diff options
32 files changed, 917 insertions, 197 deletions
@@ -1,3 +1,687 @@ +commit 467bcee11fe26ad422f2de971aa70866079870f2 +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Fri Dec 14 15:36:18 2007 +0100 + + cfi_flash: Add manufacturer-specific fixups + + Run fixups based on the JEDEC manufacturer ID independent of the + command set ID. + + This changes current behaviour: Previously, geometry reversal for AMD + chips were done based on the command set ID, while they are now done + based on the JEDEC manufacturer and device ID. + + Also add fixup for top-boot Atmel chips. A fixup is needed for + AT49BV6416(T) too, but since u-boot currently only reads the low byte + of the device ID, there's no way to tell it apart from AT49BV642D, + which should not have this fixup. Since AT49BV642D support is + necessary to get ATNGW100 board support into mainline, I've commented + out the fixup for now. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 0ddf06ddf6b4bd057ad4c5f0dffea7870ba06a2a +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Fri Dec 14 15:36:17 2007 +0100 + + cfi_flash: Add cmdset-specific init functions + + Move things like reading JEDEC IDs and fixing up geometry reversal + into separate functions. The geometry reversal fixup is now performed + by altering the qry structure directly, which makes the sector init + code slightly cleaner. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit e23741f4a6d8047520ef0d4971762749b3587d32 +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Fri Dec 14 15:36:16 2007 +0100 + + cfi_flash: Read whole QRY structure in one go + + Read out the whole CFI Standard Query structure after successful cfi + identification. This allows subsequent code to access this information + directly without having to go through flash_read_uchar() and friends. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit df9c25ea04b38a0e05d4f8c73c5cc144cdafa7db +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Mon Dec 17 11:02:44 2007 +0100 + + AVR32: Fix logic inversion in disable_interrupts() + + disable_interrupts() should return nonzero if interrupts were + _enabled_ before, not disabled. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit acac475212cbedb17b321a363a1c878e2b47b37f +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Fri Dec 14 16:51:22 2007 +0100 + + AVR32: Enable interrupts at bootup + + The timer code depends on the timer interrupt to keep track of the + upper 32 bits of the cycle counter. This obviously doesn't work when + interrupts are disabled the whole time. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 9570bcd87f4db255514f43b6701746c412f8fef0 +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Thu Nov 15 10:03:45 2007 +0100 + + AVR32: Fix wrong pin setup for USART3 + + As reported by Gerhard Berghofer: + + in "gpio_enable_usart3" the correct pins for USART 3 are PB17 and PB18 + instead of PB18 and PB19. + + which is obviously correct. There's currently no code that uses + USART3, but custom boards may run into problems. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 09ea0de03dcc3ee7af045b0b572227bda2c1c918 +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Thu Nov 1 12:44:20 2007 +0100 + + README: Remove ATSTK1000 daughterboard list + + As noted by Kim Phillips, these lists tend to become out of date. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit c81cbbad21cb0ae983e2e796211202234cdc8be2 +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Tue Oct 30 14:56:36 2007 +0100 + + Add ATSTK100[234] to MAINTAINERS + + Add all the ATSTK1000 daughterboards to MAINTAINERS along with their + "mother". Also update the entry for ATSTK1000 to be not only about the + AP7000 CPU; it's intended to handle all CPUs in the AT32AP family. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 64ff2357b1727213803591813dbc779c924bf772 +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Mon Oct 29 13:02:54 2007 +0100 + + AVR32: Add support for the ATSTK1004 board + + ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU, + which is a derivative of AT32AP7000. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 667568db157f374b85abd7e03596ddd1f0b25681 +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Mon Oct 29 13:02:54 2007 +0100 + + AVR32: Add support for the ATSTK1003 board + + ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU, + which is a derivative of AT32AP7000. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 5fee84a794a51ec830548cda485a770efb018b92 +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Mon Oct 29 13:23:33 2007 +0100 + + AVR32: Make some AT32AP700x peripherals optional + + Add a chip-features file providing definitions of the form + + AT32AP700x_CHIP_HAS_<peripheral> + + to indicate the availability of the given peripheral on the currently + selected chip. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 36f28f8a9605ee5dcfa330482cfc62171261af97 +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Mon Oct 29 13:09:56 2007 +0100 + + AVR32: Rename at32ap7000 -> at32ap700x + + The SoC-specific code for all the AT32AP700x CPUs is practically + identical; the only difference is that some chips have less features + than others. By doing this rename, we can add support for the AP7000 + derivatives simply by making some features conditional. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 4d5fa99c73f354e7cf985efcf417ea55ca2f6a5e +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Fri Jun 29 18:22:34 2007 +0200 + + atmel_mci: Show SR when block read fails + + Show controller status as well as card status when an error occurs + during block read. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 12d30aa79779c2aa7a998bbae4c075f822a53004 +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Thu Dec 13 12:56:34 2007 +0100 + + cfi_flash: Use map_physmem() and unmap_physmem() + + Use map_physmem() and unmap_physmem() to convert from physical to + virtual addresses. This gives the arch a chance to provide an uncached + mapping for flash accesses. