ppc4xx: Update AMCC Bamboo 440EP support

Changed storage type of cfg_simulate_spd_eeprom to const
Changed storage type of gpio_tab to stack storage
(Cannot access global data declarations in .bss until afer code relocation)

Improved SDRAM tests to catch problems where data is not uniquely addressable
(e.g. incorrectly programmed SDRAM row or columns)

Added CONFIG_PROG_SDRAM_TLB to support Bamboo SIMM/DIMM modules
Fixed AM29LV320DT (OpCode Flash) sector map

Signed-off-by: Eugene OBrien <eugene.obrien@advantechamt.com>
Signed-off-by: Stefan Roese <sr@denx.de>

1 files changed, 226 insertions, 95 deletions

diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
index caf66909b9..00c793afd0 100644
--- a/board/amcc/bamboo/bamboo.c
+++ b/board/amcc/bamboo/bamboo.c
@@ -32,9 +32,170 @@ void ext_bus_cntlr_init(void);
 void configure_ppc440ep_pins(void);
 int is_nand_selected(void);
 
-unsigned char cfg_simulate_spd_eeprom[128];
+#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL))
+/*************************************************************************
+ *
+ * Bamboo has one bank onboard sdram (plus DIMM)
+ *
+ * Fixed memory is composed of :
+ *	MT46V16M16TG-75 from Micron (x 2), 256Mb, 16 M x16, DDR266,
+ *	13 row add bits, 10 column add bits (but 12 row used only).
+ *	ECC device: MT46V16M8TG-75 from Micron (x 1), 128Mb, x8, DDR266,
+ *	12 row add bits, 10 column add bits.
+ *	Prepare a subset (only the used ones) of SPD data
+ *
+ *	Note : if the ECC is enabled (SDRAM_ECC_ENABLE) the size of
+ *	the corresponding bank is divided by 2 due to number of Row addresses
+ *	12 in the ECC module
+ *
+ *  Assumes:	64 MB, ECC, non-registered
+ *		PLB @ 133 MHz
+ *
+ ************************************************************************/
+const unsigned char cfg_simulate_spd_eeprom[128] = {
+	0x80,    /* number of SPD bytes used: 128 */
+	0x08,    /*  total number bytes in SPD device = 256 */
+	0x07,    /* DDR ram */
+#ifdef CONFIG_DDR_ECC
+	0x0C,    /* num Row Addr: 12 */
+#else
+	0x0D,    /* num Row Addr: 13 */
+#endif
+	0x09,    /* numColAddr: 9  */
+	0x01,    /* numBanks: 1 */
+	0x20,    /* Module data width: 32 bits */
+	0x00,    /* Module data width continued: +0 */
+	0x04,    /* 2.5 Volt */
+	0x75,    /* SDRAM Cycle Time (cas latency 2.5) = 7.5 ns */
+#ifdef CONFIG_DDR_ECC
+	0x02,    /* ECC ON : 02 OFF : 00 */
+#else
+	0x00,    /* ECC ON : 02 OFF : 00 */
+#endif
+	0x82,    /* refresh Rate Type: Normal (15.625us) + Self refresh */
+	0,
+	0,
+	0,
+	0x01,    /* wcsbc = 1 */
+	0,
+	0,
+	0x0C,    /* casBit (2,2.5) */
+	0,
+	0,
+	0x00,    /* not registered: 0  registered : 0x02*/
+	0,
+	0xA0,    /* SDRAM Cycle Time (cas latency 2) = 10 ns */
+	0,
+	0x00,    /* SDRAM Cycle Time (cas latency 1.5) = N.A */
+	0,
+	0x50,    /* tRpNs = 20 ns  */
+	0,
+	0x50,    /* tRcdNs = 20 ns */
+	45,      /* tRasNs */
+#ifdef CONFIG_DDR_ECC
+	0x08,    /* bankSizeID: 32MB */
+#else
+	0x10,    /* bankSizeID: 64MB */
+#endif
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0,
+	0
+};
+#endif
 
-gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX];
 #if 0
 {	   /* GPIO   Alternate1	      Alternate2	Alternate3 */
     {
@@ -291,73 +452,12 @@ int checkboard(void)
 	return (0);
 }
 
