powerpc/p1010rdb: update readme for p1010rdb-pa and p1010rdb-pb

- Remove duplicate doc/README.p1010rdb
- Rename README to README.P1010RDB-PA
- Add new README.P1010RDB-PB

P1010RDB-PB is a variation of previous P1010RDB-PA board.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>

1 files changed, 0 insertions, 198 deletions

diff --git a/doc/README.p1010rdb b/doc/README.p1010rdb
deleted file mode 100644
index 6b2b5ff3fb..0000000000
--- a/doc/README.p1010rdb
+++ /dev/null
@@ -1,198 +0,0 @@
-Overview
-=========
-The P1010RDB is a Freescale reference design board that hosts the P1010 SoC.
-
-The P1010 is a cost-effective, low-power, highly integrated host processor
-based on a Power Architecture e500v2 core (maximum core frequency 800/1000 MHz),
-that addresses the requirements of several routing, gateways, storage, consumer,
-and industrial applications. Applications of interest include the main CPUs and
-I/O processors in network attached storage (NAS), the voice over IP (VoIP)
-router/gateway, and wireless LAN (WLAN) and industrial controllers.
-
-The P1010RDB board features are as follows:
-Memory subsystem:
-	- 1Gbyte unbuffered DDR3 SDRAM discrete devices (32-bit bus)
-	- 32 Mbyte NOR flash single-chip memory
-	- 32 Mbyte NAND flash memory
-	- 256 Kbit M24256 I2C EEPROM
-	- 16 Mbyte SPI memory
-	- I2C Board EEPROM 128x8 bit memory
-	- SD/MMC connector to interface with the SD memory card
-Interfaces:
-	- PCIe:
-		- Lane0: x1 mini-PCIe slot
-		- Lane1: x1 PCIe standard slot
-	- SATA:
-		- 1 internal SATA connector to 2.5" 160G SATA2 HDD
-		- 1 eSATA connector to rear panel
-	- 10/100/1000 BaseT Ethernet ports:
-		- eTSEC1, RGMII: one 10/100/1000 port using Vitesse VSC8641XKO
-		- eTSEC2, SGMII: one 10/100/1000 port using Vitesse VSC8221
-		- eTSEC3, SGMII: one 10/100/1000 port using Vitesse VSC8221
-	- USB 2.0 port:
-		- x1 USB2.0 port: via an ULPI PHY to micro-AB connector
-		- x1 USB2.0 poort via an internal PHY to micro-AB connector
-	- FlexCAN ports:
-		- x2 DB-9 female connectors for FlexCAN bus(revision 2.0B)
-		   interface;
-	- DUART interface:
-		- DUART interface: supports two UARTs up to 115200 bps for
-		  console display
-		- J45 connectors are used for these 2 UART ports.
-	- TDM
-		- 2 FXS ports connected via an external SLIC to the TDM
-		   interface. SLIC is controllled via SPI.
-		- 1 FXO port connected via a relay to FXS for switchover to
-		   POTS
-Board connectors:
-	- Mini-ITX power supply connector
-	- JTAG/COP for debugging
-IEEE Std. 1588 signals for test and measurement
-Real-time clock on I2C bus
-POR
-	- support critical POR setting changed via switch on board
-PCB
-	- 6-layer routing (4-layer signals, 2-layer power and ground)
-
-
-Serial Port Configuration on P1010RDB
-=====================================
-Configure the serial port of the attached computer with the following values:
-	-Data rate: 115200 bps
-	-Number of data bits: 8
-	-Parity: None
-	-Number of Stop bits: 1
-	-Flow Control: Hardware/None
-
-
-Settings of DIP-switch
-======================
-  SW4[1:4]= 1111 and SW6[4]=0 for boot from 16bit NOR flash
-  SW4[1:4]= 1000 and SW6[4]=1 for boot from 8bit NAND flash
-  SW4[1:4]= 0110 and SW6[4]=0 for boot from SPI flash
-Note: 1 stands for 'on', 0 stands for 'off'
-
-
-Setting of hwconfig
-===================
-If FlexCAN or TDM is needed, please set "fsl_p1010mux:tdm_can=can" or
-"fsl_p1010mux:tdm_can=tdm" explicitly in u-booot prompt as below for example:
-setenv hwconfig "fsl_p1010mux:tdm_can=tdm;usb1:dr_mode=host,phy_type=utmi"
