Merge branch 'spear/pcie-support-v10' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/linux into next/drivers

Merge "ARM: SPEAr13xx PCIe updates for v3.17" from Viresh Kumar:

This is another attempt to merge SPEAr PCIe updates after olof
pointed out *enough* issues with initial PULL request:

https://lkml.org/lkml/2014/7/9/641

Last version was sent here: http://patchwork.ozlabs.org/patch/368479/
and all the nits pointed out by Kishon & Bjorn are fixed in this pull
request.

Apart from ARM specific changes, this updates drivers/{pci|phy}. Bjorn
advised to get complete series via arm-soc tree earlier:

http://www.spinics.net/lists/linux-pci/msg30271.html

* 'spear/pcie-support-v10' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/linux:
  ARM: SPEAr13xx: Update defconfigs
  ARM: SPEAr13xx: Add pcie and miphy DT nodes
  ARM: SPEAr13xx: Add bindings and dt node for misc block
  ARM: SPEAr13xx: Fix static mapping table
  phy: Add drivers for PCIe and SATA phy on SPEAr13xx
  PCI: spear: Add PCIe driver for ST Microelectronics SPEAr13xx

Signed-off-by: Olof Johansson <olof@lixom.net>

21 files changed, 1211 insertions, 133 deletions

diff --git a/Documentation/devicetree/bindings/arm/spear-misc.txt b/Documentation/devicetree/bindings/arm/spear-misc.txt
new file mode 100644
index 000000000000..cf649827ffcd
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/spear-misc.txt
@@ -0,0 +1,9 @@
+SPEAr Misc configuration
+===========================
+SPEAr SOCs have some miscellaneous registers which are used to configure
+few properties of different peripheral controllers.
+
+misc node required properties:
+
+- compatible Should be	"st,spear1340-misc", "syscon".
+- reg: Address range of misc space upto 8K
diff --git a/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt b/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt
new file mode 100644
index 000000000000..49ea76da7718
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt
@@ -0,0 +1,14 @@
+SPEAr13XX PCIe DT detail:
+================================
+
+SPEAr13XX uses synopsis designware PCIe controller and ST MiPHY as phy
+controller.
+
+Required properties:
+- compatible : should be "st,spear1340-pcie", "snps,dw-pcie".
+- phys		    : phandle to phy node associated with pcie controller
+- phy-names	    : must be "pcie-phy"
+- All other definitions as per generic PCI bindings
+
+ Optional properties:
+- st,pcie-is-gen1 indicates that forced gen1 initialization is needed.
diff --git a/Documentation/devicetree/bindings/phy/st-spear-miphy.txt b/Documentation/devicetree/bindings/phy/st-spear-miphy.txt
new file mode 100644
index 000000000000..2a6bfdcc09b3
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/st-spear-miphy.txt
@@ -0,0 +1,15 @@
+ST SPEAr miphy DT details
+=========================
+
+ST Microelectronics SPEAr miphy is a phy controller supporting PCIe and SATA.
+
+Required properties:
+- compatible : should be "st,spear1310-miphy" or "st,spear1340-miphy"
+- reg : offset and length of the PHY register set.
+- misc: phandle for the syscon node to access misc registers
+- #phy-cells : from the generic PHY bindings, must be 1.
+	- cell[1]: 0 if phy used for SATA, 1 for PCIe.
+
+Optional properties:
+- phy-id: Instance id of the phy. Only required when there are multiple phys
+  present on a implementation.
diff --git a/MAINTAINERS b/MAINTAINERS
index 702ca10a5a6c..766948ed64db 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -6820,6 +6820,12 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/pci/host-generic-pci.txt
 F:	drivers/pci/host/pci-host-generic.c
 
+PCIE DRIVER FOR ST SPEAR13XX
+M:	Mohit Kumar <mohit.kumar@st.com>
+L:	linux-pci@vger.kernel.org
+S:	Maintained
+F:	drivers/pci/host/*spear*
+
 PCMCIA SUBSYSTEM
 P:	Linux PCMCIA Team
 L:	linux-pcmcia@lists.infradead.org
diff --git a/arch/arm/boot/dts/spear1310-evb.dts b/arch/arm/boot/dts/spear1310-evb.dts
index b56a801e42a2..d42c84b1df8d 100644
--- a/arch/arm/boot/dts/spear1310-evb.dts
+++ b/arch/arm/boot/dts/spear1310-evb.dts
@@ -106,6 +106,10 @@
 			status = "okay";
 		};
 
+		miphy@eb800000 {
+			status = "okay";
+		};
+
 		cf@b2800000 {
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/spear1310.dtsi b/arch/arm/boot/dts/spear1310.dtsi
index 122ae94076c8..fa5f2bb5f106 100644
--- a/arch/arm/boot/dts/spear1310.dtsi
+++ b/arch/arm/boot/dts/spear1310.dtsi
@@ -29,24 +29,111 @@
 			#gpio-cells = <2>;
 		};
 
-		ahci@b1000000 {
+		miphy0: miphy@eb800000 {
+			compatible = "st,spear1310-miphy";
+			reg = <0xeb800000 0x4000>;
+			misc = <&misc>;
+			phy-id = <0>;
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		miphy1: miphy@eb804000 {
+			compatible = "st,spear1310-miphy";
+			reg = <0xeb804000 0x4000>;
+			misc = <&misc>;
+			phy-id = <1>;
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		miphy2: miphy@eb808000 {
+			compatible = "st,spear1310-miphy";
+			reg = <0xeb808000 0x4000>;
+			misc = <&misc>;
+			phy-id = <2>;
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		ahci0: ahci@b1000000 {
 			compatible = "snps,spear-ahci";
 			reg = <0xb1000000 0x10000>;
 			interrupts = <0 68 0x4>;
+			phys = <&miphy0 0>;
+			phy-names = "sata-phy";
 			status = "disabled";
 		};
 
-		ahci@b1800000 {
+		ahci1: ahci@b1800000 {
 			compatible = "snps,spear-ahci";
 			reg = <0xb1800000 0x10000>;
 			interrupts = <0 69 0x4>;
+			phys = <&miphy1 0>;
+			phy-names = "sata-phy";
 			status = "disabled";
 		};
 
-		ahci@b4000000 {
+		ahci2: ahci@b4000000 {
 			compatible = "snps,spear-ahci";
 			reg = <0xb4000000 0x10000>;
 			interrupts = <0 70 0x4>;
+			phys = <&miphy2 0>;
+			phy-names = "sata-phy";
+			status = "disabled";
+		};
+
+		pcie0: pcie@b1000000 {
+			compatible = "st,spear1340-pcie", "snps,dw-pcie";
+			reg = <0xb1000000 0x4000>;
+			interrupts = <0 68 0x4>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0x0 0 &gic 0 68 0x4>;
+			num-lanes = <1>;
+			phys = <&miphy0 1>;
+			phy-names = "pcie-phy";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x00000800 0 0x80000000 0x80000000 0 0x00020000   /* configuration space */
+				0x81000000 0 0	 0x80020000 0 0x00010000   /* downstream I/O */
+				0x82000000 0 0x80030000 0xc0030000 0 0x0ffd0000>; /* non-prefetchable memory */
+			status = "disabled";
+		};
+
+		pcie1: pcie@b1800000 {
+			compatible = "st,spear1340-pcie", "snps,dw-pcie";
+			reg = <0xb1800000 0x4000>;
+			interrupts = <0 69 0x4>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0x0 0 &gic 0 69 0x4>;
+			num-lanes = <1>;
+			phys = <&miphy1 1>;
+			phy-names = "pcie-phy";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x00000800 0 0x90000000 0x90000000 0 0x00020000   /* configuration space */
+				0x81000000 0 0  0x90020000 0 0x00010000   /* downstream I/O */
+				0x82000000 0 0x90030000 0x90030000 0 0x0ffd0000>; /* non-prefetchable memory */
+			status = "disabled";
+		};
+
+		pcie2: pcie@b4000000 {
+			compatible = "st,spear1340-pcie", "snps,dw-pcie";
+			reg = <0xb4000000 0x4000>;
+			interrupts = <0 70 0x4>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0x0 0 &gic 0 70 0x4>;
+			num-lanes = <1>;
+			phys = <&miphy2 1>;
+			phy-names = "pcie-phy";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x00000800 0 0xc0000000 0xc0000000 0 0x00020000   /* configuration space */
+				0x81000000 0 0	 0xc0020000 0 0x00010000   /* downstream I/O */
+				0x82000000 0 0xc0030000 0xc0030000 0 0x0ffd0000>; /* non-prefetchable memory */
 			status = "disabled";
 		};
 
diff --git a/arch/arm/boot/dts/spear1340-evb.dts b/arch/arm/boot/dts/spear1340-evb.dts
index d6c30ae0a8d7..b23e05ed1d60 100644
--- a/arch/arm/boot/dts/spear1340-evb.dts
+++ b/arch/arm/boot/dts/spear1340-evb.dts
@@ -122,6 +122,10 @@
 			status = "okay";
 		};
 
