| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This reverts commit dc911f5bd8aacfcf8aabd5c26c88e04c837a938e.
Per the report, no matter what display mode you select with xrandr, the
i915 driver will always select the alternate fixed mode. For the
reporter this means that the display will always run at 40Hz which is
quite annoying. This may be due to the mode comparison.
But there are some other potential issues. The choice of alt_fixed_mode
seems dubious. It's the first non-preferred mode, but there are no
guarantees that the only difference would be refresh rate. Similarly,
there may be more than one preferred mode in the probed modes list, and
the commit changes the preferred mode selection to choose the last one
on the list instead of the first.
(Note that the probed modes list is the raw, unfiltered, unsorted list
of modes from drm_add_edid_modes(), not the pretty result after a
drm_helper_probe_single_connector_modes() call.)
Finally, we already have eerily similar code in place to find the
downclock mode for DRRS that seems like could be reused here.
Back to the drawing board.
Note: This is a hand-crafted revert due to conflicts. If it fails to
backport, please just try reverting the original commit directly.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105469
Reported-by: Rune Petersen <rune@megahurts.dk>
Reported-by: Mark Spencer <n7u4722r35@ynzlx.anonbox.net>
Fixes: dc911f5bd8aa ("drm/i915/edp: Allow alternate fixed mode for eDP if available.")
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180516080110.22770-1-jani.nikula@intel.com
(cherry picked from commit d93fa1b47b8fcd149b5091f18385304f402a8e15)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On intel_dp_compute_config() we were calculating the needed vco
for eDP on gen9 and we stashing it in
intel_atomic_state.cdclk.logical.vco
However few moments later on intel_modeset_checks() we fully
replace entire intel_atomic_state.cdclk.logical with
dev_priv->cdclk.logical fully overwriting the logical desired
vco for eDP on gen9.
So, with wrong VCO value we end up with wrong desired cdclk, but
also it will raise a lot of WARNs: On gen9, when we read
CDCLK_CTL to verify if we configured properly the desired
frequency the CD Frequency Select bits [27:26] == 10b can mean
337.5 or 308.57 MHz depending on the VCO. So if we have wrong
VCO value stashed we will believe the frequency selection didn't
stick and start to raise WARNs of cdclk mismatch.
[ 42.857519] [drm:intel_dump_cdclk_state [i915]] Changing CDCLK to 308571 kHz, VCO 8640000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
[ 42.897269] cdclk state doesn't match!
[ 42.901052] WARNING: CPU: 5 PID: 1116 at drivers/gpu/drm/i915/intel_cdclk.c:2084 intel_set_cdclk+0x5d/0x110 [i915]
[ 42.938004] RIP: 0010:intel_set_cdclk+0x5d/0x110 [i915]
[ 43.155253] WARNING: CPU: 5 PID: 1116 at drivers/gpu/drm/i915/intel_cdclk.c:2084 intel_set_cdclk+0x5d/0x110 [i915]
[ 43.170277] [drm:intel_dump_cdclk_state [i915]] [hw state] 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
[ 43.182566] [drm:intel_dump_cdclk_state [i915]] [sw state] 308571 kHz, VCO 8640000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
v2: Move the entire eDP's vco logical adjustment to inside
the skl_modeset_calc_cdclk as suggested by Ville.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: bb0f4aab0e76 ("drm/i915: Track full cdclk state for the logical and actual cdclk frequencies")
Cc: <stable@vger.kernel.org> # v4.12+
Link: https://patchwork.freedesktop.org/patch/msgid/20180502175255.5344-1-rodrigo.vivi@intel.com
|
|
|
|
|
|
|
|
|
|
|
| |
Abstract compliance test adjustments to a single function. Also make the
bpc adjustments affect the limits, actually forcing the bpc. Seems like
directly changing the pipe_bpp in the past could not have been
effective.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ef61e76003ab7719c82810b742f3fb5765c0e14c.1524730974.git.jani.nikula@intel.com
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
For now, there's just the one link config selection, optimizing for slow
and wide link. No functional changes.
