Merge branch 'master' into hpc2

Conflicts:

	drivers/Makefile
Fix the merge conflict in file drivers/Makefile
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>

31 files changed, 1738 insertions, 107 deletions

diff --git a/board/amcc/katmai/Makefile b/board/amcc/katmai/Makefile
new file mode 100644
index 0000000000..d06a402d17
--- /dev/null
+++ b/board/amcc/katmai/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2007
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	= $(BOARD).o cmd_katmai.o
+SOBJS	= init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend *~
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/amcc/katmai/cmd_katmai.c b/board/amcc/katmai/cmd_katmai.c
new file mode 100644
index 0000000000..684f6a5863
--- /dev/null
+++ b/board/amcc/katmai/cmd_katmai.c
@@ -0,0 +1,267 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <asm/byteorder.h>
+
+static int do_bootstrap(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	uchar	chip;
+	ulong	data;
+	int	nbytes;
+	extern char console_buffer[];
+
+	char sysClock[4];
+	char cpuClock[4];
+	char plbClock[4];
+	char pcixClock[4];
+
+	if (argc < 3) {
+		printf ("Usage:\n%s\n", cmdtp->usage);
+		return 1;
+	}
+
+	if (strcmp(argv[2], "prom0") == 0)
+		chip = IIC0_BOOTPROM_ADDR;
+	else
+		chip = IIC0_ALT_BOOTPROM_ADDR;
+
+	do {
+		printf("enter sys clock frequency 33 or 66 Mhz or quit to abort\n");
+		nbytes = readline (" ? ");
+
+		if (strcmp(console_buffer, "quit") == 0)
+			return 0;
+
+		if ((strcmp(console_buffer, "33") != 0) &
+		    (strcmp(console_buffer, "66") != 0))
+			nbytes=0;
+
+		strcpy(sysClock, console_buffer);
+
+	} while (nbytes == 0);
+
+	do {
+		if (strcmp(sysClock, "66") == 0) {
+			printf("enter cpu clock frequency 400, 533 Mhz or quit to abort\n");
+		} else {
+#ifdef	CONFIG_STRESS
+			printf("enter cpu clock frequency 400, 500, 533, 667 Mhz or quit to abort\n");
+#else
+			printf("enter cpu clock frequency 400, 500, 533 Mhz or quit to abort\n");
+#endif
+		}
+		nbytes = readline (" ? ");
+
+		if (strcmp(console_buffer, "quit") == 0)
+			return 0;
+
+		if (strcmp(sysClock, "66") == 0) {
+			if ((strcmp(console_buffer, "400") != 0) &
+			    (strcmp(console_buffer, "533") != 0)
+#ifdef	CONFIG_STRESS
+			    & (strcmp(console_buffer, "667") != 0)
+#endif
+				) {
+				nbytes = 0;
+			}
+		} else {
+			if ((strcmp(console_buffer, "400") != 0) &
+			    (strcmp(console_buffer, "500") != 0) &
+			    (strcmp(console_buffer, "533") != 0)
+#ifdef	CONFIG_STRESS
+			    & (strcmp(console_buffer, "667") != 0)
+#endif
+				) {
+				nbytes = 0;
+			}
+		}
+
+		strcpy(cpuClock, console_buffer);
+
+	} while (nbytes == 0);
+
+	if (strcmp(cpuClock, "500") == 0)
+		strcpy(plbClock, "166");
+	else if (strcmp(cpuClock, "533") == 0)
+		strcpy(plbClock, "133");
+	else {
+		do {
+			if (strcmp(cpuClock, "400") == 0)
+				printf("enter plb clock frequency 100, 133 Mhz or quit to abort\n");
+
+#ifdef	CONFIG_STRESS
+			if (strcmp(cpuClock, "667") == 0)
+				printf("enter plb clock frequency 133, 166 Mhz or quit to abort\n");
+
+#endif
+			nbytes = readline (" ? ");
+
+			if (strcmp(console_buffer, "quit") == 0)
+				return 0;
+
+			if (strcmp(cpuClock, "400") == 0) {
+				if ((strcmp(console_buffer, "100") != 0) &
+				    (strcmp(console_buffer, "133") != 0))
+					nbytes = 0;
+			}
+#ifdef	CONFIG_STRESS
+			if (strcmp(cpuClock, "667") == 0) {
+				if ((strcmp(console_buffer, "133") != 0) &
+				    (strcmp(console_buffer, "166") != 0))
+					nbytes = 0;
+			}
+#endif
+			strcpy(plbClock, console_buffer);
+
+		} while (nbytes == 0);
+	}
+
+	do {
+		printf("enter Pci-X clock frequency 33, 66, 100 or 133 Mhz or quit to abort\n");
+		nbytes = readline (" ? ");
+
+		if (strcmp(console_buffer, "quit") == 0)
+			return 0;
+
+		if ((strcmp(console_buffer, "33") != 0) &
+		    (strcmp(console_buffer, "66") != 0) &
+		    (strcmp(console_buffer, "100") != 0) &
+		    (strcmp(console_buffer, "133") != 0)) {
+			nbytes = 0;
+		}
+		strcpy(pcixClock, console_buffer);
+
+	} while (nbytes == 0);
+
+	printf("\nsys clk   = %sMhz\n", sysClock);
+	printf("cpu clk   = %sMhz\n", cpuClock);
+	printf("plb clk   = %sMhz\n", plbClock);
+	printf("Pci-X clk = %sMhz\n", pcixClock);
+
+	do {
+		printf("\npress [y] to write I2C bootstrap \n");
+		printf("or [n] to abort.  \n");
+		printf("Don't forget to set board switches \n");
+		printf("according to your choice before re-starting \n");
+		printf("(refer to 440spe_uboot_kit_um_1_01.pdf) \n");
+
+		nbytes = readline (" ? ");
+		if (strcmp(console_buffer, "n") == 0)
+			return 0;
+
+	} while (nbytes == 0);
+
+	if (strcmp(sysClock, "33") == 0) {
+		if ((strcmp(cpuClock, "400") == 0) &
+		    (strcmp(plbClock, "100") == 0))
+			data = 0x8678c206;
+
+		if ((strcmp(cpuClock, "400") == 0) &
+		    (strcmp(plbClock, "133") == 0))
+			data = 0x8678c2c6;
+
+		if ((strcmp(cpuClock, "500") == 0))
+			data = 0x8778f2c6;
+
+		if ((strcmp(cpuClock, "533") == 0))
+			data = 0x87790252;
+
+#ifdef	CONFIG_STRESS
+		if ((strcmp(cpuClock, "667") == 0) &
+		    (strcmp(plbClock, "133") == 0))
+			data = 0x87794256;
+
+		if ((strcmp(cpuClock, "667") == 0) &
+		    (strcmp(plbClock, "166") == 0))
+			data = 0x87794206;
+
+#endif
+	}
+	if (strcmp(sysClock, "66") == 0) {
+		if ((strcmp(cpuClock, "400") == 0) &
+		    (strcmp(plbClock, "100") == 0))
+			data = 0x84706206;
+
+		if ((strcmp(cpuClock, "400") == 0) &
+		    (strcmp(plbClock, "133") == 0))
+			data = 0x847062c6;
+
+		if ((strcmp(cpuClock, "533") == 0))
+			data = 0x85708206;
+
+#ifdef	CONFIG_STRESS
+		if ((strcmp(cpuClock, "667") == 0) &
+		    (strcmp(plbClock, "133") == 0))
+			data = 0x8570a256;
+
+		if ((strcmp(cpuClock, "667") == 0) &
+		    (strcmp(plbClock, "166") == 0))
+			data = 0x8570a206;
+
+#endif
+	}
+
+#ifdef	DEBUG
+	printf(" pin strap0 to write in i2c  = %x\n", data);
+#endif	/* DEBUG */
+
+	if (i2c_write(chip, 0, 1, (uchar *)&data, 4) != 0)
+		printf("Error writing strap0 in %s\n", argv[2]);
+
+	if (strcmp(pcixClock, "33") == 0)
+		data = 0x00000701;
+
+	if (strcmp(pcixClock, "66") == 0)
+		data = 0x00000601;
+
+	if (strcmp(pcixClock, "100") == 0)
+		data = 0x00000501;
+
+	if (strcmp(pcixClock, "133") == 0)
+		data = 0x00000401;
+
+	if (strcmp(plbClock, "166") == 0)
+		data |= 0x05950000;
+	else
+		data |= 0x05A50000;
+
+#ifdef	DEBUG
+	printf(" pin strap1 to write in i2c  = %x\n", data);
+#endif	/* DEBUG */
+
+	udelay(1000);
+	if (i2c_write(chip, 4, 1, (uchar *)&data, 4) != 0)
+		printf("Error writing strap1 in %s\n", argv[2]);
+
+	return 0;
+}
+
+U_BOOT_CMD(
+	bootstrap,	3,	1,	do_bootstrap,
+	"bootstrap - program the serial device strap\n",
+	"wrclk [prom0|prom1] - program the serial device strap\n"
+	);
diff --git a/board/amcc/katmai/config.mk b/board/amcc/katmai/config.mk
new file mode 100644
index 0000000000..115c1aed05
--- /dev/null
+++ b/board/amcc/katmai/config.mk
@@ -0,0 +1,38 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# AMCC 440SPe Evaluation (Katmai) board
+#
+
+TEXT_BASE = 0xfffc0000
+
+PLATFORM_CPPFLAGS += -DCONFIG_440=1
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif
+
+ifeq ($(dbcr),1)
+PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000
+endif
diff --git a/board/amcc/katmai/init.S b/board/amcc/katmai/init.S
new file mode 100644
index 0000000000..f5900bcb7b
--- /dev/null
+++ b/board/amcc/katmai/init.S
@@ -0,0 +1,108 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ *  Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <config.h>
+#include <asm-ppc/mmu.h>
+
+/**************************************************************************
+ * TLB TABLE
+ *
+ * This table is used by the cpu boot code to setup the initial tlb
+ * entries. Rather than make broad assumptions in the cpu source tree,
+ * this table lets each board set things up however they like.
+ *
+ *  Pointer to the table is returned in r1
+ *
+ *************************************************************************/
+
+	.section .bootpg,"ax"
+
+/**************************************************************************
+ * TLB table for revA
+ *************************************************************************/
+	.globl tlbtabA
+tlbtabA:
+	tlbtab_start
+	tlbentry(0xff000000, SZ_16M, 0xff000000, 4, AC_R|AC_W|AC_X|SA_G)
+
+	/*
+	 * TLB entries for SDRAM are not needed on this platform.
+	 * They are dynamically generated in the SPD DDR(2) detection
+	 * routine.
+	 */
+
+	tlbentry(CFG_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_R|AC_W|AC_X|SA_I)
+	tlbentry(CFG_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_R|AC_W|SA_G|SA_I)
+
+	tlbentry(CFG_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE_BASE, SZ_16K, 0x20000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+
+	tlbentry(CFG_PCIE0_CFGBASE, SZ_1K, 0x40000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE1_CFGBASE, SZ_1K, 0x80000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE2_CFGBASE, SZ_1K, 0xC0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE0_XCFGBASE, SZ_1K, 0x50000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE1_XCFGBASE, SZ_1K, 0x90000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE2_XCFGBASE, SZ_1K, 0xD0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbtab_end
