summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorBenoît Thébaudeau <benoit.thebaudeau@advansee.com>2013-05-03 10:32:16 +0000
committerStefano Babic <sbabic@denx.de>2013-05-05 17:55:03 +0200
commit97549cb54615ebddff03da8511a83d3855979ef6 (patch)
treeb7cbf3d553d36e1baf66ad0d2d565b15eca6dea0
parent1b1c526751d316aa1925d7aa8f5cee69201b0298 (diff)
downloadblackbird-obmc-uboot-97549cb54615ebddff03da8511a83d3855979ef6.tar.gz
blackbird-obmc-uboot-97549cb54615ebddff03da8511a83d3855979ef6.zip
imx: tx25: Convert to iomux-v3
There is no change of behavior, even if some pad control values could probably be simplified. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
-rw-r--r--board/karo/tx25/tx25.c107
1 files changed, 68 insertions, 39 deletions
diff --git a/board/karo/tx25/tx25.c b/board/karo/tx25/tx25.c
index 85719a0204..2952eba8c8 100644
--- a/board/karo/tx25/tx25.c
+++ b/board/karo/tx25/tx25.c
@@ -27,9 +27,8 @@
#include <common.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
-#include <asm/arch/imx25-pinmux.h>
+#include <asm/arch/iomux-mx25.h>
#include <asm/gpio.h>
-#include <asm/arch/sys_proto.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -42,36 +41,44 @@ void board_init_f(ulong bootflag)
#endif
#ifdef CONFIG_FEC_MXC
+/*
+ * FIXME: need to revisit this
+ * The original code enabled PUE and 100-k pull-down without PKE, so the right
+ * value here is likely:
+ * 0 for no pull
+ * or:
+ * PAD_CTL_PUS_100K_DOWN for 100-k pull-down
+ */
+#define FEC_OUT_PAD_CTRL 0
+
#define GPIO_FEC_RESET_B IMX_GPIO_NR(4, 7)
#define GPIO_FEC_ENABLE_B IMX_GPIO_NR(4, 9)
void tx25_fec_init(void)
{
- struct iomuxc_mux_ctl *muxctl;
- struct iomuxc_pad_ctl *padctl;
- u32 gpio_mux_mode = MX25_PIN_MUX_MODE(5);
- u32 saved_rdata0_mode, saved_rdata1_mode, saved_rx_dv_mode;
+ static const iomux_v3_cfg_t fec_pads[] = {
+ MX25_PAD_FEC_TX_CLK__FEC_TX_CLK,
+ MX25_PAD_FEC_RX_DV__FEC_RX_DV,
+ MX25_PAD_FEC_RDATA0__FEC_RDATA0,
+ NEW_PAD_CTRL(MX25_PAD_FEC_TDATA0__FEC_TDATA0, FEC_OUT_PAD_CTRL),
+ NEW_PAD_CTRL(MX25_PAD_FEC_TX_EN__FEC_TX_EN, FEC_OUT_PAD_CTRL),
+ NEW_PAD_CTRL(MX25_PAD_FEC_MDC__FEC_MDC, FEC_OUT_PAD_CTRL),
+ MX25_PAD_FEC_MDIO__FEC_MDIO,
+ MX25_PAD_FEC_RDATA1__FEC_RDATA1,
+ NEW_PAD_CTRL(MX25_PAD_FEC_TDATA1__FEC_TDATA1, FEC_OUT_PAD_CTRL),
+
+ NEW_PAD_CTRL(MX25_PAD_D13__GPIO_4_7, 0), /* FEC_RESET_B */
+ NEW_PAD_CTRL(MX25_PAD_D11__GPIO_4_9, 0), /* FEC_ENABLE_B */
+ };
+
+ static const iomux_v3_cfg_t fec_cfg_pads[] = {
+ MX25_PAD_FEC_RDATA0__GPIO_3_10,
+ MX25_PAD_FEC_RDATA1__GPIO_3_11,
+ MX25_PAD_FEC_RX_DV__GPIO_3_12,
+ };
debug("tx25_fec_init\n");
- /*
- * fec pin init is generic
- */
- mx25_fec_init_pins();
-
- /*
- * Set up the FEC_RESET_B and FEC_ENABLE GPIO pins.