Keep the debug logging in the caller, to avoid duplication later on if
alternative link confing selection gets added.
v2: Improved commit message
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/64848b76bf90d6ceecd7ec6b5add28531e0b1a41.1524730974.git.jani.nikula@intel.com
|
|
|
|
|
|
|
|
|
| |
Also use same min/max model for bpp, and adjust debug logging while at
it.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/72f78c7ae0cd1810798bd94cbf5e574c78da83f8.1524730974.git.jani.nikula@intel.com
|
|
|
|
|
|
|
|
|
|
| |
Keep related things together. No functional changes.
v2: Fix a typo in patch subject, fix a checkpatch alignment warning.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f24d44547a586a0e342f24e69ab4d576a2474891.1524730974.git.jani.nikula@intel.com
|
|
|
|
|
|
|
|
|
|
|
|
| |
Abstract a new intel_dp_compute_link_config() from
intel_dp_compute_config(), with the parts related to link configuration,
i.e. bpp, link rate, and lane count selection. No functional changes.
v2: Fix a checkpatch warn about spacing.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/80f99a625633f87f44d38d487ba3b32ff9a26b07.1524730974.git.jani.nikula@intel.com
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We call intel_dp_compute_rate() in intel_dp_compute_config() only to be
able to debug log the link_bw and rate_select parameters; we don't use
the parameters here for anything else. We call intel_dp_compute_rate()
again during link training where we actually need and use the
parameters.
Move the debug logging of link_bw and rate_select to
intel_dp_link_training_clock_recovery(), and clean up the extra
intel_dp_compute_rate() call and extra clutter from the already
overcrowded intel_dp_compute_config().
v2: Rewrote commit message (Rodrigo, Manasi)
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c5cf6a179e2d244eceb6bb80a792765d9efbee4f.1524730974.git.jani.nikula@intel.com
|
|
|
|
|
|
|
|
|
|
| |
We haven't used the DP bw constants here for a while. No functional
changes.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1dc7763cdc70c7f64c0a01f76f218d9ac0717227.1524730974.git.jani.nikula@intel.com
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
AFAIK CHV was supposed to have HBR2 originally, but in the end the feature
was dropped. We still have some code leftovers from those early days.
Eliminate them.
The extra bit for the training pattern seems to be dead in the hardware.
I can set it (in fact I can set almost any reserved bit in the
registers) but it doesn't seem to interfere with the operation of the
hardware. Either that or I'm very lucky that my displays complete link
training with the incorrect pattern being sent out.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302095656.19662-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
|
|
|
|
|
|
|
|
| |
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308232421.14049-2-lyude@redhat.com
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
LSPCON likes to throw short HPDs during the enable seqeunce prior to the
link being trained. These obviously result in the channel CR/EQ check
failing and thus we schedule a pointless hotplug work to retrain the
link. Avoid that by ignoring the bad CR/EQ status until we've actually
initially trained the link.
I've not actually investigated to see what LSPCON is trying to signal
with the short pulse. But as long as it signals anything I think we're
supposed to check the link status anyway, so I don't really see other
good ways to solve this. I've not seen these short pulses being
generated by normal DP sinks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-5-ville.syrjala@linux.intel.com
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Doing link retraining from the short pulse handler is problematic since
that might introduce deadlocks with MST sideband processing. Currently
we don't retrain MST links from this code, but we want to change that.
So better to move the entire thing to the hotplug work. We can utilize
the new encoder->hotplug() hook for this.
The only thing we leave in the short pulse handler is the link status
check. That one still depends on the link parameters stored under
intel_dp, so no locking around that but races should be mostly harmless
as the actual retraining code will recheck the link state if we
end up there by mistake.
v2: Rebase due to ->post_hotplug() now being just ->hotplug()
Check the connector type to figure out if we should do
the HDMI thing or the DP think for DDI
[pushed with whitespace changes for sparse]
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-3-ville.syrjala@linux.intel.com
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The LG 4k TV I have doesn't deassert HPD when I turn the TV off, but
when I turn it back on it will pulse the HPD line. By that time it has
forgotten everything we told it about scrambling and the clock ratio.