+
+/**************************************************************************
+ * TLB table for revB
+ *
+ * Notice: revB of the 440SPe chip is very strict about PLB real addresses
+ * and ranges to be mapped for config space: it seems to only work with
+ * d_nnnn_nnnn range (hangs the core upon config transaction attempts when
+ * set otherwise) while revA uses c_nnnn_nnnn.
+ *************************************************************************/
+	.globl tlbtabB
+tlbtabB:
+	tlbtab_start
+	tlbentry(0xff000000, SZ_16M, 0xff000000, 4, AC_R|AC_W|AC_X|SA_G)
+
+	/*
+	 * TLB entries for SDRAM are not needed on this platform.
+	 * They are dynamically generated in the SPD DDR(2) detection
+	 * routine.
+	 */
+
+	tlbentry(CFG_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_R|AC_W|AC_X|SA_I)
+
+	tlbentry(CFG_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_R|AC_W|SA_G|SA_I)
+
+	tlbentry(CFG_ACE_BASE, SZ_1K, 0xE0000000, 4,AC_R|AC_W|SA_G|SA_I)
+
+	tlbentry(CFG_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+
+	tlbentry(CFG_PCIE0_CFGBASE, SZ_1K, 0x00100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE1_CFGBASE, SZ_1K, 0x20100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE2_CFGBASE, SZ_1K, 0x40100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE0_XCFGBASE, SZ_1K, 0x10000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE1_XCFGBASE, SZ_1K, 0x30000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE2_XCFGBASE, SZ_1K, 0x50000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbtab_end
diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c
new file mode 100644
index 0000000000..8704925a9c
--- /dev/null
+++ b/board/amcc/katmai/katmai.c
@@ -0,0 +1,514 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+#include <i2c.h>
+#include <asm-ppc/io.h>
+
+#include "katmai.h"
+#include "../cpu/ppc4xx/440spe_pcie.h"
+
+#undef PCIE_ENDPOINT
+/* #define PCIE_ENDPOINT 1 */
+
+int ppc440spe_init_pcie_rootport(int port);
+void ppc440spe_setup_pcie(struct pci_controller *hose, int port);
+
+int board_early_init_f (void)
+{
+	unsigned long mfr;
+	unsigned long pfc;
+
+	/*----------------------------------------------------------------------+
+	 * Interrupt controller setup for the Katmai 440SPe Evaluation board.
+	 *-----------------------------------------------------------------------+
+	 *-----------------------------------------------------------------------+
+	 * Interrupt | Source                            | Pol.  | Sensi.| Crit. |
+	 *-----------+-----------------------------------+-------+-------+-------+
+	 * IRQ 00    | UART0                             | High  | Level | Non   |
+	 * IRQ 01    | UART1                             | High  | Level | Non   |
+	 * IRQ 02    | IIC0                              | High  | Level | Non   |
+	 * IRQ 03    | IIC1                              | High  | Level | Non   |
+	 * IRQ 04    | PCI0X0 MSG IN                     | High  | Level | Non   |
+	 * IRQ 05    | PCI0X0 CMD Write                  | High  | Level | Non   |
+	 * IRQ 06    | PCI0X0 Power Mgt                  | High  | Level | Non   |
+	 * IRQ 07    | PCI0X0 VPD Access                 | Rising| Edge  | Non   |
+	 * IRQ 08    | PCI0X0 MSI level 0                | High  | Lvl/ed| Non   |
+	 * IRQ 09    | External IRQ 15 - (PCI-Express)   | pgm H | Pgm   | Non   |
+	 * IRQ 10    | UIC2 Non-critical Int.            | NA    | NA    | Non   |
+	 * IRQ 11    | UIC2 Critical Interrupt           | NA    | NA    | Crit  |
+	 * IRQ 12    | PCI Express MSI Level 0           | Rising| Edge  | Non   |
+	 * IRQ 13    | PCI Express MSI Level 1           | Rising| Edge  | Non   |
+	 * IRQ 14    | PCI Express MSI Level 2           | Rising| Edge  | Non   |
+	 * IRQ 15    | PCI Express MSI Level 3           | Rising| Edge  | Non   |
+	 * IRQ 16    | UIC3 Non-critical Int.            | NA    | NA    | Non   |
+	 * IRQ 17    | UIC3 Critical Interrupt           | NA    | NA    | Crit  |
+	 * IRQ 18    | External IRQ 14 - (PCI-Express)   | Pgm   | Pgm   | Non   |
+	 * IRQ 19    | DMA Channel 0 FIFO Full           | High  | Level | Non   |
+	 * IRQ 20    | DMA Channel 0 Stat FIFO           | High  | Level | Non   |
+	 * IRQ 21    | DMA Channel 1 FIFO Full           | High  | Level | Non   |
+	 * IRQ 22    | DMA Channel 1 Stat FIFO           | High  | Level | Non   |
+	 * IRQ 23    | I2O Inbound Doorbell              | High  | Level | Non   |
+	 * IRQ 24    | Inbound Post List FIFO Not Empt   | High  | Level | Non   |
+	 * IRQ 25    | I2O Region 0 LL PLB Write         | High  | Level | Non   |
+	 * IRQ 26    | I2O Region 1 LL PLB Write         | High  | Level | Non   |
+	 * IRQ 27    | I2O Region 0 HB PLB Write         | High  | Level | Non   |
+	 * IRQ 28    | I2O Region 1 HB PLB Write         | High  | Level | Non   |
+	 * IRQ 29    | GPT Down Count Timer              | Rising| Edge  | Non   |
+	 * IRQ 30    | UIC1 Non-critical Int.            | NA    | NA    | Non   |
+	 * IRQ 31    | UIC1 Critical Interrupt           | NA    | NA    | Crit. |
+	 *------------------------------------------------------------------------
+	 * IRQ 32    | Ext. IRQ 13 - (PCI-Express)       |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 33    | MAL Serr                          | High  | Level | Non   |
+	 * IRQ 34    | MAL Txde                          | High  | Level | Non   |
+	 * IRQ 35    | MAL Rxde                          | High  | Level | Non   |
+	 * IRQ 36    | DMC CE or DMC UE                  | High  | Level | Non   |
+	 * IRQ 37    | EBC or UART2                      | High  |Lvl Edg| Non   |
+	 * IRQ 38    | MAL TX EOB                        | High  | Level | Non   |
+	 * IRQ 39    | MAL RX EOB                        | High  | Level | Non   |
+	 * IRQ 40    | PCIX0 MSI Level 1                 | High  |Lvl Edg| Non   |
+	 * IRQ 41    | PCIX0 MSI level 2                 | High  |Lvl Edg| Non   |
+	 * IRQ 42    | PCIX0 MSI level 3                 | High  |Lvl Edg| Non   |
+	 * IRQ 43    | L2 Cache                          | Risin | Edge  | Non   |
+	 * IRQ 44    | GPT Compare Timer 0               | Risin | Edge  | Non   |
+	 * IRQ 45    | GPT Compare Timer 1               | Risin | Edge  | Non   |
+	 * IRQ 46    | GPT Compare Timer 2               | Risin | Edge  | Non   |
+	 * IRQ 47    | GPT Compare Timer 3               | Risin | Edge  | Non   |
+	 * IRQ 48    | GPT Compare Timer 4               | Risin | Edge  | Non   |
+	 * IRQ 49    | Ext. IRQ 12 - PCI-X               |pgm/Fal|pgm/Lvl| Non   |
+	 * IRQ 50    | Ext. IRQ 11 -                     |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 51    | Ext. IRQ 10 -                     |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 52    | Ext. IRQ 9                        |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 53    | Ext. IRQ 8                        |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 54    | DMA Error                         | High  | Level | Non   |
+	 * IRQ 55    | DMA I2O Error                     | High  | Level | Non   |
+	 * IRQ 56    | Serial ROM                        | High  | Level | Non   |
+	 * IRQ 57    | PCIX0 Error                       | High  | Edge  | Non   |
+	 * IRQ 58    | Ext. IRQ 7-                       |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 59    | Ext. IRQ 6-                       |pgm (H)|pgm/Lvl| Non   |
+	 * IRQ 60    | EMAC0 Interrupt                   | High  | Level | Non   |
+	 * IRQ 61    | EMAC0 Wake-up                     | High  | Level | Non   |
+	 * IRQ 62    | Reserved                          | High  | Level | Non   |
+	 * IRQ 63    | XOR                               | High  | Level | Non   |
+	 *-----------------------------------------------------------------------
+	 * IRQ 64    | PE0 AL                            | High  | Level | Non   |
+	 * IRQ 65    | PE0 VPD Access                    | Risin | Edge  | Non   |
+	 * IRQ 66    | PE0 Hot Reset Request             | Risin | Edge  | Non   |
+	 * IRQ 67    | PE0 Hot Reset Request             | Falli | Edge  | Non   |
+	 * IRQ 68    | PE0 TCR                           | High  | Level | Non   |
+	 * IRQ 69    | PE0 BusMaster VCO                 | Falli | Edge  | Non   |
+	 * IRQ 70    | PE0 DCR Error                     | High  | Level | Non   |
+	 * IRQ 71    | Reserved                          | N/A   | N/A   | Non   |
+	 * IRQ 72    | PE1 AL                            | High  | Level | Non   |
+	 * IRQ 73    | PE1 VPD Access                    | Risin | Edge  | Non   |
+	 * IRQ 74    | PE1 Hot Reset Request             | Risin | Edge  | Non   |
+	 * IRQ 75    | PE1 Hot Reset Request             | Falli | Edge  | Non   |
+	 * IRQ 76    | PE1 TCR                           | High  | Level | Non   |
