ppc4xx: remove HH405 board

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>

1 files changed, 0 insertions, 479 deletions

diff --git a/include/configs/HH405.h b/include/configs/HH405.h
deleted file mode 100644
index 033dcbfe26..0000000000
--- a/include/configs/HH405.h
+++ /dev/null
@@ -1,479 +0,0 @@
-/*
- * (C) Copyright 2001-2004
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * (C) Copyright 2005
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * (C) Copyright 2006
- * Matthias Fuchs, esd GmbH, matthias.fuchs@esd-electronics.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_HH405		1	/* ...on a HH405 board	        */
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF80000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
-#define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
-
-#define CONFIG_SYS_CLK_FREQ     33333400 /* external frequency to pll   */
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_BAUDRATE		9600
-#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
-
-#undef	CONFIG_BOOTARGS
-#undef	CONFIG_BOOTCOMMAND
-
-#define CONFIG_PREBOOT	        "autoupd"
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"pciconfighost=1\0"						\
-	""
-
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_PPC4xx_EMAC
-#undef  CONFIG_HAS_ETH1
-
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_PHY_ADDR		0	/* PHY address			*/
-#define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
-#define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
-
-#define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
-
-/*
- * Video console
- */
-#define CONFIG_VIDEO			/* for sm501 video support	*/
-
-#ifdef CONFIG_VIDEO
-#define CONFIG_VIDEO_SM501
-#if 0
-#define CONFIG_VIDEO_SM501_32BPP
-#else
-#define CONFIG_VIDEO_SM501_16BPP
-#endif
-#define CONFIG_VIDEO_SM501_FBMEM_OFFSET 0x10000
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_CONSOLE_EXTRA_INFO
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_VIDEO_BMP_GZIP		/* gzip compressed bmp images	*/
-#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE	(2 << 20)	/* for decompressed img */
-
-#endif /* CONFIG_VIDEO */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_EEPROM
-
-#ifdef CONFIG_VIDEO
-#define CONFIG_CMD_BMP
-#endif
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_SUPPORT_VFAT
-
-#define CONFIG_AUTO_UPDATE      1       /* autoupdate via compactflash  */
-#undef CONFIG_AUTO_UPDATE_SHOW          /* use board show routine       */
-
-#undef  CONFIG_BZIP2	 /* include support for bzip2 compressed images */
-#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#undef	CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser	*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_DEVICE_NULLDEV      1       /* include nulldev device       */
-
-#undef  CONFIG_SYS_CONSOLE_INFO_QUIET          /* print console @ startup	*/
-
-#define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_CONS_INDEX	2	/* Use UART1			*/
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
-
-#undef  CONFIG_SYS_EXT_SERIAL_CLOCK           /* no external serial clock used */
-#define CONFIG_SYS_BASE_BAUD       691200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE      \
-	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
-	 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
-#define CONFIG_SYS_EXTBDINFO	1		/* To use extended board_into (bd_t) */
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-
-#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
-
-#define CONFIG_SYS_RX_ETH_BUFFER	16      /* use 16 rx buffer on 405 emac */
-
-/*-----------------------------------------------------------------------
- * RTC stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_RTC_DS1338
-#define CONFIG_SYS_I2C_RTC_ADDR	0x68
-
-/*-----------------------------------------------------------------------
- * NAND-FLASH stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
-#define NAND_BIG_DELAY_US	25
-
-#define CONFIG_SYS_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
-#define CONFIG_SYS_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
-#define CONFIG_SYS_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
-#define CONFIG_SYS_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
-
-#define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
-#define CONFIG_SYS_NAND_QUIET          1
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
-
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_HOST	PCI_HOST_HOST   /* select pci host function     */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
-
-#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
-
-#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
-#define CONFIG_SYS_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
-#define CONFIG_SYS_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CONFIG_SYS_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CONFIG_SYS_PCI_PTM2LA  0xffc00000      /* point to flash               */
-#define CONFIG_SYS_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CONFIG_SYS_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff
- *-----------------------------------------------------------------------
- */
-#undef  CONFIG_IDE_8xx_DIRECT               /* no pcmcia interface required */
-#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
-#define CONFIG_IDE_RESET	1	/* reset for ide supported	*/
-
-#define	CONFIG_SYS_IDE_MAXBUS	        1		/* max. 1 IDE busses	*/
-#define	CONFIG_SYS_IDE_MAXDEVICE	(CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-
-#define	CONFIG_SYS_ATA_BASE_ADDR	0xF0100000
-#define	CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O			*/
-#define	CONFIG_SYS_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define FLASH_BASE0_PRELIM	0xFFC00000	/* FLASH bank #0	*/
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
-
-#define CONFIG_SYS_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CONFIG_SYS_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CONFIG_SYS_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
-/*
- * The following defines are added for buggy IOP480 byte interface.
