Merge branch 'master' into hpc2

11 files changed, 420 insertions, 733 deletions

diff --git a/board/amcc/yellowstone/init.S b/board/amcc/yellowstone/init.S
deleted file mode 100644
index 425ad0868f..0000000000
--- a/board/amcc/yellowstone/init.S
+++ /dev/null
@@ -1,112 +0,0 @@
-/*
-*
-* See file CREDITS for list of people who contributed to this
-* project.
-*
-* This program is free software; you can redistribute it and/or
-* modify it under the terms of the GNU General Public License as
-* published by the Free Software Foundation; either version 2 of
-* the License, or (at your option) any later version.
-*
-* This program is distributed in the hope that it will be useful,
-* but WITHOUT ANY WARRANTY; without even the implied warranty of
-* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
-* GNU General Public License for more details.
-*
-* You should have received a copy of the GNU General Public License
-* along with this program; if not, write to the Free Software
-* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-* MA 02111-1307 USA
-*/
-
-#include <ppc_asm.tmpl>
-#include <config.h>
-
-/* General */
-#define TLB_VALID   0x00000200
-
-/* Supported page sizes */
-
-#define SZ_1K	    0x00000000
-#define SZ_4K	    0x00000010
-#define SZ_16K	    0x00000020
-#define SZ_64K	    0x00000030
-#define SZ_256K	    0x00000040
-#define SZ_1M	    0x00000050
-#define SZ_8M       0x00000060
-#define SZ_16M	    0x00000070
-#define SZ_256M	    0x00000090
-
-/* Storage attributes */
-#define SA_W	    0x00000800	    /* Write-through */
-#define SA_I	    0x00000400	    /* Caching inhibited */
-#define SA_M	    0x00000200	    /* Memory coherence */
-#define SA_G	    0x00000100	    /* Guarded */
-#define SA_E	    0x00000080	    /* Endian */
-
-/* Access control */
-#define AC_X	    0x00000024	    /* Execute */
-#define AC_W	    0x00000012	    /* Write */
-#define AC_R	    0x00000009	    /* Read */
-
-/* Some handy macros */
-
-#define EPN(e)		((e) & 0xfffffc00)
-#define TLB0(epn,sz)	( (EPN((epn)) | (sz) | TLB_VALID ) )
-#define TLB1(rpn,erpn)	( ((rpn)&0xfffffc00) | (erpn) )
-#define TLB2(a)		( (a)&0x00000fbf )
-
-#define tlbtab_start\
-	mflr    r1  ;\
-	bl 0f	    ;
-
-#define tlbtab_end\
-	.long 0, 0, 0	;   \
-0:	mflr    r0	;   \
-	mtlr    r1	;   \
-	blr		;
-
-#define tlbentry(epn,sz,rpn,erpn,attr)\
-	.long TLB0(epn,sz),TLB1(rpn,erpn),TLB2(attr)
-
-
-/**************************************************************************
- * TLB TABLE
- *
- * This table is used by the cpu boot code to setup the initial tlb
- * entries. Rather than make broad assumptions in the cpu source tree,
- * this table lets each board set things up however they like.
- *
- *  Pointer to the table is returned in r1
- *
- *************************************************************************/
-
-    .section .bootpg,"ax"
-    .globl tlbtab
-
-tlbtab:
-    tlbtab_start
-
-    /*
-     * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
-     * speed up boot process. It is patched after relocation to enable SA_I
-     */
-    tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/)
-
-    /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
-    tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G )
-
-    tlbentry( CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
-    tlbentry( CFG_PCI_BASE, SZ_256M, CFG_PCI_BASE, 0, AC_R|AC_W|SA_G|SA_I )
-    tlbentry( CFG_NVRAM_BASE_ADDR, SZ_256M, CFG_NVRAM_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_W|SA_I )
-
-    /* PCI */
-    tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 0, AC_R|AC_W|SA_G|SA_I )
-    tlbentry( CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 0, AC_R|AC_W|SA_G|SA_I )
-    tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 0, AC_R|AC_W|SA_G|SA_I )
-    tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 0, AC_R|AC_W|SA_G|SA_I )
-
-    /* USB 2.0 Device */
-    tlbentry( CFG_USB_DEVICE, SZ_1K, 0x50000000, 0, AC_R|AC_W|SA_G|SA_I )
-
-    tlbtab_end
diff --git a/board/amcc/yellowstone/yellowstone.c b/board/amcc/yellowstone/yellowstone.c
deleted file mode 100644
index 04f58e0419..0000000000
--- a/board/amcc/yellowstone/yellowstone.c
+++ /dev/null
@@ -1,549 +0,0 @@
-/*
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <ppc4xx.h>
-#include <asm/processor.h>
-#include <spd_sdram.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
-
-int board_early_init_f(void)
-{
-	register uint reg;
-
-	/*--------------------------------------------------------------------
-	 * Setup the external bus controller/chip selects
-	 *-------------------------------------------------------------------*/
-	mtdcr(ebccfga, xbcfg);
-	reg = mfdcr(ebccfgd);
-	mtdcr(ebccfgd, reg | 0x04000000);	/* Set ATC */
-
-	/*--------------------------------------------------------------------
-	 * Setup the GPIO pins
-	 *-------------------------------------------------------------------*/
-	/*CPLD cs */
-	/*setup Address lines for flash size 64Meg. */
-	out32(GPIO0_OSRL, in32(GPIO0_OSRL) | 0x50010000);
-	out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x50010000);
-	out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x50000000);
-
-	/*setup emac */
-	out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xC080);
-	out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x40);
-	out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x55);
-	out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0x50004000);