+		miphy@eb800000 {
+			status = "okay";
+		};
+
 		dma@ea800000 {
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/spear1340.dtsi b/arch/arm/boot/dts/spear1340.dtsi
index 54d128d35681..e71df0f2cb52 100644
--- a/arch/arm/boot/dts/spear1340.dtsi
+++ b/arch/arm/boot/dts/spear1340.dtsi
@@ -31,10 +31,38 @@
 			status = "disabled";
 		};
 
-		ahci@b1000000 {
+		miphy0: miphy@eb800000 {
+			compatible = "st,spear1340-miphy";
+			reg = <0xeb800000 0x4000>;
+			misc = <&misc>;
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		ahci0: ahci@b1000000 {
 			compatible = "snps,spear-ahci";
 			reg = <0xb1000000 0x10000>;
 			interrupts = <0 72 0x4>;
+			phys = <&miphy0 0>;
+			phy-names = "sata-phy";
+			status = "disabled";
+		};
+
+		pcie0: pcie@b1000000 {
+			compatible = "st,spear1340-pcie", "snps,dw-pcie";
+			reg = <0xb1000000 0x4000>;
+			interrupts = <0 68 0x4>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0x0 0 &gic 0 68 0x4>;
+			num-lanes = <1>;
+			phys = <&miphy0 1>;
+			phy-names = "pcie-phy";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x00000800 0 0x80000000 0x80000000 0 0x00020000   /* configuration space */
+				0x81000000 0 0	 0x80020000 0 0x00010000   /* downstream I/O */
+				0x82000000 0 0x80030000 0xc0030000 0 0x0ffd0000>; /* non-prefetchable memory */
 			status = "disabled";
 		};
 
diff --git a/arch/arm/boot/dts/spear13xx.dtsi b/arch/arm/boot/dts/spear13xx.dtsi
index 4382547df58a..a6eb5436d26d 100644
--- a/arch/arm/boot/dts/spear13xx.dtsi
+++ b/arch/arm/boot/dts/spear13xx.dtsi
@@ -83,8 +83,8 @@
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		ranges = <0x50000000 0x50000000 0x10000000
-			  0xb0000000 0xb0000000 0x10000000
-			  0xd0000000 0xd0000000 0x02000000
+			  0x80000000 0x80000000 0x20000000
+			  0xb0000000 0xb0000000 0x22000000
 			  0xd8000000 0xd8000000 0x01000000
 			  0xe0000000 0xe0000000 0x10000000>;
 
@@ -220,6 +220,11 @@
 				  0xd8000000 0xd8000000 0x01000000
 				  0xe0000000 0xe0000000 0x10000000>;
 
+			misc: syscon@e0700000 {
+				compatible = "st,spear1340-misc", "syscon";
+				reg = <0xe0700000 0x1000>;
+			};
+
 			gpio0: gpio@e0600000 {
 				compatible = "arm,pl061", "arm,primecell";
 				reg = <0xe0600000 0x1000>;
diff --git a/arch/arm/configs/spear13xx_defconfig b/arch/arm/configs/spear13xx_defconfig
index 82eaa552ed14..d271b263f35d 100644
--- a/arch/arm/configs/spear13xx_defconfig
+++ b/arch/arm/configs/spear13xx_defconfig
@@ -11,13 +11,24 @@ CONFIG_ARCH_SPEAR13XX=y
 CONFIG_MACH_SPEAR1310=y
 CONFIG_MACH_SPEAR1340=y
 # CONFIG_SWP_EMULATE is not set
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
+CONFIG_PCIE_SPEAR13XX=y
 CONFIG_SMP=y
 # CONFIG_SMP_ON_UP is not set
 # CONFIG_ARM_CPU_TOPOLOGY is not set
+CONFIG_AEABI=y
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
+CONFIG_VFP=y
 CONFIG_BINFMT_MISC=y
 CONFIG_NET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_NET_IPIP=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_MTD=y
 CONFIG_MTD_OF_PARTS=y
@@ -27,6 +38,7 @@ CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_FSMC=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_BLK_DEV_SD=y
 CONFIG_ATA=y
 # CONFIG_SATA_PMP is not set
 CONFIG_SATA_AHCI_PLATFORM=y
@@ -66,6 +78,7 @@ CONFIG_USB=y
 # CONFIG_USB_DEVICE_CLASS is not set
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_STORAGE=y
 CONFIG_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_SPEAR=y
@@ -79,11 +92,14 @@ CONFIG_EXT2_FS_SECURITY=y
 CONFIG_EXT3_FS=y
 CONFIG_EXT3_FS_SECURITY=y
 CONFIG_AUTOFS4_FS=m
+CONFIG_FUSE_FS=y
 CONFIG_MSDOS_FS=m
 CONFIG_VFAT_FS=m
 CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
 CONFIG_TMPFS=y
 CONFIG_JFFS2_FS=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
 CONFIG_NLS_DEFAULT="utf8"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=m
diff --git a/arch/arm/mach-spear/Kconfig b/arch/arm/mach-spear/Kconfig
index 90df2022276a..6fd4dc88160b 100644
--- a/arch/arm/mach-spear/Kconfig
+++ b/arch/arm/mach-spear/Kconfig
@@ -19,6 +19,8 @@ config ARCH_SPEAR13XX
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
 	select PINCTRL
+	select MFD_SYSCON
+	select MIGHT_HAVE_PCI
 	help
 	  Supports for ARM's SPEAR13XX family
 
@@ -27,12 +29,14 @@ if ARCH_SPEAR13XX
 config MACH_SPEAR1310
 	bool "SPEAr1310 Machine support with Device Tree"
 	select PINCTRL_SPEAR1310
+	select PHY_ST_SPEAR1310_MIPHY
 	help
 	  Supports ST SPEAr1310 machine configured via the device-tree
 
 config MACH_SPEAR1340
 	bool "SPEAr1340 Machine support with Device Tree"
 	select PINCTRL_SPEAR1340
+	select PHY_ST_SPEAR1340_MIPHY
 	help
 	  Supports ST SPEAr1340 machine configured via the device-tree
 
diff --git a/arch/arm/mach-spear/include/mach/spear.h b/arch/arm/mach-spear/include/mach/spear.h
index 5cdc53d9b653..f2d6a0176575 100644
--- a/arch/arm/mach-spear/include/mach/spear.h
+++ b/arch/arm/mach-spear/include/mach/spear.h
@@ -52,10 +52,10 @@
 #ifdef CONFIG_ARCH_SPEAR13XX
 
 #define PERIP_GRP2_BASE				UL(0xB3000000)
-#define VA_PERIP_GRP2_BASE			IOMEM(0xFE000000)
+#define VA_PERIP_GRP2_BASE			IOMEM(0xF9000000)
 #define MCIF_SDHCI_BASE				UL(0xB3000000)
 #define SYSRAM0_BASE				UL(0xB3800000)
-#define VA_SYSRAM0_BASE				IOMEM(0xFE800000)
+#define VA_SYSRAM0_BASE				IOMEM(0xF9800000)
 #define SYS_LOCATION				(VA_SYSRAM0_BASE + 0x600)
 
 #define PERIP_GRP1_BASE				UL(0xE0000000)
diff --git a/arch/arm/mach-spear/spear1340.c b/arch/arm/mach-spear/spear1340.c
index 7b6bff7154e1..3f3c0f124bd3 100644
--- a/arch/arm/mach-spear/spear1340.c
+++ b/arch/arm/mach-spear/spear1340.c
@@ -13,136 +13,13 @@
 
