diff options
| author | Detlev Zundel <dzu@denx.de> | 2009-10-07 16:38:05 +0200 |
|---|---|---|
| committer | Wolfgang Denk <wd@denx.de> | 2009-10-08 00:31:23 +0200 |
| commit | 95c44ec485b46ffb43dbdaa299f1491a500fdadf (patch) | |
| tree | 8a1f5082e04ea422be70b0a39baa9fc4c79fa4fe | |
| parent | da01f53404f99db185d196867af79371725d4683 (diff) | |
| download | blackbird-obmc-uboot-95c44ec485b46ffb43dbdaa299f1491a500fdadf.tar.gz blackbird-obmc-uboot-95c44ec485b46ffb43dbdaa299f1491a500fdadf.zip | |
tqm5200: Correct comment and code in post_hotkeys_pressed.
This fixes the code and the comment according to the original intent of
doing an intensive memory test when PSC6_3 is pulled low on the STK52xx.
Notably PORT_CONFIG will be overridden with this correct code now,
so beware.
The original code only worked by coincidence depending on the PORT_CONFIG
setting from the header file. The new code was tested to ensure that the
(undocumented) memory test still works on the STK52x.
Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Martin Krause <Martin.Krause@tqs.de>
Minor white-space cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
| -rw-r--r-- | board/tqc/tqm5200/tqm5200.c | 6 | ||||
| -rw-r--r-- | include/configs/TQM5200.h | 14 |
2 files changed, 10 insertions, 10 deletions
diff --git a/board/tqc/tqm5200/tqm5200.c b/board/tqc/tqm5200/tqm5200.c index faa2e02191..5a091c40d7 100644 --- a/board/tqc/tqm5200/tqm5200.c +++ b/board/tqc/tqm5200/tqm5200.c @@ -358,11 +358,9 @@ int post_hotkeys_pressed(void) gpio = (struct mpc5xxx_gpio*) MPC5XXX_GPIO; /* - * Configure PSC6_1 and PSC6_3 as GPIO. PSC6 then couldn't be used in - * CODEC or UART mode. Consumer IrDA should still be possible. + * Configure PSC6_0 through PSC6_3 as GPIO. */ - gpio->port_config &= ~(0x07000000); - gpio->port_config |= 0x03000000; + gpio->port_config &= ~(0x00700000); /* Enable GPIO for GPIO_IRDA_1 (IR_USB_CLK pin) = PSC6_3 */ gpio->simple_gpioe |= 0x20000000; diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index a4336a7500..2154c7870e 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -540,6 +540,8 @@ * 101 -> use PSC6 as UART. Pins PSC6_0 to PSC6_3 are used. * Extended POST test is not available. * Use for STK52xx, FO300 and CAM5200 boards. + * WARNING: When the extended POST is enabled, these bits will + * be overridden by this code as GPIOs! * use PCI_DIS: Bit 16 (mask 0x00008000): * 1 -> disable PCI controller (on CAM5200 board). * use USB: Bits 18-19 (mask 0x00003000): @@ -552,7 +554,7 @@ * 000 -> All PSC2 pins are GPIOs. * 100 -> UART (on CAM5200 board). * 001 -> CAN1/2 on PSC2 pins. - * Use for REV100 STK52xx boards + * Use for REV100 STK52xx boards * 01x -> Use AC97 (on FO300 board). * use PSC1: Bits 29-31 (mask: 0x00000007): * 100 -> UART (on all boards). @@ -711,20 +713,20 @@ #define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA -/* Offset for data I/O */ +/* Offset for data I/O */ #define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) -/* Offset for normal register accesses */ +/* Offset for normal register accesses */ #define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) -/* Offset for alternate registers */ +/* Offset for alternate registers */ #define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) -/* Interval between registers */ +/* Interval between registers */ #define CONFIG_SYS_ATA_STRIDE 4 /* Support ATAPI devices */ -#define CONFIG_ATAPI 1 +#define CONFIG_ATAPI 1 /*----------------------------------------------------------------------- * Open firmware flat tree support |
