omap: remove omap5912osk board support

Emails to the board maintainer
"Rishi Bhattacharya <rishi@ti.com>"
have been bouncing.

Tom suggested to remove this board.

Remove also omap1510_udc.c because this is the last board
to enable it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>

6 files changed, 0 insertions, 852 deletions

diff --git a/board/ti/omap5912osk/Kconfig b/board/ti/omap5912osk/Kconfig
deleted file mode 100644
index 9f7493a35f..0000000000
--- a/board/ti/omap5912osk/Kconfig
+++ /dev/null
@@ -1,23 +0,0 @@
-if TARGET_OMAP5912OSK
-
-config SYS_CPU
-	string
-	default "arm926ejs"
-
-config SYS_BOARD
-	string
-	default "omap5912osk"
-
-config SYS_VENDOR
-	string
-	default "ti"
-
-config SYS_SOC
-	string
-	default "omap"
-
-config SYS_CONFIG_NAME
-	string
-	default "omap5912osk"
-
-endif
diff --git a/board/ti/omap5912osk/MAINTAINERS b/board/ti/omap5912osk/MAINTAINERS
deleted file mode 100644
index 43ffb9b7b9..0000000000
--- a/board/ti/omap5912osk/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-OMAP5912OSK BOARD
-M:	Rishi Bhattacharya <rishi@ti.com>
-S:	Maintained
-F:	board/ti/omap5912osk/
-F:	include/configs/omap5912osk.h
-F:	configs/omap5912osk_defconfig
diff --git a/board/ti/omap5912osk/Makefile b/board/ti/omap5912osk/Makefile
deleted file mode 100644
index d7c0ebd729..0000000000
--- a/board/ti/omap5912osk/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= omap5912osk.o
-obj-y	+= lowlevel_init.o
diff --git a/board/ti/omap5912osk/config.mk b/board/ti/omap5912osk/config.mk
deleted file mode 100644
index 5b8d952ba6..0000000000
--- a/board/ti/omap5912osk/config.mk
+++ /dev/null
@@ -1,30 +0,0 @@
-#
-# (C) Copyright 2002-2004
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# (C) Copyright 2003
-# Texas Instruments, <www.ti.com>
-# Kshitij Gupta <Kshitij@ti.com>
-#
-# (C) Copyright 2004
-# Texas Instruments, <www.ti.com>
-# Rishi Bhattacharya <rishi@ti.com>
-#
-# TI OSK board with OMAP5912 (ARM925EJS) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# OSK has 1 bank of 32 MB SDRAM
-# Physical Address:
-# 1000'0000 to 1200'0000
-#
-#
-# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000
-# (mem base + reserved)
-#
-# When running from RAM use address 1108'0000, otherwise when
-# booting from NOR flash link to address 0000'0000.
-#
-
-CONFIG_SYS_TEXT_BASE = 0x00000000
-#CONFIG_SYS_TEXT_BASE = 0x11080000
diff --git a/board/ti/omap5912osk/lowlevel_init.S b/board/ti/omap5912osk/lowlevel_init.S
deleted file mode 100644
index e05a1c7b55..0000000000
--- a/board/ti/omap5912osk/lowlevel_init.S
+++ /dev/null
@@ -1,477 +0,0 @@
-/*
- * Board specific setup info
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
- *
- * Modified for OMAP 5912 OSK board by Rishi Bhattacharya, Apr 2004
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <config.h>
-#include <version.h>
-
-#if defined(CONFIG_OMAP1610)
-#include <./configs/omap1510.h>
-#endif
-
-.globl lowlevel_init
-lowlevel_init:
-
-	/*------------------------------------------------------*