+	 * IRQ 77    | PE1 BusMaster VCO                 | Falli | Edge  | Non   |
+	 * IRQ 78    | PE1 DCR Error                     | High  | Level | Non   |
+	 * IRQ 79    | Reserved                          | N/A   | N/A   | Non   |
+	 * IRQ 80    | PE2 AL                            | High  | Level | Non   |
+	 * IRQ 81    | PE2 VPD Access                    | Risin | Edge  | Non   |
+	 * IRQ 82    | PE2 Hot Reset Request             | Risin | Edge  | Non   |
+	 * IRQ 83    | PE2 Hot Reset Request             | Falli | Edge  | Non   |
+	 * IRQ 84    | PE2 TCR                           | High  | Level | Non   |
+	 * IRQ 85    | PE2 BusMaster VCO                 | Falli | Edge  | Non   |
+	 * IRQ 86    | PE2 DCR Error                     | High  | Level | Non   |
+	 * IRQ 87    | Reserved                          | N/A   | N/A   | Non   |
+	 * IRQ 88    | External IRQ(5)                   | Progr | Progr | Non   |
+	 * IRQ 89    | External IRQ 4 - Ethernet         | Progr | Progr | Non   |
+	 * IRQ 90    | External IRQ 3 - PCI-X            | Progr | Progr | Non   |
+	 * IRQ 91    | External IRQ 2 - PCI-X            | Progr | Progr | Non   |
+	 * IRQ 92    | External IRQ 1 - PCI-X            | Progr | Progr | Non   |
+	 * IRQ 93    | External IRQ 0 - PCI-X            | Progr | Progr | Non   |
+	 * IRQ 94    | Reserved                          | N/A   | N/A   | Non   |
+	 * IRQ 95    | Reserved                          | N/A   | N/A   | Non   |
+	 *-----------------------------------------------------------------------
+	 * IRQ 96    | PE0 INTA                          | High  | Level | Non   |
+	 * IRQ 97    | PE0 INTB                          | High  | Level | Non   |
+	 * IRQ 98    | PE0 INTC                          | High  | Level | Non   |
+	 * IRQ 99    | PE0 INTD                          | High  | Level | Non   |
+	 * IRQ 100   | PE1 INTA                          | High  | Level | Non   |
+	 * IRQ 101   | PE1 INTB                          | High  | Level | Non   |
+	 * IRQ 102   | PE1 INTC                          | High  | Level | Non   |
+	 * IRQ 103   | PE1 INTD                          | High  | Level | Non   |
+	 * IRQ 104   | PE2 INTA                          | High  | Level | Non   |
+	 * IRQ 105   | PE2 INTB                          | High  | Level | Non   |
+	 * IRQ 106   | PE2 INTC                          | High  | Level | Non   |
+	 * IRQ 107   | PE2 INTD                          | Risin | Edge  | Non   |
+	 * IRQ 108   | PCI Express MSI Level 4           | Risin | Edge  | Non   |
+	 * IRQ 109   | PCI Express MSI Level 5           | Risin | Edge  | Non   |
+	 * IRQ 110   | PCI Express MSI Level 6           | Risin | Edge  | Non   |
+	 * IRQ 111   | PCI Express MSI Level 7           | Risin | Edge  | Non   |
+	 * IRQ 116   | PCI Express MSI Level 12          | Risin | Edge  | Non   |
+	 * IRQ 112   | PCI Express MSI Level 8           | Risin | Edge  | Non   |
+	 * IRQ 113   | PCI Express MSI Level 9           | Risin | Edge  | Non   |
+	 * IRQ 114   | PCI Express MSI Level 10          | Risin | Edge  | Non   |
+	 * IRQ 115   | PCI Express MSI Level 11          | Risin | Edge  | Non   |
+	 * IRQ 117   | PCI Express MSI Level 13          | Risin | Edge  | Non   |
+	 * IRQ 118   | PCI Express MSI Level 14          | Risin | Edge  | Non   |
+	 * IRQ 119   | PCI Express MSI Level 15          | Risin | Edge  | Non   |
+	 * IRQ 120   | PCI Express MSI Level 16          | Risin | Edge  | Non   |
+	 * IRQ 121   | PCI Express MSI Level 17          | Risin | Edge  | Non   |
+	 * IRQ 122   | PCI Express MSI Level 18          | Risin | Edge  | Non   |
+	 * IRQ 123   | PCI Express MSI Level 19          | Risin | Edge  | Non   |
+	 * IRQ 124   | PCI Express MSI Level 20          | Risin | Edge  | Non   |
+	 * IRQ 125   | PCI Express MSI Level 21          | Risin | Edge  | Non   |
+	 * IRQ 126   | PCI Express MSI Level 22          | Risin | Edge  | Non   |
+	 * IRQ 127   | PCI Express MSI Level 23          | Risin | Edge  | Non   |
+	 *-----------+-----------------------------------+-------+-------+-------+ */
+	/*-------------------------------------------------------------------------+
+	 * Put UICs in PowerPC440SPemode.
+	 * Initialise UIC registers.  Clear all interrupts.  Disable all interrupts.
+	 * Set critical interrupt values.  Set interrupt polarities.  Set interrupt
+	 * trigger levels.  Make bit 0 High  priority.  Clear all interrupts again.
+	 *------------------------------------------------------------------------*/
+	mtdcr (uic3sr, 0xffffffff);	/* Clear all interrupts */
+	mtdcr (uic3er, 0x00000000);	/* disable all interrupts */
+	mtdcr (uic3cr, 0x00000000);	/* Set Critical / Non Critical interrupts: */
+	mtdcr (uic3pr, 0xffffffff);	/* Set Interrupt Polarities*/
+	mtdcr (uic3tr, 0x001fffff);	/* Set Interrupt Trigger Levels */
+	mtdcr (uic3vr, 0x00000001);	/* Set Vect base=0,INT31 Highest priority */
+	mtdcr (uic3sr, 0x00000000);	/* clear all  interrupts*/
+	mtdcr (uic3sr, 0xffffffff);	/* clear all  interrupts*/
+
+
+	mtdcr (uic2sr, 0xffffffff);	/* Clear all interrupts */
+	mtdcr (uic2er, 0x00000000);	/* disable all interrupts*/
+	mtdcr (uic2cr, 0x00000000);	/* Set Critical / Non Critical interrupts*/
+	mtdcr (uic2pr, 0xebebebff);	/* Set Interrupt Polarities*/
+	mtdcr (uic2tr, 0x74747400);	/* Set Interrupt Trigger Levels */
+	mtdcr (uic2vr, 0x00000001);	/* Set Vect base=0,INT31 Highest priority */
+	mtdcr (uic2sr, 0x00000000);	/* clear all interrupts */
+	mtdcr (uic2sr, 0xffffffff);	/* clear all interrupts */
+
+	mtdcr (uic1sr, 0xffffffff);	/* Clear all interrupts*/
+	mtdcr (uic1er, 0x00000000);	/* disable all interrupts*/
+	mtdcr (uic1cr, 0x00000000);	/* Set Critical / Non Critical interrupts*/
+	mtdcr (uic1pr, 0xffffffff);	/* Set Interrupt Polarities */
+	mtdcr (uic1tr, 0x001f8040);	/* Set Interrupt Trigger Levels*/
+	mtdcr (uic1vr, 0x00000001);	/* Set Vect base=0,INT31 Highest priority */
+	mtdcr (uic1sr, 0x00000000);	/* clear all interrupts*/
+	mtdcr (uic1sr, 0xffffffff);	/* clear all interrupts*/
+
+	mtdcr (uic0sr, 0xffffffff);	/* Clear all interrupts */
+	mtdcr (uic0er, 0x00000000);	/* disable all interrupts excepted cascade    to be checked */
+	mtdcr (uic0cr, 0x00104001);	/* Set Critical / Non Critical interrupts*/
+	mtdcr (uic0pr, 0xffffffff);	/* Set Interrupt Polarities*/
+	mtdcr (uic0tr, 0x010f0004);	/* Set Interrupt Trigger Levels */
+	mtdcr (uic0vr, 0x00000001);	/* Set Vect base=0,INT31 Highest priority */
+	mtdcr (uic0sr, 0x00000000);	/* clear all interrupts*/
+	mtdcr (uic0sr, 0xffffffff);	/* clear all interrupts*/
+
+/* SDR0_MFR should be part of Ethernet init */
+	mfsdr (sdr_mfr, mfr);
+	mfr &= ~SDR0_MFR_ECS_MASK;
+/*	mtsdr(sdr_mfr, mfr); */
+
+	/*
+	 * Setup GPIO signalling per defines in katmai.h
+	 */
+	pfc = PFC0_KATMAI;
+	mtsdr(SDR0_PFC0, pfc);
+
+	out32(GPIO0_OR_ADDR, GPIO_OR_KATMAI);
+	out32(GPIO0_ODR_ADDR, GPIO_ODR_KATMAI);
+	out32(GPIO0_TCR_ADDR, GPIO_TCR_KATMAI);
+
+	return 0;
+}
+
+int checkboard (void)
+{
+	char *s = getenv("serial#");
+
+	printf("Board: Katmai - AMCC 440SPe Evaluation Board");
+	if (s != NULL) {
+		puts(", serial# ");
+		puts(s);
+	}
+	putc('\n');
+
+	return 0;
+}
+
+#if defined(CFG_DRAM_TEST)
+int testdram (void)
+{
+	uint *pstart = (uint *) 0x00000000;
+	uint *pend = (uint *) 0x08000000;
+	uint *p;
+
+	for (p = pstart; p < pend; p++)
+		*p = 0xaaaaaaaa;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0xaaaaaaaa) {
+			printf ("SDRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	for (p = pstart; p < pend; p++)
+		*p = 0x55555555;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0x55555555) {
+			printf ("SDRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+	return 0;
+}
+#endif
+
+/*************************************************************************
+ *  pci_pre_init
+ *
+ *  This routine is called just prior to registering the hose and gives
+ *  the board the opportunity to check things. Returning a value of zero
+ *  indicates that things are bad & PCI initialization should be aborted.
+ *
+ *	Different boards may wish to customize the pci controller structure
+ *	(add regions, override default access routines, etc) or perform
+ *	certain pre-initialization actions.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+int pci_pre_init(struct pci_controller * hose )
+{
+	unsigned long strap;
+
+	/*-------------------------------------------------------------------+
+	 *	The katmai board is always configured as the host & requires the
+	 *	PCI arbiter to be enabled.
+	 *-------------------------------------------------------------------*/
+	mfsdr(sdr_sdstp1, strap);
+	if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
+		printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
+		return 0;
+	}
+
+	return 1;
+}
+#endif	/* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+
+/*************************************************************************
+ *  pci_target_init
+ *
+ *	The bootstrap configuration provides default settings for the pci