Hence if we want to get a picture out if it again we have to tell it
whether we're currently sending scrambled data or not. Implement
that via the encoder->hotplug() hook.
v2: Force a full modeset to not follow the HDMI 2.0 spec more
closely (Shashank)
[pushed with whitespace fixes to make sparse happy]
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-1-ville.syrjala@linux.intel.com
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We have two instances of the code to fill out the header for the aux
message. Pull it into a small helper.
v2: Rebase due to txbuf[] changes
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222212802.4826-1-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Let's try to keep the details on the AKSV stuff concentrated
in one place. So move the control bit and +5 data size handling
there.
v2: Increase txbuf[] to include the payload which intel_dp_aux_xfer()
will still load into the registers even though the hardware
will ignore it
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222212732.4665-1-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
|
|
|
|
|
|
|
|
|
| |
Rename intel_dp_aux_ch() to intel_dp_aux_xfer() to better convey
what it actually does.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-6-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #irc
|
|\
| |
| |
| |
| |
| |
| | |
To pull in the HDCP changes, especially wait_for changes to drm/i915
that Chris wants to build on top of.
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
| |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://anongit.freedesktop.org/drm/drm-intel into drm-next
Driver Changes:
- Lift alpha_support protection from Cannonlake (Rodrigo)
* Meaning the driver should mostly work for the hardware we had
at our disposal when testing
* Used to be preliminary_hw_support
- Add missing Cannonlake PCI device ID of 0x5A4C (Rodrigo)
- Cannonlake port register fix (Mahesh)
- Fix Dell Venue 8 Pro black screen after modeset (Hans)
- Fix for always returning zero out-fence from execbuf (Daniele)
- Fix HDMI audio when no no relevant video output is active (Jani)
- Fix memleak of VBT data on driver_unload (Hans)
- Fix for KASAN found locking issue (Maarten)
- RCU barrier consolidation to improve igt/gem_sync/idle (Chris)
- Optimizations to IRQ handlers (Chris)
- vblank tracking improvements (64-bit resolution, PM) (Dhinakaran)
- Pipe select bit corrections (Ville)
- Reduce runtime computed device_info fields (Chris)
- Tune down some WARN_ONs to GEM_BUG_ON now that CI has good coverage (Chris)
- A bunch of kerneldoc warning fixes (Chris)
* tag 'drm-intel-next-2018-02-21' of git://anongit.freedesktop.org/drm/drm-intel: (113 commits)
drm/i915: Update DRIVER_DATE to 20180221
drm/i915/fbc: Use PLANE_HAS_FENCE to determine if the plane is fenced
drm/i915/fbdev: Use the PLANE_HAS_FENCE flags from the time of pinning
drm/i915: Move the policy for placement of the GGTT vma into the caller
drm/i915: Also check view->type for a normal GGTT view
drm/i915: Drop WaDoubleCursorLP3Latency:ivb
drm/i915: Set the primary plane pipe select bits on gen4
drm/i915: Don't set cursor pipe select bits on g4x+
drm/i915: Assert that we don't overflow frontbuffer tracking bits
drm/i915: Track number of pending freed objects
drm/i915/: Initialise trans_min for skl_compute_transition_wm()
drm/i915: Clear the in-use marker on execbuf failure
drm/i915: Prune gen8_gt_irq_handler
drm/i915: Track GT interrupt handling using the master iir
drm/i915: Remove WARN_ONCE for failing to pm_runtime_if_in_use
drm: intel_dpio_phy: fix kernel-doc comments at nested struct
drm/i915: Release connector iterator on a digital port conflict.
drm/i915/execlists: Remove too early assert
drm/i915: Assert that we always complete a submission to guc/execlists
drm: move read_domains and write_domain into i915
...
|
| |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://anongit.freedesktop.org/drm/drm-misc into drm-next
Add HDCP support to i915 drm driver.
