rename CFG_ macros to CONFIG_SYS

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

2 files changed, 20 insertions, 20 deletions

diff --git a/board/mcc200/auto_update.c b/board/mcc200/auto_update.c
index 2ed66ddb41..49213d0b38 100644
--- a/board/mcc200/auto_update.c
+++ b/board/mcc200/auto_update.c
@@ -25,7 +25,7 @@
 #include <usb.h>
 #include <part.h>
 
-#ifdef CFG_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
 #include <hush.h>
 #endif
 
@@ -40,8 +40,8 @@
 #error "must define CONFIG_USB_STORAGE"
 #endif
 
-#ifndef CFG_HUSH_PARSER
-#error "must define CFG_HUSH_PARSER"
+#ifndef CONFIG_SYS_HUSH_PARSER
+#error "must define CONFIG_SYS_HUSH_PARSER"
 #endif
 
 #if !defined(CONFIG_CMD_FAT)
diff --git a/board/mcc200/mcc200.c b/board/mcc200/mcc200.c
index 65b818471a..14cf08da3f 100644
--- a/board/mcc200/mcc200.c
+++ b/board/mcc200/mcc200.c
@@ -47,7 +47,7 @@ extern flash_info_t flash_info[];	/* FLASH chips info */
 extern int do_auto_update(void);
 ulong flash_get_size (ulong base, int banknum);
 
-#ifndef CFG_RAMBOOT
+#ifndef CONFIG_SYS_RAMBOOT
 static void sdram_start (int hi_addr)
 {
 	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
@@ -92,7 +92,7 @@ static void sdram_start (int hi_addr)
 
 /*
  * ATTENTION: Although partially referenced initdram does NOT make real use
- *	      use of CFG_SDRAM_BASE. The code does not work if CFG_SDRAM_BASE
+ *	      use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE
  *	      is something else than 0x00000000.
  */
 
@@ -101,7 +101,7 @@ phys_size_t initdram (int board_type)
 	ulong dramsize = 0;
 	ulong dramsize2 = 0;
 	uint svr, pvr;
-#ifndef CFG_RAMBOOT
+#ifndef CONFIG_SYS_RAMBOOT
 	ulong test1, test2;
 
 	/* setup SDRAM chip selects */
@@ -122,9 +122,9 @@ phys_size_t initdram (int board_type)
 
 	/* find RAM size using SDRAM CS0 only */
 	sdram_start(0);
-	test1 = get_ram_size((long *)CFG_SDRAM_BASE, 0x80000000);
+	test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
 	sdram_start(1);
-	test2 = get_ram_size((long *)CFG_SDRAM_BASE, 0x80000000);
+	test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
 	if (test1 > test2) {
 		sdram_start(0);
 		dramsize = test1;
@@ -150,10 +150,10 @@ phys_size_t initdram (int board_type)
 	/* find RAM size using SDRAM CS1 only */
 	if (!dramsize)
 		sdram_start(0);
-	test2 = test1 = get_ram_size((long *)(CFG_SDRAM_BASE + dramsize), 0x80000000);
+	test2 = test1 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
 	if (!dramsize) {
 		sdram_start(1);
-		test2 = get_ram_size((long *)(CFG_SDRAM_BASE + dramsize), 0x80000000);
+		test2 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
 	}
 	if (test1 > test2) {
 		sdram_start(0);
@@ -175,7 +175,7 @@ phys_size_t initdram (int board_type)
 		*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
 	}
 
-#else /* CFG_RAMBOOT */
+#else /* CONFIG_SYS_RAMBOOT */
 
 	/* retrieve size of memory connected to SDRAM CS0 */
 	dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
@@ -193,7 +193,7 @@ phys_size_t initdram (int board_type)
 		dramsize2 = 0;
 	}
 
-#endif /* CFG_RAMBOOT */
+#endif /* CONFIG_SYS_RAMBOOT */
 
 	/*
 	 * On MPC5200B we need to set the special configuration delay in the
@@ -237,7 +237,7 @@ int misc_init_r (void)
 	/*
 	 * Check if boot FLASH isn't max size
 	 */
-	if (gd->bd->bi_flashsize < (0 - CFG_FLASH_BASE)) {
+	if (gd->bd->bi_flashsize < (0 - CONFIG_SYS_FLASH_BASE)) {
 		/* adjust mapping */
 		*(vu_long *)MPC5XXX_BOOTCS_START = *(vu_long *)MPC5XXX_CS0_START =
 			START_REG(gd->bd->bi_flashstart);
@@ -247,31 +247,31 @@ int misc_init_r (void)
 		/*
 		 * Re-check to get correct base address
 		 */
-		flash_get_size(gd->bd->bi_flashstart, CFG_MAX_FLASH_BANKS - 1);
+		flash_get_size(gd->bd->bi_flashstart, CONFIG_SYS_MAX_FLASH_BANKS - 1);
 
 		/*
 		 * Re-do flash protection upon new addresses
 		 */
 		flash_protect (FLAG_PROTECT_CLEAR,
 			       gd->bd->bi_flashstart, 0xffffffff,
-			       &flash_info[CFG_MAX_FLASH_BANKS - 1]);
+			       &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
 
 		/* Monitor protection ON by default */
 		flash_protect (FLAG_PROTECT_SET,
-			       CFG_MONITOR_BASE, CFG_MONITOR_BASE + monitor_flash_len - 1,
-			       &flash_info[CFG_MAX_FLASH_BANKS - 1]);
+			       CONFIG_SYS_MONITOR_BASE, CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
+			       &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
 
 		/* Environment protection ON by default */
 		flash_protect (FLAG_PROTECT_SET,
 			       CONFIG_ENV_ADDR,
 			       CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
-			       &flash_info[CFG_MAX_FLASH_BANKS - 1]);
+			       &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
 
 		/* Redundant environment protection ON by default */
 		flash_protect (FLAG_PROTECT_SET,
 			       CONFIG_ENV_ADDR_REDUND,
 			       CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SIZE_REDUND - 1,
-			       &flash_info[CFG_MAX_FLASH_BANKS - 1]);
+			       &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
 	}
 
 	if (gd->bd->bi_flashsize > (32 << 20)) {
@@ -325,6 +325,6 @@ void ide_set_reset (int idereset)
 #if defined(CONFIG_CMD_DOC)
 void doc_init (void)
 {
-	doc_probe (CFG_DOC_BASE);
+	doc_probe (CONFIG_SYS_DOC_BASE);
 }
 #endif