-	out32(GPIO0_ISR1H, in32(GPIO0_ISR1H) | 0x00440000);
-
-	/*UART1 */
-	out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x02000000);
-	out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x00080000);
-	out32(GPIO1_ISR2L, in32(GPIO1_ISR2L) | 0x00010000);
-
-	/* external interrupts IRQ0...3 */
-	out32(GPIO1_TCR, in32(GPIO1_TCR) & ~0x00f00000);
-	out32(GPIO1_TSRL, in32(GPIO1_TSRL) & ~0x0000ff00);
-	out32(GPIO1_ISR1L, in32(GPIO1_ISR1L) | 0x00005500);
-
-#if 0 /* test-only */
-	/*setup USB 2.0 */
-	out32(GPIO1_TCR, in32(GPIO1_TCR) | 0xc0000000);
-	out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x50000000);
-	out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xf);
-	out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0xaa);
-	out32(GPIO0_ISR2H, in32(GPIO0_ISR2H) | 0x00000500);
-#endif
-
-	/*--------------------------------------------------------------------
-	 * Setup the interrupt controller polarities, triggers, etc.
-	 *-------------------------------------------------------------------*/
-	mtdcr(uic0sr, 0xffffffff);	/* clear all */
-	mtdcr(uic0er, 0x00000000);	/* disable all */
-	mtdcr(uic0cr, 0x00000009);	/* ATI & UIC1 crit are critical */
-	mtdcr(uic0pr, 0xfffffe13);	/* per ref-board manual */
-	mtdcr(uic0tr, 0x01c00008);	/* per ref-board manual */
-	mtdcr(uic0vr, 0x00000001);	/* int31 highest, base=0x000 */
-	mtdcr(uic0sr, 0xffffffff);	/* clear all */
-
-	mtdcr(uic1sr, 0xffffffff);	/* clear all */
-	mtdcr(uic1er, 0x00000000);	/* disable all */
-	mtdcr(uic1cr, 0x00000000);	/* all non-critical */
-	mtdcr(uic1pr, 0xffffe0ff);	/* per ref-board manual */
-	mtdcr(uic1tr, 0x00ffc000);	/* per ref-board manual */
-	mtdcr(uic1vr, 0x00000001);	/* int31 highest, base=0x000 */
-	mtdcr(uic1sr, 0xffffffff);	/* clear all */
-
-	/*--------------------------------------------------------------------
-	 * Setup other serial configuration
-	 *-------------------------------------------------------------------*/
-	mfsdr(sdr_pci0, reg);
-	mtsdr(sdr_pci0, 0x80000000 | reg);	/* PCI arbiter enabled */
-	mtsdr(sdr_pfc0, 0x00003e00);	/* Pin function */
-	mtsdr(sdr_pfc1, 0x00048000);	/* Pin function: UART0 has 4 pins */
-
-	/*clear tmrclk divisor */
-	*(unsigned char *)(CFG_BCSR_BASE | 0x04) = 0x00;
-
-	/*enable ethernet */
-	*(unsigned char *)(CFG_BCSR_BASE | 0x08) = 0xf0;
-
-#if 0 /* test-only */
-	/*enable usb 1.1 fs device and remove usb 2.0 reset */
-	*(unsigned char *)(CFG_BCSR_BASE | 0x09) = 0x00;
-#endif
-
-	/*get rid of flash write protect */
-	*(unsigned char *)(CFG_BCSR_BASE | 0x07) = 0x00;
-
-	return 0;
-}
-
-int misc_init_r (void)
-{
-	uint pbcr;
-	int size_val = 0;
-
-	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
-	pbcr = mfdcr(ebccfgd);
-	switch (gd->bd->bi_flashsize) {
-	case 1 << 20:
-		size_val = 0;
-		break;
-	case 2 << 20:
-		size_val = 1;
-		break;
-	case 4 << 20:
-		size_val = 2;
-		break;
-	case 8 << 20:
-		size_val = 3;
-		break;
-	case 16 << 20:
-		size_val = 4;
-		break;
-	case 32 << 20:
-		size_val = 5;
-		break;
-	case 64 << 20:
-		size_val = 6;
-		break;
-	case 128 << 20:
-		size_val = 7;
-		break;
-	}
-	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
-	mtdcr(ebccfga, pb0cr);
-	mtdcr(ebccfgd, pbcr);
-
-	/* adjust flash start and offset */
-	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
-	gd->bd->bi_flashoffset = 0;
-
-	/* Monitor protection ON by default */
-	(void)flash_protect(FLAG_PROTECT_SET,
-			    -CFG_MONITOR_LEN,
-			    0xffffffff,
-			    &flash_info[0]);
-
-	return 0;
-}
-
-int checkboard(void)
-{
-	char *s = getenv("serial#");
-	u8 rev;
-	u8 val;
-
-	printf("Board: Yellowstone - AMCC PPC440GR Evaluation Board");
-
-	rev = *(u8 *)(CFG_CPLD + 0);
-	val = *(u8 *)(CFG_CPLD + 5) & 0x01;
-	printf(", Rev. %X, PCI=%d MHz", rev, val ? 66 : 33);
-
-	if (s != NULL) {
-		puts(", serial# ");
-		puts(s);
-	}
-	putc('\n');
-
-	return (0);
-}
-
-/*************************************************************************
- *  sdram_init -- doesn't use serial presence detect.
- *
- *  Assumes:    256 MB, ECC, non-registered
- *              PLB @ 133 MHz
- *
- ************************************************************************/
-#define NUM_TRIES 64
-#define NUM_READS 10
-
-void sdram_tr1_set(int ram_address, int* tr1_value)
-{
-	int i;
-	int j, k;
-	volatile unsigned int* ram_pointer =  (unsigned int*)ram_address;
-	int first_good = -1, last_bad = 0x1ff;
-
-	unsigned long test[NUM_TRIES] = {
-		0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
-		0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
-		0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
-		0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
-		0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
-		0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
-		0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
-		0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
-		0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
-		0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
-		0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
-		0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
-		0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
-		0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
-		0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55,
-		0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55 };
-
-	/* go through all possible SDRAM0_TR1[RDCT] values */