+ *	inbound map (PIM). But the bootstrap config choices are limited and
+ *	may not be sufficient for a given board.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+void pci_target_init(struct pci_controller * hose )
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	/*-------------------------------------------------------------------+
+	 * Disable everything
+	 *-------------------------------------------------------------------*/
+	out32r( PCIX0_PIM0SA, 0 ); /* disable */
+	out32r( PCIX0_PIM1SA, 0 ); /* disable */
+	out32r( PCIX0_PIM2SA, 0 ); /* disable */
+	out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
+
+	/*-------------------------------------------------------------------+
+	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
+	 * strapping options to not support sizes such as 128/256 MB.
+	 *-------------------------------------------------------------------*/
+	out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE );
+	out32r( PCIX0_PIM0LAH, 0 );
+	out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
+	out32r( PCIX0_BAR0, 0 );
+
+	/*-------------------------------------------------------------------+
+	 * Program the board's subsystem id/vendor id
+	 *-------------------------------------------------------------------*/
+	out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
+	out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID );
+
+	out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
+}
+#endif	/* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+
+#if defined(CONFIG_PCI)
+/*************************************************************************
+ *  is_pci_host
+ *
+ *	This routine is called to determine if a pci scan should be
+ *	performed. With various hardware environments (especially cPCI and
+ *	PPMC) it's insufficient to depend on the state of the arbiter enable
+ *	bit in the strap register, or generic host/adapter assumptions.
+ *
+ *	Rather than hard-code a bad assumption in the general 440 code, the
+ *	440 pci code requires the board to decide at runtime.
+ *
+ *	Return 0 for adapter mode, non-zero for host (monarch) mode.
+ *
+ *
+ ************************************************************************/
+int is_pci_host(struct pci_controller *hose)
+{
+	/* The katmai board is always configured as host. */
+	return 1;
+}
+
+static struct pci_controller pcie_hose[3] = {{0},{0},{0}};
+
+void pcie_setup_hoses(void)
+{
+	struct pci_controller *hose;
+	int i, bus;
+
+	/*
+	 * assume we're called after the PCIX hose is initialized, which takes
+	 * bus ID 0 and therefore start numbering PCIe's from 1.
+	 */
+	bus = 1;
+	for (i = 0; i <= 2; i++) {
+#ifdef PCIE_ENDPOINT
+ 		if (ppc440spe_init_pcie_endport(i)) {
+#else
+		if (ppc440spe_init_pcie_rootport(i)) {
+#endif
+			printf("PCIE%d: initialization failed\n", i);
+			continue;
+		}
+
+		hose = &pcie_hose[i];
+		hose->first_busno = bus;
+		hose->last_busno  = bus;
+		bus++;
+
+		/* setup mem resource */
+		pci_set_region(hose->regions + 0,
+			       CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
+			       CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
+			       CFG_PCIE_MEMSIZE,
+			       PCI_REGION_MEM
+			);
+		hose->region_count = 1;
+		pci_register_hose(hose);
+
+#ifdef PCIE_ENDPOINT
+		ppc440spe_setup_pcie_endpoint(hose, i);
+		/*
+		 * Reson for no scanning is endpoint can not generate
+		 * upstream configuration accesses.
+		 */
+#else
+		ppc440spe_setup_pcie_rootpoint(hose, i);
+		/*
+		 * Config access can only go down stream
+		 */
+		hose->last_busno = pci_hose_scan(hose);
+#endif
+	}
+}
+#endif	/* defined(CONFIG_PCI) */
+
+int misc_init_f (void)
+{
+	uint reg;
+#if defined(CONFIG_STRESS)
+	uint i ;
+	uint disp;
+#endif
+
+	/* minimal init for PCIe */
+#if 0 /* test-only: test endpoint at some time, for now rootpoint only */
+	/* pci express 0 Endpoint Mode */
+	mfsdr(SDR0_PE0DLPSET, reg);
+	reg &= (~0x00400000);
+	mtsdr(SDR0_PE0DLPSET, reg);
+#else
+	/* pci express 0 Rootpoint  Mode */
+	mfsdr(SDR0_PE0DLPSET, reg);
+	reg |= 0x00400000;
+	mtsdr(SDR0_PE0DLPSET, reg);
+#endif
+	/* pci express 1 Rootpoint  Mode */
+	mfsdr(SDR0_PE1DLPSET, reg);
+	reg |= 0x00400000;
+	mtsdr(SDR0_PE1DLPSET, reg);
+	/* pci express 2 Rootpoint  Mode */
+	mfsdr(SDR0_PE2DLPSET, reg);
+	reg |= 0x00400000;
+	mtsdr(SDR0_PE2DLPSET, reg);
+
+#if defined(CONFIG_STRESS)
+	/*
+	 * All this setting done by linux only needed by stress an charac. test
+	 * procedure
+	 * PCIe 1 Rootpoint PCIe2 Endpoint
+	 * PCIe 0 FIR Pre-emphasis Filter Coefficients & Transmit Driver Power Level
+	 */
+	for (i=0,disp=0; i<8; i++,disp+=3) {
+		mfsdr(SDR0_PE0HSSSET1L0+disp, reg);
+		reg |= 0x33000000;
+		mtsdr(SDR0_PE0HSSSET1L0+disp, reg);
+	}
+
+	/*PCIe 1 FIR Pre-emphasis Filter Coefficients & Transmit Driver Power Level */
+	for (i=0,disp=0; i<4; i++,disp+=3) {
+		mfsdr(SDR0_PE1HSSSET1L0+disp, reg);
+		reg |= 0x33000000;
+		mtsdr(SDR0_PE1HSSSET1L0+disp, reg);
+	}
+
+	/*PCIE 2 FIR Pre-emphasis Filter Coefficients & Transmit Driver Power Level */
+	for (i=0,disp=0; i<4; i++,disp+=3) {
+		mfsdr(SDR0_PE2HSSSET1L0+disp, reg);
+		reg |= 0x33000000;
+		mtsdr(SDR0_PE2HSSSET1L0+disp, reg);
+	}
+
+	reg = 0x21242222;
+	mtsdr(SDR0_PE2UTLSET1, reg);
+	reg = 0x11000000;
+	mtsdr(SDR0_PE2UTLSET2, reg);
+	/* pci express 1 Endpoint  Mode */
+	reg = 0x00004000;
+	mtsdr(SDR0_PE2DLPSET, reg);
+
+	mtsdr(SDR0_UART1, 0x2080005a);	/* patch for TG */
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_POST
+/*
+ * Returns 1 if keys pressed to start the power-on long-running tests
+ * Called from board_init_f().
+ */
+int post_hotkeys_pressed(void)
+{
+	return (ctrlc());
+}
+#endif
diff --git a/board/amcc/katmai/katmai.h b/board/amcc/katmai/katmai.h
new file mode 100644
index 0000000000..9d5b793f13
--- /dev/null
+++ b/board/amcc/katmai/katmai.h
@@ -0,0 +1,65 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __KATMAI_H_
+#define __KATMAI_H_
+
+/*----------------------------------------------------------------------------
+ *                    XX
+ *   XXXX    XX XXX   XXX     XXXX
+ * XX        XX  XX   XX    XX  XX
+ * XX  XXX   XX  XX   XX    XX  XX
+ * XX  XX    XXXXX    XX    XX  XX
+ *  XXXX     XX      XXXX    XXXX
+ *          XXXX
+ *
+ *  The 440SPe provices 32 bits of GPIO.  By default all GPIO pins
+ *  are disabled, and must be explicitly enabled by setting a
+ *  bit in the SDR0_PFC0 indirect DCR.  Each GPIO maps 1-to-1 with the
+ *  corresponding bit in the SDR0_PFC0 register (note that bit numbers
+ *  reflect the PowerPC convention where bit 0 is the most-significant
+ *  bit).
+ *
+ *   Katmai specific:
+ *      RS232_RX_EN# is held HIGH during reset by hardware, keeping the
+ *      RS232_CTS, DSR & DCD  signals coming from the MAX3411 (U26) in
+ *      Hi-Z condition. This prevents contention between the MAX3411 (U26)
+ *      and 74CBTLV3125PG (U2) during reset.
+ *
+ *      RS232_RX_EN# is connected as GPIO pin 30.  Once the processor
+ *      is released from reset, this pin must be configured as an output and
+ *      then driven high to enable the receive signals from the UART transciever.
+ *----------------------------------------------------------------------------*/
+#define GPIO_ENABLE(gpio)       (0x80000000 >> (gpio))
+
+#define PFC0_KATMAI             GPIO_ENABLE(30)
+#define GPIO_OR_KATMAI          GPIO_ENABLE(30)     /* Drive all outputs low except GPIO 30 */
+#define GPIO_TCR_KATMAI         GPIO_ENABLE(30)
+#define GPIO_ODR_KATMAI         0                   /* Disable open drain for all outputs */
+
+#define GPIO0_OR_ADDR           (CFG_PERIPHERAL_BASE + 0x700)
+#define GPIO0_TCR_ADDR          (CFG_PERIPHERAL_BASE + 0x704)
+#define GPIO0_ODR_ADDR          (CFG_PERIPHERAL_BASE + 0x718)
+#define GPIO0_IR_ADDR           (CFG_PERIPHERAL_BASE + 0x71C)
+
+#endif /* __KATMAI_H_ */
diff --git a/board/amcc/katmai/u-boot.lds b/board/amcc/katmai/u-boot.lds
new file mode 100644
index 0000000000..bf8fc5d3da
--- /dev/null
+++ b/board/amcc/katmai/u-boot.lds
@@ -0,0 +1,141 @@
+/*
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/ppc4xx/start.o	(.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)	}
+  .rela.text     : { *(.rela.text)	}
+  .rel.data      : { *(.rel.data)	}
+  .rela.data     : { *(.rela.data)	}
+  .rel.rodata    : { *(.rel.rodata)	}
+  .rela.rodata   : { *(.rela.rodata)	}
+  .rel.got       : { *(.rel.got)	}
+  .rela.got      : { *(.rela.got)	}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)	}
+  .rela.bss      : { *(.rela.bss)	}
+  .rel.plt       : { *(.rel.plt)	}
+  .rela.plt      : { *(.rela.plt)	}
+  .init          : { *(.init)		}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/ppc4xx/start.o		(.text)
+    board/amcc/katmai/init.o	(.text)
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
diff --git a/board/cray/L1/L1.c b/board/cray/L1/L1.c
index a7114eb074..a0fac7fe5a 100644
--- a/board/cray/L1/L1.c
+++ b/board/cray/L1/L1.c
@@ -23,7 +23,7 @@
 