 #define pr_fmt(fmt) "SPEAr1340: " fmt
 
-#include <linux/ahci_platform.h>
-#include <linux/amba/serial.h>
-#include <linux/delay.h>
 #include <linux/of_platform.h>
 #include <asm/mach/arch.h>
 #include "generic.h"
-#include <mach/spear.h>
-
-/* FIXME: Move SATA PHY code into a standalone driver */
-
-/* Base addresses */
-#define SPEAR1340_SATA_BASE			UL(0xB1000000)
-
-/* Power Management Registers */
-#define SPEAR1340_PCM_CFG			(VA_MISC_BASE + 0x100)
-#define SPEAR1340_PCM_WKUP_CFG			(VA_MISC_BASE + 0x104)
-#define SPEAR1340_SWITCH_CTR			(VA_MISC_BASE + 0x108)
-
-#define SPEAR1340_PERIP1_SW_RST			(VA_MISC_BASE + 0x318)
-#define SPEAR1340_PERIP2_SW_RST			(VA_MISC_BASE + 0x31C)
-#define SPEAR1340_PERIP3_SW_RST			(VA_MISC_BASE + 0x320)
-
-/* PCIE - SATA configuration registers */
-#define SPEAR1340_PCIE_SATA_CFG			(VA_MISC_BASE + 0x424)
-	/* PCIE CFG MASks */
-	#define SPEAR1340_PCIE_CFG_DEVICE_PRESENT	(1 << 11)
-	#define SPEAR1340_PCIE_CFG_POWERUP_RESET	(1 << 10)
-	#define SPEAR1340_PCIE_CFG_CORE_CLK_EN		(1 << 9)
-	#define SPEAR1340_PCIE_CFG_AUX_CLK_EN		(1 << 8)
-	#define SPEAR1340_SATA_CFG_TX_CLK_EN		(1 << 4)
-	#define SPEAR1340_SATA_CFG_RX_CLK_EN		(1 << 3)
-	#define SPEAR1340_SATA_CFG_POWERUP_RESET	(1 << 2)
-	#define SPEAR1340_SATA_CFG_PM_CLK_EN		(1 << 1)
-	#define SPEAR1340_PCIE_SATA_SEL_PCIE		(0)
-	#define SPEAR1340_PCIE_SATA_SEL_SATA		(1)
-	#define SPEAR1340_SATA_PCIE_CFG_MASK		0xF1F
-	#define SPEAR1340_PCIE_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_PCIE | \
-			SPEAR1340_PCIE_CFG_AUX_CLK_EN | \
-			SPEAR1340_PCIE_CFG_CORE_CLK_EN | \
-			SPEAR1340_PCIE_CFG_POWERUP_RESET | \
-			SPEAR1340_PCIE_CFG_DEVICE_PRESENT)
-	#define SPEAR1340_SATA_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_SATA | \
-			SPEAR1340_SATA_CFG_PM_CLK_EN | \
-			SPEAR1340_SATA_CFG_POWERUP_RESET | \
-			SPEAR1340_SATA_CFG_RX_CLK_EN | \
-			SPEAR1340_SATA_CFG_TX_CLK_EN)
-
-#define SPEAR1340_PCIE_MIPHY_CFG		(VA_MISC_BASE + 0x428)
-	#define SPEAR1340_MIPHY_OSC_BYPASS_EXT		(1 << 31)
-	#define SPEAR1340_MIPHY_CLK_REF_DIV2		(1 << 27)
-	#define SPEAR1340_MIPHY_CLK_REF_DIV4		(2 << 27)
-	#define SPEAR1340_MIPHY_CLK_REF_DIV8		(3 << 27)
-	#define SPEAR1340_MIPHY_PLL_RATIO_TOP(x)	(x << 0)
-	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA \
-			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
-			SPEAR1340_MIPHY_CLK_REF_DIV2 | \
-			SPEAR1340_MIPHY_PLL_RATIO_TOP(60))
-	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \
-			(SPEAR1340_MIPHY_PLL_RATIO_TOP(120))
-	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE \
-			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
-			SPEAR1340_MIPHY_PLL_RATIO_TOP(25))
-
-/* SATA device registration */
-static int sata_miphy_init(struct device *dev, void __iomem *addr)
-{
-	writel(SPEAR1340_SATA_CFG_VAL, SPEAR1340_PCIE_SATA_CFG);
-	writel(SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK,
-			SPEAR1340_PCIE_MIPHY_CFG);
-	/* Switch on sata power domain */
-	writel((readl(SPEAR1340_PCM_CFG) | (0x800)), SPEAR1340_PCM_CFG);
-	msleep(20);
-	/* Disable PCIE SATA Controller reset */
-	writel((readl(SPEAR1340_PERIP1_SW_RST) & (~0x1000)),
-			SPEAR1340_PERIP1_SW_RST);
-	msleep(20);
-
-	return 0;
-}
-
-void sata_miphy_exit(struct device *dev)
-{
-	writel(0, SPEAR1340_PCIE_SATA_CFG);
-	writel(0, SPEAR1340_PCIE_MIPHY_CFG);
-
-	/* Enable PCIE SATA Controller reset */
-	writel((readl(SPEAR1340_PERIP1_SW_RST) | (0x1000)),
-			SPEAR1340_PERIP1_SW_RST);
-	msleep(20);
-	/* Switch off sata power domain */
-	writel((readl(SPEAR1340_PCM_CFG) & (~0x800)), SPEAR1340_PCM_CFG);
-	msleep(20);
-}
-
-int sata_suspend(struct device *dev)
-{
-	if (dev->power.power_state.event == PM_EVENT_FREEZE)
-		return 0;
-
-	sata_miphy_exit(dev);
-
-	return 0;
-}
-
-int sata_resume(struct device *dev)
-{
-	if (dev->power.power_state.event == PM_EVENT_THAW)
-		return 0;
-
-	return sata_miphy_init(dev, NULL);
-}
-
-static struct ahci_platform_data sata_pdata = {
-	.init = sata_miphy_init,
-	.exit = sata_miphy_exit,
-	.suspend = sata_suspend,
-	.resume = sata_resume,
-};
-
-/* Add SPEAr1340 auxdata to pass platform data */
-static struct of_dev_auxdata spear1340_auxdata_lookup[] __initdata = {
-	OF_DEV_AUXDATA("snps,spear-ahci", SPEAR1340_SATA_BASE, NULL,
-			&sata_pdata),
-	{}
-};
 
 static void __init spear1340_dt_init(void)
 {
-	of_platform_populate(NULL, of_default_bus_match_table,
-			spear1340_auxdata_lookup, NULL);
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 	platform_device_register_simple("spear-cpufreq", -1, NULL, 0);
 }
 
diff --git a/arch/arm/mach-spear/spear13xx.c b/arch/arm/mach-spear/spear13xx.c
index c9897ea38980..53a761482a7c 100644
--- a/arch/arm/mach-spear/spear13xx.c
+++ b/arch/arm/mach-spear/spear13xx.c
@@ -52,7 +52,7 @@ void __init spear13xx_l2x0_init(void)
 /*
  * Following will create 16MB static virtual/physical mappings
  * PHYSICAL		VIRTUAL
- * 0xB3000000		0xFE000000
+ * 0xB3000000		0xF9000000
  * 0xE0000000		0xFD000000
  * 0xEC000000		0xFC000000
  * 0xED000000		0xFB000000
diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
index 21df477be0c8..2d8a4d05d78f 100644
--- a/drivers/pci/host/Kconfig
+++ b/drivers/pci/host/Kconfig
@@ -46,4 +46,12 @@ config PCI_HOST_GENERIC
 	  Say Y here if you want to support a simple generic PCI host
 	  controller, such as the one emulated by kvmtool.
 