-	for (i=0; i<=0x1ff; i++) {
-		/* set the current value for TR1 */
-		mtsdram(mem_tr1, (0x80800800 | i));
-
-		/* write values */
-		for (j=0; j<NUM_TRIES; j++) {
-			ram_pointer[j] = test[j];
-
-			/* clear any cache at ram location */
-			__asm__("dcbf 0,%0": :"r" (&ram_pointer[j]));
-		}
-
-		/* read values back */
-		for (j=0; j<NUM_TRIES; j++) {
-			for (k=0; k<NUM_READS; k++) {
-				/* clear any cache at ram location */
-				__asm__("dcbf 0,%0": :"r" (&ram_pointer[j]));
-
-				if (ram_pointer[j] != test[j])
-					break;
-			}
-
-			/* read error */
-			if (k != NUM_READS) {
-				break;
-			}
-		}
-
-		/* we have a SDRAM0_TR1[RDCT] that is part of the window */
-		if (j == NUM_TRIES) {
-			if (first_good == -1)
-				first_good = i;		/* found beginning of window */
-		} else { /* bad read */
-			/* if we have not had a good read then don't care */
-			if(first_good != -1) {
-				/* first failure after a good read */
-				last_bad = i-1;
-				break;
-			}
-		}
-	}
-
-	/* return the current value for TR1 */
-	*tr1_value = (first_good + last_bad) / 2;
-}
-
-void sdram_init(void)
-{
-	register uint reg;
-	int tr1_bank1, tr1_bank2;
-
-	/*--------------------------------------------------------------------
-	 * Setup some default
-	 *------------------------------------------------------------------*/
-	mtsdram(mem_uabba, 0x00000000);	/* ubba=0 (default)             */
-	mtsdram(mem_slio, 0x00000000);	/* rdre=0 wrre=0 rarw=0         */
-	mtsdram(mem_devopt, 0x00000000);	/* dll=0 ds=0 (normal)          */
-	mtsdram(mem_clktr, 0x40000000);	/* ?? */
-	mtsdram(mem_wddctr, 0x40000000);	/* ?? */
-
-	/*clear this first, if the DDR is enabled by a debugger
-	  then you can not make changes. */
-	mtsdram(mem_cfg0, 0x00000000);	/* Disable EEC */
-
-	/*--------------------------------------------------------------------
-	 * Setup for board-specific specific mem
-	 *------------------------------------------------------------------*/
-	/*
-	 * Following for CAS Latency = 2.5 @ 133 MHz PLB
-	 */
-	mtsdram(mem_b0cr, 0x000a4001);	/* SDBA=0x000 128MB, Mode 3, enabled */
-	mtsdram(mem_b1cr, 0x080a4001);	/* SDBA=0x080 128MB, Mode 3, enabled */
-
-	mtsdram(mem_tr0, 0x410a4012);	/* ?? */
-	mtsdram(mem_rtr, 0x04080000);	/* ?? */
-	mtsdram(mem_cfg1, 0x00000000);	/* Self-refresh exit, disable PM    */
-	mtsdram(mem_cfg0, 0x30000000);	/* Disable EEC */
-	udelay(400);		/* Delay 200 usecs (min)            */
-
-	/*--------------------------------------------------------------------
-	 * Enable the controller, then wait for DCEN to complete
-	 *------------------------------------------------------------------*/
-	mtsdram(mem_cfg0, 0x80000000);	/* Enable */
-
-	for (;;) {
-		mfsdram(mem_mcsts, reg);
-		if (reg & 0x80000000)
-			break;
-	}
-
-	sdram_tr1_set(0x00000000, &tr1_bank1);
-	sdram_tr1_set(0x08000000, &tr1_bank2);
-	mtsdram(mem_tr1, (((tr1_bank1+tr1_bank2)/2) | 0x80800800) );
-}
-
-/*************************************************************************
- *  long int initdram
- *
- ************************************************************************/
-long int initdram(int board)
-{
-	sdram_init();
-	return CFG_SDRAM_BANKS * (CFG_KBYTES_SDRAM * 1024);	/* return bytes */
-}
-
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
-	unsigned long *mem = (unsigned long *)0;
-	const unsigned long kend = (1024 / sizeof(unsigned long));
-	unsigned long k, n;
-
-	mtmsr(0);
-
-	for (k = 0; k < CFG_KBYTES_SDRAM;
-	     ++k, mem += (1024 / sizeof(unsigned long))) {
-		if ((k & 1023) == 0) {
-			printf("%3d MB\r", k / 1024);
-		}
-
-		memset(mem, 0xaaaaaaaa, 1024);
-		for (n = 0; n < kend; ++n) {
-			if (mem[n] != 0xaaaaaaaa) {
-				printf("SDRAM test fails at: %08x\n",
-				       (uint) & mem[n]);
-				return 1;
-			}
-		}
-
-		memset(mem, 0x55555555, 1024);
-		for (n = 0; n < kend; ++n) {
-			if (mem[n] != 0x55555555) {
-				printf("SDRAM test fails at: %08x\n",
-				       (uint) & mem[n]);
-				return 1;
-			}
-		}
-	}
-	printf("SDRAM test passes\n");
-	return 0;
-}
-#endif
-
-/*************************************************************************
- *  pci_pre_init
- *
- *  This routine is called just prior to registering the hose and gives
- *  the board the opportunity to check things. Returning a value of zero
- *  indicates that things are bad & PCI initialization should be aborted.
- *
- *	Different boards may wish to customize the pci controller structure
- *	(add regions, override default access routines, etc) or perform
- *	certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
-int pci_pre_init(struct pci_controller *hose)
-{
-	unsigned long addr;
-
-	/*-------------------------------------------------------------------------+
-	  | Set priority for all PLB3 devices to 0.
-	  | Set PLB3 arbiter to fair mode.
-	  +-------------------------------------------------------------------------*/
-	mfsdr(sdr_amp1, addr);
-	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb3_acr);
-	mtdcr(plb3_acr, addr | 0x80000000);
-
-	/*-------------------------------------------------------------------------+
-	  | Set priority for all PLB4 devices to 0.
-	  +-------------------------------------------------------------------------*/
-	mfsdr(sdr_amp0, addr);
-	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
-	mtdcr(plb4_acr, addr);
-
-	/*-------------------------------------------------------------------------+
-	  | Set Nebula PLB4 arbiter to fair mode.