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 4d7d6936eb29af7cca330937808312aa5f61454d +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Thu Dec 13 12:56:33 2007 +0100 + + Introduce map_physmem() and unmap_physmem() + + map_physmem() returns a virtual address which can be used to access a + given physical address without involving the cache. unmap_physmem() + should be called when the virtual address returned by map_physmem() is + no longer needed. + + This patch adds a stub implementation which simply returns the + physical address cast to a uchar * for all architectures except AVR32, + which converts the physical address to an uncached virtual mapping. + unmap_physmem() is a no-op on all architectures, but if any + architecture needs to do such mappings through the TLB, this is the + hook where those TLB entries can be invalidated. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit cdbaefb5f5f03e54455d0439dcf6dbd97ead1f9d +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Thu Dec 13 12:56:32 2007 +0100 + + cfi_flash: Introduce read and write accessors + + Introduce flash_read{8,16,32,64) and flash_write{8,16,32,64} and use + them to access the flash memory. This makes it clearer when the flash + is actually being accessed; merely dereferencing a volatile pointer + looks just like any other kind of access. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 812711ce6b3a386125dcf0d6a59588e461abbb87 +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Thu Dec 13 12:56:31 2007 +0100 + + Implement __raw_{read,write}[bwl] on all architectures + + This adds implementations of __raw_read[bwl] and __raw_write[bwl] to + m68k, ppc, nios and nios2. The m68k and ppc implementations were taken + from Linux. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit be60a9021c82fc5aecd5b2b1fc96f70a9c81bbcd +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Sat Oct 6 18:55:36 2007 +0200 + + cfi_flash: Reorder functions and eliminate extra prototypes + + Reorder the functions in cfi_flash.c so that each function only uses + functions that have been defined before it. This allows the static + prototype declarations near the top to be eliminated and might allow + gcc to do a better job inlining functions. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 3055793bcbdf24b1f8117f606ffb766d32eb766f +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Thu Dec 13 12:56:29 2007 +0100 + + cfi_flash: Make some needlessly global functions static + + Make functions not declared in any header file static. + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 7e5b9b471518c5652febc68ba62b432193d6abf4 +Author: Haavard Skinnemoen <hskinnemoen@atmel.com> +Date: Thu Dec 13 12:56:28 2007 +0100 + + cfi_flash: Break long lines + + This patch tries to keep all lines in the cfi_flash driver below 80 + columns. There are a few lines left which don't fit this requirement + because I couldn't find any trivial way to break them (i.e. it would + take some restructuring, which I intend to do in a later patch.) + + Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> + +commit 42026c9cb3a76849b41e6e24abfb7b56807a5c1a +Author: Bartlomiej Sieka <tur@semihalf.com> +Date: Tue Dec 11 13:59:57 2007 +0100 + + CFI: synchronize command offsets with Linux CFI driver + + Fixes non-working CFI Flash on the Inka4x0 board. + + Signed-off-by: Bartlomiej Sieka <tur@semihalf.com> + +commit 8ff3de61fc5f9b3b21647bce081a3b7f710f0d4d +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Fri Dec 7 12:17:34 2007 -0600 + + Handle MPC85xx PCIe reset errata (PCI-Ex 38) + + On the MPC85xx boards that have PCIe enable the PCIe errata fix. + (MPC8544DS, MPC8548CDS, MPC8568MDS). + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 82ac8c97145a4c3bf8b3dbfad00fa96e920f9b9c +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Fri Dec 7 12:04:30 2007 -0600 + + Update Freescale MPC85xx ADS/CDS/MDS board config + + * Enabled CONFIG_CMD_ELF + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit d435793229ce29a42797c1edc39f5b34f987f91a +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Fri Dec 7 04:59:26 2007 -0600 + + Handle Asynchronous DDR clock on 85xx + + The MPC8572 introduces the concept of an asynchronous DDR clock with + regards to the platform clock. + + Introduce get_ddr_freq() to report the DDR freq regardless of sync/async + mode. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 22abb2d2eaf7b795a6923c6273ec9cb53fda9a10 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Thu Nov 29 10:34:28 2007 -0600 + + Update Freescale MPC85xx ADS/CDS/MDS board config + + * Removed some misc environment setup + * Enabled CONFIG_CMDLINE_EDITING + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 415a613babb84d5e5d5b42e8e553868c71fc3a64 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Thu Nov 29 10:47:44 2007 -0600 + + Move the MPC8541/MPC8555/MPC8548 CDS board under board/freescale. + + Minor path corrections needed to ensure buildability. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit c2d943ffbfd3359b3b45d177b437379d2cb86fbf +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Thu Nov 29 10:16:18 2007 -0600 + + Move the MPC8540 ADS board under board/freescale. + + Minor path corrections needed to ensure buildability. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 870ceac5b3a3486c109396e005af81ae762b5710 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Thu Nov 29 10:14:50 2007 -0600 + + Move the MPC8560 ADS board under board/freescale. + + Minor path corrections needed to ensure buildability. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit acbca876fb3fec25cd9c55b0efc81ff618ff5262 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Thu Nov 29 10:13:47 2007 -0600 + + Move the MPC8568 MDS board under board/freescale. + + Minor path corrections needed to ensure buildability. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit a853d56c59b33415304531443633808736acfc6e +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Thu Nov 29 02:18:59 2007 -0600 + + Use standard LAWAR_TRGT_IF_* defines for LAW setup on 85xx + + We already had defines for LAWAR_TRGT_IF_* that we should use + rather than creating new ones. Also, added some missing defines for + PCIE targets. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 04db400892da37b76a585e332a0c137954ad2015 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Thu Nov 29 02:10:09 2007 -0600 + + Stop using immap_t on 85xx + + In the future the offsets to various blocks may not be in same location. + Move to using CFG_MPC85xx_*_ADDR as the base of the registers + instead of getting it via &immap. