| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
| |
Simple cloning rules compared to server:
(a) single crtc
(b) > 1 connector active
(c) check command line mode
(d) try and find 1024x768 DMT mode if no command line.
(e) fail to clone
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.
v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.
v3: add config lock take inside polling, add intel/nouveau poll init/fini calls
v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.
glisse: discard drm_helper_hpd_irq_event
v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Recently I've studied my system dmesg and seen this:
<lots of stuff before>
1 [ 0.478416] ACPI: Battery Slot [C1B4] (battery present)
2 [ 0.478648] ACPI: Battery Slot [C1B3] (battery absent)
3 [ 0.906678] [drm] initialized overlay support
4 [ 1.762304] Console: switching to colour frame buffer device 128x48
5 [ 1.765211] fb0: inteldrmfb frame buffer device
6 [ 1.765242] registered panic notifier
7 [ 1.765272] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
8 [ 1.765372] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
<lots of stuff after>
and it was not evident who registered that panic notifier on line 6.
I'd bought it as some low-level stuff needed by kernel itself, but the
time was inappropriate -- too late for such things.
So I had to study sources to see it was drm who was registering
switch-to-fb on panic.
Let's avoid possible confusion and mark this message as going from drm
subsystem.
(I'm a bit unsure whether to use '[drm]:' or 'drm:' -- the rest of the
kernel just uses 'topic:', and even in drm_fb_helper.c we use 'fb%d:'
without [] brackets. Either way is ok with me.)
Signed-off-by: Kirill Smelkov <kirr@landau.phys.spbu.ru>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* drm-fbdev-cleanup:
drm/fb: remove drm_fb_helper_setcolreg
drm/kms/fb: use slow work mechanism for normal hotplug also.
drm/kms/fb: add polling support for when nothing is connected.
drm/kms/fb: provide a 1024x768 fbcon if no outputs found.
drm/kms/fb: separate fbdev connector list from core drm connectors
drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
drm/fb: fix fbdev object model + cleanup properly.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/nouveau/nouveau_drv.h
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch is against the drm-fbdevfix1 branch. It removes the
drm_fb_helper_setcolreg function. The reason is that fb_setcolreg is only
used in the case where fb_setcmap is called and no fb_ops->fb_setcmap is
used. In the drm case we always need a fb_setcmap hook to handle multiple
crtcs so we don't need a fb_setcolreg hook. Please apply.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
a) slow work is always used now for any fbcon hotplug, as its not
a fast task and is more suited to being ran under slow work.
b) attempt to not do any fbdev changes when X is running as we'll
just mess it up. This hooks set_par to hopefully do the changes
once X hands control to fbdev.
This also adds the nouveau/intel hotplug support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When we are running in a headless environment we have no idea what
output the user might plug in later, we only have hotplug detect
from the digital outputs. So if we detect no connected outputs at
initialisation, start a slow work operation to poll every 5 seconds
for an output.
this is only hooked up for radeon so far, on hw where we have full
hotplug detection there is no need for this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
If we get no outputs setup provide a 1024x768 fbcon, with
this + radeon hotplug stuff I can plug a monitor in after startup
and get to see stuff.
Last thing is to add some sort of timer for non-hpd outputs like
VGA etc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This breaks the connection between the core drm connector list
and the fbdev connector usage, and allows them to become disjoint
in the future. It also removes the untype void* that was in the
connector struct to support this.
All connectors are added to the fbdev now but this could be
changed in the future.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This move to using the list of crtcs in the fb helper and cleans up the
whole picking code, now we store the crtc/connectors we want directly
into the modeset and we use the modeset directly to set the mode.
Fixes from James Simmons and Ben Skeggs.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The fbdev layer in the kms code should act like a consumer of the kms services and avoid having relying on information being store in the kms core structures in order for it to work.
This patch
a) removes the info pointer/psuedo palette from the core drm_framebuffer structure and moves it to the fbdev helper layer, it also removes the core drm keeping a list of kernel kms fbdevs.
b) migrated all the fb helper functions out of the crtc helper file into the fb helper file.
c) pushed the fb probing/hotplug control into the driver
d) makes the surface sizes into a structure for ease of passing
This changes the intel/radeon/nouveau drivers to use the new helper.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |\ \
| |/ |
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fix build error when CONFIG_MAGIC_SYSRQ is not enabled:
drivers/gpu/drm/drm_fb_helper.c:915: error: 'sysrq_drm_fb_helper_restore_op' undeclared (first use in this function)
drivers/gpu/drm/drm_fb_helper.c:929: error: 'sysrq_drm_fb_helper_restore_op' undeclared (first use in this function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
| |
|
|
|
|
|
| |
Signed-off-by: Pavel Roskin <proski@gnu.org>
[clemens@ladisch.de: merged into drm_fb_helper]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Kernel has simple_strtol() which would be used as atoi().
This is quite the same fix as in 2cb96f86628d6e97fcbda5fe4d8d74876239834c
("fbdev: drop custom atoi from drivers/video/modedb.c") because code in
drivers/gpu/drm/drm_fb_helper.c is based on drivers/video/modedb.c.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
commit 731b5a15a3b1474a41c2ca29b4c32b0f21bc852e
Author: James Simmons <jsimmons@infradead.org>
Date: Thu Oct 29 20:39:07 2009 +0000
drm/kms: properly handle fbdev blanking
uses DRM_MODE_DPMS_ON for FB_BLANK_NORMAL, but DRM_MODE_DPMS_ON
is actually for turning output on instead of blank.