-	  +-------------------------------------------------------------------------*/
-	/* Segment0 */
-	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
-	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
-	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
-	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
-	mtdcr(plb0_acr, addr);
-
-	/* Segment1 */
-	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
-	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
-	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
-	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
-	mtdcr(plb1_acr, addr);
-
-	return 1;
-}
-#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
-
-/*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
-	/*--------------------------------------------------------------------------+
-	 * Set up Direct MMIO registers
-	 *--------------------------------------------------------------------------*/
-	/*--------------------------------------------------------------------------+
-	  | PowerPC440 EP PCI Master configuration.
-	  | Map one 1Gig range of PLB/processor addresses to PCI memory space.
-	  |   PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
-	  |   Use byte reversed out routines to handle endianess.
-	  | Make this region non-prefetchable.
-	  +--------------------------------------------------------------------------*/
-	out32r(PCIX0_PMM0MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
-	out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE);	/* PMM0 Local Address */
-	out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE);	/* PMM0 PCI Low Address */
-	out32r(PCIX0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIX0_PMM0MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
-
-	out32r(PCIX0_PMM1MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
-	out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2);	/* PMM0 Local Address */
-	out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2);	/* PMM0 PCI Low Address */
-	out32r(PCIX0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIX0_PMM1MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
-
-	out32r(PCIX0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
-	out32r(PCIX0_PTM1LA, 0);	/* Local Addr. Reg */
-	out32r(PCIX0_PTM2MS, 0);	/* Memory Size/Attribute */
-	out32r(PCIX0_PTM2LA, 0);	/* Local Addr. Reg */
-
-	/*--------------------------------------------------------------------------+
-	 * Set up Configuration registers
-	 *--------------------------------------------------------------------------*/
-
-	/* Program the board's subsystem id/vendor id */
-	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
-			      CFG_PCI_SUBSYS_VENDORID);
-	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID);
-
-	/* Configure command register as bus master */
-	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
-	/* 240nS PCI clock */
-	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
-	/* No error reporting */
-	pci_write_config_word(0, PCI_ERREN, 0);
-
-	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
-
-/*************************************************************************
- *  pci_master_init
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
-	unsigned short temp_short;
-
-	/*--------------------------------------------------------------------------+
-	  | Write the PowerPC440 EP PCI Configuration regs.
-	  |   Enable PowerPC440 EP to be a master on the PCI bus (PMM).
-	  |   Enable PowerPC440 EP to act as a PCI memory target (PTM).
-	  +--------------------------------------------------------------------------*/
-	pci_read_config_word(0, PCI_COMMAND, &temp_short);
-	pci_write_config_word(0, PCI_COMMAND,
-			      temp_short | PCI_COMMAND_MASTER |
-			      PCI_COMMAND_MEMORY);
-}
-#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) */
-
-/*************************************************************************
- *  is_pci_host
- *
- *	This routine is called to determine if a pci scan should be
- *	performed. With various hardware environments (especially cPCI and
- *	PPMC) it's insufficient to depend on the state of the arbiter enable
- *	bit in the strap register, or generic host/adapter assumptions.
- *
- *	Rather than hard-code a bad assumption in the general 440 code, the
- *	440 pci code requires the board to decide at runtime.
- *
- *	Return 0 for adapter mode, non-zero for host (monarch) mode.
- *
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int is_pci_host(struct pci_controller *hose)
-{
-	/* Bamboo is always configured as host. */
-	return (1);
-}
-#endif				/* defined(CONFIG_PCI) */
-
-/*************************************************************************
- *  hw_watchdog_reset
- *
- *	This routine is called to reset (keep alive) the watchdog timer
- *
- ************************************************************************/
-#if defined(CONFIG_HW_WATCHDOG)
-void hw_watchdog_reset(void)
-{
-
-}
-#endif
-
-void board_reset(void)
-{
-	/* give reset to BCSR */
-	*(unsigned char *)(CFG_BCSR_BASE | 0x06) = 0x09;
-}
diff --git a/board/amcc/yosemite/yosemite.c b/board/amcc/yosemite/yosemite.c
index d47219cb6f..c2e12ba12e 100644
--- a/board/amcc/yosemite/yosemite.c
+++ b/board/amcc/yosemite/yosemite.c
@@ -65,12 +65,14 @@ int board_early_init_f(void)
 	out32(GPIO1_TSRL, in32(GPIO1_TSRL) & ~0x0000ff00);
 	out32(GPIO1_ISR1L, in32(GPIO1_ISR1L) | 0x00005500);
 