+config PCIE_SPEAR13XX
+	tristate "STMicroelectronics SPEAr PCIe controller"
+	depends on ARCH_SPEAR13XX
+	select PCIEPORTBUS
+	select PCIE_DW
+	help
+	  Say Y here if you want PCIe support on SPEAr13XX SoCs.
+
 endmenu
diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile
index 611ba4b48c94..0daec7941aba 100644
--- a/drivers/pci/host/Makefile
+++ b/drivers/pci/host/Makefile
@@ -6,3 +6,4 @@ obj-$(CONFIG_PCI_TEGRA) += pci-tegra.o
 obj-$(CONFIG_PCI_RCAR_GEN2) += pci-rcar-gen2.o
 obj-$(CONFIG_PCI_RCAR_GEN2_PCIE) += pcie-rcar.o
 obj-$(CONFIG_PCI_HOST_GENERIC) += pci-host-generic.o
+obj-$(CONFIG_PCIE_SPEAR13XX) += pcie-spear13xx.o
diff --git a/drivers/pci/host/pcie-spear13xx.c b/drivers/pci/host/pcie-spear13xx.c
new file mode 100644
index 000000000000..99738e432596
--- /dev/null
+++ b/drivers/pci/host/pcie-spear13xx.c
@@ -0,0 +1,405 @@
+/*
+ * PCIe host controller driver for ST Microelectronics SPEAr13xx SoCs
+ *
+ * SPEAr13xx PCIe Glue Layer Source Code
+ *
+ * Copyright (C) 2010-2014 ST Microelectronics
+ * Pratyush Anand <pratyush.anand@st.com>
+ * Mohit Kumar <mohit.kumar@st.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pci.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/resource.h>
+
+#include "pcie-designware.h"
+
+struct spear13xx_pcie {
+	void __iomem		*app_base;
+	struct phy		*phy;
+	struct clk		*clk;
+	struct pcie_port	pp;
+	bool			is_gen1;
+};
+
+struct pcie_app_reg {
+	u32	app_ctrl_0;		/* cr0 */
+	u32	app_ctrl_1;		/* cr1 */
+	u32	app_status_0;		/* cr2 */
+	u32	app_status_1;		/* cr3 */
+	u32	msg_status;		/* cr4 */
+	u32	msg_payload;		/* cr5 */
+	u32	int_sts;		/* cr6 */
+	u32	int_clr;		/* cr7 */
+	u32	int_mask;		/* cr8 */
+	u32	mst_bmisc;		/* cr9 */
+	u32	phy_ctrl;		/* cr10 */
+	u32	phy_status;		/* cr11 */
+	u32	cxpl_debug_info_0;	/* cr12 */
+	u32	cxpl_debug_info_1;	/* cr13 */
+	u32	ven_msg_ctrl_0;		/* cr14 */
+	u32	ven_msg_ctrl_1;		/* cr15 */
+	u32	ven_msg_data_0;		/* cr16 */
+	u32	ven_msg_data_1;		/* cr17 */
+	u32	ven_msi_0;		/* cr18 */
+	u32	ven_msi_1;		/* cr19 */
+	u32	mst_rmisc;		/* cr20 */
+};
+
+/* CR0 ID */
+#define RX_LANE_FLIP_EN_ID			0
+#define TX_LANE_FLIP_EN_ID			1
+#define SYS_AUX_PWR_DET_ID			2
+#define APP_LTSSM_ENABLE_ID			3
+#define SYS_ATTEN_BUTTON_PRESSED_ID		4
+#define SYS_MRL_SENSOR_STATE_ID			5
+#define SYS_PWR_FAULT_DET_ID			6
+#define SYS_MRL_SENSOR_CHGED_ID			7
+#define SYS_PRE_DET_CHGED_ID			8
+#define SYS_CMD_CPLED_INT_ID			9
+#define APP_INIT_RST_0_ID			11
+#define APP_REQ_ENTR_L1_ID			12
+#define APP_READY_ENTR_L23_ID			13
+#define APP_REQ_EXIT_L1_ID			14
+#define DEVICE_TYPE_EP				(0 << 25)
+#define DEVICE_TYPE_LEP				(1 << 25)
+#define DEVICE_TYPE_RC				(4 << 25)
+#define SYS_INT_ID				29
+#define MISCTRL_EN_ID				30
+#define REG_TRANSLATION_ENABLE			31
+
+/* CR1 ID */
+#define APPS_PM_XMT_TURNOFF_ID			2
+#define APPS_PM_XMT_PME_ID			5
+
+/* CR3 ID */
+#define XMLH_LTSSM_STATE_DETECT_QUIET		0x00
+#define XMLH_LTSSM_STATE_DETECT_ACT		0x01
+#define XMLH_LTSSM_STATE_POLL_ACTIVE		0x02
+#define XMLH_LTSSM_STATE_POLL_COMPLIANCE	0x03
+#define XMLH_LTSSM_STATE_POLL_CONFIG		0x04
+#define XMLH_LTSSM_STATE_PRE_DETECT_QUIET	0x05
+#define XMLH_LTSSM_STATE_DETECT_WAIT		0x06
+#define XMLH_LTSSM_STATE_CFG_LINKWD_START	0x07
+#define XMLH_LTSSM_STATE_CFG_LINKWD_ACEPT	0x08
+#define XMLH_LTSSM_STATE_CFG_LANENUM_WAIT	0x09
+#define XMLH_LTSSM_STATE_CFG_LANENUM_ACEPT	0x0A
+#define XMLH_LTSSM_STATE_CFG_COMPLETE		0x0B
+#define XMLH_LTSSM_STATE_CFG_IDLE		0x0C
+#define XMLH_LTSSM_STATE_RCVRY_LOCK		0x0D
+#define XMLH_LTSSM_STATE_RCVRY_SPEED		0x0E
+#define XMLH_LTSSM_STATE_RCVRY_RCVRCFG		0x0F
+#define XMLH_LTSSM_STATE_RCVRY_IDLE		0x10
+#define XMLH_LTSSM_STATE_L0			0x11
+#define XMLH_LTSSM_STATE_L0S			0x12
+#define XMLH_LTSSM_STATE_L123_SEND_EIDLE	0x13
+#define XMLH_LTSSM_STATE_L1_IDLE		0x14
+#define XMLH_LTSSM_STATE_L2_IDLE		0x15
+#define XMLH_LTSSM_STATE_L2_WAKE		0x16
+#define XMLH_LTSSM_STATE_DISABLED_ENTRY		0x17
+#define XMLH_LTSSM_STATE_DISABLED_IDLE		0x18
+#define XMLH_LTSSM_STATE_DISABLED		0x19
+#define XMLH_LTSSM_STATE_LPBK_ENTRY		0x1A
+#define XMLH_LTSSM_STATE_LPBK_ACTIVE		0x1B
+#define XMLH_LTSSM_STATE_LPBK_EXIT		0x1C
+#define XMLH_LTSSM_STATE_LPBK_EXIT_TIMEOUT	0x1D
+#define XMLH_LTSSM_STATE_HOT_RESET_ENTRY	0x1E
+#define XMLH_LTSSM_STATE_HOT_RESET		0x1F
+#define XMLH_LTSSM_STATE_MASK			0x3F
+#define XMLH_LINK_UP				(1 << 6)
+
+/* CR4 ID */
+#define CFG_MSI_EN_ID				18
+
+/* CR6 */
+#define INTA_CTRL_INT				(1 << 7)
+#define INTB_CTRL_INT				(1 << 8)
+#define INTC_CTRL_INT				(1 << 9)
+#define INTD_CTRL_INT				(1 << 10)
+#define MSI_CTRL_INT				(1 << 26)
+
+/* CR19 ID */
+#define VEN_MSI_REQ_ID				11
+#define VEN_MSI_FUN_NUM_ID			8
+#define VEN_MSI_TC_ID				5
+#define VEN_MSI_VECTOR_ID			0
+#define VEN_MSI_REQ_EN		((u32)0x1 << VEN_MSI_REQ_ID)
+#define VEN_MSI_FUN_NUM_MASK	((u32)0x7 << VEN_MSI_FUN_NUM_ID)
+#define VEN_MSI_TC_MASK		((u32)0x7 << VEN_MSI_TC_ID)
+#define VEN_MSI_VECTOR_MASK	((u32)0x1F << VEN_MSI_VECTOR_ID)
+
+#define EXP_CAP_ID_OFFSET			0x70
+
+#define to_spear13xx_pcie(x)	container_of(x, struct spear13xx_pcie, pp)
+
+static int spear13xx_pcie_establish_link(struct pcie_port *pp)
+{
+	u32 val;
+	int count = 0;
+	struct spear13xx_pcie *spear13xx_pcie = to_spear13xx_pcie(pp);
+	struct pcie_app_reg *app_reg = spear13xx_pcie->app_base;
+	u32 exp_cap_off = EXP_CAP_ID_OFFSET;
+
+	if (dw_pcie_link_up(pp)) {
+		dev_err(pp->dev, "link already up\n");
+		return 0;
+	}
+
+	dw_pcie_setup_rc(pp);
+
+	/*
+	 * this controller support only 128 bytes read size, however its
+	 * default value in capability register is 512 bytes. So force
+	 * it to 128 here.
+	 */
+	dw_pcie_cfg_read(pp->dbi_base, exp_cap_off + PCI_EXP_DEVCTL, 4, &val);
+	val &= ~PCI_EXP_DEVCTL_READRQ;
+	dw_pcie_cfg_write(pp->dbi_base, exp_cap_off + PCI_EXP_DEVCTL, 4, val);
+
+	dw_pcie_cfg_write(pp->dbi_base, PCI_VENDOR_ID, 2, 0x104A);
+	dw_pcie_cfg_write(pp->dbi_base, PCI_DEVICE_ID, 2, 0xCD80);
+
+	/*
+	 * if is_gen1 is set then handle it, so that some buggy card
+	 * also works
+	 */
+	if (spear13xx_pcie->is_gen1) {