-By default, don't set fsl_p1010mux:tdm_can, in this case, spi chip selection
-is set to spi-flash instead of to SLIC/TDM/DAC and tdm_can_sel is set to TDM
-instead of to CAN/UART1.
-
-
-Build and burn u-boot to NOR flash
-==================================
-1. Build u-boot.bin image
-	export ARCH=powerpc
-	export CROSS_COMPILE=/your_path/powerpc-linux-gnu-
-	make P1010RDB_NOR
-
-2. Burn u-boot.bin into NOR flash
-	=> tftp $loadaddr $uboot
-	=> protect off eff80000 +$filesize
-	=> erase eff80000 +$filesize
-	=> cp.b $loadaddr eff80000 $filesize
-
-3. Check SW4[1:4]= 1111 and SW6[4]=0, then power on.
-
-
-Alternate NOR bank
-============================
-1. Burn u-boot.bin into alternate NOR bank
-	=> tftp $loadaddr $uboot
-	=> protect off eef80000 +$filesize
-	=> erase eef80000 +$filesize
-	=> cp.b $loadaddr eef80000 $filesize
-
-2. Switch to alternate NOR bank
-	=> mw.b ffb00009 1
-	=> reset
-	or set SW1[8]= ON
-
-SW1[8]= OFF: Upper bank used for booting start
-SW1[8]= ON:  Lower bank used for booting start
-CPLD NOR bank selection register address 0xFFB00009 Bit[0]:
-0 - boot from upper 4 sectors
-1 - boot from lower 4 sectors
-
-
-Build and burn u-boot to NAND flash
-===================================
-1. Build u-boot.bin image
-	export ARCH=powerpc
-	export CROSS_COMPILE=/your_path/powerpc-linux-gnu-
-	make P1010RDB_NAND
-
-2. Burn u-boot-nand.bin into NAND flash
-	=> tftp $loadaddr $uboot-nand
-	=> nand erase 0 $filesize
-	=> nand write $loadaddr 0 $filesize
-
-3. Check SW4[1:4]= 1000 and SW6[4]=1, then power on.
-
-
-
-Build and burn u-boot to SPI flash
-==================================
-1. Build u-boot-spi.bin image
-	make P1010RDB_SPIFLASH_config; make
-	Boot up kernel with rootfs.ext2.gz.uboot.p1010rdb
-	Download u-boot.bin to linux and you can find some config files
-	under /usr/share such as config_xx.dat. Do below command:
-	boot_format config_ddr3_1gb_p1010rdb_800M.dat u-boot.bin -spi \
-			u-boot-spi.bin
-	to generate u-boot-spi.bin.
-
-2. Burn u-boot-spi.bin into SPI flash
-	=> tftp $loadaddr $uboot-spi
-	=> sf erase 0 100000
-	=> sf write $loadaddr 0 $filesize
-
-3. Check SW4[1:4]= 0110 and SW6[4]=0, then power on.
-
-
-
-CPLD POR setting registers
-==========================
-1. Set POR switch selection register (addr 0xFFB00011) to 0.
-2. Write CPLD POR registers (BCSR0~BCSR3, addr 0xFFB00014~0xFFB00017) with
-   proper values.
-   If change boot ROM location to NOR or NAND flash, need write the IFC_CS0
-   switch command by I2C.
-3. Send reset command.
-   After reset, the new POR setting will be implemented.
-
-Two examples are given in below:
-Switch from NOR to NAND boot with default frequency:
-	=> i2c dev 0
-	=> i2c mw 18 1 f9
-	=> i2c mw 18 3 f0
-	=> mw.b ffb00011 0
-	=> mw.b ffb00017 1
-	=> reset
-Switch from NAND to NOR boot with Core/CCB/DDR (800/400/667 MHz):
-	=> i2c dev 0
-	=> i2c mw 18 1 f1
-	=> i2c mw 18 3 f0
-	=> mw.b ffb00011 0
-	=> mw.b ffb00014 2
-	=> mw.b ffb00015 5
-	=> mw.b ffb00016 3
-	=> mw.b ffb00017 f
-	=> reset
-
-
-Boot Linux from network using TFTP on P1010RDB
-==============================================
-Place uImage, p1010rdb.dtb and rootfs files in the TFTP disk area.
-	=> tftp 1000000 uImage
-	=> tftp 2000000 p1010rdb.dtb
-	=> tftp 3000000 rootfs.ext2.gz.uboot.p1010rdb
-	=> bootm 1000000 3000000 2000000
-
-
-Please contact your local field applications engineer or sales representative
-to obtain related documents, such as P1010-RDB User Guide for details.