powerpc/8xxx: Add support for interactive DDR programming interface

Interactive DDR debugging provides a user interface to view and modify SPD,
DIMM parameters, board options and DDR controller registers before DDR is
initialized. With this feature, developers can fine-tune DDR for board
bringup and other debugging without frequently having to reprogram the flash.

To enable this feature, define CONFIG_FSL_DDR_INTERACTIVE in board header
file and set an environment variable to activate it. Syntax:

setenv ddr_interactive on

After reset, U-boot prompts before initializing DDR controllers
FSL DDR>

The available commands are
print      print SPD and intermediate computed data
reset      reboot machine
recompute  reload SPD and options to default and recompute regs
edit       modify spd, parameter, or option
compute    recompute registers from current next_step to end
next_step  shows current next_step
help       this message
go         program the memory controller and continue with u-boot

The first command should be "compute", which reads data from DIMM SPDs and
board options, performs the calculation then stops before setting DDR
controller. A user can use "print" and "edit" commands to view and modify
anything. "Go" picks up from current step with any modification and
compltes the calculation then enables the DDR controller to continue u-boot.
"Recompute" does it over from fresh reading.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

1 files changed, 150 insertions, 0 deletions

diff --git a/doc/README.fsl-ddr b/doc/README.fsl-ddr
index abfb7f192d..1d50153d58 100644
--- a/doc/README.fsl-ddr
+++ b/doc/README.fsl-ddr
@@ -222,3 +222,153 @@ Single slot system
 
 Reference http://www.samsung.com/global/business/semiconductor/products/dram/downloads/applicationnote/ddr2_odt_control_200603.pdf
 
+
+Interactive DDR debugging
+===========================
+
+For DDR parameter tuning up and debugging, the interactive DDR debugging can
+be activated by saving an environment variable "ddr_interactive". The value
+doesn't matter. Once activated, U-boot prompts "FSL DDR>" before enabling DDR
+controller. The available commands can be seen by typing "help".
+
+The example flow of using interactive debugging is
+type command "compute" to calculate the parameters from the default
+type command "print" with arguments to show SPD, options, registers
+type command "edit" with arguments to change any if desired
+type command "go" to continue calculation and enable DDR controller
+type command "reset" to reset the board
+type command "recompute" to reload SPD and start over
+
+Note, check "next_step" to show the flow. For example, after edit opts, the
+next_step is STEP_ASSIGN_ADDRESSES. After editing registers, the next_step is
+STEP_PROGRAM_REGS. Upon issuing command "go", DDR controller will be enabled
+with current setting without further calculation.
+
+The detail syntax for each commands are
+
+print [c<n>] [d<n>] [spd] [dimmparms] [commonparms] [opts] [addresses] [regs]
+	c<n>		- the controller number, eg. c0, c1
+	d<n>		- the DIMM number, eg. d0, d1
+	spd		- print SPD data
+	dimmparms	- DIMM paramaters, calcualted from SPD
+	commonparms	- lowest common parameters for all DIMMs
+	opts		- options
+	addresses	- address assignment (not implemented yet)
+	regs		- controller registers
+
+edit <c#> <d#> <spd|dimmparms|commonparms|opts|addresses|regs> <element> <value>
+	c<n>		- the controller number, eg. c0, c1
+	d<n>		- the DIMM number, eg. d0, d1
+	spd		- print SPD data
+	dimmparms	- DIMM paramaters, calcualted from SPD
+	commonparms	- lowest common parameters for all DIMMs
+	opts		- options
+	addresses	- address assignment (not implemented yet)
+	regs		- controller registers
+	<element>	- name of the modified element
+			  byte number if the object is SPD
+	<value>		- decimal or heximal (prefixed with 0x) numbers
+
+reset
+	no arguement	- reset the board
+
+recompute
+	no argument	- reload SPD and start over
+
+compute
+	no argument	- recompute from current next_step
+
+next_step
+	no argument	- show current next_step
+
+help
+	no argument	- print a list of all commands
+
+go
+	no argument	- program memory controller(s) and continue with U-boot
+
+Examples of debugging flow
+
+	FSL DDR>compute
+	Detected UDIMM UG51U6400N8SU-ACF
+	SL DDR>print
+	print [c<n>] [d<n>] [spd] [dimmparms] [commonparms] [opts] [addresses] [regs]
+	FSL DDR>print dimmparms
+	DIMM parameters:  Controller=0 DIMM=0
+	DIMM organization parameters:
+	module part name = UG51U6400N8SU-ACF
+	rank_density = 2147483648 bytes (2048 megabytes)
+	capacity = 4294967296 bytes (4096 megabytes)
+	burst_lengths_bitmask = 0C
+	base_addresss = 0 (00000000 00000000)
+	n_ranks = 2
+	data_width = 64
+	primary_sdram_width = 64
+	ec_sdram_width = 0
+	registered_dimm = 0
+	n_row_addr = 15
+	n_col_addr = 10
+	edc_config = 0
+	n_banks_per_sdram_device = 8
+	tCKmin_X_ps = 1500
+	tCKmin_X_minus_1_ps = 0
+	tCKmin_X_minus_2_ps = 0
+	tCKmax_ps = 0
+	caslat_X = 960
+	tAA_ps = 13125
+	caslat_X_minus_1 = 0
+	caslat_X_minus_2 = 0
+	caslat_lowest_derated = 0
+	tRCD_ps = 13125
+	tRP_ps = 13125
+	tRAS_ps = 36000
+	tWR_ps = 15000
+	tWTR_ps = 7500
+	tRFC_ps = 160000
+	tRRD_ps = 6000
+	tRC_ps = 49125
+	refresh_rate_ps = 7800000
+	tIS_ps = 0
+	tIH_ps = 0
+	tDS_ps = 0
+	tDH_ps = 0
+	tRTP_ps = 7500
+	tDQSQ_max_ps = 0
+	tQHS_ps = 0
+	FSL DDR>edit c0 opts ECC_mode 0
+	FSL DDR>edit c0 regs cs0_bnds 0x000000FF
+	FSL DDR>go
+	2 GiB left unmapped
+	4 GiB (DDR3, 64-bit, CL=9, ECC off)
+	       DDR Chip-Select Interleaving Mode: CS0+CS1
+	Testing 0x00000000 - 0x7fffffff
+	Testing 0x80000000 - 0xffffffff
+	Remap DDR 2 GiB left unmapped
+
+	POST memory PASSED
+	Flash: 128 MiB
+	L2:    128 KB enabled
+	Corenet Platform Cache: 1024 KB enabled
+	SERDES: timeout resetting bank 3
+	SRIO1: disabled
+	SRIO2: disabled
+	MMC:  FSL_ESDHC: 0
+	EEPROM: Invalid ID (ff ff ff ff)
+	PCIe1: disabled
+	PCIe2: Root Complex, x1, regs @ 0xfe201000
+	  01:00.0     - 8086:10d3 - Network controller
+	PCIe2: Bus 00 - 01
+	PCIe3: disabled
+	In:    serial
+	Out:   serial
+	Err:   serial
+	Net:   Initializing Fman
+	Fman1: Uploading microcode version 101.8.0
+	e1000: 00:1b:21:81:d2:e0
+	FM1@DTSEC1, FM1@DTSEC2, FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5, e1000#0 [PRIME]
+	Warning: e1000#0 MAC addresses don't match:
+	Address in SROM is         00:1b:21:81:d2:e0
+	Address in environment is  00:e0:0c:00:ea:05
+
+	Hit any key to stop autoboot:  0
+	=>