-	 * Ensure i-cache is enabled                            *
-	 * To configure TC regs without fetching instruction    *
-	 *------------------------------------------------------*/
-	mrc	p15, 0, r0, c1, c0
-	orr	r0, r0, #0x1000
-	mcr	p15, 0, r0, c1, c0
-
-	/*------------------------------------------------------*
-	 *mask all IRQs by setting all bits in the INTMR default*
-	 *------------------------------------------------------*/
-	mov	r1, #0xffffffff
-	ldr	r0, =REG_IHL1_MIR
-	str	r1, [r0]
-	ldr	r0, =REG_IHL2_MIR
-	str	r1, [r0]
-
-	/*------------------------------------------------------*
-	 * Set up ARM CLM registers (IDLECT1)                   *
-	 *------------------------------------------------------*/
-	ldr	r0,	REG_ARM_IDLECT1
-	ldr	r1,	VAL_ARM_IDLECT1
-	str	r1,	[r0]
-
-	/*------------------------------------------------------*
-	 * Set up ARM CLM registers (IDLECT2)                   *
-	 *------------------------------------------------------*/
-	ldr	r0,	REG_ARM_IDLECT2
-	ldr	r1,	VAL_ARM_IDLECT2
-	str	r1,	[r0]
-
-	/*------------------------------------------------------*
-	 * Set up ARM CLM registers (IDLECT3)                   *
-	 *------------------------------------------------------*/
-	ldr	r0,	REG_ARM_IDLECT3
-	ldr	r1,	VAL_ARM_IDLECT3
-	str	r1,	[r0]
-
-	mov	r1,	#0x01               /* PER_EN bit */
-	ldr	r0,	REG_ARM_RSTCT2
-	strh	r1,	[r0]            /* CLKM; Peripheral reset. */
-
-	/* Set CLKM to Sync-Scalable */
-	mov	r1,	#0x1000
-	ldr	r0,	REG_ARM_SYSST
-
-	mov	r2,	#0
-1:	cmp	r2,	#1
-	streqh	r1,	[r0]
-	add	r2,	r2,	#1
-	cmp	r2,	#0x100              /* wait for any bubbles to finish */
-	bne	1b
-
-	ldr	r1,	VAL_ARM_CKCTL
-	ldr	r0,	REG_ARM_CKCTL
-	strh	r1,	[r0]
-
-	/* a few nops to let settle */
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-
-	/* setup DPLL 1 */
-	/* Ramp up the clock to 96Mhz */
-	ldr	r1,	VAL_DPLL1_CTL
-	ldr	r0,	REG_DPLL1_CTL
-	strh	r1,	[r0]
-	ands	r1,	r1,	#0x10       /* Check if PLL is enabled. */
-	beq	lock_end                /* Do not look for lock if BYPASS selected */
-2:
-	ldrh	r1,	[r0]
-	ands	r1,	r1,	#0x01       /* Check the LOCK bit.*/
-	beq 2b                      /* loop until bit goes hi. */
-lock_end:
-
-	/*------------------------------------------------------*
-	 * Turn off the watchdog during init...                 *
-	 *------------------------------------------------------*/
-	ldr	r0,	REG_WATCHDOG
-	ldr	r1,	WATCHDOG_VAL1
-	str	r1,	[r0]
-	ldr	r1,	WATCHDOG_VAL2
-	str	r1,	[r0]
-	ldr	r0,	REG_WSPRDOG
-	ldr	r1,	WSPRDOG_VAL1
-	str	r1,	[r0]
-	ldr	r0,	REG_WWPSDOG
-
-watch1Wait:
-	ldr	r1,	[r0]
-	tst	r1,	#0x10
-	bne	watch1Wait
-
-	ldr	r0,	REG_WSPRDOG
-	ldr	r1,	WSPRDOG_VAL2
-	str	r1,	[r0]
-	ldr	r0,	REG_WWPSDOG
-watch2Wait:
-	ldr	r1,	[r0]
-	tst	r1,	#0x10
-	bne	watch2Wait
-
-	/* Set memory timings corresponding to the new clock speed */
-	ldr	r3, VAL_SDRAM_CONFIG_SDF0
-
-	/* Check execution location to determine current execution location
-	 * and branch to appropriate initialization code.
