diff options
Diffstat (limited to 'arch/arm/boot/dts/ste-href-tvk1281618.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 52 |
1 files changed, 44 insertions, 8 deletions
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi index 0e1c96943d47..b7b4211c5353 100644 --- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi +++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi @@ -66,7 +66,7 @@ keypad,num-columns = <8>; keypad,num-rows = <8>; linux,no-autorepeat; - linux,wakeup; + wakeup-source; linux,keymap = <0x0301006b 0x04010066 0x06040072 @@ -104,13 +104,40 @@ <19 IRQ_TYPE_EDGE_RISING>; }; lsm303dlh@1e { - /* Magnetometer */ + /* + * This magnetometer is packaged with + * the accelerometer, and has a DRDY line, + * however it is not connected on this + * board so it can not generate interrupts. + */ compatible = "st,lsm303dlh-magn"; reg = <0x1e>; vdd-supply = <&ab8500_ldo_aux1_reg>; vddio-supply = <&db8500_vsmps2_reg>; + }; + lis331dl@1c { + /* Accelerometer */ + compatible = "st,lis331dl-accel"; + st,drdy-int-pin = <1>; + reg = <0x1c>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&accel_tvk_mode>; + interrupt-parent = <&gpio2>; + interrupts = <18 IRQ_TYPE_EDGE_RISING>, + <19 IRQ_TYPE_EDGE_RISING>; + }; + ak8974@0f { + /* Magnetometer */ + compatible = "asahi-kasei,ak8974"; + reg = <0x0f>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; pinctrl-names = "default"; - pinctrl-0 = <&magneto_tvk_mode>; + pinctrl-0 = <&gyro_magn_tvk_mode>; + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; }; l3g4200d@68 { /* Gyroscope */ @@ -119,6 +146,10 @@ reg = <0x68>; vdd-supply = <&ab8500_ldo_aux1_reg>; vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&gyro_magn_tvk_mode>; + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; }; lsp001wm@5c { /* Barometer/pressure sensor */ @@ -159,17 +190,22 @@ /* Accelerometer interrupt lines 1 & 2 */ tvk_cfg { pins = "GPIO82_C1", "GPIO83_D3"; - ste,config = <&gpio_in_pu>; + ste,config = <&gpio_in_pd>; }; }; }; - magnetometer { - magneto_tvk_mode: magneto_tvk { - /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */ + gyroscope { + /* + * These lines are shared between Gyroscope l3g400dh + * and AK8974 magnetometer. + */ + gyro_magn_tvk_mode: gyro_magn_tvk { + /* GPIO 31 used for INT pull down the line */ tvk_cfg1 { pins = "GPIO31_V3"; - ste,config = <&gpio_in_pu>; + ste,config = <&gpio_in_pd>; }; + /* GPIO 32 used for DRDY, pull this down */ tvk_cfg2 { pins = "GPIO32_V2"; ste,config = <&gpio_in_pd>; |