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 2714223f8e04ab3e4133ff65872eef366d90bfea +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Thu Nov 29 01:23:09 2007 -0600 + + Remove CONFIG_OF_FLAT_TREE related code from mpc85xx since we now use libfdt + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit c480861bf000156e6a3e932c258db59ff2212dd3 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Thu Nov 29 01:06:19 2007 -0600 + + Update MPC8568 MDS to use libfdt + + Updated the MPC8568 MDS config to use libfdt and assume use of aliases for + ethernet, pci, and serial for the various fixups that are done. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 1563f56e0c68f6920f956382d6d13bee3f01c0f7 +Author: Haiying Wang <Haiying.Wang@freescale.com> +Date: Wed Nov 14 15:52:06 2007 -0500 + + Add PCI Express support on MPC8568MDS + + Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit b90d25497625b90ffa3f2911a0895ca237556ff5 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Thu Nov 29 00:11:44 2007 -0600 + + Update MPC85xx CDS to use libfdt + + Updated the MPC85xx CDS config to use libfdt and assume use of aliases for + ethernet, pci, and serial for the various fixups that are done. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 0fd5ec66b10521a057ad73e69ab5f0f9eafba255 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Wed Nov 28 22:54:27 2007 -0600 + + Update MPC8540 ADS to use libfdt + + Updated the MPC8540 ADS config to use libfdt and assume use of aliases for + ethernet, pci, and serial for the various fixups that are done. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 5ce715802f6c50dc78b3405b92f184b1e3710519 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Wed Nov 28 22:40:31 2007 -0600 + + Update MPC8560 ADS to use libfdt + + Updated the MPC8560 ADS config to use libfdt and assume use of aliases for + ethernet, pci, and serial for the various fixups that are done. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit aafeefbdb8b029f5ca2a195598d0a501a606eea9 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Wed Nov 28 00:36:33 2007 -0600 + + Stop using immap_t for cpm offset on 85xx + + In the future the offsets to various blocks may not be in same location. + Move to using CFG_MPC85xx_CPM_ADDR as the base of the CPM registers + instead of getting it via &immap->im_cpm. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit f59b55a5b8fcadaa99781ba48e7a38e956afa527 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Tue Nov 27 23:25:02 2007 -0600 + + Stop using immap_t for guts offset on 85xx + + In the future the offsets to various blocks may not be in same location. + Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers + instead of getting it via &immap->im_gur. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 50c03c8cf494d91cdec39670d95337c743e16ec9 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Tue Nov 27 22:42:34 2007 -0600 + + Update MPC8544 DS config + + * Removed HAS_ETH2/HAS_ETH3 - MPC8544 only has TSEC1/2 + * Removed some misc environment setup + * Moved to using fdtfile & fdtaddr as fdt env var names + * Enabled CONFIG_CMDLINE_EDITING + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit addce57e2e4c49e77ffb2020a84690713bb18b47 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Mon Nov 26 17:12:24 2007 -0600 + + Update MPC8544DS to use libfdt + + Updated the MPC8544DS config to use libfdt and assume use of aliases for + ethernet, pci, and serial for the various fixups that are done. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit f852ce72f100cabd1f11c21c085a0ad8eca9fb65 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Thu Nov 29 00:15:30 2007 -0600 + + Add libfdt based ft_cpu_setup for mpc85xx + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 9692c2734a47f23b44a0f68042a3e2ca8d1bfb39 +Author: Stefan Roese <sr@denx.de> +Date: Sat Dec 8 08:25:09 2007 +0100 + + CFI: Coding style cleanup + + Signed-off-by: Stefan Roese <sr@denx.de> + +commit 81b20ccc2d795ae9a1199db5a50ad9c28d1e4d22 +Author: Michael Schwingen <michael@schwingen.org> +Date: Fri Dec 7 23:35:02 2007 +0100 + + CFI: support JEDEC flash roms in CFI-flash framework + + The following patch adds support for non-CFI flash ROMS, by hooking into the + CFI flash code and using most of its code, as recently discussed here in the + thread "Mixing CFI and non-CFI flashs". + + Signed-off-by: Michael Schwingen <michael@schwingen.org> + Signed-off-by: Stefan Roese <sr@denx.de> + +commit c01b17dd856fa120b2970f50d9598546a4927ec3 +Author: Gerald Van Baren <vanbaren@cideas.com> +Date: Wed Nov 28 21:24:50 2007 -0500 + + Conditionally compile fdt_fixup_ethernet() + + Fix compiler warnings: On boards that don't have ethernets defined, + don't compile fdt_fixup_ethernet(). + +commit 246d4ae6bc282bc1841224e1c5fc49dc925e0bf7 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Tue Nov 27 21:59:46 2007 -0600 + + Convert boards that set memory node to use fdt_fixup_memory() + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 151c8b09b35eebe8fd9139cb6c1d91c27b22f058 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Mon Nov 26 17:06:15 2007 -0600 + + Added fdt_fixup_stdout that uses aliases to set linux,stdout-path + + We use a combination of the serialN alias and CONFIG_CONS_INDEX to + determine which serial alias we should set linux,stdout-path to. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 3c9272813fad84c691d0e4989bb18a3ffebdebfc +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Mon Nov 26 14:57:45 2007 -0600 + + Add common memory fixup function + + Add the function fdt_fixup_memory() to fixup the /memory node of the fdt + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 9c9109e7fcf7ac2ca19c95b8ac54b8d1c773b157 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Mon Nov 26 11:19:12 2007 -0600 + + Conditionally compile fdt_support.c + + Modify common/Makefile to conditionally compile fdt_support.c based + on CONFIG_OF_LIBFDT. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit d88e7ba0980773479e1a64badb293116071b7ef0 +Author: Kumar Gala <galak@kernel.crashing.org> +Date: Mon Nov 26 10:41:40 2007 -0600 + + Fix build breakage due to libfdt import + + The IDS8247 got lost in the update and need an API update + do to rename of functions in libfdt. + + Signed-off-by: Kumar Gala <galak@kernel.crashing.org> + +commit 28f384b171bbf1fb2dafb1046e6d259a6b2f8714 +Author: Gerald Van Baren <vanbaren@cideas.com> +Date: Fri Nov 23 19:43:20 2007 -0500 + + Add spaces around the = in the fdt print format. + + Signed-off-by: Gerald Van Baren <vanbaren@cideas.com> + +commit 29592ecba3b932b9b152bcec6c0c0806412db4a3 +Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> +Date: Fri Dec 7 01:25:38 2007 +0900 + + sh: Moved driver of the SuperH dependence + + The composition of the directory in the drivers/ changed. + I moved SuperH serial driver and marubun PCMCIA driver. + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + +commit 41be969f4957115ed7b1fe8b890bfaee99d7a7a2 +Author: Wolfgang Denk <wd@denx.de> +Date: Thu Dec 6 10:21:19 2007 +0100 + + Release v1.3.1 + + Signed-off-by: Wolfgang Denk <wd@denx.de> + +commit cf5933ba1e97a1cd8f5f24070e820f21d976eaeb +Author: Wolfgang Denk <wd@denx.de> +Date: Thu Dec 6 10:21:03 2007 +0100 + + ADS5121 Board: fix compile problem. + + Signed-off-by: Wolfgang Denk <wd@denx.de> + +commit 8d4f040a3c15036a6ea25a9c39e7d89fefa8440d +Author: Wolfgang Denk <wd@denx.de> +Date: Mon Dec 3 00:15:28 2007 +0100 + + Prepare for 1.3.1-rc1 + + Signed-off-by: Wolfgang Denk <wd@denx.de> + +commit 260eea5676ca46903a335686cc020b29c4ca46fe +Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> +Date: Thu Nov 29 01:21:54 2007 +0900 + + sh: Add SuperH boards maintainer to MAINTAINERS file + + Add MS7750SE and MS7722SE's board maintainer to MAINTAINERS file. + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + +commit aa9c4f1d22701a92347c1c81f34d12c8ad3a3747 +Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> +Date: Thu Nov 29 00:13:04 2007 +0900 + + sh: Add ms7750se support in MAKEALL + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + +commit c7144373427a178332bf9754131c8c34c52c200a +Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> +Date: Tue Nov 27 09:44:53 2007 +0100 + + sh: Add sh3 and sh4 support in MAKEALL + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + +commit 130080874a3d28450098481a262c5f7c855e908d +Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> +Date: Sun Nov 25 02:51:17 2007 +0900 + + sh: Add document for SuperH. + + This document is a summary of information concerning SuperH of U-Boot. + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + +commit 33ecdc2f9d64926e1a6067b28f3a0aefc3b6d23d +Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> +Date: Sun Nov 25 02:39:31 2007 +0900 + + sh: Add marubun's pcmcia driver + + Marubun pcmcia is a chip for PCMCIA used with SuperH. + Of course, this can be used even by other architectures. + When use this driver, came to be able to use CompactFlash + and Ethernet. + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + +commit febd86b969b975289ed948f1ac0eb9722da41ced +Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> +Date: Sun Nov 25 02:32:13 2007 +0900 + + sh: Update SuperH SCIF driver + + - Changed volatile unsigned to vu_. + - Changed Makefile for kconfig. + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + commit a5f601fd1b1278deae5aa9fc27a232b0d1c1c788 Author: Wolfgang Denk <wd@denx.de> Date: Mon Nov 26 19:18:21 2007 +0100 @@ -1927,6 +2611,56 @@ Date: Mon Sep 24 00:08:37 2007 +0200 synchronizition with mainline +commit eda3e1e6619ad0bee94ae4b16c99d88e77e2af13 +Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> +Date: Sun Sep 23 02:42:38 2007 +0900 + + sh: Add support command of ide with sh + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + +commit d91ea45d15cf8e0987456bd211ffbb650824b6f1 +Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> +Date: Sun Sep 23 02:38:42 2007 +0900 + + sh: Update Makefile + + Add support MS7722SE01 to Makefile. + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + +commit 6c0bbdccd379f5c8702af9e0765294c2fb7472a6 +Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> +Date: Sun Sep 23 02:31:13 2007 +0900 + + sh: Add support Renesas sh7722 processor and Hitachi MS7722SE01 board + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + +commit 047375bfa4c3052fa50a748da7ff89e9dad3b364 +Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> +Date: Sun Sep 23 02:19:24 2007 +0900 + + sh: Update MS7750SE01 platform + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + +commit 516ad760db3553766267ada01b7d5d727faa4bbd +Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> +Date: Sun Sep 23 02:17:08 2007 +0900 + + sh: Remove comment out code from include/asm-sh/cpu_sh4.h + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + +commit b02bad128669e567fce87d8df823b06a0144b8db +Author: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> +Date: Sun Sep 23 02:12:30 2007 +0900 + + sh: Update core code of SuperH. + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + commit 66dcad3a9a53e0766d90e0084123bd8529522fb0 Author: Wolfgang Denk <wd@denx.de> Date: Thu Sep 20 00:04:14 2007 +0200 @@ -8634,6 +9368,24 @@ Date: Tue May 15 07:55:42 2007 -0700 Fix to compile JSE against 20070514 git of u-boot +commit 69df3c4da0c93017cceb25a366e794570bd0ed98 +Author: Nobuhiro Iwamatsu <iwamatsu@rahute.(none)> +Date: Sun May 13 21:01:03 2007 +0900 + + sh: MS7750SE support. + + This adds support for the Hitachi MS7750SE. + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + +commit 0b135cfc2e524dc249b75057b55dd4cc09842e27 +Author: Nobuhiro Iwamatsu <iwamatsu@rahute.