+		dw_pcie_cfg_read(pp->dbi_base, exp_cap_off + PCI_EXP_LNKCAP, 4,
+				 &val);
+		if ((val & PCI_EXP_LNKCAP_SLS) != PCI_EXP_LNKCAP_SLS_2_5GB) {
+			val &= ~((u32)PCI_EXP_LNKCAP_SLS);
+			val |= PCI_EXP_LNKCAP_SLS_2_5GB;
+			dw_pcie_cfg_write(pp->dbi_base, exp_cap_off +
+					  PCI_EXP_LNKCAP, 4, val);
+		}
+
+		dw_pcie_cfg_read(pp->dbi_base, exp_cap_off + PCI_EXP_LNKCTL2, 4,
+				 &val);
+		if ((val & PCI_EXP_LNKCAP_SLS) != PCI_EXP_LNKCAP_SLS_2_5GB) {
+			val &= ~((u32)PCI_EXP_LNKCAP_SLS);
+			val |= PCI_EXP_LNKCAP_SLS_2_5GB;
+			dw_pcie_cfg_write(pp->dbi_base, exp_cap_off +
+					  PCI_EXP_LNKCTL2, 4, val);
+		}
+	}
+
+	/* enable ltssm */
+	writel(DEVICE_TYPE_RC | (1 << MISCTRL_EN_ID)
+			| (1 << APP_LTSSM_ENABLE_ID)
+			| ((u32)1 << REG_TRANSLATION_ENABLE),
+			&app_reg->app_ctrl_0);
+
+	/* check if the link is up or not */
+	while (!dw_pcie_link_up(pp)) {
+		mdelay(100);
+		count++;
+		if (count == 10) {
+			dev_err(pp->dev, "link Fail\n");
+			return -EINVAL;
+		}
+	}
+	dev_info(pp->dev, "link up\n");
+
+	return 0;
+}
+
+static irqreturn_t spear13xx_pcie_irq_handler(int irq, void *arg)
+{
+	struct pcie_port *pp = arg;
+	struct spear13xx_pcie *spear13xx_pcie = to_spear13xx_pcie(pp);
+	struct pcie_app_reg *app_reg = spear13xx_pcie->app_base;
+	unsigned int status;
+
+	status = readl(&app_reg->int_sts);
+
+	if (status & MSI_CTRL_INT) {
+		if (!IS_ENABLED(CONFIG_PCI_MSI))
+			BUG();
+		dw_handle_msi_irq(pp);
+	}
+
+	writel(status, &app_reg->int_clr);
+
+	return IRQ_HANDLED;
+}
+
+static void spear13xx_pcie_enable_interrupts(struct pcie_port *pp)
+{
+	struct spear13xx_pcie *spear13xx_pcie = to_spear13xx_pcie(pp);
+	struct pcie_app_reg *app_reg = spear13xx_pcie->app_base;
+
+	/* Enable MSI interrupt */
+	if (IS_ENABLED(CONFIG_PCI_MSI)) {
+		dw_pcie_msi_init(pp);
+		writel(readl(&app_reg->int_mask) |
+				MSI_CTRL_INT, &app_reg->int_mask);
+	}
+}
+
+static int spear13xx_pcie_link_up(struct pcie_port *pp)
+{
+	struct spear13xx_pcie *spear13xx_pcie = to_spear13xx_pcie(pp);
+	struct pcie_app_reg *app_reg = spear13xx_pcie->app_base;
+
+	if (readl(&app_reg->app_status_1) & XMLH_LINK_UP)
+		return 1;
+
+	return 0;
+}
+
+static void spear13xx_pcie_host_init(struct pcie_port *pp)
+{
+	spear13xx_pcie_establish_link(pp);
+	spear13xx_pcie_enable_interrupts(pp);
+}
+
+static struct pcie_host_ops spear13xx_pcie_host_ops = {
+	.link_up = spear13xx_pcie_link_up,
+	.host_init = spear13xx_pcie_host_init,
+};
+
+static int add_pcie_port(struct pcie_port *pp, struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	pp->irq = platform_get_irq(pdev, 0);
+	if (!pp->irq) {
+		dev_err(dev, "failed to get irq\n");
+		return -ENODEV;
+	}
+	ret = devm_request_irq(dev, pp->irq, spear13xx_pcie_irq_handler,
+			       IRQF_SHARED, "spear1340-pcie", pp);
+	if (ret) {
+		dev_err(dev, "failed to request irq %d\n", pp->irq);
+		return ret;
+	}
+
+	pp->root_bus_nr = -1;
+	pp->ops = &spear13xx_pcie_host_ops;
+
+	ret = dw_pcie_host_init(pp);
+	if (ret) {
+		dev_err(dev, "failed to initialize host\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int __init spear13xx_pcie_probe(struct platform_device *pdev)
+{
+	struct spear13xx_pcie *spear13xx_pcie;
+	struct pcie_port *pp;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = pdev->dev.of_node;
+	struct resource *dbi_base;
+	int ret;
+
+	spear13xx_pcie = devm_kzalloc(dev, sizeof(*spear13xx_pcie), GFP_KERNEL);
+	if (!spear13xx_pcie) {
+		dev_err(dev, "no memory for SPEAr13xx pcie\n");
+		return -ENOMEM;
+	}
+
+	spear13xx_pcie->phy = devm_phy_get(dev, "pcie-phy");
+	if (IS_ERR(spear13xx_pcie->phy)) {
+		ret = PTR_ERR(spear13xx_pcie->phy);
+		if (ret == -EPROBE_DEFER)
+			dev_info(dev, "probe deferred\n");
+		else
+			dev_err(dev, "couldn't get pcie-phy\n");
+		return ret;
+	}
+
+	phy_init(spear13xx_pcie->phy);
+
+	spear13xx_pcie->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(spear13xx_pcie->clk)) {
+		dev_err(dev, "couldn't get clk for pcie\n");
+		return PTR_ERR(spear13xx_pcie->clk);
+	}
+	ret = clk_prepare_enable(spear13xx_pcie->clk);
+	if (ret) {
+		dev_err(dev, "couldn't enable clk for pcie\n");
+		return ret;
+	}
+
+	pp = &spear13xx_pcie->pp;
+
+	pp->dev = dev;
+
+	dbi_base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	pp->dbi_base = devm_ioremap_resource(dev, dbi_base);
+	if (IS_ERR(pp->dbi_base)) {
+		dev_err(dev, "couldn't remap dbi base %p\n", dbi_base);
+		ret = PTR_ERR(pp->dbi_base);
+		goto fail_clk;
+	}
+	spear13xx_pcie->app_base = pp->dbi_base + 0x2000;
+
+	if (of_property_read_bool(np, "st,pcie-is-gen1"))
+		spear13xx_pcie->is_gen1 = true;
+
+	ret = add_pcie_port(pp, pdev);
+	if (ret < 0)
+		goto fail_clk;
+
+	platform_set_drvdata(pdev, spear13xx_pcie);
+	return 0;
+
+fail_clk:
+	clk_disable_unprepare(spear13xx_pcie->clk);
+
+	return ret;
+}
+
+static int __exit spear13xx_pcie_remove(struct platform_device *pdev)
+{
+	struct spear13xx_pcie *spear13xx_pcie = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(spear13xx_pcie->clk);
+
+	phy_exit(spear13xx_pcie->phy);
+
+	return 0;
+}
+
+static const struct of_device_id spear13xx_pcie_of_match[] = {
+	{ .compatible = "st,spear1340-pcie", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, spear13xx_pcie_of_match);
+
+static struct platform_driver spear13xx_pcie_driver = {
+	.probe		= spear13xx_pcie_probe,
+	.remove		= spear13xx_pcie_remove,
+	.driver = {
+		.name	= "spear-pcie",
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(spear13xx_pcie_of_match),
+	},
+};
+
+/* SPEAr13xx PCIe driver does not allow module unload */
+
+static int __init pcie_init(void)
+{
+	return platform_driver_register(&spear13xx_pcie_driver);
+}
+module_init(pcie_init);
+
+MODULE_DESCRIPTION("ST Microelectronics SPEAr13xx PCIe host controller driver");
+MODULE_AUTHOR("Pratyush Anand <pratyush.anand@st.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 16a2f067c242..e8f8a2d165d1 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -178,4 +178,16 @@ config PHY_XGENE
 	help
 	  This option enables support for APM X-Gene SoC multi-purpose PHY.
 