+#ifdef CONFIG_440EP
 	/*setup USB 2.0 */
 	out32(GPIO1_TCR, in32(GPIO1_TCR) | 0xc0000000);
 	out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x50000000);
 	out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xf);
 	out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0xaa);
 	out32(GPIO0_ISR2H, in32(GPIO0_ISR2H) | 0x00000500);
+#endif
 
 	/*--------------------------------------------------------------------
 	 * Setup the interrupt controller polarities, triggers, etc.
@@ -105,8 +107,10 @@ int board_early_init_f(void)
 	/*enable ethernet */
 	*(unsigned char *)(CFG_BCSR_BASE | 0x08) = 0xf0;
 
+#ifdef CONFIG_440EP
 	/*enable usb 1.1 fs device and remove usb 2.0 reset */
 	*(unsigned char *)(CFG_BCSR_BASE | 0x09) = 0x00;
+#endif
 
 	/*get rid of flash write protect */
 	*(unsigned char *)(CFG_BCSR_BASE | 0x07) = 0x00;
@@ -171,7 +175,11 @@ int checkboard(void)
 	u8 rev;
 	u8 val;
 
+#ifdef CONFIG_440EP
 	printf("Board: Yosemite - AMCC PPC440EP Evaluation Board");
+#else
+	printf("Board: Yellowstone - AMCC PPC440GR Evaluation Board");
+#endif
 
 	rev = *(u8 *)(CFG_CPLD + 0);
 	val = *(u8 *)(CFG_CPLD + 5) & 0x01;
diff --git a/board/esd/cpci750/cpci750.c b/board/esd/cpci750/cpci750.c
index dbed597173..36bb7ce2c7 100644
--- a/board/esd/cpci750/cpci750.c
+++ b/board/esd/cpci750/cpci750.c
@@ -29,6 +29,7 @@
  */
 
 #include <common.h>
+#include <command.h>
 #include <74xx_7xx.h>
 #include "../../Marvell/include/memory.h"
 #include "../../Marvell/include/pci.h"
@@ -899,3 +900,24 @@ void board_prebootm_init ()
 	flush_data_cache ();
 	dcache_disable ();
 }
+
+
+int do_show_cfg(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+	unsigned int reset_sample_low;
+	unsigned int reset_sample_high;
+
+	GT_REG_READ(0x3c4, &reset_sample_low);
+	GT_REG_READ(0x3d4, &reset_sample_high);
+	printf("Reset configuration 0x%08x 0x%08x\n", reset_sample_low, reset_sample_high);
+
+        return(0);
+}
+
+
+U_BOOT_CMD(
+	show_cfg,	1,	1,	do_show_cfg,
+	"show_cfg- Show Marvell strapping register\n",
+	"Show Marvell strapping register (ResetSampleLow ResetSampleHigh)\n"
+	);
+
diff --git a/board/esd/cpci750/sdram_init.c b/board/esd/cpci750/sdram_init.c
index 6bdfc1d1cc..c094755351 100644
--- a/board/esd/cpci750/sdram_init.c
+++ b/board/esd/cpci750/sdram_init.c
@@ -1504,6 +1504,8 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 
 /*	for (i = info->slot * 2; i < ((info->slot * 2) + info->banks); i++) */
 	{
+	        int l, l1;
+
 		i = info->slot;
 		DP (printf
 		    ("\n*** Running a MRS cycle for bank %d ***\n", i));
@@ -1511,20 +1513,39 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 		/* map the bank */
 		memory_map_bank (i, 0, GB / 4);
 #if 1				/* test only */
-		/* set SDRAM mode */ /* To_do check it */
+
+		tmp = GTREGREAD (SDRAM_MODE);
+		GT_REG_WRITE (EXTENDED_DRAM_MODE, 0x0);
+		GT_REG_WRITE (SDRAM_OPERATION, 0x4);
+		while (GTREGREAD (SDRAM_OPERATION) != 0) {
+		        DP (printf
+			    ("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"));
+		}
+
+		GT_REG_WRITE (SDRAM_MODE, tmp | 0x80);
 		GT_REG_WRITE (SDRAM_OPERATION, 0x3);
-		check = GTREGREAD (SDRAM_OPERATION);
-		DP (printf
-		    ("\n*** SDRAM_OPERATION 1418 (0 = Normal Operation) = %08lx ***\n",
-		     check));
+		while (GTREGREAD (SDRAM_OPERATION) != 0) {
+		        DP (printf
+			    ("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"));
+		}
+		l1 = 0;
+		for (l=0;l<200;l++)
+		        l1 += GTREGREAD (SDRAM_OPERATION);
 