-#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL))
-/*************************************************************************
- *
- * init_spd_array -- Bamboo has one bank onboard sdram (plus DIMM)
- *
- * Fixed memory is composed of :
- *	MT46V16M16TG-75 from Micron (x 2), 256Mb, 16 M x16, DDR266,
- *	13 row add bits, 10 column add bits (but 12 row used only).
- *	ECC device: MT46V16M8TG-75 from Micron (x 1), 128Mb, x8, DDR266,
- *	12 row add bits, 10 column add bits.
- *	Prepare a subset (only the used ones) of SPD data
- *
- *	Note : if the ECC is enabled (SDRAM_ECC_ENABLE) the size of
- *	the corresponding bank is divided by 2 due to number of Row addresses
- *	12 in the ECC module
- *
- *  Assumes:	64 MB, ECC, non-registered
- *		PLB @ 133 MHz
- *
- ************************************************************************/
-static void init_spd_array(void)
-{
-	cfg_simulate_spd_eeprom[8]     = 0x04;    /* 2.5 Volt */
-	cfg_simulate_spd_eeprom[2]     = 0x07;    /* DDR ram */
-
-#ifdef CONFIG_DDR_ECC
-	cfg_simulate_spd_eeprom[11]    = 0x02;    /* ECC ON : 02 OFF : 00 */
-	cfg_simulate_spd_eeprom[31]    = 0x08;    /* bankSizeID: 32MB */
-	cfg_simulate_spd_eeprom[3]     = 0x0C;    /* num Row Addr: 12 */
-#else
-	cfg_simulate_spd_eeprom[11]    = 0x00;    /* ECC ON : 02 OFF : 00 */
-	cfg_simulate_spd_eeprom[31]    = 0x10;    /* bankSizeID: 64MB */
-	cfg_simulate_spd_eeprom[3]     = 0x0D;    /* num Row Addr: 13 */
-#endif
-
-	cfg_simulate_spd_eeprom[4]     = 0x09;    /* numColAddr: 9  */
-	cfg_simulate_spd_eeprom[5]     = 0x01;    /* numBanks: 1 */
-	cfg_simulate_spd_eeprom[0]     = 0x80;    /* number of SPD bytes used: 128 */
-	cfg_simulate_spd_eeprom[1]     = 0x08;    /*  total number bytes in SPD device = 256 */
-	cfg_simulate_spd_eeprom[21]    = 0x00;    /* not registered: 0  registered : 0x02*/
-	cfg_simulate_spd_eeprom[6]     = 0x20;    /* Module data width: 32 bits */
-	cfg_simulate_spd_eeprom[7]     = 0x00;    /* Module data width continued: +0 */
-	cfg_simulate_spd_eeprom[15]    = 0x01;    /* wcsbc = 1 */
-	cfg_simulate_spd_eeprom[27]    = 0x50;    /* tRpNs = 20 ns  */
-	cfg_simulate_spd_eeprom[29]    = 0x50;    /* tRcdNs = 20 ns */
-
-	cfg_simulate_spd_eeprom[30]    = 45;      /* tRasNs */
-
-	cfg_simulate_spd_eeprom[18]    = 0x0C;    /* casBit (2,2.5) */
-
-	cfg_simulate_spd_eeprom[9]     = 0x75;    /* SDRAM Cycle Time (cas latency 2.5) = 7.5 ns */
-	cfg_simulate_spd_eeprom[23]    = 0xA0;    /* SDRAM Cycle Time (cas latency 2) = 10 ns */
-	cfg_simulate_spd_eeprom[25]    = 0x00;    /* SDRAM Cycle Time (cas latency 1.5) = N.A */
-	cfg_simulate_spd_eeprom[12]    = 0x82;    /* refresh Rate Type: Normal (15.625us) + Self refresh */
-}
-#endif
 
 long int initdram (int board_type)
 {
 #if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL))
 	long dram_size;
 
-	/*
-	 * First write simulated values in eeprom array for onboard bank 0
-	 */
-	init_spd_array();
-
 	dram_size = spd_sdram();
 
 	return dram_size;
@@ -371,11 +471,12 @@ int testdram(void)
 {
 	unsigned long *mem = (unsigned long *)0;
 	const unsigned long kend = (1024 / sizeof(unsigned long));
-	unsigned long k, n;
+	unsigned long k, n, *p32, ctr;
+	const unsigned long bend = CFG_MBYTES_SDRAM * 1024 * 1024;
 
 	mtmsr(0);
 
