diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/feature-removal-schedule.txt | 24 | ||||
| -rw-r--r-- | Documentation/keys.txt | 39 | ||||
| -rw-r--r-- | Documentation/kmemleak.txt | 31 | ||||
| -rw-r--r-- | Documentation/s390/s390dbf.txt | 7 | ||||
| -rw-r--r-- | Documentation/sound/alsa/ALSA-Configuration.txt | 30 | ||||
| -rw-r--r-- | Documentation/sound/alsa/HD-Audio-Models.txt | 33 | ||||
| -rw-r--r-- | Documentation/sound/alsa/HD-Audio.txt | 64 | ||||
| -rw-r--r-- | Documentation/sysctl/kernel.txt | 16 |
8 files changed, 234 insertions, 10 deletions
diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 09e031c55887..f0690bbbd73c 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -468,3 +468,27 @@ Why: cpu_policy_rwsem has a new cleaner definition making it local to cpufreq core and contained inside cpufreq.c. Other dependent drivers should not use it in order to safely avoid lockdep issues. Who: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> + +---------------------------- + +What: sound-slot/service-* module aliases and related clutters in + sound/sound_core.c +When: August 2010 +Why: OSS sound_core grabs all legacy minors (0-255) of SOUND_MAJOR + (14) and requests modules using custom sound-slot/service-* + module aliases. The only benefit of doing this is allowing + use of custom module aliases which might as well be considered + a bug at this point. This preemptive claiming prevents + alternative OSS implementations. + + Till the feature is removed, the kernel will be requesting + both sound-slot/service-* and the standard char-major-* module + aliases and allow turning off the pre-claiming selectively via + CONFIG_SOUND_OSS_CORE_PRECLAIM and soundcore.preclaim_oss + kernel parameter. + + After the transition phase is complete, both the custom module + aliases and switches to disable it will go away. This removal + will also allow making ALSA OSS emulation independent of + sound_core. The dependency will be broken then too. +Who: Tejun Heo <tj@kernel.org> diff --git a/Documentation/keys.txt b/Documentation/keys.txt index b56aacc1fff8..e4dbbdb1bd96 100644 --- a/Documentation/keys.txt +++ b/Documentation/keys.txt @@ -26,7 +26,7 @@ This document has the following sections: - Notes on accessing payload contents - Defining a key type - Request-key callback service - - Key access filesystem + - Garbage collection ============ @@ -113,6 +113,9 @@ Each key has a number of attributes: (*) Dead. The key's type was unregistered, and so the key is now useless. +Keys in the last three states are subject to garbage collection. See the +section on "Garbage collection". + ==================== KEY SERVICE OVERVIEW @@ -754,6 +757,26 @@ The keyctl syscall functions are: successful. + (*) Install the calling process's session keyring on its parent. + + long keyctl(KEYCTL_SESSION_TO_PARENT); + + This functions attempts to install the calling process's session keyring + on to the calling process's parent, replacing the parent's current session + keyring. + + The calling process must have the same ownership as its parent, the + keyring must have the same ownership as the calling process, the calling + process must have LINK permission on the keyring and the active LSM module + mustn't deny permission, otherwise error EPERM will be returned. + + Error ENOMEM will be returned if there was insufficient memory to complete + the operation, otherwise 0 will be returned to indicate success. + + The keyring will be replaced next time the parent process leaves the + kernel and resumes executing userspace. + + =============== KERNEL SERVICES =============== @@ -1231,3 +1254,17 @@ by executing: In this case, the program isn't required to actually attach the key to a ring; the rings are provided for reference. + + +================== +GARBAGE COLLECTION +================== + +Dead keys (for which the type has been removed) will be automatically unlinked +from those keyrings that point to them and deleted as soon as possible by a +background garbage collector. + +Similarly, revoked and expired keys will be garbage collected, but only after a +certain amount of time has passed. This time is set as a number of seconds in: + + /proc/sys/kernel/keys/gc_delay diff --git a/Documentation/kmemleak.txt b/Documentation/kmemleak.txt index 89068030b01b..34f6638aa5ac 100644 --- a/Documentation/kmemleak.txt +++ b/Documentation/kmemleak.txt @@ -27,6 +27,13 @@ To trigger an intermediate memory scan: # echo scan > /sys/kernel/debug/kmemleak +To clear the list of all current possible memory leaks: + + # echo clear > /sys/kernel/debug/kmemleak + +New leaks will then come up upon reading /sys/kernel/debug/kmemleak +again. + Note that the orphan objects are listed in the order they were allocated and one object at the beginning of the list may cause other subsequent objects to be reported as orphan. @@ -42,6 +49,9 @@ Memory scanning parameters can be modified at run-time by writing to the scan=<secs> - set the automatic memory scanning period in seconds (default 600, 0 to stop the automatic scanning) scan - trigger a memory scan + clear - clear list of current memory leak suspects, done by + marking all current reported unreferenced objects grey + dump=<addr> - dump information about the object found at <addr> Kmemleak can also be disabled at boot-time by passing "kmemleak=off" on the kernel command line. @@ -86,6 +96,27 @@ avoid this, kmemleak can also store the number of values pointing to an address inside the block address range that need to be found so that the block is not considered a leak. One example is __vmalloc(). +Testing specific sections with kmemleak +--------------------------------------- + +Upon initial bootup your /sys/kernel/debug/kmemleak output page may be +quite extensive. This can also be the case if you have very buggy code +when doing development. To work around these situations you can use the +'clear' command to clear all reported unreferenced objects from the +/sys/kernel/debug/kmemleak output. By issuing a 'scan' after a 'clear' +you can find new unreferenced objects; this should help with testing +specific sections of code. + +To test a critical section on demand with a clean kmemleak do: + + # echo clear > /sys/kernel/debug/kmemleak + ... test your kernel or modules ... + # echo scan > /sys/kernel/debug/kmemleak + +Then as usual to get your report with: + + # cat /sys/kernel/debug/kmemleak + Kmemleak API ------------ diff --git a/Documentation/s390/s390dbf.txt b/Documentation/s390/s390dbf.txt index 2d10053dd97e..ae66f9b90a25 100644 --- a/Documentation/s390/s390dbf.txt +++ b/Documentation/s390/s390dbf.txt @@ -495,6 +495,13 @@ and for each vararg a long value. So e.g. for a debug entry with a format string plus two varargs one would need to allocate a (3 * sizeof(long)) byte data area in the debug_register() function. +IMPORTANT: Using "%s" in sprintf event functions is dangerous. You can only +use "%s" in the sprintf event functions, if the memory for the passed string is +available as long as the debug feature exists. The reason behind this is that +due to performance considerations only a pointer to the string is stored in +the debug feature. If you log a string that is freed afterwards, you will get +an OOPS when inspecting the debug feature, because then the debug feature will +access the already freed memory. NOTE: If using the sprintf view do NOT use other event/exception functions than the sprintf-event and -exception functions. diff --git a/Documentation/sound/alsa/ALSA-Configuration.txt b/Documentation/sound/alsa/ALSA-Configuration.txt index 4252697a95d6..1c8eb4518ce0 100644 --- a/Documentation/sound/alsa/ALSA-Configuration.txt +++ b/Documentation/sound/alsa/ALSA-Configuration.txt @@ -60,6 +60,12 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. slots - Reserve the slot index for the given driver. This option takes multiple strings. See "Module Autoloading Support" section for details. + debug - Specifies the debug message level + (0 = disable debug prints, 1 = normal debug messages, + 2 = verbose debug messages) + This option appears only when CONFIG_SND_DEBUG=y. + This option can be dynamically changed via sysfs + /sys/modules/snd/parameters/debug file. Module snd-pcm-oss ------------------ @@ -513,6 +519,26 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. or input, but you may use this module for any application which requires a sound card (like RealPlayer). + pcm_devs - Number of PCM devices assigned to each card + (default = 1, up to 4) + pcm_substreams - Number of PCM substreams assigned to each PCM + (default = 8, up to 16) + hrtimer - Use hrtimer (=1, default) or system timer (=0) + fake_buffer - Fake buffer allocations (default = 1) + + When multiple PCM devices are created, snd-dummy gives different + behavior to each PCM device: + 0 = interleaved with mmap support + 1 = non-interleaved with mmap support + 2 = interleaved without mmap + 3 = non-interleaved without mmap + + As default, snd-dummy drivers doesn't allocate the real buffers + but either ignores read/write or mmap a single dummy page to all + buffer pages, in order to save the resouces. If your apps need + the read/ written buffer data to be consistent, pass fake_buffer=0 + option. + The power-management is supported. Module snd-echo3g @@ -768,6 +794,10 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. bdl_pos_adj - Specifies the DMA IRQ timing delay in samples. Passing -1 will make the driver to choose the appropriate value based on the controller chip. + patch - Specifies the early "patch" files to modify the HD-audio + setup before initializing the codecs. This option is + available only when CONFIG_SND_HDA_PATCH_LOADER=y is set. + See HD-Audio.txt for details. [Single (global) options] single_cmd - Use single immediate commands to communicate with diff --git a/Documentation/sound/alsa/HD-Audio-Models.txt b/Documentation/sound/alsa/HD-Audio-Models.txt index 939a3dd58148..97eebd63bedc 100644 --- a/Documentation/sound/alsa/HD-Audio-Models.txt +++ b/Documentation/sound/alsa/HD-Audio-Models.txt @@ -114,8 +114,8 @@ ALC662/663/272 samsung-nc10 Samsung NC10 mini notebook auto auto-config reading BIOS (default) -ALC882/885 -========== +ALC882/883/885/888/889 +====================== 3stack-dig 3-jack with SPDIF I/O 6stack-dig 6-jack digital with SPDIF I/O arima Arima W820Di1 @@ -127,12 +127,8 @@ ALC882/885 mbp3 Macbook Pro rev3 imac24 iMac 24'' with jack detection w2jc ASUS W2JC - auto auto-config reading BIOS (default) - -ALC883/888 -========== - 3stack-dig 3-jack with SPDIF I/O - 6stack-dig 6-jack digital with SPDIF I/O + 3stack-2ch-dig 3-jack with SPDIF I/O (ALC883) + alc883-6stack-dig 6-jack digital with SPDIF I/O (ALC883) 3stack-6ch 3-jack 6-channel 3stack-6ch-dig 3-jack 6-channel with SPDIF I/O 6stack-dig-demo 6-jack digital for Intel demo board @@ -140,6 +136,7 @@ ALC883/888 acer-aspire Acer Aspire 9810 acer-aspire-4930g Acer Aspire 4930G acer-aspire-6530g Acer Aspire 6530G + acer-aspire-7730g Acer Aspire 7730G acer-aspire-8930g Acer Aspire 8930G medion Medion Laptops medion-md2 Medion MD2 @@ -155,10 +152,13 @@ ALC883/888 3stack-hp HP machines with 3stack (Lucknow, Samba boards) 6stack-dell Dell machines with 6stack (Inspiron 530) mitac Mitac 8252D + clevo-m540r Clevo M540R (6ch + digital) clevo-m720 Clevo M720 laptop series fujitsu-pi2515 Fujitsu AMILO Pi2515 fujitsu-xa3530 Fujitsu AMILO XA3530 3stack-6ch-intel Intel DG33* boards + intel-alc889a Intel IbexPeak with ALC889A + intel-x58 Intel DX58 with ALC889 asus-p5q ASUS P5Q-EM boards mb31 MacBook 3,1 sony-vaio-tt Sony VAIO TT @@ -229,7 +229,7 @@ AD1984 ====== basic default configuration thinkpad Lenovo Thinkpad T61/X61 - dell Dell T3400 + dell_desktop Dell T3400 AD1986A ======= @@ -258,6 +258,7 @@ Conexant 5045 laptop-micsense Laptop with Mic sense (old model fujitsu) laptop-hpmicsense Laptop with HP and Mic senses benq Benq R55E + laptop-hp530 HP 530 laptop test for testing/debugging purpose, almost all controls can be adjusted. Appearing only when compiled with $CONFIG_SND_DEBUG=y @@ -278,9 +279,16 @@ Conexant 5051 hp-dv6736 HP dv6736 lenovo-x200 Lenovo X200 laptop +Conexant 5066 +============= + laptop Basic Laptop config (default) + dell-laptop Dell laptops + olpc-xo-1_5 OLPC XO 1.5 + STAC9200 ======== ref Reference board + oqo OQO Model 2 dell-d21 Dell (unknown) dell-d22 Dell (unknown) dell-d23 Dell (unknown) @@ -368,10 +376,12 @@ STAC92HD73* =========== ref Reference board no-jd BIOS setup but without jack-detection + intel Intel DG45* mobos dell-m6-amic Dell desktops/laptops with analog mics dell-m6-dmic Dell desktops/laptops with digital mics dell-m6 Dell desktops/laptops with both type of mics dell-eq Dell desktops/laptops + alienware Alienware M17x auto BIOS setup (default) STAC92HD83* @@ -385,3 +395,8 @@ STAC9872 ======== vaio VAIO laptop without SPDIF auto BIOS setup (default) + +Cirrus Logic CS4206/4207 +======================== + mbp55 MacBook Pro 5,5 + auto BIOS setup (default) diff --git a/Documentation/sound/alsa/HD-Audio.txt b/Documentation/sound/alsa/HD-Audio.txt index 71ac995b1915..7b8a5f947d1d 100644 --- a/Documentation/sound/alsa/HD-Audio.txt +++ b/Documentation/sound/alsa/HD-Audio.txt @@ -139,6 +139,10 @@ The driver checks PCI