+		GT_REG_WRITE (SDRAM_MODE, tmp);
+		GT_REG_WRITE (SDRAM_OPERATION, 0x3);
+		while (GTREGREAD (SDRAM_OPERATION) != 0) {
+		        DP (printf
+			    ("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"));
+		}
 
 		/* switch back to normal operation mode */
-		GT_REG_WRITE (SDRAM_OPERATION, 0);
-		check = GTREGREAD (SDRAM_OPERATION);
-		DP (printf
-		    ("\n*** SDRAM_OPERATION 1418 (0 = Normal Operation) = %08lx ***\n",
-		     check));
+		GT_REG_WRITE (SDRAM_OPERATION, 0x5);
+		while (GTREGREAD (SDRAM_OPERATION) != 0) {
+		        DP (printf
+			    ("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"));
+		}
+
 #endif /* test only */
 		/* unmap the bank */
 		memory_map_bank (i, 0, 0);
diff --git a/board/amcc/yellowstone/Makefile b/board/esd/mecp5200/Makefile
index 261e5d49cc..45efdb0dec 100644
--- a/board/amcc/yellowstone/Makefile
+++ b/board/esd/mecp5200/Makefile
@@ -1,5 +1,6 @@
+
 #
-# (C) Copyright 2002-2006
+# (C) Copyright 2003-2006
 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 #
 # See file CREDITS for list of people who contributed to this
@@ -26,13 +27,12 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	= $(BOARD).o
-SOBJS	= init.o
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
 	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
diff --git a/board/amcc/yellowstone/config.mk b/board/esd/mecp5200/config.mk
index 4ab0ea0084..07b5de1881 100644
--- a/board/amcc/yellowstone/config.mk
+++ b/board/esd/mecp5200/config.mk
@@ -1,5 +1,5 @@
 #
-# (C) Copyright 2002
+# (C) Copyright 2003
 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 #
 # See file CREDITS for list of people who contributed to this
@@ -22,23 +22,23 @@
 #
 
 #
-# esd ADCIOP boards
+# IceCube board:
+#
+#	Valid values for TEXT_BASE are:
+#
+#	0xFFF00000   boot high (standard configuration)
+#	0xFF000000   boot low for 16 MiB boards
+#	0xFF800000   boot low for  8 MiB boards
+#	0x00100000   boot from RAM (for testing only)
 #
 
-#TEXT_BASE = 0x00001000
-
-ifeq ($(ramsym),1)
-TEXT_BASE = 0xFBD00000
-else
-TEXT_BASE = 0xFFF80000
-endif
-
-PLATFORM_CPPFLAGS += -DCONFIG_440=1
+sinclude $(TOPDIR)/board/$(BOARDDIR)/config.tmp
 
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG
+ifndef TEXT_BASE
+## Standard: boot high
+TEXT_BASE = 0xFFF00000
+## For testing: boot from RAM
+# TEXT_BASE = 0x00100000
 endif
 
