From d436641439e0121d26b19d4268e9fb3ecd368d71 Mon Sep 17 00:00:00 2001 From: Jens Axboe Date: Mon, 14 Mar 2016 09:06:01 -0600 Subject: cpqarray: remove it from the kernel We disabled the ability to enable this driver back in October of 2013, we should be able to safely remove it at this point. The initial goal was to remove it in 3.15, so now is the time. Signed-off-by: Jens Axboe --- Documentation/blockdev/cpqarray.txt | 93 ------------------------------------- 1 file changed, 93 deletions(-) delete mode 100644 Documentation/blockdev/cpqarray.txt (limited to 'Documentation/blockdev') diff --git a/Documentation/blockdev/cpqarray.txt b/Documentation/blockdev/cpqarray.txt deleted file mode 100644 index c7154e20ef5e..000000000000 --- a/Documentation/blockdev/cpqarray.txt +++ /dev/null @@ -1,93 +0,0 @@ -This driver is for Compaq's SMART2 Intelligent Disk Array Controllers. - -Supported Cards: ----------------- - -This driver is known to work with the following cards: - - * SMART (EISA) - * SMART-2/E (EISA) - * SMART-2/P - * SMART-2DH - * SMART-2SL - * SMART-221 - * SMART-3100ES - * SMART-3200 - * Integrated Smart Array Controller - * SA 4200 - * SA 4250ES - * SA 431 - * RAID LC2 Controller - -It should also work with some really old Disk array adapters, but I am -unable to test against these cards: - - * IDA - * IDA-2 - * IAES - - -EISA Controllers: ------------------ - -If you want to use an EISA controller you'll have to supply some -modprobe/lilo parameters. If the driver is compiled into the kernel, must -give it the controller's IO port address at boot time (it is not -necessary to specify the IRQ). For example, if you had two SMART-2/E -controllers, in EISA slots 1 and 2 you'd give it a boot argument like -this: - - smart2=0x1000,0x2000 - -If you were loading the driver as a module, you'd give load it like this: - - modprobe cpqarray eisa=0x1000,0x2000 - -You can use EISA and PCI adapters at the same time. - - -Device Naming: --------------- - -You need some entries in /dev for the ida device. MAKEDEV in the /dev -directory can make device nodes for you automatically. The device setup is -as follows: - -Major numbers: - 72 ida0 - 73 ida1 - 74 ida2 - 75 ida3 - 76 ida4 - 77 ida5 - 78 ida6 - 79 ida7 - -Minor numbers: - b7 b6 b5 b4 b3 b2 b1 b0 - |----+----| |----+----| - | | - | +-------- Partition ID (0=wholedev, 1-15 partition) - | - +-------------------- Logical Volume number - -The device naming scheme is: -/dev/ida/c0d0 Controller 0, disk 0, whole device -/dev/ida/c0d0p1 Controller 0, disk 0, partition 1 -/dev/ida/c0d0p2 Controller 0, disk 0, partition 2 -/dev/ida/c0d0p3 Controller 0, disk 0, partition 3 - -/dev/ida/c1d1 Controller 1, disk 1, whole device -/dev/ida/c1d1p1 Controller 1, disk 1, partition 1 -/dev/ida/c1d1p2 Controller 1, disk 1, partition 2 -/dev/ida/c1d1p3 Controller 1, disk 1, partition 3 - - -Changelog: -========== - -10-28-2004 : General cleanup, syntax fixes for in-kernel driver version. - James Nelson - - -1999 : Original Document -- cgit v1.2.1