diff options
| -rw-r--r-- | arch/arm/Kconfig | 2 | ||||
| -rw-r--r-- | arch/arm/Kconfig.debug | 64 | ||||
| -rw-r--r-- | arch/arm/include/asm/macro.h | 2 | ||||
| -rw-r--r-- | arch/arm/include/debug/8250.S | 52 | ||||
| -rw-r--r-- | arch/arm/lib/Makefile | 2 | ||||
| -rw-r--r-- | arch/arm/lib/debug.S | 136 | ||||
| -rw-r--r-- | include/linux/serial_reg.h | 388 |
7 files changed, 645 insertions, 1 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 22eb2d5854..79ccc06d5c 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -950,4 +950,6 @@ source "board/woodburn/Kconfig" source "board/xaeniax/Kconfig" source "board/zipitz2/Kconfig" +source "arch/arm/Kconfig.debug" + endmenu diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug new file mode 100644 index 0000000000..624bcf4682 --- /dev/null +++ b/arch/arm/Kconfig.debug @@ -0,0 +1,64 @@ +menu "ARM debug" + +config DEBUG_LL + bool "Low-level debugging functions" + depends on !ARM64 + help + Say Y here to include definitions of printascii, printch, printhex + in U-Boot. This is helpful if you are debugging code that + executes before the console is initialized. + +choice + prompt "Low-level debugging port" + depends on DEBUG_LL + + config DEBUG_LL_UART_8250 + bool "Low-level debugging via 8250 UART" + help + Say Y here if you wish the debug print routes to direct + their output to an 8250 UART. You can use this option + to provide the parameters for the 8250 UART rather than + selecting one of the platform specific options above if + you know the parameters for the port. + + This option is preferred over the platform specific + options; the platform specific options are deprecated + and will be soon removed. + +endchoice + +config DEBUG_LL_INCLUDE + string + depends on DEBUG_LL + default "debug/8250.S" if DEBUG_LL_UART_8250 || DEBUG_UART_8250 + default "mach/debug-macro.S" + +# Compatibility options for 8250 +config DEBUG_UART_8250 + bool + +config DEBUG_UART_PHYS + hex "Physical base address of debug UART" + depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250 + +# This is not used in U-Boot +config DEBUG_UART_VIRT + hex + default DEBUG_UART_PHYS + depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250 + +config DEBUG_UART_8250_SHIFT + int "Register offset shift for the 8250 debug UART" + depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250 + default 2 + +config DEBUG_UART_8250_WORD + bool "Use 32-bit accesses for 8250 UART" + depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250 + depends on DEBUG_UART_8250_SHIFT >= 2 + +config DEBUG_UART_8250_FLOW_CONTROL + bool "Enable flow control for 8250 UART" + depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250 + +endmenu diff --git a/arch/arm/include/asm/macro.h b/arch/arm/include/asm/macro.h index 541b443254..1c8c4251ee 100644 --- a/arch/arm/include/asm/macro.h +++ b/arch/arm/include/asm/macro.h @@ -193,7 +193,7 @@ lr .req x30 0 : wfi ldr \wreg2, [\xreg1, GICC_AIAR] str \wreg2, [\xreg1, GICC_AEOIR] - and \wreg2, \wreg2, #3ff + and \wreg2, \wreg2, #0x3ff cbnz \wreg2, 0b .endm #endif diff --git a/arch/arm/include/debug/8250.S b/arch/arm/include/debug/8250.S new file mode 100644 index 0000000000..d47a892652 --- /dev/null +++ b/arch/arm/include/debug/8250.S @@ -0,0 +1,52 @@ +/* + * arch/arm/include/debug/8250.S + * + * Copyright (C) 1994-2013 