* tag 'topic/hdcp-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc: (26 commits)
drm/i915: fix misalignment in HDCP register def
drm/i915: Reauthenticate HDCP on failure
drm/i915: Detect panel's hdcp capability
drm/i915: Optimize HDCP key load
drm/i915: Retry HDCP bksv read
drm/i915: Connector info in HDCP debug msgs
drm/i915: Stop encryption for repeater with no sink
drm/i915: Handle failure from 2nd stage HDCP auth
drm/i915: Downgrade hdcp logs from INFO to DEBUG_KMS
drm/i915: Restore HDCP DRM_INFO when with no downstream
drm/i915: Check for downstream topology errors
drm/i915: Start repeater auth on READY/CP_IRQ
drm/i915: II stage HDCP auth for repeater only
drm/i915: Extending HDCP for HSW, BDW and BXT+
drm/i915/dp: Fix compilation of intel_dp_hdcp_check_link
drm/i915: Only disable HDCP when it's active
drm/i915: Don't allow HDCP on PORT E/F
drm/i915: Implement HDCP for DisplayPort
drm/i915: Implement HDCP for HDMI
drm/i915: Add function to output Aksv over GMBUS
...
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
DP HDCP1.4 spec mandates that An can be written to panel only after
detecting the panel's hdcp capability.
For DP 0th Bit of Bcaps register indicates the panel's hdcp capability
For HDMI valid BKSV indicates the panel's hdcp capability.
For HDMI it is optional to detect the panel's hdcp capability before
An Write.
v2:
Added comments explaining the need for action [Seanpaul].
Made panel's hdcp capability detection optional for hdmi [Seanpaul].
Defined a func for reading bcaps for DP [Seanpaul].
v3:
Removed the NULL initialization [Seanpaul].
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1517609350-10698-7-git-send-email-ramalingam.c@intel.com
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch extends the Key load process and hdcp initialization for
few more capable intel platforms i.e. HSW, BDW and BXT+.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
[seanpaul fixed checkpatch issues]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1516254488-4971-2-git-send-email-ramalingam.c@intel.com
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
drivers/gpu/drm/i915/intel_dp.c: In function ‘intel_dp_hdcp_check_link’:
drivers/gpu/drm/i915/intel_dp.c:5191:26: error: ?: using integer constants in boolean context [-Werror=int-in-bool-context]
return ret >= 0 ? -EIO : ret;
Fixes: 20f24d776d1b ("drm/i915: Implement HDCP for DisplayPort")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180118161025.22700-1-chris@chris-wilson.co.uk
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch adds HDCP support for DisplayPort connectors by implementing
the intel_hdcp_shim.
Most of this is straightforward read/write from/to DPCD registers. One
thing worth pointing out is the Aksv output bit. It wasn't easily
separable like it's HDMI counterpart, so it's crammed in with the rest
of it.
Changes in v2:
- Moved intel_hdcp_check_link out of intel_dp_check_link and only call
it on short pulse. Since intel_hdcp_check_link does its own locking,
this ensures we don't deadlock when intel_dp_check_link is called
holding connection_mutex.
- Rebased on drm-intel-next
Changes in v3:
- Initialize new worker
Changes in v4:
- Use intel_hdcp_init (Daniel)
- Check for reauth requests in check_link (Ram)
Changes in v5:
- None
Changes in v6:
- Fix build warnings when printing ssize_t
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180108195545.218615-10-seanpaul@chromium.org
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
dp_rates[] array is a superset of all the link rates supported
by sink devices. DP 1.3 specification adds HBR3 (8.1Gbps) link rate
to the set of link rates supported by sink. This patch adds this rate
to dp_rates[] array that gets used to populate the sink_rates[]
array limited by max rate obtained from DP_MAX_LINK_RATE DPCD register.
v2:
* Rebased on top of Jani's localized rates patch
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1519857110-26916-1-git-send-email-manasi.d.navare@intel.com
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Localize link rate arrays by moving them to the functions where they're
used. Further clarify the distinction between source and sink
capabilities. Split pre and post Haswell arrays, and get rid of the
array size arithmetics. Use a direct rate value in the paranoia case of
no common rates find.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227105911.4485-1-jani.nikula@intel.com
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
While it seems totally unlikely that any system would mix a cpu/north
aux channel with a pch/south port (or vice versa) we should still
consult intel_dp->aux_ch rather than encoder->port when figuring out
which clock is actually used by the aux ch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-5-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #irc
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Currently, BXT_PP is hardcoded with value '0'.
