode 100644 index f7e8438438..0000000000 --- a/nand_spl/board/freescale/p1_p2_rdb/nand_boot.c +++ /dev/null @@ -1,82 +0,0 @@ -/* - * Copyright 2009 Freescale Semiconductor, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include <common.h> -#include <mpc85xx.h> -#include <asm/io.h> -#include <ns16550.h> -#include <nand.h> -#include <asm/mmu.h> -#include <asm/immap_85xx.h> -#include <fsl_ddr_sdram.h> -#include <asm/fsl_law.h> - -#define SYSCLK_MASK 0x00200000 -#define BOARDREV_MASK 0x10100000 -#define BOARDREV_B 0x10100000 -#define BOARDREV_C 0x00100000 - -#define SYSCLK_66 66666666 -#define SYSCLK_50 50000000 -#define SYSCLK_100 100000000 - -DECLARE_GLOBAL_DATA_PTR; - -void board_init_f(ulong bootflag) -{ - uint plat_ratio, bus_clk, sys_clk = 0; - volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - volatile ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR); - uint val, temp, sysclk_mask; - - val = pgpio->gpdat; - sysclk_mask = val & SYSCLK_MASK; - temp = val & BOARDREV_MASK; - if (temp == BOARDREV_C) { - if(sysclk_mask == 0) - sys_clk = SYSCLK_66; - else - sys_clk = SYSCLK_100; - } else if (temp == BOARDREV_B) { - if(sysclk_mask == 0) - sys_clk = SYSCLK_66; - else - sys_clk = SYSCLK_50; - } - - plat_ratio = gur->porpllsr & 0x0000003e; - plat_ratio >>= 1; - bus_clk = plat_ratio * sys_clk; - NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, - bus_clk / 16 / CONFIG_BAUDRATE); - - puts("\nNAND boot... "); - - /* copy code to DDR and jump to it - this should not return */ - /* NOTE - code has to be copied out of NAND buffer before - * other blocks can be read. - */ - relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, 0, - CONFIG_SYS_NAND_U_BOOT_RELOC); -} - -void board_init_r(gd_t *gd, ulong dest_addr) -{ - nand_boot(); -} - -void putc(char c) -{ - if (c == '\n') - NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r'); - - NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c); -} - -void puts(const char *str) -{ - while (*str) - putc(*str++); -} diff --git a/tools/patman/patchstream.py b/tools/patman/patchstream.py index 9f5682cd0f..3228719207 100644 --- a/tools/patman/patchstream.py +++ b/tools/patman/patchstream.py @@ -275,7 +275,8 @@ class PatchStream: # Suppress duplicate signoffs elif signoff_match: - if self.commit.CheckDuplicateSignoff(signoff_match.group(1)): + if (self.is_log or + self.commit.CheckDuplicateSignoff(signoff_match.group(1))): out = [line] # Well that means this is an ordinary line |