 #include <common.h>
 #include <asm/processor.h>
-#include <405gp_i2c.h>
+#include <4xx_i2c.h>
 #include <command.h>
 #include <rtc.h>
 #include <post.h>
diff --git a/board/esd/common/auto_update.c b/board/esd/common/auto_update.c
index 5cd342332f..001fd68da4 100644
--- a/board/esd/common/auto_update.c
+++ b/board/esd/common/auto_update.c
@@ -33,6 +33,7 @@
 #include <asm/byteorder.h>
 #include <linux/mtd/nand_legacy.h>
 #include <fat.h>
+#include <part.h>
 
 #include "auto_update.h"
 
@@ -71,8 +72,6 @@ extern int transfer_pic(unsigned char, unsigned char *, int, int);
 extern int flash_sect_erase(ulong, ulong);
 extern int flash_sect_protect (int, ulong, ulong);
 extern int flash_write (char *, ulong, ulong);
-/* change char* to void* to shutup the compiler */
-extern block_dev_desc_t *get_dev (char*, int);
 
 #if (CONFIG_COMMANDS & CFG_CMD_NAND) && defined(CFG_NAND_LEGACY)
 /* references to names in cmd_nand.c */
diff --git a/board/esd/cpci750/cpci750.c b/board/esd/cpci750/cpci750.c
index 36bb7ce2c7..17e3568941 100644
--- a/board/esd/cpci750/cpci750.c
+++ b/board/esd/cpci750/cpci750.c
@@ -366,12 +366,12 @@ int misc_init_r ()
 	dcache_lock ();
 #endif
 	if (flash_info[3].size < CFG_FLASH_INCREMENT) {
-	        unsigned int flash_offset;
+		unsigned int flash_offset;
 		unsigned int l;
 
 		flash_offset =  CFG_FLASH_INCREMENT - flash_info[3].size;
 		for (l = 0; l < CFG_MAX_FLASH_SECT; l++) {
-		        if (flash_info[3].start[l] != 0) {
+			if (flash_info[3].start[l] != 0) {
 			      flash_info[3].start[l] += flash_offset;
 			}
 		}
@@ -503,7 +503,7 @@ static void move64 (unsigned long long *src, unsigned long long *dest)
 {
 	asm ("lfd  0, 0(3)\n\t"	/* fpr0   =  *scr       */
 	     "stfd 0, 0(4)"	/* *dest  =  fpr0       */
-      : : : "fr0");		/* Clobbers fr0         */
+      : : : "fr0");		/* Clobbers fr0		*/
 	return;
 }
 
@@ -581,9 +581,9 @@ int mem_test_data (void)
 		move64 (&(pattern[i]), pmem);
 		move64 (pmem, &temp64);
 
-		/* hi = (temp64>>32) & 0xffffffff;          */
-		/* lo = temp64 & 0xffffffff;                */
-		/* printf("\ntemp64 = 0x%08x%08x", hi, lo); */
+		/* hi = (temp64>>32) & 0xffffffff;		*/
+		/* lo = temp64 & 0xffffffff;			*/
+		/* printf("\ntemp64 = 0x%08x%08x", hi, lo);	*/
 
 		hi = (pattern[i] >> 32) & 0xffffffff;
 		lo = pattern[i] & 0xffffffff;
@@ -856,11 +856,11 @@ int testdram (void)
 }
 #endif /* CFG_DRAM_TEST */
 
-/* ronen - the below functions are used by the bootm function           */
+/* ronen - the below functions are used by the bootm function		*/
 /*  - we map the base register to fbe00000 (same mapping as in the LSP) */
 /*  - we turn off the RX gig dmas - to prevent the dma from overunning  */
-/*    the kernel data areas.                                            */
-/*  - we diable and invalidate the icache and dcache.                   */
+/*    the kernel data areas.						*/
+/*  - we diable and invalidate the icache and dcache.			*/
 void my_remap_gt_regs_bootm (u32 cur_loc, u32 new_loc)
 {
 	u32 temp;
@@ -911,13 +911,11 @@ int do_show_cfg(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
 	GT_REG_READ(0x3d4, &reset_sample_high);
 	printf("Reset configuration 0x%08x 0x%08x\n", reset_sample_low, reset_sample_high);
 
-        return(0);
+	return(0);
 }
 
-
 U_BOOT_CMD(
 	show_cfg,	1,	1,	do_show_cfg,
 	"show_cfg- Show Marvell strapping register\n",
 	"Show Marvell strapping register (ResetSampleLow ResetSampleHigh)\n"
 	);
-
diff --git a/board/esd/du405/du405.c b/board/esd/du405/du405.c
index a019ce4215..69432138d3 100644
--- a/board/esd/du405/du405.c
+++ b/board/esd/du405/du405.c
@@ -25,7 +25,7 @@
 #include "du405.h"
 #include <asm/processor.h>
 #include <ppc4xx.h>
-#include <405gp_i2c.h>
+#include <4xx_i2c.h>
 #include <command.h>
 
 DECLARE_GLOBAL_DATA_PTR;
diff --git a/board/lpc2292sodimm/lpc2292sodimm.c b/board/lpc2292sodimm/lpc2292sodimm.c
index de04c66385..d212c63328 100644
--- a/board/lpc2292sodimm/lpc2292sodimm.c
+++ b/board/lpc2292sodimm/lpc2292sodimm.c
@@ -46,7 +46,7 @@ int board_init (void)
 	gd->bd->bi_arch_number = 83;
 
 	/* location of boot parameters */
-	gd->bd->bi_boot_params = 0xc0000100;
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 
 	return 0;
 }
diff --git a/board/mcc200/auto_update.c b/board/mcc200/auto_update.c
index f1bb721284..90d03ec47a 100644
--- a/board/mcc200/auto_update.c
+++ b/board/mcc200/auto_update.c
@@ -23,6 +23,7 @@
 #include <image.h>
 #include <asm/byteorder.h>
 #include <usb.h>
+#include <part.h>
 
 #ifdef CFG_HUSH_PARSER
 #include <hush.h>
@@ -47,25 +48,6 @@
 #error "must define CFG_CMD_FAT"
 #endif
 
-/*
- * Check whether a USB memory stick is plugged in.
- * If one is found:
- *	1) if prepare.img ist found load it into memory. If it is
- *		valid then run it.
- *	2) if preinst.img is found load it into memory. If it is
- *		valid then run it. Update the EEPROM.
- *	3) if firmw_01.img is found load it into memory. If it is valid,
- *		burn it into FLASH and update the EEPROM.
- *	4) if kernl_01.img is found load it into memory. If it is valid,
- *		burn it into FLASH and update the EEPROM.
- *	5) if app.img is found load it into memory. If it is valid,
- *		burn it into FLASH and update the EEPROM.
- *	6) if disk.img is found load it into memory. If it is valid,
- *		burn it into FLASH and update the EEPROM.
- *	7) if postinst.img is found load it into memory. If it is
- *		valid then run it. Update the EEPROM.
- */
-
 #undef AU_DEBUG
 