- * All other boards should use the standard values (CPCI405 etc.)
- */
-#define CONFIG_SYS_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CONFIG_SYS_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CONFIG_SYS_FLASH_READ2         0x0002  /* 2 is standard                        */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
-
-#if 0 /* test-only */
-#define CONFIG_SYS_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
-#define CONFIG_SYS_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
-#endif
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0xFFF80000
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(4 << 20)	/* Reserve 4 MB for malloc()	*/
-
-#if (CONFIG_SYS_MONITOR_BASE < FLASH_BASE0_PRELIM)
-# define CONFIG_SYS_RAMBOOT		1
-#else
-# undef CONFIG_SYS_RAMBOOT
-#endif
-
-/*-----------------------------------------------------------------------
- * Environment Variable setup
- */
-#define CONFIG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET          0x100   /* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_SIZE            0x700   /* 2048 bytes may be used for env vars*/
-				   /* total size of a CAT24WC16 is 2048 bytes */
-
-#define CONFIG_SYS_NVRAM_BASE_ADDR	0xF4080000		/* NVRAM base address	*/
-#define CONFIG_SYS_NVRAM_SIZE		0x8000		        /* NVRAM size		*/
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC16) for environment
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#if 0 /* test-only */
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
-#else
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
-#endif
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
-#define CONFIG_SYS_EEPROM_WREN         1
-
-#if 1 /* test-only */
-/* CAT24WC08/16... */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
-					/* 16 byte page write mode using*/
-					/* last	4 bits of the address	*/
-#else
-/* CAT24WC32/64... */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x01
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5	/* The Catalyst CAT24WC32 has	*/
-					/* 32 byte page write mode using*/
-					/* last	5 bits of the address	*/
-#endif
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-#define CAN_BA          0xF0000000          /* CAN Base Address                 */
-#define LCD_BA          0xF1000000          /* Epson LCD Base Address           */
-#define CONFIG_SYS_NAND_BASE   0xF4000000          /* NAND FLASH Base Address          */
-#define CONFIG_SYS_NVRAM_BASE  0xF4080000          /* NVRAM Base Address               */
-
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization                       */
-#define CONFIG_SYS_EBC_PB0AP           0x92015480
-#define CONFIG_SYS_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 1 (Flash Bank 1, NAND-FLASH & NVRAM) initialization              */
-#define CONFIG_SYS_EBC_PB1AP           0x92015480
-#define CONFIG_SYS_EBC_PB1CR           0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit  */
-
-/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization              */
-#define CONFIG_SYS_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
-
-/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization     */
-#define CONFIG_SYS_EBC_PB3AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB3CR           0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 4 (Epson LCD) initialization                                     */
-#define CONFIG_SYS_EBC_PB4AP   0x03805380   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=0 */
-#define CONFIG_SYS_EBC_PB4CR   LCD_BA | 0x7A000    /* BAS=0xF10,BS=8MB,BU=R/W,BW=16bit */
-
-/*-----------------------------------------------------------------------
- * LCD Setup
- */
-
-#define CONFIG_SYS_LCD_BIG_MEM         0xF1200000  /* Epson S1D13806 Mem Base Address  */