-	for (k = 0; k < CFG_KBYTES_SDRAM;
+	for (k = 0; k <	CFG_MBYTES_SDRAM*1024;
 	     ++k, mem += (1024 / sizeof(unsigned long))) {
 		if ((k & 1023) == 0) {
 			printf("%3d MB\r", k / 1024);
@@ -399,6 +500,34 @@ int testdram(void)
 			}
 		}
 	}
+
+	/*
+	 * Perform a sequence test to ensure that all
+	 * memory locations are uniquely addressable
+	 */
+	ctr = 0;
+	p32 = 0;
+	while ((unsigned long)p32 != bend) {
+		if (0 == ((unsigned long)p32 & ((1<<20)-1)))
+			printf("Writing	%3d MB\r", (unsigned long)p32 >> 20);
+		*p32++ = ctr++;
+	}
+
+	ctr = 0;
+	p32 = 0;
+	while ((unsigned long)p32 != bend) {
+		if (0 == ((unsigned long)p32 & ((1<<20)-1)))
+			printf("Verifying %3d MB\r", (unsigned long)p32 >> 20);
+
+		if (*p32 != ctr) {
+			printf("SDRAM test fails at: %08x\n", p32);
+			return 1;
+		}
+
+		ctr++;
+		p32++;
+	}
+
 	printf("SDRAM test passes\n");
 	return 0;
 }
@@ -1211,7 +1340,7 @@ void uart_selection_in_fpga(uart_config_nb_t uart_config)
 /*----------------------------------------------------------------------------+
   | init_default_gpio
   +----------------------------------------------------------------------------*/
-void init_default_gpio(void)
+void init_default_gpio(gpio_param_s (*gpio_tab)[GPIO_MAX])
 {
 	int i;
 
@@ -1281,7 +1410,7 @@ void init_default_gpio(void)
   |
   +----------------------------------------------------------------------------*/
 
-void update_uart_ios(uart_config_nb_t uart_config)
+void update_uart_ios(uart_config_nb_t uart_config, gpio_param_s (*gpio_tab)[GPIO_MAX])
 {
 	switch (uart_config)
 	{
@@ -1409,7 +1538,7 @@ void update_uart_ios(uart_config_nb_t uart_config)
 /*----------------------------------------------------------------------------+
   | update_ndfc_ios(void).
   +----------------------------------------------------------------------------*/
-void update_ndfc_ios(void)
+void update_ndfc_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
 {
 	/* Update GPIO Configuration Table */
 	gpio_tab[GPIO0][6].in_out = GPIO_OUT;	    /* EBC_CS_N(1) */
@@ -1427,7 +1556,7 @@ void update_ndfc_ios(void)
 /*----------------------------------------------------------------------------+
   | update_zii_ios(void).
   +----------------------------------------------------------------------------*/
-void update_zii_ios(void)
+void update_zii_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
 {
 	/* Update GPIO Configuration Table */
 	gpio_tab[GPIO0][12].in_out = GPIO_IN;	    /* ZII_p0Rxd(0) */
@@ -1477,7 +1606,7 @@ void update_zii_ios(void)
 /*----------------------------------------------------------------------------+
   | update_uic_0_3_irq_ios().
   +----------------------------------------------------------------------------*/
-void update_uic_0_3_irq_ios(void)
+void update_uic_0_3_irq_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
 {
 	gpio_tab[GPIO1][8].in_out = GPIO_IN;	    /* UIC_IRQ(0) */
 	gpio_tab[GPIO1][8].alt_nb = GPIO_ALT1;
@@ -1495,7 +1624,7 @@ void update_uic_0_3_irq_ios(void)
 /*----------------------------------------------------------------------------+
   | update_uic_4_9_irq_ios().
   +----------------------------------------------------------------------------*/
-void update_uic_4_9_irq_ios(void)
+void update_uic_4_9_irq_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
 {
 	gpio_tab[GPIO1][12].in_out = GPIO_IN;	    /* UIC_IRQ(4) */
 	gpio_tab[GPIO1][12].alt_nb = GPIO_ALT1;
@@ -1516,7 +1645,7 @@ void update_uic_4_9_irq_ios(void)
 /*----------------------------------------------------------------------------+
   | update_dma_a_b_ios().
   +----------------------------------------------------------------------------*/
-void update_dma_a_b_ios(void)
+void update_dma_a_b_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
 {
 	gpio_tab[GPIO1][12].in_out = GPIO_OUT;	    /* DMA_ACK(1) */
 	gpio_tab[GPIO1][12].alt_nb = GPIO_ALT2;
@@ -1537,7 +1666,7 @@ void update_dma_a_b_ios(void)
 /*----------------------------------------------------------------------------+
   | update_dma_c_d_ios().
   +----------------------------------------------------------------------------*/
-void update_dma_c_d_ios(void)
+void update_dma_c_d_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
 {
 	gpio_tab[GPIO0][0].in_out = GPIO_IN;	    /* DMA_REQ(2) */
 	gpio_tab[GPIO0][0].alt_nb = GPIO_ALT2;
@@ -1562,7 +1691,7 @@ void update_dma_c_d_ios(void)
 /*----------------------------------------------------------------------------+
   | update_ebc_master_ios().
   +----------------------------------------------------------------------------*/
-void update_ebc_master_ios(void)
+void update_ebc_master_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
 {
 	gpio_tab[GPIO0][27].in_out = GPIO_IN;	    /* EXT_EBC_REQ */
 	gpio_tab[GPIO0][27].alt_nb = GPIO_ALT1;
@@ -1580,7 +1709,7 @@ void update_ebc_master_ios(void)
 /*----------------------------------------------------------------------------+
   | update_usb2_device_ios().
   +----------------------------------------------------------------------------*/
-void update_usb2_device_ios(void)
+void update_usb2_device_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
 {
 	gpio_tab[GPIO0][26].in_out = GPIO_IN;	    /* USB2D_RXVALID */
 	gpio_tab[GPIO0][26].alt_nb = GPIO_ALT2;
@@ -1611,20 +1740,21 @@ void update_usb2_device_ios(void)
 /*----------------------------------------------------------------------------+
   | update_pci_patch_ios().
   +----------------------------------------------------------------------------*/
-void update_pci_patch_ios(void)
+void update_pci_patch_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
 {
 	gpio_tab[GPIO0][29].in_out = GPIO_OUT;	    /* EBC_EXT_HDLA */
 	gpio_tab[GPIO0][29].alt_nb = GPIO_ALT1;
 }
 