 #undef debug
@@ -78,6 +60,7 @@
 /* possible names of files on the USB stick. */
 #define AU_FIRMWARE	"u-boot.img"
 #define AU_KERNEL	"kernel.img"
+#define AU_ROOTFS	"rootfs.img"
 
 struct flash_layout {
 	long start;
@@ -89,33 +72,47 @@ struct flash_layout {
 #define AU_FL_FIRMWARE_ND	0xfC03FFFF
 #define AU_FL_KERNEL_ST		0xfC0C0000
 #define AU_FL_KERNEL_ND		0xfC1BFFFF
+#define AU_FL_ROOTFS_ST		0xFC1C0000
+#define AU_FL_ROOTFS_ND		0xFCFBFFFF
 
 static int au_usb_stor_curr_dev; /* current device */
 
 /* index of each file in the following arrays */
 #define IDX_FIRMWARE	0
 #define IDX_KERNEL	1
+#define IDX_ROOTFS	2
 
 /* max. number of files which could interest us */
-#define AU_MAXFILES 2
+#define AU_MAXFILES 3
 
 /* pointers to file names */
-char *aufile[AU_MAXFILES];
+char *aufile[AU_MAXFILES] = {
+	AU_FIRMWARE,
+	AU_KERNEL,
+	AU_ROOTFS
+};
 
 /* sizes of flash areas for each file */
-long ausize[AU_MAXFILES];
+long ausize[AU_MAXFILES] = {
+	(AU_FL_FIRMWARE_ND + 1) - AU_FL_FIRMWARE_ST,
+	(AU_FL_KERNEL_ND   + 1) - AU_FL_KERNEL_ST,
+	(AU_FL_ROOTFS_ND   + 1) - AU_FL_ROOTFS_ST,
+};
 
 /* array of flash areas start and end addresses */
-struct flash_layout aufl_layout[AU_MAXFILES] = { \
-	{AU_FL_FIRMWARE_ST, AU_FL_FIRMWARE_ND,}, \
-	{AU_FL_KERNEL_ST, AU_FL_KERNEL_ND,}, \
+struct flash_layout aufl_layout[AU_MAXFILES] = {
+	{ AU_FL_FIRMWARE_ST,	AU_FL_FIRMWARE_ND, },
+	{ AU_FL_KERNEL_ST,	AU_FL_KERNEL_ND,   },
+	{ AU_FL_ROOTFS_ST,	AU_FL_ROOTFS_ND,   },
 };
 
+ulong totsize;
+
 /* where to load files into memory */
 #define LOAD_ADDR ((unsigned char *)0x00200000)
 
-/* the app is the largest image */
-#define MAX_LOADSZ ausize[IDX_KERNEL]
+/* the root file system is the largest image */
+#define MAX_LOADSZ ausize[IDX_ROOTFS]
 
 /*i2c address of the keypad status*/
 #define I2C_PSOC_KEYPAD_ADDR	0x53
@@ -134,9 +131,12 @@ extern int i2c_read (unsigned char, unsigned int, int , unsigned char* , int);
 extern int flash_sect_erase(ulong, ulong);
 extern int flash_sect_protect (int, ulong, ulong);
 extern int flash_write (char *, ulong, ulong);
-/* change char* to void* to shutup the compiler */
-extern block_dev_desc_t *get_dev (char*, int);
 extern int u_boot_hush_start(void);
+#ifdef CONFIG_PROGRESSBAR
+extern void show_progress(int, int);
+extern void lcd_puts (char *);
+extern void lcd_enable(void);
+#endif
 
 int au_check_cksum_valid(int idx, long nbytes)
 {
@@ -162,8 +162,7 @@ int au_check_cksum_valid(int idx, long nbytes)
 int au_check_header_valid(int idx, long nbytes)
 {
 	image_header_t *hdr;
-	unsigned long checksum;
-	unsigned char buf[4];
+	unsigned long checksum, fsize;
 
 	hdr = (image_header_t *)LOAD_ADDR;
 	/* check the easy ones first */
@@ -176,10 +175,12 @@ int au_check_header_valid(int idx, long nbytes)
 #endif
 	if (nbytes < sizeof(*hdr)) {
 		printf ("Image %s bad header SIZE\n", aufile[idx]);
+		ausize[idx] = 0;
 		return -1;
 	}
 	if (ntohl(hdr->ih_magic) != IH_MAGIC || hdr->ih_arch != IH_CPU_PPC) {
 		printf ("Image %s bad MAGIC or ARCH\n", aufile[idx]);
+		ausize[idx] = 0;
 		return -1;
 	}
 	/* check the hdr CRC */
@@ -188,30 +189,46 @@ int au_check_header_valid(int idx, long nbytes)
 
 	if (crc32 (0, (uchar *)hdr, sizeof(*hdr)) != checksum) {
 		printf ("Image %s bad header checksum\n", aufile[idx]);
+		ausize[idx] = 0;
 		return -1;
 	}
 	hdr->ih_hcrc = htonl(checksum);
 	/* check the type - could do this all in one gigantic if() */
 	if ((idx == IDX_FIRMWARE) && (hdr->ih_type != IH_TYPE_FIRMWARE)) {
 		printf ("Image %s wrong type\n", aufile[idx]);
+		ausize[idx] = 0;
 		return -1;
 	}
 	if ((idx == IDX_KERNEL) && (hdr->ih_type != IH_TYPE_KERNEL)) {
 		printf ("Image %s wrong type\n", aufile[idx]);
+		ausize[idx] = 0;
+		return -1;
+	}
+	if ((idx == IDX_ROOTFS) &&
+		( (hdr->ih_type != IH_TYPE_RAMDISK) && (hdr->ih_type != IH_TYPE_FILESYSTEM) )
+	   ) {
+		printf ("Image %s wrong type\n", aufile[idx]);
+		ausize[idx] = 0;
 		return -1;
 	}
 	/* recycle checksum */
 	checksum = ntohl(hdr->ih_size);
-	/* for kernel and app the image header must also fit into flash */
-	if (idx != IDX_FIRMWARE)
+
+	fsize = checksum + sizeof(*hdr);
+	/* for kernel and ramdisk the image header must also fit into flash */
+	if (idx == IDX_KERNEL || hdr->ih_type == IH_TYPE_RAMDISK)
 		checksum += sizeof(*hdr);
+
 	/* check the size does not exceed space in flash. HUSH scripts */
-	/* all have ausize[] set to 0 */
 	if ((ausize[idx] != 0) && (ausize[idx] < checksum)) {
 		printf ("Image %s is bigger than FLASH\n", aufile[idx]);
+		ausize[idx] = 0;
 		return -1;
 	}
-	return 0;
+	/* Update with the real filesize */
+	ausize[idx] = fsize;
+
+	return checksum; /* return size to be written to flash */
 }
 
 int au_do_update(int idx, long sz)
@@ -256,8 +273,12 @@ int au_do_update(int idx, long sz)
 	debug ("flash_sect_erase(%lx, %lx);\n", start, end);
 	flash_sect_erase(start, end);
 	wait_ms(100);
+#ifdef CONFIG_PROGRESSBAR
+	show_progress(end - start, totsize);
+#endif
+
 	/* strip the header - except for the kernel and ramdisk */
-	if (hdr->ih_type == IH_TYPE_KERNEL) {
+	if (hdr->ih_type == IH_TYPE_KERNEL || hdr->ih_type == IH_TYPE_RAMDISK) {
 		addr = (char *)hdr;
 		off = sizeof(*hdr);
 		nbytes = sizeof(*hdr) + ntohl(hdr->ih_size);
@@ -280,9 +301,13 @@ int au_do_update(int idx, long sz)
 		return -1;
 	}
 
-	/* check the dcrc of the copy */
+#ifdef CONFIG_PROGRESSBAR
+	show_progress(nbytes, totsize);
+#endif
+
+	/* check the data CRC of the copy */
 	if (crc32 (0, (uchar *)(start + off), ntohl(hdr->ih_size)) != ntohl(hdr->ih_dcrc)) {
-		printf ("Image %s Bad Data Checksum After COPY\n", aufile[idx]);
+		printf ("Image %s Bad Data Checksum after COPY\n", aufile[idx]);
 		return -1;
 	}
 
@@ -302,10 +327,10 @@ int do_auto_update(void)
 {
 	block_dev_desc_t *stor_dev;
 	long sz;
-	int i, res, bitmap_first, cnt, old_ctrlc, got_ctrlc;
+	int i, res = 0, bitmap_first, cnt, old_ctrlc, got_ctrlc;
 	char *env;
 	long start, end;
-	char keypad_status1[2] = {0,0}, keypad_status2[2] = {0,0};
+	uchar keypad_status1[2] = {0,0}, keypad_status2[2] = {0,0};
 
 	/*
 	 * Read keypad status
@@ -317,14 +342,11 @@ int do_auto_update(void)
 	/*
 	 * Check keypad
 	 */
-	if ( !(keypad_status1[0] & KEYPAD_MASK_HI) ||
-	      (keypad_status1[0] != keypad_status2[0])) {
-		return 0;
-	}
 	if ( !(keypad_status1[1] & KEYPAD_MASK_LO) ||
 	      (keypad_status1[1] != keypad_status2[1])) {
 		return 0;
 	}
+
 	au_usb_stor_curr_dev = -1;
 	/* start USB */
 	if (usb_stop() < 0) {
@@ -359,14 +381,6 @@ int do_auto_update(void)
 		debug ("file_fat_detectfs failed\n");
 	}
 