(none)> +Date: Sun May 13 20:58:00 2007 +0900 + + sh: First support code of SuperH. + + Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + commit 61936667e86a250ae12fd2dc189d3588f0a59e0b Author: Stefan Roese <sr@denx.de> Date: Fri May 11 12:01:49 2007 +0200 diff --git a/MAINTAINERS b/MAINTAINERS index 5c68e5d74d..9052a196c4 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -634,7 +634,7 @@ Haavard Skinnemoen <hskinnemoen@atmel.com> ATSTK1002 AT32AP7000 ATSTK1003 AT32AP7001 ATSTK1004 AT32AP7002 - + ######################################################################### # SuperH Systems: # # # diff --git a/board/ms7722se/Makefile b/board/ms7722se/Makefile index 94469f7c6e..6dec0136c2 100644 --- a/board/ms7722se/Makefile +++ b/board/ms7722se/Makefile @@ -1,7 +1,7 @@ # # Copyright (C) 2007 # Nobuhiro Iwamatsu <iwamatsu@nigauri.org> -# +# # Copyright (C) 2007 # Kenati Technologies, Inc. # diff --git a/board/ms7722se/config.mk b/board/ms7722se/config.mk index e4ca55acad..4797d6f8f6 100644 --- a/board/ms7722se/config.mk +++ b/board/ms7722se/config.mk @@ -29,4 +29,3 @@ # TEXT_BASE = 0x8FFC0000 - diff --git a/board/ms7722se/lowlevel_init.S b/board/ms7722se/lowlevel_init.S index e0d519c55a..2024e27ffe 100644 --- a/board/ms7722se/lowlevel_init.S +++ b/board/ms7722se/lowlevel_init.S @@ -1,7 +1,7 @@ /* * Copyright (C) 2007 * Nobuhiro Iwamatsu <iwamatsu@nigauri.org> - * + * * Copyright (C) 2007 * Kenati Technologies, Inc. * @@ -52,19 +52,19 @@ lowlevel_init: mov.l r0, @r1 mov.l MSTPCR0_A, r1 ! Address of Power Control Register 0 - mov.l MSTPCR0_D, r0 ! + mov.l MSTPCR0_D, r0 ! mov.l r0, @r1 mov.l MSTPCR2_A, r1 ! Address of Power Control Register 2 - mov.l MSTPCR2_D, r0 ! + mov.l MSTPCR2_D, r0 ! mov.l r0, @r1 - mov.l SBSCR_A, r1 ! - mov.w SBSCR_D, r0 ! + mov.l SBSCR_A, r1 ! + mov.w SBSCR_D, r0 ! mov.w r0, @r1 - mov.l PSCR_A, r1 ! - mov.w PSCR_D, r0 ! + mov.l PSCR_A, r1 ! + mov.w PSCR_D, r0 ! mov.w r0, @r1 ! mov.l RWTCSR_A, r1 ! 0xA4520004 (Watchdog Control / Status Register) @@ -80,7 +80,7 @@ lowlevel_init: mov.w r0, @r1 mov.l FRQCR_A, r1 ! 0xA4150000 Frequency control register - mov.l FRQCR_D, r0 ! + mov.l FRQCR_D, r0 ! mov.l r0, @r1 mov.l CCR_A, r1 ! Address of Cache Control Register @@ -200,11 +200,9 @@ bsc_init: rts mov #0, r0 - - .align 2 -CCR_A: .long CCR +CCR_A: .long CCR MMUCR_A: .long MMUCR MSTPCR0_A: .long MSTPCR0 MSTPCR2_A: .long MSTPCR2 @@ -223,7 +221,7 @@ FRQCR_D: .long 0x07022538 PSELA_A: .long 0xa405014E PSELA_D: .word 0x0A10 - .align 2 + .align 2 DRVCR_A: .long 0xa405018A DRVCR_D: .word 0x0554 diff --git a/board/ms7722se/ms7722se.c b/board/ms7722se/ms7722se.c index 3eeb1b7d80..0d3d55cf5c 100644 --- a/board/ms7722se/ms7722se.c +++ b/board/ms7722se/ms7722se.c @@ -4,7 +4,7 @@ * * Copyright (C) 2007 * Kenati Technologies, Inc. - * + * * board/ms7722se/ms7722se.c * * This program is free software; you can redistribute it and/or @@ -57,4 +57,3 @@ void led_set_state (unsigned short value) { *((volatile unsigned short *) LED_BASE) = (value & 0xFF); } - diff --git a/board/ms7722se/u-boot.lds b/board/ms7722se/u-boot.lds index 24c218495c..692bc62918 100644 --- a/board/ms7722se/u-boot.lds +++ b/board/ms7722se/u-boot.lds @@ -32,19 +32,19 @@ SECTIONS Although size of SDRAM can be either 16 or 32 MBytes, we assume 16 MBytes (ie ignore upper half if the full 32 MBytes is present). - + NOTE: This address must match with the definition of TEXT_BASE in config.mk (in this directory). - + */ . = 0x8C000000 + (64*1024*1024) - (256*1024); - + PROVIDE (reloc_dst = .); PROVIDE (_ftext = .); PROVIDE (_fcode = .); PROVIDE (_start = .); - + .text : { cpu/sh4/start.o (.text) @@ -89,7 +89,7 @@ SECTIONS } PROVIDE (__u_boot_cmd_end = .); - PROVIDE (reloc_dst_end = .); + PROVIDE (reloc_dst_end = .); /* _reloc_dst_end = .; */ PROVIDE (bss_start = .); @@ -103,4 +103,3 @@ SECTIONS PROVIDE (_end = .); } - diff --git a/board/ms7750se/lowlevel_init.S b/board/ms7750se/lowlevel_init.S index 360c9fa173..d3e3cd5e8d 100644 --- a/board/ms7750se/lowlevel_init.S +++ b/board/ms7750se/lowlevel_init.S @@ -2,8 +2,8 @@ modified from SH-IPL+g Renesaso SuperH / Solution Enginge MS775xSE01 BSC setting. - Support CPU : SH7750/SH7750S/SH7750R/SH7751/SH7751R - + Support CPU : SH7750/SH7750S/SH7750R/SH7751/SH7751R + Coyright (c) 2007 Nobuhiro Iwamatsu <iwmatsu@nigauri.org> * See file CREDITS for list of people who contributed to this @@ -102,7 +102,7 @@ init_bsc: mov #0,r0 mov.b r0,@r1 - ! Do you need PCMCIA setting? + ! Do you need PCMCIA setting? ! If so, please add the lines here... mov.l RTCNT_A,r1 /* RTCNT Address */ @@ -165,7 +165,7 @@ WCR2_A: .long WCR2 WCR2_D: .long WCR2_D_VALUE /* Per-area access and burst wait states */ WCR3_A: .long WCR3 WCR3_D: .long WCR3_D_VALUE /* Address setup and data hold cycles */ -RTCSR_A: .long RTCSR +RTCSR_A: .long RTCSR RTCSR_D: .long 0xA518 /* RTCSR Write Code A5h Data 18h */ RTCNT_A: .long RTCNT RTCNT_D: .long 0xA500 /* RTCNT Write Code A5h Data 00h */ @@ -177,4 +177,3 @@ MCR_D1: .long MCR_D1_VALUE MCR_D2: .long MCR_D2_VALUE RFCR_A: .long RFCR RFCR_D: .long 0xA400 /* RFCR Write Code A4h Data 00h */ - diff --git a/board/ms7750se/ms7750se.c b/board/ms7750se/ms7750se.c index 1ae9dd13a5..d2d824c5a7 100644 --- a/board/ms7750se/ms7750se.c +++ b/board/ms7750se/ms7750se.c @@ -1,5 +1,5 @@ /* - * Copyright (C) 2007 + * Copyright (C) 2007 * Nobuhiro Iwamatsu <iwamatsu@nigauri.org> * * See file CREDITS for list of people who contributed to this diff --git a/board/ms7750se/u-boot.lds b/board/ms7750se/u-boot.lds index 24c218495c..692bc62918 100644 --- a/board/ms7750se/u-boot.lds +++ b/board/ms7750se/u-boot.lds @@ -32,19 +32,19 @@ SECTIONS Although size of SDRAM can be either 16 or 32 MBytes, we assume 16 MBytes (ie ignore upper half if the full 32 MBytes is present). - + NOTE: This address must match with the definition of TEXT_BASE in config.mk (in this directory). - + */ . = 0x8C000000 + (64*1024*1024) - (256*1024); - + PROVIDE (reloc_dst = .); PROVIDE (_ftext = .); PROVIDE (_fcode = .); PROVIDE (_start = .); - + .text : { cpu/sh4/start.o (.text) @@ -89,7 +89,7 @@ SECTIONS } PROVIDE (__u_boot_cmd_end = .); - PROVIDE (reloc_dst_end = .); + PROVIDE (reloc_dst_end = .); /* _reloc_dst_end = .; */ PROVIDE (bss_start = .); @@ -103,4 +103,3 @@ SECTIONS PROVIDE (_end = .); } - diff --git a/cpu/sh4/cache.c b/cpu/sh4/cache.c index 55acb31bc4..4e744d7145 100644 --- a/cpu/sh4/cache.c +++ b/cpu/sh4/cache.c @@ -30,36 +30,36 @@ * Jump to P2 area. * When handling TLB or caches, we need to do it from P2 area. */ -#define jump_to_P2() \ - do { \ +#define jump_to_P2() \ + do { \ unsigned long __dummy; \ - __asm__ __volatile__( \ - "mov.l 1f, %0\n\t" \ - "or %1, %0\n\t" \ - "jmp @%0\n\t" \ - " nop\n\t" \ - ".balign 4\n" \ - "1: .long 2f\n" \ - "2:" \ - : "=&r" (__dummy) \ - : "r" (0x20000000)); \ + __asm__ __volatile__( \ + "mov.l 1f, %0\n\t" \ + "or %1, %0\n\t" \ + "jmp @%0\n\t" \ + " nop\n\t" \ + ".balign 4\n" \ + "1: .long 2f\n" \ + "2:" \ + : "=&r" (__dummy) \ + : "r" (0x20000000)); \ } while (0) /* * Back to P1 area. */ -#define back_to_P1() \ - do { \ - unsigned long __dummy; \ - __asm__ __volatile__( \ - "nop;nop;nop;nop;nop;nop;nop\n\t" \ - "mov.l 1f, %0\n\t" \ - "jmp @%0\n\t" \ - " nop\n\t" \ - ".balign 