-ifeq ($(dbcr),1)
-PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000
-endif
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR)/board
diff --git a/board/esd/mecp5200/mecp5200.c b/board/esd/mecp5200/mecp5200.c
new file mode 100644
index 0000000000..c4b91e950b
--- /dev/null
+++ b/board/esd/mecp5200/mecp5200.c
@@ -0,0 +1,261 @@
+/*
+ * (C) Copyright 2003
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * pf5200.c - main board support/init for the esd pf5200.
+ */
+
+#include <common.h>
+#include <mpc5xxx.h>
+#include <pci.h>
+#include <command.h>
+
+#include "mt46v16m16-75.h"
+
+void init_power_switch(void);
+
+static void sdram_start(int hi_addr)
+{
+	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
+
+	/* unlock mode register */
+	*(vu_long *) MPC5XXX_SDRAM_CTRL =
+	    SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
+	/* precharge all banks */
+	*(vu_long *) MPC5XXX_SDRAM_CTRL =
+	    SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
+	/* set mode register: extended mode */
+	*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
+	__asm__ volatile ("sync");
+
+	/* set mode register: reset DLL */
+	*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
+	__asm__ volatile ("sync");
+
+	/* precharge all banks */
+	*(vu_long *) MPC5XXX_SDRAM_CTRL =
+	    SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
+	/* auto refresh */
+	*(vu_long *) MPC5XXX_SDRAM_CTRL =
+	    SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
+	/* set mode register */
+	*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE;
+	__asm__ volatile ("sync");
+
+	/* normal operation */
+	*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
+	__asm__ volatile ("sync");
+}
+
+/*
+ * ATTENTION: Although partially referenced initdram does NOT make real use
+ *            use of CFG_SDRAM_BASE. The code does not work if CFG_SDRAM_BASE
+ *            is something else than 0x00000000.
+ */
+
+long int initdram(int board_type)
+{
+	ulong dramsize = 0;
+	ulong test1, test2;
+
+	/* setup SDRAM chip selects */
+	*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x0000001e;	/* 2G at 0x0 */
+	*(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x80000000;	/* disabled */
+	__asm__ volatile ("sync");
+
+	/* setup config registers */
+	*(vu_long *) MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
+	*(vu_long *) MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
+	__asm__ volatile ("sync");
+
+	/* set tap delay */
+	*(vu_long *) MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
+	__asm__ volatile ("sync");
+
+	/* find RAM size using SDRAM CS0 only */
+	sdram_start(0);
+	test1 = get_ram_size(CFG_SDRAM_BASE, 0x80000000);
+	sdram_start(1);
+	test2 = get_ram_size(CFG_SDRAM_BASE, 0x80000000);
+
+	if (test1 > test2) {
+		sdram_start(0);
+		dramsize = test1;
+	} else {
+		dramsize = test2;
+	}
+
+	/* memory smaller than 1MB is impossible */
+	if (dramsize < (1 << 20))
+		dramsize = 0;
+
+	/* set SDRAM CS0 size according to the amount of RAM found */
+	if (dramsize > 0) {
+		*(vu_long *) MPC5XXX_SDRAM_CS0CFG =
+		    0x13 + __builtin_ffs(dramsize >> 20) - 1;
+		/* let SDRAM CS1 start right after CS0 */
+		*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;	/* 2G */
+	} else {
+#if 0
+		*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0;	/* disabled */
+		/* let SDRAM CS1 start right after CS0 */
+		*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;	/* 2G */
+#else
+		*(vu_long *) MPC5XXX_SDRAM_CS0CFG =
+		    0x13 + __builtin_ffs(0x08000000 >> 20) - 1;
+		/* let SDRAM CS1 start right after CS0 */
+		*(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x08000000 + 0x0000001e;	/* 2G */
+#endif
+	}
+
+#if 0
+	/* find RAM size using SDRAM CS1 only */
+	sdram_start(0);
+	get_ram_size((ulong *) (CFG_SDRAM_BASE + dramsize), 0x80000000);
+	sdram_start(1);
+	get_ram_size((ulong *) (CFG_SDRAM_BASE + dramsize), 0x80000000);
+	sdram_start(0);
+#endif
+	/* set SDRAM CS1 size according to the amount of RAM found */
+
+	*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize;	/* disabled */
+
+	init_power_switch();
+	return (dramsize);
+}
+
+int checkboard(void)
+{
+	puts("Board: esd CPX CPU5200 (mecp5200)\n");
+	return 0;
+}
+
+void flash_preinit(void)
+{
+	/*
+	 * Now, when we are in RAM, enable flash write
+	 * access for detection process.
+	 * Note that CS_BOOT cannot be cleared when
+	 * executing in flash.
+	 */
+	*(vu_long *) MPC5XXX_BOOTCS_CFG &= ~0x1;	/* clear RO */
+}
+
+void flash_afterinit(ulong size)
+{
+	if (size == CFG_FLASH_SIZE) {
+		/* adjust mapping */
+		*(vu_long *) MPC5XXX_BOOTCS_START =
+		    *(vu_long *) MPC5XXX_CS0_START =
+		    START_REG(CFG_BOOTCS_START | size);
+		*(vu_long *) MPC5XXX_BOOTCS_STOP =
+		    *(vu_long *) MPC5XXX_CS0_STOP =
+		    STOP_REG(CFG_BOOTCS_START | size, size);
+	}
+}
+
+#ifdef	CONFIG_PCI
+static struct pci_controller hose;
+
+extern void pci_mpc5xxx_init(struct pci_controller *);
+
+void pci_init_board(void)
+{
+	pci_mpc5xxx_init(&hose);
+}
+#endif
+
+#if defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET)
+
+#define GPIO_PSC1_4	0x01000000UL
+
+void init_ide_reset(void)
+{
+	debug("init_ide_reset\n");
+
+	/* Configure PSC1_4 as GPIO output for ATA reset */
+	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
+	*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
+}
+
+void ide_set_reset(int idereset)
+{
+	debug("ide_reset(%d)\n", idereset);
+
+	if (idereset)
+		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
+	else
+		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
+}
+#endif				/* defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET) */
+
+#define MPC5XXX_SIMPLEIO_GPIO_ENABLE       (MPC5XXX_GPIO + 0x0004)
+#define MPC5XXX_SIMPLEIO_GPIO_DIR          (MPC5XXX_GPIO + 0x000C)
+#define MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT  (MPC5XXX_GPIO + 0x0010)
+#define MPC5XXX_SIMPLEIO_GPIO_DATA_INPUT   (MPC5XXX_GPIO + 0x0014)
+
+#define MPC5XXX_INTERRUPT_GPIO_ENABLE      (MPC5XXX_GPIO + 0x0020)
+#define MPC5XXX_INTERRUPT_GPIO_DIR         (MPC5XXX_GPIO + 0x0028)
+#define MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT (MPC5XXX_GPIO + 0x002C)
+#define MPC5XXX_INTERRUPT_GPIO_STATUS      (MPC5XXX_GPIO + 0x003C)
+
+#define GPIO_WU6	0x40000000UL
+#define GPIO_USB0       0x00010000UL
+#define GPIO_USB9       0x08000000UL
+#define GPIO_USB9S      0x00080000UL
+
+void init_power_switch(void)
+{
+	debug("init_power_switch\n");
+
+	/* Configure GPIO_WU6 as GPIO output for ATA reset */
+	*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_WU6;
+	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_WU6;
+	*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_WU6;
+	__asm__ volatile ("sync");
+
+	*(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT &= ~GPIO_USB0;
+	*(vu_long *) MPC5XXX_SIMPLEIO_GPIO_ENABLE |= GPIO_USB0;
+	*(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DIR |= GPIO_USB0;
+	__asm__ volatile ("sync");
+
+	*(vu_long *) MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT &= ~GPIO_USB9;
+	*(vu_long *) MPC5XXX_INTERRUPT_GPIO_ENABLE &= ~GPIO_USB9;
+	__asm__ volatile ("sync");
+
+	if ((*(vu_long *) MPC5XXX_INTERRUPT_GPIO_STATUS & GPIO_USB9S) == 0) {
+		*(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT |= GPIO_USB0;
+		__asm__ volatile ("sync");
+	}
+}
diff --git a/board/esd/mecp5200/mt46v16m16-75.h b/board/esd/mecp5200/mt46v16m16-75.h
new file mode 100644
index 0000000000..22d0a55444
--- /dev/null
+++ b/board/esd/mecp5200/mt46v16m16-75.h
@@ -0,0 +1,37 @@
+/*
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define SDRAM_DDR	1	/* is DDR */
+
+#if defined(CONFIG_MPC5200)
+/* Settings for XLB = 132 MHz */
+#define SDRAM_MODE	0x018D0000
+#define SDRAM_EMODE	0x40090000
+#define SDRAM_CONTROL	0x705f0f00
+#define SDRAM_CONFIG1	0x73722930
+#define SDRAM_CONFIG2	0x47770000
+#define SDRAM_TAPDELAY	0x10000000
+
+#else
+#error CONFIG_MPC5200 not defined
+#endif
diff --git a/board/amcc/yellowstone/u-boot.lds b/board/esd/mecp5200/u-boot.lds
index a0ba44de88..d999dd16ad 100644
--- a/board/amcc/yellowstone/u-boot.lds
+++ b/board/esd/mecp5200/u-boot.lds
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2002
+ * (C) Copyright 2003
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -27,16 +27,6 @@ SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/
    __DYNAMIC = 0;    */
 SECTIONS
 {
-  .resetvec 0xFFFFFFFC :
-  {
-    *(.resetvec)
-  } = 0xffff
-
-  .bootpg 0xFFFFF000 :
-  {
-    cpu/ppc4xx/start.o	(.bootpg)
-  } = 0xffff
-
   /* Read-only sections, merged into text segment: */
   . = + SIZEOF_HEADERS;
   .interp : { *(.interp) }
@@ -63,44 +53,21 @@ SECTIONS
   .plt : { *(.plt) }
   .text      :
   {
-    /* WARNING - the following is hand-optimized to fit within	*/
-    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
-
-    cpu/ppc4xx/start.o	(.text)
-    board/amcc/yellowstone/init.o	(.text)
-    cpu/ppc4xx/kgdb.o	(.text)
-    cpu/ppc4xx/traps.o	(.text)
-    cpu/ppc4xx/interrupts.o	(.text)
-    cpu/ppc4xx/serial.o	(.text)
-    cpu/ppc4xx/cpu_init.o	(.text)
-    cpu/ppc4xx/speed.o	(.text)
-    common/dlmalloc.o	(.text)
-    lib_generic/crc32.o		(.text)
-    lib_ppc/extable.o	(.text)
-    lib_generic/zlib.o		(.text)
-
-/*    . = env_offset;*/
-/*    common/environment.o(.text)*/
-
+    cpu/mpc5xxx/start.o	(.text)
     *(.text)
     *(.fixup)
     *(.got1)
-  }
-  _etext = .;
-  PROVIDE (etext = .);
-  .rodata    :
-  {
+    . = ALIGN(16);
     *(.rodata)
     *(.rodata1)
     *(.rodata.str1.4)
-    *(.eh_frame)
   }
   .fini      : { *(.fini)    } =0
   .ctors     : { *(.ctors)   }
   .dtors     : { *(.dtors)   }
 