It practically disabled eDP backlight on MRB (BXT) platform.
This patch will tell which BXT_PP registers (there are two set of
PP_CONTROL in the spec) to be used as defined in VBT (Video Bios Timing
table) and this will enabled eDP backlight controller on MRB (BXT)
platform.
v2:
- Remove unnecessary information in commit message.
- Assign vbt.backlight.controller to a backlight_controller variable and
return the variable value.
v3:
- Rebased to latest code base.
- updated commit title.
Signed-off-by: Mustamin B Mustaffa <mustamin.b.mustaffa@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227030734.37901-1-mustamin.b.mustaffa@intel.com
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
No functional change.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223221520.18464-6-dhinakaran.pandiyan@intel.com
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The core already takes care of the delay before retrying. The delay now
changes to (500, 600)us instead of (500 + 1000, 600 + 1500)us.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223221520.18464-5-dhinakaran.pandiyan@intel.com
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
intel_edp_init_dpcd() is cluttered with PSR specific DPCD checks and
intel_dp.c is huge.
No functional change intended.
v2: Rebased.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223221520.18464-3-dhinakaran.pandiyan@intel.com
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The usual if ladder order should be from newest to oldest
platform. However the CNL conditional statement was misplaced.
This patch sets the DP source for platforms starting from the newest
to oldest.
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1519701075-9894-1-git-send-email-manasi.d.navare@intel.com
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Collect all the aux ch vfunc assignments into intel_dp_aux_init()
instead of having it spread around.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-4-ville.syrjala@linux.intel.com
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Just store function pointers that give us the correct register offsets
instead of storing the register offsets themselves. Slightly less
efficient perhaps but saves a few bytes and better matches how we do
things elsewhere.
v2: Keep a local array of data registers (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-3-ville.syrjala@linux.intel.com
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Since we no longer have a 1:1 correspondence between ports and AUX
channels, let's give AUX channels their own enum. Makes it easier
to tell the apples from the oranges, and we get rid of the
port E AUX power domain FIXME since we now derive the power domain
from the actual AUX CH.
v2: Rebase due to AUX F
v3: Split out the power domain fix (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> #v2
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-2-ville.syrjala@linux.intel.com
|
| |_|/
|/| |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Select the aux power domain based on the aux ch rather than based on
the port. Now we can rid ourselves of the port E FIXME as well.
v2: Split from the enum aux_ch patch (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> #v1
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-1-ville.syrjala@linux.intel.com
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
While the comment singles out Port A or B, the code says Port A or *D*.
Looking at the history it seems that the comment was added after the code,
so it seems likely that the code is correct, not the comment.
CC: Jani Nikula <jani.nikula@intel.com>
CC: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180209130755.11893-1-david.weinehall@linux.intel.com
|
|/ /
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Coccinelle patch:
@@
identifier p;
@@
-INTEL_INFO(p)->gen
+INTEL_GEN(p)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180208130606.15556-12-tvrtko.ursulin@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180209215847.6660-1-chris@chris-wilson.co.uk
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We have the max DP link rate info available in VBT since BDB version
216, included in child device config since commit c4fb60b9aba9
("drm/i915/bios: add DP max link rate to VBT child device
struct"). Parse it and use it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a8b1364d1f2394fba3062b6ad11b474744ea4366.1517482774.git.jani.nikula@intel.com
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Make the limiting rate based instead of messing with the array size.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cb03b9419191a7d6359bf371aacb2d3725c746de.1517482774.git.jani.nikula@intel.com
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This will be useful later on. Also move the functions around to not need
forward declarations in subsequent patches. No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/40f37f08cad33234cd86337d39e823ac6e55805f.1517482774.git.jani.nikula@intel.com
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
On CNL SKUs that uses port F, max DP rate is 8.1G for all
ports when we have the elevated voltage (higher than 0.85V).
