Add support for V37 board

(patch by Jón Benediktsson, 11 Dec 2002)

4 files changed, 430 insertions, 20 deletions

diff --git a/include/commproc.h b/include/commproc.h
index 42db99897a..159c294f84 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -1100,6 +1100,34 @@ typedef struct scc_enet {
 #define SICR_ENET_CLKRT	((uint)0x00002e00)	/* RCLK-CLK2, TCLK-CLK3 */
 #endif	/* CONFIG_MHPC */
 
+/***  NETVIA  *******************************************************/
+
+#if defined(CONFIG_NETVIA)
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC2 use.
+ */
+#define	PROFF_ENET	PROFF_SCC2
+#define	CPM_CR_ENET	CPM_CR_CH_SCC2
+#define	SCC_ENET	1
+#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
+#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
+#define PA_ENET_RCLK	((ushort)0x0200)	/* PA  6 */
+#define PA_ENET_TCLK	((ushort)0x0800)	/* PA  4 */
+
+#define PB_ENET_PDN	((ushort)0x4000)	/* PB 17 */
+#define PB_ENET_TENA	((ushort)0x2000)	/* PB 18 */
+
+#define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
+#define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x0000ff00)
+#define SICR_ENET_CLKRT	((uint)0x00002f00)
+
+#endif	/* CONFIG_NETVIA */
+
 /***  RPXCLASSIC  *****************************************************/
 
 #ifdef CONFIG_RPXCLASSIC
@@ -1309,31 +1337,27 @@ typedef struct scc_enet {
 # endif	/* CONFIG_FEC_ENET */
 #endif	/* CONFIG_TQM860L, CONFIG_TQM855L */
 
-#if defined(CONFIG_NETVIA)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
+/***  V37  **********************************************************/
+
+#ifdef CONFIG_V37
+/* This ENET stuff is for the MPC823 with ethernet on SCC2.  Some of
+ * this may be unique to the Marel V37 configuration.
+ * Note TENA is on Port B.
  */
 #define	PROFF_ENET	PROFF_SCC2
 #define	CPM_CR_ENET	CPM_CR_CH_SCC2
 #define	SCC_ENET	1
-#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
-#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
-#define PA_ENET_RCLK	((ushort)0x0200)	/* PA  6 */
-#define PA_ENET_TCLK	((ushort)0x0800)	/* PA  4 */
-
-#define PB_ENET_PDN	((ushort)0x4000)	/* PB 17 */
-#define PB_ENET_TENA	((ushort)0x2000)	/* PB 18 */
-
-#define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
-#define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
+#define PA_ENET_RXD	((ushort)0x0004)
+#define PA_ENET_TXD	((ushort)0x0008)
+#define PA_ENET_TCLK	((ushort)0x0400)
+#define PA_ENET_RCLK	((ushort)0x0200)
+#define PB_ENET_TENA	((uint)0x00002000)
+#define PC_ENET_CLSN	((ushort)0x0040)
+#define PC_ENET_RENA	((ushort)0x0080)
 
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
 #define SICR_ENET_MASK	((uint)0x0000ff00)
-#define SICR_ENET_CLKRT	((uint)0x00002f00)
-
-#endif	/* CONFIG_NETVIA */
+#define SICR_ENET_CLKRT	((uint)0x00002e00)
+#endif	/* CONFIG_V37 */
 