-	 */
-	mov	r0,	#0x10000000         /* Load physical SDRAM base. */
-	mov	r1,	pc                  /* Get current execution location. */
-	cmp	r1,	r0                  /* Compare. */
-	bge	skip_sdram              /* Skip over EMIF-fast initialization if running from SDRAM. */
-
-	/* identify the device revision, -- TMX or TMP(TMS) */
-	ldr	r0, REG_DEVICE_ID
-	ldr	r1, [r0]
-
-	ldr	r0, VAL_DEVICE_ID_TMP
-	mov	r1, r1, lsl #15
-	mov	r1, r1, lsr #16
-	cmp	r0, r1
-	bne	skip_TMP_Patch
-
-	/* Enable TMP/TMS device new features */
-	mov	r0, #1
-	ldr	r1, REG_TC_EMIFF_DOUBLER
-	str	r0, [r1]
-
-	/* Enable new ac parameters */
-	mov	r0, #0x0b
-	ldr	r1, REG_SDRAM_CONFIG2
-	str	r0, [r1]
-
-	ldr	r3, VAL_SDRAM_CONFIG_SDF1
-
-skip_TMP_Patch:
-
-	/*
-	* Delay for SDRAM initialization.
-	*/
-	mov	r0,	#0x1800		/* value should be checked */
-3:
-	subs	r0,	r0,	#0x1	/* Decrement count */
-	bne	3b
-
-	/*
-	 * Set SDRAM control values. Disable refresh before MRS command.
-	 */
-
-	/* mobile ddr operation */
-	ldr	r0,	REG_SDRAM_OPERATION
-	mov	r2,	#07
-	str	r2,	[r0]
-
-	/* config register */
-	ldr	r0,	REG_SDRAM_CONFIG
-	str	r3,	[r0]
-
-	/* manual command register */
-	ldr	r0,	REG_SDRAM_MANUAL_CMD
-
-	/* issue set cke high */
-	mov	r1,	#CMD_SDRAM_CKE_SET_HIGH
-	str	r1,	[r0]
-
-	/* issue nop */
-	mov	r1,	#CMD_SDRAM_NOP
-	str	r1,	[r0]
-
-	mov	r2,	#0x0100
-waitMDDR1:
-	subs	r2,	r2,	 #1
-	bne	waitMDDR1	/* delay loop */
-
-	/* issue precharge */
-	mov	r1,	#CMD_SDRAM_PRECHARGE
-	str	r1,	[r0]
-
-	/* issue autorefresh x 2 */
-	mov	r1,	#CMD_SDRAM_AUTOREFRESH
-	str	r1,	[r0]
-	str	r1,	[r0]
-
-	/* mrs register ddr mobile */
-	ldr	r0,	REG_SDRAM_MRS
-	mov	r1,	#0x33
-	str	r1,	[r0]
-
-	/* emrs1 low-power register */
-	ldr	r0,	REG_SDRAM_EMRS1
-	/* self refresh on all banks */
-	mov	r1,	#0
-	str	r1,	[r0]
-
-	ldr	r0,	REG_DLL_URD_CONTROL
-	ldr	r1,	DLL_URD_CONTROL_VAL
-	str	r1,	[r0]
-
-	ldr	r0,	REG_DLL_LRD_CONTROL
-	ldr	r1,	DLL_LRD_CONTROL_VAL
-	str	r1,	[r0]
-
-	ldr	r0,	REG_DLL_WRT_CONTROL
-	ldr	r1,	DLL_WRT_CONTROL_VAL
-	str	r1,	[r0]
-
-	/* delay loop */
-	mov	r0,	#0x0100
-waitMDDR2:
-	subs	r0,	r0,	#1
-	bne	waitMDDR2
-
-	/*
-	 * Delay for SDRAM initialization.