Russell King + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#include <linux/serial_reg.h> + + .macro addruart, rp, rv, tmp + ldr \rp, =CONFIG_DEBUG_UART_PHYS + ldr \rv, =CONFIG_DEBUG_UART_VIRT + .endm + +#ifdef CONFIG_DEBUG_UART_8250_WORD + .macro store, rd, rx:vararg + str \rd, \rx + .endm + + .macro load, rd, rx:vararg + ldr \rd, \rx + .endm +#else + .macro store, rd, rx:vararg + strb \rd, \rx + .endm + + .macro load, rd, rx:vararg + ldrb \rd, \rx + .endm +#endif + +#define UART_SHIFT CONFIG_DEBUG_UART_8250_SHIFT + + .macro senduart,rd,rx + store \rd, [\rx, #UART_TX << UART_SHIFT] + .endm + + .macro busyuart,rd,rx +1002: load \rd, [\rx, #UART_LSR << UART_SHIFT] + and \rd, \rd, #UART_LSR_TEMT | UART_LSR_THRE + teq \rd, #UART_LSR_TEMT | UART_LSR_THRE + bne 1002b + .endm + + .macro waituart,rd,rx +#ifdef CONFIG_DEBUG_UART_8250_FLOW_CONTROL +1001: load \rd, [\rx, #UART_MSR << UART_SHIFT] + tst \rd, #UART_MSR_CTS + beq 1001b +#endif + .endm diff --git a/arch/arm/lib/Makefile b/arch/arm/lib/Makefile index 1ef240047f..d74e4b8415 100644 --- a/arch/arm/lib/Makefile +++ b/arch/arm/lib/Makefile @@ -48,6 +48,8 @@ ifndef CONFIG_ARM64 obj-y += cache-cp15.o endif +obj-$(CONFIG_DEBUG_LL) += debug.o + # For EABI conformant tool chains, provide eabi_compat() ifneq (,$(findstring -mabi=aapcs-linux,$(PLATFORM_CPPFLAGS))) extra-y += eabi_compat.o diff --git a/arch/arm/lib/debug.S b/arch/arm/lib/debug.S new file mode 100644 index 0000000000..760ba74a3c --- /dev/null +++ b/arch/arm/lib/debug.S @@ -0,0 +1,136 @@ +/* + * linux/arch/arm/kernel/debug.S + * + * Copyright (C) 1994-1999 Russell King + * + * SPDX-License-Identifier: GPL-2.0+ + * + * 32-bit debugging code + */ +#include <linux/linkage.h> +#include <asm/assembler.h> + + .text + +/* + * Some debugging routines (useful if you've got MM problems and + * printk isn't working). For DEBUGGING ONLY!!! Do not leave + * references to these in a production kernel! + */ + +#if !defined(CONFIG_DEBUG_SEMIHOSTING) +#include CONFIG_DEBUG_LL_INCLUDE +#endif + +#ifdef CONFIG_MMU + .macro addruart_current, rx, tmp1, tmp2 + addruart \tmp1, \tmp2, \rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 + moveq \rx, \tmp1 + movne \rx, \tmp2 + .endm + +#else /* !CONFIG_MMU */ + .macro addruart_current, rx, tmp1, tmp2 + addruart \rx, \tmp1, \tmp2 + .endm + +#endif /* CONFIG_MMU */ + +/* + * Useful debugging routines + */ +ENTRY(printhex8) + mov r1, #8 + b printhex +ENDPROC(printhex8) + +ENTRY(printhex4) + mov r1, #4 + b printhex +ENDPROC(printhex4) + +ENTRY(printhex2) + mov r1, #2 +printhex: adr r2, hexbuf + add r3, r2, r1 + mov r1, #0 + strb r1, [r3] +1: and r1, r0, #15 + mov r0, r0, lsr #4 + cmp r1, #10 + addlt r1, r1, #'0' + addge r1, r1, #'a' - 10 + strb r1, [r3, #-1]! + teq r3, r2 + bne 1b + mov r0, r2 + b printascii +ENDPROC(printhex2) + +hexbuf: .space 16 + + .ltorg + +#ifndef CONFIG_DEBUG_SEMIHOSTING + +ENTRY(printascii) + addruart_current r3, r1, r2 + b 2f +1: waituart r2, r3 + senduart r1, r3 + busyuart r2, r3 + teq r1, #'\n' + moveq r1, #'\r' + beq 1b +2: teq r0, #0 + ldrneb r1, [r0], #1 + teqne r1, #0 + bne 1b + mov pc, lr +ENDPROC(printascii) + +ENTRY(printch) + addruart_current r3, r1, r2 + mov r1, r0 + mov r0, #0 + b 1b +ENDPROC(printch) + +#ifdef CONFIG_MMU +ENTRY(debug_ll_addr) + addruart r2, r3, ip + str r2, [r0] + str r3, [r1] + mov