 /*********************************************************************/
 
diff --git a/include/configs/v37.h b/include/configs/v37.h
new file mode 100644
index 0000000000..f5274404a9
--- /dev/null
+++ b/include/configs/v37.h
@@ -0,0 +1,381 @@
+/*
+ * (C) Copyright 2000, 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
+#define CONFIG_V37		1	/* ...on a Marel V37 board 	*/
+
+#define CONFIG_LCD
+#define CONFIG_SHARP_LQ084V1DG21
+#undef CONFIG_LCD_LOGO
+
+/*-----------------------------------------------------------------------------
+ * I2C Configuration
+ *-----------------------------------------------------------------------------
+ */
+#define CONFIG_I2C              1
+#define CFG_I2C_SLAVE           0x2
+
+#define	CONFIG_8xx_CONS_SMC1	1
+#undef	CONFIG_8xx_CONS_SMC2		/* Console is on SMC2		*/
+#undef	CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE		9600	/* console baudrate = 115kbps	*/
+#if 0
+#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
+#else
+#define CONFIG_BOOTDELAY	2	/* autoboot after 2 seconds	*/
+#endif
+
+#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+#define CONFIG_PREBOOT	"echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+
+#undef	CONFIG_BOOTARGS
+
+#define CONFIG_BOOTCOMMAND							\
+	"tftpboot; " 								\
+	"setenv bootargs console=tty0 "                                   \
+	"root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "		 	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " 	\
+	"bootm"
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#define	CONFIG_CAN_DRIVER	1	/* CAN Driver support enabled	*/
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
+
+#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
+				CFG_CMD_JFFS2	| \
+				CFG_CMD_DATE	)
+
+
+/* Flash banks JFFS2 should use */
+#define CFG_JFFS2_FIRST_BANK	1
+#define CFG_JFFS2_NUM_BANKS	1
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP			/* undef to save memory		*/
+#define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define	CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define	CFG_LOAD_ADDR		0x100000	/* default load address	*/
+
+#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR		0xF0000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
+#define	CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define	CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define	CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE0		0x40000000
+#define CFG_FLASH_BASE1		0x60000000
+#define CFG_FLASH_BASE		CFG_FLASH_BASE1
+
+#if defined(DEBUG)
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#else
+#define	CFG_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
+#endif
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE0
+#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	35	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define	CFG_ENV_IS_IN_NVRAM	1
+#define	CFG_ENV_ADDR		0x80000000/* Address of Environment */
+#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
+
+#define CFG_ENV_OFFSET		0
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control				11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR	0xFFFFFF88
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration				11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_FRC | SIUMCR_GB5E)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control				11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register		11-27
+ *-----------------------------------------------------------------------
+ */
+/*%%%#define CFG_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
+#define CFG_RTCSC	(RTCSC_SEC | RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+/*
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+*/
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit
+ *
+ * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
+ */
+/* up to 50 MHz we use a 1:1 clock */
+#define CFG_PLPRCR	( (1524 << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TMIST | PLPRCR_TEXPS )
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register		15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK	SCCR_EBDF11
+/* up to 50 MHz we use a 1:1 clock */
+#define CFG_SCCR	(SCCR_COM00 | SCCR_TBS)
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR	(0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR	(0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR	(0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR	(0xEC000000)
+#define CFG_PCMCIA_IO_SIZE	( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#undef	CONFIG_IDE_PCCARD		/* Use IDE with PC Card	Adapter	*/
+
+#undef	CONFIG_IDE_PCMCIA		/* Direct IDE    not supported	*/
+#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
+#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
+
+#define CFG_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
+#define CFG_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
+
+#define CFG_ATA_IDE0_OFFSET	0x0000
+
+#define CFG_ATA_BASE_ADDR	CFG_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O			*/
+#define CFG_ATA_DATA_OFFSET	(CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses	*/
+#define CFG_ATA_REG_OFFSET	(2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers	*/
+#define CFG_ATA_ALT_OFFSET	0x0100
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define	CFG_DER	0x0082000F
+/*#define CFG_DER	0*/
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0 and OR0 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
+#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #1	*/
+
+#define CFG_PRELIM_OR_AM	0xFE000000	/* OR addr mask */
+
+#define CFG_OR_TIMING_FLASH 	0xF56
+
+#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V)
+
+#define CFG_OR5_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR5_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V)
+
+/*
+ * BR1 and OR1 (Battery backed SRAM)
+ */
+#define	CFG_BR1_PRELIM	0x80000401
+#define CFG_OR1_PRELIM	0xFFC00736
+
+/*
+ * BR2 and OR2 (SDRAM)
+ */
+#define SDRAM_BASE_PRELIM	0x00000000	/* SDRAM base	*/
+#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB */
+
+#define CFG_OR_TIMING_SDRAM	0x00000A00
+
+#define CFG_OR2_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
+#define CFG_BR2_PRELIM	((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+/* Marel V37 mem setting */
+
+#define	CFG_BR3_CAN	0xC0000401
+#define CFG_OR3_CAN	0xFFFF0724
+
+/*
+#define	CFG_BR3_PRELIM	0xFA400001
+#define CFG_OR3_PRELIM	0xFFFF8910
+#define	CFG_BR4_PRELIM	0xFA000401
+#define CFG_OR4_PRELIM	0xFFFE0970
+*/
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTA	97		/* start with divider for 100 MHz	*/
+
+/*
+ * Refresh clock Prescalar
+ */
+#define CFG_MPTPR	MPTPR_PTP_DIV16
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 10 column SDRAM */
+#define CFG_MAMR_10COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
+			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 |	\
+			 MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+
+
+#endif	/* __CONFIG_H */
diff --git a/include/flash.h b/include/flash.h
index 3150e3dc34..b4c8bad3da 100644
--- a/include/flash.h
+++ b/include/flash.h
@@ -111,6 +111,7 @@ extern int flash_real_protect(flash_info_t *info, long sector, int prot);
 #define INTEL_MANUFACT	0x00890089	/* INTEL   manuf. ID in D23..D16, D7..D0 */
 #define	INTEL_ALT_MANU	0x00B000B0	/* alternate INTEL namufacturer ID	*/
 #define MX_MANUFACT	0x00C200C2	/* MXIC	   manuf. ID in D23..D16, D7..D0 */
+#define TOSH_MANUFACT	0x00980098	/* TOSHIBA manuf. ID in D23..D16, D7..D0 */
 