-	 */
-	mov	r0,	#0x1800
-4:
-	subs	r0,	r0,	#1	/* Decrement count. */
-	bne	4b
-	b	common_tc
-
-skip_sdram:
-	ldr	r0,	REG_SDRAM_CONFIG
-	str	r3,	[r0]
-
-common_tc:
-	/* slow interface */
-	ldr	r1,	VAL_TC_EMIFS_CS0_CONFIG
-	ldr	r0,	REG_TC_EMIFS_CS0_CONFIG
-	str	r1,	[r0] /* Chip Select 0 */
-
-	ldr	r1,	VAL_TC_EMIFS_CS1_CONFIG
-	ldr	r0,	REG_TC_EMIFS_CS1_CONFIG
-	str	r1,	[r0] /* Chip Select 1 */
-
-	ldr	r1,	VAL_TC_EMIFS_CS3_CONFIG
-	ldr	r0,	REG_TC_EMIFS_CS3_CONFIG
-	str	r1,	[r0] /* Chip Select 3 */
-
-	ldr	r1,	VAL_TC_EMIFS_DWS
-	ldr	r0,	REG_TC_EMIFS_DWS
-	str	r1,	[r0] /* Enable EMIFS.RDY for CS1 (ether) */
-
-#ifdef CONFIG_H2_OMAP1610
-	/* inserting additional 2 clock cycle hold time for LAN */
-	ldr     r0,     REG_TC_EMIFS_CS1_ADVANCED
-	ldr	r1,     VAL_TC_EMIFS_CS1_ADVANCED
-	str     r1,     [r0]
-#endif
-	/* Start MPU Timer 1 */
-	ldr	r0,	REG_MPU_LOAD_TIMER
-	ldr	r1,	VAL_MPU_LOAD_TIMER
-	str	r1,	[r0]
-
-	ldr	r0,	REG_MPU_CNTL_TIMER
-	ldr	r1,	VAL_MPU_CNTL_TIMER
-	str	r1,	[r0]
-
-	/*
-	 * Setup a temporary stack
-	 */
-	ldr	sp,	SRAM_STACK
-	bic	sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
-	/*
-	 * Save the old lr(passed in ip) and the current lr to stack
-	 */
-	push	{ip, lr}
-
-	/*
-	 * go setup pll, mux, memory
-	 */
-	bl	s_init
-	pop	{ip, pc}
-
-	/* back to arch calling code */
-	mov	pc,	lr
-
-	/* the literal pools origin */
-	.ltorg
-
-REG_DEVICE_ID:			/* 32 bits */
-	.word 0xfffe2004
-REG_TC_EMIFS_CONFIG:
-	.word 0xfffecc0c
-REG_TC_EMIFS_CS0_CONFIG:	/* 32 bits */
-	.word 0xfffecc10
-REG_TC_EMIFS_CS1_CONFIG:	/* 32 bits */
-	.word 0xfffecc14
-REG_TC_EMIFS_CS2_CONFIG:	/* 32 bits */
-	.word 0xfffecc18
-REG_TC_EMIFS_CS3_CONFIG:	/* 32 bits */
-	.word 0xfffecc1c
-REG_TC_EMIFS_DWS:		/* 32 bits */
-	.word 0xfffecc40
-#ifdef CONFIG_H2_OMAP1610
-REG_TC_EMIFS_CS1_ADVANCED:	/* 32 bits */
-	.word 0xfffecc54
-#endif
-
-/* MPU clock/reset/power mode control registers */
-REG_ARM_CKCTL:			/* 16 bits */
-	.word 0xfffece00
-REG_ARM_IDLECT3:		/* 16 bits */
-	.word 0xfffece24
-REG_ARM_IDLECT2:		/* 16 bits */
-	.word 0xfffece08
-REG_ARM_IDLECT1:		/* 16 bits */
-	.word 0xfffece04
-REG_ARM_RSTCT2:			/* 16 bits */
-	.word 0xfffece14
-REG_ARM_SYSST:			/* 16 bits */
-	.word 0xfffece18
-
-/* DPLL control registers */
-REG_DPLL1_CTL:			/* 16 bits */
-	.word 0xfffecf00
-
-/* Watch Dog register */
-/* secure watchdog stop */
-REG_WSPRDOG:
-	.word 0xfffeb048
-/* watchdog write pending */
-REG_WWPSDOG:
-	.word 0xfffeb034
-
-WSPRDOG_VAL1:
-	.word 0x0000aaaa
-WSPRDOG_VAL2:
-	.word 0x00005555
-
-/* SDRAM config is: auto refresh enabled, 16 bit 4 bank,
- counter @8192 rows, 10 ns, 8 burst */
-REG_SDRAM_CONFIG:
-	.word 0xfffecc20
-REG_SDRAM_CONFIG2:
-	.word 0xfffecc3c
-REG_TC_EMIFF_DOUBLER:		/* 32 bits */
-	.word 0xfffecc60
-
-/* Operation register */
-REG_SDRAM_OPERATION:
-	.word 0xfffecc80
-
-/* Manual command register */
-REG_SDRAM_MANUAL_CMD:
-	.word 0xfffecc84
-
-/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
-REG_SDRAM_MRS:
-	.word 0xfffecc70
-
-/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
-REG_SDRAM_EMRS1:
-	.word 0xfffecc78
-
-/* WRT DLL register */
-REG_DLL_WRT_CONTROL:
-	.word 0xfffecc68
-DLL_WRT_CONTROL_VAL:
-	.word 0x03f00002    /* Phase of 72deg, write offset +31  */