pc, lr +ENDPROC(debug_ll_addr) +#endif + +#else + +ENTRY(printascii) + mov r1, r0 + mov r0, #0x04 @ SYS_WRITE0 + ARM( svc #0x123456 ) + THUMB( svc #0xab ) + mov pc, lr +ENDPROC(printascii) + +ENTRY(printch) + adr r1, hexbuf + strb r0, [r1] + mov r0, #0x03 @ SYS_WRITEC + ARM( svc #0x123456 ) + THUMB( svc #0xab ) + mov pc, lr +ENDPROC(printch) + +ENTRY(debug_ll_addr) + mov r2, #0 + str r2, [r0] + str r2, [r1] + mov pc, lr +ENDPROC(debug_ll_addr) + +#endif diff --git a/include/linux/serial_reg.h b/include/linux/serial_reg.h new file mode 100644 index 0000000000..9214b67b11 --- /dev/null +++ b/include/linux/serial_reg.h @@ -0,0 +1,388 @@ +/* + * include/linux/serial_reg.h + * + * Copyright (C) 1992, 1994 by Theodore Ts'o. + * + * SPDX-License-Identifier: GPL-2.0+ + * + * These are the UART port assignments, expressed as offsets from the base + * register. These assignments should hold for any serial port based on + * a 8250, 16450, or 16550(A). + */ + +#ifndef _LINUX_SERIAL_REG_H +#define _LINUX_SERIAL_REG_H + +/* + * DLAB=0 + */ +#define UART_RX 0 /* In: Receive buffer */ +#define UART_TX 0 /* Out: Transmit buffer */ + +#define UART_IER 1 /* Out: Interrupt Enable Register */ +#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */ +#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */ +#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */ +#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */ +/* + * Sleep mode for ST16650 and TI16750. For the ST16650, EFR[4]=1 + */ +#define UART_IERX_SLEEP 0x10 /* Enable sleep mode */ + +#define UART_IIR 2 /* In: Interrupt ID Register */ +#define UART_IIR_NO_INT 0x01 /* No interrupts pending */ +#define UART_IIR_ID 0x0e /* Mask for the interrupt ID */ +#define UART_IIR_MSI 0x00 /* Modem status interrupt */ +#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ +#define UART_IIR_RDI 0x04 /* Receiver data interrupt */ +#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ + +#define UART_IIR_BUSY 0x07 /* DesignWare APB Busy Detect */ + +#define UART_IIR_RX_TIMEOUT 0x0c /* OMAP RX Timeout interrupt */ +#define UART_IIR_XOFF 0x10 /* OMAP XOFF/Special Character */ +#define UART_IIR_CTS_RTS_DSR 0x20 /* OMAP CTS/RTS/DSR Change */ + +#define UART_FCR 2 /* Out: FIFO Control Register */ +#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */ +#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */ +#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */ +#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */ +/* + * Note: The FIFO trigger levels are chip specific: + * RX:76 = 00 01 10 11 TX:54 = 00 01 10 11 + * PC16550D: 1 4 8 14 xx xx xx xx + * TI16C550A: 1 4 8 14 xx xx xx xx + * TI16C550C: 1 4 8 14 xx xx xx xx + * ST16C550: 1 4 8 14 xx xx xx xx + * ST16C650: 8 16 24 28 16 8 24 30 PORT_16650V2 + * NS16C552: 1 4 8 14 xx xx xx xx + * ST16C654: 8 16 56 60 8 16 32 56 PORT_16654 + * TI16C750: 1 16 32 56 xx xx xx xx PORT_16750 + * TI16C752: 8 16 56 60 8 16 32 56 + * Tegra: 1 4 8 14 16 8 4 1 PORT_TEGRA + */ +#define UART_FCR_R_TRIG_00 0x00 +#define UART_FCR_R_TRIG_01 0x40 +#define UART_FCR_R_TRIG_10 0x80 +#define UART_FCR_R_TRIG_11 0xc0 +#define UART_FCR_T_TRIG_00 0x00 +#define UART_FCR_T_TRIG_01 0x10 +#define UART_FCR_T_TRIG_10 0x20 +#define UART_FCR_T_TRIG_11 0x30 + +#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */ +#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */ +#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */ +#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */ +#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */ +/* 16650 definitions */ +#define UART_FCR6_R_TRIGGER_8 0x00 /* Mask for receive trigger set at 1 */ +#define UART_FCR6_R_TRIGGER_16 0x40 /* Mask for receive trigger set at 4 */ +#define UART_FCR6_R_TRIGGER_24 0x80 /* Mask for receive trigger set at 8 */ +#define UART_FCR6_R_TRIGGER_28 0xC0 /* Mask for receive trigger set at 14 */ +#define UART_FCR6_T_TRIGGER_16 0x00 /* Mask for transmit trigger set at 16 */ +#define UART_FCR6_T_TRIGGER_8 0x10 /* Mask for transmit trigger set at 8 */ +#define UART_FCR6_T_TRIGGER_24 0x20 /* Mask for transmit trigger set at 24 */ +#define UART_FCR6_T_TRIGGER_30 0x30 /* Mask for transmit trigger set at 30 */ +#define UART_FCR7_64BYTE 0x20 /* Go into 64 byte mode (TI16C750) */ + +#define UART_LCR 3 /* Out: Line Control Register */ +/* + * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting + * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits. + */ +#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ +#define UART_LCR_SBC 0x40 /* Set break control */ +#define UART_LCR_SPAR 0x20 /* Stick parity (?) */ +#define UART_LCR_EPAR 0x10 /* Even parity select */ +#define UART_LCR_PARITY 0x08 /* Parity Enable */ +#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 bit, 1=2 bits */ +#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */ +#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */ +#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */ +#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */ + +/* + * Access to some registers depends on register access / configuration + * mode. + */ +#define UART_LCR_CONF_MODE_A UART_LCR_DLAB /* Configutation mode A */ +#define UART_LCR_CONF_MODE_B 0xBF /* Configutation mode B */ + +#define UART_MCR 4 /* Out: Modem Control Register */ +#define UART_MCR_CLKSEL 0x80 /* Divide clock by 4 (TI16C752, EFR[4]=1) */ +#define UART_MCR_TCRTLR 0x40 /* Access TCR/TLR (TI16C752, EFR[4]=1) */ +#define UART_MCR_XONANY 0x20 /* Enable Xon Any (TI16C752, EFR[4]=1) */ +#define UART_MCR_AFE 0x20 /* Enable auto-RTS/CTS (TI16C550C/TI16C750) */ +#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */ +#define UART_MCR_OUT2 0x08 /* Out2 complement */ +#define UART_MCR_OUT1 0x04 /* Out1 complement */ +#define UART_MCR_RTS 0x02 /* RTS complement */ +#define UART_MCR_DTR 0x01 /* DTR complement */ + +#define UART_LSR 5 /* In: Line Status Register */ +#define UART_LSR_FIFOE 0x80 /* Fifo error */ +#define UART_LSR_TEMT 0x40 /* Transmitter empty */ +#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */ +#define UART_LSR_BI 0x10 /* Break interrupt indicator */ +#define UART_LSR_FE 0x08 /* Frame error indicator */ +#define UART_LSR_PE 0x04 /* Parity error indicator */ +#define UART_LSR_OE 0x02 /* Overrun error indicator */ +#define UART_LSR_DR 0x01 /* Receiver data ready */ +#define UART_LSR_BRK_ERROR_BITS 0x1E /* BI, FE, PE, OE bits */ + +#define UART_MSR 6 /* In: Modem Status Register */ +#define UART_MSR_DCD 0x80 /* Data Carrier Detect */ +#define UART_MSR_RI 0x40 /* Ring Indicator */ +#define UART_MSR_DSR 0x20 /* Data Set Ready */ +#define UART_MSR_CTS 0x10 /* Clear to Send */ +#define