 					/* Micron Technologies (INTEL compat.)	*/
 #define MT_ID_28F400_T	0x44704470	/* 28F400B3 ID ( 4 M, top boot sector)	*/
@@ -206,6 +207,9 @@ extern int flash_real_protect(flash_info_t *info, long sector, int prot);
 #define SHARP_ID_28F008SC   0xA6A6A6A6	/* LH28F008SCT-L12 1Mx8, 16 64k blocks	*/
 					/* LH28F008SCR-L85 1Mx8, 16 64k blocks	*/
 
+#define TOSH_ID_FVT160	0xC2		/* TC58FVT160 ID (16 M, top )           */
+#define TOSH_ID_FVB160	0x43		/* TC58FVT160 ID (16 M, bottom )        */
+
 /*-----------------------------------------------------------------------
  * Internal FLASH identification codes
  *
@@ -301,6 +305,7 @@ extern int flash_real_protect(flash_info_t *info, long sector, int prot);
 #define FLASH_MAN_BM	0x00020000	/* Bright Microelectronics		*/
 #define FLASH_MAN_MX	0x00030000	/* MXIC					*/
 #define FLASH_MAN_STM	0x00040000
+#define FLASH_MAN_TOSH	0x00050000	/* Toshiba                		*/
 #define FLASH_MAN_SST	0x00100000
 #define FLASH_MAN_INTEL	0x00300000
 #define FLASH_MAN_MT	0x00400000
diff --git a/include/version.h b/include/version.h
index b501028bd5..5249f2a598 100644
--- a/include/version.h
+++ b/include/version.h
@@ -24,6 +24,6 @@
 #ifndef	__VERSION_H__
 #define	__VERSION_H__
 
-#define	U_BOOT_VERSION	"U-Boot 0.2.1"
+#define	U_BOOT_VERSION	"U-Boot 0.2.2"
 
 #endif	/* __VERSION_H__ */