4\n" \ - "1: .long 2f\n" \ - "2:" \ - : "=&r" (__dummy)); \ +#define back_to_P1() \ + do { \ + unsigned long __dummy; \ + __asm__ __volatile__( \ + "nop;nop;nop;nop;nop;nop;nop\n\t" \ + "mov.l 1f, %0\n\t" \ + "jmp @%0\n\t" \ + " nop\n\t" \ + ".balign 4\n" \ + "1: .long 2f\n" \ + "2:" \ + : "=&r" (__dummy)); \ } while (0) #define CACHE_VALID 1 diff --git a/cpu/sh4/config.mk b/cpu/sh4/config.mk index 2dc7b918d7..b3feb2a515 100644 --- a/cpu/sh4/config.mk +++ b/cpu/sh4/config.mk @@ -4,7 +4,7 @@ # # (C) Copyright 2007 # Nobuhiro Iwamatsu <iwamatsu@nigauri.org> -# +# # See file CREDITS for list of people who contributed to this # project. # diff --git a/cpu/sh4/cpu.c b/cpu/sh4/cpu.c index d76d5180e7..0ebf95180c 100644 --- a/cpu/sh4/cpu.c +++ b/cpu/sh4/cpu.c @@ -66,7 +66,7 @@ void icache_disable (void) int icache_status (void) { - return 0; + return 0; } void dcache_enable (void) diff --git a/cpu/sh4/interrupts.c b/cpu/sh4/interrupts.c index d310dd2c17..6988ecc7c2 100644 --- a/cpu/sh4/interrupts.c +++ b/cpu/sh4/interrupts.c @@ -25,7 +25,7 @@ int interrupt_init (void) { - return 0; + return 0; } void enable_interrupts (void) @@ -33,7 +33,6 @@ void enable_interrupts (void) } -int disable_interrupts (void){ - return 0; +int disable_interrupts (void){ + return 0; } - diff --git a/cpu/sh4/start.S b/cpu/sh4/start.S index d88b705ef0..a68ebb8c93 100644 --- a/cpu/sh4/start.S +++ b/cpu/sh4/start.S @@ -33,21 +33,21 @@ _start: bsr 1f nop 1: sts pr, r5 - mov.l ._reloc_dst, r4 - add #(_start-1b), r5 - mov.l ._reloc_dst_end, r6 + mov.l ._reloc_dst, r4 + add #(_start-1b), r5 + mov.l ._reloc_dst_end, r6 2: mov.l @r5+, r1 mov.l r1, @r4 add #4, r4 cmp/hs r6, r4 bf 2b - - mov.l ._bss_start, r4 - mov.l ._bss_end, r5 + + mov.l ._bss_start, r4 + mov.l ._bss_end, r5 mov #0, r1 -3: mov.l r1, @r4 /* bss clear */ +3: mov.l r1, @r4 /* bss clear */ add #4, r4 cmp/hs r5, r4 bf 3b @@ -56,8 +56,8 @@ _start: mov.l ._stack_init, r15 /* stack */ mov.l ._sh_generic_init, r0 - jsr @r0 - nop + jsr @r0 + nop loop: bra loop @@ -72,4 +72,3 @@ loop: ._gd_init: .long (_start - CFG_GBL_DATA_SIZE) ._stack_init: .long (_start - CFG_GBL_DATA_SIZE - CFG_MALLOC_LEN - 16) ._sh_generic_init: .long sh_generic_init - diff --git a/cpu/sh4/watchdog.c b/cpu/sh4/watchdog.c index 04723a7462..346e21714f 100644 --- a/cpu/sh4/watchdog.c +++ b/cpu/sh4/watchdog.c @@ -32,12 +32,12 @@ static void cnt_write (unsigned char value){ while (csr_read() & (1 << 5)) { /* delay */ } - *((volatile unsigned short *)(WDT_BASE + 0x00)) + *((volatile unsigned short *)(WDT_BASE + 0x00)) = ((unsigned short) value) | 0x5A00; } static void csr_write (unsigned char value){ - *((volatile unsigned short *)(WDT_BASE + 0x04)) + *((volatile unsigned short *)(WDT_BASE + 0x04)) = ((unsigned short) value) | 0xA500; } @@ -48,5 +48,3 @@ void reset_cpu (unsigned long ignored) { while(1); } - - diff --git a/doc/README.marubun-pcmcia b/doc/README.marubun-pcmcia index 73c9f7f53b..3ed5cd33c4 100644 --- a/doc/README.marubun-pcmcia +++ b/doc/README.marubun-pcmcia @@ -1,59 +1,59 @@ U-Boot MARUBUN MR-SHPC-01 PCMCIA controller driver Last update 21/11/2007 by Nobuhiro Iwamatsu - + ======================================================================================== -0. What's this? +0. What's this? This driver supports MARUBUN MR-SHPC-01. url: http://www.marubun.co.jp/product/semicon/devices/qgc18e0000002n2z.html (Sorry Japanese only.) - This chip is used with SuperH well, and adopted by the - reference board. + This chip is used with SuperH well, and adopted by the + reference board. ex. * MS7750SE01 * MS7722SE01 - * other - + * other + This chip doesn't support CardBus. -1. base source code +1. base source code The code is based on sources from the Linux kernel - ( arch/sh/kernel/cf-enabler.c ). + ( arch/sh/kernel/cf-enabler.c ). -2. How to use +2. How to use The options you have to specify in the config file are (with the value for my board as an example): * CONFIG_MARUBUN_PCCARD If you want to use this device driver, should define CONFIG_MARUBUN_PCCARD. ex. #define CONFIG_MARUBUN_PCCARD - + * CONFIG_PCMCIA_SLOT_A Most devices have only one slot. You should define CONFIG_PCMCIA_SLOT_A . ex. #define CONFIG_PCMCIA_SLOT_A 1 * CFG_MARUBUN_MRSHPC This is MR-SHPC-01 PCMCIA controler base address. - You should do the setting matched to your environment. - ex. #define CFG_MARUBUN_MRSHPC 0xb03fffe0 + You should do the setting matched to your environment. + ex. #define CFG_MARUBUN_MRSHPC 0xb03fffe0 ( for MS7722SE01 environment ) * CFG_MARUBUN_MW1 This is MR-SHPC-01 memory window base address. - You should do the setting matched to your environment. + You should do the setting matched to your environment. ex. #define CFG_MARUBUN_MW1 0xb0400000 ( for MS7722SE01 environment ) - + * CFG_MARUBUN_MW1 This is MR-SHPC-01 attribute window base address. - You should do the setting matched to your environment. + You should do the setting matched to your environment. ex. #define CFG_MARUBUN_MW2 0xb0500000 ( for MS7722SE01 environment ) - + * CFG_MARUBUN_MW1 This is MR-SHPC-01 I/O window base address. - You should do the setting matched to your environment. + You should do the setting matched to your environment. ex. #define CFG_MARUBUN_IO 0xb0600000 ( for MS7722SE01 environment ) diff --git a/doc/README.sh b/doc/README.sh index 0441a7a646..075d360e90 100644 --- a/doc/README.sh +++ b/doc/README.sh @@ -1,5 +1,5 @@ -U-Boot for Renesas SuperH +U-Boot for Renesas SuperH Last update 08/10/2007 by Nobuhiro Iwamatsu ================================================================================ @@ -9,10 +9,10 @@ U-Boot for Renesas SuperH ================================================================================ 1. Overview - SuperH has an original boot loader. However, source code is dirty, and + SuperH has an original boot loader. However, source code is dirty, and maintenance is not done. - To improve sharing and the maintenance of the code, Nobuhiro Iwamatsu - started the porting to u-boot in 2007. + To improve sharing and the maintenance of the code, Nobuhiro Iwamatsu + started the porting to u-boot in 2007. ================================================================================ 2. Supported CPUs @@ -33,13 +33,13 @@ U-Boot for Renesas SuperH ** README ** In SuperH, S-record and binary of made u-boot work on the memory. - When