UART_MSR_DDCD 0x08 /* Delta DCD */ +#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */ +#define UART_MSR_DDSR 0x02 /* Delta DSR */ +#define UART_MSR_DCTS 0x01 /* Delta CTS */ +#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */ + +#define UART_SCR 7 /* I/O: Scratch Register */ + +/* + * DLAB=1 + */ +#define UART_DLL 0 /* Out: Divisor Latch Low */ +#define UART_DLM 1 /* Out: Divisor Latch High */ + +/* + * LCR=0xBF (or DLAB=1 for 16C660) + */ +#define UART_EFR 2 /* I/O: Extended Features Register */ +#define UART_XR_EFR 9 /* I/O: Extended Features Register (XR17D15x) */ +#define UART_EFR_CTS 0x80 /* CTS flow control */ +#define UART_EFR_RTS 0x40 /* RTS flow control */ +#define UART_EFR_SCD 0x20 /* Special character detect */ +#define UART_EFR_ECB 0x10 /* Enhanced control bit */ +/* + * the low four bits control software flow control + */ + +/* + * LCR=0xBF, TI16C752, ST16650, ST16650A, ST16654 + */ +#define UART_XON1 4 /* I/O: Xon character 1 */ +#define UART_XON2 5 /* I/O: Xon character 2 */ +#define UART_XOFF1 6 /* I/O: Xoff character 1 */ +#define UART_XOFF2 7 /* I/O: Xoff character 2 */ + +/* + * EFR[4]=1 MCR[6]=1, TI16C752 + */ +#define UART_TI752_TCR 6 /* I/O: transmission control register */ +#define UART_TI752_TLR 7 /* I/O: trigger level register */ + +/* + * LCR=0xBF, XR16C85x + */ +#define UART_TRG 0 /* FCTR bit 7 selects Rx or Tx + * In: Fifo count + * Out: Fifo custom trigger levels */ +/* + * These are the definitions for the Programmable Trigger Register + */ +#define UART_TRG_1 0x01 +#define UART_TRG_4 0x04 +#define UART_TRG_8 0x08 +#define UART_TRG_16 0x10 +#define UART_TRG_32 0x20 +#define UART_TRG_64 0x40 +#define UART_TRG_96 0x60 +#define UART_TRG_120 0x78 +#define UART_TRG_128 0x80 + +#define UART_FCTR 1 /* Feature Control Register */ +#define UART_FCTR_RTS_NODELAY 0x00 /* RTS flow control delay */ +#define UART_FCTR_RTS_4DELAY 0x01 +#define UART_FCTR_RTS_6DELAY 0x02 +#define UART_FCTR_RTS_8DELAY 0x03 +#define UART_FCTR_IRDA 0x04 /* IrDa data encode select */ +#define UART_FCTR_TX_INT 0x08 /* Tx interrupt type select */ +#define UART_FCTR_TRGA 0x00 /* Tx/Rx 550 trigger table select */ +#define UART_FCTR_TRGB 0x10 /* Tx/Rx 650 trigger table select */ +#define UART_FCTR_TRGC 0x20 /* Tx/Rx 654 trigger table select */ +#define UART_FCTR_TRGD 0x30 /* Tx/Rx 850 programmable trigger select */ +#define UART_FCTR_SCR_SWAP 0x40 /* Scratch pad register swap */ +#define UART_FCTR_RX 0x00 /* Programmable trigger mode select */ +#define UART_FCTR_TX 0x80 /* Programmable trigger mode select */ + +/* + * LCR=0xBF, FCTR[6]=1 + */ +#define UART_EMSR 7 /* Extended Mode Select Register */ +#define UART_EMSR_FIFO_COUNT 0x01 /* Rx/Tx select */ +#define UART_EMSR_ALT_COUNT 0x02 /* Alternating count select */ + +/* + * The Intel XScale on-chip UARTs define these bits + */ +#define UART_IER_DMAE 0x80 /* DMA Requests Enable */ +#define UART_IER_UUE 0x40 /* UART Unit Enable */ +#define UART_IER_NRZE 0x20 /* NRZ coding Enable */ +#define UART_IER_RTOIE 0x10 /* Receiver Time Out Interrupt Enable */ + +#define UART_IIR_TOD 0x08 /* Character Timeout Indication Detected */ + +#define UART_FCR_PXAR1 0x00 /* receive FIFO threshold = 1 */ +#define UART_FCR_PXAR8 0x40 /* receive FIFO threshold = 8 */ +#define UART_FCR_PXAR16 0x80 /* receive FIFO threshold = 16 */ +#define