1 files changed, 31 insertions, 13 deletions

diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index 0e8fd135a57d..fcb587f825cc 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -28,8 +28,10 @@
 #include <mach/hardware.h>
 #include <mach/setup.h>
 #include <mach/devices.h>
+#include <mach/irqs.h>
 
 #include "pins-db8500.h"
+#include "board-mop500.h"
 
 static pin_cfg_t mop500_pins[] = {
 	/* SSP0 */
@@ -55,19 +57,13 @@ static void ab4500_spi_cs_control(u32 command)
 }
 
 struct pl022_config_chip ab4500_chip_info = {
-	.lbm = LOOPBACK_DISABLED,
 	.com_mode = INTERRUPT_TRANSFER,
 	.iface = SSP_INTERFACE_MOTOROLA_SPI,
 	/* we can act as master only */
 	.hierarchy = SSP_MASTER,
 	.slave_tx_disable = 0,
-	.endian_rx = SSP_RX_MSB,
-	.endian_tx = SSP_TX_MSB,
-	.data_size = SSP_DATA_BITS_24,
 	.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
 	.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
-	.clk_phase = SSP_CLK_SECOND_EDGE,
-	.clk_pol = SSP_CLK_POL_IDLE_HIGH,
 	.cs_control = ab4500_spi_cs_control,
 };
 
@@ -75,15 +71,33 @@ static struct ab8500_platform_data ab8500_platdata = {
 	.irq_base	= MOP500_AB8500_IRQ_BASE,
 };
 
-static struct spi_board_info u8500_spi_devices[] = {
+static struct resource ab8500_resources[] = {
+	[0] = {
+		.start = IRQ_AB8500,
+		.end = IRQ_AB8500,
+		.flags = IORESOURCE_IRQ
+	}
+};
+
+struct platform_device ab8500_device = {
+	.name = "ab8500-i2c",
+	.id = 0,
+	.dev = {
+		.platform_data = &ab8500_platdata,
+	},
+	.num_resources = 1,
+	.resource = ab8500_resources,
+};
+
+static struct spi_board_info ab8500_spi_devices[] = {
 	{
-		.modalias = "ab8500",
+		.modalias = "ab8500-spi",
 		.controller_data = &ab4500_chip_info,
 		.platform_data = &ab8500_platdata,
 		.max_speed_hz = 12000000,
 		.bus_num = 0,
 		.chip_select = 0,
-		.mode = SPI_MODE_0,
+		.mode = SPI_MODE_3,
 		.irq = IRQ_DB8500_AB8500,
 	},
 };
@@ -163,14 +177,18 @@ static void __init u8500_init_machine(void)
 
 	platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
 
-	spi_register_board_info(u8500_spi_devices,
-			ARRAY_SIZE(u8500_spi_devices));
+	mop500_sdi_init();
+
+	/* If HW is early drop (ED) or V1.0 then use SPI to access AB8500 */
+	if (cpu_is_u8500ed() || cpu_is_u8500v10())
+		spi_register_board_info(ab8500_spi_devices,
+			ARRAY_SIZE(ab8500_spi_devices));
+	else /* If HW is v.1.1 or later use I2C to access AB8500 */
+		platform_device_register(&ab8500_device);
 }
 
 MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
 	/* Maintainer: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> */
-	.phys_io	= U8500_UART2_BASE,
-	.io_pg_offst	= (IO_ADDRESS(U8500_UART2_BASE) >> 18) & 0xfffc,
 	.boot_params	= 0x100,
 	.map_io		= u8500_map_io,
 	.init_irq	= ux500_init_irq,