SSID and looks through the static configuration table until any matching entry is found. If you have a new machine, you may see a message like below: ------------------------------------------------------------------------ + hda_codec: ALC880: BIOS auto-probing. +------------------------------------------------------------------------ +Meanwhile, in the earlier versions, you would see a message like: +------------------------------------------------------------------------ hda_codec: Unknown model for ALC880, trying auto-probe from BIOS... ------------------------------------------------------------------------ Even if you see such a message, DON'T PANIC. Take a deep breath and @@ -403,6 +407,66 @@ re-configure based on that state, run like below: ------------------------------------------------------------------------ +Early Patching +~~~~~~~~~~~~~~ +When CONFIG_SND_HDA_PATCH_LOADER=y is set, you can pass a "patch" as a +firmware file for modifying the HD-audio setup before initializing the +codec. This can work basically like the reconfiguration via sysfs in +the above, but it does it before the first codec configuration. + +A patch file is a plain text file which looks like below: + +------------------------------------------------------------------------ + [codec] + 0x12345678 0xabcd1234 2 + + [model] + auto + + [pincfg] + 0x12 0x411111f0 + + [verb] + 0x20 0x500 0x03 + 0x20 0x400 0xff + + [hint] + hp_detect = yes +------------------------------------------------------------------------ + +The file needs to have a line `[codec]`. The next line should contain +three numbers indicating the codec vendor-id (0x12345678 in the +example), the codec subsystem-id (0xabcd1234) and the address (2) of +the codec. The rest patch entries are applied to this specified codec +until another codec entry is given. + +The `[model]` line allows to change the model name of the each codec. +In the example above, it will be changed to model=auto. +Note that this overrides the module option. + +After the `[pincfg]` line, the contents are parsed as the initial +default pin-configurations just like `user_pin_configs` sysfs above. +The values can be shown in user_pin_configs sysfs file, too. + +Similarly, the lines after `[verb]` are parsed as `init_verbs` +sysfs entries, and the lines after `[hint]` are parsed as `hints` +sysfs entries, respectively. + +The hd-audio driver reads the file via request_firmware(). Thus, +a patch file has to be located on the appropriate firmware path, +typically, /lib/firmware. For example, when you pass the option +`patch=hda-init.fw`, the file /lib/firmware/hda-init-fw must be +present. + +The patch module option is specific to each card instance, and you +need to give one file name for each instance, separated by commas. +For example, if you have two cards, one for an on-board analog and one +for an HDMI video board, you may pass patch option like below: +------------------------------------------------------------------------ + options snd-hda-intel patch=on-board-patch,hdmi-patch +------------------------------------------------------------------------ + + Power-Saving ~~~~~~~~~~~~ The power-saving is a kind of auto-suspend of the device. When the diff --git a/Documentation/sysctl/kernel.txt b/Documentation/sysctl/kernel.txt index 322a00bb99d9..2dbff53369d0 100644 --- a/Documentation/sysctl/kernel.txt +++ b/Documentation/sysctl/kernel.txt @@ -19,6 +19,7 @@ Currently, these files might (depending on your configuration) show up in /proc/sys/kernel: - acpi_video_flags - acct +- callhome [ S390 only ] - auto_msgmni - core_pattern - core_uses_pid @@ -91,6 +92,21 @@ valid for 30 seconds. ============================================================== +callhome: + +Controls the kernel's callhome behavior in case of a kernel panic. + +The s390 hardware allows an operating system to send a notification +to a service organization (callhome) in case of an operating system panic. + +When the value in this file is 0 (which is the default behavior) +nothing happens in case of a kernel panic. If this value is set to "1" +the complete kernel oops message is send to the IBM customer service +organization in case the mainframe the Linux operating system is running +on has a service contract with IBM. + +============================================================== + core_pattern: core_pattern is used to specify a core dumpfile pattern name. |