 /*----------------------------------------------------------------------------+
-  |   set_chip_gpio_configuration(unsigned char gpio_core)
+  |   set_chip_gpio_configuration(unsigned char gpio_core,
+  |                               gpio_param_s (*gpio_tab)[GPIO_MAX])
   |   Put the core impacted by clock modification and sharing in reset.
   |   Config the select registers to resolve the sharing depending of the config.
   |   Configure the GPIO registers.
   |
   +----------------------------------------------------------------------------*/
-void set_chip_gpio_configuration(unsigned char gpio_core)
+void set_chip_gpio_configuration(unsigned char gpio_core, gpio_param_s (*gpio_tab)[GPIO_MAX])
 {
 	unsigned char i=0, j=0, reg_offset = 0;
 	unsigned long gpio_reg, gpio_core_add;
@@ -1778,11 +1908,12 @@ void configure_ppc440ep_pins(void)
 			CORE_NOT_SELECTED	/* PCI_PATCH */
 		};
 
+	gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX];
 
 	/* Table Default Initialisation + FPGA Access */
-	init_default_gpio();
-	set_chip_gpio_configuration(GPIO0);
-	set_chip_gpio_configuration(GPIO1);
+	init_default_gpio(gpio_tab);
+	set_chip_gpio_configuration(GPIO0, gpio_tab);
+	set_chip_gpio_configuration(GPIO1, gpio_tab);
 
 	/* Update Table */
 	force_bup_core_selection(ppc440ep_core_selection, &config_val);
@@ -1817,7 +1948,7 @@ void configure_ppc440ep_pins(void)
 	/* UIC 0:3 Selection */
 	if (ppc440ep_core_selection[UIC_0_3] == CORE_SELECTED)
 	{
-		update_uic_0_3_irq_ios();
+		update_uic_0_3_irq_ios(gpio_tab);
 		dma_a_b_unselect_in_fpga();
 	}
 
@@ -1825,21 +1956,21 @@ void configure_ppc440ep_pins(void)
 	if (ppc440ep_core_selection[UIC_4_9] == CORE_SELECTED)
 	{
 		sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_DIS_MASK) | SDR0_PFC1_DIS_UICIRQ5_SEL;
-		update_uic_4_9_irq_ios();
+		update_uic_4_9_irq_ios(gpio_tab);
 	}
 
 	/* DMA AB Selection */
 	if (ppc440ep_core_selection[DMA_CHANNEL_AB] == CORE_SELECTED)
 	{
 		sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_DIS_MASK) | SDR0_PFC1_DIS_DMAR_SEL;
-		update_dma_a_b_ios();
+		update_dma_a_b_ios(gpio_tab);
 		dma_a_b_selection_in_fpga();
 	}
 