+config PHY_ST_SPEAR1310_MIPHY
+	tristate "ST SPEAR1310-MIPHY driver"
+	select GENERIC_PHY
+	help
+	  Support for ST SPEAr1310 MIPHY which can be used for PCIe and SATA.
+
+config PHY_ST_SPEAR1340_MIPHY
+	tristate "ST SPEAR1340-MIPHY driver"
+	select GENERIC_PHY
+	help
+	  Support for ST SPEAr1340 MIPHY which can be used for PCIe and SATA.
+
 endmenu
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index b4f1d5770601..d39609bb38de 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -20,3 +20,5 @@ phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4X12_USB2)	+= phy-exynos4x12-usb2.o
 phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2)	+= phy-exynos5250-usb2.o
 obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
 obj-$(CONFIG_PHY_XGENE)			+= phy-xgene.o
+obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
+obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o
diff --git a/drivers/phy/phy-spear1310-miphy.c b/drivers/phy/phy-spear1310-miphy.c
new file mode 100644
index 000000000000..c58c869d57e0
--- /dev/null
+++ b/drivers/phy/phy-spear1310-miphy.c
@@ -0,0 +1,274 @@
+/*
+ * ST SPEAr1310-miphy driver
+ *
+ * Copyright (C) 2014 ST Microelectronics
+ * Pratyush Anand <pratyush.anand@st.com>
+ * Mohit Kumar <mohit.kumar@st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+
+/* SPEAr1310 Registers */
+#define SPEAR1310_PCIE_SATA_CFG			0x3A4
+	#define SPEAR1310_PCIE_SATA2_SEL_PCIE		(0 << 31)
+	#define SPEAR1310_PCIE_SATA1_SEL_PCIE		(0 << 30)
+	#define SPEAR1310_PCIE_SATA0_SEL_PCIE		(0 << 29)
+	#define SPEAR1310_PCIE_SATA2_SEL_SATA		BIT(31)
+	#define SPEAR1310_PCIE_SATA1_SEL_SATA		BIT(30)
+	#define SPEAR1310_PCIE_SATA0_SEL_SATA		BIT(29)
+	#define SPEAR1310_SATA2_CFG_TX_CLK_EN		BIT(27)
+	#define SPEAR1310_SATA2_CFG_RX_CLK_EN		BIT(26)
+	#define SPEAR1310_SATA2_CFG_POWERUP_RESET	BIT(25)
+	#define SPEAR1310_SATA2_CFG_PM_CLK_EN		BIT(24)
+	#define SPEAR1310_SATA1_CFG_TX_CLK_EN		BIT(23)
+	#define SPEAR1310_SATA1_CFG_RX_CLK_EN		BIT(22)
+	#define SPEAR1310_SATA1_CFG_POWERUP_RESET	BIT(21)
+	#define SPEAR1310_SATA1_CFG_PM_CLK_EN		BIT(20)
+	#define SPEAR1310_SATA0_CFG_TX_CLK_EN		BIT(19)
+	#define SPEAR1310_SATA0_CFG_RX_CLK_EN		BIT(18)
+	#define SPEAR1310_SATA0_CFG_POWERUP_RESET	BIT(17)
+	#define SPEAR1310_SATA0_CFG_PM_CLK_EN		BIT(16)
+	#define SPEAR1310_PCIE2_CFG_DEVICE_PRESENT	BIT(11)
+	#define SPEAR1310_PCIE2_CFG_POWERUP_RESET	BIT(10)
+	#define SPEAR1310_PCIE2_CFG_CORE_CLK_EN		BIT(9)
+	#define SPEAR1310_PCIE2_CFG_AUX_CLK_EN		BIT(8)
+	#define SPEAR1310_PCIE1_CFG_DEVICE_PRESENT	BIT(7)
+	#define SPEAR1310_PCIE1_CFG_POWERUP_RESET	BIT(6)
+	#define SPEAR1310_PCIE1_CFG_CORE_CLK_EN		BIT(5)
+	#define SPEAR1310_PCIE1_CFG_AUX_CLK_EN		BIT(4)
+	#define SPEAR1310_PCIE0_CFG_DEVICE_PRESENT	BIT(3)
+	#define SPEAR1310_PCIE0_CFG_POWERUP_RESET	BIT(2)
+	#define SPEAR1310_PCIE0_CFG_CORE_CLK_EN		BIT(1)
+	#define SPEAR1310_PCIE0_CFG_AUX_CLK_EN		BIT(0)
+
+	#define SPEAR1310_PCIE_CFG_MASK(x) ((0xF << (x * 4)) | BIT((x + 29)))
+	#define SPEAR1310_SATA_CFG_MASK(x) ((0xF << (x * 4 + 16)) | \
+			BIT((x + 29)))
+	#define SPEAR1310_PCIE_CFG_VAL(x) \
+			(SPEAR1310_PCIE_SATA##x##_SEL_PCIE | \
+			SPEAR1310_PCIE##x##_CFG_AUX_CLK_EN | \
+			SPEAR1310_PCIE##x##_CFG_CORE_CLK_EN | \
+			SPEAR1310_PCIE##x##_CFG_POWERUP_RESET | \
+			SPEAR1310_PCIE##x##_CFG_DEVICE_PRESENT)
+	#define SPEAR1310_SATA_CFG_VAL(x) \
+			(SPEAR1310_PCIE_SATA##x##_SEL_SATA | \
+			SPEAR1310_SATA##x##_CFG_PM_CLK_EN | \
+			SPEAR1310_SATA##x##_CFG_POWERUP_RESET | \
+			SPEAR1310_SATA##x##_CFG_RX_CLK_EN | \
+			SPEAR1310_SATA##x##_CFG_TX_CLK_EN)
+
+#define SPEAR1310_PCIE_MIPHY_CFG_1		0x3A8
+	#define SPEAR1310_MIPHY_DUAL_OSC_BYPASS_EXT	BIT(31)
+	#define SPEAR1310_MIPHY_DUAL_CLK_REF_DIV2	BIT(28)
+	#define SPEAR1310_MIPHY_DUAL_PLL_RATIO_TOP(x)	(x << 16)
+	#define SPEAR1310_MIPHY_SINGLE_OSC_BYPASS_EXT	BIT(15)
+	#define SPEAR1310_MIPHY_SINGLE_CLK_REF_DIV2	BIT(12)
+	#define SPEAR1310_MIPHY_SINGLE_PLL_RATIO_TOP(x)	(x << 0)
+	#define SPEAR1310_PCIE_SATA_MIPHY_CFG_SATA_MASK (0xFFFF)
+	#define SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE_MASK (0xFFFF << 16)
+	#define SPEAR1310_PCIE_SATA_MIPHY_CFG_SATA \
+			(SPEAR1310_MIPHY_DUAL_OSC_BYPASS_EXT | \
+			SPEAR1310_MIPHY_DUAL_CLK_REF_DIV2 | \
+			SPEAR1310_MIPHY_DUAL_PLL_RATIO_TOP(60) | \
+			SPEAR1310_MIPHY_SINGLE_OSC_BYPASS_EXT | \
+			SPEAR1310_MIPHY_SINGLE_CLK_REF_DIV2 | \
+			SPEAR1310_MIPHY_SINGLE_PLL_RATIO_TOP(60))
+	#define SPEAR1310_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \
+			(SPEAR1310_MIPHY_SINGLE_PLL_RATIO_TOP(120))
+	#define SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE \
+			(SPEAR1310_MIPHY_DUAL_OSC_BYPASS_EXT | \
+			SPEAR1310_MIPHY_DUAL_PLL_RATIO_TOP(25) | \
+			SPEAR1310_MIPHY_SINGLE_OSC_BYPASS_EXT | \
+			SPEAR1310_MIPHY_SINGLE_PLL_RATIO_TOP(25))
+
+#define SPEAR1310_PCIE_MIPHY_CFG_2		0x3AC
+
+enum spear1310_miphy_mode {
+	SATA,
+	PCIE,
+};
+
+struct spear1310_miphy_priv {
+	/* instance id of this phy */
+	u32				id;
+	/* phy mode: 0 for SATA 1 for PCIe */
+	enum spear1310_miphy_mode	mode;
+	/* regmap for any soc specific misc registers */
+	struct regmap			*misc;
+	/* phy struct pointer */
+	struct phy			*phy;
+};
+
+static int spear1310_miphy_pcie_init(struct spear1310_miphy_priv *priv)
+{
+	u32 val;
+
+	regmap_update_bits(priv->misc, SPEAR1310_PCIE_MIPHY_CFG_1,
+			   SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE_MASK,
+			   SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE);
+
+	switch (priv->id) {
+	case 0:
+		val = SPEAR1310_PCIE_CFG_VAL(0);
+		break;
+	case 1:
+		val = SPEAR1310_PCIE_CFG_VAL(1);
+		break;
+	case 2:
+		val = SPEAR1310_PCIE_CFG_VAL(2);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	regmap_update_bits(priv->misc, SPEAR1310_PCIE_SATA_CFG,
+			   SPEAR1310_PCIE_CFG_MASK(priv->id), val);
+
+	return 0;
+}
+
+static int spear1310_miphy_pcie_exit(struct spear1310_miphy_priv *priv)
+{
+	regmap_update_bits(priv->misc, SPEAR1310_PCIE_SATA_CFG,
+			   SPEAR1310_PCIE_CFG_MASK(priv->id), 0);
+
+	regmap_update_bits(priv->misc, SPEAR1310_PCIE_MIPHY_CFG_1,