v2: Make commit message more generic.
v3: Move conditions to a helper to get easier to read. (Ville).
v4: Add a mention to the numerical voltage on commit
message per Manasi request.
v5: Thanks CI! "error: control reaches end of non-void function"
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-10-rodrigo.vivi@intel.com
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Now let's finish the Port-F support by adding the
proper port F detection, irq and power well support.
v2: Rebase
v3: Use BIT_ULL
v4: Cover missed case on ddi init.
v5: Update commit message.
v6: Rebase on top of display headers rework.
v7: Squash power-well handling related to DDI F to this
patch to avoid warns as pointed out by DK.
v8: Introduce DDI_F_LANES to PG2. (DK)
v9: Squash in the PORT_F case for enabling DP MST encoder. (DK)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-9-rodrigo.vivi@intel.com
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
On CNP boards that are using DDI F,
bit 25 (SDE_PORTE_HOTPLUG_SPT) is representing
the Digital Port F hotplug line when the Digital
Port F hotplug detect input is enabled.
v2: Reuse all existent structure instead of adding a
new HPD_PORT_F pointing to pin of port E.
v3: Use IS_CNL_WITH_PORT_F so we can start upstreaming
this right now. If that SKU ever get a proper name
we come back and update it.
v4: Rebase on top of digital connected port using encoder
instead of port.
v5: Moved IS_CNL_WITH_PORT_F definition to the PCI IDs patch.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-8-rodrigo.vivi@intel.com
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Let's try to simplify this mapping to hpd_pin -> bit
instead using port.
So for CNL with port F where we have this port using
hdp_pin and bits of other ports we don't need to duplicated
the mapping.
But for now this is only a re-org with no functional change
expected.
v2: Add missing lines and nuke @port reference from code
documentation. (Ville)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-7-rodrigo.vivi@intel.com
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
On some Cannonlake SKUs we have a dedicated Aux for port F,
that is only the full split between port A and port E.
There is still no Aux E for Port E, as in previous platforms,
because port_E still means shared lanes with port A.
v2: Rebase.
v3: Add couple missed PORT_F cases on intel_dp.
v4: Rebase and fix commit message.
v5: Squash Imre's "drm/i915: Add missing AUX_F power well string"
v6: Rebase on top of display headers rework.
v7: s/IS_CANNONLAKE/IS_CNL_WITH_PORT_F (DK)
v8: Fix Aux bits for Port F (DK)
v9: Fix VBT definition of Port F (DK).
v10: Squash power well addition to this patch to avoid
warns as pointed by DK.
v11: Clean up squashed commit message. (David)
v12: Remove unnecessary handling for older platforms (DK)
Adding AUX_F to PG2 following other existent ones. (DK)
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-2-rodrigo.vivi@intel.com
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
ICP, like BXT, has has two panel power sequencers.
v2: Simplify the code. Remove unwanted register definitions.
Make code as close to BXT style as possible. (Ville)
Also, remove the use of ICP_SECOND_PPS_BACKLIGHT for now.
Moving forward, if we are sure we need to set this register,
we can access it.
v3: Use INTEL_GEN(dev_priv), make code more readeable. (Ville)
v4 (from Paulo):
- Coding style fixes.
- Add a missing HAS_PCH_CNP -> gen10+ check.
- Rebase.
v5: Use per platform checks rather than INTEL_GEN().
v4 of this patch breaks on CoffeeLake, since CFL uses
CNP and per platform check makes sense in that case.
v6 (from Paulo):
- v5 was a patch on top of v4, not a new version. Now v6 is correctly
a new version of the original patch.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-6-paulo.r.zanoni@intel.com
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Some Cannonlake SKUs will come with a full split between
port A and port E. This will be called port F although it
is not a 6th port, but only a split.