u-boot is written in the flash, it is necessary to change the - address by using 'objcopy'. + When u-boot is written in the flash, it is necessary to change the + address by using 'objcopy'. ex) shX-linux-objcopy -Ibinary -Osrec u-boot.bin u-boot.flash.srec - + ================================================================================ 4. Compiler - You can use the following of u-boot to compile. + You can use the following of u-boot to compile. - SuperH Linux Open site http://www.superh-linux.org/ - KPIT GNU tools @@ -52,11 +52,10 @@ U-Boot for Renesas SuperH - SH7710/SH7712 (SH3) - SH7780(SH4) - SH7785(SH4) - + 5.2. Boards - Many boards ;-) ================================================================================ Copyright (c) 2007 Nobuhiro Iwamatsu <iwamatsu@nigaur.org> - diff --git a/drivers/pcmcia/marubun_pcmcia.c b/drivers/pcmcia/marubun_pcmcia.c index 89b201526c..7b112af922 100644 --- a/drivers/pcmcia/marubun_pcmcia.c +++ b/drivers/pcmcia/marubun_pcmcia.c @@ -17,8 +17,8 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA - * - */ + * + */ #include <common.h> #include <config.h> @@ -34,7 +34,7 @@ #endif #if defined(CONFIG_PCMCIA) \ - && (defined(CONFIG_MARUBUN_PCCARD)) + && (defined(CONFIG_MARUBUN_PCCARD)) /* MR-SHPC-01 register */ #define MRSHPC_MODE (CFG_MARUBUN_MRSHPC + 4) @@ -79,14 +79,14 @@ int pcmcia_on (void) outw(0x0b00,MRSHPC_MW0CR2); /* common mode & bus width 16bit SWAP = 1 */ else outw(0x0300,MRSHPC_MW0CR2); /* common mode & bus width 16bit SWAP = 0 */ - + /* attribute window open */ outw(0x8a85,MRSHPC_MW1CR1); /* window 0xb8500000 */ if ((inw(MRSHPC_CSR) & 0x4000) != 0) outw(0x0a00,MRSHPC_MW1CR2); /* attribute mode & bus width 16bit SWAP = 1 */ else outw(0x0200,MRSHPC_MW1CR2); /* attribute mode & bus width 16bit SWAP = 0 */ - + /* I/O window open */ outw(0x8a86,MRSHPC_IOWCR1); /* I/O window 0xb8600000 */ outw(0x0008,MRSHPC_CDCR); /* I/O card mode */ @@ -94,7 +94,7 @@ int pcmcia_on (void) outw(0x0a00,MRSHPC_IOWCR2); /* bus width 16bit SWAP = 1 */ else outw(0x0200,MRSHPC_IOWCR2); /* bus width 16bit SWAP = 0 */ - + outw(0x0000,MRSHPC_ISR); outw(0x2000,MRSHPC_ICR); outb(0x00,(CFG_MARUBUN_MW2 + 0x206)); diff --git a/drivers/serial/serial_sh.c b/drivers/serial/serial_sh.c index 78186326f0..ee44ba2644 100644 --- a/drivers/serial/serial_sh.c +++ b/drivers/serial/serial_sh.c @@ -1,7 +1,7 @@ /* * SuperH SCIF device driver. * Copyright (c) 2007 Nobuhiro Iwamatsu - * + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or @@ -31,7 +31,7 @@ #endif #define SCSMR (vu_short *)(SCIF_BASE + 0x0) -#define SCBRR (vu_char *)(SCIF_BASE + 0x4) +#define SCBRR (vu_char *)(SCIF_BASE + 0x4) #define SCSCR (vu_short *)(SCIF_BASE + 0x8) #define SCFTDR (vu_char *)(SCIF_BASE + 0xC) #define SCFSR (vu_short *)(SCIF_BASE + 0x10) @@ -51,7 +51,7 @@ #endif #define SCR_RE (1 << 4) -#define SCR_TE (1 << 5) +#define SCR_TE (1 << 5) #define FCR_RFRST (1 << 1) /* RFCL */ #define FCR_TFRST (1 << 2) /* TFCL */ #define FSR_DR (1 << 0) @@ -69,7 +69,7 @@ void serial_setbrg (void) DECLARE_GLOBAL_DATA_PTR; int divisor = gd->baudrate * 32; - *SCBRR = (CONFIG_SYS_CLK_FREQ + (divisor / 2)) / + *SCBRR = (CONFIG_SYS_CLK_FREQ + (divisor / 2)) / (gd->baudrate * 32) - 1; } diff --git a/examples/stubs.c b/examples/stubs.c index 263dd8c3de..571c4d50a4 100644 --- a/examples/stubs.c +++ b/examples/stubs.c @@ -132,7 +132,7 @@ gd_t *global_data; */ #define EXPORT_FUNC(x) \ asm volatile ( \ -" .globl _" #x "\n_" \ +" .globl _" #x "\n_" \ #x ":\n" \ " P0 = [P5 + %0]\n" \ " P0 = [P0 + %1]\n" \ @@ -155,17 +155,17 @@ gd_t *global_data; /* * r13 holds the pointer to the global_data. r1 is a call clobbered. */ -#define EXPORT_FUNC(x) \ - asm volatile ( \ - " .align 2\n" \ - " .globl " #x "\n" \ - #x ":\n" \ - " mov r13, r1\n" \ - " add %0, r1\n" \ - " add %1, r1\n" \ - " jmp @r1\n" \ - " nop\n" \ - " nop\n" \ +#define EXPORT_FUNC(x) \ + asm volatile ( \ + " .align 2\n" \ + " .globl " #x "\n" \ + #x ":\n" \ + " mov r13, r1\n" \ + " add %0, r1\n" \ + " add %1, r1\n" \ + " jmp @r1\n" \ + " nop\n" \ + " nop\n" \ : : "i"(offsetof(gd_t, jt)), "i"(XF_ ## x * sizeof(void *)) : "r1"); #else #error stubs definition missing for this architecture diff --git a/include/asm-sh/bitops.h b/include/asm-sh/bitops.h index 529d0f2dbb..410fba46ef 100644 --- a/include/asm-sh/bitops.h +++ b/include/asm-sh/bitops.h @@ -2,7 +2,6 @@ #define __ASM_SH_BITOPS_H #ifdef __KERNEL__ -//#include <asm/system.h> #include <asm/irqflags.h> /* For __swab32 */ #include <asm/byteorder.h> @@ -99,8 +98,6 @@ static inline int test_and_change_bit(int nr, volatile void * addr) return retval; } -//#include <asm-generic/bitops/non-atomic.h> - static inline unsigned long ffz(unsigned long word) { unsigned long result; @@ -121,46 +118,34 @@ static inline unsigned long ffz(unsigned long word) * * Undefined if no bit exists, so code should check against 0 first. */ -static inline int ffs(int x) +static inline int ffs (int x) { - int r = 1; - - if (!x) - return 0; - if (!(x & 0xffff)) { - x >>= 16; - r += 16; - } - if (!(x & 0xff)) { - x >>= 8; - r += 8; - } - if (!(x & 0xf)) { - x >>= 4; - r += 4; - } - if (!(x & 3)) { - x >>= 2; - r += 2; - } - if (!(x & 1)) { - x >>= 1; - r += 1; - } - return r; + int r = 1; + + if (!x) + return 0; + if (!(x & 0xffff)) { + x >>= 16; + r += 16; + } + if (!(x & 0xff)) { + x >>= 8; + r += 8; + } + if (!(x & 0xf)) { + x >>= 4; + r += 4; + } + if (!(x & 3)) { + x >>= 2; + r += 2; + } + if (!