UART_FCR_PXAR32 0xc0 /* receive FIFO threshold = 32 */ + +/* + * Intel MID on-chip HSU (High Speed UART) defined bits + */ +#define UART_FCR_HSU_64_1B 0x00 /* receive FIFO treshold = 1 */ +#define UART_FCR_HSU_64_16B 0x40 /* receive FIFO treshold = 16 */ +#define UART_FCR_HSU_64_32B 0x80 /* receive FIFO treshold = 32 */ +#define UART_FCR_HSU_64_56B 0xc0 /* receive FIFO treshold = 56 */ + +#define UART_FCR_HSU_16_1B 0x00 /* receive FIFO treshold = 1 */ +#define UART_FCR_HSU_16_4B 0x40 /* receive FIFO treshold = 4 */ +#define UART_FCR_HSU_16_8B 0x80 /* receive FIFO treshold = 8 */ +#define UART_FCR_HSU_16_14B 0xc0 /* receive FIFO treshold = 14 */ + +#define UART_FCR_HSU_64B_FIFO 0x20 /* chose 64 bytes FIFO */ +#define UART_FCR_HSU_16B_FIFO 0x00 /* chose 16 bytes FIFO */ + +#define UART_FCR_HALF_EMPT_TXI 0x00 /* trigger TX_EMPT IRQ for half empty */ +#define UART_FCR_FULL_EMPT_TXI 0x08 /* trigger TX_EMPT IRQ for full empty */ + +/* + * These register definitions are for the 16C950 + */ +#define UART_ASR 0x01 /* Additional Status Register */ +#define UART_RFL 0x03 /* Receiver FIFO level */ +#define UART_TFL 0x04 /* Transmitter FIFO level */ +#define UART_ICR 0x05 /* Index Control Register */ + +/* The 16950 ICR registers */ +#define UART_ACR 0x00 /* Additional Control Register */ +#define UART_CPR 0x01 /* Clock Prescalar Register */ +#define UART_TCR 0x02 /* Times Clock Register */ +#define UART_CKS 0x03 /* Clock Select Register */ +#define UART_TTL 0x04 /* Transmitter Interrupt Trigger Level */ +#define UART_RTL 0x05 /* Receiver Interrupt Trigger Level */ +#define UART_FCL 0x06 /* Flow Control Level Lower */ +#define UART_FCH 0x07 /* Flow Control Level Higher */ +#define UART_ID1 0x08 /* ID #1 */ +#define UART_ID2 0x09 /* ID #2 */ +#define UART_ID3 0x0A /* ID #3 */ +#define UART_REV 0x0B /* Revision */ +#define UART_CSR 0x0C /* Channel Software Reset */ +#define UART_NMR 0x0D /* Nine-bit Mode Register */ +#define UART_CTR 0xFF + +/* + * The 16C950 Additional Control Register + */ +#define UART_ACR_RXDIS 0x01 /* Receiver disable */ +#define UART_ACR_TXDIS 0x02 /* Transmitter disable */ +#define UART_ACR_DSRFC 0x04 /* DSR Flow Control */ +#define UART_ACR_TLENB 0x20 /* 950 trigger levels enable */ +#define UART_ACR_ICRRD 0x40 /* ICR Read enable */ +#define UART_ACR_ASREN 0x80 /* Additional status enable */ + + + +/* + * These definitions are for the RSA-DV II/S card, from + * + * Kiyokazu SUTO <suto@ks-and-ks.ne.jp> + */ + +#define UART_RSA_BASE (-8) + +#define UART_RSA_MSR ((UART_RSA_BASE) + 0) /* I/O: Mode Select Register */ + +#define UART_RSA_MSR_SWAP (1 << 0) /* Swap low/high 8 bytes in I/O port addr */ +#define UART_RSA_MSR_FIFO (1 << 2) /* Enable the external FIFO */ +#define UART_RSA_MSR_FLOW (1 << 3) /* Enable the auto RTS/CTS flow control */ +#define UART_RSA_MSR_ITYP (1 << 4) /* Level (1) / Edge triger (0) */ + +#define UART_RSA_IER ((UART_RSA_BASE) + 1) /* I/O: Interrupt Enable Register */ + +#define UART_RSA_IER_Rx_FIFO_H (1 << 0) /* Enable Rx FIFO half full int. */ +#define UART_RSA_IER_Tx_FIFO_H (1 << 1) /* Enable Tx FIFO half full int. */ +#define UART_RSA_IER_Tx_FIFO_E (1 << 2) /* Enable Tx FIFO empty int. */ +#define UART_RSA_IER_Rx_TOUT (1 << 3) /* Enable char receive timeout int */ +#define UART_RSA_IER_TIMER (1 << 4) /* Enable timer interrupt */ + +#define