 	/* DMA CD Selection */
 	if (ppc440ep_core_selection[DMA_CHANNEL_CD] == CORE_SELECTED)
 	{
-		update_dma_c_d_ios();
+		update_dma_c_d_ios(gpio_tab);
 		dma_c_d_selection_in_fpga();
 	}
 
@@ -1848,14 +1979,14 @@ void configure_ppc440ep_pins(void)
 	{
 		sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_ERE_MASK) | SDR0_PFC1_ERE_EXTR_SEL;
 		sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_EBCHR_SEL;
-		update_ebc_master_ios();
+		update_ebc_master_ios(gpio_tab);
 	}
 
 	/* PCI Patch Enable */
 	if (ppc440ep_core_selection[PCI_PATCH] == CORE_SELECTED)
 	{
 		sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_EBCHR_SEL;
-		update_pci_patch_ios();
+		update_pci_patch_ios(gpio_tab);
 	}
 
 	/* USB2 Host Selection - Not Implemented in PowerPC 440EP Pass1 */
@@ -1871,7 +2002,7 @@ void configure_ppc440ep_pins(void)
 	/* USB2.0 Device Selection */
 	if (ppc440ep_core_selection[USB2_DEVICE] == CORE_SELECTED)
 	{
-		update_usb2_device_ios();
+		update_usb2_device_ios(gpio_tab);
 		sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_USB2D_SEL;
 		sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UPR_MASK) | SDR0_PFC1_UPR_DISABLE;
 
@@ -1904,7 +2035,7 @@ void configure_ppc440ep_pins(void)
 	/* NAND Flash Selection */
 	if (ppc440ep_core_selection[NAND_FLASH] == CORE_SELECTED)
 	{
-		update_ndfc_ios();
+		update_ndfc_ios(gpio_tab);
 
 #if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL))
 		mtsdr(sdr_cust0, SDR0_CUST0_MUX_NDFC_SEL   |
@@ -1933,7 +2064,7 @@ void configure_ppc440ep_pins(void)
 	/* MII Selection */
 	if (ppc440ep_core_selection[MII_SEL] == CORE_SELECTED)
 	{
-		update_zii_ios();
+		update_zii_ios(gpio_tab);
 		mfsdr(sdr_mfr, sdr0_mfr);
 		sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_MII;
 		mtsdr(sdr_mfr, sdr0_mfr);
@@ -1944,7 +2075,7 @@ void configure_ppc440ep_pins(void)
 	/* RMII Selection */
 	if (ppc440ep_core_selection[RMII_SEL] == CORE_SELECTED)
 	{
-		update_zii_ios();
+		update_zii_ios(gpio_tab);
 		mfsdr(sdr_mfr, sdr0_mfr);
 		sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_RMII_10M;
 		mtsdr(sdr_mfr, sdr0_mfr);
@@ -1955,7 +2086,7 @@ void configure_ppc440ep_pins(void)
 	/* SMII Selection */
 	if (ppc440ep_core_selection[SMII_SEL] == CORE_SELECTED)
 	{
-		update_zii_ios();
+		update_zii_ios(gpio_tab);
 		mfsdr(sdr_mfr, sdr0_mfr);
 		sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_SMII;
 		mtsdr(sdr_mfr, sdr0_mfr);
@@ -1992,7 +2123,7 @@ void configure_ppc440ep_pins(void)
 		sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U1ME_MASK) | SDR0_PFC1_U1ME_DSR_DTR;
 		break;
 	}
-	update_uart_ios(uart_configuration);
+	update_uart_ios(uart_configuration, gpio_tab);
 
 	/* UART Selection in all cases */
 	uart_selection_in_fpga(uart_configuration);
@@ -2014,8 +2145,8 @@ void configure_ppc440ep_pins(void)
 
 	/* Perform effective access to hardware */
 	mtsdr(sdr_pfc1, sdr0_pfc1);
-	set_chip_gpio_configuration(GPIO0);
-	set_chip_gpio_configuration(GPIO1);
+	set_chip_gpio_configuration(GPIO0, gpio_tab);
+	set_chip_gpio_configuration(GPIO1, gpio_tab);
 
 	/* USB2.0 Device Reset must be done after GPIO setting */
 	if (ppc440ep_core_selection[USB2_DEVICE] == CORE_SELECTED)