summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/imx28-sps1.dts
Commit message (Collapse)AuthorAgeFilesLines
* ARM: i.MX28: dts: rename usbphy pin namesMichael Grzeschik2014-02-091-1/+1
| | | | | | | | The pins have nothing todo with the phy layer. We better rename them, so it gets clear they are routed to the ehci core not to any phy. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* ARM: dts: imx: use generic node name for fixed regulatorShawn Guo2014-02-091-1/+4
| | | | | | | | The device tree specification recommends that generic name should be used for nodes. So instead of naming those fixed regulator nodes arbitrarily, let's use the generic name 'regulator@num' for those nodes. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* ARM: dts: mxs: modify mx23/mx28 dts files to use padconfig definesLothar Waßmann2013-09-261-3/+3
| | | | | | | | Convert mx23/mx28 dts files to use the padconfig defintions from mxs-pinfunc.h. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* ARM: dts: mxs: modify mx23/mx28 dts files to use pinctrl headersLothar Waßmann2013-09-261-4/+4
| | | | | | | | | | | | | | | | | | Convert mx23/mx28 dts filed to use the pinctrl header files. NOTE: During automatic conversion of these files to use the pinconfig definitions an inconsistency has been found in: arch/arm/boot/dts/imx28-apx4devkit.dts According to the comment the function for pad SSP2_SS0 should have been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131 represents: MX28_PAD_SSP2_SS0__AUART3_TX I used the later (though probably wrong) definition because that's what is actually being used in the DTB. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* ARM: mxs: Slow down the I2C clock speedMarek Vasut2013-04-031-1/+0
| | | | | | | | | | | | | Slow down the I2C clock speed on M28 and SPS1 as it turns out the I2C block in i.MX28 can not operate stable enough with the bus running at 400kHz. Note that the driver used by Freescale runs the bus at 250kHz when 400kHz speed is selected, but the mainline Linux kernel runs the bus at actual 400kHz and that's where it is occasionally unstable. Play safe and run the bus at 100kHz. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* ARM: mxs: Add SchulerControl SPS1 DTS fileMarek Vasut2012-11-201-0/+169
Add DTS file for this custom board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
OpenPOWER on IntegriCloud