- *
- * FEC_RESET_B: gpio4[7] is ALT 5 mode of pin D13
- * FEC_ENABLE_B: gpio4[9] is ALT 5 mode of pin D11
- */
- muxctl = (struct iomuxc_mux_ctl *)IMX_IOPADMUX_BASE;
- padctl = (struct iomuxc_pad_ctl *)IMX_IOPADCTL_BASE;
-
- writel(gpio_mux_mode, &muxctl->pad_d13);
- writel(gpio_mux_mode, &muxctl->pad_d11);
-
- writel(0x0, &padctl->pad_d13);
- writel(0x0, &padctl->pad_d11);
+ imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
/* drop PHY power and assert reset (low) */
gpio_direction_output(GPIO_FEC_RESET_B, 0);
@@ -99,15 +106,10 @@ void tx25_fec_init(void)
* RMII mode is selected by FEC_RX_DV which is GPIO 3_12 in mux mode
*/
/*
- * save three current mux modes and set each to gpio mode
+ * set each mux mode to gpio mode
*/
- saved_rdata0_mode = readl(&muxctl->pad_fec_rdata0);
- saved_rdata1_mode = readl(&muxctl->pad_fec_rdata1);
- saved_rx_dv_mode = readl(&muxctl->pad_fec_rx_dv);
-
- writel(gpio_mux_mode, &muxctl->pad_fec_rdata0);
- writel(gpio_mux_mode, &muxctl->pad_fec_rdata1);
- writel(gpio_mux_mode, &muxctl->pad_fec_rx_dv);
+ imx_iomux_v3_setup_multiple_pads(fec_cfg_pads,
+ ARRAY_SIZE(fec_cfg_pads));
/*
* set each to 1 and make each an output
@@ -128,19 +130,46 @@ void tx25_fec_init(void)
/*
* set FEC pins back
*/
- writel(saved_rdata0_mode, &muxctl->pad_fec_rdata0);
- writel(saved_rdata1_mode, &muxctl->pad_fec_rdata1);
- writel(saved_rx_dv_mode, &muxctl->pad_fec_rx_dv);
+ imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
}
#else
#define tx25_fec_init()
#endif
-int board_init()
-{
#ifdef CONFIG_MXC_UART
- mx25_uart1_init_pins();
+/*
+ * Set up input pins with hysteresis and 100-k pull-ups
+ */
+#define UART1_IN_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP)
+/*
+ * FIXME: need to revisit this
+ * The original code enabled PUE and 100-k pull-down without PKE, so the right
+ * value here is likely:
+ * 0 for no pull
+ * or:
+ * PAD_CTL_PUS_100K_DOWN for 100-k pull-down
+ */
+#define UART1_OUT_PAD_CTRL 0
+
+static void tx25_uart1_init(void)
+{
+ static const iomux_v3_cfg_t uart1_pads[] = {
+ NEW_PAD_CTRL(MX25_PAD_UART1_RXD__UART1_RXD, UART1_IN_PAD_CTRL),
+ NEW_PAD_CTRL(MX25_PAD_UART1_TXD__UART1_TXD, UART1_OUT_PAD_CTRL),
+ NEW_PAD_CTRL(MX25_PAD_UART1_RTS__UART1_RTS, UART1_OUT_PAD_CTRL),
+ NEW_PAD_CTRL(MX25_PAD_UART1_CTS__UART1_CTS, UART1_IN_PAD_CTRL),
+ };
+
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+#else
+#define tx25_uart1_init()
#endif
+
+int board_init()
+{
+ tx25_uart1_init();
+
/* board id for linux */
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
return 0;
OpenPOWER on IntegriCloud