-	/* initialize the array of file names */
-	memset(aufile, 0, sizeof(aufile));
-	aufile[IDX_FIRMWARE] = AU_FIRMWARE;
-	aufile[IDX_KERNEL] = AU_KERNEL;
-	/* initialize the array of flash sizes */
-	memset(ausize, 0, sizeof(ausize));
-	ausize[IDX_FIRMWARE] = (AU_FL_FIRMWARE_ND + 1) - AU_FL_FIRMWARE_ST;
-	ausize[IDX_KERNEL] = (AU_FL_KERNEL_ND + 1) - AU_FL_KERNEL_ST;
 	/*
 	 * now check whether start and end are defined using environment
 	 * variables.
@@ -381,8 +395,8 @@ int do_auto_update(void)
 		end = simple_strtoul(env, NULL, 16);
 	if (start >= 0 && end && end > start) {
 		ausize[IDX_FIRMWARE] = (end + 1) - start;
-		aufl_layout[0].start = start;
-		aufl_layout[0].end = end;
+		aufl_layout[IDX_FIRMWARE].start = start;
+		aufl_layout[IDX_FIRMWARE].end = end;
 	}
 	start = -1;
 	end = 0;
@@ -394,32 +408,73 @@ int do_auto_update(void)
 		end = simple_strtoul(env, NULL, 16);
 	if (start >= 0 && end && end > start) {
 		ausize[IDX_KERNEL] = (end + 1) - start;
-		aufl_layout[1].start = start;
-		aufl_layout[1].end = end;
+		aufl_layout[IDX_KERNEL].start = start;
+		aufl_layout[IDX_KERNEL].end = end;
 	}
+	start = -1;
+	end = 0;
+	env = getenv("rootfs_st");
+	if (env != NULL)
+		start = simple_strtoul(env, NULL, 16);
+	env = getenv("rootfs_nd");
+	if (env != NULL)
+		end = simple_strtoul(env, NULL, 16);
+	if (start >= 0 && end && end > start) {
+		ausize[IDX_ROOTFS] = (end + 1) - start;
+		aufl_layout[IDX_ROOTFS].start = start;
+		aufl_layout[IDX_ROOTFS].end = end;
+	}
+
 	/* make certain that HUSH is runnable */
 	u_boot_hush_start();
 	/* make sure that we see CTRL-C and save the old state */
 	old_ctrlc = disable_ctrlc(0);
 
 	bitmap_first = 0;
-	/* just loop thru all the possible files */
+
+	/* validate the images first */
 	for (i = 0; i < AU_MAXFILES; i++) {
+		ulong imsize;
 		/* just read the header */
 		sz = file_fat_read(aufile[i], LOAD_ADDR, sizeof(image_header_t));
 		debug ("read %s sz %ld hdr %d\n",
 			aufile[i], sz, sizeof(image_header_t));
 		if (sz <= 0 || sz < sizeof(image_header_t)) {
 			debug ("%s not found\n", aufile[i]);
+			ausize[i] = 0;
 			continue;
 		}
-		if (au_check_header_valid(i, sz) < 0) {
+		/* au_check_header_valid() updates ausize[] */
+		if ((imsize = au_check_header_valid(i, sz)) < 0) {
 			debug ("%s header not valid\n", aufile[i]);
 			continue;
 		}
-		sz = file_fat_read(aufile[i], LOAD_ADDR, MAX_LOADSZ);
+		/* totsize accounts for image size and flash erase size */
+		totsize += (imsize + (aufl_layout[i].end - aufl_layout[i].start));
+	}
+
+#ifdef CONFIG_PROGRESSBAR
+	if (totsize) {
+		lcd_puts(" Update in progress\n");
+		lcd_enable();
+	}
+#endif
+
+	/* just loop thru all the possible files */
+	for (i = 0; i < AU_MAXFILES && totsize; i++) {
+		if (!ausize[i]) {
+			continue;
+		}
+		sz = file_fat_read(aufile[i], LOAD_ADDR, ausize[i]);
+
 		debug ("read %s sz %ld hdr %d\n",
 			aufile[i], sz, sizeof(image_header_t));
+
+		if (sz != ausize[i]) {
+			printf ("%s: size %d read %d?\n", aufile[i], ausize[i], sz);
+			continue;
+		}
+
 		if (sz <= 0 || sz <= sizeof(image_header_t)) {
 			debug ("%s not found\n", aufile[i]);
 			continue;
@@ -443,8 +498,8 @@ int do_auto_update(void)
 			}
 			cnt++;
 #ifdef AU_TEST_ONLY
-		} while (res < 0 && cnt < 3);
-		if (cnt < 3)
+		} while (res < 0 && cnt < (AU_MAXFILES + 1));
+		if (cnt < (AU_MAXFILES + 1))
 #else
 		} while (res < 0);
 #endif
@@ -452,6 +507,16 @@ int do_auto_update(void)
 	usb_stop();
 	/* restore the old state */
 	disable_ctrlc(old_ctrlc);
+#ifdef CONFIG_PROGRESSBAR
+	if (totsize) {
+		if (!res) {
+			lcd_puts("\n  Update completed\n");
+		} else {
+			lcd_puts("\n   Update error\n");
+		}
+		lcd_enable();
+	}
+#endif
 	return 0;
 }
 #endif /* CONFIG_AUTO_UPDATE */
diff --git a/board/mcc200/lcd.c b/board/mcc200/lcd.c
index b2625160a5..98b86d1834 100644
--- a/board/mcc200/lcd.c
+++ b/board/mcc200/lcd.c
@@ -24,13 +24,13 @@
 
 #ifdef CONFIG_LCD
 
-#define SWAPPED_LCD
+#undef SWAPPED_LCD /* For the previous h/w version */
 /*
  *  The name of the device used for communication
  * with the PSoC.
  */
 #define PSOC_PSC	MPC5XXX_PSC2
-#define PSOC_BAUD	500000UL
+#define PSOC_BAUD	230400UL
 
 #define RTS_ASSERT	1
 #define RTS_NEGATE	0
@@ -181,10 +181,35 @@ void lcd_enable (void)
 		udelay (PSOC_WAIT_TIME);
 	}
 	if (!retries) {
-		printf ("%s Error: PSoC doesn't respond on "
+		printf ("%s Warning: PSoC doesn't respond on "
 			"RTS NEGATE\n",	__FUNCTION__);
 	}
 
 	return;
 }
+#ifdef CONFIG_PROGRESSBAR
+
+#define FONT_WIDTH      8 /* the same as VIDEO_FONT_WIDTH in video_font.h */
+void show_progress (int size, int tot)
+{
+	int cnt;
+	int i;
+	static int rc = 0;
+
+	rc += size;
+
+	cnt = ((LCD_WIDTH/FONT_WIDTH) * rc) / tot;
+
+	rc -= (cnt * tot) / (LCD_WIDTH/FONT_WIDTH);
+
+	for (i = 0; i < cnt; i++) {
+		lcd_putc(0xdc);
+	}
+
+	if (cnt) {
+		lcd_enable(); /* MCC200-specific - send the framebuffer to PSoC */
+	}
+}
+
+#endif
 #endif /* CONFIG_LCD */
diff --git a/board/motionpro/Makefile b/board/motionpro/Makefile
new file mode 100644
index 0000000000..698ead195c
--- /dev/null
+++ b/board/motionpro/Makefile
@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2003-2007
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= $(BOARD).o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/motionpro/config.mk b/board/motionpro/config.mk
new file mode 100644
index 0000000000..e7934d29c1
--- /dev/null
+++ b/board/motionpro/config.mk
@@ -0,0 +1,30 @@
+#
+# (C) Copyright 2006-2007
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# Promess Motion-PRO
+#
+
+TEXT_BASE = 0xfff00000
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR)/board
diff --git a/board/motionpro/motionpro.c b/board/motionpro/motionpro.c
new file mode 100644
index 0000000000..d60d23332b
--- /dev/null
+++ b/board/motionpro/motionpro.c
@@ -0,0 +1,172 @@
+/*
+ * (C) Copyright 2003-2007
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * modified for Promess PRO - by Andy Joseph, andy@promessdev.com
+ * modified for Promess PRO-Motion - by Robert McCullough, rob@promessdev.com
+ * modified by Chris M. Tumas 6/20/06 Change CAS latency to 2 from 3
+ * Also changed the refresh for 100Mhz operation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc5xxx.h>
+
+
+/* Kollmorgen DPR initialization data */
+struct init_elem {
+	unsigned long addr;
+	unsigned len;
+	char *data;
+	} init_seq[] = {
+		{0x500003F2, 2, "\x86\x00"},		/* HW parameter */
+		{0x500003F0, 2, "\x00\x00"},
+		{0x500003EC, 4, "\x00\x80\xc1\x52"},	/* Magic word */
+	};
+
+/*
+ * Initialize Kollmorgen DPR
+ */
+static void kollmorgen_init(void)
+{
+	unsigned i, j;
+	vu_char *p;
+
+	for (i = 0; i < sizeof(init_seq) / sizeof(struct init_elem); ++i) {
+		p = (vu_char *)init_seq[i].addr;
+		for (j = 0; j < init_seq[i].len; ++j)
+			*(p + j) = *(init_seq[i].data + j);
+	}
+
+	printf("DPR:   Kollmorgen DPR initialized\n");
+}
+
+
+/*
+ * Early board initalization.
+ */
+int board_early_init_r(void)
+{
+	/* Now, when we are in RAM, disable Boot Chipselect and enable CS0 */
+	*(vu_long *)MPC5XXX_ADDECR &= ~(1 << 25);
+	*(vu_long *)MPC5XXX_ADDECR |= (1 << 16);
+
+	/* Initialize Kollmorgen DPR */
+	kollmorgen_init();
+
+	return 0;
+}
+
+
+#ifndef CFG_RAMBOOT
+/*
+ * Helper function to initialize SDRAM controller.
+ */
+static void sdram_start (int hi_addr)
+{
+	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
+
+	/* unlock mode register */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 |
+						hi_addr_bit;
+
+	/* precharge all banks */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 |
+						hi_addr_bit;
+
+	/* auto refresh */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 |
+						hi_addr_bit;
+
+	/* auto refresh, second time */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 |
+						hi_addr_bit;
+
+	/* set mode register */
+	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE;
+
+	/* normal operation */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
+}
+#endif /* !CFG_RAMBOOT */
+
+
+/*
+ * Initalize SDRAM - configure SDRAM controller, detect memory size.
+ */
+long int initdram (int board_type)
+{
+	ulong dramsize = 0;
+#ifndef CFG_RAMBOOT
+	ulong test1, test2;
+
+	/* configure SDRAM start/end for detection */
+	*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001e; /* 2G at 0x0 */
+	*(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x80000000; /* disabled */
+
+	/* setup config registers */
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
+
+	sdram_start(0);
+	test1 = get_ram_size((long *)CFG_SDRAM_BASE, 0x80000000);
+	sdram_start(1);
+	test2 = get_ram_size((long *)CFG_SDRAM_BASE, 0x80000000);
+	if (test1 > test2) {
+		sdram_start(0);
+		dramsize = test1;
+	} else {
+		dramsize = test2;
+	}
+
+	/* memory smaller than 1MB is impossible */
+	if (dramsize < (1 << 20))
+		dramsize = 0;
+
+	/* set SDRAM CS0 size according to the amount of RAM found */
+	if (dramsize > 0) {
+		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 +
+			__builtin_ffs(dramsize >> 20) - 1;
+	} else {
+		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
+	}
+
+	/* let SDRAM CS1 start right after CS0 and disable it */
+	*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize;
+
+#else /* !CFG_RAMBOOT */
+	/* retrieve size of memory connected to SDRAM CS0 */
+	dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
+	if (dramsize >= 0x13)
+		dramsize = (1 << (dramsize - 0x13)) << 20;
+	else
+		dramsize = 0;
+#endif /* CFG_RAMBOOT */
+
+	/* return total ram size */
+	return dramsize;
+}
+
+
+int checkboard (void)
+{
+	puts("Board: Promess Motion-PRO board\n");
+	return 0;
+}
diff --git a/board/motionpro/u-boot.lds b/board/motionpro/u-boot.lds
new file mode 100644
index 0000000000..8fa9c0f7ed
--- /dev/null
+++ b/board/motionpro/u-boot.lds
@@ -0,0 +1,123 @@
+/*
+ * (C) Copyright 2003-2007
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc5xxx/start.o	(.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+    . = ALIGN(16);
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(4096);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(4096);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
diff --git a/board/mpl/common/memtst.c b/board/mpl/common/memtst.c
index ff1190ab21..1d28513d87 100644
--- a/board/mpl/common/memtst.c
+++ b/board/mpl/common/memtst.c
@@ -48,7 +48,7 @@ int testdram (void)
 