+			   SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE_MASK, 0);
+
+	return 0;
+}
+
+static int spear1310_miphy_init(struct phy *phy)
+{
+	struct spear1310_miphy_priv *priv = phy_get_drvdata(phy);
+	int ret = 0;
+
+	if (priv->mode == PCIE)
+		ret = spear1310_miphy_pcie_init(priv);
+
+	return ret;
+}
+
+static int spear1310_miphy_exit(struct phy *phy)
+{
+	struct spear1310_miphy_priv *priv = phy_get_drvdata(phy);
+	int ret = 0;
+
+	if (priv->mode == PCIE)
+		ret = spear1310_miphy_pcie_exit(priv);
+
+	return ret;
+}
+
+static const struct of_device_id spear1310_miphy_of_match[] = {
+	{ .compatible = "st,spear1310-miphy" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, spear1310_miphy_of_match);
+
+static struct phy_ops spear1310_miphy_ops = {
+	.init = spear1310_miphy_init,
+	.exit = spear1310_miphy_exit,
+	.owner = THIS_MODULE,
+};
+
+static struct phy *spear1310_miphy_xlate(struct device *dev,
+					 struct of_phandle_args *args)
+{
+	struct spear1310_miphy_priv *priv = dev_get_drvdata(dev);
+
+	if (args->args_count < 1) {
+		dev_err(dev, "DT did not pass correct no of args\n");
+		return NULL;
+	}
+
+	priv->mode = args->args[0];
+
+	if (priv->mode != SATA && priv->mode != PCIE) {
+		dev_err(dev, "DT did not pass correct phy mode\n");
+		return NULL;
+	}
+
+	return priv->phy;
+}
+
+static int spear1310_miphy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct spear1310_miphy_priv *priv;
+	struct phy_provider *phy_provider;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv) {
+		dev_err(dev, "can't alloc spear1310_miphy private date memory\n");
+		return -ENOMEM;
+	}
+
+	priv->misc =
+		syscon_regmap_lookup_by_phandle(dev->of_node, "misc");
+	if (IS_ERR(priv->misc)) {
+		dev_err(dev, "failed to find misc regmap\n");
+		return PTR_ERR(priv->misc);
+	}
+
+	if (of_property_read_u32(dev->of_node, "phy-id", &priv->id)) {
+		dev_err(dev, "failed to find phy id\n");
+		return -EINVAL;
+	}
+
+	priv->phy = devm_phy_create(dev, &spear1310_miphy_ops, NULL);
+	if (IS_ERR(priv->phy)) {
+		dev_err(dev, "failed to create SATA PCIe PHY\n");
+		return PTR_ERR(priv->phy);
+	}
+
+	dev_set_drvdata(dev, priv);
+	phy_set_drvdata(priv->phy, priv);
+
+	phy_provider =
+		devm_of_phy_provider_register(dev, spear1310_miphy_xlate);
+	if (IS_ERR(phy_provider)) {
+		dev_err(dev, "failed to register phy provider\n");
+		return PTR_ERR(phy_provider);
+	}
+
+	return 0;
+}
+
+static struct platform_driver spear1310_miphy_driver = {
+	.probe		= spear1310_miphy_probe,
+	.driver = {
+		.name = "spear1310-miphy",
+		.owner = THIS_MODULE,
+		.of_match_table = of_match_ptr(spear1310_miphy_of_match),
+	},
+};
+
+static int __init spear1310_miphy_phy_init(void)
+{
+	return platform_driver_register(&spear1310_miphy_driver);
+}
+module_init(spear1310_miphy_phy_init);
+
+static void __exit spear1310_miphy_phy_exit(void)
+{
+	platform_driver_unregister(&spear1310_miphy_driver);
+}
+module_exit(spear1310_miphy_phy_exit);
+
+MODULE_DESCRIPTION("ST SPEAR1310-MIPHY driver");
+MODULE_AUTHOR("Pratyush Anand <pratyush.anand@st.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/phy-spear1340-miphy.c b/drivers/phy/phy-spear1340-miphy.c
new file mode 100644
index 000000000000..8de98adf21c3
--- /dev/null
+++ b/drivers/phy/phy-spear1340-miphy.c
@@ -0,0 +1,307 @@
+/*
+ * ST spear1340-miphy driver
+ *
+ * Copyright (C) 2014 ST Microelectronics
+ * Pratyush Anand <pratyush.anand@st.com>
+ * Mohit Kumar <mohit.kumar@st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+
+/* SPEAr1340 Registers */
+/* Power Management Registers */
+#define SPEAR1340_PCM_CFG			0x100
+	#define SPEAR1340_PCM_CFG_SATA_POWER_EN		BIT(11)
+#define SPEAR1340_PCM_WKUP_CFG			0x104
+#define SPEAR1340_SWITCH_CTR			0x108
+
+#define SPEAR1340_PERIP1_SW_RST			0x318
+	#define SPEAR1340_PERIP1_SW_RSATA		BIT(12)
+#define SPEAR1340_PERIP2_SW_RST			0x31C
+#define SPEAR1340_PERIP3_SW_RST			0x320
+
+/* PCIE - SATA configuration registers */
+#define SPEAR1340_PCIE_SATA_CFG			0x424
+	/* PCIE CFG MASks */
+	#define SPEAR1340_PCIE_CFG_DEVICE_PRESENT	BIT(11)
+	#define SPEAR1340_PCIE_CFG_POWERUP_RESET	BIT(10)
+	#define SPEAR1340_PCIE_CFG_CORE_CLK_EN		BIT(9)
+	#define SPEAR1340_PCIE_CFG_AUX_CLK_EN		BIT(8)
+	#define SPEAR1340_SATA_CFG_TX_CLK_EN		BIT(4)
+	#define SPEAR1340_SATA_CFG_RX_CLK_EN		BIT(3)
+	#define SPEAR1340_SATA_CFG_POWERUP_RESET	BIT(2)
+	#define SPEAR1340_SATA_CFG_PM_CLK_EN		BIT(1)
+	#define SPEAR1340_PCIE_SATA_SEL_PCIE		(0)
+	#define SPEAR1340_PCIE_SATA_SEL_SATA		(1)
+	#define SPEAR1340_PCIE_SATA_CFG_MASK		0xF1F
+	#define SPEAR1340_PCIE_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_PCIE | \
+			SPEAR1340_PCIE_CFG_AUX_CLK_EN | \
+			SPEAR1340_PCIE_CFG_CORE_CLK_EN | \
+			SPEAR1340_PCIE_CFG_POWERUP_RESET | \
+			SPEAR1340_PCIE_CFG_DEVICE_PRESENT)
+	#define SPEAR1340_SATA_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_SATA | \
+			SPEAR1340_SATA_CFG_PM_CLK_EN | \
+			SPEAR1340_SATA_CFG_POWERUP_RESET | \
+			SPEAR1340_SATA_CFG_RX_CLK_EN | \
+			SPEAR1340_SATA_CFG_TX_CLK_EN)
+
+#define SPEAR1340_PCIE_MIPHY_CFG		0x428
+	#define SPEAR1340_MIPHY_OSC_BYPASS_EXT		BIT(31)
+	#define SPEAR1340_MIPHY_CLK_REF_DIV2		BIT(27)
+	#define SPEAR1340_MIPHY_CLK_REF_DIV4		(2 << 27)
+	#define SPEAR1340_MIPHY_CLK_REF_DIV8		(3 << 27)
+	#define SPEAR1340_MIPHY_PLL_RATIO_TOP(x)	(x << 0)
+	#define SPEAR1340_PCIE_MIPHY_CFG_MASK		0xF80000FF
+	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA \
+			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
+			SPEAR1340_MIPHY_CLK_REF_DIV2 | \
+			SPEAR1340_MIPHY_PLL_RATIO_TOP(60))
+	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \
+			(SPEAR1340_MIPHY_PLL_RATIO_TOP(120))
+	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE \
+			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
+			SPEAR1340_MIPHY_PLL_RATIO_TOP(25))
+
+enum spear1340_miphy_mode {
+	SATA,
+	PCIE,
+};
+
+struct spear1340_miphy_priv {
+	/* phy mode: 0 for SATA 1 for PCIe */
+	enum spear1340_miphy_mode	mode;