UART_RSA_SRR ((UART_RSA_BASE) + 2) /* IN: Status Read Register */ + +#define UART_RSA_SRR_Tx_FIFO_NEMP (1 << 0) /* Tx FIFO is not empty (1) */ +#define UART_RSA_SRR_Tx_FIFO_NHFL (1 << 1) /* Tx FIFO is not half full (1) */ +#define UART_RSA_SRR_Tx_FIFO_NFUL (1 << 2) /* Tx FIFO is not full (1) */ +#define UART_RSA_SRR_Rx_FIFO_NEMP (1 << 3) /* Rx FIFO is not empty (1) */ +#define UART_RSA_SRR_Rx_FIFO_NHFL (1 << 4) /* Rx FIFO is not half full (1) */ +#define UART_RSA_SRR_Rx_FIFO_NFUL (1 << 5) /* Rx FIFO is not full (1) */ +#define UART_RSA_SRR_Rx_TOUT (1 << 6) /* Character reception timeout occurred (1) */ +#define UART_RSA_SRR_TIMER (1 << 7) /* Timer interrupt occurred */ + +#define UART_RSA_FRR ((UART_RSA_BASE) + 2) /* OUT: FIFO Reset Register */ + +#define UART_RSA_TIVSR ((UART_RSA_BASE) + 3) /* I/O: Timer Interval Value Set Register */ + +#define UART_RSA_TCR ((UART_RSA_BASE) + 4) /* OUT: Timer Control Register */ + +#define UART_RSA_TCR_SWITCH (1 << 0) /* Timer on */ + +/* + * The RSA DSV/II board has two fixed clock frequencies. One is the + * standard rate, and the other is 8 times faster. + */ +#define SERIAL_RSA_BAUD_BASE (921600) +#define SERIAL_RSA_BAUD_BASE_LO (SERIAL_RSA_BAUD_BASE / 8) + +/* + * Extra serial register definitions for the internal UARTs + * in TI OMAP processors. + */ +#define UART_OMAP_MDR1 0x08 /* Mode definition register */ +#define UART_OMAP_MDR2 0x09 /* Mode definition register 2 */ +#define UART_OMAP_SCR 0x10 /* Supplementary control register */ +#define UART_OMAP_SSR 0x11 /* Supplementary status register */ +#define UART_OMAP_EBLR 0x12 /* BOF length register */ +#define UART_OMAP_OSC_12M_SEL 0x13 /* OMAP1510 12MHz osc select */ +#define UART_OMAP_MVER 0x14 /* Module version register */ +#define UART_OMAP_SYSC 0x15 /* System configuration register */ +#define UART_OMAP_SYSS 0x16 /* System status register */ +#define UART_OMAP_WER 0x17 /* Wake-up enable register */ + +/* + * These are the definitions for the MDR1 register + */ +#define UART_OMAP_MDR1_16X_MODE 0x00 /* UART 16x mode */ +#define UART_OMAP_MDR1_SIR_MODE 0x01 /* SIR mode */ +#define UART_OMAP_MDR1_16X_ABAUD_MODE 0x02 /* UART 16x auto-baud */ +#define UART_OMAP_MDR1_13X_MODE 0x03 /* UART 13x mode */ +#define UART_OMAP_MDR1_MIR_MODE 0x04 /* MIR mode */ +#define UART_OMAP_MDR1_FIR_MODE 0x05 /* FIR mode */ +#define UART_OMAP_MDR1_CIR_MODE 0x06 /* CIR mode */ +#define UART_OMAP_MDR1_DISABLE 0x07 /* Disable (default state) */ + +/* + * These are definitions for the Exar XR17V35X and XR17(C|D)15X + */ +#define UART_EXAR_8XMODE 0x88 /* 8X sampling rate select */ +#define UART_EXAR_SLEEP 0x8b /* Sleep mode */ +#define UART_EXAR_DVID 0x8d /* Device identification */ + +#define UART_EXAR_FCTR 0x08 /* Feature Control Register */ +#define UART_FCTR_EXAR_IRDA 0x08 /* IrDa data encode select */ +#define UART_FCTR_EXAR_485 0x10 /* Auto 485 half duplex dir ctl */ +#define UART_FCTR_EXAR_TRGA 0x00 /* FIFO trigger table A */ +#define UART_FCTR_EXAR_TRGB 0x60 /* FIFO trigger table B */ +#define UART_FCTR_EXAR_TRGC 0x80 /* FIFO trigger table C */ +#define UART_FCTR_EXAR_TRGD 0xc0 /* FIFO trigger table D programmable */ + +#define UART_EXAR_TXTRG 0x0a /* Tx FIFO trigger level write-only */ +#define UART_EXAR_RXTRG 0x0b /* Rx FIFO trigger level write-only */ + +#endif /* _LINUX_SERIAL_REG_H */ + |