 #include <common.h>
 #include <asm/processor.h>
-#include <405gp_i2c.h>
+#include <4xx_i2c.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
diff --git a/board/mpl/mip405/mip405.c b/board/mpl/mip405/mip405.c
index 34f328999d..4b1c1c0669 100644
--- a/board/mpl/mip405/mip405.c
+++ b/board/mpl/mip405/mip405.c
@@ -65,7 +65,7 @@
 #include <common.h>
 #include "mip405.h"
 #include <asm/processor.h>
-#include <405gp_i2c.h>
+#include <4xx_i2c.h>
 #include <miiphy.h>
 #include "../common/common_util.h"
 #include <i2c.h>
@@ -73,9 +73,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-extern block_dev_desc_t * scsi_get_dev(int dev);
-extern block_dev_desc_t * ide_get_dev(int dev);
-
 #undef SDRAM_DEBUG
 #define ENABLE_ECC /* for ecc boards */
 #define FALSE           0
diff --git a/board/prodrive/p3mx/p3mx.h b/board/prodrive/p3mx/p3mx.h
index 91071e9209..1caae6b9c1 100644
--- a/board/prodrive/p3mx/p3mx.h
+++ b/board/prodrive/p3mx/p3mx.h
@@ -31,4 +31,3 @@
 #define LED_ORANGE	4
 
 #endif /* __P3MX_H__ */
-
diff --git a/board/sandburst/common/ppc440gx_i2c.c b/board/sandburst/common/ppc440gx_i2c.c
index 859dd7afe5..1e3dffb1ee 100644
--- a/board/sandburst/common/ppc440gx_i2c.c
+++ b/board/sandburst/common/ppc440gx_i2c.c
@@ -27,13 +27,8 @@
  */
 #include <common.h>
 #include <ppc4xx.h>
-#if defined(CONFIG_440)
-#   include <440_i2c.h>
-#else
-#   include <405gp_i2c.h>
-#endif
+#include <4xx_i2c.h>
 #include <i2c.h>
-#include <440_i2c.h>
 #include <command.h>
 #include "ppc440gx_i2c.h"
 
diff --git a/board/sandburst/common/ppc440gx_i2c.h b/board/sandburst/common/ppc440gx_i2c.h
index cd4fc86661..10000f5ba9 100644
--- a/board/sandburst/common/ppc440gx_i2c.h
+++ b/board/sandburst/common/ppc440gx_i2c.h
@@ -27,11 +27,7 @@
  */
 #include <common.h>
 #include <ppc4xx.h>
-#if defined(CONFIG_440)
-#   include <440_i2c.h>
-#else
-#   include <405gp_i2c.h>
-#endif
+#include <4xx_i2c.h>
 #include <i2c.h>
 
 #ifdef CONFIG_HARD_I2C
diff --git a/board/trab/auto_update.c b/board/trab/auto_update.c
index d2c8d44a79..f4074aecb1 100644
--- a/board/trab/auto_update.c
+++ b/board/trab/auto_update.c
@@ -203,7 +203,6 @@ extern int flash_write (char *, ulong, ulong);
 /* change char* to void* to shutup the compiler */
 extern int i2c_write_multiple (uchar, uint, int, void *, int);
 extern int i2c_read_multiple (uchar, uint, int, void *, int);
-extern block_dev_desc_t *get_dev (char*, int);
 extern int u_boot_hush_start(void);
 
 int
diff --git a/board/xilinx/ml300/Makefile b/board/xilinx/ml300/Makefile
index 02c22fbef1..05ad23524f 100644
--- a/board/xilinx/ml300/Makefile
+++ b/board/xilinx/ml300/Makefile
@@ -28,7 +28,7 @@ $(shell mkdir -p $(obj)../xilinx_enet)
 $(shell mkdir -p $(obj)../xilinx_iic)
 endif
 
-INCS		:= -I../ml300 -I../common -I../xilinx_enet -I../xilinx_iic
+INCS		:= -I../common -I../xilinx_enet -I../xilinx_iic
 CFLAGS		+= $(INCS)
 HOST_CFLAGS	+= $(INCS)
 
diff --git a/board/xilinx/ml300/ml300.c b/board/xilinx/ml300/ml300.c
index dad562f1c7..60f0bc24e7 100644
--- a/board/xilinx/ml300/ml300.c
+++ b/board/xilinx/ml300/ml300.c
@@ -38,9 +38,9 @@
  *
  */
 
+#include <config.h>
 #include <common.h>
 #include <asm/processor.h>
-#include "xparameters.h"
 
 #ifdef CFG_ENV_IS_IN_EEPROM
 extern void convert_env(void);
diff --git a/board/xilinx/ml300/serial.c b/board/xilinx/ml300/serial.c
index c204b88e41..9b03f89eff 100644
--- a/board/xilinx/ml300/serial.c
+++ b/board/xilinx/ml300/serial.c
@@ -40,8 +40,7 @@
 #include <asm/processor.h>
 #include <common.h>
 #include <command.h>
-#include <configs/ml300.h>
-#include "xparameters.h"
+#include <config.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
diff --git a/board/xilinx/xilinx_enet/emac_adapter.c b/board/xilinx/xilinx_enet/emac_adapter.c
index b30e897669..f159cb6e39 100644
--- a/board/xilinx/xilinx_enet/emac_adapter.c
+++ b/board/xilinx/xilinx_enet/emac_adapter.c
@@ -37,9 +37,9 @@
 *
 ******************************************************************************/
 
+#include <config.h>
 #include <common.h>
 #include <net.h>
-#include "xparameters.h"
 #include "xemac.h"
 
 #if defined(XPAR_EMAC_0_DEVICE_ID)
diff --git a/board/xilinx/xilinx_enet/xemac.h b/board/xilinx/xilinx_enet/xemac.h
index ed704bf29b..584cb7ac51 100644
--- a/board/xilinx/xilinx_enet/xemac.h
+++ b/board/xilinx/xilinx_enet/xemac.h
@@ -257,9 +257,9 @@
 
 /***************************** Include Files *********************************/
 
+#include <config.h>
 #include "xbasic_types.h"
 #include "xstatus.h"
-#include "xparameters.h"
 #include "xpacket_fifo_v1_00_b.h"	/* Uses v1.00b of Packet Fifo */
 #include "xdma_channel.h"
 
diff --git a/board/xilinx/xilinx_enet/xemac_g.c b/board/xilinx/xilinx_enet/xemac_g.c
index 9340f911f8..d9851574f7 100644
--- a/board/xilinx/xilinx_enet/xemac_g.c
+++ b/board/xilinx/xilinx_enet/xemac_g.c
@@ -43,7 +43,7 @@
 *
 *******************************************************************/
 
-#include "xparameters.h"
+#include <config.h>
 #include "xemac.h"
 
 /*
diff --git a/board/xilinx/xilinx_iic/iic_adapter.c b/board/xilinx/xilinx_iic/iic_adapter.c
index 163fe1511d..37dce03916 100644
--- a/board/xilinx/xilinx_iic/iic_adapter.c
+++ b/board/xilinx/xilinx_iic/iic_adapter.c
@@ -37,10 +37,10 @@
 *
 ******************************************************************************/
 
+#include <config.h>
 #include <common.h>
 #include <environment.h>
 #include <net.h>
-#include "xparameters.h"
 
 #ifdef CFG_ENV_IS_IN_EEPROM
 #include <i2c.h>