This makes fb blank broken on my T61, it put LVDS on but leave
pipe disabled which made screen totally white or caused some
'burning' effect.
[airlied: James objects to this but at this point in 2.6.33,
I can't see a patch that will fix this properly like he wants coming
in time and otherwise this is a regression - proper fix for 2.6.34
hopefully.]
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
|
|
| |
If userspace (plymouth in this case) asks for a deeper depth,
refuse it as well due to lack of resizing.
This fixes an issue since < 32MB cards went to 8bpp and plymouth
crashes on startup.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
| |
This always evaluates to true.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |\
| |
| |
| |
| |
| |
| |
| | |
Bring all core drm changes into 2.6.32 tree and resolve
the conflict that occurs.
Conflicts:
drivers/gpu/drm/drm_fb_helper.c
|
| | |
| |
| |
| |
| |
| | |
crtc may be undefined at this point.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
Without an allocated colormap, FBIOGETCMAP fails. This would make
programs restore an all-black colormap ("links -g") or fail to work
altogether ("mplayer -vo fbdev2").
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When the framebuffer driver does not publish detailed timing information
for the current video mode, the correct value for the pixclock field is
zero, not -1.
Since pixclock is actually unsigned, the value -1 would be interpreted
as 4294967295 picoseconds (i.e., about 4 milliseconds) by
register_framebuffer() and userspace programs.
This patch allows X.org's fbdev driver to work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
I examined several fbdev drivers and foudn the blanking code in
drm_fb_helper to be wrong. This patch fixes the fbdev blanking to behave
like other fbdev drivers.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
This sets the fbcon to use TRUECOLOR by default, it then
only modifies the pseudo palette for fbcon, and only touches
the real palette when in 8-bit pseudo color mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When the framebuffer driver does not publish detailed timing information
for the current video mode, the correct value for the pixclock field is
zero, not -1.
Since pixclock is actually unsigned, the value -1 would be interpreted
as 4294967295 picoseconds (i.e., about 4 milliseconds) by
register_framebuffer() and userspace programs.
This patch allows X.org's fbdev driver to work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| | |
I believe this is a typo.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |/
|
|
|
|
|
|
| |
This sets the fbcon to use TRUECOLOR by default, it then
only modifies the pseudo palette for fbcon, and only touches
the real palette when in 8-bit pseudo color mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
The previous patches had some unwanted side effects, I've fixed
the lack of 32bpp working, and fixed up 16bpp so it should also work.
this also adds the interface to allow the driver to set a preferred
console depth so for example low memory rn50 can set it to 8bpp.
It also catches 24bpp on cards that can't do it and forces 32bpp.
Tested on r100/r600/i945.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
| |
This adds support for the setcmap api and fixes the 8bpp
support at least on radeon hardware. It adds a new load_lut
hook which can be called once the color map is setup.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Compiling DRM throws the following warning if MAGIC_SYSRQ is disabled:
drivers/gpu/drm/drm_fb_helper.c:101: warning: 'sysrq_drm_fb_helper_restore_op' defined but not used
Fix: place sysrq_drm_fb_helper_restore_op and associated
definitions inside #ifdef CONFIG_MAGIC_SYSRQ.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
| |
|
|
|
|
|
| |
This initialises the fb helper with the connector helper,
so that the fb cmdline code works for intel as well.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
| |
If drivers don't init the fb helper on the connector, the cmdline
code won't work, but it shouldn't crash either.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
[note this requires an fb patch posted to linux-fbdev-devel already]
This uses the normal video= command line option to control the kms
output setup at boot time. It is used to override the autodetection
done by kms.
video= normally takes a framebuffer as the first parameter, in kms
it will take a connector name, DVI-I-1, or LVDS-1 etc. If no output
connector is specified the mode string will apply to all connectors.
The mode specification used will match down the probed modes, and if
no mode is found it will add a CVT mode that matches.
video=1024x768 - all connectors match a 1024x768 mode or add a CVT on
video=VGA-1:1024x768, VGA-1 connector gets mode only.
The same strings as used in current fb modedb.c are used, except I've
added three more letters, e, D, d, e = enable, D = enable Digital,
d = disable, which allow a connector to be forced into a certain state.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
The drm_fb_helper shouldn't mess with CRTCs that aren't enabled or in
its initial config. Ideally it shouldn't even include CRTCs in its
initial config if they're not in use, but my old fix for that no longer
works. At any rate, this fixes a real bug I was seeing where after a
console blank, both pipes would come back on, even though only one had
been enabled before that. Since the other pipe had a bogus config,
this led to some screen corruption.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
| |
Allow the KMS module to work properly, and also rename
it to KMS_HELPER so its clearer what its for.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
| |
Set accel to none, we really don't want anyone thinking
fb is an accel interface.
Pass pitch not depth to function for intel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
|
Initially I always meant this code to be shared, but things
ran away from me before I got to it.
This refactors the i915 and radeon kms fbdev interaction layers
out into generic helpers + driver specific pieces.
It moves all the panic/sysrq enhancements to the core file,
and stores a linked list of kernel fbs. This could possibly be
improved to only store the fb which has fbcon on it for panics
etc.
radeon retains some specific codes used for a big endian
workaround.
changes:
fix oops in v1
fix freeing path for crtc_info
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
