summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorJelle de Jong <jelledejong@powercraft.nl>2015-10-18 16:34:13 +0200
committerHans de Goede <hdegoede@redhat.com>2015-11-22 11:43:58 +0100
commitaa56cb374de8ae83f3280fdd6c280724228b86d7 (patch)
treeac5a696241c0bd0d01022e71759cc7ec1c415c6a
parent7e17fd26539417219e937e9f4eba491a23f83234 (diff)
downloadblackbird-obmc-uboot-aa56cb374de8ae83f3280fdd6c280724228b86d7.tar.gz
blackbird-obmc-uboot-aa56cb374de8ae83f3280fdd6c280724228b86d7.zip
sunxi: Add support for the Lamobo R1 board
The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such on the PCB, is meant as a A20 based router board. As such the board comes with a built-in switch chip giving it 5 gigabit ethernet ports, and it has a large empty area on the pcb with mounting holes which will fit a 2.5 inch harddisk. To complete its networking features it has a Realtek RTL8192CU for WiFi 802.11 b/g/n. The dts file is identical to the one submitted upstream. Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
-rw-r--r--arch/arm/dts/Makefile1
-rw-r--r--arch/arm/dts/sun7i-a20-lamobo-r1.dts297
-rw-r--r--board/sunxi/MAINTAINERS5
-rw-r--r--configs/Lamobo_R1_defconfig16
4 files changed, 319 insertions, 0 deletions
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index ca9c1964db..65e76ace90 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -147,6 +147,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-cubietruck.dtb \
sun7i-a20-hummingbird.dtb \
sun7i-a20-i12-tvbox.dtb \
+ sun7i-a20-lamobo-r1.dtb \
sun7i-a20-m3.dtb \
sun7i-a20-m5.dtb \
sun7i-a20-mk808c.dtb \
diff --git a/arch/arm/dts/sun7i-a20-lamobo-r1.dts b/arch/arm/dts/sun7i-a20-lamobo-r1.dts
new file mode 100644
index 0000000000..975b0b278b
--- /dev/null
+++ b/arch/arm/dts/sun7i-a20-lamobo-r1.dts
@@ -0,0 +1,297 @@
+/*
+ * Copyright 2015 Jelle de Jong <jelledejong@powercraft.nl>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Lamobo R1";
+ compatible = "lamobo,lamobo-r1", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart3;
+ serial2 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_lamobo_r1>;
+
+ green {
+ label = "lamobo_r1:green:usr";
+ gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_lamobo_r1>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */
+ };
+};
+
+&ahci_pwr_pin_a {
+ allwinner,pins = "PB3";
+};
+
+&ahci {
+ target-supply = <&reg_ahci_5v>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&reg_dcdc2>;
+ operating-points = <
+ /* kHz uV */
+ 960000 1400000
+ 912000 1400000
+ 864000 1350000
+ 720000 1250000
+ 528000 1150000
+ 312000 1100000
+ 144000 1050000
+ >;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <&reg_gmac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_rx_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_lamobo_r1>;
+ vmmc-supply = <&reg_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc0_cd_pin_lamobo_r1: mmc0_cd_pin@0 {
+ allwinner,pins = "PH10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ gmac_power_pin_lamobo_r1: gmac_power_pin@0 {
+ allwinner,pins = "PH23";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_lamobo_r1: led_pins@0 {
+ allwinner,pins = "PH24";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&reg_ahci_5v {
+ gpio = <&pio 1 3 0>; /* PB3 */
+ status = "okay";
+};
+
+&reg_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+&reg_usb0_vbus {
+ status = "okay";
+};
+
+&reg_usb1_vbus {
+ status = "okay";
+};
+
+&reg_usb2_vbus {
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>,
+ <&spi0_cs0_pins_a>,
+ <&spi0_cs1_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins_b>;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <&reg_usb0_vbus>;
+ usb1_vbus-supply = <&reg_usb1_vbus>;
+ usb2_vbus-supply = <&reg_usb2_vbus>;
+ status = "okay";
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index d9cda67f24..1f62de763a 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -121,6 +121,11 @@ M: Michal Suchanek <hramrach@gmail.com>
S: Maintained
F: configs/iNet_86VS_defconfig
+LAMOBO-R1 BOARD
+M: Jelle de Jong <jelledejong@powercraft.nl>
+S: Maintained
+F: configs/Lamobo_R1_defconfig
+
LINKSPRITE-PCDUINO BOARD
M: Zoltan Herpai <wigyori@uid0.hu>
S: Maintained
diff --git a/configs/Lamobo_R1_defconfig b/configs/Lamobo_R1_defconfig
new file mode 100644
index 0000000000..d460c3270b
--- /dev/null
+++ b/configs/Lamobo_R1_defconfig
@@ -0,0 +1,16 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN7I=y
+CONFIG_DRAM_CLK=432
+CONFIG_MMC0_CD_PIN="PH10"
+CONFIG_GMAC_TX_DELAY=4
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-lamobo-r1"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI,SATAPWR=SUNXI_GPB(3)"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_USB_EHCI_HCD=y
OpenPOWER on IntegriCloud