-
-/* URD DLL register */
-REG_DLL_URD_CONTROL:
-	.word 0xfffeccc0
-DLL_URD_CONTROL_VAL:
-	.word 0x00800002    /* Phase of 72deg, read offset +31  */
-
-/* LRD DLL register */
-REG_DLL_LRD_CONTROL:
-	.word 0xfffecccc
-DLL_LRD_CONTROL_VAL:
-	.word 0x00800002    /* read offset +31  */
-
-REG_WATCHDOG:
-	.word 0xfffec808
-WATCHDOG_VAL1:
-	.word 0x000000f5
-WATCHDOG_VAL2:
-	.word 0x000000a0
-
-REG_MPU_LOAD_TIMER:
-	.word 0xfffec504
-REG_MPU_CNTL_TIMER:
-	.word 0xfffec500
-VAL_MPU_LOAD_TIMER:
-	.word 0xffffffff
-VAL_MPU_CNTL_TIMER:
-	.word 0xffffffa1
-
-/* 96 MHz Samsung Mobile DDR */
-/* Original setting for TMX device */
-VAL_SDRAM_CONFIG_SDF0:
-    .word 0x0014e6fe
-
-/* NEW_SYS_FREQ mode (valid only TMP/TMS devices) */
-VAL_SDRAM_CONFIG_SDF1:
-    .word 0x0114e6fe
-
-VAL_ARM_CKCTL:
-	.word 0x2000		/* was:	0x3000, now use CLK_REF for timer input */
-VAL_DPLL1_CTL:
-	.word 0x2830
-
-#ifdef CONFIG_OSK_OMAP5912
-VAL_TC_EMIFS_CS0_CONFIG:
-	.word 0x002130b0
-VAL_TC_EMIFS_CS1_CONFIG:
-	.word 0x00001133
-VAL_TC_EMIFS_CS2_CONFIG:
-	.word 0x000055f0
-VAL_TC_EMIFS_CS3_CONFIG:
-	.word 0x88013141
-VAL_TC_EMIFS_DWS:	/* Enable EMIFS.RDY for CS1 access (ether) */
-	.word 0x000000c0
-VAL_DEVICE_ID_TMP:	/* TMP/TMS=0xb65f, TMX=0xb58c */
-	.word 0xb65f
-#endif
-
-#ifdef CONFIG_H2_OMAP1610
-VAL_TC_EMIFS_CS0_CONFIG:
-	.word 0x00203331
-VAL_TC_EMIFS_CS1_CONFIG:
-	.word 0x8180fff3
-VAL_TC_EMIFS_CS2_CONFIG:
-	.word 0xf800f22a
-VAL_TC_EMIFS_CS3_CONFIG:
-	.word 0x88013141
-VAL_TC_EMIFS_CS1_ADVANCED:
-	.word 0x00000022
-#endif
-
-VAL_ARM_IDLECT1:
-	.word 0x00000400
-VAL_ARM_IDLECT2:
-	.word 0x00000886
-VAL_ARM_IDLECT3:
-	.word 0x00000015
-
-SRAM_STACK:
-	.word CONFIG_SYS_INIT_SP_ADDR
-
-/* command values */
-.equ CMD_SDRAM_NOP,             0x00000000
-.equ CMD_SDRAM_PRECHARGE,       0x00000001
-.equ CMD_SDRAM_AUTOREFRESH,     0x00000002
-.equ CMD_SDRAM_CKE_SET_HIGH,    0x00000007
diff --git a/board/ti/omap5912osk/omap5912osk.c b/board/ti/omap5912osk/omap5912osk.c
deleted file mode 100644
index 88a7310cec..0000000000
--- a/board/ti/omap5912osk/omap5912osk.c
+++ /dev/null
@@ -1,307 +0,0 @@
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002
- * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Rishi Bhattacharya <rishi@ti.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#if defined(CONFIG_OMAP1610)
-#include <./configs/omap1510.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void flash__init (void);
-void ether__init (void);
-void set_muxconf_regs (void);
-void peripheral_power_enable (void);
-
-#define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF)
-
-static inline void delay (unsigned long loops)
-{
-	__asm__ volatile ("1:\n"
-		"subs %0, %1, #1\n"
-		"bne 1b":"=r" (loops):"0" (loops));
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
-	gd->bd->bi_arch_number = MACH_TYPE_OMAP_OSK;
-
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x10000100;
-
-	flash__init();
-	ether__init();
-
-	return 0;
-}
-
-void s_init(void)
-{
-	/* Configure MUX settings */
-	set_muxconf_regs ();
-	peripheral_power_enable ();
-
-/* this speeds up your boot a quite a bit.  However to make it
- *  work, you need make sure your kernel startup flush bug is fixed.