-#define CONFIG_SYS_LCD_BIG_REG         0xF1000000  /* Epson S1D13806 Reg Base Address  */
-#define CONFIG_SYS_LCD_SMALL_MEM       0xF1400000  /* Epson S1D13704 Mem Base Address  */
-#define CONFIG_SYS_LCD_SMALL_REG       0xF140FFE0  /* Epson S1D13704 Reg Base Address  */
-
-/*-----------------------------------------------------------------------
- * Universal Interrupt Controller (UIC) Setup
- */
-
-/*
- * define UIC_EXT0 ... UIC_EXT6 if external interrupt is active high
- */
-#define CONFIG_SYS_UIC0_POLARITY       (0xFFFFFF80 | UIC_MASK(VECNUM_EIRQ6))
-
-/*-----------------------------------------------------------------------
- * FPGA stuff
- */
-
-#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100       /* FPGA internal Base Address       */
-
-#define LCD_CLK_OFF             0x0000      /* Off                           */
-#define LCD_CLK_02083           0x1000      /* 2.083 MHz                     */
-#define LCD_CLK_03135           0x2000      /* 3.135 MHz                     */
-#define LCD_CLK_04165           0x3000      /* 4.165 MHz                     */
-#define LCD_CLK_06250           0x4000      /* 6.250 MHz                     */
-#define LCD_CLK_08330           0x5000      /* 8.330 MHz                     */
-#define LCD_CLK_12500           0x6000      /* 12.50 MHz                     */
-#define LCD_CLK_25000           0x7000      /* 25.00 MHz                     */
-
-#define CONFIG_SYS_FPGA_SPARTAN2       1           /* using Xilinx Spartan 2 now    */
-#define CONFIG_SYS_FPGA_MAX_SIZE       128*1024    /* 128kByte is enough for XC2S50E*/
-
-/* FPGA program pin configuration */
-#define CONFIG_SYS_FPGA_PRG            0x04000000  /* FPGA program pin (ppc output) */
-#define CONFIG_SYS_FPGA_CLK            0x02000000  /* FPGA clk pin (ppc output)     */
-#define CONFIG_SYS_FPGA_DATA           0x01000000  /* FPGA data pin (ppc output)    */
-#define CONFIG_SYS_FPGA_INIT           0x00010000  /* FPGA init pin (ppc input)     */
-#define CONFIG_SYS_FPGA_DONE           0x00008000  /* FPGA done pin (ppc input)     */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CONFIG_SYS_TEMP_STACK_OCM        1
-
-/* On Chip Memory location */
-#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
-#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EP specific)
- *
- * GPIO0[0]     - External Bus Controller BLAST output
- * GPIO0[1-9]   - Instruction trace outputs -> GPIO
- * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
- * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
- * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
- * GPIO0[24-27] - UART0 control signal inputs/outputs
- * GPIO0[28-29] - UART1 data signal input/output
- * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
- */
-#define CONFIG_SYS_GPIO0_OSRL		0x40000550
-#define CONFIG_SYS_GPIO0_OSRH		0x00000110
-#define CONFIG_SYS_GPIO0_ISR1L		0x00000000
-#define CONFIG_SYS_GPIO0_ISR1H		0x15555440
-#define CONFIG_SYS_GPIO0_TSRL		0x00000000
-#define CONFIG_SYS_GPIO0_TSRH		0x00000000
-#define CONFIG_SYS_GPIO0_TCR		0xF7FE0017
-
-#define CONFIG_SYS_LCD_ENDIAN		(0x80000000 >> 7)
-#define CONFIG_SYS_EEPROM_WP		(0x80000000 >> 8)   /* GPIO8 */
-#define CONFIG_SYS_TOUCH_RST		(0x80000000 >> 9)   /* GPIO9 */
-#define CONFIG_SYS_LCD0_RST		(0x80000000 >> 30)
-#define CONFIG_SYS_LCD1_RST		(0x80000000 >> 31)
-
-/*
- * Default speed selection (cpu_plb_opb_ebc) in mhz.
- * This value will be set if iic boot eprom is disabled.
- */
-#if 0
-#define PLLMR0_DEFAULT   PLLMR0_266_133_66_33
-#define PLLMR1_DEFAULT   PLLMR1_266_133_66_33
-#endif
-#if 0
-#define PLLMR0_DEFAULT   PLLMR0_200_100_50_33
-#define PLLMR1_DEFAULT   PLLMR1_200_100_50_33
-#endif
-#if 1
-#define PLLMR0_DEFAULT   PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT   PLLMR1_133_66_66_33
-#endif
-
-#endif	/* __CONFIG_H */