Note this patch alone is not sufficient for port F enabling,
it's just the first step.
v2: Fix size of dvo_ports found by Ander.
v3: Adding missing cases from intel_bios.c for Port_F
v4: Adding other missing cases and fix the commit message.
v5: Rebase on top of display headers rework.
v6 (from Paulo): improve commit message, bikeshed bit definitions.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-2-paulo.r.zanoni@intel.com
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://anongit.freedesktop.org/drm/drm-intel into drm-next
[airlied: fix conflict in intel_dsi.c]
drm-intel-next-2017-12-01:
- Init clock gate fix (Ville)
- Execlists event handling corrections (Chris, Michel)
- Improvements on GPU Cache invalidation and context switch (Chris)
- More perf OA changes (Lionel)
- More selftests improvements and fixes (Chris, Matthew)
- Clean-up on modules parameters (Chris)
- Clean-up around old ringbuffer submission and hw semaphore on old platforms (Chris)
- More Cannonlake stabilization effort (David, James)
- Display planes clean-up and improvements (Ville)
- New PMU interface for perf queries... (Tvrtko)
- ... and other subsequent PMU changes and fixes (Tvrtko, Chris)
- Remove success dmesg noise from rotation (Chris)
- New DMC for Kabylake (Anusha)
- Fixes around atomic commits (Daniel)
- GuC updates and fixes (Sagar, Michal, Chris)
- Couple gmbus/i2c fixes (Ville)
- Use exponential backoff for all our wait_for() (Chris)
- Fixes for i915/fbdev (Chris)
- Backlight fixes (Arnd)
- Updates on shrinker (Chris)
- Make Hotplug enable more robuts (Chris)
- Disable huge pages (TPH) on lack of a needed workaround (Joonas)
- New GuC images for SKL, KBL, BXT (Sagar)
- Add HW Workaround for Geminilake performance (Valtteri)
- Fixes for PPS timings (Imre)
- More IPS fixes (Maarten)
- Many fixes for Display Port on gen2-gen4 (Ville)
- Retry GPU reset making the recover from hang more robust (Chris)
* tag 'drm-intel-next-2017-12-01' of git://anongit.freedesktop.org/drm/drm-intel: (101 commits)
drm/i915: Update DRIVER_DATE to 20171201
drm/i915/cnl: Mask previous DDI - PLL mapping
drm/i915: Remove unsafe i915.enable_rc6
drm/i915: Sleep and retry a GPU reset if at first we don't succeed
drm/i915: Interlaced DP output doesn't work on VLV/CHV
drm/i915: Pass crtc state to intel_pipe_{enable,disable}()
drm/i915: Wait for pipe to start on i830 as well
drm/i915: Fix vblank timestamp/frame counter jumps on gen2
drm/i915: Fix deadlock in i830_disable_pipe()
drm/i915: Fix has_audio readout for DDI A
drm/i915: Don't add the "force audio" property to DP connectors that don't support audio
drm/i915: Disable DP audio for g4x
drm/i915/selftests: Wake the device before executing requests on the GPU
drm/i915: Set fake_vma.size as well as fake_vma.node.size for capture
drm/i915: Tidy up signed/unsigned comparison
drm/i915: Enable IPS with only sprite plane visible too, v4.
drm/i915: Make ips_enabled a property depending on whether IPS is enabled, v3.
drm/i915: Avoid PPS HW/SW state mismatch due to rounding
drm/i915: Skip switch-to-kernel-context on suspend when wedged
drm/i915/glk: Apply WaProgramL3SqcReg1DefaultForPerf for GLK too
...
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Reject interlaced modes on VLV/CHV DP outputs. This simply does
not work correctly in the hardware. We do get some output, but
it's quite corrupted.
The available documentation fails to mention this fact. I
contacted some hardware people who eventually managed to locate
the relevant HSD for VLV, which was resolved by declaring
interlaced DP output as not supported. The HSD was never cloned
for CHV even though it inherited most of the hardware and
thus has the same problems with interlaced DP output.
Cc: Dennis Vshivkov <awesome.walrus+bugzilla@gmail.com>
Reported-by: Dennis Vshivkov <awesome.walrus+bugzilla@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103922
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129180847.30613-1-ville.syrjala@linux.intel.com
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|