- *  ... rkw ...
- */
-	icache_enable ();
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-void flash__init (void)
-{
-#define EMIFS_GlB_Config_REG 0xfffecc0c
-	unsigned int regval;
-	regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
-	/* Turn off write protection for flash devices. */
-	regval = regval | 0x0001;
-	*((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
-}
-/*************************************************************
- Routine:ether__init
- Description: take the Ethernet controller out of reset and wait
-			   for the EEPROM load to complete.
-*************************************************************/
-void ether__init (void)
-{
-#define ETH_CONTROL_REG 0x0480000b
-	int i;
-
-	*((volatile unsigned short *) 0xfffece08) = 0x03FF;
-	*((volatile unsigned short *) 0xfffb3824) = 0x8000;
-	*((volatile unsigned short *) 0xfffb3830) = 0x0000;
-	*((volatile unsigned short *) 0xfffb3834) = 0x0009;
-	*((volatile unsigned short *) 0xfffb3838) = 0x0009;
-	*((volatile unsigned short *) 0xfffb3818) = 0x0002;
-	*((volatile unsigned short *) 0xfffb382C) = 0x0048;
-	*((volatile unsigned short *) 0xfffb3824) = 0x8603;
-	udelay (3);
-	for (i=0;i<2000;i++);
-	*((volatile unsigned short *) 0xfffb381C) = 0x6610;
-	udelay (30);
-	for (i=0;i<10000;i++);
-
-	*((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
-	udelay (3);
-
-
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-int dram_init(void)
-{
-	gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
-
-	return 0;
-}
-
-void dram_init_banksize(void)
-{
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-}
-
-/******************************************************
- Routine: set_muxconf_regs
- Description: Setting up the configuration Mux registers
-			  specific to the hardware
-*******************************************************/
-void set_muxconf_regs (void)
-{
-	volatile unsigned int *MuxConfReg;
-	/* set each registers to its reset value; */
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
-	/* setup for UART1 */
-	*MuxConfReg &= ~(0x02000000);	/* bit 25 */
-	/* setup for UART2 */
-	*MuxConfReg &= ~(0x01000000);	/* bit 24 */
-	/* Disable Uwire CS Hi-Z */
-	*MuxConfReg |= 0x08000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_3);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_4);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_5);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_6);
-	/*setup mux for UART3 */
-	*MuxConfReg |= 0x00000001;	/* bit3, 1, 0 (mux0 5,5,26) */
-	*MuxConfReg &= ~0x0000003e;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_7);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_8);
-	/* Disable Uwire CS Hi-Z */
-	*MuxConfReg |= 0x00001200;	/*bit 9 for CS0 12 for CS3 */
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_9);
-	/*  Need to turn on bits 21 and 12 in FUNC_MUX_CTRL_9 so the  */
-	/*  hardware will actually use TX and RTS based on bit 25 in  */
-	/*  FUNC_MUX_CTRL_0.  I told you this thing was screwy!	 */
-	*MuxConfReg |= 0x00201000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_A);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_B);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_C);
