net: mvneta: Convert to driver model

Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.

With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:

PHY-mode ("phy-mode") and PHY-address ("reg").

The base addresses for the ethernet controllers can be removed from
the header files as well.

Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>

1 files changed, 12 insertions, 20 deletions

diff --git a/board/Marvell/db-mv784mp-gp/db-mv784mp-gp.c b/board/Marvell/db-mv784mp-gp/db-mv784mp-gp.c
index d7aa1499ad..9305284117 100644
--- a/board/Marvell/db-mv784mp-gp/db-mv784mp-gp.c
+++ b/board/Marvell/db-mv784mp-gp/db-mv784mp-gp.c
@@ -87,40 +87,32 @@ int board_eth_init(bd_t *bis)
 	return pci_eth_init(bis);
 }
 
-#ifdef CONFIG_RESET_PHY_R
-/* Configure and enable MV88E1545 PHY */
-void reset_phy(void)
+int board_phy_config(struct phy_device *phydev)
 {
-	u8 phy_addr[] = CONFIG_PHY_ADDR;
-	u16 devadr = phy_addr[0];
-	char *name = "neta0";
 	u16 reg;
 
-	if (miiphy_set_current_dev(name))
-		return;
-
 	/* Enable QSGMII AN */
 	/* Set page to 4 */
-	miiphy_write(name, devadr, 0x16, 4);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x16, 4);
 	/* Enable AN */
-	miiphy_write(name, devadr, 0x0, 0x1140);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x0, 0x1140);
 	/* Set page to 0 */
-	miiphy_write(name, devadr, 0x16, 0);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x16, 0);
 
 	/* Phy C_ANEG */
-	miiphy_read(name, devadr, 0x4, &reg);
+	reg = phy_read(phydev, MDIO_DEVAD_NONE, 0x4);
 	reg |= 0x1E0;
-	miiphy_write(name, devadr, 0x4, reg);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x4, reg);
 
 	/* Soft-Reset */
-	miiphy_write(name, devadr, 22, 0x0000);
-	miiphy_write(name, devadr, 0, 0x9140);
+	phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x0000);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0, 0x9140);
 
 	/* Power up the phy */
-	miiphy_read(name, devadr, ETH_PHY_CTRL_REG, &reg);
+	reg = phy_read(phydev, MDIO_DEVAD_NONE, ETH_PHY_CTRL_REG);
 	reg &= ~(ETH_PHY_CTRL_POWER_DOWN_MASK);
-	miiphy_write(name, devadr, ETH_PHY_CTRL_REG, reg);
+	phy_write(phydev, MDIO_DEVAD_NONE, ETH_PHY_CTRL_REG, reg);
 
-	printf("88E1545 Initialized on %s\n", name);
+	printf("88E1545 Initialized\n");
+	return 0;
 }
-#endif /* CONFIG_RESET_PHY_R */