(x & 1)) { + x >>= 1; + r += 1; + } + return r; } - -#if 0 -#include <asm-generic/bitops/find.h> -#include <asm-generic/bitops/ffs.h> -#include <asm-generic/bitops/hweight.h> -#include <asm-generic/bitops/sched.h> -#include <asm-generic/bitops/ext2-non-atomic.h> -#include <asm-generic/bitops/ext2-atomic.h> -#include <asm-generic/bitops/minix.h> -#include <asm-generic/bitops/fls.h> -#include <asm-generic/bitops/fls64.h> -#endif #endif /* __KERNEL__ */ #endif /* __ASM_SH_BITOPS_H */ diff --git a/include/asm-sh/byteorder.h b/include/asm-sh/byteorder.h index 8836e657de..25626a0760 100644 --- a/include/asm-sh/byteorder.h +++ b/include/asm-sh/byteorder.h @@ -28,4 +28,3 @@ #endif #endif - diff --git a/include/asm-sh/cpu_sh7722.h b/include/asm-sh/cpu_sh7722.h index fb63c6ea49..13d4a77ede 100644 --- a/include/asm-sh/cpu_sh7722.h +++ b/include/asm-sh/cpu_sh7722.h @@ -31,13 +31,13 @@ #define INTEVT 0xFF000028 /* MMU */ -#define PTEH 0xFF000000 -#define PTEL 0xFF000004 -#define TTB 0xFF000008 -#define TEA 0xFF00000C -#define MMUCR 0xFF000010 -#define PASCR 0xFF000070 -#define IRMCR 0xFF000078 +#define PTEH 0xFF000000 +#define PTEL 0xFF000004 +#define TTB 0xFF000008 +#define TEA 0xFF00000C +#define MMUCR 0xFF000010 +#define PASCR 0xFF000070 +#define IRMCR 0xFF000078 /* CACHE */ #define CCR 0xFF00001C @@ -325,7 +325,7 @@ #define SPICR1 0xA4420030 /* SCIF */ -/* +/* #define SCSMR 0xFFE00000 #define SCBRR 0xFFE00004 #define SCSCR 0xFFE00008 @@ -1334,4 +1334,4 @@ #define SDDRL 0xFC11000A #define SDINT 0xFC110018 -#endif /* _ASM_CPU_SH7722_H_ */ +#endif /* _ASM_CPU_SH7722_H_ */ diff --git a/include/asm-sh/cpu_sh7750.h b/include/asm-sh/cpu_sh7750.h index 9993e63203..bb6461a6bf 100644 --- a/include/asm-sh/cpu_sh7750.h +++ b/include/asm-sh/cpu_sh7750.h @@ -1,7 +1,7 @@ /* * (C) Copyright 2007 Nobuhiro Iwamatsu <iwamatsu@nigauri.org> * - * SH7750/SH7750S/SH7750R/SH7751/SH7751R + * SH7750/SH7750S/SH7750R/SH7751/SH7751R * Internal I/O register * * This program is free software; you can redistribute it and/or diff --git a/include/asm-sh/posix_types.h b/include/asm-sh/posix_types.h index 4bb9f7e26f..c9d9fb84f1 100644 --- a/include/asm-sh/posix_types.h +++ b/include/asm-sh/posix_types.h @@ -68,7 +68,7 @@ static __inline__ void __FD_CLR(unsigned long __fd, __kernel_fd_set *__fdsetp) #undef __FD_ISSET static __inline__ int __FD_ISSET(unsigned long __fd, const __kernel_fd_set *__p) -{ +{ unsigned long __tmp = __fd / __NFDBITS; unsigned long __rem = __fd % __NFDBITS; return (__p->fds_bits[__tmp] & (1UL<<__rem)) != 0; diff --git a/include/asm-sh/u-boot.h b/include/asm-sh/u-boot.h index c74e97cdfb..b79644cfd2 100644 --- a/include/asm-sh/u-boot.h +++ b/include/asm-sh/u-boot.h @@ -25,7 +25,6 @@ #ifndef __ASM_SH_U_BOOT_H_ #define __ASM_SH_U_BOOT_H_ - typedef struct bd_info { unsigned long bi_memstart; /* start of DRAM memory */ unsigned long bi_memsize; /* size of DRAM memory in bytes */ @@ -41,4 +40,3 @@ typedef struct bd_info { } bd_t; #endif - diff --git a/include/configs/ms7722se.h b/include/configs/ms7722se.h index 18e985118c..ae0d018515 100644 --- a/include/configs/ms7722se.h +++ b/include/configs/ms7722se.h @@ -25,7 +25,7 @@ #ifndef __MS7722SE_H #define __MS7722SE_H -#undef DEBUG +#undef DEBUG #define CONFIG_SH 1 #define CONFIG_SH4 1 #define CONFIG_CPU_SH7722 1 @@ -56,7 +56,6 @@ /* MEMORY */ #define MS7722SE_SDRAM_BASE (0x8C000000) #define MS7722SE_FLASH_BASE_1 (0xA0000000) -//#define MS7722SE_FLASH_BASE_1 (0xA1000000) #define MS7722SE_FLASH_BANK_SIZE (8*1024 * 1024) #define CFG_LONGHELP /* undef to save memory */ @@ -87,12 +86,12 @@ #define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 4 * 1024 * 1024) /* default load address for scripts ?!? */ -#define CFG_MONITOR_BASE (MS7722SE_FLASH_BASE_1) /* Address of u-boot image +#define CFG_MONITOR_BASE (MS7722SE_FLASH_BASE_1) /* Address of u-boot image in Flash (NOT run time address in SDRAM) ?!? */ #define CFG_MONITOR_LEN (128 * 1024) /* */ #define CFG_MALLOC_LEN (256 * 1024) /* Size of DRAM reserved for malloc() use */ #define CFG_GBL_DATA_SIZE (256) /* size in bytes reserved for initial data */ -#define CFG_BOOTMAPSZ (8 * 1024 * 1024) +#define CFG_BOOTMAPSZ (8 * 1024 * 1024) /* FLASH */ #define CFG_FLASH_CFI @@ -102,7 +101,7 @@ #define CFG_FLASH_BASE (MS7722SE_FLASH_BASE_1) /* Physical start address of Flash memory */ -#define CFG_MAX_FLASH_SECT 150 /* Max number of sectors on each +#define CFG_MAX_FLASH_SECT 150 /* Max number of sectors on each Flash chip */ /* if you use all NOR Flash , you change dip-switch. Please see MS7722SE01 Manual. */ @@ -131,7 +130,7 @@ /* Board Clock */ #define CONFIG_SYS_CLK_FREQ 33333333 -#define TMU_CLK_DIVIDER (4) /* 4 (default), 16, 64, 256 or 1024 */ +#define TMU_CLK_DIVIDER (4) /* 4 (default), 16, 64, 256 or 1024 */ #define CFG_HZ (CONFIG_SYS_CLK_FREQ / TMU_CLK_DIVIDER) #endif /* __MS7722SE_H */ diff --git a/include/configs/ms7750se.h b/include/configs/ms7750se.h index 7925f209d7..36681568f8 100644 --- a/include/configs/ms7750se.h +++ b/include/configs/ms7750se.h @@ -37,7 +37,7 @@ /* * Command line configuration. */ -//#include <config_cmd_default.h> +/*#include <config_cmd_default.h>*/ #define CONFIG_CMD_DFL #define CONFIG_CMD_FLASH @@ -56,7 +56,7 @@ #define CFG_SDRAM_BASE (0x8C000000) #define CFG_SDRAM_SIZE (64 * 1024 * 1024) -#define CFG_LONGHELP +#define CFG_LONGHELP #define CFG_PROMPT "=> " #define CFG_CBSIZE 256 #define CFG_PBSIZE 256 @@ -71,7 +71,7 @@ /* NOR Flash */ /* #define CFG_FLASH_BASE (0xA1000000)*/ #define CFG_FLASH_BASE (0xA0000000) -#define CFG_MAX_FLASH_BANKS (1) /* Max number of +#define CFG_MAX_FLASH_BANKS (1) /* Max number of * Flash memory banks */ #define CFG_MAX_FLASH_SECT 142 diff --git a/lib_sh/Makefile b/lib_sh/Makefile index c84276af88..cf127a826c 100644 --- a/lib_sh/Makefile +++ b/lib_sh/Makefile @@ -22,7 +22,7 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(ARCH).a -SOBJS = +SOBJS = COBJS = board.o sh_linux.o # time.o diff --git a/lib_sh/board.c b/lib_sh/board.c index c63ac0313a..2cd60d76be 100644 --- a/lib_sh/board.c +++ b/lib_sh/board.c @@ -47,7 +47,7 @@ static void mem_malloc_init (void) mem_malloc_start = (TEXT_BASE - CFG_GBL_DATA_SIZE - CFG_MALLOC_LEN); mem_malloc_end = (mem_malloc_start + CFG_MALLOC_LEN - 16); mem_malloc_brk = mem_malloc_start; - memset ((void *) mem_malloc_start, 0, + memset ((void *) mem_malloc_start, 0, (mem_malloc_end - mem_malloc_start)); } @@ -191,7 +191,7 @@ void sh_generic_init (void) puts ("Net: "); eth_initialize(gd->bd); - if ((s = getenv ("bootfile")) != NULL) { + if ((s = getenv ("bootfile")) != NULL) { copy_filename (BootFile, s, sizeof (BootFile)); } #endif /* CONFIG_CMD_NET */ diff --git a/lib_sh/sh_linux.c b/lib_sh/sh_linux.c index acd47b5db7..14b6815cd4 100644 --- a/lib_sh/sh_linux.c +++ b/lib_sh/sh_linux.c @@ -28,7 +28,7 @@ extern image_header_t header; /* common/cmd_bootm.c */ /* The SH kernel reads arguments from the empty zero page at location - * 0 at the start of SDRAM. The following are copied from + * 0 at the start of SDRAM. The following are copied from * arch/sh/kernel/setup.c and may require tweaking if the kernel sources * change. */ @@ -72,4 +72,3 @@ void do_bootm_linux (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[], kernel(); } - |