-	/* setup for UART2 */
-	/*  Need to turn on bits 27 and 24 in FUNC_MUX_CTRL_C so the  */
-	/*  hardware will actually use TX and RTS based on bit 24 in  */
-	/*  FUNC_MUX_CTRL_0. */
-	*MuxConfReg |= 0x09000000;
-	MuxConfReg =
-	(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_D);
-	*MuxConfReg |= 0x00000020;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_0);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_1);
-	*MuxConfReg = 0x00000000;
-	/* mux setup for SD/MMC driver */
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_2);
-	*MuxConfReg &= 0xFFFE0FFF;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_3);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
-	/* bit 13 for MMC2 XOR_CLK */
-	*MuxConfReg &= ~(0x00002000);
-	/* bit 29 for UART 1 */
-	*MuxConfReg &= ~(0x00002000);
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
-	/* Configure for USB. Turn on VBUS_CTRL and VBUS_MODE. */
-	*MuxConfReg |= 0x000C0000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int)USB_TRANSCEIVER_CTRL);
-	*MuxConfReg &= ~(0x00000070);
-	*MuxConfReg &= ~(0x00000008);
-	*MuxConfReg |= 0x00000003;
-	*MuxConfReg |= 0x00000180;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
-	/* bit 17, software controls VBUS */
-	*MuxConfReg &= ~(0x00020000);
-	/* Enable USB 48 and 12M clocks */
-	*MuxConfReg |= 0x00000200;
-	*MuxConfReg &= ~(0x00000180);
-	/*2.75V for MMCSDIO1 */
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) VOLTAGE_CTRL_0);
-	*MuxConfReg = 0x00001FE7;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PU_PD_SEL_0);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PU_PD_SEL_1);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PU_PD_SEL_3);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PU_PD_SEL_4);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_4);
-	*MuxConfReg = 0x00000000;
-	/* Turn on UART2 48 MHZ clock */
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
-	*MuxConfReg |= 0x40000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) USB_OTG_CTRL);
-	/* setup for USB VBus detection OMAP161x */
-	*MuxConfReg |= 0x00040000;	/* bit 18 */
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
-	/* PullUps for SD/MMC driver */
-	*MuxConfReg |= ~(0xFFFE0FFF);
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int)COMP_MODE_CTRL_0);
-	*MuxConfReg = COMP_MODE_ENABLE;
-}
-
-/******************************************************
- Routine: peripheral_power_enable
- Description: Enable the power for UART1
-*******************************************************/
-void peripheral_power_enable (void)
-{
-#define UART1_48MHZ_ENABLE	((unsigned short)0x0200)
-#define SW_CLOCK_REQUEST	((volatile unsigned short *)0xFFFE0834)
-
-	*SW_CLOCK_REQUEST |= UART1_48MHZ_ENABLE;
-}
-
-/*
- * Check Board Identity
- */
-int checkboard(void)
-{
-	char buf[64];
-	int i = getenv_f("serial#", buf, sizeof(buf));
-
-	puts("Board: OSK5912");
-
-	if (i > 0) {
-		puts(", serial# ");
-		puts(buf);
-	}
-	putc('\n');
-
-	return (0);
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0;
-#ifdef CONFIG_LAN91C96
-	rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE);
-#endif
-	return rc;
-}
-#endif