+	/* regmap for any soc specific misc registers */
+	struct regmap			*misc;
+	/* phy struct pointer */
+	struct phy			*phy;
+};
+
+static int spear1340_miphy_sata_init(struct spear1340_miphy_priv *priv)
+{
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_SATA_CFG,
+			   SPEAR1340_PCIE_SATA_CFG_MASK,
+			   SPEAR1340_SATA_CFG_VAL);
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_MIPHY_CFG,
+			   SPEAR1340_PCIE_MIPHY_CFG_MASK,
+			   SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK);
+	/* Switch on sata power domain */
+	regmap_update_bits(priv->misc, SPEAR1340_PCM_CFG,
+			   SPEAR1340_PCM_CFG_SATA_POWER_EN,
+			   SPEAR1340_PCM_CFG_SATA_POWER_EN);
+	/* Wait for SATA power domain on */
+	msleep(20);
+
+	/* Disable PCIE SATA Controller reset */
+	regmap_update_bits(priv->misc, SPEAR1340_PERIP1_SW_RST,
+			   SPEAR1340_PERIP1_SW_RSATA, 0);
+	/* Wait for SATA reset de-assert completion */
+	msleep(20);
+
+	return 0;
+}
+
+static int spear1340_miphy_sata_exit(struct spear1340_miphy_priv *priv)
+{
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_SATA_CFG,
+			   SPEAR1340_PCIE_SATA_CFG_MASK, 0);
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_MIPHY_CFG,
+			   SPEAR1340_PCIE_MIPHY_CFG_MASK, 0);
+
+	/* Enable PCIE SATA Controller reset */
+	regmap_update_bits(priv->misc, SPEAR1340_PERIP1_SW_RST,
+			   SPEAR1340_PERIP1_SW_RSATA,
+			   SPEAR1340_PERIP1_SW_RSATA);
+	/* Wait for SATA power domain off */
+	msleep(20);
+	/* Switch off sata power domain */
+	regmap_update_bits(priv->misc, SPEAR1340_PCM_CFG,
+			   SPEAR1340_PCM_CFG_SATA_POWER_EN, 0);
+	/* Wait for SATA reset assert completion */
+	msleep(20);
+
+	return 0;
+}
+
+static int spear1340_miphy_pcie_init(struct spear1340_miphy_priv *priv)
+{
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_MIPHY_CFG,
+			   SPEAR1340_PCIE_MIPHY_CFG_MASK,
+			   SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE);
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_SATA_CFG,
+			   SPEAR1340_PCIE_SATA_CFG_MASK,
+			   SPEAR1340_PCIE_CFG_VAL);
+
+	return 0;
+}
+
+static int spear1340_miphy_pcie_exit(struct spear1340_miphy_priv *priv)
+{
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_MIPHY_CFG,
+			   SPEAR1340_PCIE_MIPHY_CFG_MASK, 0);
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_SATA_CFG,
+			   SPEAR1340_PCIE_SATA_CFG_MASK, 0);
+
+	return 0;
+}
+
+static int spear1340_miphy_init(struct phy *phy)
+{
+	struct spear1340_miphy_priv *priv = phy_get_drvdata(phy);
+	int ret = 0;
+
+	if (priv->mode == SATA)
+		ret = spear1340_miphy_sata_init(priv);
+	else if (priv->mode == PCIE)
+		ret = spear1340_miphy_pcie_init(priv);
+
+	return ret;
+}
+
+static int spear1340_miphy_exit(struct phy *phy)
+{
+	struct spear1340_miphy_priv *priv = phy_get_drvdata(phy);
+	int ret = 0;
+
+	if (priv->mode == SATA)
+		ret = spear1340_miphy_sata_exit(priv);
+	else if (priv->mode == PCIE)
+		ret = spear1340_miphy_pcie_exit(priv);
+
+	return ret;
+}
+
+static const struct of_device_id spear1340_miphy_of_match[] = {
+	{ .compatible = "st,spear1340-miphy" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, spear1340_miphy_of_match);
+
+static struct phy_ops spear1340_miphy_ops = {
+	.init = spear1340_miphy_init,
+	.exit = spear1340_miphy_exit,
+	.owner = THIS_MODULE,
+};
+
+#ifdef CONFIG_PM_SLEEP
+static int spear1340_miphy_suspend(struct device *dev)
+{
+	struct spear1340_miphy_priv *priv = dev_get_drvdata(dev);
+	int ret = 0;
+
+	if (priv->mode == SATA)
+		ret = spear1340_miphy_sata_exit(priv);
+
+	return ret;
+}
+
+static int spear1340_miphy_resume(struct device *dev)
+{
+	struct spear1340_miphy_priv *priv = dev_get_drvdata(dev);
+	int ret = 0;
+
+	if (priv->mode == SATA)
+		ret = spear1340_miphy_sata_init(priv);
+
+	return ret;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(spear1340_miphy_pm_ops, spear1340_miphy_suspend,
+			 spear1340_miphy_resume);
+
+static struct phy *spear1340_miphy_xlate(struct device *dev,
+					 struct of_phandle_args *args)
+{
+	struct spear1340_miphy_priv *priv = dev_get_drvdata(dev);
+
+	if (args->args_count < 1) {
+		dev_err(dev, "DT did not pass correct no of args\n");
+		return NULL;
+	}
+
+	priv->mode = args->args[0];
+
+	if (priv->mode != SATA && priv->mode != PCIE) {
+		dev_err(dev, "DT did not pass correct phy mode\n");
+		return NULL;
+	}
+
+	return priv->phy;
+}
+
+static int spear1340_miphy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct spear1340_miphy_priv *priv;
+	struct phy_provider *phy_provider;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv) {
+		dev_err(dev, "can't alloc spear1340_miphy private date memory\n");
+		return -ENOMEM;
+	}
+
+	priv->misc =
+		syscon_regmap_lookup_by_phandle(dev->of_node, "misc");
+	if (IS_ERR(priv->misc)) {
+		dev_err(dev, "failed to find misc regmap\n");
+		return PTR_ERR(priv->misc);
+	}
+
+	priv->phy = devm_phy_create(dev, &spear1340_miphy_ops, NULL);
+	if (IS_ERR(priv->phy)) {
+		dev_err(dev, "failed to create SATA PCIe PHY\n");
+		return PTR_ERR(priv->phy);
+	}
+
+	dev_set_drvdata(dev, priv);
+	phy_set_drvdata(priv->phy, priv);
+
+	phy_provider =
+		devm_of_phy_provider_register(dev, spear1340_miphy_xlate);
+	if (IS_ERR(phy_provider)) {
+		dev_err(dev, "failed to register phy provider\n");
+		return PTR_ERR(phy_provider);
+	}
+
+	return 0;
+}
+
+static struct platform_driver spear1340_miphy_driver = {
+	.probe		= spear1340_miphy_probe,
+	.driver = {
+		.name = "spear1340-miphy",
+		.owner = THIS_MODULE,
+		.pm = &spear1340_miphy_pm_ops,
+		.of_match_table = of_match_ptr(spear1340_miphy_of_match),
+	},
+};
+
+static int __init spear1340_miphy_phy_init(void)
+{
+	return platform_driver_register(&spear1340_miphy_driver);
+}
+module_init(spear1340_miphy_phy_init);
+
+static void __exit spear1340_miphy_phy_exit(void)
+{
+	platform_driver_unregister(&spear1340_miphy_driver);
+}
+module_exit(spear1340_miphy_phy_exit);
+
+MODULE_DESCRIPTION("ST SPEAR1340-MIPHY driver");
+MODULE_AUTHOR("Pratyush Anand <pratyush.anand@st.com>");
+MODULE_LICENSE("GPL v2");