   /* Read-write section, merged into data segment: */
-  . = (. + 0x00FF) & 0xFFFFFF00;
+  . = (. + 0x0FFF) & 0xFFFFF000;
   _erotext = .;
   PROVIDE (erotext = .);
   .reloc   :
@@ -111,8 +78,8 @@ SECTIONS
     _FIXUP_TABLE_ = .;
     *(.fixup)
   }
-  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
-  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
 
   .data    :
   {
@@ -126,22 +93,20 @@ SECTIONS
   _edata  =  .;
   PROVIDE (edata = .);
 
-  . = .;
   __u_boot_cmd_start = .;
   .u_boot_cmd : { *(.u_boot_cmd) }
   __u_boot_cmd_end = .;
 
 
-  . = .;
   __start___ex_table = .;
   __ex_table : { *(__ex_table) }
   __stop___ex_table = .;
 
-  . = ALIGN(256);
+  . = ALIGN(4096);
   __init_begin = .;
   .text.init : { *(.text.init) }
   .data.init : { *(.data.init) }
-  . = ALIGN(256);
+  . = ALIGN(4096);
   __init_end = .;
 
   __bss_start = .;
diff --git a/board/prodrive/p3mx/p3mx.h b/board/prodrive/p3mx/p3mx.h
new file mode 100644
index 0000000000..91071e9209
--- /dev/null
+++ b/board/prodrive/p3mx/p3mx.h
@@ -0,0 +1,34 @@
+/*
+ * (C) Copyright 2005
+ *
+ * Roel Loeffen, (C) Copyright 2006 Prodrive B.V. roel.loeffen@prodrive.nl
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __P3MX_H__
+#define __P3MX_H__
+
+#define LED_OFF		1
+#define LED_GREEN	2
+#define LED_RED		3
+#define LED_ORANGE	4
+
+#endif /* __P3MX_H__ */
+